commit fcec538ef8 upstream.
This resolves the hazard between the mtc0 in the change_c0_status() and
the mfc0 in configure_exception_vector(). Without resolving this hazard
configure_exception_vector() could read an old value and would restore
this old value again. This would revert the changes change_c0_status()
did. I checked this by printing out the read_c0_status() at the end of
per_cpu_trap_init() and the ST0_MX is not set without this patch.
The hazard is documented in the MIPS Architecture Reference Manual Vol.
III: MIPS32/microMIPS32 Privileged Resource Architecture (MD00088), rev
6.03 table 8.1 which includes:
Producer | Consumer | Hazard
----------|----------|----------------------------
mtc0 | mfc0 | any coprocessor 0 register
I saw this hazard on an Atheros AR9344 rev 2 SoC with a MIPS 74Kc CPU.
There the change_c0_status() function would activate the DSPen by
setting ST0_MX in the c0_status register. This was reverted and then the
system got a DSP exception when the DSP registers were saved in
save_dsp() in the first process switch. The crash looks like this:
[ 0.089999] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.097796] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.107070] Kernel panic - not syncing: Unexpected DSP exception
[ 0.113470] Rebooting in 1 seconds..
We saw this problem in OpenWrt only on the MIPS 74Kc based Atheros SoCs,
not on the 24Kc based SoCs. We only saw it with kernel 5.4 not with
kernel 4.19, in addition we had to use GCC 8.4 or 9.X, with GCC 8.3 it
did not happen.
In the kernel I bisected this problem to commit 9012d01166 ("compiler:
allow all arches to enable CONFIG_OPTIMIZE_INLINING"), but when this was
reverted it also happened after commit 172dcd935c ("MIPS: Always
allocate exception vector for MIPSr2+").
Commit 0b24cae4d5 ("MIPS: Add missing EHB in mtc0 -> mfc0 sequence.")
does similar changes to a different file. I am not sure if there are
more places affected by this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03e62fd67d upstream.
The dt-bindings for the GSWIP describe that the node should be named
"switch". Use the same name in sysctrl.c so the GSWIP driver can
actually find the "gphy0" and "gphy1" clocks.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 31e1b3efa8 ]
Register "a1" is unsaved in this function,
when CONFIG_TRACE_IRQFLAGS is enabled,
the TRACE_IRQS_OFF macro will call trace_hardirqs_off(),
and this may change register "a1".
The changed register "a1" as argument will be send
to do_fpe() and do_msa_fpe().
Signed-off-by: YuanJunQing <yuanjunqing66@163.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f33a0b9410 ]
There is a file descriptor resource leak in elf-entry.c, fix this
by adding fclose() before return and die.
Signed-off-by: Kaige Li <likaige@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed26aacfb5 ]
Loops-per-jiffies is a special number which represents a number of
noop-loop cycles per CPU-scheduler quantum - jiffies. As you
understand aside from CPU-specific implementation it depends on
the CPU frequency. So when a platform has the CPU frequency fixed,
we have no problem and the current udelay interface will work
just fine. But as soon as CPU-freq driver is enabled and the cores
frequency changes, we'll end up with distorted udelay's. In order
to fix this we have to accordinly adjust the per-CPU udelay_val
(the same as the global loops_per_jiffy) number. This can be done
in the CPU-freq transition event handler. We subscribe to that event
in the MIPS arch time-inititalization method.
Co-developed-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbb5946eb5 ]
Indeed according to the MIPS32 Privileged Resource Architecgture the MAAR
pair register address field either takes [12:31] bits for non-XPA systems
and [12:55] otherwise. In any case the current address mask is just
wrong for 64-bit and 32-bits XPA chips. So lets extend it to 59-bits
of physical address value. This shall cover the 64-bits architecture and
systems with XPA enabled, and won't cause any problem for non-XPA 32-bit
systems, since address values exceeding the architecture specific MAAR
mask will be just truncated with setting zeros in the unsupported upper
bits.
Co-developed-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a0efb8b10 ]
Commit 3885c2b463 ("MIPS: CM: Add support for reporting CM cache
errors") adds cm2_causes[] array with map of error type ID and
pointers to the short description string. There is a mistake in
the table, since according to MIPS32 manual CM2_ERROR_TYPE = {17,18}
correspond to INTVN_WR_ERR and INTVN_RD_ERR, while the table
claims they have {0x17,0x18} codes. This is obviously hex-dec
copy-paste bug. Moreover codes {0x18 - 0x1a} indicate L2 ECC errors.
