This works around a few glitches in the ST version of the PL011
serial driver when using very high baud rates, as we do in the
Ux500: 3, 3.25, 4 and 4.05 Mbps.
Problem Observed/rootcause:
When using high baud-rates, and the baudrate*8 is getting close to
the provided clock frequency (so a division factor close to 1), when
using bursts of characters (so they are abutted), then it seems as if
there is not enough time to detect the beginning of the start-bit which
is a timing reference for the entire character, and thus the sampling
moment of character bits is moving towards the end of each bit, instead
of the middle.
Fix:
Increase slightly the RX baud rate of the UART above the theoretical
baudrate by 5%. This will definitely give more margin time to the
UART_RX to correctly sample the data at the middle of the bit period.
Also fix the ages old copy-paste error in the very stressed comment,
it's referencing the registers used in the PL010 driver rather than
the PL011 ones.
Signed-off-by: Guillaume Jaunet <guillaume.jaunet@stericsson.com>
Signed-off-by: Christophe Arnal <christophe.arnal@stericsson.com>
Signed-off-by: Matthias Locher <matthias.locher@stericsson.com>
Signed-off-by: Rajanikanth HV <rajanikanth.hv@stericsson.com>
Cc: stable <stable@vger.kernel.org>
Cc: Bibek Basu <bibek.basu@stericsson.com>
Cc: Par-Gunnar Hjalmdahl <par-gunnar.hjalmdahl@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel will handle IXON/IXOFF/IXANY in software if the hardware
doesn't do it.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following patch allows users to use KGDB over serial console on
board based on Samsung SOC. It has been tested on a board using
exynos5.
[dianders: changed poll to return NO_POLL_CHAR, which appears to
fix 'help' in kgdb; also updated commit message]
Signed-off-by: Julien Pichon <pichon.jln@gmail.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MAXIDL is the timeout after which a receive buffer is closed when not full if
no more characters are received. We calculate it from the baudrate so that the
duration is always the same at standard rates: about 4ms. At 9600 bauds it gives
a timeout of 4 characters, which is the timeout on the 8250 UART.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
maxidl register was set to fifo size. There is no reason to set this
register to same value as fifo size. Setting it now to 0x10 by default
as in the UCC UART driver.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting the fifo to only 1 byte generates one interrupt every 1ms at 9600 bauds.
This is too much. This patch reduces the threshold to speeds below 2400 bauds
like in the 8250 UART driver.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a desynchronisation problem with CPM UART driver on
Powerpc MPC8xx. The problem happens if data is received before the device
is open by the user application.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently the same card model has two IDs, so this patch
complements the commit 39aced68d6
adding the missing one.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch does the following
- In case of errors if there least one data character in the RX FIFO
read it otherwise it may stall the receiver.
This is recommended in the interrupt reset method in the table 23-246 of
the omap4 TRM.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The legacy serial driver will detect the Winbond CIR device as a serial
port, since it looks exactly like a serial port unless you know what
it is from the PNP ID.
Here we track this port as a special PORT_8250_CIR type, preventing the
legacy serial driver from probing it.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We first probe the legacy serial ports and then check pnp. If there
is a non-standard configuration then this might not work, also this
change is needed so we can blacklist Winbond CIR based on PNP ID.
For this to work the 8250_pnp driver must be merged into the 8250
module.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
remove existing non-dt code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQXBatAAoJEAKiPfwuf9N/VZoIAI7PKNwakjM/KDiVzytwqZ+U
h9kkjYW4ra8MH+jpjFQqvSyIJ3U+t016xqW3ZbqRuZBDgH0I7Gax7QoAZ/ljPlpG
RAKl2l9WVPiBSwCESTpvR5lafBLklk6fL0Z267qIxDGld6YBiWHvTKIh1zDmeCWW
hgDeWtcb1M61VlPrj9nPnCze66h2dUk+QSxaCodv7co5kzb0Q4S7U64BCs0hGe01
kkdoUwnBjdeK0cUhDAJAP1vRyk04N16+H7yp4npmKhv/blKVc3MIRjg1iBV78ncd
Kke/G1B9TJRpNTXdySYnsDQpaCWNSAryKXKkdxP0gh6MW8CMKYc1mdKYcEP3Tk8=
=xG1+
-----END PGP SIGNATURE-----
Merge tag 'vt8500-for-next' of git://git.code.sf.net/p/linuxwmt/code into next/dt
From Tony Prisk:
Update arch-vt8500 and drivers to device tree and
remove existing non-dt code.
* tag 'vt8500-for-next' of git://git.code.sf.net/p/linuxwmt/code:
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
Resolved add/change conflict in drivers/clk/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'for-arm-soc-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
ARM: ux500: Add nodes for the MSP into the HREF Device Tree
ARM: ux500: Add all known I2C sub-device nodes to the HREF DT
ARM: ux500: Stop registering I2C sub-devices for HREF when DT is enabled
ARM: ux500: Stop registering Audio devices for HREF when DT is enabled
ARM: ux500: Add all encompassing sound node to the Snowball Device Tree
ARM: ux500: Add nodes for the MSP into Device Tree
ARM: ux500: Rename MSP board file to something more meaningful
ARM: ux500: Remove platform registration of MSP devices
ARM: ux500: Stop registering the MOP500 Audio driver from platform code
ARM: ux500: Pass MSP DMA platform data though AUXDATA
ARM: ux500: Fork MSP platform registration for step-by-step DT enablement
ARM: ux500: Add AB8500 CODEC node to DB8500 Device Tree
ARM: ux500: Clean-up MSP platform code
ARM: ux500: Pass SDI DMA information though AUX_DATA to MMCI
ARM: ux500: Add UART support to the HREF Device Tree
ARM: ux500: Add skeleton Device Tree for the HREF reference board
...
+ sync to v3.6-rc6
__iomem annotation cleanup branch from Arnd.
* cleanup/__iomem: (21 commits)
net: seeq: use __iomem pointers for MMIO
video: da8xx-fb: use __iomem pointers for MMIO
scsi: eesox: use __iomem pointers for MMIO
serial: ks8695: use __iomem pointers for MMIO
input: rpcmouse: use __iomem pointers for MMIO
ARM: samsung: use __iomem pointers for MMIO
ARM: spear13xx: use __iomem pointers for MMIO
ARM: sa1100: use __iomem pointers for MMIO
ARM: prima2: use __iomem pointers for MMIO
ARM: nomadik: use __iomem pointers for MMIO
ARM: msm: use __iomem pointers for MMIO
ARM: lpc32xx: use __iomem pointers for MMIO
ARM: ks8695: use __iomem pointers for MMIO
ARM: ixp4xx: use __iomem pointers for MMIO
ARM: iop32x: use __iomem pointers for MMIO
ARM: iop13xx: use __iomem pointers for MMIO
ARM: integrator: use __iomem pointers for MMIO
ARM: imx: use __iomem pointers for MMIO
ARM: ebsa110: use __iomem pointers for MMIO
ARM: at91: use __iomem pointers for MMIO
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Drop the check for "up" being valid on suspend/resume callbacks.
It should be valid always. Get rid of the "pdata" check also as
serial_omap_get_context_loss_count() checks for it.
Tested on omap4 panda and 3630 based Beagle board.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_drvdata always retrun a valid value after probe succeed.
It also fixed smatch warnings:
drivers/tty/serial/imx.c:1376 serial_imx_suspend() warn: variable dereferenced before check 'sport' (see line 1372)
drivers/tty/serial/imx.c:1392 serial_imx_resume() warn: variable dereferenced before check 'sport' (see line 1388)
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The autoconfig prints messages while holding the
port's spinlock and that causes a deadlock when
using serial console.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We end up dropping the mutex twice on some errors. We don't want to do
that.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a serial driver is called post hangup with a second DCD event then we
will attempt to get the ldisc of NULL. Check we have a tty before trying to
do anything with it.
This is still only safe within the uart layer if the caller holds the
relevant uart locks. We could do with a version where the tty is passed for
more general use.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase vt8500_max_ports to 6 as the WM8505 as 6 available uarts.
Use devicetree port id as primary addressing for ports but allow
auto-allocation if id not specified.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Alan Cox <alan@linux.intel.com>
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
ARM is moving to stricter checks on readl/write functions,
so we need to use the correct types everywhere.
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Alan says these are not production ready, and users should be told this,
so put the "(EXPERIMENTAL)" marking back in the Kconfig entry string.
Reported-by: Alan Cox <alan@linux.intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As discussed at the kernel summit this year, CONFIG_EXPERIMENTAL means
nothing, so let's get rid of it.
Cc: Kees Cook <keescook@chromium.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Explicitly format uids gids in audit messges in the initial user
namespace. This is safe because auditd is restrected to be in
the initial user namespace.
- Convert audit_sig_uid into a kuid_t.
- Enable building the audit code and user namespaces at the same time.
The net result is that the audit subsystem now uses kuid_t and kgid_t whenever
possible making it almost impossible to confuse a raw uid_t with a kuid_t
preventing bugs.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Paris <eparis@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Always store audit loginuids in type kuid_t.
Print loginuids by converting them into uids in the appropriate user
namespace, and then printing the resulting uid.
Modify audit_get_loginuid to return a kuid_t.
Modify audit_set_loginuid to take a kuid_t.
Modify /proc/<pid>/loginuid on read to convert the loginuid into the
user namespace of the opener of the file.
Modify /proc/<pid>/loginud on write to convert the loginuid
rom the user namespace of the opener of the file.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Paris <eparis@redhat.com>
Cc: Paul Moore <paul@paul-moore.com> ?
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Return the value returned by the failing function instead
of -1 (which does not convey the right error information).
Fixes the following smatch warning:
drivers/tty/serial/samsung.c:1687 s3c24xx_serial_modinit() info:
why not propagate 'ret' from uart_register_driver() instead of -1?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the trace we print the wrong values for N(R) on an I frame.
Correct the mask.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise we start trying to use a bogus channel - ungood.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't want to free a random address if the entry is wrong, cover
this and WARN if it ever happens.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HVC returns a size of -1 bytes for the write room in some cases.
This is bogus and not handled by the tty layer at all.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the imx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
From "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>:
this is the 2nd version of this series whose goal is to make struct
of_device_id.data const. Conceptually a driver must not modify the data
contained there so making it const is the right thing.
v1 of this series was sent with Message-id:
1342182734-321-1-git-send-email-y. Changes since then are:
- powerpc fixes
- several new consts that were found by Arnd that are possible after
patch 19.
