[ Upstream commit b7a7943fe2 ]
Fix a memory leak induced by not calling clk_put after doing of_clk_get.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20200907082600.454-3-t-kristo@ti.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b159c63d82 ]
According to the latest RM (see Table 5-1. Clock Root Table),
both usdhc root clocks have the parent order as follows:
000 - 25M_REF_CLK
001 - SYSTEM_PLL1_DIV2
010 - SYSTEM_PLL1_CLK
011 - SYSTEM_PLL2_DIV2
100 - SYSTEM_PLL3_CLK
101 - SYSTEM_PLL1_DIV3
110 - AUDIO_PLL2_CLK
111 - SYSTEM_PLL1_DIV8
So the audio_pll2_out and sys3_pll_out have to be swapped.
Fixes: b80522040c ("clk: imx: Add clock driver for i.MX8MQ CCM")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reported-by: Cosmin Stefan Stoica <cosmin.stoica@nxp.com>
Link: https://lore.kernel.org/r/1602753944-30757-1-git-send-email-abel.vesa@nxp.com
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6c992ca7d ]
In the implementation of bcm2835_register_pll(), the allocated pll is
leaked if devm_clk_hw_register() fails to register hw. Release pll if
devm_clk_hw_register() fails.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Link: https://lore.kernel.org/r/20200809231202.15811-1-navid.emamdoost@gmail.com
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85d071e7f1 ]
SAMA5D2 datasheet specifies on chapter 33.22.8 (PMC Clock Generator
Main Oscillator Register) that writing any value other than
0x37 on KEY field aborts the write operation. Use the key when
selecting main clock parent.
Fixes: 27cb1c2083 ("clk: at91: rework main clk implementation")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1598338751-20607-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b608f11d49 ]
We can get down to this return value from ERR_CAST() without
initializing hw. Set it to -ENOMEM so that we always return something
sane.
Fixes the following smatch warning:
drivers/clk/rockchip/clk-half-divider.c:228 rockchip_clk_register_halfdiv() error: uninitialized symbol 'hw'.
drivers/clk/rockchip/clk-half-divider.c:228 rockchip_clk_register_halfdiv() warn: passing zero to 'ERR_CAST'
Cc: Elaine Zhang <zhangqing@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Fixes: 956060a527 ("clk: rockchip: add support for half divider")
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f05cced73 ]
The DT clock probe loop incorrectly terminates after processing "clocks"
only, fix this by re-starting the loop when all entries for current
DT property have been parsed.
Fixes: 8e48b33f9d ("clk: keystone: sci-clk: probe clocks from DT instead of firmware")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20200907085740.1083-2-t-kristo@ti.com
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d46e5a39f9 ]
This was likely overlooked while porting the driver upstream.
Reported-by: Pavel Dubrova <pashadubrova@gmail.com>
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200922120909.97203-1-konradybcio@gmail.com
Fixes: f2a76a2955 ("clk: qcom: Add Global Clock controller (GCC) driver for SDM660")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c4e80e067 ]
On Amlogic Meson G12b platform, similar to fclk_div3, the fclk_div2
seems to be necessary for the system to operate correctly as well.
Typically, the clock also gets chosen by the eMMC peripheral. This
probably masked the problem so far. However, when booting from a SD
card the clock seems to get disabled which leads to a system freeze.
Let's mark this clock as critical, fixing boot from SD card on G12b
platforms.
Fixes: 085a4ea93d ("clk: meson: g12a: add peripheral clock controller")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/577e0129e8ee93972d92f13187ff4e4286182f67.1598629915.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3bb0f796f ]
The ChipID IO region has it's own clock, which is being disabled while
scanning for unused clocks. It turned out that some CPU hotplug, CPU idle
or even SOC firmware code depends on the reads from that area. Fix the
mysterious hang caused by entering deep CPU idle state by ignoring the
'chipid' clock during unused clocks scan, as there are no direct clients
for it which will keep it enabled.
