The GPU has two functional clocks - GPU_CORE_GCLK and GPU_HYD_GCLK.
Both of these are mux clocks and are derived from the DPLL_CORE
H14 output clock CORE_GPU_CLK by default. These clocks can also be
be derived from DPLL_PER or DPLL_GPU.
The GPU DPLL provides the output clocks primarily for the GPU.
Configuring the GPU for different OPP clock frequencies is easier
to achieve when using the DPLL_GPU rather than the other two DPLLs
due to:
1. minimal affect on any other output clocks from these DPLLs
2. may require an impossible post-divider values on existing DPLLs
without affecting other clocks.
So, switch the GPU functional clocks to be sourced from GPU DPLL by
default. This is done using the DT standard properties "assigned-clocks"
and "assigned-clock-parents". Newer u-boots (from 2017.01 onwards) reuse
and can update these properties to choose an appropriate one-time fixed
OPP configuration as all the required ABB/AVS setup is performed within
the bootloader. Note that there is no DVFS supported for any of the
non-MPU domains. The DPLL will automatically transition into a low-power
stop mode when the associated output clocks are not utilized or gated
automatically.
This patch also sets the initial values for the DPLL_GPU outputs.
These values are chosen based on the OPP_NOM values defined as per
recommendation from design team. The DPLL locked frequency is kept
at 1277 MHz, so that the value for the divider clock, dpll_gpu_m2_ck,
can be set to 425.67 MHz for OPP_NOM.
Signed-off-by: Subhajit Paul <subhajit_paul@ti.com>
[s-anna@ti.com: revise patch description]
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IVA DPLL in DRA7xx provides the output clocks for only the IVAHD
subsystem in DRA7xx as compared to previous OMAP generations when it
provided the clocks for both DSP and IVAHD subsystems. This DPLL is
currently not configured by older bootloaders. Use the DT standard
properties "assigned-clocks" and "assigned-clock-rates" to set the
IVA DPLL clock rate and the rates for its derivative clocks at boot
time to properly initialize/lock this DPLL and be independent of the
bootloader version. Newer u-boots (from 2017.01 onwards) reuse and
can update these properties to choose an appropriate one-time fixed
OPP configuration. The DPLL will automatically transition into a
low-power stop mode when the associated output clocks are not
utilized or gated automatically.
The reset value of the divider M2 (that supplies the IVA_GFLCK, the
functional clock for the IVAHD subsystem) does not match a specific
OPP. So, the derived output clock from this IVA DPLL has to be
initialized as well to avoid initializing these divider outputs to an
incorrect frequencies.
The OPP_NOM clock frequencies are defined in the AM572x SR2.0 Data
Sheet vB, section 5.5.2 "Voltage And Core Clock Specifications". The
clock rates are chosen based on these OPP_NOM values and defined as per
a DRA7xx PLL spec document. The DPLL locked frequency is 2300 MHz, so
the dpll_iva_ck clock rate used is half of this value. The value for the
divider clock, dpll_iva_m2_ck, has to be set to 388.333334 MHz or more
for the divider clk logic to compute the appropriate divider value for
OPP_NOM.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DSP DPLL is a new DPLL compared to previous OMAP generations and
supplies the root clocks for the DSP processors, as well as a mux
input source for EVE sub-system (on applicable SoCs). This DPLL is
currently not configured by older bootloaders. Use the DT standard
properties "assigned-clocks" and "assigned-clock-rates" to set the
DSP DPLL clock rate and the rates for its derivative clocks at boot
time to properly initialize/lock this DPLL and be independent of the
bootloader version. Newer u-boots (from 2017.01 onwards) reuse and
can update these properties to choose an appropriate one-time fixed
OPP configuration. The DPLL will automatically transition into a
low-power stop mode when the associated output clocks are not
utilized or gated automatically.
The DSP DPLL provides two output clocks, DSP_GFCLK and EVE_GCLK. The
desired rate for DSP_GFCLK is 600 MHz (same as DSP DPLL CLKOUT frequency),
and is currently auto set due to the desired M2 divider value being the
same as reset value for the locked frequency of 600 MHz. The EVE_GCLK
however is required to be 400 MHz, so set the dpll_dsp_m3x2_ck's rate
explicitly so that the divider is set properly. The dpll_dsp_m2_ck rate
is also set explicitly to not rely on any implicit matching divider reset
values to the locked DPLL frequency.
The OPP_NOM clock frequencies are defined in the AM572x SR2.0 Data
Sheet vB, section 5.5.2 "Voltage And Core Clock Specifications". The
clock rates are chosen based on these OPP_NOM values and defined as per
a DRA7xx PLL spec document. The DPLL locked frequency is 1200 MHz, so
the dpll_dsp_ck clock rate used is half of this value.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IPU1 functional clock is actually the output of a mux clock,
ipu1_gfclk_mux. The mux clock is sourced by default from the
DPLL_ABE_X2_CLK, and this results in a rather odd clock frequency
(361 MHz) for the IPU1 functional clock on platforms where ABE_DPLL
is configured properly. Reconfigure the mux clock to be sourced from
CORE_IPU_ISS_BOOST_CLK (dpll_core_h22x2_ck), so that both the IPU1
and IPU2 are running from the same clock and clocked at the same
nominal frequency of 425 MHz.
This also ensures that IPU1 functional clock is always configured
properly and becomes independent of the state of the ABE DPLL on
all boards.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IVA DPLL is not an essential DPLL for the functionality of a
bootloader and is usually not configured (e.g. older u-boots configure
it only if CONFIG_SYS_CLOCKS_ENABLE_ALL is enabled and u-boots newer
than 2014.01 do not even have an option), and this results in incorrect
operating frequencies when trying to use a DSP or IVAHD, whose root
clocks are derived from this DPLL. Use the DT standard properties
"assigned-clocks" and "assigned-clock-rates" to set the IVA DPLL clock
rate and the rates for its derivative clocks at boot time to properly
initialize/lock this DPLL. The DPLL will automatically transition
into a low-power stop mode when the associated output clocks are
not utilized or gated automatically.
The reset values of the dividers H11 & H12 (functional clocks for DSP
and IVAHD respectively) are identical to each other, but are different
at each OPP. The reset values also do not match a specific OPP. So, the
derived output clocks from the IVA DPLL have to be initialized as well
to avoid initializing these divider outputs to incorrect frequencies.
The clock rates are chosen based on the OPP_NOM values as defined in
the OMAP5432 SR2.0 Data Manual Book vK, section 5.2.3.5 "DPLL_IVA
Preferred Settings". The recommended maximum DPLL locked frequency is
2330 MHz for OPP_NOM (value for DPLL_IVA_X2_CLK), so the dpll_iva_ck
clock rate used is half of this value. The value 465.92 MHz is used
instead of 465.9 MHz for dpll_iva_h11x2_ck so that proper divider
value can be calculated.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IVA DPLL is not an essential DPLL for the functionality of a
bootloader and is usually not configured (e.g. older u-boots configure
it only if CONFIG_SYS_CLOCKS_ENABLE_ALL is enabled and u-boots newer
than 2014.01 do not even have an option), and this results in incorrect
operating frequencies when trying to use a DSP or IVAHD, whose root
clocks are derived from this DPLL. Use the DT standard properties
"assigned-clocks" and "assigned-clock-rates" to set the IVA DPLL clock
rate and the rates for its derivative clocks at boot time to properly
initialize/lock this DPLL. The DPLL will automatically transition
into a low-power stop mode when the associated output clocks are
not utilized or gated automatically.
The reset values of the dividers M4 & M5 (functional clocks for DSP and
IVAHD respectively) are identical to each other, but are different at
each OPP. The reset values also do not match a specific OPP. So, the
derived output clocks from the IVA DPLL have to be initialized as well
to avoid initializing these divider outputs to incorrect frequencies.
The clock rates are chosen based on the OPP100 values as defined in the
OMAP4430 ES2.x Public TRM vAP, section "3.6.3.8.7 DPLL_IVA Preferred
Settings". The DPLL locked frequency is 1862.4 MHz (value for
DPLL_IVA_X2_CLK), so the dpll_iva_ck clock rate used is half of
this value.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The bogus 'device_type = "pci"' confuses dtc, causing lots of totally
unrelated warnings. After fixing that, real warnings like
arch/arm/boot/dts/r8a7790-lager.dtb: Warning (pci_device_reg): Node /pci@ee090000/usb@0,1 PCI unit address format error, expected "1,0"
are left. Correct the unit-addresses and reg properties of the subnodes
to fix these.
Signed-off-by: Rob Herring <robh@kernel.org>
[geert: Improve description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for iWave RainboW-G20D-Qseven board based on RZ/G1M.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for iWave RZG1M Qseven System On Module.
http://www.iwavesystems.com/rz-g1m-qseven-module.html
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device tree source for Renesas GR-Peach board.
GR-Peach is an RZ/A1H based board with 10MB of on-chip SRAM and 8MB
QSPI flash storage.
Add support for the board, and create a 2MB partition to use as rootfs.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This merges the Moxa Art timer driver into the Faraday FTTMR010
driver and replaces all Kconfig symbols to use the Faraday
driver instead. We are now so similar that the drivers can
be merged by just adding a few lines to the Faraday timer.
Differences:
- The Faraday driver explicitly sets the counter to count
upwards for the clocksource, removing the need for the
clocksource core to invert the value.
- The Faraday driver also handles sched_clock()
On the Aspeed, the counter can only count downwards, so support
the timers in downward-counting mode as well, and flag the
Aspeed to use this mode. This mode was tested on the Gemini so
I have high hopes that it'll work fine on the Aspeed as well.
After this we have one driver for all three SoCs and a generic
Faraday FTTMR010 timer driver, which is nice.
Cc: Joel Stanley <joel@jms.id.au>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The merging of a number of clocksource drivers into fttmr010 means we
require clock-names to be specified in the Aspeed timer node, else the
clocksource fails to probe and boot hangs.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Motorola Droid 4 uses a WL1285C, so use proper compatible value.
To avoid regressions while support for the new compatible value
is added to the Linux kernel, the old compatible value is preserved
as fallback.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Droid 4 has a isl29030 to measure ambient light (e.g. for
automatically adapting display brightness) and proximity.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Generate new defconfig to get rid of obsolete Kconfig entries:
- BUGVERBOSE was changed into DEBUG_BUGVERBOSE and will be enabled by
default (it is useful);
- DETECT_SOFTLOCKUP was changed into LOCKUP_DETECTOR;
- rest of entries is being removed by default values;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Generate new defconfig to get rid of obsolete Kconfig entries:
- S3C_LOWLEVEL_UART_PORT and S3C_DEV_FB are invalid for S5P;
- S5PV210_SETUP_FB_24BPP is gone;
- rest of entries is being removed by default values;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Generate new defconfig to get rid of obsolete Kconfig entries:
- S3C_BOOT_ERROR_RESET, SND_S3C24XX_SOC and SND_SOC_SMDK_WM9713 are
gone;
- rest of entries is being removed by default values;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Generate new defconfig to get rid of obsolete Kconfig entries:
- NET_ETHERNET, SND_S3C24XX_SOC are gone;
- CRYPTO_FIPS is changed to no (cannot be part of module);
- BINFMT_AOUT cannot be selected anymore;
- rest of entries is being removed by default values;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Generate new defconfig to get rid of obsolete Kconfig entries:
- S3C_BOOT_ERROR_RESET, SMDK2440_CPU2442 are gone;
- ARM_THUMB is changed to yes (selected by default);
- BINFMT_AOUT cannot be selected anymore;
- rest of entries is being removed by default values;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Generate new defconfig to get rid of obsolete Kconfig entries:
- RFKILL_REGULATOR is gone;
- COMMON_CLK_MAX77802 was merged into COMMON_CLK_MAX77686;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The config was not updated for some time so it needs updates to get the
same options as wanted initially:
- SYSFS_DEPRECATED is now needed for SYSFS_DEPRECATED_V2;
- DEBUG_SPINLOCK_SLEEP was replaced by DEBUG_ATOMIC_SLEEP;
- Use proper DEBUG_S3C_UART1 for UART1;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The config was not updated for some time so it needs updates to get the
same options as wanted initially:
- SYSFS_DEPRECATED is now needed for SYSFS_DEPRECATED_V2;
- PWM is now needed for BACKLIGHT_PWM;
- DEBUG_SPINLOCK_SLEEP was replaced by DEBUG_ATOMIC_SLEEP;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The config was not updated for some time so it needs updates to get the
same options as wanted initially:
- IP_NF_TARGET_LOG was replaced by NETFILTER_XT_TARGET_LOG;
- NF_NAT was replaced by IP_NF_NAT;
- SERIAL_DEV_BUS is now needed for BT_HCIUART_LL;
- TPS65010 is now needed for MACH_OSIRIS_DVS;
- DMADEVICES and S3C24XX_DMAC are now needed for MMC_S3C;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The config was not updated for some time so it needs updates to get the
same options as wanted initially:
- SYSFS_DEPRECATED is now needed for SYSFS_DEPRECATED_V2;
- USB_GADGET_S3C2410 was replaced by USB_S3C2410;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The config was not updated for some time so it needs updates to get the
same options as wanted initially:
- SERIAL_DEV_BUS is now needed for BT_HCIUART_LL;
- USB_GADGET_S3C2410 was replaced by USB_S3C2410;
- S3C24XX_DMAC is now needed for MMC_S3C;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Re-order entries just like savedefconfig would do so it will be easier
to review the changes before actual savedefconfig.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Commit 71d1e5d71c ("arm: ecard: use dev_groups and not dev_attrs for bus_type")
had a typo in the resource attribute definition. Fix that up.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 71d1e5d71c ("arm: ecard: use dev_groups and not dev_attrs for bus_type")
Cc: Russell King <linux@armlinux.org.uk>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
The Orange Pi Plus 2E, unlike the Orange Pi PC and PC Plus which its
schematics are based on, uses an external Realtek RTL8211E PHY in
RGMII mode, with a GPIO enabling the regulator for I/O signalling
power supplies. The PHY's main power supply is enabled by the main
5V power supply.
