This patchset corrects a rebind issue on STM32 SPDIFRX and I2S drivers.
The same correction has already been applied for SAI driver:
0d6defc7e0 ("ASoC: stm32: sai: manage rebind issue")
The commit e894efef9a ("ASoC: core: add support to card rebind")
allows to rebind the sound card after a rebind of one of its component.
With this commit, the sound card is actually rebound,
but may be no more functional.
The following problems have been seen on STM32 drivers.
1) DMA channel is not requested:
With the sound card rebind the simplified call sequence is:
probe
snd_soc_register_component
snd_soc_try_rebind_card
snd_soc_instantiate_card
devm_snd_dmaengine_pcm_register
The problem occurs because the pcm must be registered,
before snd_soc_instantiate_card() is called.
Modify the driver, to change the call sequence as follows:
probe
devm_snd_dmaengine_pcm_register
snd_soc_register_component
snd_soc_try_rebind_card
2) DMA channel is not released:
dma_release_channel() is not called when
devm_dmaengine_pcm_release() is executed.
This occurs because SND_DMAENGINE_PCM_DRV_NAME component,
has already been released through devm_component_release().
devm_dmaengine_pcm_release() should be called before
devm_component_release() to avoid this problem.
Call snd_dmaengine_pcm_unregister() and snd_soc_unregister_component()
explicitly from the driver, to have the right sequence.
Olivier Moysan (3):
ASoC: stm32: spdifrx: fix regmap status check
ASoC: stm32: spdifrx: manage rebind issue
ASoC: stm32: i2s: manage rebind issue
sound/soc/stm/stm32_i2s.c | 40 ++++++++++++++++------
sound/soc/stm/stm32_spdifrx.c | 64 +++++++++++++++++++----------------
2 files changed, 63 insertions(+), 41 deletions(-)
--
2.17.1
Recent addition of SoundWire stream state-machine checks in linux-next
have shown an existing issue with handling soundwire streams in codec drivers.
In general soundwire stream prepare/enable/disable can be called from either
codec/machine/controller driver. However calling it in codec driver means
that if multiple instances(Left/Right speakers) of the same codec is
connected to the same stream then it will endup calling stream
prepare/enable/disable more than once. This will mess up the stream
state-machine checks in the soundwire core.
Moving this stream handling to machine driver would fix this issue
and also allow board/platform specfic power sequencing.
Changes since v1:
- removed false error check while setting sruntime.
Srinivas Kandagatla (2):
ASoC: qcom: sdm845: handle soundwire stream
ASoC: codecs: wsa881x: remove soundwire stream handling
sound/soc/codecs/wsa881x.c | 44 +------------------------
sound/soc/qcom/Kconfig | 2 +-
sound/soc/qcom/sdm845.c | 67 ++++++++++++++++++++++++++++++++++++++
3 files changed, 69 insertions(+), 44 deletions(-)
--
2.21.0
In existing setup WSA881x codec handles soundwire stream,
however DB845c and other machines based on SDM845c have 2
instances for WSA881x codec. This will force soundwire stream
to be prepared/enabled twice or multiple times.
Handling SoundWire Stream in machine driver would fix this issue.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317151233.8763-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There could be multiple instances of this codec on any platform,
so handling stream directly in this codec driver can lead to
multiple calls to prepare/enable/disable on the same SoundWire stream.
Move this stream handling to machine driver to fix this issue.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200317151233.8763-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit e894efef9a ("ASoC: core: add support to card rebind")
allows to rebind the sound card after a rebind of one of its component.
With this commit, the sound card is actually rebound,
but may be no more functional.
Corrections:
- Call snd_dmaengine_pcm_register() before snd_soc_register_component().
- Call snd_dmaengine_pcm_unregister() and snd_soc_unregister_component()
explicitly from I2S driver.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20200318144125.9163-4-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit e894efef9a ("ASoC: core: add support to card rebind")
allows to rebind the sound card after a rebind of one of its component.