Fixes: e062b57177 ("clk: exynos4: register clocks using common clock framework")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200922124046.10496-1-m.szyprowski@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5105660ee8 ]
Commit bff1cef5f2 ("clk: tegra: Don't enable already enabled PLLs")
added checks to avoid enabling PLLs that have already been enabled by
the bootloader. However, the PLL_E configuration inherited from the
bootloader isn't necessarily the one that is needed for the kernel.
This can cause SATA to fail like this:
[ 5.310270] phy phy-sata.6: phy poweron failed --> -110
[ 5.315604] tegra-ahci 70027000.sata: failed to power on AHCI controller: -110
[ 5.323022] tegra-ahci: probe of 70027000.sata failed with error -110
Fix this by always programming the PLL_E. This ensures that any mis-
configuration by the bootloader will be overwritten by the kernel.
Fixes: bff1cef5f2 ("clk: tegra: Don't enable already enabled PLLs")
Reported-by: LABBE Corentin <clabbe@baylibre.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc26ed7be4 ]
do_div() macro to perform u64 division and guards against overflow if
the result is too large for the unsigned long return type.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lkml.kernel.org/r/20200114160726.19771-1-dinguyen@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f6ac72946 ]
The buffer allocated in ti_adpll_clk_get_name doesn't account for the
terminating null. This patch switches to devm_kasprintf to avoid
overflowing.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lkml.kernel.org/r/20191019140634.15596-1-steve@sk2.org
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9c006bc78 ]
A new warning in Clang points out that the initialization of
mux_pll_src_4plls_p appears incorrect:
../drivers/clk/rockchip/clk-rk3228.c:140:58: warning: suspicious
concatenation of string literals in an array initialization; did you
mean to separate the elements with a comma? [-Wstring-concatenation]
PNAME(mux_pll_src_4plls_p) = { "cpll", "gpll", "hdmiphy" "usb480m" };
^
,
../drivers/clk/rockchip/clk-rk3228.c:140:48: note: place parentheses
around the string literal to silence warning
PNAME(mux_pll_src_4plls_p) = { "cpll", "gpll", "hdmiphy" "usb480m" };
^
1 warning generated.
Given the name of the variable and the same variable name in rv1108, it
seems that this should have been four distinct elements. Fix it up by
adding the comma as suggested.
Fixes: 307a2e9ac5 ("clk: rockchip: add clock controller for rk3228")
Link: https://github.com/ClangBuiltLinux/linux/issues/1123
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20200810044020.2063350-1-natechancellor@gmail.com
Reviewed-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3dabfa2bda ]
'sizeof(*pllen)' should be used in place of 'sizeof(*pllout)' to avoid a
small over-allocation.
Fixes: 2d17269151 ("clk: davinci: New driver for davinci PLL clocks")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200809144959.747986-1-christophe.jaillet@wanadoo.fr
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f34e4651ce ]
Contrary to previous SoCs, bcm2711 doesn't have a prescaler in the PLL
feedback loop. Bypass it by zeroing fb_prediv_mask when running on
bcm2711.
Note that, since the prediv configuration bits were re-purposed, this
was triggering miscalculations on all clocks hanging from the VPU clock,
notably the aux UART, making its output unintelligible.
Fixes: 42de9ad400 ("clk: bcm2835: Add BCM2711_CLOCK_EMMC2 support")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200730182619.23246-1-nsaenzjulienne@suse.de
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12b90b4085 ]
In case of error, the function clk_register() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20200713032143.21362-1-vulab@iscas.ac.cn
Acked-by: Barry Song <baohua@kernel.org>
Fixes: 7bf21bc81f ("clk: sirf: re-arch to make the codes support both prima2 and atlas6")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8b9002f44 ]
0x44 isn't a register offset, it is the value that goes into CAL_L_VAL.
Fixes: 548a909597 ("clk: qcom: clk-alpha-pll: Add support for Trion PLLs")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-3-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 667f39b59b ]
Fix the parents and set BRANCH_HALT_SKIP. From the downstream driver it
should be a 500us delay and not skip, however this matches what was done
for other clocks that had 500us delay in downstream.
