We have four Qualcomm-related pin control drivers, and now there
are drivers coming in for the PMICs on these systems, so let's
create a qcom subdirectory to hold all the Qualcomm stuff.
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Marvell Berlin boards have a group based pinmuxing mechanism. This
adds the core driver support. We actually do not need any information
about the pins here and only have the definition of the groups.
Let's take the example of the uart0 pinmuxing on the BG2Q. Balls BK4 and
BH6 are muxed to respectively UART0 RX and TX if the group GSM12 is set
to mode 0:
Group Modes Offset Base Offset LSB Bit Width
GSM12 3 sm_base 0x40 0x10 0x2
Ball Group Mode 0 Mode 1 Mode 2
BK4 GSM12 UART0_RX IrDA0_RX GPIO9
BH6 GSM12 UART0_TX IrDA0_TX GPIO10
So in order to configure BK4 -> UART0_TX and BH6 -> UART0_RX, we need
to set (sm_base + 0x40 + 0x10) &= ff3fffff.
As pin control registers are part of either chip control or system
control registers, that deal with a bunch of other functions we rely
on a regmap instead of exclusively remapping any resources.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pinctrl definitions for the GPIO pins of the TLMM v2 block in the
Qualcomm IPQ8064 platform.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pinctrl definitions for the GPIO pins of the TLMM v2 block in the
Qualcomm APQ8064 platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To be consistent with other Broadcom drivers, the Broadcom Capri pinctrl
driver and its related CONFIG option are renamed to bcm281xx.
Devicetree compatible string and binding documentation use
"brcm,bcm11351-pinctrl" to match the machine binding here:
Documentation/devicetree/bindings/arm/bcm/bcm11351.txt
This driver supports pinctrl on BCM11130, BCM11140, BCM11351, BCM28145
and BCM28155 SoCs.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Matt Porter <mporter@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds pinctrl driver for Broadcom Capri (BCM281xx) SoCs.
v4: - PINCTRL selected in Kconfig, PINCTRL_CAPRI selected in bcm_defconfig
- make use of regmap
- change CAPRI_PIN_UPDATE from macro to inline function.
- Handle pull-up strength arg in Ohm instead of enum
v3: Re-work driver to be based on generic pin config. Moved config selection
from Kconfig to bcm_defconfig.
v2: Use hyphens instead of underscore in DT property names.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a driver for the Tegra124 pinmux, and required
parameterization data for Tegra124.
The driver uses the common Tegra pincontrol driver utility
functions to implement the majority of the driver.
This driver is not compatible with the earlier NVIDIA's SoCs,
hence add new compatibile as "nvidia,tegra124-pinmux".
Originally written by Ashwini Gguhe.
Thierry:
- Cleanups in patches.
ldewangan:
- Fix some entries for groups.
- Fix MUX enums and group sequence.
Signed-off-by: Ashwini Ghuge <aghuge@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
CC: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial definition of parameters for pinctrl-msm for the msm8x74
platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a pinctrl, pinmux, pinconf and gpiolib driver for the
Qualcomm TLMM block.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is mostly cut and paste from the imx35 pinctrl driver.
The data was generated using sed and awk on
arch/arm/plat-mxc/include/mach/iomux-mx25.h.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add code to support the specific pin arrangements of the Freescale IMX50 SoC.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
imx27 pincontrol driver using the imx1 core driver. The DT bindings are
similar to other imx pincontrol drivers.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core driver for register formats of imx1/imx21/imx27 processors.
The pins of those processors are grouped into ports. Each port has 32
pins. The pins mux configuration is controlled by registers with 1 or 2
bit per pin, depending on the specific control register.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinmux driver of the Abilis Systems TB10x platform based on ARC700 CPUs.
Used to control the pinmux and is a prerequisite for the GPIO driver.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AS3722 is a compact system PMU suitable for mobile phones, tablets etc.
Add a driver to support accessing the GPIO, pinmux and pin configuration
of 8 GPIO pins found on the ams AS3722 through pin control driver and
gpiolib.
The driver will register itself as the pincontrol driver and gpio driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new ADI GPIO2 controller was introduced since the BF548 and BF60x
processors. It differs a lot from the old one on BF5xx processors. So,
create a pinctrl driver under the pinctrl framework.