With this commit, the sound card is actually rebound,
but may be no more functional.
Corrections:
- Call snd_dmaengine_pcm_register() before snd_soc_register_component().
- Call snd_dmaengine_pcm_unregister() and snd_soc_unregister_component()
explicitly from SPDFIRX driver.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20200318144125.9163-3-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series adds more WMA profiles and WMA decoder parameters to UAPI and
then support for these in qcom driver. It also adds FLAC and APE IDs and
decoder parameters to UAPI and then support in qcom driver
This was tested on Dragon board RB3.
Last, bump up the compressed version so that userspace can check for the
support.
Since the series touches compress uapi and asoc, it would make sense to go
thru asoc tree with acks.
Changes in v3:
- add r-b from Srini
- use macros for FLAC channel layout tags
Changes in v2:
- use bitflags for wma profiles
Vinod Koul (9):
ALSA: compress: add wma codec profiles
ALSA: compress: Add wma decoder params
ASoC: qcom: q6asm: pass codec profile to q6asm_open_write
ASoC: qcom: q6asm: add support to wma config
ASoC: qcom: q6asm-dai: add support to wma decoder
ALSA: compress: add alac & ape decoder params
ASoC: qcom: q6asm: add support for alac and ape configs
ASoC: qcom: q6asm-dai: add support for ALAC and APE decoders
ALSA: compress: bump the version
include/uapi/sound/compress_offload.h | 2 +-
include/uapi/sound/compress_params.h | 37 +++-
sound/soc/qcom/qdsp6/q6asm-dai.c | 139 ++++++++++++++-
sound/soc/qcom/qdsp6/q6asm.c | 243 +++++++++++++++++++++++++-
sound/soc/qcom/qdsp6/q6asm.h | 51 +++++-
5 files changed, 465 insertions(+), 7 deletions(-)
--
2.24.1
snd_soc_dai_get_sdw_stream() returns null if dai does not support
this callback, this is no very useful for the caller to
differentiate if this is an error or unsupported call for the dai.
return -ENOTSUPP in cases where this callback is not supported.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200316151110.2580-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We have added support for bunch of new decoders and parameters for
decoders. To help users find the support bump the version up to 0,2,0.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200316055221.1944464-10-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm DSPs also supports the ALAC and APE decoders, so add support
for these and convert the snd_codec_params to qdsp format.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200316055221.1944464-9-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm DSPs expect ALAC and APE configs to be send for decoders,
so add the API to program the respective config to the DSP.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200316055221.1944464-8-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm DSPs also supports the wma decoder, so add support for wma
decoder and convert the snd_codec_params to qdsp format.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200316055221.1944464-6-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm DSPs expect wma v9 and wma v10 configs to be set for wma
decoders, so add the API to program the respective wma config to the DSP
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200316055221.1944464-5-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Codec profile is required to be passed for WMA codecs so that we know
the codec profile present and tell DSP accordingly, so update this API
to pass the codec profile as argument
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200316055221.1944464-4-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Some WMA decoders like WMAv10 etc need some additional encoder option
parameters, so add these as WMA decoder params.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200316055221.1944464-3-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Some codec profiles were missing for WMA, like WMA9/10 lossless and
wma10 pro, so add these profiles
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200316055221.1944464-2-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Broadcom DSL/PON SoC audio driver
with Whistler I2S block. The SoC supported by this
patch are BCM63158B0,BCM63178 and BCM47622/6755
Signed-off-by: Kevin Li <kevin-ke.li@broadcom.com>
Link: https://lore.kernel.org/r/20200312223242.2843-2-kevin-ke.li@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We've removed GFP_ATOMIC in all machine drivers and somehow this keeps
coming back due to copy-paste. Move to GFP_KERNEL.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200312194859.4051-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Maxim MAX98360A plug-and-play Class-D amplifier support on SSP1,
new card ID is sofda7219max98360a, name sof-da7219max98360a.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312194859.4051-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix a clumsy structure member dereference in all machine drivers.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312194859.4051-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Variables, used as loop iterators, don't need to be initialised.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312194859.4051-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To help user-space with HDMI codec driver transition, both
a kernel module parameter and a kernel option were initially
provided to configure default behaviour of SOF on Intel hardware
with commit 139c7febad ("ASoC: SOF: Intel: add support for
snd-hda-codec-hdmi").