Add the regulator and PHY nodes, and override the PHY phandle under
the EMAC node, so that the EMAC works properly on this board.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Including:
* Another compile-fix for my header cleanup
* A couple of fixes for the recently merged IOMMU probe
deferal code
* Includes fixes for ACPI/IORT code necessary with
IOMMU probe deferal
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6dZB
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v4.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- another compile-fix for my header cleanup
- a couple of fixes for the recently merged IOMMU probe deferal code
- fixes for ACPI/IORT code necessary with IOMMU probe deferal
* tag 'iommu-fixes-v4.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
arm: dma-mapping: Reset the device's dma_ops
ACPI/IORT: Move the check to get iommu_ops from translated fwspec
ARM: dma-mapping: Don't tear down third-party mappings
ACPI/IORT: Ignore all errors except EPROBE_DEFER
iommu/of: Ignore all errors except EPROBE_DEFER
iommu/of: Fix check for returning EPROBE_DEFER
iommu/dma: Fix function declaration
This removes the dummy clk81 gate and replaces it with the actual clock
controller's CLKID_CLK81. This will also allow us to pass the real clock
IDs to all devices where the clock is controlled by clkc in the future.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Select COMMON_CLK_MESON8B also for MACH_MESON8 since the Meson8b clock
controller driver can also be used on Meson8 SoCs now that we have a
separate compatible for it.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Been sitting on these for a couple of weeks waiting on some larger batches
to come in but it's been pretty quiet.
Just your garden variety fixes here:
- A few maintainers updates (ep93xx, Exynos, TI, Marvell)
- Some PM fixes for Atmel/at91 and Marvell
- A few DT fixes for Marvell, Versatile, TI Keystone, bcm283x
- A reset driver patch to set module license for symbol access
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WlSc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Been sitting on these for a couple of weeks waiting on some larger
batches to come in but it's been pretty quiet.
Just your garden variety fixes here:
- A few maintainers updates (ep93xx, Exynos, TI, Marvell)
- Some PM fixes for Atmel/at91 and Marvell
- A few DT fixes for Marvell, Versatile, TI Keystone, bcm283x
- A reset driver patch to set module license for symbol access"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: EP93XX: Update maintainership
MAINTAINERS: remove kernel@stlinux.com obsolete mailing list
ARM: dts: versatile: use #include "..." to include local DT
MAINTAINERS: add device-tree files to TI DaVinci entry
ARM: at91: select CONFIG_ARM_CPU_SUSPEND
ARM: dts: keystone-k2l: fix broken Ethernet due to disabled OSR
arm64: defconfig: enable some core options for 64bit Rockchip socs
arm64: marvell: dts: fix interrupts in 7k/8k crypto nodes
reset: hi6220: Set module license so that it can be loaded
MAINTAINERS: add irqchip related drivers to Marvell EBU maintainers
MAINTAINERS: sort F entries for Marvell EBU maintainers
ARM: davinci: PM: Do not free useful resources in normal path in 'davinci_pm_init'
ARM: davinci: PM: Free resources in error handling path in 'davinci_pm_init'
ARM: dts: bcm283x: Reserve first page for firmware
memory: atmel-ebi: mark PM ops as __maybe_unused
MAINTAINERS: Remove Javier Martinez Canillas as reviewer for Exynos
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add basic support for stm32h743i-discovery board
This board offers :
_ 2MBytes Flash
_ 1 x micro USB OTG port
_ 1 x STLink connector (micro USB)
_ 1 x micro SD card slot
_ 1 x RJ45 connector
_ 1 x RCA connector
_ 2 x Audio jack connectors (in and out)
_ 2 x speaker connectors (left and right)
_ 1 x joystick
_ 1 x DCMI connector (Digital camera interface)
_ 1 x 4 inch DSI LCD (Display Serial Interface)
_ Arduino Uno Connectors
_ 2 x PIO connectors (PMOD and PMOD+)
_ 1 x wakeup button
_ 1 x reset button
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This usart is used for console output on stm32h743i-disco board
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Add usart2 pins definition in order to add usart2 support
dedicated for console output on stm32h743i-disco board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
The A83T has 1 pingroup with 13 pins belonging to the R_PIO
or special pin controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The dev_attrs field has long been "depreciated" and is finally being
removed, so move the driver to use the "correct" dev_groups field
instead for struct bus_type.
Cc: Russell King <linux@armlinux.org.uk>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The improved type-checking version of container_of() triggers a warning for
xchg_xen_ulong, pointing out that 'xen_ulong_t' is unsigned, but atomic64_t
contains a signed value:
drivers/xen/events/events_2l.c: In function 'evtchn_2l_handle_events':
drivers/xen/events/events_2l.c:187:1020: error: call to '__compiletime_assert_187' declared with attribute error: pointer type mismatch in container_of()
This adds a cast to work around the warning.
Cc: Ian Abbott <abbotti@mev.co.uk>
Fixes: 85323a991d ("xen: arm: mandate EABI and use generic atomic operations.")
Fixes: daa2ac80834d ("kernel.h: handle pointers to arrays better in container_of()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Acked-by: Ian Abbott <abbotti@mev.co.uk>
The size field of the memory node is wrong. Rely on the default value in
sama5d2.dtsi that happens to be correct for the SAMA5D2 Xplained board.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
First we define an ABI using the vcpu devices that lets userspace set
the interrupt numbers for the various timers on both the 32-bit and
64-bit KVM/ARM implementations.
Second, we add the definitions for the groups and attributes introduced
by the above ABI. (We add the PMU define on the 32-bit side as well for
symmetry and it may get used some day.)
Third, we set up the arch-specific vcpu device operation handlers to
call into the timer code for anything related to the
KVM_ARM_VCPU_TIMER_CTRL group.
Fourth, we implement support for getting and setting the timer interrupt
numbers using the above defined ABI in the arch timer code.
Fifth, we introduce error checking upon enabling the arch timer (which
is called when first running a VCPU) to check that all VCPUs are
configured to use the same PPI for the timer (as mandated by the
architecture) and that the virtual and physical timers are not
configured to use the same IRQ number.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
We currently initialize the arch timer IRQ numbers from the reset code,
presumably because we once intended to model multiple CPU or SoC types
from within the kernel and have hard-coded reset values in the reset
code.
As we are moving towards userspace being in charge of more fine-grained
CPU emulation and stitching together the pieces needed to emulate a
particular type of CPU, we should no longer have a tight coupling
between resetting a VCPU and setting IRQ numbers.
Therefore, move the logic to define and use the default IRQ numbers to
the timer code and set the IRQ number immediately when creating the
VCPU.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
As we are about to support VCPU attributes to set the timer IRQ numbers
in guest.c, move the static inlines for the VCPU attributes handlers
from the header file to guest.c.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Configuration of the lcd0 pinmux group and GPIO hog for the external
GPIO mux are done using a single device node, causing the "output-high"
property to be applied to both. This will fail for the pinmux group,
but doesn't cause any harm, as the failure is ignored silently.
However, after "pinctrl: sh-pfc: propagate errors on group config", the
failure will become fatal, leading to a broken display:
sh-pfc e6050000.pin-controller: pin_config_group_set op failed for group 102
sh-pfc e6050000.pin-controller: Error applying setting, reverse things back
sh-pfc e6050000.pin-controller: failed to select default state
Move the GPIO hog to its own node to fix this.
Fixes: ffd2f9a5af ("ARM: shmobile: armadillo800eva dts: Add pinctrl and gpio-hog for lcdc0")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Changes include:
- Fix an issue with migrating GICv2 VMs on GICv3 systems.
- Squashed a bug for gicv3 when figuring out preemption levels.
- Fix a potential null pointer derefence in KVM happening under memory
pressure.
- Maintain RES1 bits in the SCTLR_EL2 to make sure KVM works on new
architecture revisions.
- Allow unaligned accesses at EL2/HYP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZODC6AAoJEEtpOizt6ddy7qsH/RakZzHHlPcIFk+VPhK4AvIV
ke6y1IznIVVv024geILb2NyF2pZoSUROxk1NF0wBIWM4ryjPm7oYgK7TTLyxkiX0
00gNxWpRRerCSxfh11a28tQywc7ATlw0yFpogGvbbHG9qEMX1NaGP/CNFK5us0LT
dw3y7jIZounlHlHu0W85AE27Osn5anFPHQnEtvJlUsM7WkIQf765EIfttXGUKRDZ
szmwuFAhdsSeIfo23LNXj87WAn6uP/37qRUmNXnxSya4u5urXa4qlOM5Hvg6agw2
K6LdpDXF/FnHhiT+b/xMTRPPivy4rXJZTpP51shl5GqKE2gI0tbhsHwJJ5Di/Aw=
=3xSf
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.12-rc5-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Fixes for v4.12-rc5 - Take 2
Changes include:
- Fix an issue with migrating GICv2 VMs on GICv3 systems.
- Squashed a bug for gicv3 when figuring out preemption levels.
- Fix a potential null pointer derefence in KVM happening under memory
pressure.
- Maintain RES1 bits in the SCTLR_EL2 to make sure KVM works on new
architecture revisions.
- Allow unaligned accesses at EL2/HYP
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
[tony@atomide.com: left out probe changes to avoid merge conflict]
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kcalloc".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data structure by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Note that omap_init_sti() won't do anything so we can
remove omap2_init_devices() as pointed out by Sebastian
Reichel <sebastian.reichel@collabora.co.uk>.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Note that the volt_data is still being used.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace hard-coded values of interrupt flags with respective macros from
header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable OV2640 camera support of STM32F429-EVAL board.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch set each gpio controller as a interrupt controller. User who
wants to use gpio as interrupt will have choice to use either "gpiolib"
interface or "common" interrupt interface.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Allwinner V3s SoC features a "Display Engine 2.0" with only one mixer
and only one TCON connected to this mixer, which have RGB LCD output.
Add device nodes for this display pipeline.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add SoC specific compatibles for all sunXi crypto nodes, in addition to
the one already used (allwinner,sun4i-a10-crypto).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node for the cryptographic engine that can be found on sun5i SoCs.
This cryptographic engine is compatible with the Allwinner cryptographic
accelerator driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Adjust a line in this description for the software module.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The script "checkpatch.pl" pointed information out like the following.
WARNING: void function return statements are not generally useful
Thus remove such a statement in the affected function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suspend and resume on imx6ull is currenty not working because of some
missed checks where behavior should match imx6ul.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Support for imx6ull is already present but it's based on
of_machine_is_compatible("fsl,imx6ull") checks. Add it to the MXC_CPU_*
enumeration as well.
This also fixes /sys/devices/soc0/soc_id reading "Unknown".
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6 PCI driver ignores the GPIO polarity from 'reset-gpio' and
considers that the PCI reset is active low, unless the
property 'reset-gpio-active-high' is present.
