IEEE 802.1Q says that when we receive priority-tagged (VID 0) frames
use the PVID for the port as its VID.
(See IEEE 802.1Q-2011 6.9.1 and Table 9-2)
Apply the PVID to not only untagged frames but also priority-tagged frames.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.1Q says that:
- VID 0 shall not be configured as a PVID, or configured in any Filtering
Database entry.
- VID 4095 shall not be configured as a PVID, or transmitted in a tag
header. This VID value may be used to indicate a wildcard match for the VID
in management operations or Filtering Database entries.
(See IEEE 802.1Q-2011 6.9.1 and Table 9-2)
Don't accept adding these VIDs in the vlan_filtering implementation.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit be4f154d5e
bridge: Clamp forward_delay when enabling STP
had a typo when attempting to clamp maximum forward delay.
It is possible to set bridge_forward_delay to be higher then
permitted maximum when STP is off. When turning STP on, the
higher then allowed delay has to be clamed down to max value.
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Reviewed-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_can_gso() should only be used as a hint in tcp_sendmsg() to build GSO
packets in the first place. (As a performance hint)
Once we have GSO packets in write queue, we can not decide they are no
longer GSO only because flow now uses a route which doesn't handle
TSO/GSO.
Core networking stack handles the case very well for us, all we need
is keeping track of packet counts in MSS terms, regardless of
segmentation done later (in GSO or hardware)
Right now, if tcp_fragment() splits a GSO packet in two parts,
@left and @right, and route changed through a non GSO device,
both @left and @right have pcount set to 1, which is wrong,
and leads to incorrect packet_count tracking.
This problem was added in commit d5ac99a648 ("[TCP]: skb pcount with MTU
discovery")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP stack should make sure it owns skbs before mangling them.
We had various crashes using bnx2x, and it turned out gso_size
was cleared right before bnx2x driver was populating TC descriptor
of the _previous_ packet send. TCP stack can sometime retransmit
packets that are still in Qdisc.
Of course we could make bnx2x driver more robust (using
ACCESS_ONCE(shinfo->gso_size) for example), but the bug is TCP stack.
We have identified two points where skb_unclone() was needed.
This patch adds a WARN_ON_ONCE() to warn us if we missed another
fix of this kind.
Kudos to Neal for finding the root cause of this bug. Its visible
using small MSS.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull this batch of fixes intended for the 3.12 stream!
For the mac80211 bits, Johannes says:
"Jouni fixes a remain-on-channel vs. scan bug, and Felix fixes client TX
probing on VLANs."
And also:
"This time I have two fixes from Emmanuel for RF-kill issues, and fixed
two issues reported by Evan Huus and Thomas Lindroth respectively."
On top of those...
Avinash Patil adds a couple of mwifiex fixes to properly inform cfg80211
about some different types of disconnects, avoiding WARNINGs.
Mark Cave-Ayland corrects a pointer arithmetic problem in rtlwifi,
avoiding incorrect automatic gain calculations.
Solomon Peachy sends a cw1200 fix for locking around calls to
cw1200_irq_handler, addressing "lost interrupt" problems.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a QMI device, manufactured by TCT Mobile Phones.
A companion patch blacklisting this device's QMI interface in the option.c
driver has been sent.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Antonella Pellizzari <anto.pellizzari83@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to schedule the refill work unconditionally after changing the
number of queues. This may lead an issue if the device is not
up. Since we only try to cancel the work in ndo_stop(), this may cause
the refill work still work after removing the device. Fix this by only
schedule the work when device is up.
The bug were introduce by commit 9b9cd8024a.
(virtio-net: fix the race between channels setting and refill)
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're trying to re-configure the affinity unconditionally in cpu hotplug
callback. This may lead the issue during resuming from s3/s4 since
- virt queues haven't been allocated at that time.
- it's unnecessary since thaw method will re-configure the affinity.
Fix this issue by checking the config_enable and do nothing is we're not ready.
The bug were introduced by commit 8de4b2f3ae
(virtio-net: reset virtqueue affinity when doing cpu hotplug).
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We overwrite the ->bitrate with the user supplied information on the
next line.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cap bitrate at YAM_MAXBITRATE in yam_ioctl(), but it could also be
negative. I don't know the impact of using a negative bitrate but let's
prevent it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If interrupts happen before napi_enable was called, the driver will not
work as expected. Network transmissions are impossible in this state.
This bug can be reproduced easily by restarting the network interface in
a loop. After some time any network transmissions on the network
interface will fail.