Fixes: f73a4230d5 ("clk: qcom: gcc: Add GPU and NPU clocks for SM8150")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-2-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf8030d703 ]
In order to make the last clock available, maxbit has to be set to the
highest bit value plus 1.
Fixes: 1c099779c1 ("clk: add BCM63XX gated clock controller driver")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20200609110846.4029620-1-noltari@gmail.com
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcd2e0deae ]
Currently we are not initializing the scmi clock with discrete rates
correctly. We fetch the min_rate and max_rate value only for clocks with
ranges and ignore the ones with discrete rates. This will lead to wrong
initialization of rate range when clock supports discrete rate.
Fix this by using the first and the last rate in the sorted list of the
discrete clock rates while registering the clock.
Link: https://lore.kernel.org/r/20200709081705.46084-2-sudeep.holla@arm.com
Fixes: 6d6a1d82ea ("clk: add support for clocks provided by SCMI")
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reported-and-tested-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dad4e7fda4 ]
The current implementation always uses rpmh_write_async, which doesn't
wait for completion. That's fine for disable requests since there's no
immediate need for the clocks and they can be disabled in the
background. However, for enable requests we need to ensure the clocks
are actually enabled before returning to the client. Otherwise, clients
can end up accessing their HW before the necessary clocks are enabled,
which can lead to bus errors.
Use the synchronous version of this API (rpmh_write) for enable requests
in the active set to ensure completion.
Completion isn't required for sleep/wake sets, since they don't take
effect until after we enter sleep. All rpmh requests are automatically
flushed prior to entering sleep.
Fixes: 9c7e47025a ("clk: qcom: clk-rpmh: Add QCOM RPMh clock driver")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lkml.kernel.org/r/20200215021232.1149-1-mdtipton@codeaurora.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sboyd@kernel.org: Reorg code a bit for readability, rename to 'wait' to
make local variable not conflict with completion.h mechanism]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 37c72e4cae upstream.
Add the missing ufs card and ufs phy clocks for SM8150. They were missed
in earlier addition of clock driver.
Fixes: 2a1d7eb854 ("clk: qcom: gcc: Add global clock controller driver for SM8150")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lkml.kernel.org/r/20200513065420.32735-2-vkoul@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f73a4230d5 upstream.
Add the GPU and NPU clocks for SM8150. They were missed in earlier
addition of clock driver.
Fixes: 2a1d7eb854 ("clk: qcom: gcc: Add global clock controller driver for SM8150")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lkml.kernel.org/r/20200513065420.32735-1-vkoul@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c2407ab3bd ]
The EMMC clock can be derived from either the HPLL or the MPLL. Register
a clock mux so that the rate is calculated correctly based upon the
parent.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20200709195706.12741-2-eajames@linux.ibm.com
Acked-by: Joel Stanley <joel@jms.id.au>
Fixes: d3d04f6c33 ("clk: Add support for AST2600 SoC")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e3709d7e3 ]
When building arm32 allmodconfig:
ld.lld: error: undefined symbol: ap_cp_unique_name
>>> referenced by ap-cpu-clk.c
>>> clk/mvebu/ap-cpu-clk.o:(ap_cpu_clock_probe) in archive drivers/built-in.a
ap_cp_unique_name is only compiled into the kernel image when
CONFIG_ARMADA_AP_CP_HELPER is selected (as it is not user selectable).
However, CONFIG_ARMADA_AP_CPU_CLK does not select it.
This has been a problem since the driver was added to the kernel but it
was not built before commit c318ea261749 ("cpufreq: ap806: fix cpufreq
driver needs ap cpu clk") so it was never noticed.
Fixes: f756e362d9 ("clk: mvebu: add CPU clock driver for Armada 7K/8K")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20200701201128.2448427-1-natechancellor@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0a5fdf4cc ]
The (struct __prci_data).hw_clks.hws is an array with dynamic elements.