Fix the device tree description by explicitly passing the
'GPIO_ACTIVE_LOW' flag to the 'reset-gpio' property.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull networking fixes from David Miller:
1) Made TCP congestion control documentation match current reality,
from Anmol Sarma.
2) Various build warning and failure fixes from Arnd Bergmann.
3) Fix SKB list leak in ipv6_gso_segment().
4) Use after free in ravb driver, from Eugeniu Rosca.
5) Don't use udp_poll() in ping protocol driver, from Eric Dumazet.
6) Don't crash in PCI error recovery of cxgb4 driver, from Guilherme
Piccoli.
7) _SRC_NAT_DONE_BIT needs to be cleared using atomics, from Liping
Zhang.
8) Use after free in vxlan deletion, from Mark Bloch.
9) Fix ordering of NAPI poll enabled in ethoc driver, from Max
Filippov.
10) Fix stmmac hangs with TSO, from Niklas Cassel.
11) Fix crash in CALIPSO ipv6, from Richard Haines.
12) Clear nh_flags properly on mpls link up. From Roopa Prabhu.
13) Fix regression in sk_err socket error queue handling, noticed by
ping applications. From Soheil Hassas Yeganeh.
14) Update mlx4/mlx5 MAINTAINERS information.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (78 commits)
net: stmmac: fix a broken u32 less than zero check
net: stmmac: fix completely hung TX when using TSO
net: ethoc: enable NAPI before poll may be scheduled
net: bridge: fix a null pointer dereference in br_afspec
ravb: Fix use-after-free on `ifconfig eth0 down`
net/ipv6: Fix CALIPSO causing GPF with datagram support
net: stmmac: ensure jumbo_frm error return is correctly checked for -ve value
Revert "sit: reload iphdr in ipip6_rcv"
i40e/i40evf: proper update of the page_offset field
i40e: Fix state flags for bit set and clean operations of PF
iwlwifi: fix host command memory leaks
iwlwifi: fix min API version for 7265D, 3168, 8000 and 8265
iwlwifi: mvm: clear new beacon command template struct
iwlwifi: mvm: don't fail when removing a key from an inexisting sta
iwlwifi: pcie: only use d0i3 in suspend/resume if system_pm is set to d0i3
iwlwifi: mvm: fix firmware debug restart recording
iwlwifi: tt: move ucode_loaded check under mutex
iwlwifi: mvm: support ibss in dqa mode
iwlwifi: mvm: Fix command queue number on d0i3 flow
iwlwifi: mvm: rs: start using LQ command color
...
We currently have the HSCTLR.A bit set, trapping unaligned accesses
at HYP, but we're not really prepared to deal with it.
Since the rest of the kernel is pretty happy about that, let's follow
its example and set HSCTLR.A to zero. Modern CPUs don't really care.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
The dwmac-sun8i hardware is present on the Orange PI Zero.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the Banana Pi M2+
It uses an external PHY rtl8211e via RGMII.
This patch create the needed regulator, emac and phy nodes.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the Orange PI plus.
It uses an external PHY rtl8211e via RGMII.
This patch create the needed regulator, emac and phy nodes.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the NanoPi Neo.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Orange Pi PC Plus, the polarity of the LEDs on the RJ45 Ethernet
port were changed from active low to active high.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the Orange PI 2.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the Orange PI One.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the Orange PI PC.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i is an ethernet MAC hardware that support 10/100/1000
speed.
This patch enable the dwmac-sun8i on Allwinner H3/H5 SoC Device-tree.
SoC H3/H5 have an internal PHY, so optionals syscon and ephy are set.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch add the dt node for the syscon register present on the
Allwinner H3/H5
Only two register are present in this syscon and the only one useful is
the one dedicated to EMAC clock..
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that the R_CCU device tree binding headers have been merged, we
can convert the raw number references in the device trees to use the
defined macros.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order GPIOS from this controller to be used with the "gpio-hogs"
property, the tca6416 node has to properly labeled as a gpio-controller,
and use #gpio-cells.
With that, the SEL_A, SEL_B, SEL_C lines that are used to select VPIF
input can be configured using GPIO hogs.
As an example, example, the configuration below selects the analog video
input on the da850-evm UI board:
&tca6416 {
status = "okay";
sel_a {
gpio-hog;
gpios = <7 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "ADC_ENn";
};
sel_b {
gpio-hog;
gpios = <6 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "CAMERA_ENn";
};
sel_c {
gpio-hog;
gpios = <5 GPIO_ACTIVE_HIGH>;
output-low;
line-name = "VIDEO_IN_ENn";
};
};
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Interrupt-parent property is defined in the root node as
"interrupt-parent = <&intc>". This interrupt-parent value becomes
the default for the system, so removed redundant "interrupt-parent"
property from mmc, mac, lcdc and tscadc nodes.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the serial slave device for the WL1835 Bluetooth interface.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Ricardo Salveti <ricardo.salveti@linaro.org>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dcdc3 supplies to DDR on AM43x series. When we set both
min and max values to the same value. The regulator framework
sets that particular voltage. This is bad as we are changing
the ddr voltage when executing from ddr. Hence remove the min and
max values. The ddr supply voltage shall be set from bootloader
when not executing from ddr and not while executing from kernel.
The previous discussion can be found here:
http://www.spinics.net/lists/devicetree/msg56399.html
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBone Blue is robotics-oriented version of the BeagleBone Black (BBB).
This board can be indentified by the BLAx value after A335BNLT (BBB)
in the at24 eeprom:
BLAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 4c 41 30 |.U3.A335BNLTBLA2|]
http://beagleboard.org/bluehttps://github.com/beagleboard/beaglebone-blue
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
Acked-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The twl4030_charger driver expects an iio channel to detect the
presence of an AC charger by looking at VAC (madc channel 11).
This definition is missing in the device tree.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If clkctrl clocks are available on a device, populate these automatically
to replace hwmod main_clk info. First, the patch parses all "ti,clkctrl"
compatible nodes and maps these against existing clockdomain data. Once
done, individual hwmod init routines can search for a clkctrl clock
handle based on the clockdomain info and the created mapping.
This patch also drops the obsolete "_mod_ck" search as the implementation
required for this was not accepted usptream.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This function gets the physical base address of a clockdomain.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This new function can be used to get the physical address of a
clockdomain. Required for mapping the clkctrl clocks under hwmod
without modification to DT data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In some cases the physical address info is needed, so store this
under the existing cm*_base, prm_base and prcm_mpu_base variables.
These are converted now to structs that contain both virtual and
physical address base for the instance.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These extra optional clocks are required as main clock for these modules
are going to be routed to the main module clock. Otherwise, the hdmi / tv
clocks are not going to be enabled during usage, leading to failure.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The mux clock handle shall be provided via "fck" DT handle. This avoids
the need to lookup the main clock via hwmod core, which will not work
with the clkctrl clock support anymore; the main clock is not going to
be a mux.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add information about the IPQ4019 debug UART physical and virtual
addresses in the DEBUG_QCOM_UARTDM Kconfig help section.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
These configs are required for booting kernel in QCOM IPQ4019 boards.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This defines the memory location and interrupt used by the GSBI8
I2C adapter on the MSM8660 SoCs. We add it as "disabled" by
default so that boards using this I2C can enable it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the Capella CM3605 ambient light and proximity sensor
to the APQ8060 DragonBoard device tree. Notice that we also set
up pin config for the AOUT line and GPIO lines, and that we set
the default trigger on the infrared LED to associate with the
"cm3605" trigger so the IR LED is controlled by this the CM3605
driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the PM8058 XOADC node to the PM8058 PMIC node,
defines the 16 channels and further also define an IIO HWMON
node for the channels that are used for housekeeping of
voltages and die temperature for the PMIC chip die.
Tested on the APQ8060 DragonBoard:
cd /sys/class/hwmon/hwmon0
cat in2_input
4773 (DC mains ~5V)
cat in4_input
625 (0.625V reference voltage)
cat in5_input
1250 (1.25V reference voltage)
cat temp1_input
35852 (die temperature)
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch fixes two typos in the i2c_0 node for the ipq4019.
The reg property length is just 0x600. The core clock is
GCC_BLSP1_QUP1_I2C_APPS_CLK. GCC_BLSP1_QUP2_I2C_APPS_CLK is
used by the second i2c.
Fixes: e76b4284b5 ("qcom: ipq4019: add i2c node to ipq4019 SoC and DK01 device tree")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The gsbi_serial7 under gsbi7 is used by the IPQ8068 based board EWS870AP as
main serial console.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Follow the recent trend for the license description, and fix the wrongly
stated X11 to MIT.
The X11 license text [1] is explicitly for the X Consortium and has a
couple of extra clauses. The MIT license text [2] is actually what the
current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Pull ARM fixes from Russell King:
"Three fixes this time around:
- Two fixes for noMMU, fixing the decompressor header layout, and
preventing a build error with some configurations.
- Fixing the hyp-stub updates that went in during the merge window
for platforms that use MCPM"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8677/1: boot/compressed: fix decompressor header layout for v7-M
ARM: 8676/1: NOMMU: provide pgprot_device() macro
ARM: 8675/1: MCPM: ensure not to enter __hyp_soft_restart from loopback and cpu_power_down
The script "checkpatch.pl" pointed information out like the following.
ERROR: do not use assignment in if condition
Thus fix the affected source code place.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Wire up the existing arm64 support for SMBIOS tables (aka DMI) for ARM as
well, by moving the arm64 init code to drivers/firmware/efi/arm-runtime.c
(which is shared between ARM and arm64), and adding a asm/dmi.h header to
ARM that defines the mapping routines for the firmware tables.
This allows userspace to access these tables to discover system information
exposed by the firmware. It also sets the hardware name used in crash
dumps, e.g.:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = ed3c0000
[00000000] *pgd=bf1f3835
Internal error: Oops: 817 [#1] SMP THUMB2
Modules linked in:
CPU: 0 PID: 759 Comm: bash Not tainted 4.10.0-09601-g0e8f38792120-dirty #112
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
^^^
NOTE: This does *NOT* enable or encourage the use of DMI quirks, i.e., the
the practice of identifying the platform via DMI to decide whether
certain workarounds for buggy hardware and/or firmware need to be
enabled. This would require the DMI subsystem to be enabled much
earlier than we do on ARM, which is non-trivial.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170602135207.21708-14-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
imx7d-sdb has a BCM4339 BT chip connected to UART6.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d-sdb has a BCM4339 Wifi chip connected to USDHC2.
Add support for it.
While at it, move the WL_REG_ON pin to the correct pinctrl node.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not recommended to place the regulator nodes inside 'simple-bus',
so adjust them accordingly.
The motivation for rearranging this is to make it easier to add new
regulator nodes in the future.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The FEC driver ignores the GPIO polarity from 'phy-reset-gpios' and
considers that the Ethernet PHY is active low, unless the
property 'phy-reset-active-high' is present.
Fix the device tree description by explicitly passing the
'GPIO_ACTIVE_LOW' flag to the 'phy-reset-gpios' property.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As reported by Patrice, the header layout of the decompressor is
incorrect when building for v7-M. In this case, the __nop macro
resolves to 'mov r0, r0', which is emitted as a narrow encoding,
resulting in the header data fields to end up at lower offsets than
required.
Given the variety of targets we need to support with the same code,
the startup sequence is a bit of a jumble, and uses instructions
and macros whose encoding widths cannot be specified (badr), or only
exist in a narrow encoding (bx)
So force the use of a wide encoding in __nop, and replace the start
sequence with a simple jump to the label marking the start of code,
preceded by a Thumb2 mode switch if required (using explicit wide
encodings where appropriate). The label itself can be moved to the
start of code [where it belongs] due to the larger range of branch
instructions as compared to adr instructions.
Reported-by: Patrice CHOTARD <patrice.chotard@st.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
NOMMU build leads to the following error:
CC drivers/pci/mmap.o
drivers/pci/mmap.c: In function 'pci_mmap_resource_range':
drivers/pci/mmap.c:60:3: error: implicit declaration of function 'pgprot_device' [-Werror=implicit-function-declaration]
vma->vm_page_prot = pgprot_device(vma->vm_page_prot);
^
cc1: some warnings being treated as errors
scripts/Makefile.build:302: recipe for target 'drivers/pci/mmap.o' failed
make[2]: *** [drivers/pci/mmap.o] Error 1
scripts/Makefile.build:561: recipe for target 'drivers/pci' failed
make[1]: *** [drivers/pci] Error 2
Makefile:1016: recipe for target 'drivers' failed
make: *** [drivers] Error 2
Fix it with support of pgprot_device() macro for NOMMU.