This patch fixes the bug by enabling napi before enabling the network
interface interrupts.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RPS support is kind of broken on bnx2x, because only non LRO packets
get proper rx queue information. This triggers reorders, as it seems
bnx2x like to generate a non LRO packet for segment including TCP PUSH
flag : (this might be pure coincidence, but all the reorders I've
seen involve segments with a PUSH)
11:13:34.335847 IP A > B: . 415808:447136(31328) ack 1 win 457 <nop,nop,timestamp 3789336 3985797>
11:13:34.335992 IP A > B: . 447136:448560(1424) ack 1 win 457 <nop,nop,timestamp 3789336 3985797>
11:13:34.336391 IP A > B: . 448560:479888(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985797>
11:13:34.336425 IP A > B: P 511216:512640(1424) ack 1 win 457 <nop,nop,timestamp 3789337 3985798>
11:13:34.336423 IP A > B: . 479888:511216(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985798>
11:13:34.336924 IP A > B: . 512640:543968(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985798>
11:13:34.336963 IP A > B: . 543968:575296(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985798>
We must call skb_record_rx_queue() to properly give to RPS (and more
generally for TX queue selection on forward path) the receive queue
information.
Similar fix is needed for skb_mark_napi_id(), but will be handled
in a separate patch to ease stable backports.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On receiving an ACK that covers the loss probe sequence, TLP
immediately sets the congestion state to Open, even though some packets
are not recovered and retransmisssion are on the way. The later ACks
may trigger a WARN_ON check in step D of tcp_fastretrans_alert(), e.g.,
https://bugzilla.redhat.com/show_bug.cgi?id=989251
The fix is to follow the similar procedure in recovery by calling
tcp_try_keep_open(). The sender switches to Open state if no packets
are retransmissted. Otherwise it goes to Disorder and let subsequent
ACKs move the state to Recovery or Open.
Reported-By: Michael Sterrett <michael@sterretts.net>
Tested-By: Dormando <dormando@rydia.net>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -ENOMEM in the padding pkt alloc fail error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich says:
====================
sctp: Use software checksum under certain circumstances.
There are some cards that support SCTP checksum offloading. When using
these cards with IPSec or forcing IP fragmentation of SCTP traffic,
the checksum is computed incorrectly due to the fact that xfrm and IP/IPv6
fragmentation code do not know that this is SCTP traffic and do not
know that checksum has to be computed differently.
To fix this, we let SCTP detect these conditions and perform software
checksum calculation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
IP/IPv6 fragmentation knows how to compute only TCP/UDP checksum.
This causes problems if SCTP packets has to be fragmented and
ipsummed has been set to PARTIAL due to checksum offload support.
This condition can happen when retransmitting after MTU discover,
or when INIT or other control chunks are larger then MTU.
Check for the rare fragmentation condition in SCTP and use software
checksum calculation in this case.
CC: Fan Du <fan.du@windriver.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb/ixgbe have hardware sctp checksum support, when this feature is enabled
and also IPsec is armed to protect sctp traffic, ugly things happened as
xfrm_output checks CHECKSUM_PARTIAL to do checksum operation(sum every thing
up and pack the 16bits result in the checksum field). The result is fail
establishment of sctp communication.
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dst->xfrm is conditionally defined. Provide accessor funtion that
is always available.
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikita Kiryanov says:
====================
dm9000 improvements
This is a collection of improvements and bug fixes for dm9000, mostly
related to its startup and resume-from-suspend sequences.
Patch "Implement full reset of DM9000 network device" was submitted to the
linux-kernel mailing list but never applied.
An archive of the submission and the following conversation can be found here:
http://lkml.indiana.edu/hypermail/linux/kernel/1205.2/02817.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the LPA by checking mii_if_info, instead of just saying "no LPA" every
time.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Davicom application note for the DM9000 network device recommends
performing software reset twice to correctly initialise the device.
Without this reset some devices fail to initialise correctly on
system startup.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take the phy out of reset explicitly during system resume to avoid
losing network connectivity.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the changes introduced in commit 6741f40 (DM9000B: driver
initialization upgrade) break functionality on DM9000A
(error message during NFS boot: "dm9000 dm9000.0: eth0: link down")
Since the changes were meant to serve only DM9000B, make them
dependent on the chip type.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds missing cfg80211_disconnected event for P2P client
interface upon successful deauthenticate command, deauthenticate
event or disassociate event from FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If device is surprise removed, commands sent to FW including
deauthenticate command fail as bus writes fail.
We update our media_connected status to false and inform cfg80211
about disconnection only when command is successful. Since cfg80211
assumes device is still connected, it results into following
WARN_ON during unload:
WARNING: CPU: 0 PID: 18245 at net/wireless/core.c:937
cfg80211_netdev_notifier_call+0x175/0x4d0 [cfg80211]()
Avoid this by emitting cfg80211_disconnected event even if the
deauthenticate command fails.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a frame's timestamp is calculated, and the bitrate
calculation goes wrong and returns zero, the system
will attempt to divide by zero and crash. Catch this
case and print the rate information that the driver
reported when this happens.
