There are two things we need to take care of when we create block
mappings in the stage 2 page tables:
(1) The alignment within a PMD between the host address range and the
guest IPA range must be the same, since otherwise we end up mapping
pages with the wrong offset.
(2) The head and tail of a memory slot may not cover a full block
size, and we have to take care to not map those with block
descriptors, since we could expose memory to the guest that the host
did not intend to expose.
So far, we have been taking care of (1), but not (2), and our commentary
describing (1) was somewhat confusing.
This commit attempts to factor out the checks of both into a common
function, and if we don't pass the check, we won't attempt any PMD
mappings for neither hugetlbfs nor THP.
Note that we used to only check the alignment for THP, not for
hugetlbfs, but as far as I can tell the check needs to be applied to
both scenarios.
Cc: Ralph Palutke <ralph.palutke@fau.de>
Cc: Lukas Braun <koomi@moshbit.net>
Reported-by: Lukas Braun <koomi@moshbit.net>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In attempting to re-construct the logic for our stage 2 page table
layout I found the reasoning in the comment explaining how we calculate
the number of levels used for stage 2 page tables a bit backwards.
This commit attempts to clarify the comment, to make it slightly easier
to read without having the Arm ARM open on the right page.
While we're at it, fixup a typo in a comment that was recently changed.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
KVM only supports PMD hugepages at stage 2. Now that the various page
handling routines are updated, extend the stage 2 fault handling to
map in PUD hugepages.
Addition of PUD hugepage support enables additional page sizes (e.g.,
1G with 4K granule) which can be useful on cores that support mapping
larger block sizes in the TLB entries.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
[ Replace BUG() => WARN_ON(1) for arm32 PUD helpers ]
Signed-off-by: Suzuki Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In preparation for creating larger hugepages at Stage 2, add support
to the age handling notifiers for PUD hugepages when encountered.
Provide trivial helpers for arm32 to allow sharing code.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
[ Replaced BUG() => WARN_ON(1) for arm32 PUD helpers ]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In preparation for creating larger hugepages at Stage 2, extend the
access fault handling at Stage 2 to support PUD hugepages when
encountered.
Provide trivial helpers for arm32 to allow sharing of code.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
[ Replaced BUG() => WARN_ON(1) in PUD helpers ]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In preparation for creating PUD hugepages at stage 2, add support for
detecting execute permissions on PUD page table entries. Faults due to
lack of execute permissions on page table entries is used to perform
i-cache invalidation on first execute.
Provide trivial implementations of arm32 helpers to allow sharing of
code.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
[ Replaced BUG() => WARN_ON(1) in arm32 PUD helpers ]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In preparation for creating PUD hugepages at stage 2, add support for
write protecting PUD hugepages when they are encountered. Write
protecting guest tables is used to track dirty pages when migrating
VMs.
Also, provide trivial implementations of required kvm_s2pud_* helpers
to allow sharing of code with arm32.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
[ Replaced BUG() => WARN_ON() in arm32 pud helpers ]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Introduce helpers to abstract architectural handling of the conversion
of pfn to page table entries and marking a PMD page table entry as a
block entry.
The helpers are introduced in preparation for supporting PUD hugepages
at stage 2 - which are supported on arm64 but do not exist on arm.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Stage 2 fault handler marks a page as executable if it is handling an
execution fault or if it was a permission fault in which case the
executable bit needs to be preserved.
The logic to decide if the page should be marked executable is
duplicated for PMD and PTE entries. To avoid creating another copy
when support for PUD hugepages is introduced refactor the code to
share the checks needed to mark a page table entry as executable.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The code for operations such as marking the pfn as dirty, and
dcache/icache maintenance during stage 2 fault handling is duplicated
between normal pages and PMD hugepages.
Instead of creating another copy of the operations when we introduce
PUD hugepages, let's share them across the different pagesizes.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
ARM:
- Improved guest IPA space support (32 to 52 bits)
- RAS event delivery for 32bit
- PMU fixes
- Guest entry hardening
- Various cleanups
- Port of dirty_log_test selftest
PPC:
- Nested HV KVM support for radix guests on POWER9. The performance is
much better than with PR KVM. Migration and arbitrary level of
nesting is supported.