Using struct_size(pd, hw_clks.hws, ARRAY_SIZE(__prci_init_clocks))
instead of sizeof(*pd) to get the correct memory size of
struct __prci_data for sifive/fu540-prci. After applying this
modifications, the kernel runs smoothly with CONFIG_SLAB_FREELIST_RANDOM
enabled on the HiFive unleashed board.
Fixes: 30b8e27e3b ("clk: sifive: add a driver for the SiFive FU540 PRCI IP block")
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d491066cc ]
The latest specs for the AST2600 A1 chip include some different bit
definitions for calculating the AHB clock divider. Implement these in
order to get the correct AHB clock value in Linux.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lkml.kernel.org/r/20200408203616.4031-1-eajames@linux.ibm.com
Fixes: d3d04f6c33 ("clk: Add support for AST2600 SoC")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2f30986d4 ]
The function _sprd_pll_recalc_rate() defines return value to unsigned
long, but it would return a negative value when malloc fail, changing
to return its parent_rate makes more sense, since if the callback
.recalc_rate() is not set, the framework returns the parent_rate as
well.
Fixes: 3e37b00558 ("clk: sprd: add adjustable pll support")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lkml.kernel.org/r/20200519030036.1785-2-zhang.lyra@gmail.com
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f376c43bec ]
bcm2835_register_gate is used as a callback for the clk_register member
of bcm2835_clk_desc, which expects a struct clk_hw * return type but
bcm2835_register_gate returns a struct clk *.
This discrepancy is hidden by the fact that bcm2835_register_gate is
cast to the typedef bcm2835_clk_register by the _REGISTER macro. This
turns out to be a control flow integrity violation, which is how this
was noticed.
Change the return type of bcm2835_register_gate to be struct clk_hw *
and use clk_hw_register_gate to do so. This should be a non-functional
change as clk_register_gate calls clk_hw_register_gate anyways but this
is needed to avoid issues with further changes.
Fixes: b19f009d45 ("clk: bcm2835: Migrate to clk_hw based registration and OF APIs")
Link: https://github.com/ClangBuiltLinux/linux/issues/1028
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lkml.kernel.org/r/20200516080806.1459784-1-natechancellor@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25bdae0f1c ]
Mark the SCLK clock for Exynos5433 I2S1 device with IGNORE_UNUSED flag to
match its behaviour with SCLK clock for AUD_I2S (I2S0) device until
a proper fix for Exynos I2S driver is ready.
This fixes the following synchronous abort issue revealed by the probe
order change caused by the commit 93d2e4322a ("of: platform: Batch
fwnode parsing when adding all top level devices")
Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 50 Comm: kworker/0:1 Not tainted 5.7.0-rc5+ #701
Hardware name: Samsung TM2E board (DT)
Workqueue: events deferred_probe_work_func
pstate: 60000005 (nZCv daif -PAN -UAO)
pc : samsung_i2s_probe+0x768/0x8f0
lr : samsung_i2s_probe+0x688/0x8f0
...
Call trace:
samsung_i2s_probe+0x768/0x8f0
platform_drv_probe+0x50/0xa8
really_probe+0x108/0x370
driver_probe_device+0x54/0xb8
__device_attach_driver+0x90/0xc0
bus_for_each_drv+0x70/0xc8
__device_attach+0xdc/0x140
device_initial_probe+0x10/0x18
bus_probe_device+0x94/0xa0
deferred_probe_work_func+0x70/0xa8
process_one_work+0x2a8/0x718
worker_thread+0x48/0x470
kthread+0x134/0x160
ret_from_fork+0x10/0x1c
Code: 17ffffaf d503201f f94086c0 91003000 (88dffc00)
---[ end trace ccf721c9400ddbd6 ]---
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c1cbbc92 ]
The parent_names is never released for a component clock definition,
causing some memory leak. Fix by releasing it once it is no longer
needed.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lkml.kernel.org/r/20200429131341.4697-2-t-kristo@ti.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a29ae8600d ]
Not all u-boot versions initialize the HHI_GP_PLL_CNTL[2-5] registers.
In that case all HHI_GPLL_PLL_CNTL[1-5] registers are 0x0 and when
booting Linux the PLL fails to lock.