Fixes: 00d2904ffe ("ARM/PCI: Use generic pci_mmap_resource_range()")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Don't use request-less VCPU kicks when injecting IRQs, as a VCPU
kick meant to trigger the interrupt injection could be sent while
the VCPU is outside guest mode, which means no IPI is sent, and
after it has called kvm_vgic_flush_hwstate(), meaning it won't see
the updated GIC state until its next exit some time later for some
other reason. The receiving VCPU only needs to check this request
in VCPU RUN to handle it. By checking it, if it's pending, a
memory barrier will be issued that ensures all state is visible.
See "Ensuring Requests Are Seen" of
Documentation/virtual/kvm/vcpu-requests.rst
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
A request called EXIT is too generic. All requests are meant to cause
exits, but different requests have different flags. Let's not make
it difficult to decide if the EXIT request is correct for some case
by just always providing unique requests for each case. This patch
changes EXIT to SLEEP, because that's what the request is asking the
VCPU to do.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
arm/arm64 already has one VCPU request used when setting pause,
but it doesn't properly check requests in VCPU RUN. Check it
and also make sure we set vcpu->mode at the appropriate time
(before the check) and with the appropriate barriers. See
Documentation/virtual/kvm/vcpu-requests.rst. Also make sure we
don't leave any vcpu requests we don't intend to handle later
set in the request bitmap. If we don't clear them, then
kvm_request_pending() may return true when it shouldn't.
Using VCPU requests properly fixes a small race where pause
could get set just as a VCPU was entering guest mode.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Marc Zyngier suggested that we define the arch specific VCPU request
base, rather than requiring each arch to remember to start from 8.
That suggestion, along with Radim Krcmar's recent VCPU request flag
addition, snowballed into defining something of an arch VCPU request
defining API.
No functional change.
(Looks like x86 is running out of arch VCPU request bits. Maybe
someday we'll need to extend to 64.)
Signed-off-by: Andrew Jones <drjones@redhat.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
By moving the kernel side __SI_* defintions right next to the userspace
ones we can kill the non-uapi versions of <asm/siginfo.h> include
include/asm-generic/siginfo.h and untangle the unholy mess of includes.
[ tglx: Removed uapi/asm/siginfo.h from m32r, microblaze, mn10300 and score ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-ia64@vger.kernel.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: sparclinux@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Link: http://lkml.kernel.org/r/20170603190102.28866-6-hch@lst.de
This option was removed by "make savedefconfig" in
commit c5054a98bc ("ARM: imx_v6_v7_defconfig: Select SMSC_PHY")
This happened because CONFIG_DEBUG_FS was implicitly selected by
CONFIG_TREE_RCU_TRACE which defaulted to true because CONFIG_RCU_TRACE
was enabled by default by commit 961518259b ("rcu: Enable RCU
tracepoints by default to aid in debugging")
Recently however CONFIG_RCU_TRACE was completely removed by
commit 6e74c237c410 ("rcu: Remove debugfs tracing")
The result is that imx_v6_v7_defconfig no longer includes DEBUG_FS on
linux-next since next-20170517. This is bad, DEBUG_FS is extremely
useful for kernel introspection and testing.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that some functions that deal with arch topology information live
under drivers, there is a clash of naming that might create confusion.
Tidy things up by creating a topology namespace for interfaces used by
arch code; achieve this by prepending a 'topology_' prefix to driver
interfaces.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create a new header file (include/linux/arch_topology.h) and put there
declarations of interfaces used by arm, arm64 and drivers code.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce the scope of cap_parsing_failed (making it static in
drivers/base/arch_topology.c) by slightly changing {arm,arm64} DT
parsing code.
For arm checking for !cap_parsing_failed before calling normalize_
cpu_capacity() is superfluous, as returning an error from parse_
cpu_capacity() (above) means cap_from _dt is set to false.
For arm64 we can simply check if raw_capacity points to something,
which is not if capacity parsing has failed.
Suggested-by: Morten Rasmussen <morten.rasmussen@arm.com>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arm and arm64 share lot of code relative to parsing CPU capacity
information from DT, using that information for appropriate scaling and
exposing a sysfs interface for chaging such values at runtime.
Factorize such code in a common place (driver/base/arch_topology.c) in
preparation for further additions.
Suggested-by: Will Deacon <will.deacon@arm.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs cpu_capacity entry for each CPU has nothing to do with
PROC_FS, nor it's in /proc/sys path.
Remove such ifdef.
Cc: Russell King <linux@arm.linux.org.uk>
Reported-and-suggested-by: Sudeep Holla <sudeep.holla@arm.com>
Fixes: 7e5930aaef ('ARM: 8622/3: add sysfs cpu_capacity attribute')
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parse_cpu_capacity() has to return 0 on failure, but it currently returns
1 instead if raw_capacity kcalloc failed.
Fix it (by directly returning 0).
Reported-by: Morten Rasmussen <morten.rasmussen@arm.com>
Fixes: 06073ee267 ('ARM: 8621/3: parse cpu capacity-dmips-mhz from DT')
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Vincent Guittot <vincent.guittot@linaor.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AR100 clock within the R_CCU (PRCM) has the PLL_PERIPH0 as one of
its parents.
This adds the reference in the device tree describing this relationship.
This patch uses a raw number for the clock index to ease merging by
avoiding cross tree dependencies.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T's PRCM has the same set of clocks and resets as the A64.
However, a few dividers are different. And due to the lack of a low
speed 32.768 kHz oscillator, a few of the clock parents are different.
The PRCM also has controls for various power domains. These are not
supported yet, neither in software nor in the device tree binding.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Exynos5250 and Exynos542x SoCs have the same CEC hardware module as
Exynos4 SoC series, so enable support for it using the same compatible
string.
Tested on Odroid XU3 (Exynos5422) and Google Snow (Exynos5250) boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Rockchip's rk3229 evaluation board has one usb otg controller
and three usb host controllers. Each usb controller connect
with one usb2 phy port through UTMI+ interface. And the three
usb host interfaces use the same GPIO VBUS drive. Let's enable
them to support usb on rk3229 evb board.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds usb otg/host controllers and phys nodes on rk322x.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for low level debugging on Atmel samv7x.
Signed-off-by: Szemző András <sza@esh.hu>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There is currently no PM support for samx7 but the symbol can still be
selected. This avoids compilation issues.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This augments the Moxa Art and Aspeed device trees to:
- Explicitly name the clock "PCLK" as the Faraday FTTMR010
names it.
- List the Moxa timer as compatible with the Faradat FTTMR010
vanilla version.
- Add a comment that the Aspeed driver is a Faraday
FTTMR010 derivative.
- Pass all IRQs to the timer from Aspeed: they are all there
so they should be in the device tree, we only use the
first one anyways.
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the reset and clock lines to the Gemini core DTS SoC.
These bindings have been ACKed by the DT maintainer Rob.
The reset driver is going to be merged by the reset maintainer.
The clock driver is going to be merged by the clock maintainers.
Each of these have their macro defines coming with them, split
off as separate patches.
A post-rc1 patch will be sumbitted for switching the numerical
values to the defined macros in line with the ARM SoC DT header
merge strategy.
-----BEGIN PGP SIGNATURE-----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=SNKP
-----END PGP SIGNATURE-----
Merge tag 'gemini-v4.13-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
This is a first set of Gemini DTS patches for the v4.13 cycle.
This adds the reset and clock lines to the Gemini core DTS SoC.
These bindings have been ACKed by the DT maintainer Rob.
The reset driver is going to be merged by the reset maintainer.
The clock driver is going to be merged by the clock maintainers.
Each of these have their macro defines coming with them, split
off as separate patches.
A post-rc1 patch will be sumbitted for switching the numerical
values to the defined macros in line with the ARM SoC DT header
merge strategy.
* tag 'gemini-v4.13-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Add clocks to the Gemini SoC
ARM: dts: Add the Gemini reset controller
dt-bindings: Augment Gemini for clocks, resets
Signed-off-by: Olof Johansson <olof@lixom.net>
* Switch to panel-lvds bindings for Mitsubishi panels
* Clean up PFC node names
* Enable UHS-I SDR-50 and SDR-104 on r8a7793/Gose
* Add GyroADC clock and device for r8a7791 SoC
* Add USB clocks to device tree for r7s72100 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3Bjz
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.13
* Switch to panel-lvds bindings for Mitsubishi panels
* Clean up PFC node names
* Enable UHS-I SDR-50 and SDR-104 on r8a7793/Gose
* Add GyroADC clock and device for r8a7791 SoC
* Add USB clocks to device tree for r7s72100 SoC
* tag 'renesas-dt-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: renesas: Switch to panel-lvds bindings for Mitsubishi panels
ARM: dts: gose: Enable UHS-I SDR-50 and SDR-104
ARM: dts: r8a7793: set maximum frequency for SDHI clocks
ARM: dts: r8a7791: Add GyroADC clock and device node
ARM: dts: r7s72100: add usb clocks to device tree
ARM: dts: sh73a0: update PFC node name to pin-controller
ARM: dts: r8a7793: update PFC node name to pin-controller
ARM: dts: r8a7791: update PFC node name to pin-controller
ARM: dts: r8a7790: update PFC node name to pin-controller
ARM: dts: r8a7779: update PFC node name to pin-controller
ARM: dts: r8a7778: update PFC node name to pin-controller
ARM: dts: r8a7740: update PFC node name to pin-controller
ARM: dts: r8a73a4: update PFC node name to pin-controller
ARM: dts: emev2: update PFC node name to pin-controller
ARM: dts: r7s72100: add USB bit definitions
ARM: dts: r7s72100: add Renesas RZ/A1 pinctrl header
ARM: dts: r8a7791: add GyroADC clock
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu fixes for 4.12
Fix the interrupt description of the crypto node for device tree of
the Armada 7K/8K SoCs
* tag 'mvebu-fixes-4.12-1' of git://git.infradead.org/linux-mvebu: (316 commits)
arm64: marvell: dts: fix interrupts in 7k/8k crypto nodes
+ Linux 4.12-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>
Fixes for 4.12:
Fix two compilation issues
* tag 'at91-4.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: select CONFIG_ARM_CPU_SUSPEND
memory: atmel-ebi: mark PM ops as __maybe_unused
Signed-off-by: Olof Johansson <olof@lixom.net>
Most of DT files in ARM use #include "..." to make pre-processor
include DT in the same directory, but this is one of the exceptional
files that use #include <...> for that.
Fix it to remove -I$(srctree)/arch/$(SRCARCH)/boot/dts path from
dtc_cpp_flags.
ARM: dts: versatile: use #include "..." to include DT in the same directory
Most of DT files in ARM use #include "..." to make pre-processor
include DT in the same directory, but we have 3 exceptional files
that use #include <...> for that.
They must be fixed to remove -I$(srctree)/arch/$(SRCARCH)/boot/dts
path from dtc_cpp_flags.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The only adc button connected to adc input is recovery button.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Right now mach-imx6ul registers a fixup for the ksz8081 phy. The same
register values can be set through the micrel phy driver by using dts
properties.
This seems preferable and allows cleanly fixing suspend/resume.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the module autoloadable by tying it to the CPU feature bits that
describe whether the optional instructions it relies on are implemented
by the current CPU.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Make the module autoloadable by tying it to the CPU feature bit that
describes whether the optional instructions it relies on are implemented
by the current CPU.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Make the module autoloadable by tying it to the CPU feature bit that
describes whether the optional instructions it relies on are implemented
by the current CPU.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Make the module autoloadable by tying it to the CPU feature bit that
describes whether the optional instructions it relies on are implemented
by the current CPU.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Make the module autoloadable by tying it to the CPU feature bit that
describes whether the optional instructions it relies on are implemented
by the current CPU.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
NanoPi M1 Plus is designed and developed by FriendlyElec
for professionals, enterprise users, makers and hobbyists
using the Allwinner H3 SOC.