Arnd suggested to take this series via arm-soc late for 3.6 in one go
because patch 19 depends on the former patches but is a precondition to
the latter and it fixes a few warnings. So getting it in via the
respective maintainer trees would need a much bigger coordination
effort. That means I prefer getting Acks over you taking the patch.
Vinod Koul already took
dmaengine: at_hdmac: add a few const qualifiers
that is in next-20120723 as 7fd63ccdad now. Vinod, I don't follow your
pull requests, but assuming you didn't let it already pull for 3.6 I
suggest you drop it from your queue and I just take your Ack.
This series was build tested for arm (all defconfigs) and powerpc (all
defconfigs and an allyesconfig) and grep didn't find more issues. As
before it introduces a warning in drivers/regulator/twl-regulator.c.
This driver does modify its .of_match_table when a device is bound which
doesn't fits the concept of independant devices. Arnd noticed another
new warning in drivers/scsi/qlogicpti.c that isn't that easy to resolve,
because the pointer to (now) const data is passed as first argument to
scsi_host_alloc. To fix that properly struct Scsi_Host.hostt needs to
get a const, too. Alternatively I could introduce a cast removing the
const, but I don't like that.
* 'ofdeviceiddata' of git://git.pengutronix.de/git/ukl/linux: (25 commits)
dma: tegra: make data used as *of_device_id.data const
can: mpc5xxx_can: make data used as *of_device_id.data const
macintosh/mediabay: make data used as *of_device_id.data const
i2c/mpc: make data used as *of_device_id.data const
mfd/da9052: make i2c_device_id array const
powerpc/fsl_msi: drop unneeded cast to non-const pointer
gpio/gpio-omap: make platformdata used as *of_device_id.data const
of: add const to struct *of_device_id.data
dma: tegra: make tegra_dma.chip_data a pointer to const data
watchdog/mpc8xxx: add a const qualifier
powerpc/celleb_pci: add a const qualifier
powerpc/fsl_msi: add a const qualifier
powerpc/83xx: add a const qualifier
macintosh/mediabay: add a const qualifier
mmc/omap_hsmmc: add a const qualifier
i2c/mpc: add a const qualifier
i2c/i2c-omap: add a const qualifier
gpio/mpc8xxx: add a const qualifier
gpio/gpio-omap.c: add a const qualifier
misc/atmel_tc: make atmel_tc.tcb_config member point to const data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: repulled a v3 version of the branch that rebased to add some more
acked-bys and added one more patch on top for tegra]
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'x86/platform' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (9690 commits)
x86: Document x86_init.paging.pagetable_init()
x86: xen: Cleanup and remove x86_init.paging.pagetable_setup_done()
x86: Move paging_init() call to x86_init.paging.pagetable_init()
x86: Rename pagetable_setup_start() to pagetable_init()
x86: Remove base argument from x86_init.paging.pagetable_setup_start
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
...
The mxs_auart_probe() gets the device by the get_device().
So we should put the device in the error path to balance the
device's reference counter.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These workarounds do not apply for CONFIG_ARCH_OMAP2PLUS at all,
so let's make it just CONFIG_ARCH_OMAP1.
This is needed to for ARM common zImage changes for
omap2+ to avoid including plat and mach headers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This prepares *of_device_id.data becoming const. Without this change
the following warning would occur:
drivers/tty/serial/mpc52xx_uart.c: In function 'mpc52xx_uart_of_enumerate':
drivers/tty/serial/mpc52xx_uart.c:1440:11: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
On some machines using a specific hardware for console screen output,
the update of the pixel frame buffer does not work correctly when
using command line edition. This may be due to a memory cache bug
in the machine on which the problem has been found, but an other
solution is possible.
This patch proposes to avoid touching directly the pixel frame buffer
and to rebuild each character using the standard putc() function
on command line edition.
The resulting code is smaller and not obviously slower (no read
access to the pixel frame buffer).
Tested on a Cubox (ARM Marvell Dove 88AP510 SoC).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver explicitly requests a clock rate for the UART, but it is
off by a factor of four from the dividers that it programs into the
UART. Fix this by setting the rate to 1/4 of the current value.
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bug flag .interrupt_may_hang is not used since commit
4fd0690bb0
"serial: pl011: implement workaround for CTS clear event issue"
so delete it.
Cc: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dereference should be moved below the NULL test.
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Request pins using pinctrl framework. Only show a warning
on error as some boards set the pins in the bootloader
even if CONFIG_PINCTRL is enabled.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OMAP Architecture code, passes a few function
pointers for UART driver to use in order to
properly implement Power Management and Wakeup
capabilities.
The problem is that those function pointers,
which are passed (ab)using platform_data on
non-DT kernels, can't be passed down to drivers
through DT.
commit e5b57c0 (serial: omap: define helpers
for pdata function pointers) failed to take DT
kernels into consideration and caused a regression
to DT kernel boot.
Fix that by (re-)adding a check for valid pdata
pointer together with valid pdata->$FUNCTION
pointer.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Covers the rest of the uses of pci error handler.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
when rebasing patches on top of Greg's tty-next,
it looks like automerge broke a few things which
I didn't catch (for whatever reason I didn't
have OMAP Serial enabled on .config) so I ended
up breaking the build on Greg's tty-next branch.
Fix the breakage by re-adding the three missing
members on struct uart_omap_port.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added tty_device_create_release() and bound to dev->release in
tty_register_device_attr().
Added tty_port_register_device_attr() and used in uart_add_one_port()
instead of tty_register_device_attr().
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added file /sys/devices/.../tty/ttySX/uartclk to allow reading
uartclk value in struct uart_port in serial_core via sysfs.
tty_register_device() has been generalized and refactored in order
to add support for setting drvdata and attribute_group to the device.
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes these build errors:
In file included from drivers/tty/serial/sccnxp.c:20:0:
include/linux/serial_core.h: In function 'uart_handle_break':
include/linux/serial_core.h:543:30: error: dereferencing pointer to incomplete type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We call the get_device() in the mxs_auart_probe().
For the balance of the reference count, we should put the
device in the mxs_auart_remove().
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After set the AUART_CTRL0_CLKGATE, the UART will gate all the clocks off.
So the following line will not take effect.
................................................................
writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN,
u->membase + AUART_INTR_CLR);
................................................................
To fix this issue, the patch moves this gate-off line to
the end of setting registers.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sizeof when applied to a pointer typed expression gives the
size of the pointer.
Generated by: scripts/coccinelle/misc/noderef.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
enable RX FIFO for 16 characters and TX FIFO
for 16 spaces.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nobody needs to access the uart_omap_port structure
other than omap-serial.c file. Let's move that
structure definition to the C source file in order
to prevent anyone from accessing our structure.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this driver doesn't use any from <plat/dmtimer.h>, so
we can remove it without any problems.
This will, however cause a problem because omap-serial.c
was relying on indirect inclusion of <linux/platform_device.h>,
let's fix the issue by including <linux/platform_device.h>
on omap-serial.c as it should be.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Software flow control register bits were not defined correctly.
Also clarify the IXON and IXOFF logic to reflect what userspace wants.
Cc: stable@vger.kernel.org
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if we would reach serial_omap_get_char() while
Data Ready bit isn't set, we would return from
it without kicking our pm timer. This would mean
we would, eventually, have an unbalanced
pm_runtime_get on our device which would prevent
it from ever sleeping again.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has been missing from OMAP UART driver
for quite a while and it's simple enough
to implement it.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch unlocks the port lock before calling a serial_core API
and re-acquires the port lock after calling it.
This patch fixes a system freeze issue seen when the serial_core
API uart_write_wakeup() eventually attempts to acquire the port lock
already acquired by omap serial interrupt handler.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Vijay Badawadagi <bvijay@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
it makes no sense to mark our IRQ handler inline
since it's passed as a function pointer when
enabling the IRQ line.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two functions:
omap_serial_fill_features_erratas() and
of_get_uart_port_info() are only called from probe().
Marking them as __devinit gives us another
oportunity to free some code after .init.text
is done.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_enable() needs to be invoked before
pm_runtime_use_autosuspend(), and
pm_runtime_set_autosuspend_delay() functions.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we're running our hardirq handler, there's
not need to disable IRQs with spin_lock_irqsave()
because IRQs are already disabled. It also makes
no difference if we save or not IRQ flags.
Switch over to simple spin_lock/spin_unlock and
drop the "flags" variable.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
before removing the driver, let's make sure
to force device into a suspended state in order
to conserve power.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if platform_get_drvdata() returns NULL, that's
quite a nasty bug on the driver which we want to
catch ASAP. Otherwise, that check is hugely
unneeded.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
by the time we call our first pm_runtme_get_sync()
after enable pm_runtime, our resume method might
be called. To avoid problems, we must make sure
that our dev->drvdata is set correctly before
our resume method gets called.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Everytime we're done using our TTY, we want
the pm timer to be reinitilized. By sticking
to pm_runtime_pm_autosuspend() we make sure
that this will always be the case.
The idea behind this patch is to make sure we
will always reinitialize the pm timer so that
we don't fall into a situation where pm_runtime_put()
expires right away (if timer was already about to
expire when we made the call to pm_runtime_put()).
While suspending right away wouldn't cause any
issues, reinitializing the pm timer can help us
avoiding unnecessary context save & restore
operations (which are somewhat expensive) if there's
another read/write/set_termios request coming right
after. IOW, we are trying to make sure UART is still
powered up while it's still under heavy usage.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
since all other IRQ types now do all necessary
checks inside their handlers, transmit_chars()
was the only one left expecting serial_omap_irq()
to check THRE for it. We can move THRE check to
transmit_chars() in order to make serial_omap_irq()
more uniform.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
receive_chars() was getting too big and too difficult
to follow. By splitting it into separate RDI and RSLI
handlers, we have smaller functions which are easy
to understand and only touch the pieces which they need
to touch.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
quite a few changes here, though they are
pretty obvious. In summary we're making sure
to detect which interrupt type we need to
handle before calling the underlying interrupt
handling procedure.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current support is known to be broken and
a later patch will come re-adding it using
dma engine API.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver doesn't need to know about its platform_device.
Everything the driver needs can be done through the
struct device pointer. In case we need to use the
OMAP-specific PM function pointers, those can make
sure to find the device's platform_device pointer
so they can find the struct omap_device through
pdev->archdata field.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These were reported in bugzilla long ago with a hack patch. Now we have a
proper patch for one we can do the rest.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=25102
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most of the time, the driver needs to check if the cts flow control
is enabled. But now, the driver checks the ASYNC_CTS_FLOW flag manually,
which is not a grace way. So add a new wraper function to make the code
tidy and clean.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this patch is in preparation to a few other changes
which will align on the prototype for function
pointers passed through pdata.