- Disable nested HV-KVM on early POWER9 chips that need a particular hardware
bug workaround
- One VM per core mode to prevent potential data leaks
- PCI pass-through optimization
- merge ppc-kvm topic branch and kvm-ppc-fixes to get a better base
s390:
- Initial version of AP crypto virtualization via vfio-mdev
- Improvement for vfio-ap
- Set the host program identifier
- Optimize page table locking
x86:
- Enable nested virtualization by default
- Implement Hyper-V IPI hypercalls
- Improve #PF and #DB handling
- Allow guests to use Enlightened VMCS
- Add migration selftests for VMCS and Enlightened VMCS
- Allow coalesced PIO accesses
- Add an option to perform nested VMCS host state consistency check
through hardware
- Automatic tuning of lapic_timer_advance_ns
- Many fixes, minor improvements, and cleanups
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJb0FINAAoJEED/6hsPKofoI60IAJRS3vOAQ9Fav8cJsO1oBHcX
3+NexfnBke1bzrjIR3SUcHKGZbdnVPNZc+Q4JjIbPpPmmOMU5jc9BC1dmd5f4Vzh
BMnQ0yCvgFv3A3fy/Icx1Z8NJppxosdmqdQLrQrNo8aD3cjnqY2yQixdXrAfzLzw
XEgKdIFCCz8oVN/C9TT4wwJn6l9OE7BM5bMKGFy5VNXzMu7t64UDOLbbjZxNgi1g
teYvfVGdt5mH0N7b2GPPWRbJmgnz5ygVVpVNQUEFrdKZoCm6r5u9d19N+RRXAwan
ZYFj10W2T8pJOUf3tryev4V33X7MRQitfJBo4tP5hZfi9uRX89np5zP1CFE7AtY=
=yEPW
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.20-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"ARM:
- Improved guest IPA space support (32 to 52 bits)
- RAS event delivery for 32bit
- PMU fixes
- Guest entry hardening
- Various cleanups
- Port of dirty_log_test selftest
PPC:
- Nested HV KVM support for radix guests on POWER9. The performance
is much better than with PR KVM. Migration and arbitrary level of
nesting is supported.
- Disable nested HV-KVM on early POWER9 chips that need a particular
hardware bug workaround
- One VM per core mode to prevent potential data leaks
- PCI pass-through optimization
- merge ppc-kvm topic branch and kvm-ppc-fixes to get a better base
s390:
- Initial version of AP crypto virtualization via vfio-mdev
- Improvement for vfio-ap
- Set the host program identifier
- Optimize page table locking
x86:
- Enable nested virtualization by default
- Implement Hyper-V IPI hypercalls
- Improve #PF and #DB handling
- Allow guests to use Enlightened VMCS
- Add migration selftests for VMCS and Enlightened VMCS
- Allow coalesced PIO accesses
- Add an option to perform nested VMCS host state consistency check
through hardware
- Automatic tuning of lapic_timer_advance_ns
- Many fixes, minor improvements, and cleanups"
* tag 'kvm-4.20-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (204 commits)
KVM/nVMX: Do not validate that posted_intr_desc_addr is page aligned
Revert "kvm: x86: optimize dr6 restore"
KVM: PPC: Optimize clearing TCEs for sparse tables
x86/kvm/nVMX: tweak shadow fields
selftests/kvm: add missing executables to .gitignore
KVM: arm64: Safety check PSTATE when entering guest and handle IL
KVM: PPC: Book3S HV: Don't use streamlined entry path on early POWER9 chips
arm/arm64: KVM: Enable 32 bits kvm vcpu events support
arm/arm64: KVM: Rename function kvm_arch_dev_ioctl_check_extension()
KVM: arm64: Fix caching of host MDCR_EL2 value
KVM: VMX: enable nested virtualization by default
KVM/x86: Use 32bit xor to clear registers in svm.c
kvm: x86: Introduce KVM_CAP_EXCEPTION_PAYLOAD
kvm: vmx: Defer setting of DR6 until #DB delivery
kvm: x86: Defer setting of CR2 until #PF delivery
kvm: x86: Add payload operands to kvm_multiple_exception
kvm: x86: Add exception payload fields to kvm_vcpu_events
kvm: x86: Add has_payload and payload to kvm_queued_exception
KVM: Documentation: Fix omission in struct kvm_vcpu_events
KVM: selftests: add Enlightened VMCS test
...
Pull siginfo updates from Eric Biederman:
"I have been slowly sorting out siginfo and this is the culmination of
that work.
The primary result is in several ways the signal infrastructure has
been made less error prone. The code has been updated so that manually
specifying SEND_SIG_FORCED is never necessary. The conversion to the
new siginfo sending functions is now complete, which makes it
difficult to send a signal without filling in the proper siginfo
fields.