NanoPi M1 Plus key features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 1GB DDR3 RAM
- 8GB eMMC
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
While trying a fix a build warning unrelated to s3c64xx, I ran into
a circular dependency:
drivers/i2c/Kconfig:7: symbol I2C is selected by FB_DDC
drivers/video/fbdev/Kconfig:63: symbol FB_DDC is selected by FB_CYBER2000_DDC
drivers/video/fbdev/Kconfig:381: symbol FB_CYBER2000_DDC depends on FB_CYBER2000
drivers/video/fbdev/Kconfig:369: symbol FB_CYBER2000 depends on FB
drivers/video/fbdev/Kconfig:5: symbol FB is selected by DRM_KMS_FB_HELPER
drivers/gpu/drm/Kconfig:72: symbol DRM_KMS_FB_HELPER is selected by DRM_KMS_CMA_HELPER
drivers/gpu/drm/Kconfig:137: symbol DRM_KMS_CMA_HELPER is selected by DRM_PL111
drivers/gpu/drm/pl111/Kconfig:1: symbol DRM_PL111 depends on ARM_AMBA
drivers/amba/Kconfig:1: symbol ARM_AMBA is selected by S3C64XX_PL080
arch/arm/mach-s3c64xx/Kconfig:42: symbol S3C64XX_PL080 default value contains DMADEVICES
drivers/dma/Kconfig:5: symbol DMADEVICES is selected by SND_SOC_SH4_SIU
sound/soc/sh/Kconfig:29: symbol SND_SOC_SH4_SIU is selected by SND_SIU_MIGOR
sound/soc/sh/Kconfig:59: symbol SND_SIU_MIGOR depends on I2C
The I2C and FB dependencies are hard to untangle, but I notice that
S3C64XX_PL080 selecting ARM_AMBA is one piece of the puzzle that
can easily be avoided, as ARCH_S3C64XX already select ARM_AMBA.
Removing the redundant 'select' now can help us in the future if we
run into a variation of the same dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add the needed clock nodes for the CLKOUT2 to be usable by boards.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
sama5d3 CPU modules embed a parallel NOR flash connected to the EBI bus.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use the new EBI/NAND bindings to declare NAND chips and remove old NAND
nodes along the way.
Note that we keep using old bindings in at91rm9200.dtsi because this
SoC is not supported by the EBI driver.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Declare new nodes for the EBI and NAND controllers embedded in various
at91/sama5 SoCs.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to the binding documentation and the source code the atmel-gpio
controller takes IRQ_TYPE_* as its flags values, not GPIO_ACTIVE_*.
This patch uses the right variable type which yields the same result
when compiled. Note that this might be wrong and actually
IRQ_TYPE_LEVEL_LOW is intended by the dt author.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
David Mosberger reports random segfaults and other problems when running
his buildroot userspace. It turns out that his kernel did not have
support for Thumb userspace, nor did his application, but glibc made use
of Thumb instructions in glibc.
The kernel Thumb support option already recommends being enabled, and
is also so biased, but clearly this is not enough of a recommendation.
So, hide this behind CONFIG_EXPERT as well, and include a note to
indicate the potential issues if it's turned off and userspace Thumb
mode is made use of.
Reported-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The gpio node has 144 gpios. Each gpio is capable of generating
an interrupt. Hence add interrupt-controller property to the gpio
node. With this in place one can use interrupts property in device
tree to request for the gpio interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CPPI 4.1 DMA is now supported on AM18xx.
Update the config to use it instead of PIO mode.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds CPPI 4.1 DMA controller to USB OTG controller.
Changes since v2:
- Fixed the the property reg-names (had glue register defined)
- Removed few useless property
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
arch_teardown_dma_ops() being the inverse of arch_setup_dma_ops()
,dma_ops should be cleared in the teardown path. Currently, only the
device's iommu mapping structures are cleared in arch_teardown_dma_ops,
but not the dma_ops. So on the next reprobe, dma_ops left in place is
stale from the first IOMMU setup, but iommu mappings has been disposed
of. This is a problem when the probe of the device is deferred and
recalled with the IOMMU probe deferral.
So for fixing this, slightly refactor by moving the code from
__arm_iommu_detach_device to arm_iommu_detach_device and cleanup
the former. This takes care of resetting the dma_ops in the teardown
path.
Fixes: 09515ef5dd ("of/acpi: Configure dma operations at probe time for platform/amba/pci bus devices")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
arch_setup_dma_ops() is used in device probe code paths to create an
IOMMU mapping and attach it to the device. The function assumes that the
device is attached to a device-specific IOMMU instance (or at least a
device-specific TLB in a shared IOMMU instance) and thus creates a
separate mapping for every device.
On several systems (Renesas R-Car Gen2 being one of them), that
assumption is not true, and IOMMU mappings must be shared between
multiple devices. In those cases the IOMMU driver knows better than the
generic ARM dma-mapping layer and attaches mapping to devices manually
with arm_iommu_attach_device(), which sets the DMA ops for the device.
The arch_setup_dma_ops() function takes this into account and bails out
immediately if the device already has DMA ops assigned. However, the
corresponding arch_teardown_dma_ops() function, called from driver
unbind code paths (including probe deferral), will tear the mapping down
regardless of who created it. When the device is reprobed
arch_setup_dma_ops() will be called again but won't perform any
operation as the DMA ops will still be set.
We need to reset the DMA ops in arch_teardown_dma_ops() to fix this.
However, we can't do so unconditionally, as then a new mapping would be
created by arch_setup_dma_ops() when the device is reprobed, regardless
of whether the device needs to share a mapping or not. We must thus keep
track of whether arch_setup_dma_ops() created the mapping, and only in
that case tear it down in arch_teardown_dma_ops().
Keep track of that information in the dev_archdata structure. As the
structure is embedded in all instances of struct device let's not grow
it, but turn the existing dma_coherent bool field into a bitfield that
can be used for other purposes.
Fixes: 09515ef5dd ("of/acpi: Configure dma operations at probe time for platform/amba/pci bus devices")
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The reference to cpu_resume requires the corresponding
generic code to be enabled when CONFIG_PM is set:
arch/arm/mach-at91/pm.o: In function `sama5d2_pm_init':
pm.c:(.init.text+0x5e8): undefined reference to `cpu_resume'
Fixes: 24a0f5c539 ("ARM: at91: pm: Add sama5d2 backup mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add node for SPI NOR flash on orange-pi-zero board. Disable this node
by default and leave it to users to enable it if their board has
SPI NOR flash chip populated.
SPI NOR flash was optional in the first production batch in Dec 2016.
In later batches flash chip was pre-populated. However there should
be quite a few boards around which do not have flash chip.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The USB PHY can use either a GPIO pin or the PMIC's USB power supply
to sense VBUS. Since both options are available on the Cubietruck,
add the missing property for the USB power supply to the USB PHY node.
The device tree provides all usable options. Ultimately, which method
is used is up to the driver implementation.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ACIN pins of the AXP221 PMIC on the A31 Hummingbird are tied to the
DC jack on the board through a 12V to 5V buck converter.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ACIN pins of the AXP209 PMIC on the Cubieboard are tied to the
DC jack on the board.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ACIN pins of the AXP209 PMIC on the Bananapi M1 Plus are tied to the
"power input" micro USB connector next to the SATA connector on the board.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ACIN pins of the AXP209 PMIC on the Cubieboard 2 are tied to the
DC jack on the board.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We want to keep node references in alphabetical order, except for
instances where node must be #included first.
Move the usb_otg node reference so that all references to non-AXP209
device nodes are in alphabetical order.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Two of the Ethernet switches on this board have EEPROMs connected.
Add the eeprom-length property to the device tree, making it possible
to access the EEPROM using ethtool -e.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch extends the L2 cache controller node for the Amlogic Meson8
and Meson8b SoCs with some missing parameters. These are taken from the
Amlogic GPL kernel source.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
[apply the change to Meson8 and Meson8b and updated description]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Currently only meson6.dtsi and meson8.dtsi inherit the generic
meson.dtsi. However, since the Meson8b platform is basically a slightly
updated version of Meson8 we can safely inherit meson.dtsi. An indicator
for this are the nodes which are identical in meson.dtsi and
meson8b.dtsi (L2, gic, timer, uart_AO, uart_A, uart_B, uart_C).
Additionally this makes the following devices available on Meson8b which
were not avaialble before (however, since all affected drivers support
Meson6, Meson8 and the whole GX series there's no reason to assume that
they are not working):
- i2c_a and i2c_B
- the IR receiver
- SPFIC (SPI flash controller)
- the dwmac ethernet controller
Differences between Meson8 and Meson8b seem to be:
- ARM Cortex-A5 core instead of Cortex-A9 on Meson8
- dwmac on Meson8b supports RGMII
- small pinctrl updates
Inheriting meson.dtsi makes it easier to maintain by removing duplicate
definitions.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic Meson SoCs have most of the internal peripherals organized
in busses. Use them to make the dts easier to read and to avoid
duplicated register (bus) offset definitions.
The bus information is taken from the vendor kernel:
#define IO_CBUS_PHY_BASE 0xc1100000 ///2M
#define IO_AOBUS_PHY_BASE 0xc8100000 ///1M
There are more internal busses (such as the abp bus which seems to
contain audio, HDMI and Mali registers), but since we don't have
drivers for them yet these are not added (yet).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[khilman: minor whitespace fix]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Looks like nobody bothered to configure USB host for 37xx-evm
when we converted things to device tree, so let's add it. This
is similar to beagleboard configuration with few extra quirks
to configure the port. And as with beagleboard, OHCI won't work
because there is no USB LS/FS PHY. A HS USB hub is needed to use
devices like keyboard and mice.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As long as the kernel cmdline has "earlycon" in it, this allows
seeing debug messages earlier and does not require DEBUG_LL to
be enabled.
Acked-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As long as the kernel cmdline has "earlycon" in it, this allows
seeing debug messages earlier and does not require DEBUG_LL to
be enabled.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the serial slave device for the WL1835 Bluetooth interface.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the AM571x IDK board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, and DSP1 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the AM572x IDK board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, DSP1 and DSP2 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With two separate &gpmc nodes the second ranges property overwrites the
first. So put nand and ethernet in a single node and merge the ranges.
While at it also fix the ethernet suffix.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't need to bitbang these pins anymore, instead we muxed these
pins as SPI, after this change, done in commit 6c69f726, we introduced
the following error:
pinctrl-single 44e10800.pinmux: pin PIN85 already requested \
by 44e10800.pinmux; cannot claim for 48030000.spi
pinctrl-single 44e10800.pinmux: pin-85 (48030000.spi) status -22
Fixes: 6c69f726 ("ARM: dts: am335x-sl50: Enable SPI0 interface and Flash Memory")
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The second version of the hardware moved the card detect pin from gpio0_6
to gpio1_9, as we won't support the first hardware version fix the pinmux
configuration of this pin.
Fixes: 8584d4fc ("ARM: dts: am335x-sl50: Add Toby-Churchill SL50 board support.")
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ethernet networking on K2L has been broken since v4.11-rc1. This was
caused by commit 32a34441a9 ("ARM: keystone: dts: fix netcp clocks
and add names"). This commit inadvertently moves on-chip static RAM
clock to the end of list of clocks provided for netcp. Since keystone
PM domain support does not have a list of recognized con_ids, only the
first clock in the list comes under runtime PM management. This means
the OSR (On-chip Static RAM) clock remains disabled and that broke
networking on K2L.
The OSR is used by QMSS on K2L as an external linking RAM. However this
is a standalone RAM that can be used for non-QMSS usage (as well as from
DSP side). So add a SRAM device node for the same and add the OSR clock
to the node.
Remove the now redundant OSR clock node from netcp.
To manage all clocks defined for netCP's use by runtime PM needs keystone
generic power domain (genpd) driver support which is under works.
Meanwhile, this patch restores K2L networking and is correct irrespective
of any future genpd work since OSR is an independent module and not part
of NetCP anyway.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
[nsekhar@ti.com: commit message updates, port to latest mainline]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: stable@vger.kernel.org # for 4.11
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The text patching functions which are invoked from jump_label and kprobes
code are protected against cpu hotplug at the call sites.
Use stop_machine_cpuslocked() to avoid recursion on the cpu hotplug
rwsem. stop_machine_cpuslocked() contains a lockdep assertion to catch any
unprotected callers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20170524081549.275871311@linutronix.de
arch_hw_breakpoint_init() holds get_online_cpus() while registerring the
hotplug callbacks.
cpuhp_setup_state() invokes get_online_cpus() as well. This is correct, but
prevents the conversion of the hotplug locking to a percpu rwsem.
