Rework the MIPI interface startup sequence with the following changes:
- Remove MIPI bus initialization from the initial settings blob
- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in
LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At s_stream time enable/disable the MIPI interface output.
- Restore default settings at set_power(0) time.
Before this commit the sensor MIPI interface was initialized with settings
that require a start/stop sequence at power-up time in order to force lanes
into LP11 state, as they were initialized in LP00 when in 'sleep mode',
which is assumed to be the sensor manual definition for the D-PHY defined
stop mode.
The stream start/stop was performed by enabling disabling clock gating,
and had the side effect to change the lanes sleep mode configuration when
stream was stopped.
Clock gating/ungating:
- ret = ov5640_mod_reg(sensor, OV5640_REG_MIPI_CTRL00, BIT(5),
- on ? 0 : BIT(5));
- if (ret)
Set lanes in LP11 when in 'sleep mode':
- ret = ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT00,
- on ? 0x00 : 0x70);
This commit fixes an issue reported by Jagan Teki on i.MX6 platforms that
prevents the host interface from powering up correctly:
https://lkml.org/lkml/2018/6/1/38
It also improves MIPI capture operations stability on my testing platform
where MIPI capture often failed and returned all-purple frames.
Fixes: f22996db44 ("media: ov5640: add support of DVP parallel interface")
Tested-by: Steve Longerbeam <slongerbeam@gmail.com> (i.MX6q SabreSD, CSI-2)
Tested-by: Loic Poulain <loic.poulain@linaro.org> (Dragonboard-410c, CSI-2)
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function not only does initialization but also registers the subdevice
so change its name to make this more clear.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver registers the v4l2 subdevice before attempting to power on the
chip and checking its ID. This means that a media device driver that it's
waiting for this subdevice to be bound, will prematurely expose its media
device node to userspace because if something goes wrong the media entity
will be cleaned up again on the ov2680 probe function.
This also simplifies the probe function error path since no initialization
is made before attempting to enable the resources or checking the chip ID.
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This code doesn't check for NULL consistently and it generates a Smatch
warning:
drivers/media/i2c/sr030pc30.c:575 sr030pc30_base_config()
error: we previously assumed 'info->pdata' could be null (see line 572)
Fortunately, "info->pdata" can't be NULL to that check can be removed.
The other thing is that if "ret" is an error code here, then we don't
want to do the next call to cam_i2c_write(), so actually let's flip that
test around and return the error. This is more of a theoretical issue
than something which is likely to affect real life.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sub-device name is set right after in v4l2_i2c_subdev_init(). Remove
the redundant strcpy() call.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use v4l2_i2c_subdev_set_name() to set the name of the smiapp driver's
sub-devices. There is no functional change.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_i2c_subdev_set_name() can be used to assign a name to a sub-device.
This way uniform names can be formed easily without having to resort to
things such as snprintf in drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently 2-bytes and 3-bytes registers are read one byte at a time,
doing the needed shift & mask each time.
Replace all of this code by a unique helper function that calls
regmap_bulk_read(), which has two advantages:
- reads all the bytes in a unique I2C transaction
- simplifies code to read multibyte registers
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This parameter holds the number of bytes, not bits.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A mix of "mode", "format" and "frmfmt" is used to refer to the sensor
readout mode. Use the term "mode" for all of them. Now "format" is
only used in the V4L2 meaning.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Forcibly setting the subdev name to DRIVER_NAME (i.e. "IMX274") makes
it non-unique and less informative.
Let the driver use the default name from i2c, e.g. "IMX274 2-001a".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rearrange the imx274_start_<N> register tables to better match the
datasheet and slightly simplify code:
- collapes tables 1 and 2, they are applied one after each other and
together they implement the fixed part 1 of the startup procedure
in the datasheet
- while there, cleanup comments
- rename tables 3 and 4 -> 2 and 3, coherently with the datasheet
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The "mode" has been renamed to "binning" in commit 39dd23dc9d
("media: imx274: add cropping support via SELECTION API"), but this
define has not been updated.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The device is already suspended when it's the driver's remove function is
called. Remove redundant pm_runtime_set_suspended call.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the DT binding documentation for dw9714 and dw9807-vcm to the
MAINTAINERS file. The dw9807-vcm binding documentation file is renamed to
match the dw9807's VCM bit's compatible string.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The UDS is currently restricted based on a partition size of 256 pixels.
Document the actual restrictions, but don't increase the implementation.
The extended partition algorithm may later choose to utilise a larger
partition size to support overlapping partitions which will improve the
quality of the output images.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The SRU is currently restricted to 256 pixels as part of the current
partition algorithm. Document that the actual capability of this
component is 288 pixels, but don't increase the implementation.
The extended partition algorithm may later choose to utilise a larger
input to support overlapping partitions which will improve the quality
of the output images.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The style of this driver uses periods at the end of sentences in
comments, but it is applied inconsitently.
Update a selection of comments which were discovered to be missing their
period. Also fix the spelling of one usage of 'instantiate'
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The VSP1 has a minimum width and height of a single pixel, with the
exception of pixel formats with sub-sampling.
