Separate the old imx7d-pico into cpu (imx7d-pico.dtsi) and baseboard
(imx7d-pico-pi.dts) dts so the same cpu dtsi can be used in different
baseboards variants.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Cubox-i and Hummingboard variants for v1.5 SOMs, where the SOM has
eMMC fitted.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Cubox-i and Hummingboard variants for v1.5 SOMs, which have TI
Wi-Fi instead of Broadcom Wi-Fi. This variant does not include
SOM eMMC support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We add device tree files for a couple of additional SoCs in various areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for networking,
Amlogic A113D for audio, and Renesas R-Car V3M for automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX, Amlogic
and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues that
the latest version of 'dtc' now warns about. Unfortunately there is still
a lot left to do.
A rework of the ARM foundation model introduced several new files
for common variations of the model.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TnSo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional SoCs in various
areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for
networking, Amlogic A113D for audio, and Renesas R-Car V3M for
automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX,
Amlogic and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues
that the latest version of 'dtc' now warns about. Unfortunately there
is still a lot left to do.
A rework of the ARM foundation model introduced several new files for
common variations of the model"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits)
arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3
dt-bindings: bus: Add documentation for the Technologic Systems NBUS
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
...
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----
iQItBAABCAAXBQJaCwaSEBxyb2JoQGtlcm5lbC5vcmcACgkQ+vtdtY28YcNzeA/8
C8uQhSsX2+UQZvFzcEA8KQAMGT3kYdrcf+gidRKwCEUWg1qscUEpTb3n3Rm5NUbU
RPD1s6GSlh6fJCMHDTQ6Tti/T59L7nZa2/AIGmUishGu4x4q1o18AobpFJmYP/EM
SJPwnmm5RV9WcZFao1y+sY3Xtn8DStxHO4cS+dyF5/EvPN9D8nbLJfu7bgTBAZww
HktIMB9kx+GTipRQZBvBwXoy5MJjthIZub4XwzesA4tGananj4cXlc0xaVxpdYy3
5bO6q5F7cbrZ2uyrF+oIChpCENK4VaXh80m0WHc8EzaG++shzEkR4he1vYkwnV+I
OYo4vsUg9dP8rBksUG1eYhS8fJKPvEBRNP7ETT5utVBy5I/tDEbo/crmQZRTIDIC
hZbhcdZlISZj0DzkMK2ZHQV9UYtRWzXrJbZHFIPP12GCyvXVxYJUIWb9iYnUYSon
KugygsFSpZHMWmfAhemw5/ctJZ19qhM5UIl2KZk5tMBHAf466ILmZjg0me6fYkOp
eADfwHJ1dLMdK79CVMHSfp+vArcZXp35B16c3sWpJB36Il97Mc/9siEufCL4GKX7
IBBnQBlbpSBKBejWVyI7Ip/Xp5u4qAQD+ZMJ9oLqBRqfWerHbDuOERlEOgwGqJYr
9v4HvP7V8eVUvAdqXka4EBfCyAgUzXDAxG2Dfmv9vGU=
=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.
Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.
One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.
Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.
As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>
We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.
Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
This updates the Guitar board DT with a clock node for the debug UART
and adds a new DT for the CubieBoard6.
It also updates the S500 DT with CPU power domains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJZ/ZWMAAoJEPou0S0+fgE/fHcQAIdbR8x3BqQ208lnaCAPHGDT
jAkpW1FrnuxO+94r1eKMqOQjZ9Eh5t4qq1MmWSXQaNn7UGaLkYBKIb7T6A+O2H3X
/cNgjU58DWqOgkp3M6TGbRK1WAlEncQWSGCiVAPwqe+dJvvi7PXnxSBz0zCdh2z6
y01TrmswsapjnOBhfaXJmMvTg1yDEaC7uo3tNNo+9fLRs3kvRv8MeONgQ08/JFOc
jLR5WL6Abs+sl/YWMOljFG4M/koUKz/xgPaA0IiQTtd2+sLfkEWivjWNmyDxqm09
k04bCW+w4ZBV8P7OYH7fpeQ0f77jILQl/v/3VdSAQ3+gB2jSCLWgHUKzgvg1r/Qr
XafaTPQbKySRUimufOlIMzEJVo/tz3oXahkvcDVw6q0CYFC7R0ohLHKCho2uon7l
ZiDgGsVwJ/PY0luXf32oIV5EvcMBzgj6MQzqk1f1L6v9g/ZGc+0G/cC0VERcwqRX
tZZrnHiVRD7ICRwAeV6hKmyUhb6wD+KhC92U20O1qQwcsD7mwdDIXjPqAQedva6D
B/tAIZIBfATlfANNfs6Wk4YXS1S5fbGU3oM5aLFnvvadBDOgxbQYjkpBD03ST+Lf
Nji2F/YpAGfBnHvZDOcoGl3yJ4sPbsTVDmgkjUZT37nLKYnnBqAqBgb1cXlq7eoP
djOJEUb5X202cCWRnP8c
=Bu/n
-----END PGP SIGNATURE-----
Merge tag 'actions-arm-dt-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions into next/dt
Pull "Actions Semi ARM based SoC DT for v4.15" from Andreas Färber:
This updates the Guitar board DT with a clock node for the debug UART
and adds a new DT for the CubieBoard6.
It also updates the S500 DT with CPU power domains.
* tag 'actions-arm-dt-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- New board support: i.MX51 ZII RDU1, i.MX53 GE Healthcare PPD, i.MX6
TX modules for MB7 from Ka-Ro Electronics, i.MX6 Wandboard revd1
variants, i.MX6 LWN DISPLAY5 board, Pistachio i.MX6Q board, i.MX6SX
Vining-2000 board.
- Use the 'vpcie-supply' property for PCIe device for boards
imx6qdl-sabresd, imx6q-novena and imx6q-cm-fx6.
- A series from Jagan Teki to update imx6qdl-icore board with audio,
touch and CAN support.
- Switch to nvmem for accessing OCOTP from tempmon for i.MX6SX and add
tempmon support for i.MX6UL.