Use cpuhp_setup_state_cpuslocked() to avoid the nested call. Convert
*_online_cpus() to the new interfaces while at it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20170524081548.170940729@linutronix.de
Identical to the setup on Koelsch.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We currently have three device nodes for the same USB hardware
block, as evident by the reuse of the same reg address multiple
times. Now that the chipidea driver fully supports OTG with the
MSM wrapper we can collapse the three nodes into one USB device
node, reflecting the true nature of the hardware.
Since we're here, we also mark the irq trigger flags correctly,
as IRQ_TYPE_LEVEL_HIGH instead of IRQ_TYPE_NONE.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This USB controller has two phys, so add them both underneath the
ULPI bus, but only enable one of them based on the board
configuration. To get OTG to work, we need to add the id and vbus
detection info and also populate the regulators for the vbus
supply.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
These regulators are controlled by the SPMI regulator driver
instead of the RPM regulator driver in the downstream android
kernel sources. Let's remove them from the DTS here because
they'll never be used by the RPM regulator driver.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
please pull the following:
- Phil provides a fix for the BCM283x (Raspberry Pi) by flagging the first
4KiB of physical memory as a reserved region in order to let the secondary
cores successfully spin until they are brought online
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJZJ03UAAoJEIfQlpxEBwcEnOwP/02l54jeRuwFFqn8yM89S0rE
ZXgx+DuIlcWGtFbVjzKtqcpV+9Gjdh9eOQaS9SN7p9C/UFVM4m+UUpVojs+yq538
Z6p8soGTlMhQb6zAuajaiOMp7AlARH674kU3cnRi28Iwt81FiVLrAkMf9lRLkTCx
4iyha1vXVQOwY4BxSw91I3gK8vDlDBKLRBmpiPPQ9ZUFNWXsVzbFCrirxUwd5J/h
8TqsSsfsOexqQCHLgixdpu5s5jGWZVMoP+a3xbsF066vv9K0BHZeBrzuQfb5iRdl
O92JlsVzs8gW3C1/0saGRefLwc5kRytWSNpU0RZe/AjkNHL7IR6LgIU0UNaQhwug
N4IUryKLtbJMBuLHYpwliZKmHO9TlDmOC1wdkOnnjYoS9fDEOuMo+UH2aRmFAxcz
gJgrDFb6ajQchM7dPswGrAq+09mcqkkorIvqbPRvB+qlBJoS1UZDjNPQNWvGc+Lk
3l8m71+9ABUmPl3eS4Pfbk3aVQZfsXQerQZwK9EZXyoInhvYrixWf6D5u9sXwqB/
kux4RCSbViwZe3pbOy2eguEkO84xa+nfHQTwjj3/FwsUOEu0IhFmZUyGmQTot/lH
vZqGo1BZPSWoAdd1Lg+HM5UyWn8y5SbyZRCKvz7qqyc91ROyksCaHr0gVTWA/iNS
+W3H2s+FB62Q9fmIU4sv
=x322
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.12/devicetree-fixes-2' of http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 4.12,
please pull the following:
- Phil provides a fix for the BCM283x (Raspberry Pi) by flagging the first
4KiB of physical memory as a reserved region in order to let the secondary
cores successfully spin until they are brought online
* tag 'arm-soc/for-4.12/devicetree-fixes-2' of http://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Reserve first page for firmware
Signed-off-by: Olof Johansson <olof@lixom.net>
on DaVinci. Some resources were getting freed prematurely.
And there was an issue with resources not being on error.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6J2I
-----END PGP SIGNATURE-----
Merge tag 'davinci-fixes-for-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
These fix issues with power management initialization code
on DaVinci. Some resources were getting freed prematurely.
And there was an issue with resources not being on error.
* tag 'davinci-fixes-for-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: PM: Do not free useful resources in normal path in 'davinci_pm_init'
ARM: davinci: PM: Free resources in error handling path in 'davinci_pm_init'
Signed-off-by: Olof Johansson <olof@lixom.net>
Property 'enable-active-low' does not exist. Only 'enable-active-high' is
valid, and when this property is absent the gpio regulator will act as
active low by default.
So remove the unexisting 'enable-active-low' property.
Currently the GPIO flag is GPIO_ACTIVE_HIGH. In order to make
the dts description accurate, pass the GPIO_ACTIVE_LOW flag instead.
This change is safe because the gpio regulator driver does not take the
GPIO flag polarity into account.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Property 'enable-active-low' does not exist. Only 'enable-active-high' is
valid, and when this property is absent the gpio regulator will act as
active low by default.
So remove the unexisting 'enable-active-low' property.
Currently the GPIO flag is 0, which means active-high. In order to make
the dts description accurate, pass the GPIO_ACTIVE_LOW flag instead.
This change is safe because the gpio regulator driver does not take the
GPIO flag polarity into account.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the following eMMC error is seen:
mmc1: mmc_select_hs200 failed, error -74
On imx7d-pico the eMMC VCCQ is fixed at 3.15V, so pass the 'no-1-8-v'
property to properly describe that 1.8V operation is not possible.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d-pico has the WDOG1_B pin connected to the PMIC, so add the
wdog1 node and use the 'fsl,ext-reset-output' property to
properly describe it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Most of DT files in ARM use #include "..." to make pre-processor
include DT in the same directory, but we have some exceptional files
that use #include <...> for that.
Fix them to remove -I$(srctree)/arch/$(SRCARCH)/boot/dts path from
dtc_cpp_flags.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We have a clock controller for the Gemini SoC, so make use of the
driver and add clocks to the peripherals. Remove the hard-coded
frequency from the UART and add switch the timer compatible to the
generic that uses the clock framework for clock speed look-up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the Gemini reset controller to the Gemini SoC
DTSI file and also adds the reset references to all existing
blocks already in the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We cannot use bits from configuration registers as API between
platforms and driver like this, abstract it out to two enums
and mimic the stuff passed as device tree data.
This is done to make it possible for the driver to generate the
ccfg word on-the-fly so we can support more PL08x derivatives.
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Multiple line formats are not preferred as the second and
subsequent lines may not have timestamps.
Lacking timestamps makes reading the output a bit difficult.
This also makes arm/arm64 output more similar.
Previous:
[ 1514.093231] pc : [<bf79c304>] lr : [<bf79ced8>] psr: a00f0013
sp : ecdd7e20 ip : 00000000 fp : ffffffff
New:
[ 1514.093231] pc : [<bf79c304>] lr : [<bf79ced8>] psr: a00f0013
[ 1514.105316] sp : ecdd7e20 ip : 00000000 fp : ffffffff
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Commit 9da5ac236d ("ARM: soft-reboot into same mode that we entered
the kernel") added support to enter the new kernel in the same processor
mode as the previous one when we soft-reboot from one kernel into
another by pass a flag to cpu_reset() so it knows what to do exactly.
However it missed to make similar changes in MCPM code. Due to the
missing flag, the CPUs enter HYP mode which is not supported with MCPM.
MCPM works only in secure mode as it manages CCI.
This patch aligns the cpu_reset call in MCPM with other changes in the
above mentioned commit by making phys_reset_t to follow the prototype
of cpu_reset().
Fixes: 9da5ac236d ("ARM: soft-reboot into same mode that we entered the kernel")
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
We don't need to stop a specific VCPU when changing the active state,
because private IRQs can only be modified by a running VCPU for the
VCPU itself and it is therefore already stopped.
However, it is also possible for two VCPUs to be modifying the active
state of SPIs at the same time, which can cause the thread being stuck
in the loop that checks other VCPU threads for a potentially very long
time, or to modify the active state of a running VCPU. Fix this by
serializing all accesses to setting and clearing the active state of
interrupts using the KVM mutex.
Reported-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To enable smp_processor_id() and might_sleep() debug checks earlier, it's
required to add system states between SYSTEM_BOOTING and SYSTEM_RUNNING.
Adjust the system_state check in ipi_cpu_stop() to handle the extra states.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20170516184735.020718977@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This moves the mcp23s08 driver from gpio to pinctrl. Actual
pinctrl support for configuration of the pull-up resistors
follows in its own patch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable support for USB audio and video camera devices.
Tested on OMAP-L138 LCDK using Logitech webcam and
Plantronics headset.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
davinci_all_defconfig is out of sync with savedefconfig in some places.
Regenerate the default settings by:
$ make davinci_all_config
$ make savedefconfig
$ cp defconfig arch/arm/configs/davinci_all_defconfig
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The DSP subsystem on DA8xx has various internal RAM memories that can
accessed from the ARM side. These memories can be configured to be
used as either RAM or Cache. Add these memories as IOMEM resources
to the DSP device so that the driver can support loading of images
into internal memories.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add names to the IOMEM resources for the DSP device present on
DA8xx SoCs. This will facilitate the driver to use the names and
be agnostic of the resource order, and facilitate scalable DT
support in follow-up patches.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The DSP device on Davinci platforms does not have an MMU and requires
specific DDR memory to boot. This memory is reserved using the rproc_mem
kernel boot parameter and is assigned to the device on non-DT boots.
The remoteproc core uses the DMA API and so will fall back to assigning
random memory if this memory is not assigned to the device, but the DSP
remote processor boot will not be successful in such cases. So, check
that memory has been reserved and assigned to the device specifically
before even creating the DSP device.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The Cubietruck Plus has an optical SPDIF out connector.
Enable SPDIF audio output for this board.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Cubietruck Plus has 4 LEDs in different colors.
Add device nodes for them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T SoC has an SPDIF transmitter block. According to the vendor
BSP kernel, it is compatible with the one found on the H3 SoC.
Add a device node and pinmux setting for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T SoC has a DMA controller that supports 8 DMA channels
to and from various peripherals.
Add a device node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
"bcrmf" is a typo and "wifi" is the preferred form to describe
such node, so change it accordingly.
Reported-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add barebones dts support for TI's K2G Industrial Communication Engine evm.
This dts allows the board to boot using a ram based filesystem.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
With the new Keystone 2 Industrial Communication EVM adding the
unit address to the memory node it made sense to add it for this board
also.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Adding the unit address to the memory node was causing the below error:
Warning (reg_format): "reg" property in /memory has invalid length
(8 bytes) (#address-cells == 2, #size-cells == 2)
Further debugging showed that this was due to the memory node added by
default to skeleton.dtsi which was being included in keystone-k2g.dtsi.
Adding a missing node was all that was needed to remove this deprecated
dtsi file from the SoC dtsi. With skeleton.dtsi removed the dtc compiler
no longer complained about including the unit address for the memory node.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
"bcrmf" is a typo and "wifi" is the preferred form to describe
such node, so change it accordingly.
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the following eMMC error is seen:
mmc1: mmc_select_hs200 failed, error -74
mmc1: new MMC card at address 0001
mmcblk1: mmc1:0001 V10008 7.05 GiB
mmcblk1boot0: mmc1:0001 V10008 partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 V10008 partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 V10008 partition 3 4.00 MiB
On imx7s-warp the eMMC VCCQ is fixed at 3.15V, so pass the 'no-1-8-v'
property to properly describe that 1.8V operation is not possible.
With this change HS200 error is gone and another benefit is that the
card can operate in DDR52 mode now:
mmc1: new DDR MMC card at address 0001
mmcblk1: mmc1:0001 V10008 7.05 GiB
mmcblk1boot0: mmc1:0001 V10008 partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 V10008 partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 V10008 partition 3 4.00 MiB
Suggested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the initial support for imx7d-pico board.
Add support for eMMC, USB host, USB device, PMIC, Ethernet and audio.
For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PWM driver has now capability to specify the PWM polarity
which is e.g. for backlight control. Allow to make use of PWM
polarity by specifying pwm-cells to be 3 in the base dt.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GPCv2 IP block is a part of i.MX7 SoC. Select it to make corresponding
driver availible to support DT changes following this patch.
Cc: yurovsky@gmail.com
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
List GPR block as compatible "fsl,imx6q-iomuxc-gpr" to support drivers
requesting it that way (PCIe driver is one example).
Cc: yurovsky@gmail.com
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that support for 'anatop-enable-bit' has been added to ANADIG
driver, reintroduce 'anatop-enable-bit' for all applicable LDOs.
Cc: yurovsky@gmail.com
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add reference to the Mali GPU device tree node on rk3288-veyron.
Tested on Minnie and Jerry boards.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add reference to the Mali GPU device tree node on rk3288-firefly.
Tested on Firefly board.
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add reference to the Mali GPU device tree node on the
rk3288-rock2-som platform. Tested on a Radxa Rock2 Square board.
