Add PHY driver for the internal USB OTG PHY found on NXP
LPC18xx and LPC43xx devices. This driver takes care of
enabling the PHY in CREG (syscon) and setting the required
clock frequency.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Add PHY driver for the Marvell HSIC 28nm PHY. This PHY is found in PXA1928
SOC.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add driver for USB 28nm PHY found in Marvell PXA1928 SOC.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
*) new Broadcom SATA3 PHY driver for Broadcom STB SoCs
*) new phy API to get PHY by index which is used in EHCI and
OHCI controller drivers
*) support specifying supply at port level used for multi-port PHYs
*) sparse warning fixes in miphy PHYs
*) fix pm_runtime issues in twl4030 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPk6
-----END PGP SIGNATURE-----
Merge tag 'phy-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.2 merge window
*) new Broadcom SATA3 PHY driver for Broadcom STB SoCs
*) new phy API to get PHY by index which is used in EHCI and
OHCI controller drivers
*) support specifying supply at port level used for multi-port PHYs
*) sparse warning fixes in miphy PHYs
*) fix pm_runtime issues in twl4030 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Supports up to two ports which can each be powered on/off and configured
independently.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
TUSB1210 ULPI PHY has vendor specific register for eye
diagram tuning. On some platforms the system firmware has
set optimized value to it. In order to not loose the
optimized value, the driver stores it during probe and
restores it every time the PHY is powered back on.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Unlike previous Allwinner SoCs, there is no central PHY control block
on the A80. Also, OTG support is completely split off into a different
controller.
This adds a new driver to support the regular USB PHYs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a minimal driver for dm816x USB. This makes USB work on dm816x
without any other changes needed as it can use the existing musb_dsps
glue layer for the USB controller.
Note that this phy is different from dm814x and am335x.
Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtrcACgkQMUfUDdst+yn0tACgygJPNvu1l3ukNJCCpWuOErIj
3KsAnjiEXv90DLYJiVLJ4EbLPw0V9wAv
=DrJx
-----END PGP SIGNATURE-----
Merge tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (299 commits)
usb: musb: fix device hotplug behind hub
usb: dwc2: Fix a bug in reading the endpoint directions from reg.
staging: emxx_udc: fix the build error
usb: Retry port status check on resume to work around RH bugs
Revert "usb: Reset USB-3 devices on USB-3 link bounce"
uhci-hub: use HUB_CHAR_*
usb: kconfig: replace PPC_OF with PPC
ehci-pci: disable for Intel MID platforms (update)
usb: gadget: Kconfig: use bool instead of boolean
usb: musb: blackfin: remove incorrect __exit_p()
USB: fix use-after-free bug in usb_hcd_unlink_urb()
ehci-pci: disable for Intel MID platforms
usb: host: pci_quirks: joing string literals
USB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)
USB: usbfs: allow URBs to be reaped after disconnection
cdc-acm: kill unnecessary messages
cdc-acm: add sanity checks
usb: phy: phy-generic: Fix USB PHY gpio reset
usb: dwc2: fix USB core dependencies
usb: renesas_usbhs: fix NULL pointer dereference in dma_release_channel()
...
This patch to add a generic PHY driver for ROCKCHIP usb PHYs,
currently this driver can support RK3288. The RK3288 SoC have
three independent USB PHY IPs which are all configured through a
set of registers located in the GRF (general register files)
module.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This change adds a support for a 14nm qcom-ufs phy that is
required in platforms that use ufs-qcom controller.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This change adds a support for a 20nm qcom-ufs phy that is required in
platforms that use ufs-qcom controller.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This change adds a generic and common API support for ufs phy QUALCOMM
Technologies. This support provides common code and also points
to specific phy callbacks to differentiate between different behaviors
of frequent use-cases (like power on, power off, phy calibration etc).
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The Armada 375 SoC comes with an USB2 host and device controller and
an USB3 controller. The USB cluster control register allows to manage
common features of both USB controllers.
This commit adds a driver integrated in the generic PHY framework to
control this USB cluster feature.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[ kishon@ti.com : Made it to use the updated devm_phy_create API and
soem cosmentic changes in Kconfig file.]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Add the driver driving the Marvell Berlin USB PHY. This allows to
initialize the PHY and to use it from the USB driver later.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The MiPHY28lp is a Generic PHY which can serve various SATA or PCIe
or USB3 devices.