- A bunch of patches from Lothar Waßmann updating Ka-Ro i.MX28, i.MX53
and i.MX6 TX modules.
- Fix DTC warnings in i.MX device trees, dropping leading zeros from
unit address, correcting display nodes notation and display port
names, fixing nodes with unit name and no reg property.
- Other random device updates for various board support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ7ypUAAoJEFBXWFqHsHzOpVkH/RsZ3IMg8O5tMO6uz1CNmutR
3EAXfBeQTnQZe2A/3XkDRpJWGiIniRSVAf6rYipmeyV9jV2Ff4vfiv5gnhg1ev+B
eV35W3gb3EclHKrHgHVMkfzWfNp63L1etdVFrY0QuMc0wQbch0TwO3TTPHpk0+AS
eauLOMY1qzRVnayzZ8IeTn++igsoj4KT1NmIprNKe66eDAOfWxO0IB26r0svKrhg
mIlqTUG1p6I/H8h6hQZuRJaLM9no3dHDcm7Scbf1y8Mvf5mPVTTHKXGLLyEVT/UB
SEWydfAt0VEAEA+Uk6pFJsrG1KRx0hwF46DHk2BXj7A1wxBsUIPnMSoMRWgGrZE=
=grKK
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree updates for 4.15" from Shawn Guo:
- New board support: i.MX51 ZII RDU1, i.MX53 GE Healthcare PPD, i.MX6
TX modules for MB7 from Ka-Ro Electronics, i.MX6 Wandboard revd1
variants, i.MX6 LWN DISPLAY5 board, Pistachio i.MX6Q board, i.MX6SX
Vining-2000 board.
- Use the 'vpcie-supply' property for PCIe device for boards
imx6qdl-sabresd, imx6q-novena and imx6q-cm-fx6.
- A series from Jagan Teki to update imx6qdl-icore board with audio,
touch and CAN support.
- Switch to nvmem for accessing OCOTP from tempmon for i.MX6SX and add
tempmon support for i.MX6UL.
- A bunch of patches from Lothar Waßmann updating Ka-Ro i.MX28, i.MX53
and i.MX6 TX modules.
- Fix DTC warnings in i.MX device trees, dropping leading zeros from
unit address, correcting display nodes notation and display port
names, fixing nodes with unit name and no reg property.
- Other random device updates for various board support.
* tag 'imx-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (63 commits)
ARM: dts: imx53-tx53: fix interrupt flags
ARM: dts: imx28-tx28: fix interrupt flags
ARM: dts: display5: Device tree description of LWN's DISPLAY5 board
ARM: dts: imx53-qsb-common: Fix 'led_gpio7_7@0' node with unit name and no reg property
ARM: dts: imx53-m53evk: Fix 'led_gpio@0' node with unit name and no reg property
ARM: dts: imx53: Fix 'usbphy@x' node with unit name and no reg property
ARM: dts: imx51-ts4800: Fix 'port@0' node with unit name and no reg property
ARM: dts: imx51-apf51dev: Fix 'backlight@bl1' node with unit name and no reg property
ARM: dts: imx: add ZII RDU1 board
ARM: dts: imx: add support for TX6 modules on MB7 baseboard
ARM: dts: imx: add support for TX6QP
ARM: dts: imx6-tx6: add a .dtsi file for the MB7 baseboard
ARM: dts: imx6-tx6: move display configuration to .dtsi file
ARM: dts: imx6-tx6: add support for I2C bus recovery
ARM: dts: imx6-tx6: convert to using simple-audio-card
ARM: dts: imx6-tx6: specify ethernet phy reset post-delay
ARM: dts: imx6-tx6: improve ethernet related pinctrl setup
ARM: dts: imx6-tx6: add trickle-charge config for DS1339
ARM: dts: imx6-tx6: remove obsolete ipu1 alias
ARM: dts: imx6-tx6: remove obsolete eeti,egalax_ts
...
[arnd: made sure we have no new leading zeroes in unit address during merge]
please pull the following:
- Eric adds support for the CLCD and PWM controller on Cygnus chis
- Loic fixes the console path on the Raspberry Pi 3 (already submitted as
fixes) and then proceeds with enabling the BCM43438 bluetooth chip on
the Raspberry Pi 3
- Rafal specifies the USB ports on the Luxul XWR-1200
- Dan adds support for the Luxul ABR-4500 based on BCM47094, the Luxul XAP-810
and XAP-1440 both based on BCM53573
- Florian adds support for the Broadcom Hurricane 2 SoC by adding general
machine binding, clock binding, SoC DTS include file and a DTS for the
Ubiquiti Networks UniFi Switch 8
-----BEGIN PGP SIGNATURE-----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=DmZ2
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.15/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.15" from Florian Fainelli:
This pull request contains Broadcom ARM-based Device Tree changes for 4.15,
please pull the following:
- Eric adds support for the CLCD and PWM controller on Cygnus chis
- Loic fixes the console path on the Raspberry Pi 3 (already submitted as
fixes) and then proceeds with enabling the BCM43438 bluetooth chip on
the Raspberry Pi 3
- Rafal specifies the USB ports on the Luxul XWR-1200
- Dan adds support for the Luxul ABR-4500 based on BCM47094, the Luxul XAP-810
and XAP-1440 both based on BCM53573
- Florian adds support for the Broadcom Hurricane 2 SoC by adding general
machine binding, clock binding, SoC DTS include file and a DTS for the
Ubiquiti Networks UniFi Switch 8
* tag 'arm-soc/for-4.15/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: Hurricane 2: Add basic support for Ubiquiti UniFi Switch 8
dt-bindings: Add Ubiquiti Networks vendor prefix
ARM: dts: Add Broadcom Hurricane 2 DTS include file
dt-bindings: Document Broadcom Hurricane 2 clocks
dt-bindings: Add documentation for Broadcom Hurricane 2 SoCs
ARM: dts: BCM53573: Add DT for Luxul XAP-1440
ARM: dts: BCM53573: Add DT for Luxul XAP-810
ARM: dts: BCM5301X: Add DT for Luxul ABR-4500
ARM: dts: BCM5301X: Add DT for Luxul XBR-4500
ARM: dts: BCM5301X: Specify USB ports for USB LED of Luxul XWR-1200
ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave
ARM: dts: bcm283x: Fix console path on RPi3
ARM: dts: cygnus: Add the PWM node
ARM: dts: cygnus: Add the CLCD controller
* r8a77430 (RZ/G1M) SoC
- Add XHCI support to SoC DT. Boards may enable this as appropriate
* All Renesas ARM based SoCs
- Add missing clocks for ARM CPU cores
Geert Uytterhoeven says "This series improves DT hardware descriptions
for Renesas arm32 SoCs by adding missing clocks properties to the
device nodes corresponding to ARM CPU cores."