- Define gpio ports and pin interrupt controllers as individual platform
devices.
- Register a pinctrl driver for the whole GPIO ports and pin interrupt
devices.
- Probe pint devices before port devices. Put device instances into
the global gpio and pint lists.
- Define peripheral, irq and gpio reservation bit masks for each gpio
port as runtime resources.
- Save and restore gpio port and pint status MMRs in syscore PM functions.
- Create the plug-in subdrivers to hold the pinctrl soc data for bf54x
and bf60x. Add soc data into struct adi_pinctrl. Initialize the soc data
in pin controller probe function. Get the pin groups and functions via
the soc data reference.
- Call gpiochip_add_pin_range() in gpio device probe function to register
range cross reference between gpio device and pin control device.
- Get range by pinctrl_find_gpio_range_from_pin(), find gpio_port object
by container_of() and find adi_pinctrl by pin control device name.
- Handle peripheral and gpio requests in pinctrl operation functions.
- Demux gpio IRQs via the irq_domain created by each GPIO port.
v2-changes:
- Remove unlinke() directive.
v3-changes:
- Rename struct adi_pmx to adi_pinctrl.
- Fix the comments of struct gpio_pint.
- Remove unused pin_base in struct gpio_port.
- Change pint_assign into bool type.
- Add comments about the relationship between pint device and port device
to the driver header.
- Use BIT macro to shift bit.
- Remove all bitmap reservation help functions. Inline reservation functions
into the actual code.
- Remove gpio and offset mutual reference help functions.
- Remove all help functions to find gpio_port and adi_pinctrl structs. Get
range by pinctrl_find_gpio_range_from_pin(), find gpio_port object by
container_of() and find adi_pinctrl by pin control device name.
- Pass bool type usage variable to port_setup help function.
- Separate long bit operations into several lines and add comments.
- Use debugfs to output all GPIO request information.
- Avoid to set drvdata to NULL
- Add explanation to function adi_gpio_init_int()
- Call gpiochip_add_pin_range() in gpio device probe function to register
range cross reference between gpio device and pin control device.
- Remove the reference to pin control device from the gpio_port struct.
Remove the reference list to gpio device from the adi_pinctrl struct.
Replace the global adi_pinctrl list with adi_gpio_port_list. Walk through
the gpio list to do power suspend and resume operations.
- Remove the global GPIO base from struct adi_pinctrl, define pin base in
the platform data for each GPIO port device.
- Initialize adi_pinctrl_setup in arch_initcall().
- print the status of triggers, whether it is in GPIO mode, if it is
flagged to be used as IRQ, etc in adi_pin_dbg_show().
- Create the plug-in subdrivers to hold the pinctrl soc data for bf54x
and bf60x. Add soc data into struct adi_pinctrl. Initialize the soc data
in pin controller probe function. Get the pin groups and functions via
the soc data reference.
v4-changes:
- remove useless system_state checking.
- replace dev_err with dev_warn in both irq and gpio pin cases.
- comment on relationship between irq type and invert operation.
- It is not necessary to check the reservation mode of the requested
pin in IRQ chip operation. Remove the reservation map.
- Use existing gpio/pinctrl subsystem debugfs files. Remove pinctrl-adi2
driver specific debugfs output.
- Add linkport group and function information for bf60x.
- Separate uart and ctsrts pins into 2 groups.
- Separate APAPI and alternative ATAPI pins into 2 groups.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
TI Palmas series Power Management IC have multiple pins which can be
configured for different functionality. This pins can be configured
for different function. Also their properties like pull up/down,
open drain enable/disable are configurable.
Add support for pincontrol driver Palmas series device like TPS65913,
TPS80036. The driver supports to be register from DT only.
Changes from V1:
- Add generic property for pins and functions in pinconf-generic.
- Add APIs to map the DT and subnode.
- Move common utils APIs to the pinctrl-utils from this file.
- Update the binding document accordingly.
Changes from V2:
- Add ack by Lee.
- Correct the binding docs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some of pincontrol driver needs the utility function to create map
list. The utility function needed for adding mux, configs etc.
In place of duplicating this in each driver, add the common utility
function in common file and use from device specific driver. This will
reduce the duplicating of code across drivers.