Fixes: 3885c2b463 ("MIPS: CM: Add support for reporting CM cache errors")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-pm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff487d4103 ]
LLD failed to link vmlinux with 64bit load address for 32bit ELF
while bfd will strip 64bit address into 32bit silently.
To fix LLD build, we should truncate load address provided by platform
into 32bit for 32bit kernel.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/786
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=25784
Reviewed-by: Fangrui Song <maskray@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 269b3a9ac5 ]
In the current code, if CONFIG_SWIOTLB is set, when failed to get IO TLB
memory from the low pages by plat_swiotlb_setup(), it may lead to the boot
process failed with kernel panic.
(1) On the Loongson and SiByte platform
arch/mips/loongson64/dma.c
arch/mips/sibyte/common/dma.c
void __init plat_swiotlb_setup(void)
{
swiotlb_init(1);
}
kernel/dma/swiotlb.c
void __init
swiotlb_init(int verbose)
{
...
vstart = memblock_alloc_low(PAGE_ALIGN(bytes), PAGE_SIZE);
if (vstart && !swiotlb_init_with_tbl(vstart, io_tlb_nslabs, verbose))
return;
...
pr_warn("Cannot allocate buffer");
no_iotlb_memory = true;
}
phys_addr_t swiotlb_tbl_map_single()
{
...
if (no_iotlb_memory)
panic("Can not allocate SWIOTLB buffer earlier ...");
...
}
(2) On the Cavium OCTEON platform
arch/mips/cavium-octeon/dma-octeon.c
void __init plat_swiotlb_setup(void)
{
...
octeon_swiotlb = memblock_alloc_low(swiotlbsize, PAGE_SIZE);
if (!octeon_swiotlb)
panic("%s: Failed to allocate %zu bytes align=%lx\n",
__func__, swiotlbsize, PAGE_SIZE);
...
}
Because IO_TLB_DEFAULT_SIZE is 64M, if the rest size of low memory is less
than 64M when call plat_swiotlb_setup(), we can easily reproduce the panic
case.
In order to reduce the possibility of kernel panic when failed to get IO
TLB memory under CONFIG_SWIOTLB, it is better to allocate low memory as
small as possible before plat_swiotlb_setup(), so make sparse_init() using
top-down allocation.
Reported-by: Juxin Gao <gaojuxin@loongson.cn>
Co-developed-by: Juxin Gao <gaojuxin@loongson.cn>
Signed-off-by: Juxin Gao <gaojuxin@loongson.cn>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2ac81c6ef ]
Commit 1aeba347b3 ("MIPS: Hardcode cpu_has_mips* where target ISA
allows") updated the cpu_has_mips* macro to be replaced with a constant
expression where it's possible. By mistake it wasn't done correctly
for cpu_has_mips64r1/cpu_has_mips64r2 macro. They are defined to
be replaced with conditional expression __isa_range_or_flag(), which
means either ISA revision being within the range or the corresponding
CPU options flag was set at the probe stage or both being true at the
same time. But the ISA level value doesn't indicate whether the ISA is
MIPS32 or MIPS64. Due to this if we select MIPS32r1 - MIPS32r5
architectures the __isa_range() macro will activate the
cpu_has_mips64rX flags, which is incorrect. In order to fix the
problem we make sure the 64bits CPU support is enabled by means of
checking the flag cpu_has_64bits aside with proper ISA range and specific
Revision flag being set.
Fixes: 1aeba347b3 ("MIPS: Hardcode cpu_has_mips* where target ISA allows")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a44de7497f ]
When ATI Radeon GPU driver has been compiled directly into the kernel
instead of as a module, we should make sure the firmware for the model
(check available ones in /lib/firmware/radeon) is built-in to the kernel
as well, otherwise there exists the following fatal error during GPU init,
change CONFIG_DRM_RADEON=y to CONFIG_DRM_RADEON=m to fix it.
[ 1.900997] [drm] Loading RS780 Microcode
[ 1.905077] radeon 0000:01:05.0: Direct firmware load for radeon/RS780_pfp.bin failed with error -2
[ 1.914140] r600_cp: Failed to load firmware "radeon/RS780_pfp.bin"
[ 1.920405] [drm:r600_init] *ERROR* Failed to load firmware!
[ 1.926069] radeon 0000:01:05.0: Fatal error during GPU init
[ 1.931729] [drm] radeon: finishing device.
Fixes: 024e6a8b5b ("MIPS: Loongson: Add a Loongson-3 default config file")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5816c76dea upstream.
If a CPU support more than 32bit vmbits (which is true for 64bit CPUs),
VPN2_MASK set to fixed 0xffffe000 will lead to a wrong EntryHi in some
functions such as _kvm_mips_host_tlb_inv().