It also helps cleaning up the driver a little by
agregating checks for pdata in a single location.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
current code only works because struct uart_port
is the first member on the uart_omap_port structure.
If, for whatever reason, someone puts another
member as the first of the structure, that cast
won't work anymore. In order to be safe, let's use
a container_of() which, for now, gets optimized into
a cast anyway.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds note about migration to driver SCCNXP in the code
of driver SC26XX and in MIPS SNI board initialization with example.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver is a replacement for a SC26XX driver with a lot of
improvements and new features.
The main differences from the SC26XX driver:
- Removed dependency on MIPS. Driver can be used on any platform.
- Added support for SCC2681, SCC2691, SCC2692, SC28L91, SC28L92,
SC28L202, SCC68681 and SCC68692 ICs.
- Using devm_-related functions.
- Improved error handling of serial port, improved FIFO handling.
- Ability to load multiple instances of drivers.
To avoid the possibility of regression, driver SC26XX left in the
system to confirm the stability of the driver on platforms where
it is being used.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow parport_serial to handle the card the same PCI ids are blacklisted
in 8250_pci.c using the existing software blacklist mechanism.
The blacklist array is also renamed because it now covers this new use
case.
Since the two serial ports are auto-detected as XScale instead of 16550A
clones, we also add a quirk to 8250_pci.c to skip autodetection and set the
correct port type.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
[Fold in fixes for the uart_8250 change]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following errors and warnings:
ERROR: trailing whitespace
ERROR: return is not a function, parentheses are not required
WARNING: suspect code indent for conditional statements (32, 36)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the order of UART nodes is changed in the device tree, then tty dev
devices are attached to different serial ports causing the console to
be directed to a different physical serial port. The "serial" aliases
in the device tree should prevent this.
This patch ensures that the UART driver creates tty devices that
honour these aliases if a device tree is present.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure might have made sense many years ago, but at this
point it is only used in one specific driver, and referenced in
stale comments elsewhere. Rather than change the sunsu.c driver,
simply move the struct to be within the exclusive domain of that
driver, so it won't get inadvertently picked up and used by other
serial drivers going forward. The comments referencing the now
driver specific struct are updated accordingly.
Note that 8250.c has a struct that is similar in usage, with the
name serial8250_config; but is 100% independent and untouched here.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The addition of 8250-like entities continues to grow, while this
driver has a snapshot of a select few common 8250 UARTs. So it
has no need to grow with the new additions, since it calls out
its own (largely historic) static list which does not grow.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct serial_uart_config is hardly used at all, and the
use case like this one are somewhat needless. Remove the
trivial usage so that we can remove serial_uart_config.
Since the type field isn't really used at all, we also delete
the initialization and references of it here as well.
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These error paths are used more often now after deep changes to the
clock code and pinctrl is still new for imx. So help debugging and give
clues in the boot log.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want them split so that we can call them from setserial functionality
where we copy to/from user space and do the locking, but also from sysfs
where in future we'll want to came them within a sysfs context.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the clock configuration from imx_setup_ufcr(). This
isn't needed here and will cause garbage output if done.
To be be sure that we only touch the bits we want (TXTL and RXTL)
we have to mask out all other bits of the UFCR register. Add
one non-existing bit macro for this, too (bit 6, DCEDTE on i.MX6).
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Shawn Guo <shawn.guo@linaro.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Xinyu Chen <xinyu.chen@freescale.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The console feature's write routing is unsafe on SMP with
the startup/shutdown call.
There could be several consumers of the console
* the kernel printk
* the init process using /dev/kmsg to call printk to show log
* shell, which open /dev/console and write with sys_write()
The shell goes into the normal uart open/write routing,
but the other two go into the console operations.
The open routing calls imx serial startup, which will write USR1/2
register without any lock and critical with imx_console_write call.
Add a spin_lock for startup/shutdown/console_write routing.
This patch is a port from Freescale's Android kernel.
Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm free functions should not have to be explicitly used.
A semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
(
* devm_kfree(...);
|
* devm_free_irq(...);
|
* devm_iounmap(...);
|
* devm_release_region(...);
|
* devm_release_mem_region(...);
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested on a custom MPC5200B-board using some fancy industrial protocol.
Verified that MPC512x has identical bits, so should work there as well.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At commit 07d106d0, Linus pointed out that ENOIOCTLCMD should be
translated as ENOTTY to user mode.
For example:
fd = open("/dev/tty", O_RDWR);
ioctl(fd, -1, &argp);
then the errno should be ENOTTY but not EINVAL.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to explicitly call devm_kfree
in probe or remove functions.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gpiochip_remove function may fail to remove a gpio_chip
if any GPIOs are still requested. This patch informs the caller
of such a senario.
Sparse is warning because the function prototype has a
__must_check annotation.
Sparse warning:
drivers/tty/serial/max310x.c:1223:18: warning:
ignoring return value of ‘gpiochip_remove’,
declared with attribute warn_unused_result
[-Wunused-result]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper functions, so we can directly pass a struct
platfrom_device.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the driver's module init and exit functions can be replaced
with module_spi_driver as they do
only spi_register_driver and spi_unregister_driver in module's init and exit
paths.
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clk_prepare_enable and clk_disable_unprepare combine clk_prepare and
clk_enable, and clk_disable and clk_unprepare. The9 make the code more
concise, and ensure that clk_unprepare is called when clk_enable fails.
A simplified version of the semantic patch that introduces calls to these
functions is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
- clk_prepare(e);
- clk_enable(e);
+ clk_prepare_enable(e);
@@
expression e;
@@
- clk_disable(e);
- clk_unprepare(e);
+ clk_disable_unprepare(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pseries hvterm driver only registers a udbg backend (for xmon and
other low level debugging mechanisms) when hvc0 is recognized as the
firmware console at boot time, not if it's detected later on, for
example because the firmware is using a graphics card.
This can make debugging challenging especially under X11, and there's
really no good reason for that limitation, so let's hookup udbg
whenever hvc0 is detected instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
hvc_console has two methods to instanciate the consoles.
hvc_instanciate is meant to be called at early boot, while hvc_alloc is
called for more dynamically probed objects.
Currently, it only deals with adding kernel consoles in the former case,
which means for example that if a console only uses dynamic probing, it
will never be usable as a kernel console even when specifying
console=hvc0 explicitly, which could be considered annoying...
More specifically, on pseries, we only do the early instanciate for the
console currently used by the firmware, so if you have your firmware
configured to go to a video card, for example, you cannot get your
kernel console, oops messages, etc... on your serial port or hypervisor
console, which would be handy to deal with oopses.
This fixes it by checking if hvc_console.flags & CON_ENABLED is set when
registering a new dynamic console, and if not, redo the index check and
re-register the console if the index matches, allowing console=hvcN to
work.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
And if not, complain loudly. None in-kernel module should trigger
that, but let us find out for sure. On the other hand, all the
out-of-tree modules will hit that. Give them some time (maybe one
release) to catch up.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kdb <-> kgdb transitioning does not work properly with this UART
driver because the get character routine loops indefinitely as opposed
to returning NO_POLL_CHAR per the expectation of the KDB I/O driver
API.
The symptom is a kernel hang when trying to switch debug modes.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without checking if the auart supports the hardware flow control or not,
the old mxs_auart_set_mctrl() asserted the RTS pin blindly.
This will causes the auart receives wrong data in the following case:
The far-end has already started the write operation, and wait for
the auart asserts the RTS pin. Then the auart starts the read operation,
but mxs_auart_set_mctrl() may be called before we set the RTSCTS in the
mxs_auart_settermios(). So the RTS pin is asserted in a wrong situation,
and we get the wrong data in the end.
This bug has been catched when I connect the mx23(DTE) to the mx53(DCE).
This patch also replaces the AUART_CTRL2_RTS with AUART_CTRL2_RTSEN.
We should use the real the hardware flow control, not the software-controled
hardware flow control.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver is a replacement for a MAX3107 driver with a lot of
improvements and new features.
The main differences from the old version:
- Using the regmap.
- Using devm_XXX-related functions.
- The use of threaded IRQ with IRQF_ONESHOT flag allows the driver to
the hardware that supports only level IRQ.
- Improved error handling of serial port, improved FIFO handling,
improved hardware & software flow control.
- Advanced flags allows turn on RS-485 mode (Auto direction control).
- Ability to load multiple instances of drivers.
- Added support for MAX3108.
- GPIO support.
- Driver is quite ready for adding I2C support and support other ICs
with compatible registers set (MAX3109, MAX14830).
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OMAP hardware doesn't provide a phyisical DTR line, but
some configurations may need a DTR line which tracks whether
the device is open or not.
So allow a gpio to be configured as the DTR line.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported by coccinelle:
drivers/tty/serial/pch_uart.c:979:1-14: alloc with no test, possible model on line 994
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following compile breakage:
CC drivers/tty/serial/sc26xx.o
drivers/tty/serial/sc26xx.c: In function 'read_sc_port':
drivers/tty/serial/sc26xx.c💯 error: implicit declaration of function 'readb'
drivers/tty/serial/sc26xx.c: In function 'write_sc_port':
drivers/tty/serial/sc26xx.c:105: error: implicit declaration of function 'writeb'
drivers/tty/serial/sc26xx.c: In function 'sc26xx_probe':
drivers/tty/serial/sc26xx.c:652: error: implicit declaration of function 'ioremap_nocache'
drivers/tty/serial/sc26xx.c:652: warning: assignment makes pointer from integer without a cast
make[3]: *** [drivers/tty/serial/sc26xx.o] Error 1
make[2]: *** [drivers/tty/serial] Error 2
make[1]: *** [drivers/tty] Error 2
make: *** [drivers] Error 2
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We changed these from alloc_tty_driver() to tty_alloc_driver() so the
error handling needs to modified to check for IS_ERR() instead of NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Uplink (TX) network data will go through gsm_dlci_data_output_framed
there is a bug where if memory allocation fails, the skb which
has already been pulled off the list will be lost.
In addition TX skbs were being processed in LIFO order
Fixed the memory leak, and changed to FIFO order processing
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Kappel, LaurentX <laurentx.kappel@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Showjumping <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers are supposed to use the dev_* versions of the kfree_skb
interfaces. In a couple of cases we were called with IRQs
disabled as well which kfree_skb() does not expect.