At the tail end of the patchset comes the optimization of decreasing
the size of struct siginfo in the kernel from 128 bytes to about 48
bytes on 64bit. The fundamental observation that enables this is by
definition none of the known ways to use struct siginfo uses the extra
bytes.
This comes at the cost of a small user space observable difference.
For the rare case of siginfo being injected into the kernel only what
can be copied into kernel_siginfo is delivered to the destination, the
rest of the bytes are set to 0. For cases where the signal and the
si_code are known this is safe, because we know those bytes are not
used. For cases where the signal and si_code combination is unknown
the bits that won't fit into struct kernel_siginfo are tested to
verify they are zero, and the send fails if they are not.
I made an extensive search through userspace code and I could not find
anything that would break because of the above change. If it turns out
I did break something it will take just the revert of a single change
to restore kernel_siginfo to the same size as userspace siginfo.
Testing did reveal dependencies on preferring the signo passed to
sigqueueinfo over si->signo, so bit the bullet and added the
complexity necessary to handle that case.
Testing also revealed bad things can happen if a negative signal
number is passed into the system calls. Something no sane application
will do but something a malicious program or a fuzzer might do. So I
have fixed the code that performs the bounds checks to ensure negative
signal numbers are handled"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (80 commits)
signal: Guard against negative signal numbers in copy_siginfo_from_user32
signal: Guard against negative signal numbers in copy_siginfo_from_user
signal: In sigqueueinfo prefer sig not si_signo
signal: Use a smaller struct siginfo in the kernel
signal: Distinguish between kernel_siginfo and siginfo
signal: Introduce copy_siginfo_from_user and use it's return value
signal: Remove the need for __ARCH_SI_PREABLE_SIZE and SI_PAD_SIZE
signal: Fail sigqueueinfo if si_signo != sig
signal/sparc: Move EMT_TAGOVF into the generic siginfo.h
signal/unicore32: Use force_sig_fault where appropriate
signal/unicore32: Generate siginfo in ucs32_notify_die
signal/unicore32: Use send_sig_fault where appropriate
signal/arc: Use force_sig_fault where appropriate
signal/arc: Push siginfo generation into unhandled_exception
signal/ia64: Use force_sig_fault where appropriate
signal/ia64: Use the force_sig(SIGSEGV,...) in ia64_rt_sigreturn
signal/ia64: Use the generic force_sigsegv in setup_frame
signal/arm/kvm: Use send_sig_mceerr
signal/arm: Use send_sig_fault where appropriate
signal/arm: Use force_sig_fault where appropriate
...
PageTransCompoundMap() returns true for hugetlbfs and THP
hugepages. This behaviour incorrectly leads to stage 2 faults for
unsupported hugepage sizes (e.g., 64K hugepage with 4K pages) to be
treated as THP faults.
Tighten the check to filter out hugetlbfs pages. This also leads to
consistently mapping all unsupported hugepage sizes as PTE level
entries at stage 2.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Suzuki Poulose <suzuki.poulose@arm.com>
Cc: Christoffer Dall <christoffer.dall@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Right now the stage2 page table for a VM is hard coded, assuming
an IPA of 40bits. As we are about to add support for per VM IPA,
prepare the stage2 page table helpers to accept the kvm instance
to make the right decision for the VM. No functional changes.
Adds stage2_pgd_size(kvm) to replace S2_PGD_SIZE. Also, moves
some of the definitions in arm32 to align with the arm64.
Also drop the _AC() specifier constants wherever possible.
Cc: Christoffer Dall <cdall@kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On a 4-level page table pgd entry can be empty, unlike a 3-level
page table. Remove the spurious WARN_ON() in stage_get_pud().
Acked-by: Christoffer Dall <cdall@kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far we have only supported 3 level page table with fixed IPA of
40bits, where PUD is folded. With 4 level page tables, we need
to check if the PUD entry is valid or not. Fix stage2_flush_memslot()
to do this check, before walking down the table.
Acked-by: Christoffer Dall <cdall@kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This simplifies the code making it clearer what is going on, and
making the siginfo generation easier to maintain.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
kvm_unmap_hva is long gone, and we only have kvm_unmap_hva_range to
deal with. Drop the now obsolete code.
Fixes: fb1522e099 ("KVM: update to new mmu_notifier semantic v2")
Cc: James Hogan <jhogan@kernel.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
When triggering a CoW, we unmap the RO page via an MMU notifier
(invalidate_range_start), and then populate the new PTE using another
one (change_pte). In the meantime, we'll have copied the old page
into the new one.