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
ARM:
- A fix for a build failure introduced in -rc1 when tracepoints are
enabled on 32-bit ARM.
- Disabling use of stack pointer protection in the hyp code which can
cause panics.
- A handful of VGIC fixes.
- A fix to the init of the redistributors on GICv3 systems that
prevented boot with kvmtool on GICv3 systems introduced in -rc1.
- A number of race conditions fixed in our MMU handling code.
- A fix for the guest being able to program the debug extensions for
the host on the 32-bit side.
PPC:
- Fixes for build failures with PR KVM configurations.
- A fix for a host crash that can occur on POWER9 with radix guests.
x86:
- Fixes for nested PML and nested EPT.
- A fix for crashes caused by reserved bits in SSE MXCSR that could
have been set by userspace.
- An optimization of halt polling that fixes high CPU overhead.
- Fixes for four reports from Dan Carpenter's static checker.
- A protection around code that shouldn't have been preemptible.
- A fix for port IO emulation.
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJZHzY3AAoJEED/6hsPKofocI8H/AiOHXi6AC/3s9Ok3IbN/Wp6
+xSm1yqgxitGhpmKIJQyKMUTV0t8SblRV2nxvW7/MEyfl7vztiyWENaVFc6pO6N7
GbnLvdImZ9aypoBaxVOY8WG/CHw2XZ7oUYyBIGrWECH3k+fptBNdISFK3D76+4G2
+tAuWSpKSQFwjGxtreUSlnvQBp6Tjh/PqTyxslPs4zYCL6UPKSSVAoxy4yOKj3AX
G03tx/1U1n/hSJHub9RFqho4dhVGT/p3V6oppZmS1g/ZqGPQwK1wxlYquHOtORFR
Iq8LdkNQwTdkLlTTOG+tamYSfzn0+KhczfWjIh6ZEb79ARrUSnBU4Awpvom1C2A=
=B6Rl
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- a fix for a build failure introduced in -rc1 when tracepoints are
enabled on 32-bit ARM.
- disable use of stack pointer protection in the hyp code which can
cause panics.
- a handful of VGIC fixes.
- a fix to the init of the redistributors on GICv3 systems that
prevented boot with kvmtool on GICv3 systems introduced in -rc1.
- a number of race conditions fixed in our MMU handling code.
- a fix for the guest being able to program the debug extensions for
the host on the 32-bit side.
PPC:
- fixes for build failures with PR KVM configurations.
- a fix for a host crash that can occur on POWER9 with radix guests.
x86:
- fixes for nested PML and nested EPT.
- a fix for crashes caused by reserved bits in SSE MXCSR that could
have been set by userspace.
- an optimization of halt polling that fixes high CPU overhead.
- fixes for four reports from Dan Carpenter's static checker.
- a protection around code that shouldn't have been preemptible.
- a fix for port IO emulation"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (27 commits)
KVM: x86: prevent uninitialized variable warning in check_svme()
KVM: x86/vPMU: fix undefined shift in intel_pmu_refresh()
KVM: x86: zero base3 of unusable segments
KVM: X86: Fix read out-of-bounds vulnerability in kvm pio emulation
KVM: x86: Fix potential preemption when get the current kvmclock timestamp
KVM: Silence underflow warning in avic_get_physical_id_entry()
KVM: arm/arm64: Hold slots_lock when unregistering kvm io bus devices
KVM: arm/arm64: Fix bug when registering redist iodevs
KVM: x86: lower default for halt_poll_ns
kvm: arm/arm64: Fix use after free of stage2 page table
kvm: arm/arm64: Force reading uncached stage2 PGD
KVM: nVMX: fix EPT permissions as reported in exit qualification
KVM: VMX: Don't enable EPT A/D feature if EPT feature is disabled
KVM: x86: Fix load damaged SSEx MXCSR register
kvm: nVMX: off by one in vmx_write_pml_buffer()
KVM: arm: rename pm_fake handler to trap_raz_wi
KVM: arm: plug potential guest hardware debug leakage
kvm: arm/arm64: Fix race in resetting stage2 PGD
KVM: arm/arm64: vgic-v3: Use PREbits to infer the number of ICH_APxRn_EL2 registers
KVM: arm/arm64: vgic-v3: Do not use Active+Pending state for a HW interrupt
...
Add Mali GPU device tree node for the rk3288 SoC, with devfreq
opp table.
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Property 'enable-active-low' does not exist. Only 'enable-active-high' is
valid, and when this property is absent the gpio regulator will act as
active low by default.
So remove the unexisting 'enable-active-low' property.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change the Northstar Plus Kconfig to select THERMAL and THERMAL_OF,
which allows the ns-thermal driver to be selected via menuconfig.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Update freq of tsadc's working clock as 32768 hz, if not set, tsadc
will work at a default frequence.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds a new opp table for cpu on rk322x SoC.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Set sane default frequencies for CPLL, GPLL and some other core clocks
on the rk322x.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The datasheets for Allwinner SoCs set strict requirements on the
stability of the external crystal oscillators. Add the accuracy
for the main 24MHz oscillator to the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have support for the A83T CCU, add a device node for it,
and replace any existing placeholder clock phandles with the correct
ones.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A10s Olinuxino has an HDMI connector. Make sure we can use it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The A10s has an HDMI controller connected to the second TCON channel. Add
it to our DT.
Since the TV Encoder was the only channel 1 user so far, also add the
property now that we have several users.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Replaced CLK_PLL_VIDEO[01]_2X with raw numbers for now
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
for various devices. Also included is a memory controller (GPMC) debug output
fix as without that the shown bootloader configured GPMC bus width will
be wrong and won't work for kernel timings:
- Add dra7 powerhold configuration to be able to shut down pmic correctly
- Fix polarity for gta04 mcbsp4 clocks for modem
- Fix Pandaboard CEC pin pull making it usable
- Fix LogicPD Torpedo camera pin mux
- Fix GPMC debug bus width
- Reduce cpu thermal shutdown temperature
-----BEGIN PGP SIGNATURE-----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=My0U
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.12/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.12-rc cycle most consisting of few minor dts fixes
for various devices. Also included is a memory controller (GPMC) debug output
fix as without that the shown bootloader configured GPMC bus width will
be wrong and won't work for kernel timings:
- Add dra7 powerhold configuration to be able to shut down pmic correctly
- Fix polarity for gta04 mcbsp4 clocks for modem
- Fix Pandaboard CEC pin pull making it usable
- Fix LogicPD Torpedo camera pin mux
- Fix GPMC debug bus width
- Reduce cpu thermal shutdown temperature
* tag 'omap-for-v4.12/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7: Reduce cpu thermal shutdown temperature
memory: omap-gpmc: Fix debug output for access width
ARM: dts: LogicPD Torpedo: Fix camera pin mux
ARM: dts: omap4: enable CEC pin for Pandaboard A4 and ES
ARM: dts: gta04: fix polarity of clocks for mcbsp4
ARM: dts: dra7: Add power hold and power controller properties to palmas
Signed-off-by: Olof Johansson <olof@lixom.net>
- A fix on GPCv2 power domain driver Kconfig which causes a build
failure when CONFIG_PM is not set.
- Pull down PMIC IRQ pin for imx53-qsrb board to prevent spurious
PMIC interrupts from happening.
- Remove board level OPP override for imx6sx-sdb to fix a boot crash
seen on Rev.C boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZHav8AAoJEFBXWFqHsHzOPWMH/RP4LuJDUoFaPUJ3WsrMhPYR
qmBEzZXvjKBxImFCIiG09vcjQIiN9p5uZ9AqNIQGgoW20DlFKVZ0Rd64MJzp8QnL
J/WwEDTG1qs2jCkNWYkFEUwz6fMWzzTUydj665dkQI3SNwRAJ9dE0LgybM6Yws3C
FQdIUyWR2z8QQYqjLTD9XuDe7ewyoslvFssWRiVzpcnkiu8sWgbTuJ/K+ISCgwo4
rC6Vi7Z4WU47SgL7+d9sOMzDPDIif5mOdfW8uG3tgCeDp/8WNz9IbamCuxhggQpa
+k9jaTHAtOV9ypf1PBUCGHazU7E8hc42XoW6XT0yY3sFynw+VPd1IFVXiWAEBu0=
=gQA8
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.12:
- A fix on GPCv2 power domain driver Kconfig which causes a build
failure when CONFIG_PM is not set.
- Pull down PMIC IRQ pin for imx53-qsrb board to prevent spurious
PMIC interrupts from happening.
- Remove board level OPP override for imx6sx-sdb to fix a boot crash
seen on Rev.C boards.
* tag 'imx-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: add PM dependency for IMX7_PM_DOMAINS
ARM: dts: imx6sx-sdb: Remove OPP override
ARM: dts: imx53-qsrb: Pulldown PMIC IRQ pin
Signed-off-by: Olof Johansson <olof@lixom.net>
It makes sense to have a stripped-down defconfig for just Gemini, as
it is a pretty small platform used in NAS etc, and will use appended
device tree. It is also quick to compile and test. Hopefully this
defconfig can be a good base for distributions such as OpenWRT.
I plan to add in the config options needed for the different
variants of Gemini as we go along.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
4.12, please pull the following:
- Baruch provides several fixes for the Raspberry Pi (BCM2835) Device
Tree source include file: uart0 pinctrl node names, pin number for
i2c0, uart0 rts/cts pins and invalid uart1 pin, missing numbers for
ethernet aliases
-----BEGIN PGP SIGNATURE-----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=6jUO
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.12/devicetree-fixes' of http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for
4.12, please pull the following:
- Baruch provides several fixes for the Raspberry Pi (BCM2835) Device
Tree source include file: uart0 pinctrl node names, pin number for
i2c0, uart0 rts/cts pins and invalid uart1 pin, missing numbers for
ethernet aliases
* tag 'arm-soc/for-4.12/devicetree-fixes' of http://github.com/Broadcom/stblinux:
ARM: dts: bcm2835: add index to the ethernet alias
ARM: dts: bcm2835: fix uart0/uart1 pins
ARM: dts: bcm2835: fix i2c0 pins
ARM: dts: bcm2835: fix uart0 pinctrl node names
Signed-off-by: Olof Johansson <olof@lixom.net>
We use a directory under arch/$ARCH/boot/dts as an include path
that has links outside of the subtree to find dt-bindings from under
include/dt-bindings. That's been working well, but new DT architectures
haven't been adding them by default.
Recently there's been a desire to share some of the DT material between
arm and arm64, which originally caused developers to create symlinks or
relative includes between the subtrees. This isn't ideal -- it breaks
if the DT files aren't stored in the exact same hierarchy as the kernel
tree, and generally it's just icky.
As a somewhat cleaner solution we decided to add a $ARCH/ prefix link
once, and allow DTS files to reference dtsi (and dts) files in other
architectures that way.
Original approach was to create these links under each architecture,
but it lead to the problem of recursive symlinks.
As a remedy, move the include link directories out of the architecture
trees into a common location. At the same time, they can now share one
directory and one dt-bindings/ link as well.
Fixes: 4027494ae6 ('ARM: dts: add arm/arm64 include symlinks')
Reported-by: Russell King <linux@armlinux.org.uk>
Reported-by: Omar Sandoval <osandov@osandov.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: linux-arch <linux-arch@vger.kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZF2pwAAoJEHm+PkMAQRiG9aAIAJJyV6Ux9kaX+glqO3KIs0wm
0K/yqMOv1JTfJ1UUgY4iZbk5XOPPmXv1bdKJFECZfuAHdymJUF/RVNNvDlZbaLdd
K8vDEi92eRwcf07a5b/Q2F8yNfADKKmRAA/oAbuQLBhJ0dPHig70PIvi9gq9kqiE
Ft1MinbsZLavYatLm7oVDr/nsYebEDMGwTy0EX5bF2YjydfAlCvVWnI5ld5wisiV
0fQF4W7MMjjcpAzG8uq3atEB8iQcWS2Ykz2chZRbYzHcdV2WJW751Vge9xc05Hzi
rxlqn6peZFiFyM0qdPLhY0ktGzSTZcCFeb3aZicvm5aOamy2KJjOSZrEwjU8kts=
=VHpx
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rc1' into fixes
We've received a few fixes branches with -rc1 as base, but our contents was
still at pre-rc1. Merge it in expliticly to make 'git merge --log' clear on
hat was actually merged.
