It isn't actually described clearly at all in UM10944.pdf, but on TX of
a management frame (such as PTP), this needs to happen:
- The destination MAC address (i.e. 01-80-c2-00-00-0e), along with the
desired destination port, need to be installed in one of the 4
management slots of the switch, over SPI.
- The host can poll over SPI for that management slot's ENFPORT field.
That gets unset when the switch has matched the slot to the frame.
And therein lies the problem. ENFPORT does not mean that the packet has
been transmitted. Just that it has been received over the CPU port, and
that the mgmt slot is yet again available.
This is relevant because of what we are doing in sja1105_ptp_txtstamp_skb,
which is called right after sja1105_mgmt_xmit. We are in a hard
real-time deadline, since the hardware only gives us 24 bits of TX
timestamp, so we need to read the full PTP clock to reconstruct it.
Because we're in a hurry (in an attempt to make sure that we have a full
64-bit PTP time which is as close as possible to the actual transmission
time of the frame, to avoid 24-bit wraparounds), first we read the PTP
clock, then we poll for the TX timestamp to become available.
But of course, we don't know for sure that the frame has been
transmitted when we read the full PTP clock. We had assumed that ENFPORT
means it has, but the assumption is incorrect. And while in most
real-life scenarios this has never been caught due to software delays,
nowhere is this fact more obvious than with a tc-taprio offload, where
PTP traffic gets a small timeslot very rarely (example: 1 packet per 10
ms). In that case, we will be reading the PTP clock for timestamp
reconstruction too early (before the packet has been transmitted), and
this renders the reconstruction procedure incorrect (see the assumptions
described in the comments found on function sja1105_tstamp_reconstruct).
So the PTP TX timestamps will be off by 1<<24 clock ticks, or 135 ms
(1 tick is 8 ns).
So fix this case of premature optimization by simply reordering the
sja1105_ptpegr_ts_poll and the sja1105_ptpclkval_read function calls. It
turns out that in practice, the 135 ms hard deadline for PTP timestamp
wraparound is not so hard, since even the most bandwidth-intensive PTP
profiles, such as 802.1AS-2011, have a sync frame interval of 125 ms.
So if we couldn't deliver a timestamp in 135 ms (which we can), we're
toast and have much bigger problems anyway.
Fixes: 47ed985e97 ("net: dsa: sja1105: Add logic for TX timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool rx and tx queue statistics are reporting wrong values.
Fix reading out the correct ones.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rocker_dma_rings_init, the goto blocks in case of errors
caused by the functions rocker_dma_cmd_ring_waits_alloc() and
rocker_dma_ring_create() are incorrect. The patch fixes the
order consistent with cleanup in rocker_dma_rings_fini().
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
During development we tried to make the interrupt handling as fine-grained
as possible with TX and RX interrupts being disabled/enabled independently
and the counter registers reset from workqueue context.
Unfortunately after thorough testing of current mainline, we noticed the
driver has become unstable under heavy load. While this is hard to
reproduce, it's quite consistent in the driver's current form.
This patch proposes to go back to the previous approach of doing all
processing in napi context with all interrupts masked in order to make the
driver usable in mainline linux. This doesn't impact the performance on
pumpkin boards at all and it's in line with what many ethernet drivers do
in mainline linux anyway.
At the same time we're adding a FIXME comment about the need to improve
the interrupt handling.
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will avoid many uneccessary error logs when driver or firmware is
in reset.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AER reset should follow the same steps as suspend/resume. We need to
free context memory during AER reset and allocate new context memory
during recovery by calling bnxt_hwrm_func_qcaps(). We also need
to call bnxt_reenable_sriov() to restore the VFs.
Fixes: bae361c54f ("bnxt_en: Improve AER slot reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If VFs are enabled, we need to re-configure them during resume because
firmware has been reset while resuming. Otherwise, the VFs won't
work after resume.
Fixes: c16d4ee0e3 ("bnxt_en: Refactor logic to re-enable SRIOV after firmware reset detected.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The separate steps we do in bnxt_resume() can be done more simply by
calling bnxt_hwrm_func_qcaps(). This change will add an extra
__bnxt_hwrm_func_qcaps() call which is needed anyway on older
firmware.