The problem is that the data for the new page is sitting in the
cache, and should the guest have an uncached mapping to that page
(or its MMU off), following accesses will bypass the cache.
In a way, this is similar to what happens on a translation fault:
We need to clean the page to the PoC before mapping it. So let's just
do that.
This fixes a KVM unit test regression observed on a HiSilicon platform,
and subsequently reproduced on Seattle.
Fixes: a9c0e12ebe ("KVM: arm/arm64: Only clean the dcache on translation fault")
Cc: stable@vger.kernel.org # v4.16+
Reported-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
When there is contention on faulting in a particular page table entry
at stage 2, the break-before-make requirement of the architecture can
lead to additional refaulting due to TLB invalidation.
Avoid this by skipping a page table update if the new value of the PTE
matches the previous value.
Cc: stable@vger.kernel.org
Fixes: d5d8184d35 ("KVM: ARM: Memory virtualization setup")
Reviewed-by: Suzuki Poulose <suzuki.poulose@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Contention on updating a PMD entry by a large number of vcpus can lead
to duplicate work when handling stage 2 page faults. As the page table
update follows the break-before-make requirement of the architecture,
it can lead to repeated refaults due to clearing the entry and
flushing the tlbs.
This problem is more likely when -
* there are large number of vcpus
* the mapping is large block mapping
such as when using PMD hugepages (512MB) with 64k pages.
Fix this by skipping the page table update if there is no change in
the entry being updated.
Cc: stable@vger.kernel.org
Fixes: ad361f093c ("KVM: ARM: Support hugetlbfs backed huge pages")
Reviewed-by: Suzuki Poulose <suzuki.poulose@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is no need to perform cache maintenance operations when
creating the HYP page tables if we have the multiprocessing
extensions. ARMv7 mandates them with the virtualization support,
and ARMv8 just mandates them unconditionally.
Let's remove these operations.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The {pmd,pud,pgd}_populate accessors usage have always been a bit weird
in KVM. We don't have a struct mm to pass (and neither does the kernel
most of the time, but still...), and the 32bit code has all kind of
cache maintenance that doesn't make sense on ARMv7+ when MP extensions
are mandatory (which is the case when the VEs are present).
Let's bite the bullet and provide our own implementations. The only bit
of architectural code left has to do with building the table entry
itself (arm64 having up to 52bit PA, arm lacking PUD level).
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The arm and arm64 KVM page tables accessors are pointlessly different
between the two architectures, and likely both wrong one way or another:
arm64 lacks a dsb(), and arm doesn't use WRITE_ONCE.
Let's unify them.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Up to ARMv8.3, the combinaison of Stage-1 and Stage-2 attributes
results in the strongest attribute of the two stages. This means
that the hypervisor has to perform quite a lot of cache maintenance
just in case the guest has some non-cacheable mappings around.
ARMv8.4 solves this problem by offering a different mode (FWB) where
Stage-2 has total control over the memory attribute (this is limited
to systems where both I/O and instruction fetches are coherent with
the dcache). This is achieved by having a different set of memory
attributes in the page tables, and a new bit set in HCR_EL2.
On such a system, we can then safely sidestep any form of dcache
management.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is a panic in armv8a server(QDF2400) under memory pressure tests
(start 20 guests and run memhog in the host).
---------------------------------begin--------------------------------
[35380.800950] BUG: Bad page state in process qemu-kvm pfn:dd0b6
[35380.805825] page:ffff7fe003742d80 count:-4871 mapcount:-2126053375
mapping: (null) index:0x0
[35380.815024] flags: 0x1fffc00000000000()
[35380.818845] raw: 1fffc00000000000 0000000000000000 0000000000000000
ffffecf981470000
[35380.826569] raw: dead000000000100 dead000000000200 ffff8017c001c000
0000000000000000
[35380.805825] page:ffff7fe003742d80 count:-4871 mapcount:-2126053375
mapping: (null) index:0x0
[35380.815024] flags: 0x1fffc00000000000()
[35380.818845] raw: 1fffc00000000000 0000000000000000 0000000000000000
ffffecf981470000
[35380.826569] raw: dead000000000100 dead000000000200 ffff8017c001c000
0000000000000000
[35380.834294] page dumped because: nonzero _refcount
[...]
--------------------------------end--------------------------------------
The root cause might be what was fixed at [1]. But from the KVM points of
view, it would be better if the issue was caught earlier.
If the size is not PAGE_SIZE aligned, unmap_stage2_range might unmap the
wrong(more or less) page range. Hence it caused the "BUG: Bad page
state"
Let's WARN in that case, so that the issue is obvious.