Changes from V1:
- Add this files in this patch and add common utility APIs to here.
Changes from V2:
- Nothing in code.
- Added Reviewed by Stephen.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- A large slew of improvements of the Genric pin configuration
support, and deployment in four different platforms:
Rockchip, Super-H PFC, ABx500 and TZ1090. Support BIAS_BUS_HOLD,
get device tree parsing and debugfs support into shape.
- We also have device tree support with generic naming conventions
for the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now
handled in the device core: "sleep" and "idle", removing a lot
of boilerplate code in drivers. We do not yet know if this is
the final word for pin PM, but it already make things a lot
easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where
several pins are managed by a single register, and augment it to
handle sleep modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=EbAf
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
A small but useful set of regmap updates this time around:
- An abstraction for bitfields within a register map contributed by
Srinivas Kandagatla, allowing drivers to cope more easily when
hardware designers randomly move things about (mainly when talking
to things like system controllers).
- Changes from Lars-Peter Clausen to allow the MMIO regmap to be used from
hard IRQ context.
- Small improvements to the cache infrastructure and performance,
including a default cache sync operation so now all regmaps can sync
easily.
There's also a pinctrl driver making use of the new bitfield API, merged
here for dependency reasons. There will be a simple add/add conflict
with the pinctrl tree as a result.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8WLH
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A small but useful set of regmap updates this time around:
- An abstraction for bitfields within a register map contributed by
Srinivas Kandagatla, allowing drivers to cope more easily when
hardware designers randomly move things about (mainly when talking
to things like system controllers).
- Changes from Lars-Peter Clausen to allow the MMIO regmap to be used
from hard IRQ context.
- Small improvements to the cache infrastructure and performance,
including a default cache sync operation so now all regmaps can
sync easily.
There's also a pinctrl driver making use of the new bitfield API,
merged here for dependency reasons. There will be a simple add/add
conflict with the pinctrl tree as a result."
* tag 'regmap-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
pinctrl: st: Remove unnecessary use of of_match_ptr macro
pinctrl: st: fix return value check
pinctrl: st: Add pinctrl and pinconf support.
regmap: debugfs: Suppress cache for partial register files
regmap: Add regmap_field APIs
regmap: core: Cache all registers by default when cache is enabled
regmap: Implemented default cache sync operation
regmap: Make regmap-mmio usable from atomic contexts
regmap: regcache: Fixup locking for custom lock callbacks
regmap: debugfs: Fix return from regmap_debugfs_get_dump_start
regmap: debugfs: Don't mark lockdep as broken due to debugfs write
regmap: rbtree: Use range information to allocate nodes
regmap: rbtree: Factor out node allocation
regmap: Make regmap_check_range_table() a public API
regmap: Add support for discarding parts of the register cache
This patch add pinctrl support to ST SoCs.
About hardware:
ST Set-Top-Box parts have two blocks called PIO and PIO-mux which handle
pin configurations.
Each multi-function pin is controlled, driven and routed through the PIO
multiplexing block. Each pin supports GPIO functionality (ALT0) and
multiple alternate functions(ALT1 - ALTx) that directly connect the pin
to different hardware blocks. When a pin is in GPIO mode, Output Enable
(OE), Open Drain(OD), and Pull Up (PU) are driven by the related PIO
block. Otherwise the PIO multiplexing block configures these parameters
and retiming the signal.
About driver:
This pinctrl driver manages both PIO and PIO-mux block using pinctrl,
pinconf, pinmux, gpio subsystems. All the pinctrl related config
information can only come from device trees.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a pin control driver for the TZ1090's low power pins via the
powerdown controller SOC_GPIO_CONTROL registers.
These pins have individually controlled pull-up, and group controlled
schmitt, slew-rate, drive-strength, and power-on-start (pos).
The pdc_gpio0 and pdc_gpio1 pins can also be muxed onto the
ir_mod_stable_out and ir_mod_power_out functions respectively. If no
function is set they remain in GPIO mode. These muxes can be overridden
by requesting them as GPIOs.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a pin control driver for the main pins on the TZ1090 SoC. This
doesn't include the low-power pins as they're controlled separately via
the Powerdown Controller (PDC) registers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for gpio on Intel BayTrail platforms. BayTrail supports 3 banks
of gpios called SCORE, NCORE ans SUS with 102, 28 and 44 gpio pins.