The cpu_vmbits definition of 32bit CPU in cpu-features.h is 31, so we
still use the old definition.
Cc: Stable <stable@vger.kernel.org>
Reviewed-by: Aleksandar Markovic <aleksandar.qemu.devel@gmail.com>
Signed-off-by: Xing Li <lixing@loongson.cn>
[Huacai: Improve commit messages]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Message-Id: <1590220602-3547-3-git-send-email-chenhc@lemote.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe2b73dba4 upstream.
The code in decode_config4() of arch/mips/kernel/cpu-probe.c
asid_mask = MIPS_ENTRYHI_ASID;
if (config4 & MIPS_CONF4_AE)
asid_mask |= MIPS_ENTRYHI_ASIDX;
set_cpu_asid_mask(c, asid_mask);
set asid_mask to cpuinfo->asid_mask.
So in order to support variable ASID_MASK, KVM_ENTRYHI_ASID should also
be changed to cpu_asid_mask(&boot_cpu_data).
Cc: Stable <stable@vger.kernel.org> #4.9+
Reviewed-by: Aleksandar Markovic <aleksandar.qemu.devel@gmail.com>
Signed-off-by: Xing Li <lixing@loongson.cn>
[Huacai: Change current_cpu_data to boot_cpu_data for optimization]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Message-Id: <1590220602-3547-2-git-send-email-chenhc@lemote.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 792a402c28 upstream.
There is a potential NULL pointer dereference in case kzalloc()
fails and returns NULL.
Fix this by adding a NULL check on *cd*
This bug was detected with the help of Coccinelle.
Fixes: 64b139f97c ("MIPS: OCTEON: irq: add CIB and other fixes")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d191aaffe3 upstream.
LDDIR/LDPTE is Loongson-3's acceleration for Page Table Walking. If BD
(Base Directory, the 4th page directory) is not enabled, then GDOffset
is biased by BadVAddr[63:62]. So, if GDOffset (aka. BadVAddr[47:36] for
Loongson-3) is big enough, "0b11(BadVAddr[63:62])|BadVAddr[47:36]|...."
can far beyond pg_swapper_dir. This means the pg_swapper_dir may NOT be
accessed by LDDIR correctly, so fix it by set PWDirExt in CP0_PWCtl.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pei Huang <huangpei@loongson.cn>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bef8e2dfce upstream.
Pointer on the memory allocated by 'alloc_progmem()' is stored in
'v->load_addr'. So this is this memory that should be freed by
'release_progmem()'.
'release_progmem()' is only a call to 'kfree()'.
With the current code, there is both a double free and a memory leak.
Fix it by passing the correct pointer to 'release_progmem()'.
Fixes: e01402b115 ("More AP / SP bits for the 34K, the Malta bits and things. Still wants")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: ralf@linux-mips.org
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel-janitors@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16202c0957 upstream.
Commit 92b34a9763 ("MIPS: boot: add missing targets for vmlinux.*.its")
fixed constant rebuild of *.its files on every make invocation, but due
to typo ("lzmo") it made no sense for vmlinux.lzma.its.
Fixes: 92b34a9763 ("MIPS: boot: add missing targets for vmlinux.*.its")
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
[paulburton@kernel.org: s/invokation/invocation/]
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Rob Herring <robh@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a53998802e upstream.
quiet_cmd_relocs lacks a whitespace which results in:
LD vmlinux
SORTEX vmlinux
SYSMAP System.map
RELOCS vmlinux
Building modules, stage 2.
MODPOST 64 modules
After this patch:
LD vmlinux
SORTEX vmlinux
SYSMAP System.map
RELOCS vmlinux
Building modules, stage 2.
MODPOST 64 modules
Typo is present in kernel tree since the introduction of relocatable
kernel support in commit e818fac595 ("MIPS: Generate relocation table
when CONFIG_RELOCATABLE"), but the relocation scripts were moved to
Makefile.postlink later with commit 44079d3509 ("MIPS: Use
Makefile.postlink to insert relocations into vmlinux").
Fixes: 44079d3509 ("MIPS: Use Makefile.postlink to insert relocations into vmlinux")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
[paulburton@kernel.org: Fixup commit references in commit message.]
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Rob Herring <robh@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a4a3893114 ]
__sanitizer_cov_trace_pc() is not linked in and causing link
failure if KCOV_INSTRUMENT is enabled. Fix this by disabling
instrumentation for compressed image.