Replaced kfree_skb calls w/ dev_kfree_skb and dev_kfree_skb_any
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Grooming <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm_data_kick was recently modified to allow messages on the
tx queue bound for DLCI0 to flow even during FCOFF conditions.
Unfortunately we introduced a bug discovered by code inspection
where subsequent list traversers can access freed memory if
the DLCI0 messages were not all at the head of the list.
Replaced singly linked tx list w/ a list_head and used
provided interfaces for traversing and deleting members.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Riding School <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were some locking holes in the management of the MUX's
message queue for 2 code paths:
1) gsmld_write_wakeup
2) receipt of CMD_FCON flow-control message
In both cases gsm_data_kick is called w/o locking so it can collide
with other other instances of gsm_data_kick (pulling messages tx_tail)
or potentially other instances of __gsm_data_queu (adding messages to tx_head)
Changed to take the tx_lock in these 2 cases
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Riding School <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The design of uplink flow control in the mux driver is
that for constipated channels data will backup into the
per-channel fifos, and any messages that make it to the
outbound message queue will still go out.
Code was added to also stop messages that were in the outbound
queue but this requires filtering through all the messages on the
queue for stopped dlcis and changes some of the mux logic unneccessarily.
The message fiiltering was removed to be in line w/ the original design
as the message filtering does not provide any solution.
Extra debug messages used during investigation were also removed.
Signed-off-by: samix.lebsir <samix.lebsir@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Dressage <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Correcting handling of FCon/FCoff in order to respect 27.010 spec
- Consider FCon/off will overide all dlci flow control except for
dlci0 as we must be able to send control frames.
- Dlci constipated handling according to FC, RTC and RTR values.
- Modifying gsm_dlci_data_kick and gsm_dlci_data_sweep according
to dlci constipated value
Signed-off-by: Frederic Berat <fredericx.berat@intel.com>
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm_dlci_data_kick will not call any output function if tx_bytes > THRESH_LO
furthermore it will call the output function only once if tx_bytes == 0
If the size of the IP writes are on the order of THRESH_LO
we can get into a situation where skbs accumulate on the outbound list
being starved for events to call the output function.
gsm_dlci_data_kick now calls the sweep function when tx_bytes==0
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Kappel, LaurentX <laurentx.kappel@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Hay and Water <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 3GPP27.010 5.8.1, it defined:
The TE multiplexer initiates the establishment of the multiplexer control channel by sending a SABM frame on DLCI 0 using the procedures of clause 5.4.1.
Once the multiplexer channel is established other DLCs may be established using the procedures of clause 5.4.1.
This patch implement 5.8.1 in MUX level, it make sure DLC0 is the first channel to be setup.
[or for those not familiar with the specification: it was possible to try
and open a data connection while the control channel was not yet fully
open, which is a spec violation and confuses some modems]
Signed-off-by: xiaojin <jin.xiao@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
[tweaked the order we check things and error code]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: The Horsebox <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the BUG_ON to WARN_ON and return in case of tty->read_buf==NULL. We want to track a
couple of long standing reports of this but at the same time we can avoid killing the box.
Signed-off-by: Stanislav Kozina <skozina@redhat.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Horses <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
444 means 0674 and we do not definitely want that. Use S_IRUGO which
is much more safer.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Rusty Russell <rusty@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has two outcomes:
* we give the TTY layer a tty_port
* we do not find the info structure every time open is called on that
tty
>From now on, we only increase the reference count in ->install (and
decrease in ->cleanup).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: linuxppc-dev@lists.ozlabs.org
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the code of hvcs_open a bit more readable by:
- moving all assignments out of if's
- redoing fail paths so that corresponding pieces are nearby
- we need only one of retval and rc
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has two outcomes:
* we give the TTY layer a tty_port
* we do not find the info structure every time open is called on that
tty
Since we take a reference to a port in ->install, we need also
->cleanup to drop that reference.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: linuxppc-dev@lists.ozlabs.org
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has two outcomes:
* we give the TTY layer a tty_port
* we do not find the info structure every time open is called on that
tty
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has two outcomes:
* we give the TTY layer a tty_port
* we do not find the info structure every time open is called on that
tty
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows us to provide the tty layer with information about
tty_port for each link.
We also provide a tty_port for the service port. For this one we allow
only ioctl, so this is pretty ugly.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So now for those drivers that can use neither tty_port_install nor
tty_port_register_driver but still have tty_port available before
tty_register_driver we use newly added tty_port_link_device.
The rest of the drivers that still do not provide tty_struct <->
tty_port link will have to be converted to implement
tty->ops->install.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is for those drivers which do not have dynamic device creation
(do not call tty_port_register_device) and do not want to implement
tty->ops->install (will not call tty_port_install). They still have to
provide the link somehow though.
And this newly added function is exactly to serve that purpose.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I forgot to document tty_port_register_device and tty_port_install
when they were added. Fix it now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This looks like it was a mistake not to create device nodes for these
drivers. Let us create them from now on.
It will be necessary to call tty_register_device some way, either by
tty_register_driver implicitly or to call tty_register_device proper.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: netdev@vger.kernel.org
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Cc: linux-cris-kernel@axis.com
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we have no way to assign tty->port while performing tty
installation. There are two ways to provide the link tty_struct =>
tty_port. Either by calling tty_port_install from tty->ops->install or
tty_port_register_device called instead of tty_register_device when
the device is being set up after connected.
In this patch we modify most of the drivers to do the latter. When the
drivers use tty_register_device and we have tty_port already, we
switch to tty_port_register_device. So we have the tty_struct =>
tty_port link for free for those.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the /dev/ node not to be available before we call
tty_register_device. Otherwise we might race with open and
tty_struct->port might not be available at that time.
This is not an issue now, but would be a problem after "TTY: use
tty_port_register_device" is applied.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows drivers like ttyprintk to avoid hacks to create an
unnumbered node in /dev. It used to set TTY_DRIVER_DYNAMIC_DEV in
flags and call device_create on its own. That is incorrect, because
TTY_DRIVER_DYNAMIC_DEV may be set only if tty_register_device is
called explicitly.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So now, that we have flags and know everything needed, keep a promise
and move all the tables and ports allocation from tty_register_driver
to tty_alloc_driver.
Not only that it makes sense, but we need this for
tty_port_link_device which needs tty_driver->ports but is to be called
before tty_register_driver.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the new driver allocation interface, as this is one of the
special call-sites. Here, we need TTY_DRIVER_DYNAMIC_ALLOC to not
allocate tty_driver->ports, cdevs and potentially other structures
because we reserve too many lines in pty. Instead, it provides the
tty_port<->tty_struct link in tty->ops->install already.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to allow drivers that use neither tty_port_install nor
tty_port_register_device to link a tty_port to a tty somehow. To
avoid a race with open, this has to be performed before
tty_register_device. But currently tty_driver->ports is allocated even
in tty_register_device because we do not know whether this is the PTY
driver. The PTY driver is special here due to an excessive count of
lines it declares to handle. We cannot handle tty_ports there this
way.
To circumvent this, we start passing tty_driver flags to
alloc_tty_driver already and we create tty_alloc_driver for this
purpose. There we can allocate tty_driver->ports and do all the magic
between tty_alloc_driver and tty_register_device. Later we will
introduce tty_port_link_device function for that purpose.
All drivers should eventually switch to this new tty driver allocation
interface.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For many cards, this saves some IO space because interrupt status port
has precedence over the rest of ports on the card. Hence it can be
mapped to a hole in I/O ports.
Here we add a kernel parameter which allows that if a user wants to.
But they need to explicitly enable it by a module parameter.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to link a port to a tty in install. And since dlci is
allocated even in open, we need to create gsmtty_install, allocate
dlci there and create also the link.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_struct->termios is no longer a pointer. This was changed recently
by "tty: move the termios object into the tty". But 68328serial was
not changed, so we now have a compilation error:
68328serial.c: In function 'change_speed':
68328serial.c:518:22: error: invalid type argument of '->' (have 'struct ktermios')
68328serial.c: In function 'rs_set_ldisc':
68328serial.c:620:31: error: invalid type argument of '->' (have 'struct ktermios')
68328serial.c: In function 'rs_set_termios':
68328serial.c:988:20: error: invalid type argument of '->' (have 'struct ktermios')
Fix that now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case alloc_tty_struct fails in pty_common_install, we pass NULL to
free_tty_struct. This is invalid as the function is not ready to cope
with that. And even if it was, it is not nice to do that anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This trivial patch adds a short description for SERIAL_CLPS711X Kconfig
entry, removes excess dependence on the ARM-platform (this is done
globally for the platform), allows the driver to be compiled by default
and removes unnecessary description about GRUB and LILO, because these
bootloaders do not supported this platform.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When PARMRK is set and large transfers of characters that will get
marked are being received, n_tty could drop data silently (i.e.
without reporting any error to the client). This is because
characters have the potential to take up to three bytes in the line
discipline (when they get marked with parity or framing errors), but
the amount of free space reported to tty_buffer flush_to_ldisc (via
tty->receive_room) is based on the pre-marked data size.
With this patch, the n_tty layer will no longer assume that each byte
will only take up one byte in the line discipline. Instead, it will
make an overly conservative estimate that each byte will take up
three bytes in the line discipline when PARMRK is set.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix possible panic caused by unlocked access to tty->read_cnt in
while-loop condition in n_tty_read().
Signed-off-by: Stanislav Kozina <skozina@redhat.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The termios and other changes mean the other protections needed on the driver
tty arrays should be adequate. Turn it all back on.
This contains pieces folded in from the fixes made to the original patches
| From: Geert Uytterhoeven <geert@linux-m68k.org> (fix m68k)
| From: Paul Gortmaker <paul.gortmaker@windriver.com> (fix cris)
| From: Jiri Kosina <jkosina@suze.cz> (lockdep)
| From: Eric Dumazet <eric.dumazet@gmail.com> (lockdep)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We sometimes pass NULL pointers to free_tty_struct(). One example where
it can happen is in the error handling code in pty_common_install().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're trying to save the termios state and we need to allocate a buffer
to do it. Smatch complains that the buffer is leaked at the end of the
function.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This handles the merge issue in:
arch/um/drivers/line.c
arch/um/drivers/line.h
And resolves the duplicate patches that were in both trees do to the
tty-next branch not getting merged into 3.6-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This prepares *of_device_id.data becoming const. Without this change the
following warning would occur:
drivers/tty/serial/imx.c: In function 'serial_imx_probe_dt':
drivers/tty/serial/imx.c:1430:17: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
A recent commit:
commit d6fa5a4e7a
Author: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
serial: sh-sci: prepare for conversion to the shdma base library
is not sufficient to update the sh-sci driver to the new shdma driver
layout. This caused compilation breakage, when CONFIG_SERIAL_SH_SCI_DMA
is enabled. This patch trivially fixes the problem by updating the DMA
descriptor manipulation code.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
from interrupts for /dev/random and /dev/urandom. The goal is to
addresses weaknesses discussed in the paper "Mining your Ps and Qs:
Detection of Widespread Weak Keys in Network Devices", by Nadia
Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman, which will
be published in the Proceedings of the 21st Usenix Security Symposium,
August 2012. (See https://factorable.net for more information and an
extended version of the paper.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u7KM
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random subsystem patches from Ted Ts'o:
"This patch series contains a major revamp of how we collect entropy
from interrupts for /dev/random and /dev/urandom.