* R-Car Gen 1 and 2, and RZ/G SoCs
- Use R-Car Fallback compat strings for GPIO
Simon Horman says "Use newly added R-Car GPIO Gen 1, 2 and 3 fallback
compat strings in peace of now deprecated non-generation specific R-Car
GPIO fallback compat string in the DT of Renesas ARM and arm64 based
SoCs.
As noted in the changelogs for the r8a777[89] changes, this introduces
an incompatibility with pre-v4.14 kernels used with new DTBs. There is
no run-time effect for other SoCs updated by this changeset."
* r7s72100 (RZ/A1H) GR-Peach board
- Add pin configuration subnode for ETHER pin group.
This avoids relying on boot-loader configuration of these pins.
- Enable ostm0 and ostm1 timers
Jacopo Mondi says these are "to be used as clock source and clockevent
source. The timers provides greater accuracy than the already enabled
mtu2 one."
- Correct leds node name indent
- Enable MTU2 timer pulse unit
Jacopo Mondi says "MTU2 multi-function/multi-channel timer/counter is
not enabled for GR-Peach board. The timer is used as clock event source
to schedule wake-ups, and without this enabled all sleeps not performed
through busy waiting hang the board."
* r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven SoM
- Add USB function support
* r8a7745 (RZ/G1E) iW-RainboW-G22D development platform
- Add USB2.0 Host support
* r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven development platform
- Rework DT architecture and add DT for camera DB
Fabrizio Castro says "Some of the serial interfaces are exposed on the
camera daughter board. The camera daughter board can be connected to
the carrier board by means of expansion connectors 1, 2 and 3. The
carrier board may host an RZ/G1M or an RZ/G1N based SoM.
While adding support for the serial interfaces on the camera daughter
board we faced the dilemma of how to properly describe all of the
possible HW configurations and how to maximize code reuse.
The best option would be to use device tree overlays, however there is
still some work to be done on that front before actually using them,
therefore for the time being we decided to provide .dtsi files to
describe the carrier board and the camera daughter board, and provide
.dts files to describe the HW configurations we need to support."
* r8a779[0-4] R-Car Gen2 SoCs
- Use generic node name for VSP1 nodes
Geert Uytterhoeven says "This patch series replaces the specific node
names used for the VSP1 nodes by the preferred generic node names, cfr.
commit 0e1bfb72b0 ("v4l: vsp1: Use generic node name")."
-----BEGIN PGP SIGNATURE-----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=Y3FX
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Second Round of Renesas ARM Based SoC DT Updates for v4.15" from Simon Horman:
* r8a77430 (RZ/G1M) SoC
- Add XHCI support to SoC DT. Boards may enable this as appropriate
* All Renesas ARM based SoCs
- Add missing clocks for ARM CPU cores
Geert Uytterhoeven says "This series improves DT hardware descriptions
for Renesas arm32 SoCs by adding missing clocks properties to the
device nodes corresponding to ARM CPU cores."
* R-Car Gen 1 and 2, and RZ/G SoCs
- Use R-Car Fallback compat strings for GPIO
Simon Horman says "Use newly added R-Car GPIO Gen 1, 2 and 3 fallback
compat strings in peace of now deprecated non-generation specific R-Car
GPIO fallback compat string in the DT of Renesas ARM and arm64 based
SoCs.
As noted in the changelogs for the r8a777[89] changes, this introduces
an incompatibility with pre-v4.14 kernels used with new DTBs. There is
no run-time effect for other SoCs updated by this changeset."
* r7s72100 (RZ/A1H) GR-Peach board
- Add pin configuration subnode for ETHER pin group.
This avoids relying on boot-loader configuration of these pins.
- Enable ostm0 and ostm1 timers
Jacopo Mondi says these are "to be used as clock source and clockevent
source. The timers provides greater accuracy than the already enabled
mtu2 one."
- Correct leds node name indent
- Enable MTU2 timer pulse unit
Jacopo Mondi says "MTU2 multi-function/multi-channel timer/counter is
not enabled for GR-Peach board. The timer is used as clock event source
to schedule wake-ups, and without this enabled all sleeps not performed
through busy waiting hang the board."
* r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven SoM
- Add USB function support
* r8a7745 (RZ/G1E) iW-RainboW-G22D development platform
- Add USB2.0 Host support
* r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven development platform
- Rework DT architecture and add DT for camera DB
Fabrizio Castro says "Some of the serial interfaces are exposed on the
camera daughter board. The camera daughter board can be connected to
the carrier board by means of expansion connectors 1, 2 and 3. The
carrier board may host an RZ/G1M or an RZ/G1N based SoM.
While adding support for the serial interfaces on the camera daughter
board we faced the dilemma of how to properly describe all of the
possible HW configurations and how to maximize code reuse.
The best option would be to use device tree overlays, however there is
still some work to be done on that front before actually using them,
therefore for the time being we decided to provide .dtsi files to
describe the carrier board and the camera daughter board, and provide
.dts files to describe the HW configurations we need to support."
* r8a779[0-4] R-Car Gen2 SoCs
- Use generic node name for VSP1 nodes
Geert Uytterhoeven says "This patch series replaces the specific node
names used for the VSP1 nodes by the preferred generic node names, cfr.
commit 0e1bfb72b0 ("v4l: vsp1: Use generic node name")."