Fixes: f9b69d7f62 ("bnxt_en: Fix suspend/resume path on 57500 chips")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race condition exist during termination. The path is
alx_stop and then alx_remove. An alx_schedule_link_check could be called
before alx_stop by interrupt handler and invoke alx_link_check later.
Alx_stop frees the napis, and alx_remove cancels any pending works.
If any of the work is scheduled before termination and invoked before
alx_remove, a null-ptr-deref occurs because both expect alx->napis[i].
This patch fix the race condition by moving cancel_work_sync functions
before alx_free_napis inside alx_stop. Because interrupt handler can call
alx_schedule_link_check again, alx_free_irq is moved before
cancel_work_sync calls too.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VNIC driver's "login" command sequence is the final step
in the driver's initialization process with device firmware,
confirming the available device queue resources to be utilized
by the driver. Under high system load, firmware may not respond
to the request in a timely manner or may abort the request. In
such cases, the driver should reattempt the login command
sequence. In case of a device error, the number of retries
is bounded.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change added a disable to NAPI into macb_open, this was
intended to only happen on the error path but accidentally applies
to all paths. This causes NAPI to be disabled on the success path, which
leads to the network to no longer functioning.
Fixes: 014406babc ("net: cadence: macb: disable NAPI on error")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a comment. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
On AM65xx MCU CPSW2G NUSS and 66AK2E/L NUSS allmulti setting does not allow
unregistered mcast packets to pass.
This happens, because ALE VLAN entries on these SoCs do not contain port
masks for reg/unreg mcast packets, but instead store indexes of
ALE_VLAN_MASK_MUXx_REG registers which intended for store port masks for
reg/unreg mcast packets.
This path was missed by commit 9d1f644727 ("net: ethernet: ti: ale: fix
seeing unreg mcast packets with promisc and allmulti disabled").
Hence, fix it by taking into account ALE type in cpsw_ale_set_allmulti().
Fixes: 9d1f644727 ("net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc and allmulti disabled")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ALE parameters structure is created on stack, so it has to be reset
before passing to cpsw_ale_create() to avoid garbage values.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Ensure that all scheduled work items have completed before continuing
with device removal and after further event scheduling has been
halted. This patch fixes a bug where a scheduled driver reset event
is processed following device removal.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only QMAP endpoints should be configured to find a pad size field
within packet headers. They are found in the first byte of the QMAP
header (and the hardware fills only the 6 bits in that byte that
constitute the pad_len field).
The RMNet driver assumes the pad_len field is valid for received
packets, so we want to ensure the pad_len field is filled in that
case. That driver also assumes the length in the QMAP header
includes the pad bytes.
The RMNet driver does *not* pad the packets it sends, so the pad_len
field can be ignored.
Fix ipa_endpoint_init_hdr_ext() so it only marks the pad field
offset valid for QMAP RX endpoints, and in that case indicates
that the length field in the header includes the pad bytes.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The upper two nibbles of the sequencer type were not used for
SDM845, and were assumed to be 0. But for SC7180 they are used, and
so they must be programmed by ipa_endpoint_init_seq(). Fix this bug.
IPA_SEQ_PKT_PROCESS_NO_DEC_NO_UCP_DMAP doesn't have a descriptive
comment, so add one.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The endpoint id assigned to the modem LAN RX endpoint for the SC7180 SoC
is incorrect. The erroneous value might have been copied from SDM845 and
never updated. The correct endpoint id to use for this SoC is 11.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way the mask value is programmed for QMAP RX endpoints was based
on some wrong assumptions about the way metadata containing the QMAP
mux_id value is formatted. The metadata value supplied by the
modem is *not* in QMAP format, and in fact contains the mux_id we
want in its (big endian) low-order byte. That byte must be written
by the IPA into offset 1 of the QMAP header it inserts before the
received packet.