The goal is to addresses weaknesses discussed in the paper "Mining
your Ps and Qs: Detection of Widespread Weak Keys in Network Devices",
by Nadia Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman,
which will be published in the Proceedings of the 21st Usenix Security
Symposium, August 2012. (See https://factorable.net for more
information and an extended version of the paper.)"
Fix up trivial conflicts due to nearby changes in
drivers/{mfd/ab3100-core.c, usb/gadget/omap_udc.c}
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (33 commits)
random: mix in architectural randomness in extract_buf()
dmi: Feed DMI table to /dev/random driver
random: Add comment to random_initialize()
random: final removal of IRQF_SAMPLE_RANDOM
um: remove IRQF_SAMPLE_RANDOM which is now a no-op
sparc/ldc: remove IRQF_SAMPLE_RANDOM which is now a no-op
[ARM] pxa: remove IRQF_SAMPLE_RANDOM which is now a no-op
board-palmz71: remove IRQF_SAMPLE_RANDOM which is now a no-op
isp1301_omap: remove IRQF_SAMPLE_RANDOM which is now a no-op
pxa25x_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
omap_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
goku_udc: remove IRQF_SAMPLE_RANDOM which was commented out
uartlite: remove IRQF_SAMPLE_RANDOM which is now a no-op
drivers: hv: remove IRQF_SAMPLE_RANDOM which is now a no-op
xen-blkfront: remove IRQF_SAMPLE_RANDOM which is now a no-op
n2_crypto: remove IRQF_SAMPLE_RANDOM which is now a no-op
pda_power: remove IRQF_SAMPLE_RANDOM which is now a no-op
i2c-pmcmsp: remove IRQF_SAMPLE_RANDOM which is now a no-op
input/serio/hp_sdc.c: remove IRQF_SAMPLE_RANDOM which is now a no-op
mfd: remove IRQF_SAMPLE_RANDOM which is now a no-op
...
Pull ARM updates from Russell King:
"First ARM push of this merge window, post me coming back from holiday.
This is what has been in linux-next for the last few weeks. Not much
to say which isn't described by the commit summaries."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (32 commits)
ARM: 7463/1: topology: Update cpu_power according to DT information
ARM: 7462/1: topology: factorize the update of sibling masks
ARM: 7461/1: topology: Add arch_scale_freq_power function
ARM: 7456/1: ptrace: provide separate functions for tracing syscall {entry,exit}
ARM: 7455/1: audit: move syscall auditing until after ptrace SIGTRAP handling
ARM: 7454/1: entry: don't bother with syscall tracing on ret_from_fork path
ARM: 7453/1: audit: only allow syscall auditing for pure EABI userspace
ARM: 7452/1: delay: allow timer-based delay implementation to be selected
ARM: 7451/1: arch timer: implement read_current_timer and get_cycles
ARM: 7450/1: dcache: select DCACHE_WORD_ACCESS for little-endian ARMv6+ CPUs
ARM: 7449/1: use generic strnlen_user and strncpy_from_user functions
ARM: 7448/1: perf: remove arm_perf_pmu_ids global enumeration
ARM: 7447/1: rwlocks: remove unused branch labels from trylock routines
ARM: 7446/1: spinlock: use ticket algorithm for ARMv6+ locking implementation
ARM: 7445/1: mm: update CONTEXTIDR register to contain PID of current process
ARM: 7444/1: kernel: add arch-timer C3STOP feature
ARM: 7460/1: remove asm/locks.h
ARM: 7439/1: head.S: simplify initial page table mapping
ARM: 7437/1: zImage: Allow DTB command line concatenation with ATAG_CMDLINE
ARM: 7436/1: Do not map the vectors page as write-through on UP systems
...
Here's the "tiny" set of patches for 3.6-rc1 for the tty layer and
serial drivers. They were cherry-picked from the tty-next branch of the
tty git tree, as they are small and "obvious" fixes. The larger
changes, as mentioned before, will be saved for the 3.7-rc1 merge
window.
All of these changes have been in the linux-next releases for quite a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAS5OkACgkQMUfUDdst+ykYLgCfdCz1v64yvk21r8un9fa3JXYW
dIIAoNcIeLHsUOcmMSp0JN2oZkBNZOb7
=y7gx
-----END PGP SIGNATURE-----
Merge tag 'tty-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/Serial patches from Greg Kroah-Hartman:
"Here's the "tiny" set of patches for 3.6-rc1 for the tty layer and
serial drivers. They were cherry-picked from the tty-next branch of
the tty git tree, as they are small and "obvious" fixes. The larger
changes, as mentioned before, will be saved for the 3.7-rc1 merge
window.
All of these changes have been in the linux-next releases for quite a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
pch_uart: Fix parity setting issue
pch_uart: Fix rx error interrupt setting issue
pch_uart: Fix missing break for 16 byte fifo
tty ldisc: Close/Reopen race prevention should check the proper flag
pch_uart: Add eg20t_port lock field, avoid recursive spinlocks
vt: fix race in vt_waitactive()
serial/of-serial: Add LPC3220 standard UART compatible string
serial/8250: Add LPC3220 standard UART type
serial_core: Update buffer overrun statistics.
serial: samsung: Fixed wrong comparison for baudclk_rate
Ian Abbott found that the tty layer would explode with the right set of
parallel open and close operations. This is because we race in the
handling of tty->drivers->termios[].
Correct this by
Making tty_ldisc_release behave like nromal code (takes the lock,
does stuff, drops the lock)
Drop the tty lock earlier in tty_ldisc_release
Taking the tty mutex around the driver->termios update in all cases
Adding a WARN_ON to catch future screwups.
I also forgot to clean up the pty resources properly. With a pty pair we
need to pull both halves out of the tables.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parity Setting value is reverse.
E.G. In case of setting ODD parity, EVEN value is set.
This patch inverts "if" condition.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rx Error interrupt(E.G. parity error) is not enabled.
So, when parity error occurs, error interrupt is not occurred.
As a result, the received data is not dropped.
This patch adds enable/disable rx error interrupt code.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise we fall back to the wrong value.
Reported-by: <dcb314@hotmail.com>
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44091
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit acfa747b introduced the TTY_HUPPING flag to distinguish
closed TTY from currently closing ones. The test in tty_set_ldisc
still remained pointing at the old flag. This causes pppd to
sometimes lapse into uninterruptible sleep when killed and
restarted.
Signed-off-by: Shachar Shemesh <shachar@liveu.tv>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pch_uart_interrupt() takes priv->port.lock which leads to two recursive
spinlock calls if low_latency==1 or CONFIG_PREEMPT_RT_FULL=y (one
otherwise):
pch_uart_interrupt
spin_lock_irqsave(priv->port.lock, flags)
case PCH_UART_IID_RDR_TO (data ready)
handle_rx_to
push_rx
tty_port_tty_get
spin_lock_irqsave(&port->lock, flags) <--- already hold this lock
...
tty_flip_buffer_push
...
flush_to_ldisc
spin_lock_irqsave(&tty->buf.lock)
spin_lock_irqsave(&tty->buf.lock)
disc->ops->receive_buf(tty, char_buf)
n_tty_receive_buf
tty->ops->flush_chars()
uart_flush_chars
uart_start
spin_lock_irqsave(&port->lock) <--- already hold this lock
Avoid this by using a dedicated lock to protect the eg20t_port structure
and IO access to its membase. This is more consistent with the 8250
driver. Ensure priv->lock is always take prior to priv->port.lock when
taken at the same time.
V2: Remove inadvertent whitespace change.
V3: Account for oops_in_progress for the private lock in
pch_console_write().
Note: Like the 8250 driver, if a printk is introduced anywhere inside
the pch_console_write() critical section, the kernel will hang
on a recursive spinlock on the private lock. The oops case is
handled by using a trylock in the oops_in_progress case.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Feng Tang <feng.tang@intel.com>
CC: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_restore_console() is called from the suspend/resume path, and this
calls vt_move_to_console(), which calls vt_waitactive().
There's a race in this path which causes the process which requests the
suspend to sleep indefinitely waiting for an event which already
happened:
P1 P2
vt_move_to_console()
set_console()
schedule_console_callback()
vt_waitactive()
check n == fg_console +1
console_callback()
switch_screen()
vt_event_post() // no waiters
vt_event_wait() // forever
Fix the race by ensuring we're registered for the event before we check
if it's already completed.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a "compatible" string for the new 8250 UART type PORT_LPC3220.
This is necessary for initializing LPC32xx UARTs via DT.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPC32xx has "Standard" UARTs that are actually 16550A compatible but have
bigger FIFOs. Since the already supported 16X50 line still doesn't match here,
we agreed on adding a new type.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, serial drivers don't report buffer overruns. When a buffer overrun
occurs, tty_insert_flip_char returns 0, and no attempt is made to insert that
same character again (i.e. it is lost). This patch reports buffer overruns via
the buf_overrun field in the port's icount structure.
Signed-off-by: Corbin Atkinson <corbin.atkinson@xxxxxx>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
port->baudclk_rate should be compared to the rate of port->baudclk,
because port->baudclk_rate was assigned as the rate of port->baudclk previously.
So to check that the current baudclk rate is same as previous rate,
the target of comparison sholud be the rate of port->baudclk.
Signed-off-by: Jun-Ho, Yoon <junho78.yoon@samsung.com>
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull slave-dmaengine update from Vinod Koul:
"This time we have a new dmaengine driver from the tegra folks. Also
we have Guennadi's cleanup of sh drivers which incudes a library for
sh drivers. And the usual odd fixes in bunch of drivers and some nice
cleanup of dw_dmac from Andy."