[1] https://lkml.org/lkml/2018/5/3/1042
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: jia.he@hxt-semitech.com
[maz: tidied up commit message]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Call clear_siginfo to ensure every stack allocated siginfo is properly
initialized before being passed to the signal sending functions.
Note: It is not safe to depend on C initializers to initialize struct
siginfo on the stack because C is allowed to skip holes when
initializing a structure.
The initialization of struct siginfo in tracehook_report_syscall_exit
was moved from the helper user_single_step_siginfo into
tracehook_report_syscall_exit itself, to make it clear that the local
variable siginfo gets fully initialized.
In a few cases the scope of struct siginfo has been reduced to make it
clear that siginfo siginfo is not used on other paths in the function
in which it is declared.
Instances of using memset to initialize siginfo have been replaced
with calls clear_siginfo for clarity.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Until now, all EL2 executable mappings were derived from their
EL1 VA. Since we want to decouple the vectors mapping from
the rest of the hypervisor, we need to be able to map some
text somewhere else.
The "idmap" region (for lack of a better name) is ideally suited
for this, as we have a huge range that hardly has anything in it.
Let's extend the IO allocator to also deal with executable mappings,
thus providing the required feature.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The main idea behind randomising the EL2 VA is that we usually have
a few spare bits between the most significant bit of the VA mask
and the most significant bit of the linear mapping.
Those bits could be a bunch of zeroes, and could be useful
to move things around a bit. Of course, the more memory you have,
the less randomisation you get...
Alternatively, these bits could be the result of KASLR, in which
case they are already random. But it would be nice to have a
*different* randomization, just to make the job of a potential
attacker a bit more difficult.
Inserting these random bits is a bit involved. We don't have a spare
register (short of rewriting all the kern_hyp_va call sites), and
the immediate we want to insert is too random to be used with the
ORR instruction. The best option I could come up with is the following
sequence:
and x0, x0, #va_mask
ror x0, x0, #first_random_bit
add x0, x0, #(random & 0xfff)
add x0, x0, #(random >> 12), lsl #12
ror x0, x0, #(63 - first_random_bit)
making it a fairly long sequence, but one that a decent CPU should
be able to execute without breaking a sweat. It is of course NOPed
out on VHE. The last 4 instructions can also be turned into NOPs
if it appears that there is no free bits to use.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We so far mapped our HYP IO (which is essentially the GICv2 control
registers) using the same method as for memory. It recently appeared
that is a bit unsafe:
We compute the HYP VA using the kern_hyp_va helper, but that helper
is only designed to deal with kernel VAs coming from the linear map,
and not from the vmalloc region... This could in turn cause some bad
aliasing between the two, amplified by the upcoming VA randomisation.
A solution is to come up with our very own basic VA allocator for
MMIO. Since half of the HYP address space only contains a single
page (the idmap), we have plenty to borrow from. Let's use the idmap
as a base, and allocate downwards from it. GICv2 now lives on the
other side of the great VA barrier.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Unmapping the idmap range using 52bit PA is quite broken, as we
don't take into account the right number of PGD entries, and rely
on PTRS_PER_PGD. The result is that pgd_index() truncates the
address, and we end-up in the weed.
Let's introduce a new unmap_hyp_idmap_range() that knows about this,
together with a kvm_pgd_index() helper, which hides a bit of the
complexity of the issue.
Fixes: 98732d1b18 ("KVM: arm/arm64: fix HYP ID map extension to 52 bits")
Reported-by: James Morse <james.morse@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Although the idmap section of KVM can only be at most 4kB and
must be aligned on a 4kB boundary, the rest of the code expects
it to be page aligned. Things get messy when tearing down the
HYP page tables when PAGE_SIZE is 64K, and the idmap section isn't
64K aligned.
Let's fix this by computing aligned boundaries that the HYP code
will use.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: James Morse <james.morse@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're about to change the way we map devices at HYP, we need
to move away from kern_hyp_va on an IO address.
One way of achieving this is to store the VAs in kvm_vgic_global_state,
and use that directly from the HYP code. This requires a small change
to create_hyp_io_mappings so that it can also return a HYP VA.
We take this opportunity to nuke the vctrl_base field in the emulated
distributor, as it is not used anymore.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Both HYP io mappings call ioremap, followed by create_hyp_io_mappings.