* tag 'renesas-dt2-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (42 commits)
ARM: dts: r8a7743: Add xhci support to SoC dtsi
ARM: dts: r7s72100: Add clock for CA9 CPU core
dt-bindings: clk: r7s72100: Add missing I and G clocks
ARM: dts: sh73a0: Add clocks for CA9 CPU cores
ARM: dts: r8a7794: Add missing clock for secondary CA7 CPU core
ARM: dts: r8a7793: Add missing clock for secondary CA15 CPU core
ARM: dts: r8a7792: Add missing clock for secondary CA15 CPU core
ARM: dts: r8a7791: Add missing clock for secondary CA15 CPU core
ARM: dts: r8a7790: Add clocks for CA7 CPU cores
ARM: dts: r8a7790: Add missing clocks for secondary CA15 CPU cores
ARM: dts: r8a7779: Add clocks for CA9 CPU cores
ARM: dts: r8a7778: Add clock for CA9 CPU core
ARM: dts: r8a7743: Add missing clock for secondary CA15 CPU core
ARM: dts: r8a73a4: Add clock for CA15 CPU0 core
ARM: dts: r8a7794: Use R-Car GPIO Gen2 fallback compat string
ARM: dts: r8a7793: Use R-Car GPIO Gen2 fallback compat string
ARM: dts: r8a7792: Use R-Car GPIO Gen2 fallback compat string
ARM: dts: r8a7791: Use R-Car GPIO Gen2 fallback compat string
ARM: dts: r8a7790: Use R-Car GPIO Gen2 fallback compat string
ARM: dts: r8a7743: Use R-Car GPIO Gen2 fallback compat string
...
The most notable changes are:
- Conversion to the last SoC (A10, A20) to the new clock framework
- HDMI and dual pipeline support for the A10, A20 and A31 DRM driver
- Support for the various power supplies on a number of boards
- Fix of DTC warnings on a number of SoCs, but most of them still need
some work
- New boards: A20-OLinuXino-MICRO-eMMC, TBS A711, Banana Pi M2 Berry,
Banana Pi M2 Ultra
-----BEGIN PGP SIGNATURE-----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=HjP6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner DT changes for 4.15" from Maxime Ripard:
The most notable changes are:
- Conversion to the last SoC (A10, A20) to the new clock framework
- HDMI and dual pipeline support for the A10, A20 and A31 DRM driver
- Support for the various power supplies on a number of boards
- Fix of DTC warnings on a number of SoCs, but most of them still need
some work
- New boards: A20-OLinuXino-MICRO-eMMC, TBS A711, Banana Pi M2 Berry,
Banana Pi M2 Ultra
- New R40 SoC support
* tag 'sunxi-dt-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (63 commits)
ARM: sun8i: r40: enable USB host for Banana Pi M2 Ultra
ARM: sun8i: v40: add 5V regulator for Banana Pi M2 Berry
ARM: sun8i: r40: add 5V regulator for Banana Pi M2 Ultra
ARM: sun8i: r40: add USB host port nodes for R40
ARM: dts: sun4i: Enable HDMI support on some A10 devices
ARM: dts: sun7i: Enable HDMI support on some A20 devices
ARM: dts: sun7i: Add device nodes for display pipelines
ARM: dts: sun4i: Add device nodes for display pipelines
ARM: dts: sun8i: r40: add watchdog device node
ARM: dts: sun5i: reference-design-tablet: Enable AXP209 AC and battery
ARM: dts: sun9i: Change node names to remove underscores
ARM: dts: sun9i: Change node names to remove underscores
ARM: dts: sun4i: Remove underscores from nodes names
ARM: dts: sun4i: Provide default muxing for relevant controllers
ARM: dts: sun4i: Change pinctrl nodes to avoid warning
ARM: dts: sun6i: Enable HDMI support on some A31/A31s devices
ARM: dts: sun6i: Add device node for HDMI controller
ARM: dts: sun4i: Change LRADC node names to avoid warnings
ARM: dts: sun4i: Remove skeleton and memory to avoid warnings
ARM: dts: sun4i: Remove gpio-keys warnings
...
This adds support for the Zodiac Inflight Innovations RDU1 board,
which is based on the i.MX51.
It is the predecessor of the already supported ZII RDU2 board and
relies on the bootloader in the same way to enable correct display
and touchscreen nodes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The TX6QP-8037 is a Computer On Module manufactured by
Ka-Ro electronics GmbH with the following characteristics:
Processor Freescale i.MX 6QuadPlus MCIMX6QP7, 1 GHz
RAM 1GiB 64-bit DDR3 SDRAM
ROM 4GB HiRel eMMC
Power supply Single 3.3 to 5V
Size 26mm SO-DIMM
Temp. Range -40°C to 105°C
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Latest wandboard hardware revision is revd1, which brings the following
new features:
- PFUZE100 PMIC
- AR8035 Ethernet PHY
- Upgrade Wifi/BT chip to BCM4339/BCM43430.
Add support for the mx6, mx6dl and mx6qp revd1 variants.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull "Rockchip dts32 updates for 4.15 part1" from Heiko Stübner:
One new board the Vyasa from Amarula Solutions using a rk3288
and core lvds node for the newly added driver+binding.
Also bindings + nodes for the Mali-Utgard GPUs found on some
Rockchip socs like rk3036 and rk3188. With the recently revived
Lima project they can even render a red triangle to a png file.