As hdac-hdmi is already now lagging in features compared to
snd-hda-codec-hdmi, move ahead with the transition and remove
the build option to select between the two, and instead default
to snd-hda-codec-hdmi if it is enabled in kernel build.
The old behaviour of using hdac-hdmi driver can still be forced
via the kernel module parameter.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312194859.4051-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make HDMI optional for APL and later platforms. If no HDMI codec
is found on the HDA bus, the graphics side driver is missing or
correct codec driver is not part of kernel build, codec_mask
reflects this and HDMI is disabled. The DSP topology will still
have the links for HDMI, so connect these to dummy codec to avoid
failures in topology loading.
This change also fixes a kernel oops that was triggered if
sof_pcm512x was used with SOF configured to use hdac-hdmi (can be
done via "use_common_hdmi=0" or by selecting
CONFIG_SND_SOC_SOF_HDA_COMMON_HDMI_CODEC=n). This is not a supported
configuration.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312194859.4051-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Having a reverse dependency to a config that has its own additional
dependencies, is generally not recommended. And this applies to
select statements for SND_HDA_CODEC_HDMI, e.g. the case where SND_HDA
and SND_SOC_SOF_HDA are built as modules, but the machine driver is
built-in, leading to compile errors (reported as
i386-randconfig-e003-20200206).
Give up on trying to define different dependencies based on SOF/SST
selection, and simply add a "depends on" for SND_HDA_CODEC_HDMI. This
fixes the issue with randconfigs. Only downside is that SND_HDA_CODEC_HDMI
may be built unnecessarily in some cases, but this seems like the lesser
evil.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312194859.4051-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Having a reverse dependency to a config that has its own additional
dependencies, is generally not recommended. And this applies to
select statements for SND_HDA_CODEC_HDMI, e.g. the case where SND_HDA
and SND_SOC_SOF_HDA are built as modules, but the machine driver is
built-in, leading to compile errors (reported as
i386-randconfig-e003-20200206).
Give up on trying to define different dependencies based on SOF/SST
selection, and simply add a "depends on" for SND_HDA_CODEC_HDMI. This
fixes the issue with randconfigs. Only downside is that SND_HDA_CODEC_HDMI
may be built unnecessarily in some cases, but this seems like the lesser
evil.
Fixes: aa2b4a5 ('ASoC: Intel: boards: fix incorrect HDMI Kconfig dependency')
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312194859.4051-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend code from single cpu-dai to multi-dai
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312200622.24477-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The HDA_DSP_IPC_PURGE_FW IPC from ROM is already handled in
cl_dsp_init(), and it will never be received in the IRQ thread,
so the wait condition on this IPC will never be satisfied. The
wait before loading firmware is redundant and can be removed safely.
Signed-off-by: Amery Song <chao.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Keyon Jie <yang.jie@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200312200622.24477-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The HDA_DSP_IPC_PURGE_FW IPC from ROM is already handled in
cl_dsp_init(), and as IPC IRQ is disabled at this stage, this
IPC will be never received in the IRQ thread. The function
hda_dsp_ipc_is_sof for filtering the ROM IPC can be removed
safely.
Signed-off-by: Amery Song <chao.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Keyon <yang.jie@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200312200622.24477-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This enum code, and what's more important, related structures is
unused in whole source code, so it shouldn't be kept.
Signed-off-by: Karol Trzcinski <karolx.trzcinski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312200622.24477-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It's a part of ABI interface, so enum value shouldn't change
for example after removing some old enum code.
Signed-off-by: Karol Trzcinski <karolx.trzcinski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312200622.24477-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_stream_valid() will check if the stream is valid by testing
stream->channels_min. So we do need the information in dai driver.