Let's move the ioremap call into create_hyp_io_mappings itself, which
simplifies the code a bit and allows for further refactoring.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Displaying the HYP VA information is slightly counterproductive when
using VA randomization. Turn it into a debug feature only, and adjust
the last displayed value to reflect the top of RAM instead of ~0.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We currently have a separate read-modify-write of the HCR_EL2 on entry
to the guest for the sole purpose of setting the VF and VI bits, if set.
Since this is most rarely the case (only when using userspace IRQ chip
and interrupts are in flight), let's get rid of this operation and
instead modify the bits in the vcpu->arch.hcr[_el2] directly when
needed.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
ARM:
- Include icache invalidation optimizations, improving VM startup time
- Support for forwarded level-triggered interrupts, improving
performance for timers and passthrough platform devices
- A small fix for power-management notifiers, and some cosmetic changes
PPC:
- Add MMIO emulation for vector loads and stores
- Allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without
requiring the complex thread synchronization of older CPU versions
- Improve the handling of escalation interrupts with the XIVE interrupt
controller
- Support decrement register migration
- Various cleanups and bugfixes.
s390:
- Cornelia Huck passed maintainership to Janosch Frank
- Exitless interrupts for emulated devices
- Cleanup of cpuflag handling
- kvm_stat counter improvements
- VSIE improvements
- mm cleanup
x86:
- Hypervisor part of SEV
- UMIP, RDPID, and MSR_SMI_COUNT emulation
- Paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit
- Allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more AVX512
features
- Show vcpu id in its anonymous inode name
- Many fixes and cleanups
- Per-VCPU MSR bitmaps (already merged through x86/pti branch)
- Stable KVM clock when nesting on Hyper-V (merged through x86/hyperv)
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJafvMtAAoJEED/6hsPKofo6YcH/Rzf2RmshrWaC3q82yfIV0Qz
Z8N8yJHSaSdc3Jo6cmiVj0zelwAxdQcyjwlT7vxt5SL2yML+/Q0st9Hc3EgGGXPm
Il99eJEl+2MYpZgYZqV8ff3mHS5s5Jms+7BITAeh6Rgt+DyNbykEAvzt+MCHK9cP
xtsIZQlvRF7HIrpOlaRzOPp3sK2/MDZJ1RBE7wYItK3CUAmsHim/LVYKzZkRTij3
/9b4LP1yMMbziG+Yxt1o682EwJB5YIat6fmDG9uFeEVI5rWWN7WFubqs8gCjYy/p
FX+BjpOdgTRnX+1m9GIj0Jlc/HKMXryDfSZS07Zy4FbGEwSiI5SfKECub4mDhuE=
=C/uD
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"ARM:
- icache invalidation optimizations, improving VM startup time
- support for forwarded level-triggered interrupts, improving
performance for timers and passthrough platform devices
- a small fix for power-management notifiers, and some cosmetic
changes
PPC:
- add MMIO emulation for vector loads and stores
- allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without
requiring the complex thread synchronization of older CPU versions
- improve the handling of escalation interrupts with the XIVE
interrupt controller
- support decrement register migration
- various cleanups and bugfixes.
s390:
- Cornelia Huck passed maintainership to Janosch Frank
- exitless interrupts for emulated devices
- cleanup of cpuflag handling
- kvm_stat counter improvements
- VSIE improvements
- mm cleanup
x86:
- hypervisor part of SEV
- UMIP, RDPID, and MSR_SMI_COUNT emulation
- paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit
- allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more
AVX512 features
- show vcpu id in its anonymous inode name
- many fixes and cleanups
- per-VCPU MSR bitmaps (already merged through x86/pti branch)
- stable KVM clock when nesting on Hyper-V (merged through
x86/hyperv)"
* tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (197 commits)
KVM: PPC: Book3S: Add MMIO emulation for VMX instructions
KVM: PPC: Book3S HV: Branch inside feature section
KVM: PPC: Book3S HV: Make HPT resizing work on POWER9
KVM: PPC: Book3S HV: Fix handling of secondary HPTEG in HPT resizing code
KVM: PPC: Book3S PR: Fix broken select due to misspelling
KVM: x86: don't forget vcpu_put() in kvm_arch_vcpu_ioctl_set_sregs()
KVM: PPC: Book3S PR: Fix svcpu copying with preemption enabled
KVM: PPC: Book3S HV: Drop locks before reading guest memory
kvm: x86: remove efer_reload entry in kvm_vcpu_stat
KVM: x86: AMD Processor Topology Information
x86/kvm/vmx: do not use vm-exit instruction length for fast MMIO when running nested
kvm: embed vcpu id to dentry of vcpu anon inode
kvm: Map PFN-type memory regions as writable (if possible)
x86/kvm: Make it compile on 32bit and with HYPYERVISOR_GUEST=n
KVM: arm/arm64: Fixup userspace irqchip static key optimization
KVM: arm/arm64: Fix userspace_irqchip_in_use counting
KVM: arm/arm64: Fix incorrect timer_is_pending logic
MAINTAINERS: update KVM/s390 maintainers
MAINTAINERS: add Halil as additional vfio-ccw maintainer
MAINTAINERS: add David as a reviewer for KVM/s390
...