* tag 'v4.15-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Enable thermal on rk3288-vyasa board
ARM: dts: rockchip: fix mali400 ppmmu interrupt names
ARM: dts: rockchip: Enable mali GPU node on rk3288-vyasa
ARM: dts: rockchip: enable gpu on rk3188-radxarock
ARM: dts: rockchip: add gpu nodes on rk3066/rk3188
ARM: dts: rockchip: add rk322x gpu node
ARM: dts: rockchip: enable the gpu on rk3036-kylin boards
ARM: dts: rockchip: add rk3036 gpu node
dt-bindings: gpu: mali-utgard: add optional power-domain reference
dt-bindings: gpu: mali-utgard: add optional supply regulator
dt-bindings: gpu: mali-utgard: Add Rockchip Utgard Malis
ARM: dts: rockchip: enable vops and hdmi output on rk3288-vyasa
ARM: dts: rockchip: Add rk3288 vyasa board
dt-bindings: Add vendor prefix for Amarula Solutions
ARM: dts: rockchip: add LVDS node for rk3288
Pull "Samsung DTS ARM changes for 4.15" from Krzysztof Kozłowski:
1. Add new board: Hardkernel Odroid HC1.
2. Fix incomplete Odroid-XU3/4 thermal-zones definition leading to
possible overheat if first pair of A7+A15 cores is idle but rest of
CPUs are busy.
3. Add capacity-dmips-mhz properties for CPUs of octa-core SoCs.
4. Add power button to Odroid XU3/4.
5. Improvements in Gscaler, HDMI and Mixer blocks on Exynos5.
6. Add suspend quirk to DWC3 USB controller to fix enumeration of
SuperSpeed devices on Odroid XU4.
7. Add HDMI and MHL to Trats2.
8. Cleanups (redundant properties and nodes).
* tag 'samsung-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: samsung: Document binding for new Odroid HC1 board
ARM: dts: exynos: Add HDMI and Sil9234 to Trats2 board
ARM: dts: exynos: Add support for Hardkernel's Odroid HC1 board
ARM: dts: exynos: Move audio clocks configuration to odroidxu3-audio.dtsi
ARM: dts: exynos: Add dwc3 SUSPHY quirk
ARM: dts: exynos: Add status property to Exynos 542x Mixer nodes
ARM: dts: exynos: Add status property to Exynos 5250 HDMI and Mixer nodes
ARM: dts: exynos: Cleanup HDMI DCC definitions on Exynos5250 and Exynos542x boards
ARM: dts: exynos: Move HDMI PHY node from boards to exynos5250.dtsi
ARM: dts: exynos: Use specific compatibles for proper Gscaler limits on Exynos5250 and Exynos5420
ARM: dts: exynos: Remove redundant interrupt properties in gpio-keys on Odroid boards
ARM: dts: exynos: Add power button for Odroid XU3/4
ARM: dts: exynos: Remove the display-timing and delay from Rinato
ARM: dts: exynos: add exynos5422 cpu capacity-dmips-mhz information
ARM: dts: exynos: add exynos5420 cpu capacity-dmips-mhz information
ARM: dts: exynos: fix incomplete Odroid-XU3/4 thermal-zones definition
Add basic board support for the Ubiquiti UniFi Switch 8 port model. This
is a small home and office use managed switch based on the BCM53342
switching control SoC.
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This DTS has support for the Fairphone 2 (codenamed FP2).
This first version of the DTS supports just the serial console via the
MSM UART pins.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds a basic DTS file for the Sony Xperia Z2 Tablet, containing
definitions for regulators, eMMC/SD-card, USB, WiFi, Touchscreen,
charger, backlight, coincell and buttons.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This is BCM53573 WiSoC based outdoor access point with an extra BCM43217
chipset used for 2.4 GHz.
Signed-off-by: Dan Haab <dhaab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This is BCM53573 WiSoC based access point with an extra BCM43217 chipset
used for 2.4 GHz.
Signed-off-by: Dan Haab <dhaab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This is BCM47094 (AKA BCM4709C0) based router with rear-facing ports
board design.
Signed-off-by: Dan Haab <dhaab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This is BCM47094 (AKA BCM4709C0) based router with ports-on-the-front
board design.
Signed-off-by: Dan Haab <dhaab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch adds a .dtsi that describes the camera daughter board
and a .dts to describe the HW made of iWave's RZ/G1M SoM, iWave's
RZ/G1M/G1N Qseven carrier board, and the camera daughter board.
The camera daughter board .dtsi adds support for ttySC[14].
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Banana Pi M2 Ultra is an SBC based on the Allwinner V40 SoC (same as
the R40 SoC). The form factor is similar to the Raspberry Pi series.
It features:
- X-Powers AXP221s PMIC connected to i2c0
- 1GiB DDR3 DRAM
- microSD slot
- MicroUSB Type-B port for power and connected to usb0
- HDMI output
- MIPI DSI connector
- 4 USB Type-A ports (connected to the usb1 controller via a hub)
- gigabit ethernet with Realtek RTL8211E transceiver
- WiFi/Bluetooth with AP6212 module, with external antenna connector
- SATA and power connectors for native SATA support
- camera sensor connector
- audio out headphone jack
- red and green LEDs
- debug UART pins
- Raspberry Pi B+ compatible GPIO header
- power and reset buttons
This patch adds a dts file that enables UART, MMC and PMIC support.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Banana Pi M2 Ultra is an SBC based on the Allwinner R40 SoC. The
form factor and position of various connectors, leds and buttons is
similar to the Banana Pi M1+, Banana Pi M3, and is exactly the same
as the latest Banana Pi M64.