Fix up conflicts in drivers/mmc/host/sh_mmcif.c
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: Cleanup logging messages
mmc: sh_mmcif: switch to the new DMA channel allocation and configuration
dma: sh: provide a migration path for slave drivers to stop using .private
dma: sh: use an integer slave ID to improve API compatibility
dmaengine: shdma: prepare to stop using struct dma_chan::private
sh: remove unused DMA device pointer from SIU platform data
ASoC: siu: don't use DMA device for channel filtering
dmaengine: shdma: (cosmetic) simplify a static function
dmaengine: at_hdmac: add a few const qualifiers
dw_dmac: use 'u32' for LLI structure members, not dma_addr_t
dw_dmac: mark dwc_dump_lli inline
dma: mxs-dma: Export missing symbols from mxs-dma.c
dma: shdma: convert to the shdma base library
ASoC: fsi: prepare for conversion to the shdma base library
usb: renesas_usbhs: prepare for conversion to the shdma base library
ASoC: siu: prepare for conversion to the shdma base library
serial: sh-sci: prepare for conversion to the shdma base library
mmc: sh_mobile_sdhi: prepare for conversion to the shdma base library
mmc: sh_mmcif: remove unneeded struct sh_mmcif_dma, prepare to shdma conversion
dma: shdma: prepare for conversion to the shdma base library
...
* Performance improvement to lower the amount of traps the hypervisor
has to do 32-bit guests. Mainly for setting PTE entries and updating
TLS descriptors.
* MCE polling driver to collect hypervisor MCE buffer and present them to
/dev/mcelog.
* Physical CPU online/offline support. When an privileged guest is booted
it is present with virtual CPUs, which might have an 1:1 to physical
CPUs but usually don't. This provides mechanism to offline/online physical
CPUs.
Bug-fixes for:
* Coverity found fixes in the console and ACPI processor driver.
* PVonHVM kexec fixes along with some cleanups.
* Pages that fall within E820 gaps and non-RAM regions (and had been
released to hypervisor) would be populated back, but potentially in
non-RAM regions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQDWcvAAoJEFjIrFwIi8fJ6GAH/iFIkOC5wseD8qZ9nV4VI46t
0GYvBFC4F91NvC7CNfoAySr84v+ZORIZzMcdyDF8H/tLO9MaOY/Mwn0S5ZSqmYMi
rhskvK3InBaVkYtceOHugNGM7mB0c3STIm7OsjW6gbVzohmTN25rbQR+X5iWAtVA
cTUtDyH3AU15mwuVT3U+VC4IulHpnNJz4pHoq3Sn61/UK1LYmhLXYd5fveA0D0B8
lRZTAvNMsYDJDDmkWNrs8RczKkQ86DTSjfGawm0YG+Gf94GgD5yMHWbiHh2Gy93e
u7sHK0RrKbP5BY/MV6vVJxkoV5NoWgCc0tcjBcYwdyvwzxDS75UhV6uoVHC3Ao8=
=drt2
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen update from Konrad Rzeszutek Wilk:
"Features:
* Performance improvement to lower the amount of traps the hypervisor
has to do 32-bit guests. Mainly for setting PTE entries and
updating TLS descriptors.
* MCE polling driver to collect hypervisor MCE buffer and present
them to /dev/mcelog.
* Physical CPU online/offline support. When an privileged guest is
booted it is present with virtual CPUs, which might have an 1:1 to
physical CPUs but usually don't. This provides mechanism to
offline/online physical CPUs.
Bug-fixes for:
* Coverity found fixes in the console and ACPI processor driver.
* PVonHVM kexec fixes along with some cleanups.
* Pages that fall within E820 gaps and non-RAM regions (and had been
released to hypervisor) would be populated back, but potentially in
non-RAM regions."
* tag 'stable/for-linus-3.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: populate correct number of pages when across mem boundary (v2)
xen PVonHVM: move shared_info to MMIO before kexec
xen: simplify init_hvm_pv_info
xen: remove cast from HYPERVISOR_shared_info assignment
xen: enable platform-pci only in a Xen guest
xen/pv-on-hvm kexec: shutdown watches from old kernel
xen/x86: avoid updating TLS descriptors if they haven't changed
xen/x86: add desc_equal() to compare GDT descriptors
xen/mm: zero PTEs for non-present MFNs in the initial page table
xen/mm: do direct hypercall in xen_set_pte() if batching is unavailable
xen/hvc: Fix up checks when the info is allocated.
xen/acpi: Fix potential memory leak.
xen/mce: add .poll method for mcelog device driver
xen/mce: schedule a workqueue to avoid sleep in atomic context
xen/pcpu: Xen physical cpus online/offline sys interface
xen/mce: Register native mce handler as vMCE bounce back point
x86, MCE, AMD: Adjust initcall sequence for xen
xen/mce: Add mcelog support for Xen platform
The I.MX platform is getting converted to use sparse IRQs. We are doing
this for all platforms over time, because this is one of the
requirements for building a multiplatform kernel, and generally a good
idea.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Y2Sm
-----END PGP SIGNATURE-----
Merge tag 'irq' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc sparse IRQ conversion from Arnd Bergmann:
"The I.MX platform is getting converted to use sparse IRQs. We are
doing this for all platforms over time, because this is one of the
requirements for building a multiplatform kernel, and generally a good
idea."
* tag 'irq' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: select USE_OF
ARM: imx: Fix build error due to missing irqs.h include
ARM: imx: enable SPARSE_IRQ for imx platform
ARM: fiq: change FIQ_START to a variable
tty: serial: imx: remove the use of MXC_INTERNAL_IRQS
ARM: imx: remove unneeded mach/irq.h inclusion
i2c: imx: remove unneeded mach/irqs.h inclusion
ARM: imx: add a legacy irqdomain for mx31ads
ARM: imx: add a legacy irqdomain for 3ds_debugboard
ARM: imx: pass gpio than irq number into mxc_expio_init
ARM: imx: leave irq_base of wm8350_platform_data uninitialized
dma: ipu: remove the use of ipu_platform_data
ARM: imx: move irq_domain_add_legacy call into avic driver
ARM: imx: move irq_domain_add_legacy call into tzic driver
gpio/mxc: move irq_domain_add_legacy call into gpio driver
ARM: imx: eliminate macro IRQ_GPIOx()
ARM: imx: eliminate macro IOMUX_TO_IRQ()
ARM: imx: eliminate macro IMX_GPIO_TO_IRQ()
This branch contains two kinds of updates: Some platforms in the process
of getting converted to device tree based booting, and the platform
specific patches necessary for that are included here. Other platforms
are already converted, so we just need to update the actual device
tree source files and the binding documents to add support for new board
and new drivers.
In the future we will probably separate those into two branches, and
in the long run, the plan is to move the device tree source files out
of the kernel repository, but that has to wait until we have completed
a much larger portion of the binding documents.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=K3WL
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc device tree description updates from Arnd Bergmann:
"This branch contains two kinds of updates: Some platforms in the
process of getting converted to device tree based booting, and the
platform specific patches necessary for that are included here.
Other platforms are already converted, so we just need to update the
actual device tree source files and the binding documents to add
support for new board and new drivers.
In the future we will probably separate those into two branches, and
in the long run, the plan is to move the device tree source files out
of the kernel repository, but that has to wait until we have completed
a much larger portion of the binding documents."
Fix up trivial conflicts in arch/arm/mach-imx/clk-imx6q.c due to newly
added clkdev registers next to a few removed unnecessary ones.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: LPC32xx: Add PWM to base dts file
ARM: EXYNOS: mark the DMA channel binding for SPI as preliminary
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS5 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOS5
ARM: EXYNOS: Add spi clock support for EXYNOS5
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS4 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOX4
ARM: EXYNOS: Fix the incorrect hierarchy of spi controller bus clock
ARM: ux500: Remove PMU platform registration when booting with DT
ARM: ux500: Remove temporary snowball_of_platform_devs enablement structure
ARM: ux500: Ensure vendor specific properties have the vendor's identifier
pinctrl: pinctrl-nomadik: Append sleepmode property with vendor specific prefixes
ARM: ux500: Move rtc-pl031 registration to Device Tree when enabled
ARM: ux500: Enable the AB8500 RTC for all DT:ed DB8500 based devices
ARM: ux500: Correctly reference IRQs supplied by the AB8500 from Device Tree
ARM: ux500: Apply ab8500-debug node do the db8500 DT structure
ARM: ux500: Add a ab8500-usb Device Tree node for db8500 based devices
ARM: ux500: Add db8500 Device Tree node for misc/ab8500-pwm
ARM: ux500: Add db8500 Device Tree node for ab8500-sysctrl
ARM: ux500: Enable LED heartbeat functionality on Snowbal via DT
...
With the changes in the random tree, IRQF_SAMPLE_RANDOM is now a
no-op; interrupt randomness is now collected unconditionally in a very
low-overhead fashion; see commit 775f4b297b. The IRQF_SAMPLE_RANDOM
flag was scheduled to be removed in 2009 on the
feature-removal-schedule, so this patch is preparation for the final
removal of this flag.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Parity Setting value is reverse.
E.G. In case of setting ODD parity, EVEN value is set.
This patch inverts "if" condition.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rx Error interrupt(E.G. parity error) is not enabled.
So, when parity error occurs, error interrupt is not occurred.
As a result, the received data is not dropped.
This patch adds enable/disable rx error interrupt code.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise we fall back to the wrong value.
Reported-by: <dcb314@hotmail.com>
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44091
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The loopback test mode is not implemented in all
NS16550 compatible UARTs. The 8250 driver uses the
UPF_SKIP_TEST flag to indicate this, however it is
not possible to set this flag via device-tree.
Add a new 'no-loopback-test' property, and modify
the of_serial driver to set the UPF_SKIP_TEST flag
if the property is present.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we don't have tty->termios tied to drivers->tty we can untangle
the logic here. In addition we can push the removal logic out of the
destructor path.
At that point we can think about sorting out tty_port and console and all
the other ugly hangovers.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We touch the LED from both keyboard callback and direct paths. In
one case we've got the lock held way up the call chain and in the
other we haven't. This leads to complete insanity so fix it by giving
the LED bits their own lock.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the differences between the original 8250 patch, the revised 8250 patch
and the independant clean up of the octeon driver (to use platform devices properly yay!)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes up the problem Stephen Rothwell reported when trying to merge -next
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@cab.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will let us sort out a whole pile of tty related races. The
alternative would be to keep points and refcount the termios objects.