- Security mitigations:
- variant 2: invalidating the branch predictor with a call to secure firmware
- variant 3: implementing KPTI for arm64
- 52-bit physical address support for arm64 (ARMv8.2)
- arm64 support for RAS (firmware first only) and SDEI (software
delegated exception interface; allows firmware to inject a RAS error
into the OS)
- Perf support for the ARM DynamIQ Shared Unit PMU
- CPUID and HWCAP bits updated for new floating point multiplication
instructions in ARMv8.4
- Removing some virtual memory layout printks during boot
- Fix initial page table creation to cope with larger than 32M kernel
images when 16K pages are enabled
-----BEGIN PGP SIGNATURE-----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=iEjP
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"The main theme of this pull request is security covering variants 2
and 3 for arm64. I expect to send additional patches next week
covering an improved firmware interface (requires firmware changes)
for variant 2 and way for KPTI to be disabled on unaffected CPUs
(Cavium's ThunderX doesn't work properly with KPTI enabled because of
a hardware erratum).
Summary:
- Security mitigations:
- variant 2: invalidate the branch predictor with a call to
secure firmware
- variant 3: implement KPTI for arm64
- 52-bit physical address support for arm64 (ARMv8.2)
- arm64 support for RAS (firmware first only) and SDEI (software
delegated exception interface; allows firmware to inject a RAS
error into the OS)
- perf support for the ARM DynamIQ Shared Unit PMU
- CPUID and HWCAP bits updated for new floating point multiplication
instructions in ARMv8.4
- remove some virtual memory layout printks during boot
- fix initial page table creation to cope with larger than 32M kernel
images when 16K pages are enabled"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (104 commits)
arm64: Fix TTBR + PAN + 52-bit PA logic in cpu_do_switch_mm
arm64: Turn on KPTI only on CPUs that need it
arm64: Branch predictor hardening for Cavium ThunderX2
arm64: Run enable method for errata work arounds on late CPUs
arm64: Move BP hardening to check_and_switch_context
arm64: mm: ignore memory above supported physical address size
arm64: kpti: Fix the interaction between ASID switching and software PAN
KVM: arm64: Emulate RAS error registers and set HCR_EL2's TERR & TEA
KVM: arm64: Handle RAS SErrors from EL2 on guest exit
KVM: arm64: Handle RAS SErrors from EL1 on guest exit
KVM: arm64: Save ESR_EL2 on guest SError
KVM: arm64: Save/Restore guest DISR_EL1
KVM: arm64: Set an impdef ESR for Virtual-SError using VSESR_EL2.
KVM: arm/arm64: mask/unmask daif around VHE guests
arm64: kernel: Prepare for a DISR user
arm64: Unconditionally enable IESB on exception entry/return for firmware-first
arm64: kernel: Survive corrected RAS errors notified by SError
arm64: cpufeature: Detect CPU RAS Extentions
arm64: sysreg: Move to use definitions for all the SCTLR bits
arm64: cpufeature: __this_cpu_has_cap() shouldn't stop early
...
Commit fa2a8445b1 incorrectly masks the index of the HYP ID map pgd
entry, causing a non-VHE kernel to hang during boot. This happens when
VA_BITS=48 and the ID map text is in 52-bit physical memory. In this
case we don't need an extra table level but need more entries in the
top-level table, so we need to map into hyp_pgd and need to use
__kvm_idmap_ptrs_per_pgd to mask in the extra bits. However,
__create_hyp_mappings currently masks by PTRS_PER_PGD instead.
Fix it so that we always use __kvm_idmap_ptrs_per_pgd for the HYP ID
map. This ensures that we use the larger mask for the top-level ID map
table when it has more entries. In all other cases, PTRS_PER_PGD is used
as normal.
Fixes: fa2a8445b1 ("arm64: allow ID map to be extended to 52 bits")
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
KVM only supports PMD hugepages at stage 2 but doesn't actually check
that the provided hugepage memory pagesize is PMD_SIZE before populating
stage 2 entries.