Signed-off-by: Olof Johansson <olof@lixom.net>
On imx6sx-sdb rev B/C the VDD_ARM_IN and VDD_SOC_IN supplies are connected
together and both are supplied by the SW1A PMIC output, so model this
correctly in the device tree.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Allwinner V3s SoC has a SPI controller, muxed with the MMC2 controller
at PC bank. The controller itself is identical to the one in H3 SoC.
Add device tree node and the only pinmux node for it.
Tested with a Winbond W25Q128FV SPI NOR soldered on the Lichee Pi
early sample.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Lichee Pi Zero board has a "dock board" which needs to be soldered
with the 1.27mm stamp holes on a Lichee Pi Zero board.
It features:
- Onboard MIC and headphone jack (not supported yet)
- Ethernet port (not supported yet)
- An extra MicroSD slot connected to MMC1 controller
- four keys connected to the LRADC.
As it needs to be soldered with the main board to use, add a stand-alone
device tree for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add secondary pinctrl set for UART2 which can be used to prevent conflicts
with sdmmc pins.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Correct UART2 PINCTRL flag to use the correct pull up setting
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Refer to Chapter 5.3.2 of rk3229 TRM, we can see that GPIO1A[2,4,5]
using RK_FUNC_2 not RK_FUNC_1. This patch fixes it.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On dra7, as per TRM, the HW shutdown (TSHUT) temperature is hardcoded
to 123C and cannot be modified by SW. This means when the temperature
reaches 123C HW asserts TSHUT output which signals a warm reset.
This reset is held until the temperature goes below the TSHUT low (105C).
While in SW, the thermal driver continuously monitors current temperature
and takes decisions based on whether it reached an alert or a critical point.
The intention of setting a SW critical point is to prevent force reset by HW
and instead do an orderly_poweroff(). But if the SW critical temperature is
greater than or equal to that of HW then it defeats the purpose. To address
this and let SW take action before HW does keep the SW critical temperature
less than HW TSHUT value.
The value for SW critical temperature was chosen as 120C just to ensure
we give SW sometime before HW catches up.
Document reference
SPRUI30C – DRA75x, DRA74x Technical Reference Manual - November 2016
SPRUHZ6H - AM572x Technical Reference Manual - November 2016
Tested on:
DRA75x PG 2.0 Rev H EVM
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds a new node to the LEGO MINDSTORMS EV3 device tree for the battery.
Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: minor headline fix]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This enables the power supply module for the LEGO MINDSTORMS EV3 battery.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
It is wrong to iounmap resources in the normal path of davinci_pm_init()
The 3 ioremap'ed fields of 'pm_config' can be accessed later on in other
functions, so we should return 'success' instead of unrolling everything.
Fixes: aa9aa1ec2d ("ARM: davinci: PM: rework init, remove platform device")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[nsekhar@ti.com: commit message and minor style fixes]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
sdcard access with the sdhost controller is faster.
Read access (dd with 64k blocks on rpi2):
CONFIG_MMC_SDHCI_IPROC: 11-12 MB/s
CONFIG_MMC_BCM2835: 19-20 MB/s
Differences on write access are pretty much in the noise.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Eric Anholt <eric@anholt.net>
If we have Linux installed in eMMC we can boot without
µSD card, but inserting one is not recognised.
The reason is that the card detect gpio (gpio5_152)
is not configured and attached to the mmc1 interface
driver and the mmc driver does not poll by default.
Hence we add pinmux and gpio setup for the SDCARD_NCD
signal.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Droid 4 has WL 1285C connected to the OMAP's UART4 port, which is
used for Bluetooth and most likely can also be used for controlling
the FM radio and GPS receivers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
USB1 port is micro-AB type and can function as peripheral
as well as host. Enable dual-role mode for USB1.
We don't want to use the OTG controller block on this
platform as it limits host mode to high-speed. Instead
we rely on extcon framework to give us ID events for
dual-role mode detection.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_pm_clkdms_setup gets called from pm init functions and now that
pm33xx and pm43xx can be loaded as modules this must be kept to be
called at any point during runtime.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP timer code registers two timers - one as clocksource
and one as clockevent. Since AM33XX has only one usable timer
in the WKUP domain one of the timers needs suspend-resume
support to restore the configuration to pre-suspend state.
commit adc78e6b99 ("timekeeping: Add suspend and resume
of clock event devices") introduced .suspend and .resume
callbacks for clock event devices. Leverage these
callbacks to have AM33XX clockevent timer behave properly
across system suspend. Extend the use of the .suspend and
.resume callbacks used by am335x clockevent to am437x as well.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM43XX has the same wakeupgen IP as OMAP4/5. The only
notable difference is the presence of 7 register banks
and lack of SAR area which has been used in OMAP4/5 for
saving and restoring the context around low power states.
In case of AM43XX the context is saved and restored by
the kernel. Introduce wakeupgen_ops so that context save
and restore can be set on a per-SoC basis during init.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The rv4162 compatbile string is missing the vendor part, add it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix commit 05c4ffc3a2 ("ARM: dts: LogicPD Torpedo: Add MT9P031 Support")
In the previous commit, I indicated that the only testing was done by
showing the camera showed up when probing. This patch fixes an incorrect
pin muxing on cam_d0, cam_d1 and cam_d2.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CEC pin was always pulled up, making it impossible to use it.
Change to PIN_INPUT so it can be used by the new CEC support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The clock polarity setting of the mcbsp connected to
the modem was wrong so almost only noise
was received.
With this patch it is also the same as it was on
earlier non-dt kernels where it was working properly
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add power hold and power controller properties to palmas node.
This is needed to shutdown pmic correctly on boards with
powerhold set.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When KVM panics, it hurridly restores the host context and parachutes
into the host's panic() code. This looks like it was copied from arm64,
the 32bit KVM panic code needs to restore the host's banked registers
too.
At some point panic() touches the physical timer/counter, this will
trap back to HYP. If we're lucky, we panic again.
Add a __timer_save_state() call to KVMs hyp_panic() path, this saves the
guest registers and disables the traps for the host.
Fixes: c36b6db5f3 ("ARM: KVM: Add panic handling code")
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
As suggested by Eduardo Valentin this adds the thermal zone for
the bcm2835 SoC with its single thermal sensor. We start with
the criticial trip point and leave the cooling devices empty
since we don't have any at the moment. Since the coefficients
could vary depending on the SoC we need to define them separate.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Raspbian and Fedora have decided to support the Pi3 in 32-bit mode for
now, so it's useful to be able to test that mode on an upstream
kernel. It's also been useful for me to use the same board for 32-bit
and 64-bit development.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Olof Johansson <olof@lixom.net>
The Raspberry Pi startup stub files for multi-core BCM283X processors
make the secondary CPUs spin until the corresponding mailbox is
written. These stubs are loaded at physical address 0x00000xxx (as seen
by the ARMs), but this page will be reused by the kernel unless it is
explicitly reserved, causing the waiting cores to execute random code.
Use the /memreserve/ Device Tree directive to mark the first page as
off-limits to the kernel.
See: https://github.com/raspberrypi/linux/issues/1989
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Enable the new Exynos pseudo random number generator driver and
user-space API to access crypto algorithms and devices (not only RNG).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable the new Exynos pseudo random number generator driver and
user-space API to access crypto algorithms and devices (not only RNG).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
During my research I found that some of the requirements for the memory
buffers for MFC v6+ devices were blindly copied from the previous (v5)
version and simply turned out to be excessive. The relaxed requirements
are applied by the recent patches to the MFC driver and the driver is
now fully functional even without the reserved memory blocks for all
v6+ variants. This patch removes those reserved memory nodes from all
boards having MFC v6+ hardware block.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The MXS LRADC driver left staging and has been split. So re-enable
the driver and remove the obsolete entries.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order to support systemd we need to enable CONFIG_CGROUPS.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pm_fake doesn't quite describe what the handler does (ignoring writes
and returning 0 for reads).
As we're about to use it (a lot) in a different context, rename it
with a (admitedly cryptic) name that make sense for all users.
Signed-off-by: Zhichao Huang <zhichao.huang@linaro.org>
Reviewed-by: Alex Bennee <alex.bennee@linaro.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Hardware debugging in guests is not intercepted currently, it means
that a malicious guest can bring down the entire machine by writing
to the debug registers.
This patch enable trapping of all debug registers, preventing the
guests to access the debug registers. This includes access to the
debug mode(DBGDSCR) in the guest world all the time which could
otherwise mess with the host state. Reads return 0 and writes are
ignored (RAZ_WI).
The result is the guest cannot detect any working hardware based debug
support. As debug exceptions are still routed to the guest normal
debug using software based breakpoints still works.
To support debugging using hardware registers we need to implement a
debug register aware world switch as well as special trapping for
registers that may affect the host state.
Cc: stable@vger.kernel.org
Signed-off-by: Zhichao Huang <zhichao.huang@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
When running a stress playback/stop loop test on a mx6colibri channel
swaps can be noticed randomly.
Increasing the SGTL5000 LRCLK pad strength to its maximum value fixes
the issue, so add the 'lrclk-strength' property to avoid the audio
channel swaps.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When running a stress playback/stop loop test on a mx6wandboard channel
swaps can be noticed randomly.
Increasing the SGTL5000 LRCLK pad strength to its maximum value fixes
the issue, so add the 'lrclk-strength' property to avoid the audio
channel swaps.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the Controller Area Network (MCAN) driver compilation
for sama5 default configuration. Is used by sama5d2 SoC for instance.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If the backup sram allocation fails, ensure we can suspend by falling back
to the usual slow clock mode.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Wenyou Yang <wenyou.yang@atmel.com>
While we can only select between "standby" and "mem" states for power
management, the atmel platforms can actually support more modes.
For both standby and mem, allow selecting which mode will be used using the
atmel.pm_modes kernel parameter.
By default, keep the current modes.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Wenyou Yang <wenyou.yang@atmel.com>
The sama5d2 has a mode were it is possible to cut power to the SoC while
keeping the RAM in self refresh.
Resuming from that mode needs support in the firmware/bootloader.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Wenyou Yang <wenyou.yang@atmel.com>
This enables by default the high resolution timers on sama5d2 platforms.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This makes Atmel sama5 platforms' system tickless when idle.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add nodes to support the Controller Area Network(M_CAN) on SAMA5D2.
The version of M_CAN IP core is 3.1.0 (CREL = 0x31040730).
As said in SAMA5D2 datasheet, the CAN clock is recommended to use
frequencies of 20, 40 or 80 MHz. To achieve these frequencies,
PMC GCLK3 must select the UPLLCK(480 MHz) as source clock and
divide by 24, 12, or 6. So, the "assigned-clock-rates" property
has three options: 20000000, 40000000, and 80000000.
The "assigned-clock-parents" property should be referred to utmi
fixedly.
The MSBs [bits 31:16] of the CAN Message RAM for CAN0 and CAN1 are
default configured in 0x00200000. To avoid conflict with SRAM map
for PM, change them to 0x00210000 in the AT91Bootstrap via setting
the CAN Memories Address-based Register(SFR_CAN) of SFR.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
We like living dangerously. Nothing explicitely forbids stack-protector
to be used in the HYP code, while distributions routinely compile their
kernel with it. We're just lucky that no code actually triggers the
instrumentation.
Let's not try our luck for much longer, and disable stack-protector
for code living at HYP.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
The aa104xd12 and aa121td01 panels are LVDS panels, not DPI panels.
Use the correct DT bindings.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The dock board of Lichee Pi Zero features a MicroSD slot on MMC1, which
can be used with a MicroSD card or the MicroSD-slot Wi-Fi card provided
by Lichee Pi Zero.
Add pinmux for the mmc1 controller, and specify it in the mmc1 device
node as it's the only pinmux for mmc1.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner V3s features a LRADC like the ones in older SoCs.
Add a device tree node for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All the used CCU definitions are stripped from the V3s DTSI file when
it's merged, as the DTSI file and the CCU device tree binding headers
went to different trees.
As they're all in Linus's tree now, restore the usage of the
definitions.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add Sean as one of the authors for the mt7623.dtsi
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add afe nodes to the mt7623.dtsi file. Which
is the necessary node for I2S audio in/out.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add crypto engine nodes to the mt7623.dtsi file.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add USB nodes to the mt7623.dtsi file.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add e/MMC nodes to the mt7623.dtsi file.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add NAND/EEC nodes to the mt7623.dtsi file.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