The stream name is not added since we want to sure
playback_widget/capture_widget will be created by topology.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200312200622.24477-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snprintf() is a hard-to-use function, it's especially difficult to use
it for concatenating substrings in a buffer with a limited size.
Since snprintf() returns the would-be-output size, not the actual
size, the subsequent use of snprintf() may point to the incorrect
position.
Use scnprintf() instead for fixing such potential errors.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200313130334.9028-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Function soc_tplg_dbytes_create(), calls soc_tplg_init_kcontrol() to
perform additional driver specific initialization. While
soc_tplg_init_kcontrol() ensures that component is valid before invoking
ops->control_load, there is no such check at the end of
soc_tplg_dbytes_create() where list_add() is used.
Also in quite a few places, there is reference of tplg->comp->dapm or
tplg->comp->card, without any checks for tplg->comp.
In consequence of the above this may lead to referencing NULL pointer.
This allows for removal of now unnecessary checks.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20200312122239.14489-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Extra dtc warnings (roughly what W=1 enables) are now enabled by default
when building the binding examples. These were fixed treewide in
5.6-rc5, but the newly added google,cros-ec-codec schema adds some new
warnings:
Documentation/devicetree/bindings/sound/google,cros-ec-codec.example.dts:17.28-21.11:
Warning (unit_address_vs_reg): /example-0/reserved_mem: node has a reg or ranges property, but no unit name
Documentation/devicetree/bindings/sound/google,cros-ec-codec.example.dts:22.19-32.11:
Warning (unit_address_vs_reg): /example-0/cros-ec@0: node has a unit name, but no reg property
Documentation/devicetree/bindings/sound/google,cros-ec-codec.example.dts:26.37-31.15:
Warning (unit_address_vs_reg): /example-0/cros-ec@0/ec-codec: node has a reg or ranges property, but no unit name
Fixing the above, then results in:
Documentation/devicetree/bindings/sound/google,cros-ec-codec.example.dts:26.13-23:
Warning (reg_format): /example-0/cros-ec@0:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
Documentation/devicetree/bindings/sound/google,cros-ec-codec.example.dts:27.37-32.15:
Warning (unit_address_vs_reg): /example-0/cros-ec@0/ec-codec: node has a reg or ranges property, but no unit name
Fixes: eadd54c75f ("dt-bindings: Convert the binding file google, cros-ec-codec.txt to yaml format.")
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: alsa-devel@alsa-project.org
Cc: Benson Leung <bleung@chromium.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Link: https://lore.kernel.org/r/20200311205841.2710-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes DPCM runtime update functions available for external
calling. As an example, virtualised ASoC component drivers may need
to call these when managing shared DAPM routes that are used by more
than one driver (i.e. when host driver and guest drivers have a DAPM
path from guest PCM to host DAI where some parts are owned by host
driver and others by guest driver).
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200312095214.15126-3-guennadi.liakhovetski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently dpcm_prune_paths() has up to 4 nested condition and loop
levels, which forces the code to use flags for flow control.
Extracting widget status verification code from dpcm_prune_paths()
into a separate function simplifies the code.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200312095214.15126-2-guennadi.liakhovetski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
QDSP6 Frontend dais can be configured to work in rx or tx or both rx/tx mode,
however the default routing do not honour this DT configuration making sound
card fail to probe. FE dais are also not fully honouring device tree configuration.
Fix both of them.
Originally issue was reported by Vinod Koul
Srinivas Kandagatla (2):
ASoC: qdsp6: q6asm-dai: only enable dais from device tree
ASoC: qdsp6: q6routing: remove default routing
sound/soc/qcom/qdsp6/q6asm-dai.c | 30 +++++++++++++++++++++++-------
sound/soc/qcom/qdsp6/q6routing.c | 19 -------------------
2 files changed, 23 insertions(+), 26 deletions(-)
--
2.21.0