QMAP TX endpoints *do* use a QMAP header as the metadata sent with
each packet. The modem assumes this, and based on that assumes the
mux_id is in the second byte. To match those assumptions we must
program the modem TX (QMAP) endpoint HDR register to indicate the
metadata will be found at offset 0 in the message header.
The previous configuration managed to work, but it was not working
correctly. This patch fixes a bug whose symptom was receipt of
messages containing the wrong QMAP mux_id.
In fixing this, get rid of ipa_rmnet_mux_id_metadata_mask(), which
was more or less defined so there was a separate place to explain
what was happening as we generated the mask value. Instead, put a
longer description of how this works above ipa_endpoint_init_hdr(),
and define the metadata mask to use as a simple constant.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print the PCIe link information for our device.
Fixes: 77f972a707 ("ionic: remove support for mgmt device")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2020-06-11
This series contains fixes to the iavf driver.
Brett fixes the supported link speeds in the iavf driver, which was only
able to report speeds that the i40e driver supported and was missing the
speeds supported by the ice driver. In addition, fix how 2.5 and 5.0
GbE speeds are reported.
Alek fixes a enum comparison that was comparing two different enums that
may have different values, so update the comparison to use matching
enums.
Paul increases the time to complete a reset to allow for 128 VFs to
complete a reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't leave "counter" set to an error pointer. Otherwise either it
will lead to an error pointer dereference later in the function or it
leads to an error pointer dereference when we call mlx5_fc_destroy().
Fixes: 07bab95026 ("net/mlx5: E-Switch, Refactor eswitch ingress acl codes")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Clang warns:
drivers/net/ethernet/mellanox/mlx5/core/main.c:1278:6: warning: variable
'err' is used uninitialized whenever 'if' condition is true
[-Wsometimes-uninitialized]
if (!priv->dbg_root) {
^~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/main.c:1303:9: note:
uninitialized use occurs here
return err;
^~~
drivers/net/ethernet/mellanox/mlx5/core/main.c:1278:2: note: remove the
'if' if its condition is always false
if (!priv->dbg_root) {
^~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/main.c:1259:9: note: initialize
the variable 'err' to silence this warning
int err;
^
= 0
1 warning generated.
The check of returned value of debugfs_create_dir() is wrong because
by the design debugfs failures should never fail the driver and the
check itself was wrong too. The kernel compiled without CONFIG_DEBUG_FS
will return ERR_PTR(-ENODEV) and not NULL as expected.
Fixes: 11f3b84d70 ("net/mlx5: Split mdev init and pci init")
Link: https://github.com/ClangBuiltLinux/linux/issues/1042
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Set the ipv6 word fields according to the hardware definitions.
Fixes: ac991b48d4 ("net/mlx5e: CT: Offload established flows")
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current below problems exists.
1. devlink device is registered by mlx5_load_one(). But it is
not unregistered by mlx5_unload_one(). This is incorrect.
2. Above issue leads to,
When mlx5 PCI device is removed, currently devlink device is
unregistered before devlink ports are unregistered in below ladder
diagram.
remove_one()
mlx5_devlink_unregister()
[..]
devlink_unregister() <- ports are still registered!
mlx5_unload_one()
mlx5_unregister_device()
mlx5_remove_device()
mlx5e_remove()
mlx5e_devlink_port_unregister()
devlink_port_unregister()
3. Condition checking for registering and unregister device are not
symmetric either in these routines.
Hence, fix the sequence by having load and unload routines symmetric
and in right order.
i.e.
(a) register devlink device followed by registering devlink ports
(b) unregister devlink ports followed by devlink device
Do this based on boot and cleanup flags instead of different
conditions.
Fixes: c6acd629ee ("net/mlx5e: Add support for devlink-port in non-representors mode")
Fixes: f60f315d33 ("net/mlx5e: Register devlink ports for physical link, PCI PF, VFs")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
While unregistration is in progress, user might be reloading the
interface.
This can race with unregistration in below flow which uses the
resources which are getting disabled by reload flow.
Hence, disable the devlink reloading first when removing the device.