The initialization sequence from u-boot is:
- put the PLL into reset
- write 0x59C88000 to HHI_GP_PLL_CNTL2
- write 0xCA463823 to HHI_GP_PLL_CNTL3
- write 0x0286A027 to HHI_GP_PLL_CNTL4
- write 0x00003000 to HHI_GP_PLL_CNTL5
- set M, N, OD and the enable bit
- take the PLL out of reset
- check if it has locked
- disable the PLL
In Linux we already initialize M, N, OD, the enable and the reset bits.
Also the HHI_GP_PLL_CNTL[2-5] registers with these magic values (the
exact meaning is unknown) so the PLL can lock when the vendor u-boot did
not initialize these registers yet.
Fixes: b882964b37 ("clk: meson: meson8b: add support for the GP_PLL clock on Meson8m2")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200501215717.735393-1-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bb629cfb2 ]
The DIV{1,2,4,6,12}_EN bits are actually located in HHI_VID_CLK_CNTL
register:
- HHI_VID_CLK_CNTL[0] = DIV1_EN
- HHI_VID_CLK_CNTL[1] = DIV2_EN
- HHI_VID_CLK_CNTL[2] = DIV4_EN
- HHI_VID_CLK_CNTL[3] = DIV6_EN
- HHI_VID_CLK_CNTL[4] = DIV12_EN
Update the bits accordingly so we will enable the bits in the correct
register once we switch these clocks to be mutable.
Fixes: 6cb57c678b ("clk: meson: meson8b: add the read-only video clock trees")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200417184127.1319871-4-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d3051c790 ]
CLKC_RESET_VID_DIVIDER_CNTL_RESET_N_POST and
CLKC_RESET_VID_DIVIDER_CNTL_RESET_N_PRE are active low. This means:
- asserting them requires setting the register value to 0
- de-asserting them requires setting the register value to 1
Set the register value accordingly for these two reset lines by setting
the inverted the register value compared to all other reset lines.
Fixes: 189621726b ("clk: meson: meson8b: register the built-in reset controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200417184127.1319871-3-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da1978ac3d ]
Use hdmi_pll_lvds_out as parent of the vid_pll_in_sel clock. It's not
easy to see that the vendor kernel does the same, but it actually does.
meson_clk_pll_ops in mainline still cannot fully recalculate all rates
from the HDMI PLL registers because some register bits (at the time of
writing it's unknown which bits are used for this) double the HDMI PLL
output rate (compared to simply considering M, N and FRAC) for some (but
not all) PLL settings.
Update the vid_pll_in_sel parent so our clock calculation works for
simple clock settings like the CVBS output (where no rate doubling is
going on). The PLL ops need to be fixed later on for more complex clock
settings (all HDMI rates).
Fixes: 6cb57c678b ("clk: meson: meson8b: add the read-only video clock trees")
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200417184127.1319871-2-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a403bbab1a ]
Fixes an issue leading to having all clocks following a critical
clocks marked as well as criticals.
Fixes: fa6415affe ("clk: st: clk-flexgen: Detect critical clocks")
Signed-off-by: Alain Volmat <avolmat@me.com>
Link: https://lkml.kernel.org/r/20200322140740.3970-1-avolmat@me.com
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ace3420977 ]
On SoCs with Standby Control Registers (STBCRs) instead of Module Stop
Control Registers (MSTPCRs), the suspend handler saves the wrong
registers, and the resume handler prints the wrong register in an error
message.
Fortunately this cannot happen yet, as the suspend/resume code is used
on PSCI systems only, and systems with STBCRs (RZ/A1 and RZ/A2) do not
use PSCI. Still, it is better to fix this, to avoid this becoming a
problem in the future.
Distinguish between STBCRs and MSTPCRs where needed. Replace the
useless printing of the virtual register address in the resume error
message by printing the register index.