Cc: stable@vger.kernel.org
Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When parsing an invalid radiotap header, the parser can overrun
the buffer that is passed in because it doesn't correctly check
1) the minimum radiotap header size
2) the space for extended bitmaps
The first issue doesn't affect any in-kernel user as they all
check the minimum size before calling the radiotap function.
The second issue could potentially affect the kernel if an skb
is passed in that consists only of the radiotap header with a
lot of extended bitmaps that extend past the SKB. In that case
a read-only buffer overrun by at most 4 bytes is possible.
Fix this by adding the appropriate checks to the parser.
Cc: stable@vger.kernel.org
Reported-by: Evan Huus <eapache@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SMC_outw invokes an endian-aware I/O accessor, which may change the data
endianness before writing to the device. This is not suitable for data
transfers where the memory buffer is simply a string of bytes that does
not require any byte-swapping.
This patches fixes the smc91x SMC_PUSH_DATA macro so that it uses the
string I/O accessor for outputting the leading or trailing halfwords on
halfword-aligned buffers.
Cc: <netdev@vger.kernel.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fst_get_iface() code fails to initialize the two padding bytes of
struct sync_serial_settings after the ->loopback member. Add an explicit
memset(0) before filling the structure to avoid the info leak.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6_tnl.hlen (gre and ipv6 headers length) is independent from the
outgoing interface, so it would be better to initialize it even when no
route is found, otherwise its value will be zero.
While I'm not sure if this could happen in real life, but doing that
will avoid to call the skb_push function with a zero in ip6gre_header
function.
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Oussama Ghorbel <ou.ghorbel@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netem can leak memory because packets get stored in red-black
tree and it is not cleared on reset.
Reported by: Сергеев Сергей <adron@yapic.net>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When packet is dropped from rb-tree netem the backlog statistic should
also be updated.
Reported-by: Сергеев Сергей <adron@yapic.net>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nguyen Hong Ky posted a patch to correct RX packet errors on R8A7740 which
was applied as 2c6221e4a5 ("net: sh_eth: Fix RX packets errors on
R8A7740"). Unfortunately sh_eth.c contains many similar instances
of struct sh_eth_cpu_data and the patch was miss-applied, updating
sh7734_data instead of r8a7740_data.
This patch corrects this problem by.
1. Reverting the change to sh7734_data and;
2. Applying the change to r8a7740_data.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes and improves the use of vti interfaces (while
lightly changing the way of configuring them).
Currently:
- it is necessary to identify and mark inbound IPsec
packets destined to each vti interface, via netfilter rules in
the mangle table at prerouting hook.
- the vti module cannot retrieve the right tunnel in input since
commit b9959fd3: vti tunnels all have an i_key, but the tunnel lookup
is done with flag TUNNEL_NO_KEY, so there no chance to retrieve them.
- the i_key is used by the outbound processing as a mark to lookup
for the right SP and SA bundle.
This patch uses the o_key to store the vti mark (instead of i_key) and
enables:
- to avoid the need for previously marking the inbound skbuffs via a
netfilter rule.
- to properly retrieve the right tunnel in input, only based on the IPsec
packet outer addresses.
- to properly perform an inbound policy check (using the tunnel o_key
as a mark).
- to properly perform an outbound SPD and SAD lookup (using the tunnel
o_key as a mark).
- to keep the current mark of the skbuff. The skbuff mark is neither
used nor changed by the vti interface. Only the vti interface o_key
is used.
SAs have a wildcard mark.
SPs have a mark equal to the vti interface o_key.
The vti interface must be created as follows (i_key = 0, o_key = mark):
ip link add vti1 mode vti local 1.1.1.1 remote 2.2.2.2 okey 1
The SPs attached to vti1 must be created as follows (mark = vti1 o_key):
ip xfrm policy add dir out mark 1 tmpl src 1.1.1.1 dst 2.2.2.2 \
proto esp mode tunnel
ip xfrm policy add dir in mark 1 tmpl src 2.2.2.2 dst 1.1.1.1 \
proto esp mode tunnel
The SAs are created with the default wildcard mark. There is no
distinction between global vs. vti SAs. Just their addresses will
possibly link them to a vti interface:
ip xfrm state add src 1.1.1.1 dst 2.2.2.2 proto esp spi 1000 mode tunnel \
enc "cbc(aes)" "azertyuiopqsdfgh"
ip xfrm state add src 2.2.2.2 dst 1.1.1.1 proto esp spi 2000 mode tunnel \
enc "cbc(aes)" "sqbdhgqsdjqjsdfh"
To avoid matching "global" (not vti) SPs in vti interfaces, global SPs
should no use the default wildcard mark, but explicitly match mark 0.