Signed-off-by: alexandre torgue <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This driver adds support for USB (1.1 and 2.0) phy for STiH415 and
STiH416 System-On-Chips from STMicroelectronics.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is the generic phy driver for the picoPHY ports used by the
USB2 and USB3 Host controllers when controlling usb2/1.1 devices. It
is found on STiH407 SoC family from STMicroelectronics.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This PHY, though formally being a part of Renesas USBHS controller, contains the
UGCTRL2 register that controls multiplexing of the USB ports (Renesas calls them
channels) to the different USB controllers: channel 0 can be connected to either
PCI EHCI/OHCI or USBHS controllers, channel 2 can be connected to PCI EHCI/OHCI
or xHCI controllers.
This is a new driver for this USB PHY currently already supported under drivers/
usb/phy/. The reason for writing the new driver was the requirement that the
multiplexing of USB channels to the controller be dynamic, depending on what
USB drivers are loaded, rather than static as provided by the old driver. The
infrastructure provided by drivers/phy/phy-core.c seems to fit that purpose
ideally. The new driver only supports device tree probing for now.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
A handful of driver-related changes. We've had a bunch of them going in through
other branches as well, so it's only a part of what we really have this release.
Larger pieces are:
* Removal of a now unused PWM driver for atmel
- This includes AVR32 changes that have been appropriately acked.
* Performance counter support for the arm CCN interconnect
* OMAP mailbox driver cleanups and consolidation
* PCI and SATA PHY drivers for SPEAr 13xx platforms
* Redefinition (with backwards compatibility!) of PCI DT bindings for Tegra to
better model regulators/power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJT5DrJAAoJEIwa5zzehBx3wkkP/iwEfEK5mMon9KEe4DcKTKNq
Z6xyWuMQNHKdfBFpABs6AsHQCKDc7KK6gN3+2zLLHEJ4XGDPZ2g2NaX3oRPJlaay
BDK7rQfIZyi4tmbOnlEv1BDTYgirYBPMwk9RyNo/04Ug3W+Y67aSVo44zkNFBWaJ
GbcX/zYsrsfvdawuQMW6V/A835s3Kq5Zhv1ikPr8gDDjswZRBAT6i7FYpBSHQ8K8
bH6C1891Xit6rxXSLXJyrtM8CAet7PtLTqNr/IKdUaJnGD+fJm5EonxW+g8gvhN8
gOEkm3nM60++kdDlzZCQVNr0m1+ih6NNCr6bDLO6rIRpAJM2O+YrN1rWuZaJOu1A
pIvifk+wWHT+o52pXk8g9fK4n/ZJydK3IBzDePHMrIROOEiW5tLE3WA+u3NSfMfH
WegMt9E2dcB+5gXPeejZ9gFbAHnh2S1oVTZfCYXtuOHrYiEU9U0FA3eRYvJEE2po
k8sdiOn7Vc65O1QZ+xZNbLABpAHaye7X2evOJyhSutzHE/AtUvT4vuCAZ0tggXyD
E1qVKngVW/NvcoFbwYeidq4bOVgiAEn3idZgF5gEq1mq7LzetXUQAcZAOQfLWHLQ
RrXufS7Ez8pSCG74y0AFReVfQH2PgWHPqGUGj99NXgQauexc/vR1Hc5Iqb8liGNJ
n6i8RqvvQ4KYcmHEXDIT
=fsP6
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"A handful of driver-related changes. We've had a bunch of them going
in through other branches as well, so it's only a part of what we
really have this release.
Larger pieces are:
- Removal of a now unused PWM driver for atmel
[ This includes AVR32 changes that have been appropriately acked ]
- Performance counter support for the arm CCN interconnect
- OMAP mailbox driver cleanups and consolidation
- PCI and SATA PHY drivers for SPEAr 13xx platforms
- Redefinition (with backwards compatibility!) of PCI DT bindings for
Tegra to better model regulators/power"
Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.
Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.
* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: arm-ccn: Fix error handling at event allocation
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
bus: ARM CCN: add PERF_EVENTS dependency
bus: ARM CCN PMU driver
PCI: spear: Remove spear13xx_pcie_remove()
PCI: spear: Fix Section mismatch compilation warning for probe()
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: SPEAr13xx: Update defconfigs
ARM: SPEAr13xx: Add pcie and miphy DT nodes
ARM: SPEAr13xx: Add bindings and dt node for misc block
ARM: SPEAr13xx: Fix static mapping table
phy: Add drivers for PCIe and SATA phy on SPEAr13xx
...