Remove the artificial minimum width and minimum height limitation, and
instead clamp the minimum dimensions based upon the sub-sampling
parameter of that dimension.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
YCbCr planar formats can have different pitch values for the luma and
chroma planes. This isn't taken into account in the driver. Fix it.
Based on a BSP patch from Koji Matsuoka <koji.matsuoka.xm@renesas.com>.
Fixes: 7863ac504b ("drm: rcar-du: Add tri-planar memory formats support")
[Updated documentation of the struct vsp1_du_atomic_config pitch field]
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The LIF module has a data buffer to accommodate clock rate differences
between the DU and the VSP. Several programmable threshold values
control DU start of frame notification by the VSP and VSP clock
stop/resume. The R-Car Gen2 and Gen3 datasheets recommend values for the
different SoCs. Update the driver to use the recommended values for
optimal operation.
Based on a BSP patch from Koji Matsuoka <koji.matsuoka.xm@renesas.com>,
with Gen2 and V3H/V3M updates.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All source files of the vsp1 driver are licensed under the GPLv2+ except
for vsp1_regs.h which is licensed under GPLv2. This is caused by a bad
copy&paste that dates back from the initial version of the driver. Fix
it.
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Sergei Shtylyov<sergei.shtylyov@cogentembedded.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The recent tvp5150 patchset added two new warnings:
drivers/media/i2c/tvp5150.c: In function 'tvp5150_querystd':
drivers/media/i2c/tvp5150.c:829:18: warning: unused variable 'decoder' [-Wunused-variable]
struct tvp5150 *decoder = to_tvp5150(sd);
^~~~~~~
drivers/media/i2c/tvp5150.c:1522:6: warning: no previous prototype for 'tvp5150_volatile_reg' [-Wmissing-prototypes]
bool tvp5150_volatile_reg(struct device *dev, unsigned int reg)
^~~~~~~~~~~~~~~~~~~~
Get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When irq is used, the lock is set via IRQ code. When it isn't,
the driver just assumes it is always locked. Instead, read the
lock status from the status register.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the querystd video_op and make it return V4L2_STD_UNKNOWN while the
TVP5150 is not locked to a signal.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add callback to retrieve the current set norm.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Issue a V4L2_EVENT_SOURCE_CHANGE notification when the TVP5150 locks
onto a signal and when it loses the lock.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[m.felsch@pengutronix.de: partly mainline part port]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To avoid short frames on stream start, keep output pins at high impedance
while we are not properly locked onto the input signal.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds an optional interrupt handler to handle the sync
lock interrupt and sync lock status.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[m.felsch@pengutronix.de: move added .g_std callback to separate patch]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To allow optional interrupt support, we want to configure the pin settings
dynamically. Move those register accesses out of the static initialization
tables.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[m.felsch@pengutronix.de: drop init_default register remove]
[m.felsch@pengutronix.de: fix regmap access during reset()]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To trigger standard autodetection only the reset part of the routine
is necessary during probe(). Split this out to make it callable on its own.
[m.felsch@pengutronix.de: adapt commit message]
[m.felsch@pengutronix.de: add tvp5150_enable() to tvp5150_s_stream()]
[m.chehab@samsung.com: fix a compilation breakage]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make sure to not overwrite decoder->norm when setting the standard
in hardware, but only when instructed by V4L2 API calls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If cropping isn't set explicitly by userspace, reset it to the maximum
possible rectangle in subdevice open if a standard change is detected.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[m.felsch@pengutronix.de: move code from internal_ops.open() to pad_ops.init_cfg()]
[m.felsch@pengutronix.de: make use of tvp5150_set_default() helper]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The patch adds three macros to bundle the mbus_framefmt default
values and a helper function to set the the default crop and
mbus_framefmt values.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add two helper functions to check if two rectangles have the same
position (top/left) and if two rectangles equals (same size and
same position).
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 9a4c7e68f7e0 ("media: tvp5150: convert register
access to regmap")' the driver supports regmap. Now we can drop
the handmade bit update sequence and move to the regmap provided
helpers.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Regmap provides built in debugging, caching and provides dedicated
accessors for bit manipulations in registers, which make the following
changes a lot simpler.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function only consists of a single switch case block without a
default case. Unsupported control requests are indicated by the -EINVAL
return code trough the last return statement at the end of the function. So
exiting just the switch case block returns the -EINVAL error code but the
hue control is supported and a zero should be returned instead.
Replace the break by a 'return 0' to fix this behaviour.
Fixes: d183e4efca ("[media] v4l: tvp5150: Add missing break in set
control handler")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver ignored the width alignment which exists due to the UYVY
colorspace format. Fix the width alignment and make use of the the
provided v4l2 helper function to set the width, height and all
alignments in one.
Fixes: 963ddc63e2 ("[media] media: tvp5150: Add cropping support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Now that all drivers are using pad signal types, we can get
rid of the global static definition, as routes are stablished
using the pad signal type.
The tuner and IF-PLL pads are now used only by the tuner core,
so move the definitions to be there.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jacopo Mondi