To avoid a double SPD lookup in input and output (in global and vti SPDs),
the NOPOLICY and NOXFRM options should be set on the vti interfaces:
echo 1 > /proc/sys/net/ipv4/conf/vti1/disable_policy
echo 1 > /proc/sys/net/ipv4/conf/vti1/disable_xfrm
The outgoing traffic is steered to vti1 by a route via the vti interface:
ip route add 192.168.0.0/16 dev vti1
The incoming IPsec traffic is steered to vti1 because its outer addresses
match the vti1 tunnel configuration.
Signed-off-by: Christophe Gouault <christophe.gouault@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 9f00b2e7cf
bridge: only expire the mdb entry when query is received
changed the mdb expiration timer to be armed only when QUERY is
received. Howerver, this causes issues in an environment where
the multicast server socket comes and goes very fast while a client
is trying to send traffic to it.
The root cause is a race where a sequence of LEAVE followed by REPORT
messages can race against QUERY messages generated in response to LEAVE.
The QUERY ends up starting the expiration timer, and that timer can
potentially expire after the new REPORT message has been received signaling
the new join operation. This leads to a significant drop in multicast
traffic and possible complete stall.
The solution is to have REPORT messages update the expiration timer
on entries that already exist.
CC: Cong Wang <xiyou.wangcong@gmail.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes "lost interrupt" problems that occurred on SPI-based systems.
cw1200_irq_handler() expects the hwbus to be locked, but on the
SPI-path, that lock wasn't taken (unlike in the SDIO-path, where the
generic SDIO-code takes care of acquiring the lock).
Cc: stable@vger.kernel.org
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An error in calculating the offset in an skb causes the driver to read
essential device info from the wrong locations. The main effect is that
automatic gain calculations are nonsense.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [2.6.39+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit:
3078cde7 can: at91_can: add dt support
device tree support was added to the at91_can driver. In this commit the
mapping of device to driver data was mixed up. This results in the sam9x5
parameters being used for the sam9263 and the workaround for the broken mailbox
0 on the sam9263 not being activated.
This patch fixes the broken platform_device_id table.
Cc: linux-stable <stable@vger.kernel.org>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The current implemetation of of_match_device() relies that the of_device_id
table in the driver is sorted from most specific to least specific compatible.
Without this patch the mx28 is detected as the less specific p1010. This leads
to a p1010 specific workaround is activated on the mx28, which is not needed.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In patch
0d1862e can: flexcan: fix flexcan_chip_start() on imx6
the loop in flexcan_chip_start() that iterates over all mailboxes after the
soft reset of the CAN core was removed. This loop put all mailboxes (even the
ones marked as reserved 1...7) into EMPTY/INACTIVE mode. On mailboxes 8...63,
this aborts any pending TX messages.
After a cold boot there is random garbage in the mailboxes, which leads to
spontaneous transmit of CAN frames during first activation. Further if the
interface was disabled with a pending message (usually due to an error
condition on the CAN bus), this message is retransmitted after enabling the
interface again.
This patch fixes the regression by:
1) Limiting the maximum number of used mailboxes to 8, 0...7 are used by the RX
FIFO, 8 is used by TX.
2) Marking the TX mailbox as EMPTY/INACTIVE, so that any pending TX of that
mailbox is aborted.
Cc: linux-stable <stable@vger.kernel.org>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
John W. Linville says:
===================
Please pull this batch of fixes intended for 3.12...
Most of the bits are for iwlwifi -- Johannes says:
"I have a fix for WoWLAN/D3, a PCIe device fix, we're removing a
warning, there's a fix for RF-kill while scanning (which goes together
with a mac80211 fix) and last but not least we have many new PCI IDs."
Also for iwlwifi is a patch from Johannes to correct some merge damage
that crept into the tree before the last merge window.
On top of that, Felix Fietkau sends an ath9k patch to avoid a Tx
scheduling hang when changing channels to do a scan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable workaround for P2020/P2010 erratum eTSEC 20,
"Excess delays when transmitting TOE=1 large frames".
The impact is that frames lager than 2500-bytes for which
TOE (i.e. TCP/IP hw accelerations like Tx csum) is enabled
may see excess delay before start of transmission.
This erratum was fixed in Rev 2.0.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macros and defines from mpc85xx.h to simplify
and prevent errors in identifying a mpc85xx based SoC
for errata detection.
This should help enabling (and identifying) workarounds
for various mpc85xx based chips and revisions.
For instance, express MPC8548 Rev.2 as:
(SVR_SOC_VER(svr) == SVR_8548) && (SVR_REV(svr) == 0x20)
instead of:
(pvr == 0x80210020 && mod == 0x8030 && rev == 0x0020)
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A002 is still in "no plans to fix" state, and applies to all
the current P1/P2 parts as well, so it's resonable to enable
its workaround by default, for all the soc's with etsec.
The impact of not enabling this workaround for affected parts
is that under certain conditons (runt frames or even frames
with RX error detected at PHY level) during controller reset,
the controller might fail to indicate Rx reset (GRS) completion.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