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d2aa4bb90 ]
The libc provides a discovery mechanism for vDSO library and its
symbols. When a symbol is not exposed by the vDSOs the libc falls back
on the system calls.
With the introduction of the unified vDSO library on mips this behavior
is not honored anymore by the kernel in the case of gettimeofday().
The issue has been noticed and reported due to a dhclient failure on the
CI20 board:
root@letux:~# dhclient
../../../../lib/isc/unix/time.c:200: Operation not permitted
root@letux:~#
Restore the original behavior fixing gettimeofday() in the vDSO library.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com> # CI20 with JZ4780
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: mips-creator-ci20-dev@googlegroups.com
Cc: letux-kernel@openphoenux.org
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b1313eb32 ]
Report L1 caches as shared per core; L2 - per cluster.
This fixes "perf" that went crazy if shared_cpu_map attribute not
reported on sysfs, in form of
/sys/devices/system/cpu/cpu*/cache/index*/shared_cpu_list
/sys/devices/system/cpu/cpu*/cache/index*/shared_cpu_map
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e3d765a941 upstream.
If number of CPUs are limited by the kernel commandline parameter nr_cpus
assignment of interrupts accourding to numa rules might not be possibe.
As a fallback use one of the online CPUs as interrupt destination.
Fixes: 69a07a41d9 ("MIPS: SGI-IP27: rework HUB interrupts")
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e49e6f6db0 ]
All BPF JIT compilers except RISC-V's and MIPS' enforce a 33-tail calls
limit at runtime. In addition, a test was recently added, in tailcalls2,
to check this limit.
This patch updates the tail call limit in MIPS' JIT compiler to allow
33 tail calls.
Fixes: b6bd53f9c4 ("MIPS: Add missing file for eBPF JIT.")
Reported-by: Mahshid Khezri <khezri.mahshid@gmail.com>
Signed-off-by: Paul Chaignon <paul.chaignon@orange.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/b8eb2caac1c25453c539248e56ca22f74b5316af.1575916815.git.paul.chaignon@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bbcc5672b0 upstream.
Declaring __current_thread_info as a global register variable has the
effect of preventing GCC from saving & restoring its value in cases
where the ABI would typically do so.
To quote GCC documentation:
> If the register is a call-saved register, call ABI is affected: the
> register will not be restored in function epilogue sequences after the
> variable has been assigned. Therefore, functions cannot safely return
> to callers that assume standard ABI.
When our position independent VDSO is built for the n32 or n64 ABIs all
functions it exposes should be preserving the value of $gp/$28 for their
caller, but in the presence of the __current_thread_info global register
variable GCC stops doing so & simply clobbers $gp/$28 when calculating
the address of the GOT.
In cases where the VDSO returns success this problem will typically be
masked by the caller in libc returning & restoring $gp/$28 itself, but
that is by no means guaranteed. In cases where the VDSO returns an error
libc will typically contain a fallback path which will now fail
(typically with a bad memory access) if it attempts anything which
relies upon the value of $gp/$28 - eg. accessing anything via the GOT.
One fix for this would be to move the declaration of
__current_thread_info inside the current_thread_info() function,
demoting it from global register variable to local register variable &
avoiding inadvertently creating a non-standard calling ABI for the VDSO.
Unfortunately this causes issues for clang, which doesn't support local
register variables as pointed out by commit fe92da0f35 ("MIPS: Changed
current_thread_info() to an equivalent supported by both clang and GCC")
which introduced the global register variable before we had a VDSO to
worry about.
Instead, fix this by continuing to use the global register variable for
the kernel proper but declare __current_thread_info as a simple extern
variable when building the VDSO. It should never be referenced, and will
cause a link error if it is. This resolves the calling convention issue
for the VDSO without having any impact upon the build of the kernel
itself for either clang or gcc.
Signed-off-by: Paul Burton <paulburton@kernel.org>
Fixes: ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
Reported-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christian Brauner <christian.brauner@canonical.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: <stable@vger.kernel.org> # v4.4+
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f596cf0d80 upstream.
It is completely wrong to check for compile-time MIPS ISA revision in
the body of bpf_int_jit_compile() as it may lead to get MIPS JIT fully
omitted by the CC while the rest system will think that the JIT is
actually present and works [1].
We can check if the selected CPU really supports MIPS eBPF JIT at
configure time and avoid such situations when kernel can be built
without both JIT and interpreter, but with CONFIG_BPF_SYSCALL=y.
[1] https://lore.kernel.org/linux-mips/09d713a59665d745e21d021deeaebe0a@dlink.ru/
Fixes: 716850ab10 ("MIPS: eBPF: Initial eBPF support for MIPS32 architecture.")