CPU0 CPU1
---- ----
local_pci_remove() devlink_mutex
remove_one() devlink_nl_cmd_reload()
mlx5_unregister_device() devlink_reload()
ops->reload_down()
mlx5_unload_one()
Fixes: 4383cfcc65 ("net/mlx5: Add devlink reload")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Changing RX hash function requires rearranging of RQT internal indexes,
the user isn't exposed to such changes and these changes do not affect
the user configured indirection table. Rebuild RQ table on hfunc change.
Fixes: bdfc028de1 ("net/mlx5e: Fix ethtool RX hash func configuration change")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
After an XSK is closed, the relevant structures in the channel are not
zeroed. If an XSK is opened the second time on the same channel without
recreating channels, the stray values in the structures will lead to
incorrect operation of queues, which causes CQE errors, and the new
socket doesn't work at all.
This patch fixes the issue by explicitly zeroing XSK-related structs in
the channel on XSK close. Note that those structs are zeroed on channel
creation, and usually a configuration change (XDP program is set)
happens on XSK open, which leads to recreating channels, so typical XSK
usecases don't suffer from this issue. However, if XSKs are opened and
closed on the same channel without removing the XDP program, this bug
reproduces.
Fixes: db05815b36 ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Variable "in" in dr_create_rc_qp() is allocated with kvzalloc() and
should be freed with kvfree().
Fixes: 297cccebdc ("net/mlx5: DR, Expose an internal API to issue RDMA operations")
Cc: stable@vger.kernel.org
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, in case of fatal error during mlx5_load_one(), we cannot
enter error state until mlx5_load_one() is finished, what can take
several minutes until commands will get timeouts, because these commands
can't be processed due to the fatal error.
Fix it by setting dev->state as MLX5_DEVICE_STATE_INTERNAL_ERROR before
requesting the lock.
Fixes: c1d4d2e92a ("net/mlx5: Avoid calling sleeping function by the health poll thread")
Signed-off-by: Shay Drory <shayd@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With an increased number of VFs, it's possible to encounter the following
issue during reset.
iavf b8d4:00:02.0: Hardware reset detected
iavf b8d4:00:02.0: Reset never finished (0)
iavf b8d4:00:02.0: Reset task did not complete, VF disabled
Increase the reset complete wait count to allow for 128 VFs to complete
reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 4ae4916b56 ("i40e: fix 'Unknown bps' in dmesg for 2.5Gb/5Gb
speeds") added the ability for the PF to report 2.5 and 5Gb speeds,
however, the iavf driver does not recognize those speeds as the values were
not added there. Add the proper enums and values so that iavf can properly
deal with those speeds.
Fixes: 4ae4916b56 ("i40e: fix 'Unknown bps' in dmesg for 2.5Gb/5Gb speeds")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Witold Fijalkowski <witoldx.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
adapter->link_speed has type enum virtchnl_link_speed but our comparisons
are against enum iavf_aq_link_speed. Though they are, currently, the same
values, change the comparison to the matching enum virtchnl_link_speed
since that may not always be the case.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Link speeds are communicated over virtchnl using an enum
virtchnl_link_speed. Currently, the highest link speed is 40Gbps which
leaves us unable to reflect some speeds that an ice VF is capable of.
This causes link speed to be misreported on the iavf driver.
Allow for communicating link speeds using Mbps so that the proper speed can
be reported for an ice VF. Moving away from the enum allows us to
communicate future speed changes without requiring a new enum to be added.
In order to support communicating link speeds over virtchnl in Mbps the
following functionality was added:
- Added u32 link_speed_mbps in the iavf_adapter structure.
- Added the macro ADV_LINK_SUPPORT(_a) to determine if the VF
driver supports communicating link speeds in Mbps.
- Added the function iavf_get_vpe_link_status() to fill the
correct link_status in the event_data union based on the
ADV_LINK_SUPPORT(_a) macro.
- Added the function iavf_set_adapter_link_speed_from_vpe()
to determine whether or not to fill the u32 link_speed_mbps or
enum virtchnl_link_speed link_speed field in the iavf_adapter
structure based on the ADV_LINK_SUPPORT(_a) macro.