It features:
- X-Powers AXP221s PMIC connected to i2c0
- 2 GB DDR3 DRAM
- 8 GB eMMC
- micro SD card slot
- DC power jack
- HDMI output
- MIPI DSI connector
- 2x USB 2.0 hosts
- 1x USB 2.0 OTG
- gigabit ethernet with Realtek RTL8211E transceiver
- WiFi/Bluetooth with AP6212 chip, with external antenna connector
- SATA and power connectors for native SATA support
- camera sensor connector
- consumer IR receiver
- audio out headphone jack
- onboard microphone
- red, green, and blue LEDs
- debug UART pins
- Li-Po battery connector
- Raspberry Pi B+ compatible GPIO header
- power, reset, and boot control buttons
This patch adds a dts file that enables UART, MMC and PMIC support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Odroid HC1 board is based on Odroid XU4 board, but it has no HDMI,
no eMMC, no built-in USB3.0 hub, no extension port pins, and no GPIO
button. USB3.0 ports are used for built-in JMicron USB to SATA bridge
and Gigabit R8152 ethernet chips. HC1 uses only passive cooling.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Working items:
- 800MHz CPU
- 2GB of RAM (DDR3)
- 4GB of eMMC storage
- 1T1R WiFi 2.4 GHz
- Power management support
- 1x 10/100/1000 Mbps Ethernet WAN port
- 2x USB 2.0 Host
- PCIe
- HDMI/VGA/LVDS display
- 1x UART for RS232/422/485
- 2x UART for RS232
- 1x UART for serial console
- 1x CAN bus
Specification: http://nutsboard.org/pistachio
Signed-off-by: YuanCheng Cheng <onlywig@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for iWave RainboW-G22D-SODIMM board based on RZ/G1E.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The TBS A711 is a tablet with an A83T, a modem, wifi/BT chip, an eMMC and a
1024x600 LVDS display.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A20-OLinuXino-MICRO has option with onboard eMMC chip. For
now it's only shipped with 4BG chip, but in the future this
may change.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds initial support for rk3288 based
Vyasa board, which is made by Amarula Solutions.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
One new board, and a revert of a patch relying on a binding not stable
enough so that we can commit to it.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZo+BEAAoJEBx+YmzsjxAgjlAP/i6utvIWo08uofBGwABwxRL9
F+fToDOXwGDR6u0FlC7hB1dq6PtEe41qQwNIZC3UnQ7inoUGOYSiY1NBvci+4FEm
ibvqcsXwLtkbSdK3fPSvSxnn4gFqyZf0lW1dUUbnpOCV2p8E5phzw7zdAvkvySD6
S0XJHd5zXNXYfPuXYnK6etMaaVbybeCKdbwu3UTdgyCFgksO6Iufc06khC7DYdrv
EmOPcI6APAx+iYUgrfMJ3XaAG8ps/mmTM5lirofTjO2Le2xZT3mxzEIeoF0CuCuO
h0vzfDpjy7hoGq4QuR/46B03wePvP/azKUdswe76rHm5rv1OlwdT+mbF1UMatKIs
fzpqOpThNqO41wmPOaDfYYp18uBch2sazN7C1Gun4YBzGZ38VINSOzX85sQvaWVw
qb+z+zQYETMPwYzhdTz/Dxnzfh0sSpJF6lueGgYwLxf1IPZiV/9r3EMoD8px++9E
yJuaomTJn136fzK/rZMAbkqkebRIVmdmRyzccwvf4lqhWc45przvpRLuk1DWClHr
mED8W+yvxY0RQX+JEhg0DJXRPbFElpawx/2wLGBnyozycs75SZmKpuMm1lC4Fgvk
16G5/xxUHrHhCRTdVTyKPNuvEKUQLiEqgvGPhjyOfaQuMM57hpyioIHiUEiX2WiN
Nle9Mo522KZU7ITcUOWG
=jgbH
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.14-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.14, take 3
One new board, and a revert of a patch relying on a binding not stable
enough so that we can commit to it.
* tag 'sunxi-dt-for-4.14-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
ARM: sun8i: a83t: Add device tree for Sinovoip Bananapi BPI-M3
Signed-off-by: Olof Johansson <olof@lixom.net>
The BPI-M3 is an Allwinner A83T based SBC in the Bananapi/Bpi family.
It is roughly the same form factor as the BPI-M1+, with roughly the
same peripherals and connectors:
- 2GB LPDDR3 DRAM
- 8GB eMMC
- Micro-SD card slot
- HDMI output
- Headset (stereo + mic) jack
- Onboard mic
- Gigabit Ethernet with RTL8211E transceiver
- Ampak AP6212 WiFi + BT
- USB OTG connector
- USB-to-SATA bridge connected through a USB 2.0 hub
- Consumer IR receiver
- MIPI DSI LCD panel connector
- Camera interface (parallel and MIPI CSI) connector
- 3 LEDs (Red, Green, Blue), of which 2 are controllable (GB)
- Raspberry Pi 2 compatible GPIO header
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
- A series from Andrew Lunn updating imx6-rdu2 board to enable
on-board Marvell switch support.
- A series from Jagan Teki updating imx6ul-isiot and imx6ul-geam to
enable audio card and FEC support.
- Add support for Toradex Ixora V1.1 and Apalis Evaluation Board
along with some cleanups.
- Enable DRM display support for imx6ul-evk and imx7d-sdb board.
- Add i.MX53 based Beckhoff CX9020 board support.
- Add GPMI NAND and APBH DMA devices for i.MX7 and enables NAND support
for imx7-colibri board.
- Enables the ADV7180 analog video decoder sensor connected to the
IMX6 IPU on various Gateworks Ventana boards.
- Minor updates on misc boards and some random cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZloV7AAoJEFBXWFqHsHzOeIAH/ieM8fZEeUHO9waD4aoQJulp
kQHbJFKlEaQrB/y9LVUmNae0w/dpOaf5k/NVtfLQAZQhMqN6Y9XFQA0fnUAgiNbs
fknQpL6VnrO7nGUDEbIUommrRDPEVN9SEiiPpLpD938QjUDxTAibb8++QQOHC/S6
NLQbYMvubDTaUXkOiRodLQU6U/RQ5Byzmu+ytuKjlB1la0OzMegebD/OMXZtgysx
hcEDVBIEZmQO1TPrl5p6IZjjdHs1ua4gfRLQWq1RPXECakHJuyCPKILibyRID15j
w0C+sTxP1uIN950VYzufrbLIdyheWHSrx0FZSWa7tnus8W+h8kBAUd6NxyHLiyU=
=0Cwx
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree updates for 4.14" from Shawn Guo:
- A series from Andrew Lunn updating imx6-rdu2 board to enable
on-board Marvell switch support.
- A series from Jagan Teki updating imx6ul-isiot and imx6ul-geam to
enable audio card and FEC support.
- Add support for Toradex Ixora V1.1 and Apalis Evaluation Board
along with some cleanups.