Cc: <stable@vger.kernel.org> # v5.2+
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Hassan Naveed <hnaveed@wavecomp.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: Andrii Nakryiko <andriin@fb.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: bpf@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8fffebdea upstream.
Commit 716850ab10 ("MIPS: eBPF: Initial eBPF support for MIPS32
architecture.") enabled our eBPF JIT for MIPS32 kernels, whereas it has
previously only been availailable for MIPS64. It was my understanding at
the time that the BPF test suite was passing & JITing a comparable
number of tests to our cBPF JIT [1], but it turns out that was not the
case.
The eBPF JIT has a number of problems on MIPS32:
- Most notably various code paths still result in emission of MIPS64
instructions which will cause reserved instruction exceptions & kernel
panics when run on MIPS32 CPUs.
- The eBPF JIT doesn't account for differences between the O32 ABI used
by MIPS32 kernels versus the N64 ABI used by MIPS64 kernels. Notably
arguments beyond the first 4 are passed on the stack in O32, and this
is entirely unhandled when JITing a BPF_CALL instruction. Stack space
must be reserved for arguments even if they all fit in registers, and
the callee is free to assume that stack space has been reserved for
its use - with the eBPF JIT this is not the case, so calling any
function can result in clobbering values on the stack & unpredictable
behaviour. Function arguments in eBPF are always 64-bit values which
is also entirely unhandled - the JIT still uses a single (32-bit)
register per argument. As a result all function arguments are always
passed incorrectly when JITing a BPF_CALL instruction, leading to
kernel crashes or strange behavior.
- The JIT attempts to bail our on use of ALU64 instructions or 64-bit
memory access instructions. The code doing this at the start of
build_one_insn() incorrectly checks whether BPF_OP() equals BPF_DW,
when it should really be checking BPF_SIZE() & only doing so when
BPF_CLASS() is one of BPF_{LD,LDX,ST,STX}. This results in false
positives that cause more bailouts than intended, and that in turns
hides some of the problems described above.
- The kernel's cBPF->eBPF translation makes heavy use of 64-bit eBPF
instructions that the MIPS32 eBPF JIT bails out on, leading to most
cBPF programs not being JITed at all.
Until these problems are resolved, revert the enabling of the eBPF JIT
on MIPS32 done by commit 716850ab10 ("MIPS: eBPF: Initial eBPF support
for MIPS32 architecture.").
Note that this does not undo the changes made to the eBPF JIT by that
commit, since they are a useful starting point to providing MIPS32
support - they're just not nearly complete.
[1] https://lore.kernel.org/linux-mips/MWHPR2201MB13583388481F01A422CE7D66D4410@MWHPR2201MB1358.namprd22.prod.outlook.com/
Signed-off-by: Paul Burton <paulburton@kernel.org>
Fixes: 716850ab10 ("MIPS: eBPF: Initial eBPF support for MIPS32 architecture.")
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Hassan Naveed <hnaveed@wavecomp.com>
Cc: Tony Ambardar <itugrok@yahoo.com>
Cc: bpf@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: <stable@vger.kernel.org> # v5.2+
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d754a529a8 which was
commit 3c1d3f0979 upstream.
This breaks the build and should be reverted.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit dc9d0a75ce which is
commit fd7710cb49 upstream.
This, and the follow-on patch, breaks the mips build so it needs to be
reverted.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fd7710cb49 ]
Commit 3c1d3f0979 ("MIPS: futex: Emit Loongson3 sync workarounds
within asm") inadvertently removed the newlines following
__WEAK_LLSC_MB, which causes build failures for configurations in which
__WEAK_LLSC_MB expands to a sync instruction:
{standard input}: Assembler messages:
{standard input}:9346: Error: symbol `sync3' is already defined
{standard input}:9380: Error: symbol `sync3' is already defined
...
Fix this by restoring the newlines to separate the sync instruction from
anything following it (such as the 3: label), preventing inadvertent
concatenation.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 3c1d3f0979 ("MIPS: futex: Emit Loongson3 sync workarounds within asm")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ed6751bb8 ]
With CONFIG_MIPS_VA_BITS_48=y the build fails miserably:
CC arch/mips/kernel/asm-offsets.s
In file included from arch/mips/include/asm/pgtable.h:644,
from include/linux/mm.h:99,
from arch/mips/kernel/asm-offsets.c:15:
include/asm-generic/pgtable.h:16:2: error: #error CONFIG_PGTABLE_LEVELS is not consistent with __PAGETABLE_{P4D,PUD,PMD}_FOLDED
#error CONFIG_PGTABLE_LEVELS is not consistent with __PAGETABLE_{P4D,PUD,PMD}_FOLDED
^~~~~
include/asm-generic/pgtable.h:390:28: error: unknown type name 'p4d_t'; did you mean 'pmd_t'?