In cases where the backing hugepage size is smaller than PMD_SIZE (such
as when using contiguous hugepages), KVM can end up creating stage 2
mappings that extend beyond the supplied memory.
Fix this by checking for the pagesize of userspace vma before creating
PMD hugepage at stage 2.
Fixes: 66b3923a1a ("arm64: hugetlb: add support for PTE contiguous bit")
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: <stable@vger.kernel.org> # v4.5+
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The vcpu parameter isn't used for anything, and gets in the way of
further cleanups. Let's get rid of it.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
So far, we loose the Exec property whenever we take permission
faults, as we always reconstruct the PTE/PMD from scratch. This
can be counter productive as we can end-up with the following
fault sequence:
X -> RO -> ROX -> RW -> RWX
Instead, we can lookup the existing PTE/PMD and clear the XN bit in the
new entry if it was already cleared in the old one, leadig to a much
nicer fault sequence:
X -> ROX -> RWX
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The only case where we actually need to perform a dcache maintenance
is when we map the page for the first time, and subsequent permission
faults do not require cache maintenance. Let's make it conditional
on not being a permission fault (and thus a translation fault).
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
We've so far eagerly invalidated the icache, no matter how
the page was faulted in (data or prefetch abort).
But we can easily track execution by setting the XN bits
in the S2 page tables, get the prefetch abort at HYP and
perform the icache invalidation at that time only.
As for most VMs, the instruction working set is pretty
small compared to the data set, this is likely to save
some traffic (specially as the invalidation is broadcast).
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
As we're about to introduce opportunistic invalidation of the icache,
let's split dcache and icache flushing.
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Currently, when using VA_BITS < 48, if the ID map text happens to be
placed in physical memory above VA_BITS, we increase the VA size (up to
48) and create a new table level, in order to map in the ID map text.
This is okay because the system always supports 48 bits of VA.
This patch extends the code such that if the system supports 52 bits of
VA, and the ID map text is placed that high up, then we increase the VA
size accordingly, up to 52.
One difference from the current implementation is that so far the
condition of VA_BITS < 48 has meant that the top level table is always
"full", with the maximum number of entries, and an extra table level is
always needed. Now, when VA_BITS = 48 (and using 64k pages), the top
level table is not full, and we simply need to increase the number of
entries in it, instead of creating a new table level.
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[catalin.marinas@arm.com: reduce arguments to __create_hyp_mappings()]
[catalin.marinas@arm.com: reworked/renamed __cpu_uses_extended_idmap_level()]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When we unmap the HYP memory, we try to be clever and unmap one
PGD at a time. If we start with a non-PGD aligned address and try
to unmap a whole PGD, things go horribly wrong in unmap_hyp_range
(addr and end can never match, and it all goes really badly as we
keep incrementing pgd and parse random memory as page tables...).
The obvious fix is to let unmap_hyp_range do what it does best,
which is to iterate over a range.
The size of the linear mapping, which begins at PAGE_OFFSET, can be
easily calculated by subtracting PAGE_OFFSET form high_memory, because
high_memory is defined as the linear map address of the last byte of
DRAM, plus one.
The size of the vmalloc region is given trivially by VMALLOC_END -
VMALLOC_START.
Cc: stable@vger.kernel.org
Reported-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The ARM-ARM has two bits in the ESR/HSR relevant to external aborts.
A range of {I,D}FSC values (of which bit 5 is always set) and bit 9 'EA'
which provides:
> an IMPLEMENTATION DEFINED classification of External Aborts.
This bit is in addition to the {I,D}FSC range, and has an implementation
defined meaning. KVM should always ignore this bit when handling external
aborts from a guest.
Remove the ESR_ELx_EA definition and rewrite its helper
kvm_vcpu_dabt_isextabt() to check the {I,D}FSC range. This merges
kvm_vcpu_dabt_isextabt() and the recently added is_abort_sea() helper.
CC: Tyler Baicar <tbaicar@codeaurora.org>
Reported-by: gengdongjiu <gengdj.1984@gmail.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
The mmu_notifier_release() callback of KVM triggers cleaning up
the stage2 page table on kvm-arm. However there could be other
notifier callbacks in parallel with the mmu_notifier_release(),
which could cause the call backs ending up in an empty stage2
page table. Make sure we check it for all the notifier callbacks.
Cc: stable@vger.kernel.org
Fixes: commit 293f29363 ("kvm-arm: Unmap shadow pagetables properly")
Reported-by: Alex Graf <agraf@suse.de>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Christoffer Dall