Supports gpio interrupts and ACPI gpio events
Pins may be muxed to alternate function instead of gpio by firmware.
This driver does not touch the pin muxing and expect firmare
to set pin muxing and pullup/down properties properly.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver adds support the Cortex-A9 based SoCs from Rockchip,
so at least the RK2928, RK3066 (a and b) and RK3188.
Earlier Rockchip SoCs seem to use similar mechanics for gpio
handling so should be supportable with relative small changes.
Pull handling on the rk3188 is currently a stub, due to it being
a bit different to the earlier SoCs.
Pinmuxing as well as gpio (and interrupt-) handling tested on
a rk3066a based machine.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
atlas6 is a SoC very similar with primaII, the register layput of
pinctrl is same, but the pads, groups and functions of atlas6 have
different layout with prima2, this patch
1. pull the definition of pads, groups and functions out of the
pinctrl-sirf driver,and put them into soc-specific files
2. add pads, groups and functions tables for atlas6
3. let pads, groups and functions tables become the config data of
the related dt compatible node, so the pinctrl-sirf can support
all SiRF SoCs with the config data as private data.
In this patch,we create a sirf dir, and let
the old drivers/pinctrl/pinctrl-sirf.c =
drivers/pinctrl/sirf/pinctrl-prima2.c +
drivers/pinctrl/sirf/pinctrl-sirf.c
drivers/pinctrl/sirf/pinctrl-atlas6.c is a newly created file for the
pin layout of atlas6.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl-imx6sl is in place. Enable the build of it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The s3c24xx pins follow a similar pattern as the other Samsung SoCs and
can therefore reuse the already introduced infrastructure.
The s3c24xx SoCs have one design oddity in that the first 4 external
interrupts do not reside in the eint pending register but in the main
interrupt controller instead. We solve this by forwarding the external
interrupt from the main controller into the irq domain of the pin bank.
The masking/acking of these interrupts is handled in the same way.
Furthermore the S3C2412/2413 SoCs contain another oddity in that they
keep the same 4 eints in the main interrupt controller and eintpend
register and requiring ack operations to happen in both. This is solved
by using different compatible properties for the wakeup eint node which
set a property accordingly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem
specific interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into
platform specific interface, or to get called from platform specific
code, as long as all information about the hardware is provided
through a device tree.
Most of the drivers we touch this time are for clocksource. Since
now most of them are part of drivers/clocksource, I expect that we
won't have to touch these again from arm-soc and can let the
clocksource maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the
merge conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface
for taking devices on the SoC out of reset or back into reset.
Patches to use this interface on i.MX follow later in this merge
window, and we are going to have other platforms (at least tegra
and sirf) get converted in 3.11. This will let us get rid of
platform specific callbacks in a number of platform independent
device drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZWk9
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem specific
interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into platform
specific interface, or to get called from platform specific code, as
long as all information about the hardware is provided through a
device tree.
Most of the drivers we touch this time are for clocksource. Since now
most of them are part of drivers/clocksource, I expect that we won't
have to touch these again from arm-soc and can let the clocksource
maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the merge
conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface for
taking devices on the SoC out of reset or back into reset. Patches to
use this interface on i.MX follow later in this merge window, and we
are going to have other platforms (at least tegra and sirf) get
converted in 3.11. This will let us get rid of platform specific
callbacks in a number of platform independent device drivers."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (256 commits)
irqchip: s3c24xx: add missing __init annotations
ARM: dts: Disable the RTC by default on exynos5
clk: exynos5250: Fix parent clock for sclk_mmc{0,1,2,3}
ARM: exynos: restore mach/regs-clock.h for exynos5
clocksource: exynos_mct: fix build error on non-DT
pinctrl: vt8500: wmt: Fix checking return value of pinctrl_register()
irqchip: vt8500: Convert arch-vt8500 to new irqchip infrastructure
reset: NULL deref on allocation failure
reset: Add reset controller API
dt: describe base reset signal binding
ARM: EXYNOS: Add arm-pmu DT binding for exynos421x
ARM: EXYNOS: Add arm-pmu DT binding for exynos5250
ARM: EXYNOS: Enable PMUs for exynos4
irqchip: exynos-combiner: Correct combined IRQs for exynos4
irqchip: exynos-combiner: Add set_irq_affinity function for combiner_irq
ARM: EXYNOS: fix compilation error introduced due to common clock migration
clk: exynos5250: Fix divider values for sclk_mmc{0,1,2,3}
clk: exynos4: export clocks required for fimc-is
clk: samsung: Fix compilation error
clk: tegra: fix enum tegra114_clk to match binding
...