However
1. They are tiny anyway
2. Many devices don't use the stored copies
3. We can remove a pty special case
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I sent GregKH this after the pre-requisites. He dropped the pre-requesites
for good reason and unfortunately then applied this patch. Without this
reverted you get random kernel memory corruption which will make bisecting
anything between it and the properly applied patches a complete sod.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit acfa747b introduced the TTY_HUPPING flag to distinguish
closed TTY from currently closing ones. The test in tty_set_ldisc
still remained pointing at the old flag. This causes pppd to
sometimes lapse into uninterruptible sleep when killed and
restarted.
Signed-off-by: Shachar Shemesh <shachar@liveu.tv>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Information and a different patch provided by <donald@asix.com.tw>. We do
it a little differently to keep the modularity and to avoid playing with
RLSI.
We add a new uart bug for the parity flaw and set it in the pci matches.
If parity check is enabled then we drop the FIFO trigger to 1 as per the
Asix reference code.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now we are using the uart_8250_port this is trivial
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old interface just copies bits over and calls the newer one.
In addition we can now pass more information.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem here is that we called mutex_unlock(&devpts_mutex) on the
error path when we weren't holding the lock.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
udbg_init_debug_opal() should be udbg_init_debug_opal_raw() as
the caller in arch/powerpc/kernel/udbg.c expects
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are three call sites for this function, and all three
are called within a keyboard handler.
kbd_event_lock is already held within keyboard handlers,
so attempting to lock it in vt_get_leds causes deadlock.
Signed-off-by: Christopher Brannon <chris@the-brannons.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The termios and other changes mean the other protections needed on the driver
tty arrays should be adequate. Turn it all back on.
This contains pieces folded in from the fixes made to the original patches
| From: Geert Uytterhoeven <geert@linux-m68k.org> (fix m68k)
| From: Paul Gortmaker <paul.gortmaker@windriver.com> (fix cris)
| From: Jiri Kosina <jkosina@suze.cz> (lockdep)
| From: Eric Dumazet <eric.dumazet@gmail.com> (lockdep)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From Shawn Guo <shawn.guo@linaro.org>, this makes it possible to use
sparse irqs with mach-imx.
* 'imx/sparse-irq' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: enable SPARSE_IRQ for imx platform
ARM: fiq: change FIQ_START to a variable
tty: serial: imx: remove the use of MXC_INTERNAL_IRQS
ARM: imx: remove unneeded mach/irq.h inclusion
i2c: imx: remove unneeded mach/irqs.h inclusion
ARM: imx: add a legacy irqdomain for mx31ads
ARM: imx: add a legacy irqdomain for 3ds_debugboard
ARM: imx: pass gpio than irq number into mxc_expio_init
ARM: imx: leave irq_base of wm8350_platform_data uninitialized
dma: ipu: remove the use of ipu_platform_data
ARM: imx: move irq_domain_add_legacy call into avic driver
ARM: imx: move irq_domain_add_legacy call into tzic driver
gpio/mxc: move irq_domain_add_legacy call into gpio driver
ARM: imx: eliminate macro IRQ_GPIOx()
ARM: imx: eliminate macro IOMUX_TO_IRQ()
ARM: imx: eliminate macro IMX_GPIO_TO_IRQ()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As the part of the effort to enable SPARE_IRQ for imx platform,
the macro MXC_INTERNAL_IRQS will be removed. The imx serial driver
has a references to it for a decision on flags of request_irq call
based on rtsirq is beyond MXC_INTERNAL_IRQS. However the searching
on imx platform code tells that rtsirq will never be beyond
MXC_INTERNAL_IRQS. That said, the check, consequently the reference
to MXC_INTERNAL_IRQS are not needed, so remove them.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
This was identified by Vincent Pillet with a high speed interface that uses
low latency mode. In the low latency case we have a tiny race but it can
be hit.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to pick up the serial port and tty changes in Linus's tree to allow
everyone to sync up.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pch_uart_interrupt() takes priv->port.lock which leads to two recursive
spinlock calls if low_latency==1 or CONFIG_PREEMPT_RT_FULL=y (one
otherwise):
pch_uart_interrupt
spin_lock_irqsave(priv->port.lock, flags)
case PCH_UART_IID_RDR_TO (data ready)
handle_rx_to
push_rx
tty_port_tty_get
spin_lock_irqsave(&port->lock, flags) <--- already hold this lock
...
tty_flip_buffer_push
...
flush_to_ldisc
spin_lock_irqsave(&tty->buf.lock)
spin_lock_irqsave(&tty->buf.lock)
disc->ops->receive_buf(tty, char_buf)
n_tty_receive_buf
tty->ops->flush_chars()
uart_flush_chars
uart_start
spin_lock_irqsave(&port->lock) <--- already hold this lock
Avoid this by using a dedicated lock to protect the eg20t_port structure
and IO access to its membase. This is more consistent with the 8250
driver. Ensure priv->lock is always take prior to priv->port.lock when
taken at the same time.
V2: Remove inadvertent whitespace change.
V3: Account for oops_in_progress for the private lock in
pch_console_write().
Note: Like the 8250 driver, if a printk is introduced anywhere inside
the pch_console_write() critical section, the kernel will hang
on a recursive spinlock on the private lock. The oops case is
handled by using a trylock in the oops_in_progress case.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Feng Tang <feng.tang@intel.com>
CC: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are 3 patches resolving a boot regression (the mop500 fix), a build
warning fix, and a kernel-doc fix. All tiny, but should go into the
final 3.5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNosACgkQMUfUDdst+ykedgCeLhpFrq5dI19tbhEmCroFs4sx
f+4An29dz2bGkjeViDNkmaBC7msPzLNc
=EBge
-----END PGP SIGNATURE-----
Merge tag 'tty-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg Kroah-Hartman:
"Here are 3 patches resolving a boot regression (the mop500 fix), a
build warning fix, and a kernel-doc fix. All tiny, but should go into
the final 3.5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial/amba-pl011: move custom pin control to driver
serial: fix serial_txx9.c build warning/typo
serial: fix kernel-doc warnings in 8250.c
The PL011 driver has a number of symbols referring to "pl01x"
(probably once shared with the pl010 driver) and some even named
"pl010" (probably a pure copy-paste artifact). Lets name all
local static functions with the prefix pl011_* for clarity.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- When booting as PVHVM we would try to use PV console - but would not validate
the parameters causing us to crash during restore b/c we re-use the wrong event
channel.
- When booting on machines with SR-IOV PCI bridge we didn't check for the bridge
and tried to use it.
- Under AMD machines would advertise the APERFMPERF resulting in needless amount
of MSRs from the guest.
- A global value (xen_released_pages) was not subtracted at bootup when pages
were added back in. This resulted in the balloon worker having the wrong
account of how many pages were truly released.
- Fix dead-lock when xen-blkfront is run in the same domain as xen-blkback.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJP2kcmAAoJEFjIrFwIi8fJXLcH/0a2m6KMcyjc4WaCHspAEFDL
9B055QUFDEOlH55wE2QeED/8D+0HUbTYnQBycH126XLKzLfRv1fsrKFKDSA/SWW2
Mh8N316UrY5Wc3KMdxXdCXJCDqDs7VhARTv6JdlUqUlH9oLRYE6CMRO8MujT0iwd
r+uEnNuW0udMFt8x9SnJW7pEaq7u2N5koEGdWEzZhfoumDaCRxm5OKAKXZ0DZlEZ
/BPjTW/N+Pf4u+bJZY+wQq41y4zGMqu7TDo/hOpuGZxeqtVnCE9trBbuGLnp4K+W
n4TfZZs9Y1kovSMj6qTeB0aP0F77tqHyXPb1oPKxm2kWfqT2dFtIRpuLtXYSC+o=
=cQl2
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.5-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull five Xen bug-fixes from Konrad Rzeszutek Wilk:
- When booting as PVHVM we would try to use PV console - but would not validate
the parameters causing us to crash during restore b/c we re-use the wrong event
channel.
- When booting on machines with SR-IOV PCI bridge we didn't check for the bridge
and tried to use it.
- Under AMD machines would advertise the APERFMPERF resulting in needless amount
of MSRs from the guest.
- A global value (xen_released_pages) was not subtracted at bootup when pages
were added back in. This resulted in the balloon worker having the wrong
account of how many pages were truly released.
- Fix dead-lock when xen-blkfront is run in the same domain as xen-blkback.
* tag 'stable/for-linus-3.5-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: mark local pages as FOREIGN in the m2p_override
xen/setup: filter APERFMPERF cpuid feature out
xen/balloon: Subtract from xen_released_pages the count that is populated.
xen/pci: Check for PCI bridge before using it.
xen/events: Add WARN_ON when quick lookup found invalid type.
xen/hvc: Check HVM_PARAM_CONSOLE_[EVTCHN|PFN] for correctness.
xen/hvc: Fix error cases around HVM_PARAM_CONSOLE_PFN
xen/hvc: Collapse error logic.
v3:
Remove empty line
v2:
Move local_irq_save() after clk_prepare_enable()
v1:
At UP mode, when cpu want to print message in kernel, it will invoke
peempt_disable and disable irq. So it is safe for UP mode.
For SMP mode, it is not safe to protect the HW reigsters.
one CPU will run a program which will invoke printf.
another CPU will run a program in kernel that invoke printk.
So when second CPU is trying to printk, it will do
1. save ier register
2. enable uue bit of ier register
3. push buffer to uart fifo
4 .restore ier register
when first CPU want to printf, and it happens between 1 and 4, it will
enable thre bit of ier, and waiting for transmit intterupt. while step 4
will make the ier lost thre bit.
add spin lock here to protect the ier register for console write.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_restore_console() is called from the suspend/resume path, and this
calls vt_move_to_console(), which calls vt_waitactive().
There's a race in this path which causes the process which requests the
suspend to sleep indefinitely waiting for an event which already
happened:
P1 P2
vt_move_to_console()
set_console()
schedule_console_callback()
vt_waitactive()
check n == fg_console +1
console_callback()
switch_screen()
vt_event_post() // no waiters
vt_event_wait() // forever
Fix the race by ensuring we're registered for the event before we check
if it's already completed.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will automatically assign tty_port to tty_driver's port array for
later recall in tty_init_dev. This is intended to be called instead of
tty_register_device.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It will hold tty_port structures for all drivers which do not want to
define tty->ops->install hook.