Fixes: fde35c9c7d ("clk: renesas: cpg-mssr: Add R7S9210 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200507074713.30113-1-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e47bd937e6 ]
The TOP 'aclk*_isp', 'aclk550_cam', 'gscl_wa' and 'gscl_wb' clocks must
be kept enabled all the time to allow proper access to power management
control for the ISP and CAM power domains. The last two clocks, although
related to GScaler device and GSCL power domain, provides also the
I_WRAP_CLK signal to MIPI CSIS0/1 devices, which are a part of CAM power
domain and are needed for proper power on/off sequence.
Currently there are no drivers for the devices, which are part of CAM and
ISP power domains yet. This patch only fixes the race between disabling
the unused power domains and disabling unused clocks, which randomly
resulted in the following error during boot:
Power domain CAM disable failed
Power domain ISP disable failed
Fixes: 318fa46cc6 ("clk/samsung: exynos542x: mark some clocks as critical")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f47ab3c2f5 ]
During the process of debugging a processor derived from the msm8916 which
we found the new processor was not starting one of its PLLs.
After tracing the addresses and writes that downstream was doing and
comparing to upstream it became obvious that we were writing to a different
register location than downstream when trying to configure the PLL.
This error is also present in upstream msm8916.
As an example clk-pll.c::clk_pll_recalc_rate wants to write to
pll->config_reg updating the bit-field POST_DIV_RATIO. That bit-field is
defined in PLL_USER_CTL not in PLL_CONFIG_CTL. Taking the BIMC PLL as an
example
lm80-p0436-13_c_qc_snapdragon_410_processor_hrd.pdf
0x01823010 GCC_BIMC_PLL_USER_CTL
0x01823014 GCC_BIMC_PLL_CONFIG_CTL
This pattern is repeated for gpll0, gpll1, gpll2 and bimc_pll.
This error is likely not apparent since the bootloader will already have
initialized these PLLs.
This patch corrects the location of config_reg from PLL_CONFIG_CTL to
PLL_USER_CTL for all relevant PLLs on msm8916.
Fixes commit 3966fab8b6 ("clk: qcom: Add MSM8916 Global Clock Controller support")
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lkml.kernel.org/r/20200329124116.4185447-1-bryan.odonoghue@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee25d9742d ]
round_down() can only round to powers of 2. If round_down() is asked
to round to something that is not a power of 2, incorrect results are
produced. The incorrect results can be both too large and too small.
Instead, use rounddown() which can round to any number.
Fixes: 6a721db180 ("clk: sunxi: Add A31 clocks support")
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 571cfadcc6 upstream.
When some new clock supports are introduced, e.g. [1]
it might lead to an error although it should be NULL because
clk_init_data is on the stack and it might have random values
if using without initialization.
Add the missing initial value to clk_init_data.
[1] https://android-review.googlesource.com/c/kernel/common/+/1278046
Fixes: a3ae549917 ("clk: mediatek: Add new clkmux register API")
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1590560749-29136-1-git-send-email-weiyi.lu@mediatek.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64c7d7ea22 upstream.
clk_pm_runtime_get() assumes that the PM-runtime usage counter will
be dropped by pm_runtime_get_sync() on errors, which is not the case,
so PM-runtime references to devices acquired by the former are leaked
on errors returned by the latter.
Fix this by modifying clk_pm_runtime_get() to drop the reference if
pm_runtime_get_sync() returns an error.
Fixes: 9a34b45397 clk: Add support for runtime PM
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a76f274182 ]
Documentation says that gpll0 is parent of gpll0_out_even, somehow
driver coded that as bi_tcxo, so fix it
Fixes: 2a1d7eb854 ("clk: qcom: gcc: Add global clock controller driver for SM8150")
Reported-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lkml.kernel.org/r/20200521052728.2141377-1-vkoul@kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc6dbd5100 ]
Right now, trying to use RTC purely with the ti-sysc / clkctrl framework
fails to enable the RTC module properly. Based on experimentation, this
appears to be because RTC is sourced from the clkdiv32k optional clock.
TRM is not very clear on this topic, but fix the RTC to use the proper
source clock nevertheless.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lkml.kernel.org/r/20200424152301.4018-1-t-kristo@ti.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tero Kristo