static inline int p4d_same(p4d_t p4d_a, p4d_t p4d_b)
^~~~~
pmd_t
[ ... more such errors ... ]
scripts/Makefile.build:99: recipe for target 'arch/mips/kernel/asm-offsets.s' failed
make[2]: *** [arch/mips/kernel/asm-offsets.s] Error 1
This happens because when CONFIG_MIPS_VA_BITS_48 enables 4th level of the
page tables, but neither pgtable-nop4d.h nor 5level-fixup.h are included to
cope with the 5th level.
Replace #ifdef conditions around includes of the pgtable-nop{m,u}d.h with
explicit CONFIG_PGTABLE_LEVELS and add include of 5level-fixup.h for the
case when CONFIG_PGTABLE_LEVELS==4
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mm@kvack.org
Cc: Mike Rapoport <rppt@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b2fa0c926 ]
Some versions of SoC MT7621 have three PCI express hosts. Some boards
make use of those PCI through the staging driver mt7621-pci. Recently
PCI support has been removed from MT7621 Soc kernel configuration due
to a build error. This makes imposible to compile staging driver and
produces a regression for gnubee based boards. Enable support for PCI
again but enable it only if staging mt7621-pci driver is selected.
Fixes: c4d48cf5e2 ("MIPS: ralink: deactivate PCI support for SOC_MT7621")
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: john@phrozen.org
Cc: NeilBrown <neil@brown.name>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20191019081233.7337-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c1d3f0979 ]
Generate the sync instructions required to workaround Loongson3 LL/SC
errata within inline asm blocks, which feels a little safer than doing
it from C where strictly speaking the compiler would be well within its
rights to insert a memory access between the separate asm statements we
previously had, containing sync & ll instructions respectively.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
MAINTAINERS update for Broadcom MIPS systems.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXc4wwBYccGF1bGJ1cnRv
bkBrZXJuZWwub3JnAAoJED6nn6y1dQDdgA4BAPUIK91zzLqrG5krdu5Df/UDM3EN
XlhhDTX8tT7QHvufAP9Uyn9FkbCIPmupBp+6s7Q6OvHGyG8TYRxTehyMtdLiBA==
=McJE
-----END PGP SIGNATURE-----
Merge tag 'mips_fixes_5.4_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A fix and simplification for SGI IP27 exception handlers, and a small
MAINTAINERS update for Broadcom MIPS systems"
* tag 'mips_fixes_5.4_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MAINTAINERS: Remove Kevin as maintainer of BMIPS generic platforms
MIPS: SGI-IP27: fix exception handler replication
The update of the VDSO data is depending on __arch_use_vsyscall() returning
True. This is a leftover from the attempt to map the features of various
architectures 1:1 into generic code.
The usage of __arch_use_vsyscall() in the actual vsyscall implementations
got dropped and replaced by the requirement for the architecture code to
return U64_MAX if the global clocksource is not usable in the VDSO.
But the __arch_use_vsyscall() check in the update code stayed which causes
the VDSO data to be stale or invalid when an architecture actually
implements that function and returns False when the current clocksource is
not usable in the VDSO.
As a consequence the VDSO implementations of clock_getres(), time(),
clock_gettime(CLOCK_.*_COARSE) operate on invalid data and return bogus
information.
Remove the __arch_use_vsyscall() check from the VDSO update function and
update the VDSO data unconditionally.
[ tglx: Massaged changelog and removed the now useless implementations in
asm-generic/ARM64/MIPS ]
Fixes: 44f57d788e ("timekeeping: Provide a generic update_vsyscall() implementation")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1571887709-11447-1-git-send-email-chenhc@lemote.com
Commit 775b089aef ("MIPS: tlbex: Remove cpu_has_local_ebase") removed
generating tlb refill handlers for every CPU, which was needed for
generating per node exception handlers on IP27. Instead of resurrecting
(and fixing) refill handler generation, we simply copy all exception
vectors from the boot node to the other nodes. Also remove the config
option since the memory tradeoff for expection handler replication
is just 8k per node.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
build_restore_pagemask() will restore the value of register $1/$at when
its restore_scratch argument is non-zero, and aims to do so by filling a
branch delay slot. Commit 0b24cae4d5 ("MIPS: Add missing EHB in mtc0
-> mfc0 sequence.") added an EHB instruction (Execution Hazard Barrier)
prior to restoring $1 from a KScratch register, in order to resolve a
hazard that can result in stale values of the KScratch register being
observed. In particular, P-class CPUs from MIPS with out of order
execution pipelines such as the P5600 & P6600 are affected.