This is the bulk of new SoC enablement and other platform changes for 3.17:
* Samsung S5PV210 has been converted to DT and multiplatform
* Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms
* Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood.
* Hwmod data for TI AM43xx and DRA7 platforms.
* More additions of Renesas shmobile platform support
* Removal of plat-samsung contents that can be removed with S5PV210 being
multiplatform/DT-enabled and the other two old platforms being removed.
New platforms (most with only basic support right now):
* Hisilicon X5HD2 settop box chipset is introduced
* Mediatek MT6589 (mobile chipset) is introduced
* Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=5TJ6
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This is the bulk of new SoC enablement and other platform changes for
3.17:
- Samsung S5PV210 has been converted to DT and multiplatform
- Clock drivers and bindings for some of the lower-end i.MX 1/2
platforms
- Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood
- Hwmod data for TI AM43xx and DRA7 platforms
- More additions of Renesas shmobile platform support
- Removal of plat-samsung contents that can be removed with S5PV210
being multiplatform/DT-enabled and the other two old platforms
being removed
New platforms (most with only basic support right now):
- Hisilicon X5HD2 settop box chipset is introduced
- Mediatek MT6589 (mobile chipset) is introduced
- Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code"
* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
ARM: hisi: remove smp from machine descriptor
power: reset: move hisilicon reboot code
ARM: dts: Add hix5hd2-dkb dts file.
ARM: debug: Rename Hi3716 to HIX5HD2
ARM: hisi: enable hix5hd2 SoC
ARM: hisi: add ARCH_HISI
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Documentation: arm: misc updates to Marvell EBU SoC status
Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
ARM: mvebu: fix build without platforms selected
ARM: mvebu: add cpuidle support for Armada 38x
ARM: mvebu: add cpuidle support for Armada 370
cpuidle: mvebu: add Armada 38x support
cpuidle: mvebu: add Armada 370 support
cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
ARM: mvebu: export the SCU address
...
The MiPHY365x is a Generic PHY which can serve various SATA or PCIe
devices. It has 2 ports which it can use for either; both SATA, both
PCIe or one of each in any configuration.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a PHY driver for uses with AHCI based SATA controller driver on the
IPQ806x family of SoCs.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a PHY driver for uses with AHCI based SATA controller driver on the
APQ8064 family of SoCs.
This patch is a forward port from Qualcomm's v3.4 andriod kernel.
Tested on IFC6410 board.
CC: Sujit Reddy Thumma <sthumma@codeaurora.org>
Tested-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the Samsung's S5PV210 SoC to the Exynos USB 2.0 PHY driver.
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
[k.debski@samsung.com: cleanup and commit description]
[k.debski@samsung.com: make changes accordingly to the mailing list
comments]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM based ST Microelectronics's SPEAr1310/40 platforms uses ST's phy (known as
'miphy') for PCIe and SATA. This patch adds drivers for these miphys.
This also adds proper bindings for miphys.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
[viresh: fixed logs/cclist/checkpatch warnings, broken into smaller patches]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
The new driver uses the generic PHY framework and will interact
with DWC3 controller present on Exynos5 series of SoCs.
Also, created a new header file in linux/mfd/syscon/ for
Exynos5 SoCs and put the required PMU offset definitions
for the basic available PHYs.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The top-level phy-samsung-usb2 driver may be configured as a
loadable module, which currently causes link errors because
of the dependency on the exynos{5250,4x12,4210}_usb2_phy_config
symbol. Solving this could be achieved by exporting these
symbols, but as the SoC-specific parts of the driver are not
currently built as modules, it seems better to just link
everything into one module and avoid the need for the export.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the APM X-Gene SoC 15Gbps Multi-purpose PHY.