- Do not free vf_res in iavf_init_get_resources() as vf_res will be
accessed in iavf_get_link_ksettings(); memset to 0 instead. This
memory is subsequently freed in iavf_remove().
Fixes: 7c710869d6 ("ice: Add handlers for VF netdevice operations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Sergey Nemov <sergey.nemov@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We no longer support the mgmt device in the ionic driver,
so remove the device id and related code.
Fixes: b3f064e974 ("ionic: add support for device id 0x1004")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "devm_kcalloc".
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio-mem
doorbell mapping for vdpa
config interrupt support in ifc
fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl7fZ6APHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpkDoIAMcBcQx5su1iuX7vT35xzUWZO478eAf1jOMZ
7KxKUVBeztkcxVFUlRVRu9MR6wOzwHils+1HD6025775Smr5M6x3aJxR6xOORaBj
RoU6OVGkpDvbzsxlhW+xhONz4O7/RkveKJPCwzGjqHrsFeh92lkfTqroz/EuNpw+
LZsO0+DhdUf123HbwHQp5lxW8EjyrRabgeZZg/D9VLPhoCP88vCjRhBXU2GPuaUl
/UNXsQafn4xUgrxPaoN5f4Phn/P46NNrbZ1jmlkw/z/3QhF/DhktGXGaZsIHDCN/
vicUii0or5QLeBsZpMbKko/BIe2xWHxFjkMRhMOMZOfcBb6sMBI=
=auUa
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
- virtio-mem: paravirtualized memory hotplug
- support doorbell mapping for vdpa
- config interrupt support in ifc
- fixes all over the place
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (40 commits)
vhost/test: fix up after API change
virtio_mem: convert device block size into 64bit
virtio-mem: drop unnecessary initialization
ifcvf: implement config interrupt in IFCVF
vhost: replace -1 with VHOST_FILE_UNBIND in ioctls
vhost_vdpa: Support config interrupt in vdpa
ifcvf: ignore continuous setting same status value
virtio-mem: Don't rely on implicit compiler padding for requests
virtio-mem: Try to unplug the complete online memory block first
virtio-mem: Use -ETXTBSY as error code if the device is busy
virtio-mem: Unplug subblocks right-to-left
virtio-mem: Drop manual check for already present memory
virtio-mem: Add parent resource for all added "System RAM"
virtio-mem: Better retry handling
virtio-mem: Offline and remove completely unplugged memory blocks
mm/memory_hotplug: Introduce offline_and_remove_memory()
virtio-mem: Allow to offline partially unplugged memory blocks
mm: Allow to offline unmovable PageOffline() pages via MEM_GOING_OFFLINE
virtio-mem: Paravirtualized memory hotunplug part 2
virtio-mem: Paravirtualized memory hotunplug part 1
...
vxlan driver should be using helpers to access nexthop struct
internals. Remove open check if whether nexthop is multipath in
favor of the existing nexthop_is_multipath helper. Add a new
helper, nexthop_has_v4, to cover the need to check has_v4 in
a group.
Fixes: 1274e1cc42 ("vxlan: ecmp support for mac fdb entries")
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fdb nexthops are marked with a flag. For standalone nexthops, a flag was
added to the nh_info struct. For groups that flag was added to struct
nexthop when it should have been added to the group information. Fix
by removing the flag from the nexthop struct and adding a flag to nh_group
that mirrors nh_info and is really only a caching of the individual types.
Add a helper, nexthop_is_fdb, for use by the vxlan code and fixup the
internal code to use the flag from either nh_info or nh_group.
v2
- propagate fdb_nh in remove_nh_grp_entry
Fixes: 38428d6871 ("nexthop: support for fdb ecmp nexthops")
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable frames injection in mvneta_xdp_xmit routine during hw
re-configuration in order to avoid hardware hangs
Fixes: b0a43db908 ("net: mvneta: add XDP_TX support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_running() test looks at __LINK_STATE_START which
gets set before ndo_open() is called, there is a window of
time between that and when the queues are actually ready to
be run. If ionic_check_link_status() notices that the link is
up very soon after netif_running() becomes true, it might try
to run the queues before they are ready, causing all manner of
potential issues. Since the netdev->flags IFF_UP isn't set
until after ndo_open() returns, we can wait for that before
we allow ionic_check_link_status() to start the queues.