We ignore PTY here because it wants 1 million lines and it installs
tty_port in ->install anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, some failures are handled in if's false branches, some at
the end of tty_register_driver via goto-labels. Let us handle the
failures at the end of the functions to have the failure handling at
a single place. The only thing needed is to label the lines properly
and jump there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to initialize the console only on the first open. This is
usually what is done in the ->install hook. vt used to do this in
->open. Now we move it to ->install and use newly added helper for
install: tty_port_install. It ensures tty->port to be set properly.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will be used in tty_ops->install to set tty->port (and to call
tty_standard_install).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is identical to tty_schedule_flip. So let us use that instead.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has *no* function in the PTY driver yet. However as the tty
buffers will move to the tty_port structure, we will need tty_port for
all TTYs in the system, PTY inclusive.
For PTYs this is ensured by allocating 2 tty_port's in pty_install,
i.e. where the tty->link is allocated. Both tty_port's are properly
assigned to each end of the tty.
Freeing is done at the same place where tty is freed, i.e. in
tty->ops->cleanup.
This means BTW that tty_port does not outlive TTY in PTY. This might
be a subject to change in the future if we see some problems.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are currently two instances of code which handles PTY install.
One for the legacy BSD PTY's, one for unix98's PTY's. Both of them are
very similar and differ only in termios allocation and handling.
Since we will need to allocate a tty_port at that place, this would
require editing two places with the same pattern. Instead, let us move
the implementation to one common place and call it from both places.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, there are two as a left-over from previous patches.
Although we really need to provide an empty handler, we do not need
two. So remove one of them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver supports a maximum number of ports configurable at compile
time. Make sure the probe() method fails when registering a port that
exceeds the maximum instead of returning success without registering the
port.
This fixes a crash at system suspend time, when the driver tried to
suspend a non-registered port using the UART core.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When probing fails, the driver must not try to cleanup resources that
have not been initialized. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The driver supports a maximum number of ports configurable at compile
time. Make sure the probe() method fails when registering a port that
exceeds the maximum instead of returning success without registering the
port.
This fixes a crash at system suspend time, when the driver tried to
suspend a non-registered port using the UART core.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When probing fails, the driver must not try to cleanup resources that
have not been initialized. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cy_pci_probe and cy_detect_isa reference cy_card[card_no] many times.
It makes the code hard to read. Let us add a local variable holding a
pointer to the card indexed by card_no and use that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pbn_exsys_4055 is the same thing as pbn_b2_4_115200 so replace it with
the standard pattern.
Signed-off-by: Shawn Bohrer <shawn.bohrer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a driver for the 3 High Speed UARTs of the LPC32xx SoC that
support up to 921600bps. These UARTs are different from the 4 "Standard" UARTs
of the LPC32xx.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a "compatible" string for the new 8250 UART type PORT_LPC3220.
This is necessary for initializing LPC32xx UARTs via DT.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPC32xx has "Standard" UARTs that are actually 16550A compatible but have
bigger FIFOs. Since the already supported 16X50 line still doesn't match here,
we agreed on adding a new type.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We had a boot regression in Ux500 in the merge window because
two orthogonal pin control schemes for the PL011 were merged
at the same time:
- One using the .init() and .exit() hooks into the platform
for Ux500 putting the pins into default vs sleep state
respectively as the port was started/stopped.
commit a09806607f
"ARM: ux500: switch to using pinctrl for uart0"
- One hogging the default setting at PL011 probe()
commit 258e055111
"serial: amba-pl011: adopt pinctrl support"
To get a solution that works for both let's scrap the stuff
in the platform callbacks, instead have the driver itself
select default and sleep states when the port is
started/stopped. Hopefully this works for all clients.
Platform callbacks are bad for device tree migration anyway,
so this rids us of another problem in Ux500.
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix kconfig symbol test to use "defined":
drivers/tty/serial/serial_txx9.c: warning: "CONFIG_CONSOLE_POLL" is not defined [-Wundef]
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix kernel-doc warnings in drivers/tty/serial/8250/8250.c:
Warning(drivers/tty/serial/8250/8250.c:3128): No description found for parameter 'up'
Warning(drivers/tty/serial/8250/8250.c:3128): Excess function parameter 'port' description in 'serial8250_register_8250_port'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, serial drivers don't report buffer overruns. When a buffer overrun
occurs, tty_insert_flip_char returns 0, and no attempt is made to insert that
same character again (i.e. it is lost). This patch reports buffer overruns via
the buf_overrun field in the port's icount structure.
Signed-off-by: Corbin Atkinson <corbin.atkinson@xxxxxx>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is only cosmetic for now. In case that
http://mid.gmane.org/1335171381-24869-1-git-send-email-u.kleine-koenig@pengutronix.de
will be applied, it fixes a warning
drivers/tty/serial/imx.c: In function 'serial_imx_probe_dt':
drivers/tty/serial/imx.c:1430:17: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
though.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When priting the serial clock source, if clock source name is null,
kernel reference NULL point.
Signed-off-by: KeyYoung Park <keyyoung.park@samsung.com>
Signed-off-by: Huisung Kang <hs1218.kang@samsung.com>
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
port->baudclk_rate should be compared to the rate of port->baudclk,
because port->baudclk_rate was assigned as the rate of port->baudclk previously.
So to check that the current baudclk rate is same as previous rate,
the target of comparison sholud be the rate of port->baudclk.
Signed-off-by: Jun-Ho, Yoon <junho78.yoon@samsung.com>
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts the tty layer change to use per-tty locking, because it's
not correct yet, and fixing it will require some more deep surgery.
The main revert is d29f3ef39b ("tty_lock: Localise the lock"), but
there are several smaller commits that built upon it, they also get
reverted here. The list of reverted commits is:
fde86d3108 - tty: add lockdep annotations
8f6576ad47 - tty: fix ldisc lock inversion trace
d3ca8b64b9 - pty: Fix lock inversion
b1d679afd7 - tty: drop the pty lock during hangup
abcefe5fc3 - tty/amiserial: Add missing argument for tty_unlock()
fd11b42e35 - cris: fix missing tty arg in wait_event_interruptible_tty call
d29f3ef39b - tty_lock: Localise the lock
The revert had a trivial conflict in the 68360serial.c staging driver
that got removed in the meantime.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tty_lock_pair() do the right thing to avoid deadlocks, but should
instruct LOCKDEP of this to avoid a splat.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MIPS updates from Ralf Baechle:
"The whole series has been sitting in -next for quite a while with no
complaints. The last change to the series was before the weekend the
removal of an SPI patch which Grant - even though previously acked by
himself - appeared to raise objections. So I removed it until the
situation is clarified. Other than that all the patches have the acks
from their respective maintainers, all MIPS and x86 defconfigs are
building fine and I'm not aware of any problems introduced by this
series.
Among the key features for this patch series is a sizable patchset for
Lantiq which among other things introduces support for Lantiq's
flagship product, the FALCON SOC. It also means that the opensource
developers behind this patchset have overtaken Lantiq's competing
inhouse development team that was working behind closed doors.
Less noteworthy the ath79 patchset which adds support for a few more
chip variants, cleanups and fixes. Finally the usual dose of tweaking
of generic code."
Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
MIPS: lantiq: remove orphaned code
MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
MIPS: lantiq: implement support for FALCON soc
MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
MTD: MIPS: lantiq: implement OF support
watchdog: MIPS: lantiq: implement OF support and minor fixes
SERIAL: MIPS: lantiq: implement OF support
GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
MIPS: pci: convert lantiq driver to OF
MIPS: lantiq: convert dma to platform driver
MIPS: lantiq: implement support for clkdev api
MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
OF: MIPS: lantiq: implement irq_domain support
OF: MIPS: lantiq: implement OF support
MIPS: lantiq: drop mips_machine support
OF: PCI: const usage needed by MIPS
MIPS: Cavium: Remove smp_reserve_lock.
MIPS: Move cache setup to setup_arch().
...
This is caused by tty_release using tty_lock_pair to lock both sides of
the pty/tty pair, and then tty_ldisc_release dropping and relocking one
side only. We can drop both fine, so drop both to avoid any lock
ordering concerns.
Rework the release path to fix the new locking model.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ptmx_open path takes the tty and devpts locks in the wrong order
because tty_init_dev locks and returns a locked tty. As far as I can
tell this is actually safe anyway because the tty being returned is new
so nobody can get a reference to lock it at this point.
However we don't even need the devpts lock at this point, it's only held
as a byproduct of the way the locks were pushe down.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
We need to make sure that those parameters are setup to be correct.
As such the value of 0 is deemed invalid and we find that we
bail out. The hypervisor sets by default all of them to be zero
and when the hypercall is done does a simple:
a.value = d->arch.hvm_domain.params[a.index];
Which means that if the Xen toolstack forgot to setup the proper
HVM_PARAM_CONSOLE_EVTCHN (or the PFN one), we would get the
default value of 0 and use that.
CC: stable@kernel.org
Fixes-Oracle-Bug: 14091238
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We weren't resetting the parameter to be passed in to a
known default. Nor were we checking the return value of
hvm_get_parameter.
CC: stable@kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
All of the error paths are doing the same logic. In which
case we might as well collapse them in one path.
CC: stable@kernel.org
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Pull the MCA deletion branch from Paul Gortmaker:
"It was good that we could support MCA machines back in the day, but
realistically, nobody is using them anymore. They were mostly limited
to 386-sx 16MHz CPU and some 486 class machines and never more than
64MB of RAM. Even the enthusiast hobbyist community seems to have
dried up close to ten years ago, based on what you can find searching
various websites dedicated to the relatively short lived hardware.
So lets remove the support relating to CONFIG_MCA. There is no point
carrying this forward, wasting cycles doing routine maintenance on it;
wasting allyesconfig build time on validating it, wasting I/O on git
grep'ping over it, and so on."
Let's see if anybody screams. It generally has compiled, and James
Bottomley pointed out that there was a MCA extension from NCR that
allowed for up to 4GB of memory and PPro-class machines. So in *theory*
there may be users out there.
But even James (technically listed as a maintainer) doesn't actually
have a system, and while Alan Cox claims to have a machine in his cellar
that he offered to anybody who wants to take it off his hands, he didn't
argue for keeping MCA support either.
So we could bring it back. But somebody had better speak up and talk
about how they have actually been using said MCA hardware with modern
kernels for us to do that. And David already took the patch to delete
all the networking driver code (commit a5e371f61a: "drivers/net:
delete all code/drivers depending on CONFIG_MCA").
* 'delete-mca' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MCA: delete all remaining traces of microchannel bus support.
scsi: delete the MCA specific drivers and driver code
serial: delete the MCA specific 8250 support.
arm: remove ability to select CONFIG_MCA