Unfortunately this EHB instruction was inserted in the branch delay slot
causing the MFC0 instruction which performs the restoration to no longer
execute along with the branch. The result is that the $1 register isn't
actually restored, ie. the TLB refill exception handler clobbers it -
which is exactly the problem the EHB is meant to avoid for the P-class
CPUs.
Similarly build_get_pgd_vmalloc() will restore the value of $1/$at when
its mode argument equals refill_scratch, and suffers from the same
problem.
Fix this by in both cases moving the EHB earlier in the emitted code.
There's no reason it needs to immediately precede the MFC0 - it simply
needs to be between the MTC0 & MFC0.
This bug only affects Cavium Octeon systems which use
build_fast_tlb_refill_handler().
Signed-off-by: Paul Burton <paulburton@kernel.org>
Fixes: 0b24cae4d5 ("MIPS: Add missing EHB in mtc0 -> mfc0 sequence.")
Cc: Dmitry Korotin <dkorotin@wavecomp.com>
Cc: stable@vger.kernel.org # v3.15+
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
The vectors span more than one byte, so mark them as arrays.
Fixes the following build error when building when using GCC 8.3:
In file included from ./include/linux/string.h:19,
from ./include/linux/bitmap.h:9,
from ./include/linux/cpumask.h:12,
from ./arch/mips/include/asm/processor.h:15,
from ./arch/mips/include/asm/thread_info.h:16,
from ./include/linux/thread_info.h:38,
from ./include/asm-generic/preempt.h:5,
from ./arch/mips/include/generated/asm/preempt.h:1,
from ./include/linux/preempt.h:81,
from ./include/linux/spinlock.h:51,
from ./include/linux/mmzone.h:8,
from ./include/linux/bootmem.h:8,
from arch/mips/bcm63xx/prom.c:10:
arch/mips/bcm63xx/prom.c: In function 'prom_init':
./arch/mips/include/asm/string.h:162:11: error: '__builtin_memcpy' forming offset [2, 32] is out of the bounds [0, 1] of object 'bmips_smp_movevec' with type 'char' [-Werror=array-bounds]
__ret = __builtin_memcpy((dst), (src), __len); \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/mips/bcm63xx/prom.c:97:3: note: in expansion of macro 'memcpy'
memcpy((void *)0xa0000200, &bmips_smp_movevec, 0x20);
^~~~~~
In file included from arch/mips/bcm63xx/prom.c:14:
./arch/mips/include/asm/bmips.h:80:13: note: 'bmips_smp_movevec' declared here
extern char bmips_smp_movevec;
Fixes: 18a1eef92d ("MIPS: BMIPS: Introduce bmips.h")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
On some MIPS variants (e.g. MIPS r1), vDSO clock_mode is set to
VDSO_CLOCK_NONE.
When VDSO_CLOCK_NONE is set the expected kernel behavior is to fallback
on syscalls. To do that the generic vDSO library expects UULONG_MAX as
return value of __arch_get_hw_counter().
Fix __arch_get_hw_counter() on MIPS defining a __VDSO_USE_SYSCALL case
that addressed the described scenario.
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: linux-mips@vger.kernel.org
Here are a lot of small USB driver fixes for 5.4-rc3.
syzbot has stepped up its testing of the USB driver stack, now able to
trigger fun race conditions between disconnect and probe functions.
Because of that we have a lot of fixes in here from Johan and others
fixing these reported issues that have been around since almost all
time.
We also are just deleting the rio500 driver, making all of the syzbot
bugs found in it moot as it turns out no one has been using it for years
as there is a userspace version that is being used instead.
There are also a number of other small fixes in here, all resolving
reported issues or regressions.
All have been in linux-next without any reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXaH78w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk7mACgygFyLQ6GRUTTnGDcohZu44cuMO4AnR/MTrRq
/jiXPRUMsltMV7DHcq+S
=QX4p
-----END PGP SIGNATURE-----
Merge tag 'usb-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a lot of small USB driver fixes for 5.4-rc3.
syzbot has stepped up its testing of the USB driver stack, now able to
trigger fun race conditions between disconnect and probe functions.
Because of that we have a lot of fixes in here from Johan and others
fixing these reported issues that have been around since almost all
time.