On the way back to close, __LINK_STATE_START is cleared before
calling ndo_stop(), and IFF_UP is cleared after. Both of
these need to be true in order to safely stop the queues
from ionic_check_link_status().
Fixes: 49d3b49367 ("ionic: disable the queues on link down")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dynamic key update for addr_list_lock still causes troubles,
for example the following race condition still exists:
CPU 0: CPU 1:
(RCU read lock) (RTNL lock)
dev_mc_seq_show() netdev_update_lockdep_key()
-> lockdep_unregister_key()
-> netif_addr_lock_bh()
because lockdep doesn't provide an API to update it atomically.
Therefore, we have to move it back to static keys and use subclass
for nest locking like before.
In commit 1a33e10e4a ("net: partially revert dynamic lockdep key
changes"), I already reverted most parts of commit ab92d68fc2
("net: core: add generic lockdep keys").
This patch reverts the rest and also part of commit f3b0a18bb6
("net: remove unnecessary variables and callback"). After this
patch, addr_list_lock changes back to using static keys and
subclasses to satisfy lockdep. Thanks to dev->lower_level, we do
not have to change back to ->ndo_get_lock_subclass().
And hopefully this reduces some syzbot lockdep noises too.
Reported-by: syzbot+f3a0e80c34b3fc28ac5e@syzkaller.appspotmail.com
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The replacement of <asm/pgrable.h> with <linux/pgtable.h> made the include
of the latter in the middle of asm includes. Fix this up with the aid of
the below script and manual adjustments here and there.
import sys
import re
if len(sys.argv) is not 3:
print "USAGE: %s <file> <header>" % (sys.argv[0])
sys.exit(1)
hdr_to_move="#include <linux/%s>" % sys.argv[2]
moved = False
in_hdrs = False
with open(sys.argv[1], "r") as f:
lines = f.readlines()
for _line in lines:
line = _line.rstrip('
')
if line == hdr_to_move:
continue
if line.startswith("#include <linux/"):
in_hdrs = True
elif not moved and in_hdrs:
moved = True
print hdr_to_move
print line
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-4-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The include/linux/pgtable.h is going to be the home of generic page table
manipulation functions.
Start with moving asm-generic/pgtable.h to include/linux/pgtable.h and
make the latter include asm/pgtable.h.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-3-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "mm: consolidate definitions of page table accessors", v2.
The low level page table accessors (pXY_index(), pXY_offset()) are
duplicated across all architectures and sometimes more than once. For
instance, we have 31 definition of pgd_offset() for 25 supported
architectures.
Most of these definitions are actually identical and typically it boils
down to, e.g.
static inline unsigned long pmd_index(unsigned long address)
{
return (address >> PMD_SHIFT) & (PTRS_PER_PMD - 1);
}
static inline pmd_t *pmd_offset(pud_t *pud, unsigned long address)
{
return (pmd_t *)pud_page_vaddr(*pud) + pmd_index(address);
}
These definitions can be shared among 90% of the arches provided
XYZ_SHIFT, PTRS_PER_XYZ and xyz_page_vaddr() are defined.
For architectures that really need a custom version there is always
possibility to override the generic version with the usual ifdefs magic.
These patches introduce include/linux/pgtable.h that replaces
include/asm-generic/pgtable.h and add the definitions of the page table
accessors to the new header.
This patch (of 12):
The linux/mm.h header includes <asm/pgtable.h> to allow inlining of the
functions involving page table manipulations, e.g. pte_alloc() and
pmd_alloc(). So, there is no point to explicitly include <asm/pgtable.h>
in the files that include <linux/mm.h>.
The include statements in such cases are remove with a simple loop:
for f in $(git grep -l "include <linux/mm.h>") ; do
sed -i -e '/include <asm\/pgtable.h>/ d' $f
done
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-1-rppt@kernel.org
Link: http://lkml.kernel.org/r/20200514170327.31389-2-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