This is the physical layer interface for the corresponding host
controller. Currently, only external clock and Gen3 SATA mode
are supported.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Tuan Phan <tphan@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Rename struct omap_control_usb to struct omap_control_phy since it can
be used to control PHY of USB, SATA and PCIE. Also move the driver and
include files under *phy* and made the corresponding changes in the users
of phy-omap-control.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Add support for Exynos 5250. This driver is to replace the old
USB 2.0 PHY driver.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a new driver for the Exynos USB 2.0 PHY. The new driver uses the generic
PHY framework. The driver includes support for the Exynos 4x10 and 4x12
SoC families.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adapted omap-usb3 PHY driver to Generic PHY Framework and moved phy-omap-usb3
driver in drivers/usb/phy to drivers/phy and also renamed the file to
phy-ti-pipe3 since this same driver will be used for SATA PHY and
PCIE PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Allwinner A1x / A2x SoCs have 2 or 3 usb phys which are all accessed
through a single set of registers. Besides this there are also some other
phy related bits which need poking, which are per phy, but shared between the
ohci and ehci controllers, so these are also controlled from this new phy
driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds the SATA PHY driver for Exynos5250.This driver uses the
generic PHY framework to deal with SATA PHY.Exynos5250 SATA PHY comprises
of CMU and TRSV blocks which are of I2C register Map.So this driver
configures the CMU and TRSV block of exynos5250 SATA PHY using i2c.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here's the big USB pull request for 3.14-rc1
Lots of little things all over the place, and the usual USB gadget
updates, and XHCI fixes (some for an issue reported by a lot of people.)
USB PHY updates as well as chipidea updates and fixes.
All of these have been in the linux-next tree with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdjwIACgkQMUfUDdst+ylBIQCgkRoR8lJc0L5lZ3fugIJL4IzZ
j6AAn0nBLP6VI0cvUEi3TcrPTzv4MEuL
=Yb+I
-----END PGP SIGNATURE-----
Merge tag 'usb-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB pull request for 3.14-rc1
Lots of little things all over the place, and the usual USB gadget
updates, and XHCI fixes (some for an issue reported by a lot of
people). USB PHY updates as well as chipidea updates and fixes.
All of these have been in the linux-next tree with no reported issues"
* tag 'usb-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (318 commits)
usb: chipidea: udc: using MultO at TD as real mult value for ISO-TX
usb: chipidea: need to mask INT_STATUS when write otgsc
usb: chipidea: put hw_phymode_configure before ci_usb_phy_init
usb: chipidea: Fix Internal error: : 808 [#1] ARM related to STS flag
usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28
usb: chipidea: add freescale imx28 special write register method
usb: ehci: add freescale imx28 special write register method
usb: core: check for valid id_table when using the RefId feature
usb: cdc-wdm: resp_count can be 0 even if WDM_READ is set
usb: core: bail out if user gives an unknown RefId when using new_id
usb: core: allow a reference device for new_id
usb: core: add sanity checks when using bInterfaceClass with new_id
USB: image: correct spelling mistake in comment
USB: c67x00: correct spelling mistakes in comments
usb: delete non-required instances of include <linux/init.h>
usb:hub set hub->change_bits when over-current happens
Revert "usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28"
xhci: Set scatter-gather limit to avoid failed block writes.
xhci: Avoid infinite loop when sg urb requires too many trbs
usb: gadget: remove unused variable in gr_queue_int()
...
Kirkwood and Dove can turn the SATA phy on and off. Add a PHY driver
to control this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a driver for the internal Broadcom Kona USB 2.0 PHY found
on the BCM281xx family of SoCs.
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a PHY provider driver for the Samsung Exynos SoC Display Port PHY.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Used the generic PHY framework API to create the PHY. For powering on
and powering off the PHY, power_on and power_off ops are used. Once the
MUSB OMAP glue is adapted to the new framework, the suspend and resume
ops of usb phy library will be removed. Also twl4030-usb driver is moved
to drivers/phy/.
However using the old usb phy library cannot be completely removed
because otg is intertwined with phy and moving to the new
framework completely will break otg. Once we have a separate otg state machine,
we can get rid of the usb phy library.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Used the generic PHY framework API to create the PHY. Now the power off and
power on are done in omap_usb_power_off and omap_usb_power_on respectively.
The omap-usb2 driver is also moved to driver/phy.
However using the old USB PHY library cannot be completely removed
because OTG is intertwined with PHY and moving to the new framework
will break OTG. Once we have a separate OTG state machine, we
can get rid of the USB PHY library.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PHY framework provides a set of APIs for the PHY drivers to
create/destroy a PHY and APIs for the PHY users to obtain a reference to the
PHY with or without using phandle. For dt-boot, the PHY drivers should
also register *PHY provider* with the framework.
PHY drivers should create the PHY by passing id and ops like init, exit,
power_on and power_off. This framework is also pm runtime enabled.
The documentation for the generic PHY framework is added in
Documentation/phy.txt and the documentation for dt binding can be found at
Documentation/devicetree/bindings/phy/phy-bindings.txt
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>