We also are just deleting the rio500 driver, making all of the syzbot
bugs found in it moot as it turns out no one has been using it for
years as there is a userspace version that is being used instead.
There are also a number of other small fixes in here, all resolving
reported issues or regressions.
All have been in linux-next without any reported issues"
* tag 'usb-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (65 commits)
USB: yurex: fix NULL-derefs on disconnect
USB: iowarrior: use pr_err()
USB: iowarrior: drop redundant iowarrior mutex
USB: iowarrior: drop redundant disconnect mutex
USB: iowarrior: fix use-after-free after driver unbind
USB: iowarrior: fix use-after-free on release
USB: iowarrior: fix use-after-free on disconnect
USB: chaoskey: fix use-after-free on release
USB: adutux: fix use-after-free on release
USB: ldusb: fix NULL-derefs on driver unbind
USB: legousbtower: fix use-after-free on release
usb: cdns3: Fix for incorrect DMA mask.
usb: cdns3: fix cdns3_core_init_role()
usb: cdns3: gadget: Fix full-speed mode
USB: usb-skeleton: drop redundant in-urb check
USB: usb-skeleton: fix use-after-free after driver unbind
USB: usb-skeleton: fix NULL-deref on disconnect
usb:cdns3: Fix for CV CH9 running with g_zero driver.
usb: dwc3: Remove dev_err() on platform_get_irq() failure
usb: dwc3: Switch to platform_get_irq_byname_optional()
...
GCC 9.x automatically enables support for Loongson MMI instructions when
using some -march= flags, and then errors out when -msoft-float is
specified with:
cc1: error: ‘-mloongson-mmi’ must be used with ‘-mhard-float’
The kernel shouldn't be using these MMI instructions anyway, just as it
doesn't use floating point instructions. Explicitly disable them in
order to fix the build with GCC 9.x.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 3702bba5eb ("MIPS: Loongson: Add GCC 4.4 support for Loongson2E")
Fixes: 6f7a251a25 ("MIPS: Loongson: Add basic Loongson 2F support")
Fixes: 5188129b8c ("MIPS: Loongson-3: Improve -march option and move it to Platform")
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: stable@vger.kernel.org # v2.6.32+
Cc: linux-mips@vger.kernel.org
A Golang developer reported MIPS hwcap isn't reflecting instructions
that the processor actually supported so programs can't apply optimized
code at runtime.
Thus we export the ASEs that can be used in userspace programs.
Reported-by: Meng Zhuo <mengzhuo1203@gmail.com>
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-mips@vger.kernel.org
Cc: Paul Burton <paul.burton@mips.com>
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Paul Burton <paul.burton@mips.com>
Use ARRAY_SIZE to caluculate the top of the o32 stack.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Commit ac7c3e4ff4 ("compiler: enable CONFIG_OPTIMIZE_INLINING
forcibly") allows compiler to uninline functions marked as 'inline'.
In cace of __xchg this would cause to reference function
__xchg_called_with_bad_pointer, which is an error case
for catching bugs and will not happen for correct code, if
__xchg is inlined.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Commit ac7c3e4ff4 ("compiler: enable CONFIG_OPTIMIZE_INLINING
forcibly") allows compiler to uninline functions marked as 'inline'.
In cace of cmpxchg this would cause to reference function
__cmpxchg_called_with_bad_pointer, which is a error case
for catching bugs and will not happen for correct code, if
__cmpxchg is inlined.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
[paul.burton@mips.com: s/__cmpxchd/__cmpxchg in subject]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
The addr variable in prom_free_prom_memory() has been unused since
commit 0df1007677 ("MIPS: fw: Record prom memory"), leading to a
compiler warning:
arch/mips/fw/arc/memory.c:163:16:
warning: unused variable 'addr' [-Wunused-variable]
Fix this by removing the unused variable.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 0df1007677 ("MIPS: fw: Record prom memory")
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-mips@vger.kernel.org
The Rio500 kernel driver has not been used by Rio500 owners since 2001
not long after the rio500 project added support for a user-space USB stack
through the very first versions of usbdevfs and then libusb.
Support for the kernel driver was removed from the upstream utilities
in 2008:
943f624ab7
Cc: Cesar Miquel <miquel@df.uba.ar>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/6251c17584d220472ce882a3d9c199c401a51a71.camel@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The addr variable in prom_free_prom_memory() has been unused since
commit b3c948e2c0 ("MIPS: msp: Record prom memory"), causing a warning
& build failure due to -Werror. Remove the unused variable.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b3c948e2c0 ("MIPS: msp: Record prom memory")
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-mips@vger.kernel.org
Hauke Mehrtens