- Enable DRM display support for imx6ul-evk and imx7d-sdb board.
- Add i.MX53 based Beckhoff CX9020 board support.
- Add GPMI NAND and APBH DMA devices for i.MX7 and enables NAND support
for imx7-colibri board.
- Enables the ADV7180 analog video decoder sensor connected to the
IMX6 IPU on various Gateworks Ventana boards.
- Minor updates on misc boards and some random cleanups.
* tag 'imx-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (47 commits)
ARM: dts: imx6q-bx50v3: Enable i2c recovery mechanism
ARM: dts: imx6q-apalis-eval: add support for Apalis Evaluation Board
ARM: dts: imx6: add support for Toradex Ixora V1.1 carrier board
ARM: dts: imx6qdl-apalis: imx6q-apalis-ixora: use i2c from dwc hdmi
ARM: dts: imx6q-apalis-ixora: add camera i2c bus definition
ARM: dts: imx6q-apalis-ixora: get rid of obsolete fusion comment
ARM: dts: imx6qdl-apalis: reword cam i2c comment
ARM: dts: imx6qdl-apalis: imx6q-apalis-ixora: get rid of tegra legacy gen1_i2c comment
ARM: dts: imx6q-apalis-ixora: combine aliases
ARM: dts: imx6qdl-apalis: split usdhc1 pinctrl to support 4- and 8-bit
ARM: dts: imx6q-apalis-ixora: fix usdhc2 pinctrl property
ARM: dts: imx6ul-liteboard: Support poweroff
ARM: dts: imx: add CX9020 Embedded PC device tree
ARM: dts: imx53: add alternative UART2 configuration
ARM: dts: imx53: add srtc node
dt-bindings: arm: Add entry for Beckhoff CX9020
ARM: dts: i.MX25: add RNGB node to dtsi
ARM: dts: imx6ul-14x14-evk: Remove unrelated pin from ENET group
ARM: dts: imx7d-sdb: Add flexcan support
ARM: dts: imx7-colibri: add NAND support
...
4.14, please pull the following:
- Eric moves the bcm2837 DT file from arm64 to arm because it created a maintenance
problem and would have required either duplication or cross merges
- Stefan changes how the pinmuxing is defined and pushes it at the board level
to support Raspberry Pi Zero Wireless. He then adds supports for the actual
Raspberry Pi Zero Wireless board along with binding documentation. Stefan
also defines a proper SMP enable-method property and binding for BCM2836
(Raspbery Pi 2)
- Rafal describes the BCM5301X USB ports correctly in Device Tree such that
it becomes possible to assign them to specific LED triggers (e.g: USB activity).
He does the same thing for BCM53573 and defines default LED triggers for USB.
- Jon provides a fix for Northstar Plus which consists in correctly defining
the "dma-coherent" property for peripherals which are DMA coherent. He also
does a bit of re-arrangement of the USB DT nodes and finally adds USB 3 PHY
and host controller support for NorthStar Plus
- Florian adds support for Broadcom's BCM947189ACDBMR reference board which is
based on BCM47182/53573 and which supports external MoCA (BCM6802)
- Ray fixes the wrong UART2 base address for Cygnus
- Scott moves the v3d node in the proper unit address order and defines the correct
UART alias for the BCM91130_entphn reference board to be UART3
- Jason adds the DT node for the Cygnus Cortex-A9 Performance Monitoring Unit
- Jonathan adds a bunch of additional peripherals to the Cygnus DTS include file:
SDHCI, Keypad, SPI, DMA and pinmux configurations
- Raveendra adds the Cygnus OHCI and EHCI Device Tree nodes
-----BEGIN PGP SIGNATURE-----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=WUr3
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.14/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.14" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree changes for
4.14, please pull the following:
- Eric moves the bcm2837 DT file from arm64 to arm because it created a maintenance
problem and would have required either duplication or cross merges
- Stefan changes how the pinmuxing is defined and pushes it at the board level
to support Raspberry Pi Zero Wireless. He then adds supports for the actual
Raspberry Pi Zero Wireless board along with binding documentation. Stefan
also defines a proper SMP enable-method property and binding for BCM2836
(Raspbery Pi 2)
- Rafal describes the BCM5301X USB ports correctly in Device Tree such that
it becomes possible to assign them to specific LED triggers (e.g: USB activity).
He does the same thing for BCM53573 and defines default LED triggers for USB.
- Jon provides a fix for Northstar Plus which consists in correctly defining
the "dma-coherent" property for peripherals which are DMA coherent. He also
does a bit of re-arrangement of the USB DT nodes and finally adds USB 3 PHY
and host controller support for NorthStar Plus
- Florian adds support for Broadcom's BCM947189ACDBMR reference board which is
based on BCM47182/53573 and which supports external MoCA (BCM6802)
- Ray fixes the wrong UART2 base address for Cygnus
- Scott moves the v3d node in the proper unit address order and defines the correct
UART alias for the BCM91130_entphn reference board to be UART3
- Jason adds the DT node for the Cygnus Cortex-A9 Performance Monitoring Unit
- Jonathan adds a bunch of additional peripherals to the Cygnus DTS include file:
SDHCI, Keypad, SPI, DMA and pinmux configurations
- Raveendra adds the Cygnus OHCI and EHCI Device Tree nodes
* tag 'arm-soc/for-4.14/devicetree' of http://github.com/Broadcom/stblinux:
ARM: BCM53573: Specify ports for USB LED for Tenda AC9
ARM: dts: cygnus: Add generic-ehci/ohci nodes
ARM: dts: cygnus: add serial0 alias for uart3 on bcm91130_entphn
ARM: dts: cygnus: Add additional peripherals to dtsi
ARM: dts: cygnus: Enable Performance Monitoring Unit
ARM: dts: cygnus: place v3d in proper address ordered location
ARM: dts: cygnus: Fix incorrect UART2 register base
ARM: dts: bcm283x: Add 32-bit enable method for SMP
dt-bindings: arm: add SMP enable-method for BCM2836
ARM: dts: BCM53573: Add Broadcom BCM947189ACDBMR board support
ARM: dts: BCM5301X: Specify USB ports for USB LEDs of few devices
ARM: dts: NSP: Add USB3 and USB3 PHY to NSP
ARM: dts: NSP: Rearrage USB entries
ARM: dts: NSP: Add dma-coherent to relevant DT entries
ARM: dts: bcm2835: Add Raspberry Pi Zero W
dt-bindings: bcm: Add Raspberry Pi Zero W
ARM: bcm283x: Define UART pinmuxing on board level
ARM: dts: BCM5301X: Specify USB ports for each controller
ARM: dts: bcm283x: Move the BCM2837 DT contents from arm64 to arm.