Device-tree updates for 3.10. The bulk of the churn in this branch is due
to i.MX moving from C-defined pin control over to device tree, which is
a one-time conversion that will allow greater flexibility down the road.
Besides that, there's PCI-e bindings for Marvell mvebu platforms and a
handful of cleanups to tegra due to the new include file functionality
of the device tree compiler.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8X1b
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree updates from Olof Johansson:
"Part 1 of device-tree updates for 3.10. The bulk of the churn in this
branch is due to i.MX moving from C-defined pin control over to device
tree, which is a one-time conversion that will allow greater
flexibility down the road.
Besides that, there's PCI-e bindings for Marvell mvebu platforms and a
handful of cleanups to tegra due to the new include file functionality
of the device tree compiler"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (113 commits)
arm: mvebu: PCIe Device Tree informations for Armada XP GP
arm: mvebu: PCIe Device Tree informations for Armada 370 DB
arm: mvebu: PCIe Device Tree informations for Armada 370 Mirabox
arm: mvebu: PCIe Device Tree informations for Armada XP DB
arm: mvebu: PCIe Device Tree informations for OpenBlocks AX3-4
arm: mvebu: add PCIe Device Tree informations for Armada XP
arm: mvebu: add PCIe Device Tree informations for Armada 370
ARM: sunxi: unify osc24M_fixed and osc24M
arm: vt8500: Add SDHC support to WM8505 DT
ARM: dts: Add a 64 bits version of the skeleton device tree
ARM: mvebu: Add Device Bus and CFI flash memory support to defconfig
ARM: mvebu: Add support for NOR flash device on Openblocks AX3 board
ARM: mvebu: Add support for NOR flash device on Armada XP-GP board
ARM: mvebu: Add Device Bus support for Armada 370/XP SoC
ARM: dts: imx6dl-wandboard: Add USB Host support
ARM: dts: imx51 cpu node
ARM: dts: Add missing imx27-phytec-phycore dtb target
ARM: dts: Add NFC support for i.MX27 Phytec PCM038 module
ARM: i.MX51: Add PATA support
ARM: dts: Add initial support for Wandboard Dual-Lite
...
The imx6dl is a derivative of imx6q with very limited difference. These
two SoCs are so compatible that they can be handled as one platform in
software. That said, we will not have target SOC_IMX6DL but just
reusing SOC_IMX6Q. That's why the pinctrl-imx6dl driver is added here
with symbol PINCTRL_IMX6Q controlling the build of it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds pinctrl-s3c64xx driver which implements pin control
interface for Samsung S3C64xx SoCs.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for the GPIO/pinmux controller found on the VIA
VT8500 and Wondermedia WM8xxx-series SoCs.
Each pin within the controller is capable of operating as a GPIO or as
an alternate function. The pins are numbered according to their control
bank/bit so that if new pins are added, the existing numbering is maintained.
All currently supported SoCs are included: VT8500, WM8505, WM8650, WM8750 and
WM8850.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl-pxa driver doesn't support well on DT mode. Now pinctrl-single
could support DT mode & pin configuration. Use pinctrl-single driver to
support MMP/PXA silicons instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is another cleanup series, containing the move of the Renesas
SH-Mobile pin controller code from arch/arm/mach-shmobile over to the
generic pinctrl subsystem, changing it over to the common interfaces in
the process.
Based on agreement between Olof, Paul Mundt, Linus Walleij and Simon,
we're merging this large branch of pinctrl conversion through arm-soc,
even though it contains the corresponding conversions for arch/sh. Main
reason for this is tight dependencies (that will now mostly be broken)
between the arch/sh and mach-shmobile implementations.