These got delayed a bit because the iodelay changes had to be
reworked for a missing Signed-off-by. And the beagleboard-x15
wants to use iodelay too for mmc:
- A series of changes to add dra7 iodelay data used for mmc
- Add support for new beagleBoard-x15 revision c
- Fix logicpd-torpedo-37xx-devkit mmc card detect direction
-----BEGIN PGP SIGNATURE-----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=R16f
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.14/dt-v3-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "device tree changes for omaps for v4.14, part2" from Tony Lindgren:
Second set of device tree changes for omaps for v4.14 merge window.
These got delayed a bit because the iodelay changes had to be
reworked for a missing Signed-off-by. And the beagleboard-x15
wants to use iodelay too for mmc:
- A series of changes to add dra7 iodelay data used for mmc
- Add support for new beagleBoard-x15 revision c
- Fix logicpd-torpedo-37xx-devkit mmc card detect direction
* tag 'omap-for-v4.14/dt-v3-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3: logicpd-torpedo-37xx-devkit: Fix MMC1 cd-gpio
ARM: dts: am57xx-beagle-x15: Add support for rev C
ARM: dts: dra71-evm: Add pinmux configuration for MMC
ARM: dts: dra72-evm-revc: Add pinmux configuration for MMC
ARM: dts: dra72-evm: Add pinmux configuration for MMC
ARM: dts: am572x-idk: Add pinmux configuration for MMC
ARM: dts: am571x-idk: Add pinmux configuration for MMC
ARM: dts: am57xx-idk: Move common MMC/SD properties to common file
ARM: dts: am57xx-beagle-x15: Add pinmux configuration for MMC
ARM: dts: dra7-evm: Add pinmux configuration for MMC
ARM: dts: dra74x: Create a common file with MMC/SD IOdelay data
ARM: dts: dra72x: Create a common file with MMC/SD IOdelay data
Latest update to the BeagleBoard-X15 platform (revision C). This board contains
a silicon update (Rev 2.0), which includes a fix for the 2nd ethernet phy when
running at 1000 Mbps speeds.
This board can be indentified by the [C.00] after [BBRDX15_] in the at24 eeprom:
[BBRDX15_C.001731PX150249]
Rev C is now in full production and boards are available for end users.
https://beagleboard.org/x15https://github.com/beagleboard/beagleboard-x15/
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Nishanth Menon <nm@ti.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- A series of changes for dra7 and am572 to use generic
MMC vqmmc regulator
- Clean-up tps65217 internal interrupts to define them
only in tps65217.dtsi
- Add dra7 iodelay pinctrl driver configuration
- Add buzzer support for am437x-gp-evm
- Disable HDMI CEC internal pull-ups as it seems that
all boards have an external pull for these
- Remove unnecessary interrupt-parent for omap3
- Configure droid 4 vaudio regulator initial mode and
add vibrator
- Enable NAND dma prefetch for am335x-evm, am437x and dra7
- Add pcie1 dt node for EP mode for am57x and dra7
- Add support for new dra76x SoCs and dra76x-evm
-----BEGIN PGP SIGNATURE-----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=zikX
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.14/dt-v3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Device tree changes for omaps for v4.14 merge window" from Tony Lindgren:
- A series of changes for dra7 and am572 to use generic
MMC vqmmc regulator
- Clean-up tps65217 internal interrupts to define them
only in tps65217.dtsi
- Add dra7 iodelay pinctrl driver configuration
- Add buzzer support for am437x-gp-evm
- Disable HDMI CEC internal pull-ups as it seems that
all boards have an external pull for these
- Remove unnecessary interrupt-parent for omap3
- Configure droid 4 vaudio regulator initial mode and
add vibrator
- Enable NAND dma prefetch for am335x-evm, am437x and dra7
- Add pcie1 dt node for EP mode for am57x and dra7
- Add support for new dra76x SoCs and dra76x-evm
* tag 'omap-for-v4.14/dt-v3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
ARM: dts: nokia n900: update dts with camera support
ARM: dts: Add support for dra76-evm
ARM: dts: Add support for dra76x family of devices
ARM: dts: DRA7: Add pcie1 dt node for EP mode
ARM: dts: am335x: add support for Moxa UC-8100-ME-T open platform
ARM: dts: dra7xx: Enable NAND dma prefetch by default
ARM: dts: am437xx: Enable NAND dma prefetch by default
ARM: dts: am335x-evm: Enable NAND dma prefetch by default
ARM: dts: omap4-droid4: Add vibrator
ARM: dts: motorola-cpcap-mapphone: set initial mode for vaudio
ARM: dts: omap3: Remove needless interrupt-parent property
ARM: dts: Disable HDMI CEC internal pull-ups
ARM: dts: am437x-gp-evm: Add support for buzzer
ARM: dts: Add dra7 iodelay configuration
ARM: dts: tps65217: Add power button interrupt to the common tps65217.dtsi file
ARM: dts: tps65217: Add charger interrupts to the common tps65217.dtsi file
ARM: dts: omap*: Replace deprecated "vmmc_aux" with "vqmmc"
ARM: dts: am572x-idk: Fix GPIO polarity for MMC1 card detect
ARM: dts: am571x-idk: Fix GPIO polarity for MMC1 card detect
ARM: dts: dra7: Add "max-frequency" property to MMC dt nodes
...
Vanessa Maegima