There will be more of this in 3.10 to do device-tree bindings, but this
is the initial conversion.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=U+ce
-----END PGP SIGNATURE-----
Merge tag 'sh-pinmux' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull sh-mobile pinctrl conversion from Arnd Bergmann:
"This is another cleanup series, containing the move of the Renesas
SH-Mobile pin controller code from arch/arm/mach-shmobile over to the
generic pinctrl subsystem, changing it over to the common interfaces
in the process.
Based on agreement between Olof, Paul Mundt, Linus Walleij and Simon,
we're merging this large branch of pinctrl conversion through arm-soc,
even though it contains the corresponding conversions for arch/sh.
Main reason for this is tight dependencies (that will now mostly be
broken) between the arch/sh and mach-shmobile implementations.
There will be more of this in 3.10 to do device-tree bindings, but
this is the initial conversion."
* tag 'sh-pinmux' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (81 commits)
sh-pfc: sh_pfc_probe() sizeof() fix
sh-pfc: Move sh_pfc.h from include/linux/ to driver directory
sh-pfc: Remove pinmux_info definition
sh: Remove unused sh_pfc_register_info() function
sh: shx3: pinmux: Use driver-provided pinmux info
sh: sh7786: pinmux: Use driver-provided pinmux info
sh: sh7785: pinmux: Use driver-provided pinmux info
sh: sh7757: pinmux: Use driver-provided pinmux info
sh: sh7734: pinmux: Use driver-provided pinmux info
sh: sh7724: pinmux: Use driver-provided pinmux info
sh: sh7723: pinmux: Use driver-provided pinmux info
sh: sh7722: pinmux: Use driver-provided pinmux info
sh: sh7720: pinmux: Use driver-provided pinmux info
sh: sh7269: pinmux: Use driver-provided pinmux info
sh: sh7264: pinmux: Use driver-provided pinmux info
sh: sh7203: pinmux: Use driver-provided pinmux info
ARM: shmobile: sh73a0: Use driver-provided pinmux info
ARM: shmobile: sh7372: Use driver-provided pinmux info
ARM: shmobile: r8a7779: Use driver-provided pinmux info
ARM: shmobile: r8a7740: Use driver-provided pinmux info
...
Add AB8540 sub driver to the ABx500 family, pins, pin groups and
gpio range.
As the pin controller (also the ABx500 controllers) is an
inherent part of the SoC and will prevent boot if not
available, select this from the Ux500 SoC Kconfig.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add AB9540 sub driver to the ABx500 family, pins, pin groups and
gpio range.
As the pin controller (also the ABx500 controllers) is an
inherent part of the SoC and will prevent boot if not
available, select this from the Ux500 SoC Kconfig.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add AB8505 sub driver to the ABx5x family.
As the pin controller (also the ABx500 controllers) is an
inherent part of the SoC and will prevent boot if not
available, select this from the Ux500 SoC Kconfig.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a subdriver for the AB8500 pinctrl portions.
As the pin controller (also the ABx500 controllers) is an
inherent part of the SoC and will prevent boot if not
available, select this from the Ux500 SoC Kconfig.
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the AB8500 core driver, which will be utilized by
the follow-on drivers for different ABx500 variants.
Sselect the driver from the DBX500_SOC, as this chip is
powering and clocking that SoC.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Allwinner SoCs have an IP module that handle both the muxing and the
GPIOs.
This IP has 8 banks of 32 bits, with a number of pins actually useful
for each of these banks varying from one to another, and depending on
the SoC used on the board.
This driver only implements the pinctrl part, the gpio part will come
eventually.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since pinctrl-exynos can support exynos4 and exynos5 so changed
the option name to PINCTRL_EXYNOS for more clarity.
Cc: Thomas Abraham <Thomas.abraham@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a driver for the Tegra114 pinmux, and required
parameterization data for Tegra114.
The driver uses the common Tegra pincontrol driver utility
functions to implement the majority of the driver.
This driver is not compatible with the earlier NVIDIA's SoCs,
hence add new compatibile as "nvidia,tegra114-pinmux".
Originally written by Pritesh.
ldewangan:
- cleanup the patches,
- remove non-require tables.
- Use module_platform_driver() for driver registartion.
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij