The DSI controllers are powered by a (typically 1.2V) regulator. Usually
this is always on, so there was no need to support enabling or disabling
it thus far. But in order not to consume any power when DSI is inactive,
give the driver a chance to enable or disable the supply as needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Revert commit 18ebc0f404 "drm/tegra: hdmi: Enable VDD earlier for
hotplug/DDC" and instead add a new supply for the +5V pin on the HDMI
connector.
The vdd-supply property refers to the regulator that supplies the
AVDD_HDMI input on Tegra, rather than the +5V HDMI connector pin. This
was never a problem before, because all boards had that pin hooked up to
a regulator that was always on. Starting with Dalmore and continuing
with Venice2, the +5V pin is controllable via a GPIO. For reasons
unknown, the GPIO ended up as the controlling GPIO of the AVDD_HDMI
supply in the Dalmore and Venice2 DTS files. But that's not correct.
Instead, a separate supply must be introduced so that the +5V pin can be
controlled separately from the supplies that feed the HDMI block within
Tegra.
A new hdmi-supply property is introduced that takes the place of the
vdd-supply and vdd-supply is only enabled when HDMI is enabled rather
than all the time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Exynos drm hdmi driver used to get dummy hdmiphy clock to
control the PMU bit for hdmiphy. This bit needs to be set
before setting any resolution to hdmi hardware. This was
handled using dummy hdmiphy clock which is removed here.
PMU is already defined as system controller for exynos
SoCs. Hdmi driver is modified to control the phy enable bit
inside PMU using regmap interfaces.
Devicetree binding document for hdmi is also updated.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Enable support for hdmi for exynos5420 hdmiphy. Add
compatible string in the of_match table. Also added
hdmiphy configuration values for exynos5420.
Signed-off-by: Rahul Sharma <Rahul.Sharma@samsung.com>
Signed-off-by: Shirish S <s.shirish@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Certain bridge chips use a GPIO to indicate the cable status instead
of the I_DP_HPD pin. This adds an optional device-tree property,
"samsung,hpd-gpio", to the exynos-dp controller which indicates that
the specified GPIO should be used for hotplug detection.
The GPIO is then set up as an edge-triggered interrupt where the
rising edge indicates hotplug-in and the falling edge indicates hotplug-out.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
A few collections of small eggs that have been gathered during
the Easter holidays. Mostly small ASoC fixes, with a HD-audio
quirk and a workaround for Nvidia controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=M31u
-----END PGP SIGNATURE-----
Merge tag 'sound-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few collections of small eggs that have been gathered during the
Easter holidays. Mostly small ASoC fixes, with a HD-audio quirk and a
workaround for Nvidia controller"
* tag 'sound-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Suppress CORBRP clear on Nvidia controller chips
ALSA: hda - add headset mic detect quirk for a Dell laptop
ASoC: jz4740: Remove Makefile entry for removed file
ASoC: Intel: Fix audio crash due to negative address offset
ASoC: dapm: Fix widget double free with auto-disable DAPM kcontrol
ASoC: Intel: Fix incorrect sizeof() in sst_hsw_stream_get_volume()
ASoC: Intel: some incorrect sizeof() usages
ASoC: cs42l73: Convert to use devm_gpio_request_one
ASoC: cs42l52: Convert to use devm_gpio_request_one
ASoC: tlv320aic31xx: document that the regulators are mandatory
ASoC: fsl_spdif: Fix wrong OFFSET of STC_SYSCLK_DIV
ASoC: alc5623: Fix regmap endianness
ASoC: tlv320aic3x: fix shared reset pin for DT
ASoC: rsnd: fix clock prepare/unprepare
s/interrupts-names/interrupt-names/g
s/clocks-names/clock-names/g
Some of the binding files and device tree files get this wrong and the
kernel won't be able to pick it up. Fix them up now so that they don't
get widely used.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by : Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Pull more networking fixes from David Miller:
1) Fix mlx4_en_netpoll implementation, it needs to schedule a NAPI
context, not synchronize it. From Chris Mason.
2) Ipv4 flow input interface should never be zero, it should be
LOOPBACK_IFINDEX instead. From Cong Wang and Julian Anastasov.
3) Properly configure MAC to PHY connection in mvneta devices, from
Thomas Petazzoni.
4) sys_recv should use SYSCALL_DEFINE. From Jan Glauber.
5) Tunnel driver ioctls do not use the correct namespace, fix from
Nicolas Dichtel.
6) Fix memory leak on seccomp filter attach, from Kees Cook.
7) Fix lockdep warning for nested vlans, from Ding Tianhong.
8) Crashes can happen in SCTP due to how the auth_enable value is
managed, fix from Vlad Yasevich.
9) Wireless fixes from John W Linville and co.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
net: sctp: cache auth_enable per endpoint
tg3: update rx_jumbo_pending ring param only when jumbo frames are enabled
vlan: Fix lockdep warning when vlan dev handle notification
seccomp: fix memory leak on filter attach
isdn: icn: buffer overflow in icn_command()
ip6_tunnel: use the right netns in ioctl handler
sit: use the right netns in ioctl handler
ip_tunnel: use the right netns in ioctl handler
net: use SYSCALL_DEFINEx for sys_recv
net: mdio-gpio: Add support for separate MDI and MDO gpio pins
net: mdio-gpio: Add support for active low gpio pins
net: mdio-gpio: Use devm_ functions where possible
ipv4, route: pass 0 instead of LOOPBACK_IFINDEX to fib_validate_source()
ipv4, fib: pass LOOPBACK_IFINDEX instead of 0 to flowi4_iif
mlx4_en: don't use napi_synchronize inside mlx4_en_netpoll
net: mvneta: properly configure the MAC <-> PHY connection in all situations
net: phy: add minimal support for QSGMII PHY
sfc:On MCDI timeout, issue an FLR (and mark MCDI to fail-fast)
mwifiex: fix hung task on command timeout
mwifiex: process event before command response
...
Here are a number of small tty/serial driver fixes for 3.15-rc2. Also
in here are some Documentation file removals for drivers that we removed
a long time ago, no need to keep it around any longer.
All of these have been in linux-next for a bit.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlNRmhMACgkQMUfUDdst+yl1egCgi9FsrVUE57dZ2AJNuVwxeh90
cDQAoIAbaKSE1ooen/txjFI27rB92qgZ
=d+yo
-----END PGP SIGNATURE-----
Merge tag 'tty-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty/serial driver fixes for 3.15-rc2. Also
in here are some Documentation file removals for drivers that we
removed a long time ago, no need to keep it around any longer.
All of these have been in linux-next for a bit"
* tag 'tty-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250, disable "too much work" messages"
serial: amba-pl011: fix regression, causing an Oops on rmmod
tty: Fix help text of SYNCLINK_CS
tty: fix memleak in alloc_pid
ttyprintk: Allow built as a module
ttyprintk: Fix wrong tty_unregister_driver() call in the error path
serial: 8250, disable "too much work" messages
Documentation/serial: Delete obsolete driver documentation
serial: omap: Fix missing pm_runtime_resume handling by simplifying code
serial_core: Fix pm imbalance on unbind
serial: pl011: change Rx burst size to half of trigger level
serial: timberdale: Depend on X86_32
serial: st-asc: Fix SysRq char handling
Revert "serial: clps711x: Give a chance to perform useful tasks during wait loop"
serial_core: Fix conditional start_tx on ring buffer not empty
serial: efm32: use $vendor,$device scheme for compatible string
serial: omap: free the wakeup settings in remove
The driver will not probe if regulators are not provided. Move the regulator
properties to the required section.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Wolfram Sang pointed out that "efm32,$device" is non-standard. So use the
common scheme and prefix device with "efm32-". The old compatible string
is left in place until arch/arm/boot/dts/efm32* is fixed.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds the necessary definitions for the PHY layer to
recognize "qsgmii" as a valid PHY interface. A QSMII interface, as
defined at
http://en.wikipedia.org/wiki/Media_Independent_Interface#Quad_Serial_Gigabit_Media_Independent_Interface,
is "is a method of combining four SGMII lines into a 5Gbit/s
interface. QSGMII, like SGMII, uses LVDS signalling for the TX and RX
data and a single LVDS clock signal. QSGMII uses significantly fewer
signal lines than four SGMII busses."
This type of MAC <-> PHY connection might require special handling on
the MAC driver side, so it should be possible to express this type of
MAC <-> PHY connection, for example in the Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: devicetree@vger.kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using "digi" for Digi International Inc.
Additionally, this patch keep "dlink" entry sorted alphabetically.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a number of eeproms and temperature sensors/fan controllers used
by kirkwood boards.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a number of vendor prefixes by kirkwood devices. These are not all
stock tickers, but have been in use for a while so changing would not
be easy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Rob Herring <robh@kernel.org>
Marvell Kirkwood SoC binding have not yet been documented. Add the
documentation including the supported SoCs and boards.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Rob Herring <robh@kernel.org>
Newhaven Display provides the worldwide marketplace with cost
effective high quality display devices ranging from OLED and LCD
Displays to VFD Displays.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Rob Herring <robh@kernel.org>
This trivial patch adds ISEE 2007 S.L. to the list of
devicetree vendor prefixes.
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Rob Herring <robh@kernel.org>
A few driver specific fixes, the main one being the fix for handling of
complete callbacks that are open coded in individual drivers to allow
callers to omit the completion. As we move things into the core that
sort of issue should become less and less common.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rgeq
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes, the main one being the fix for handling
of complete callbacks that are open coded in individual drivers to
allow callers to omit the completion. As we move things into the core
that sort of issue should become less and less common"
* tag 'spi-v3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: qup: Depend on ARCH_QCOM
spi: efm32: Update binding document to make "efm32,location" property optional
spi: omap2-mcspi: Convert to use devm_kcalloc
spi: Always check complete callback before calling it
Here is a bunch of small fixes that have been collected since the
previous pull request. In addition to various misc fixes, the
following are included:
- HD-audio quirks for Dell, HP, Chromebook, and ALC28x codecs
- HD-audio AMD HDMI regression fix
- Continued PM support/fixes for ice1712 driver
- Multiplatform fixes for ASoC samsung drivers
- Addition of device id tables to a few ASoC drivers
- Bit clock polarity config and error flag fixes in ASoC fsl_sai
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=7zfG
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here is a bunch of small fixes that have been collected since the
previous pull request. In addition to various misc fixes, the
following are included:
- HD-audio quirks for Dell, HP, Chromebook, and ALC28x codecs
- HD-audio AMD HDMI regression fix
- Continued PM support/fixes for ice1712 driver
- Multiplatform fixes for ASoC samsung drivers
- Addition of device id tables to a few ASoC drivers
- Bit clock polarity config and error flag fixes in ASoC fsl_sai"
* tag 'sound-fix-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (32 commits)
ALSA: usb-audio: Suppress repetitive debug messages from retire_playback_urb()
ALSA: hda - Make full_reset boolean
ALSA: hda - add headset mic detect quirk for a Dell laptop
sound: dmasound: use module_platform_driver_probe()
ALSA: au1x00: use module_platform_driver()
ALSA: hda - Use runtime helper to check active state.
ALSA: ice1712: Fix boundary checks in PCM pointer ops
ASoC: davinci-mcasp: Fix bit clock polarity settings
ASoC: samsung: Fix build on multiplatform
ASoC: fsl_sai: Fix Bit Clock Polarity configurations
ALSA: hda - Do not assign streams in reverse order
ALSA: hda/realtek - Add eapd shutup to ALC283
ALSA: hda/realtek - Change model name alias for ChromeOS
ASoC: da732x: Print correct major id
ALSA: hda/realtek - Improve HP depop when system change power state on Chromebook
ASoC: cs42l52: Fix mask for REVID
sound/oss: Remove uncompilable DBG macro use
ALSA: ice1712: Save/restore routing and rate registers
ALSA: ice1712: restore AK4xxx volumes on resume
ASoC: alc56(23|32): fix undefined return value of probing code
...
Pull LED updates from Bryan Wu:
"This cycle we got:
- new driver for leds-mc13783
- bug fixes
- code cleanup"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: make sure we unregister a trigger only once
leds: leds-pwm: properly clean up after probe failure
leds: clevo-mail: Make probe function __init
leds-ot200: Fix dependencies
leds-gpio: of: introduce MODULE_DEVICE_TABLE for module autoloading
leds: clevo-mail: remove __initdata marker
leds: leds-ss4200: remove __initdata marker
leds: blinkm: remove unnecessary spaces
leds: lp5562: remove unnecessary parentheses
leds: leds-ss4200: remove DEFINE_PCI_DEVICE_TABLE macro
leds: leds-s3c24xx: Trivial cleanup in header file
drivers/leds: delete non-required instances of include <linux/init.h>
leds: leds-gpio: add retain-state-suspended property
leds: leds-mc13783: Add devicetree support
leds: leds-mc13783: Remove unnecessary cleaning of registers on exit
leds: leds-mc13783: Use proper "max_brightness" value fo LEDs
leds: leds-mc13783: Use LED core PM functions
leds: leds-mc13783: Add MC34708 LED support
leds: Turn off led if blinking is disabled
ledtrig-cpu: Handle CPU hot(un)plugging
Pull slave-dmaengine updates from Vinod Koul:
- New driver for Qcom bam dma
- New driver for RCAR peri-peri
- New driver for FSL eDMA
- Various odd fixes and updates thru the subsystem
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (29 commits)
dmaengine: add Qualcomm BAM dma driver
shdma: add R-Car Audio DMAC peri peri driver
dmaengine: sirf: enable generic dt binding for dma channels
dma: omap-dma: Implement device_slave_caps callback
dmaengine: qcom_bam_dma: Add device tree binding
dma: dw: Add suspend and resume handling for PCI mode DW_DMAC.
dma: dw: allocate memory in two stages in probe
Add new line to test result strings produced in verbose mode
dmaengine: pch_dma: use tasklet_kill in teardown
dmaengine: at_hdmac: use tasklet_kill in teardown
dma: cppi41: start tear down only if channel is busy
usb: musb: musb_cppi41: Dont reprogram DMA if tear down is initiated
dmaengine: s3c24xx-dma: make phy->irq signed for error handling
dma: imx-dma: Add missing module owner field
dma: imx-dma: Replace printk with dev_*
dma: fsl-edma: fix static checker warning of NULL dereference
dma: Remove comment about embedding dma_slave_config into custom structs
dma: mmp_tdma: move to generic device tree binding
dma: mmp_pdma: add IRQF_SHARED when request irq
dma: edma: Fix memory leak in edma_prep_dma_cyclic()
...
Pull i2c updates from Wolfram Sang:
"Here is the pull request from the i2c subsystem. It got a little
delayed because I needed to wait for a dependency to be included
(commit b424080a9e: "reset: Add optional resets and stubs"). Plus,
I had some email problems. All done now, the highlights are:
- drivers can now deprecate their use of i2c classes. That shouldn't
be used on embedded platforms anyhow and was often blindly
copy&pasted. This mechanism gives users time to switch away and
ultimately boot faster once the use of classes for those drivers is
gone for good.
- new drivers for QUP, Cadence, efm32
- tracepoint support for I2C and SMBus
- bigger cleanups for the mv64xxx, nomadik, and designware drivers
And the usual bugfixes, cleanups, feature additions. Most stuff has
been in linux-next for a while. Just some hot fixes and new drivers
were added a bit more recently."
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (63 commits)
i2c: cadence: fix Kconfig dependency
i2c: Add driver for Cadence I2C controller
i2c: cadence: Document device tree bindings
Documentation: i2c: improve section about flags mangling the protocol
i2c: qup: use proper type fro clk_freq
i2c: qup: off by ones in qup_i2c_probe()
i2c: efm32: fix binding doc
MAINTAINERS: update I2C web resources
i2c: qup: New bus driver for the Qualcomm QUP I2C controller
i2c: qup: Add device tree bindings information
i2c: i2c-xiic: deprecate class based instantiation
i2c: i2c-sirf: deprecate class based instantiation
i2c: i2c-mv64xxx: deprecate class based instantiation
i2c: i2c-designware-platdrv: deprecate class based instantiation
i2c: i2c-davinci: deprecate class based instantiation
i2c: i2c-bcm2835: deprecate class based instantiation
i2c: mv64xxx: Fix reset controller handling
i2c: omap: fix usage of IS_ERR_VALUE with pm_runtime_get_sync
i2c: efm32: new bus driver
i2c: exynos5: remove unnecessary cast of void pointer
...
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior.
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V.
- Add GPIO descriptor based slot-gpio card detect API.
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c.
- mmci: Support HW busy detection on ux500.
- omap: Support MMC_ERASE.
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23.
- rtsx: Support pre-req/post-req async.
- sdhci: Add support for Realtek RTS5250 controllers.
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect.
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support.
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6S8w
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
- Additional cache flushing during boot (needed in the presence of
external caches or under virtualisation)
- DMA range invalidation fix for non cache line aligned buffers
- Build failure fix with !COMPAT
- Kconfig update for STRICT_DEVMEM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=mDkd
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull second set of arm64 updates from Catalin Marinas:
"A second pull request for this merging window, mainly with fixes and
docs clarification:
- Documentation clarification on CPU topology and booting
requirements
- Additional cache flushing during boot (needed in the presence of
external caches or under virtualisation)
- DMA range invalidation fix for non cache line aligned buffers
- Build failure fix with !COMPAT
- Kconfig update for STRICT_DEVMEM"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix DMA range invalidation for cache line unaligned buffers
arm64: Add missing Kconfig for CONFIG_STRICT_DEVMEM
arm64: fix !CONFIG_COMPAT build failures
Revert "arm64: virt: ensure visibility of __boot_cpu_mode"
arm64: Relax the kernel cache requirements for boot
arm64: Update the TCR_EL1 translation granule definitions for 16K pages
ARM: topology: Make it clear that all CPUs need to be described
This contains OMAP related fbdev changes for 3.15. The bulk of the patches are
for adding Device Tree support for OMAP Display Subsystem:
* SoCs: OMAP2/3/4
* Boards: OMAP4 Panda, OMAP4 SDP, OMAP3 Beagle, OMAP3 Beagle-xM, OMAP3
IGEP0020, OMAP3 N900
* Devices: TFP410 Encoder, tpd12s015 HDMI companion chip, Sony acx565akm panel,
MIPI DSI Command mode panel and HDMI, DVI and Analog TV connectors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTQmaWAAoJEPo9qoy8lh71LS8P+QHkUWD22XhPqt2NaeIxFhzU
rq7uW7iMtzIawb+y2+GLHykk4obmJKzpanhe+p3dZMSEG8O4s6IyRx8LoJGLeWoP
LtnV77Fbh3p9Bn1nLkDmszbcdSSbH8VseykfV5yCJ0lhTPjUXwm3JBFJ57AtOqeF
ya/13NCKR0v2FFCy89rOc9Iu+dYbVVNakTWcN1qcZOSjNQ6cLWyq97OmC4BD2mkC
H9u4XC/+UC6WJZT0PVs9cPn7D2QCt1ZR8eULmSL3YO2rXdLLfL87brtCS1uMNXk2
MUq9KVS1Iw+6yk248F9AyHkg5nZOzWoeXxZj0m48kaLlFBfkGuuiRSJZhc5qgBtm
61X6eQDclJUo1tgEmtH1wCFe4M3vZ0ImK21bX3PXO+IBgz4Zb3e3uqOAJy4LREJk
KZnjfwn/Gyp0D21YSZvquAZ+qZeZMttiwIlZVD26+Xt7GincC5e/HPi58nJ5IcQQ
BuUsjI8fjFcYTf5O2DqdAaYo3cpt8tfUwCXL6Iw32SYi4xz1Rocmxe/xnGCUxZHk
j3qAT5NkHcQL5xSMZgNQUyyqST1Ey9lgmLlQmnxknRPCOW35tbRo621CNz+5Z0MR
TJDu5REahAS7jEmeAjD1m1Xs4X0tYltiPgnbCwFtNHCvTdnw3R916quqRcQKaP6d
Irzufbo2EoTG8cVhvE8e
=Mnc1
-----END PGP SIGNATURE-----
Merge tag 'fbdev-omap-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull OMAP fbdev changes from Tomi Valkeinen:
"This is based on the already pulled fbdev-main changes, and this also
merges .dts branch from Tony Lindgren (which has also been pulled), so
that I was able to add the display related .dts changes.
This contains OMAP related fbdev changes for 3.15. The bulk of the
patches are for adding Device Tree support for OMAP Display Subsystem:
- SoCs: OMAP2/3/4
- Boards: OMAP4 Panda, OMAP4 SDP, OMAP3 Beagle, OMAP3 Beagle-xM,
OMAP3 IGEP0020, OMAP3 N900
- Devices: TFP410 Encoder, tpd12s015 HDMI companion chip, Sony
acx565akm panel, MIPI DSI Command mode panel and HDMI, DVI and
Analog TV connectors"
* tag 'fbdev-omap-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (45 commits)
OMAPDSS: HDMI: fix interlace output
OMAPDSS: add missing __init for dss_init_ports
ARM: OMAP2+: remove pdata quirks for displays
OMAPDSS: remove DT hacks for regulators
Doc/DT: Add DT binding documentation for tpd12s015 encoder
Doc/DT: Add DT binding documentation for TFP410 encoder
Doc/DT: Add DT binding documentation for Sony acx565akm panel
Doc/DT: Add DT binding documentation for MIPI DSI CM Panel
Doc/DT: Add DT binding documentation for HDMI Connector
Doc/DT: Add DT binding documentation for DVI Connector
Doc/DT: Add DT binding documentation for Analog TV Connector
ARM: omap3-n900.dts: add display information
ARM: omap3-igep0020.dts: add display information
ARM: omap3-beagle-xm.dts: add display information
ARM: omap3-beagle.dts: add display information
ARM: omap4-sdp.dts: add display information
Doc/DT: Add DT binding documentation for OMAP DSS
OMAPDSS: acx565akm: Add DT support
OMAPDSS: connector-analog-tv: Add DT support
OMAPDSS: hdmi-connector: Add DT support
...
- A few SPI NOR ID definitions
- Kill the NAND "max pagesize" restriction
- Fix some x16 bus-width NAND support
- Add NAND JEDEC parameter page support
- DT bindings for NAND ECC
- GPMI NAND updates (subpage reads)
- More OMAP NAND refactoring
- New STMicro SPI NOR driver (now in 40 patches!)
- A few other random bugfixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=CKih
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20140405' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
- A few SPI NOR ID definitions
- Kill the NAND "max pagesize" restriction
- Fix some x16 bus-width NAND support
- Add NAND JEDEC parameter page support
- DT bindings for NAND ECC
- GPMI NAND updates (subpage reads)
- More OMAP NAND refactoring
- New STMicro SPI NOR driver (now in 40 patches!)
- A few other random bugfixes
* tag 'for-linus-20140405' of git://git.infradead.org/linux-mtd: (120 commits)
Fix index regression in nand_read_subpage
mtd: diskonchip: mem resource name is not optional
mtd: nand: fix mention to CONFIG_MTD_NAND_ECC_BCH
mtd: nand: fix GET/SET_FEATURES address on 16-bit devices
mtd: omap2: Use devm_ioremap_resource()
mtd: denali_dt: Use devm_ioremap_resource()
mtd: devices: elm: update DRIVER_NAME as "omap-elm"
mtd: devices: elm: configure parallel channels based on ecc_steps
mtd: devices: elm: clean elm_load_syndrome
mtd: devices: elm: check for hardware engine's design constraints
mtd: st_spi_fsm: Succinctly reorganise .remove()
mtd: st_spi_fsm: Allow loop to run at least once before giving up CPU
mtd: st_spi_fsm: Correct vendor name spelling issue - missing "M"
mtd: st_spi_fsm: Avoid duplicating MTD core code
mtd: st_spi_fsm: Remove useless consts from function arguments
mtd: st_spi_fsm: Convert ST SPI FSM (NOR) Flash driver to new DT partitions
mtd: st_spi_fsm: Move runtime configurable msg sequences into device's struct
mtd: st_spi_fsm: Supply the W25Qxxx chip specific configuration call-back
mtd: st_spi_fsm: Supply the S25FLxxx chip specific configuration call-back
mtd: st_spi_fsm: Supply the MX25xxx chip specific configuration call-back
...
If "efm32,location" property is not provided, keeping what is already
configured in the hardware, so its either the reset default 0 or whatever
the bootloader did.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add device tree binding documentation for the Cadence I2C controller.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This time a few more updates queued up.
* Rework VT-d code to support ACPI devices
* Improvements for memory and PCI hotplug support
in the VT-d driver
* Device-tree support for OMAP IOMMU
* Convert OMAP IOMMU to use devm_* interfaces
* Fixed PASID support for AMD IOMMU
* Other random cleanups and fixes for OMAP, ARM-SMMU
and SHMOBILE IOMMU
Most of the changes are in the VT-d driver because some rework was
necessary for better hotplug and ACPI device support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uy/Z
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU upates from Joerg Roedel:
"This time a few more updates queued up.
- Rework VT-d code to support ACPI devices
- Improvements for memory and PCI hotplug support in the VT-d driver
- Device-tree support for OMAP IOMMU
- Convert OMAP IOMMU to use devm_* interfaces
- Fixed PASID support for AMD IOMMU
- Other random cleanups and fixes for OMAP, ARM-SMMU and SHMOBILE
IOMMU
Most of the changes are in the VT-d driver because some rework was
necessary for better hotplug and ACPI device support"
* tag 'iommu-updates-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (75 commits)
iommu/vt-d: Fix error handling in ANDD processing
iommu/vt-d: returning free pointer in get_domain_for_dev()
iommu/vt-d: Only call dmar_acpi_dev_scope_init() if DRHD units present
iommu/vt-d: Check for NULL pointer in dmar_acpi_dev_scope_init()
iommu/amd: Fix logic to determine and checking max PASID
iommu/vt-d: Include ACPI devices in iommu=pt
iommu/vt-d: Finally enable translation for non-PCI devices
iommu/vt-d: Remove to_pci_dev() in intel_map_page()
iommu/vt-d: Remove pdev from intel_iommu_attach_device()
iommu/vt-d: Remove pdev from iommu_no_mapping()
iommu/vt-d: Make domain_add_dev_info() take struct device
iommu/vt-d: Make domain_remove_one_dev_info() take struct device
iommu/vt-d: Rename 'hwdev' variables to 'dev' now that that's the norm
iommu/vt-d: Remove some pointless to_pci_dev() calls
iommu/vt-d: Make get_valid_domain_for_dev() take struct device
iommu/vt-d: Make iommu_should_identity_map() take struct device
iommu/vt-d: Handle RMRRs for non-PCI devices
iommu/vt-d: Make get_domain_for_dev() take struct device
iommu/vt-d: Make domain_context_mapp{ed,ing}() take struct device
iommu/vt-d: Make device_to_iommu() cope with non-PCI devices
...
Mostly clock driver updates, more Device Tree support in the form of
common functions useful across platforms and a handful of features and
fixes to the framework core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=zk74
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.15' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework changes from Mike Turquette:
"The clock framework changes for 3.15 look similar to past pull
requests. Mostly clock driver updates, more Device Tree support in
the form of common functions useful across platforms and a handful of
features and fixes to the framework core"
* tag 'clk-for-linus-3.15' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: shmobile: fix setting paretn clock rate
clk: shmobile: rcar-gen2: fix lb/sd0/sd1/sdh clock parent to pll1
clk: Fix minor errors in of_clk_init() function comments
clk: reverse default clk provider initialization order in of_clk_init()
clk: sirf: update copyright years to 2014
clk: mmp: try to use closer one when do round rate
clk: mmp: fix the wrong calculation formula
clk: mmp: fix wrong mask when calculate denominator
clk: st: Adds quadfs clock binding
clk: st: Adds clockgen-vcc and clockgen-mux clock binding
clk: st: Adds clockgen clock binding
clk: st: Adds divmux and prediv clock binding
clk: st: Support for A9 MUX clocks
clk: st: Support for ClockGenA9/DDR/GPU
clk: st: Support for QUADFS inside ClockGenB/C/D/E/F
clk: st: Support for VCC-mux and MUX clocks
clk: st: Support for PLLs inside ClockGenA(s)
clk: st: Support for DIVMUX and PreDiv Clocks
clk: support hardware-specific debugfs entries
clk: s2mps11: Use of_get_child_by_name
...
The legacy HAVE_PWM Kconfig symbol is finally being retired. Thanks a
lot to Sascha Hauer for doing that.
Three new drivers are added: Freescale FTM, Cirrus Logic CLPS711X and
Intel Low Power Subsystem.
An assortment of fixes and cleanups rounds things off for this release
cycle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=pbF+
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"The legacy HAVE_PWM Kconfig symbol is finally being retired. Thanks a
lot to Sascha Hauer for doing that.
Three new drivers are added: Freescale FTM, Cirrus Logic CLPS711X and
Intel Low Power Subsystem.
An assortment of fixes and cleanups rounds things off for this release
cycle"
* tag 'pwm/for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: pxa: Constify OF match table
pwm: pxa: Fix typo "pwm" -> "PWM"
Revert "pwm: pxa: Use of_match_ptr()"
pwm: add support for Intel Low Power Subsystem PWM
pwm: Add CLPS711X PWM support
pwm: atmel: correct CDTY calculation
pwm: atmel: Fix polarity handling
Documentation: Add device tree bindings for Freescale FTM PWM.
pwm: Add Freescale FTM PWM driver support
pwm: pxa: Use of_match_ptr()
pwm: samsung: Use SIMPLE_DEV_PM_OPS macro
pwm: renesas-tpu: Add dependency on HAS_IOMEM
pwm: Remove obsolete HAVE_PWM Kconfig symbol
These could not be part of the first cleanup branch, because they either
came too late in the cycle, or they have dependencies on other branches.
Important changes are:
* The integrator platform is almost multiplatform capable after
some reorganization (Linus Walleij)
* Minor cleanups on Zynq (Michal Simek)
* Lots of changes for Exynos and other Samsung platforms, including
further preparations for multiplatform support and the clocks bindings
are rearranged.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=1i9x
-----END PGP SIGNATURE-----
Merge tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late cleanups from Arnd Bergmann:
"These could not be part of the first cleanup branch, because they
either came too late in the cycle, or they have dependencies on other
branches. Important changes are:
- The integrator platform is almost multiplatform capable after some
reorganization (Linus Walleij)
- Minor cleanups on Zynq (Michal Simek)
- Lots of changes for Exynos and other Samsung platforms, including
further preparations for multiplatform support and the clocks
bindings are rearranged"
* tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
devicetree: fix newly added exynos sata bindings
ARM: EXYNOS: Fix compilation error in cpuidle.c
ARM: S5P64X0: Explicitly include linux/serial_s3c.h in mach/pm-core.h
ARM: EXYNOS: Remove hardware.h file
ARM: SAMSUNG: Remove hardware.h inclusion
ARM: S3C24XX: Remove invalid code from hardware.h
dt-bindings: clock: Move exynos-audss-clk.h to dt-bindings/clock
ARM: dts: Keep some essential LDOs enabled for arndale-octa board
ARM: dts: Disable MDMA1 node for arndale-octa board
ARM: S3C64XX: Fix build for implicit serial_s3c.h inclusion
serial: s3c: Fix build of header without serial_core.h preinclusion
ARM: EXYNOS: Allow wake-up using GIC interrupts
ARM: EXYNOS: Stop using legacy Samsung PM code
ARM: EXYNOS: Remove PM initcalls and useless indirection
ARM: EXYNOS: Fix abuse of CONFIG_PM
ARM: SAMSUNG: Move s3c_pm_check_* prototypes to plat/pm-common.h
ARM: SAMSUNG: Move common save/restore helpers to separate file
ARM: SAMSUNG: Move Samsung PM debug code into separate file
ARM: SAMSUNG: Consolidate PM debug functions
ARM: SAMSUNG: Use debug_ll_addr() to get UART base address
...
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
A large part of the arm-soc patches are nowadays DT changes, adding support
for new SoCs, boards and devices without changing kernel source. The plan
is still to move the devicetree files out of the kernel tree and reduce
the amount of churn going on here, but we keep finding reasons to delay
doing that.
Changes are really all over the place, with little sticking out particularly.
We have contributions from a total of 116 people in this branch.
Unfortunately, the size of this branch also causes a significant number
of conflicts at the moment, typically when subsystem maintainers merge
patches that change the driver at the same time as the dts files. In
most cases this could be avoided because the dts changes are supposed
to be compatible in both ways, and we are asking everyone to send ARM
dts changes through our tree only.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUz/11WCrR//JCVInAQIIyRAA0DjdNNQ/A4G2i1nZCiTFH6a4oZy4JarN
ATVPkW/V8avhh+yVNe5FWA44Xe6CDC5TXwMaIsbK+w3Iclj3fplh/MsBkQ9ZT9Sl
LAjJoOjuYucCeDy0WLVioRKZ4PJEDoCu/oZTauIMnmWCOCRxLYpOM3FkAT9oN/Ti
lswpTSLiV1/U3ZSI4M3qn+Sx1VJL8c/hAIWbvf5if2diYkWPk3VOSKyxmD9zLWdD
Iqtb79J+ETVeOIM4sHnx79cG4ZCdpOfRAl7qx6hkJu0YATXESxWhpXVE2McTJuzM
qHKsRRNSfsfSWPeF4angll9o06X/qgdT6C4P2dfH49lGeG7llOttw3OaCx3hWCTe
U5bt26qtbwG2ZbzocaqvideP+rbpQrCH2vdO1embPv5Lu6peMoBWjxy6twSVXJBG
LIymJ0IbiGYxL7BReGqRXt6ehy0BDWBeTSTdsGqgEl2TnxHuS/kgGfJc4D5riiEk
aRPVq10p/k+yo4BZtq2GqXIOG6cqkIQ5lhl5Tg9+MfUlquAONqJP70FgRJDBIw9L
9uJp71bgSsA6eYg2tXoqJtpdjKplDWavgtACzIkFg2qFLyYmKvx+F0AXbeTIsrri
/mIchTyG+dgiIjWvj/Xsf7jhrdzRcl3uKsJwFmk927pIsh24HV8T+LKgHrf+sVcO
qEsEnKGYA6s=
=zl/N
-----END PGP SIGNATURE-----
Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
Lots of changes specific to one of the SoC families. Some that
stick out are:
* mach-qcom gains new features, most importantly SMP support for
the newer chips (Stephen Boyd, Rohit Vaswani)
* mvebu gains support for three new SoCs: Armada 375, 380 and 385
(Thomas Petazzoni and Free-electrons team)
* SMP support for Rockchips (Heiko Stübner)
* Lots of i.MX changes (Shawn Guo)
* Added support for BCM5301x SoC (Hauke Mehrtens)
* Multiplatform support for Marvell Kirkwood and Dove
(Andrew Lunn and Sebastian Hesselbarth doing the final part
of a long journey)
* Unify davinci platforms and remove obsolete ones (Sekhar Nori,
Arnd Bergmann)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=AGpV
-----END PGP SIGNATURE-----
Merge tag 'soc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"Lots of changes specific to one of the SoC families. Some that stick
out are:
- mach-qcom gains new features, most importantly SMP support for the
newer chips (Stephen Boyd, Rohit Vaswani)
- mvebu gains support for three new SoCs: Armada 375, 380 and 385
(Thomas Petazzoni and Free-electrons team)
- SMP support for Rockchips (Heiko Stübner)
- Lots of i.MX changes (Shawn Guo)
- Added support for BCM5301x SoC (Hauke Mehrtens)
- Multiplatform support for Marvell Kirkwood and Dove (Andrew Lunn
and Sebastian Hesselbarth doing the final part of a long journey)
- Unify davinci platforms and remove obsolete ones (Sekhar Nori, Arnd
Bergmann)"
* tag 'soc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (126 commits)
ARM: sunxi: Select HAVE_ARM_ARCH_TIMER
ARM: cache-tauros2: remove ARMv6 code
ARM: mvebu: don't select CONFIG_NEON
ARM: davinci: fix DT booting with default defconfig
ARM: configs: bcm_defconfig: enable bcm590xx regulator support
ARM: davinci: remove tnetv107x support
MAINTAINERS: Update ARM STi maintainers
ARM: restrict BCM_KONA_UART to ARCH_BCM_MOBILE
ARM: bcm21664: Add board support.
ARM: sunxi: Add the new watchog compatibles to the reboot code
ARM: enable ARM_HAS_SG_CHAIN for multiplatform
ARM: davinci: remove da8xx_omapl_defconfig
ARM: davinci: da8xx: fix multiple watchdog device registration
ARM: davinci: add da8xx specific configs to davinci_all_defconfig
ARM: davinci: enable da8xx build concurrently with older devices
ARM: BCM5301X: workaround suppress fault
ARM: BCM5301X: add early debugging support
ARM: BCM5301X: initial support for the BCM5301X/BCM470X SoCs with ARM CPU
ARM: mach-bcm: Remove GENERIC_TIME
ARM: shmobile: APMU: Fix warnings due to improper printk formats
...
These cleanup patches are mainly move stuff around and should all
be harmless. They are mainly split out so that other branches can
be based on top to avoid conflicts.
Notable changes are:
* We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used. (Uwe Kleine-König)
* The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions. (Kumar Gala)
* A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
* Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
* mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
* at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GcBb
-----END PGP SIGNATURE-----
Merge tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"These cleanup patches are mainly move stuff around and should all be
harmless. They are mainly split out so that other branches can be
based on top to avoid conflicts.
Notable changes are:
- We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used (Uwe Kleine-König)
- The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions (Kumar Gala)
- A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
- Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
- mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
- at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people)"
* tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (89 commits)
ARM: hisi: select HAVE_ARM_SCU only for SMP
ARM: efm32: allow uncompress debug output
ARM: prima2: build reset code standalone
ARM: at91: add PWM clock
ARM: at91: move sam9261 SoC to common clk
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
ARM: at91: dt: Add at91sam9261 dt SoC support
ARM: at91: switch sam9rl to common clock framework
ARM: at91/dt: define main clk frequency of at91sam9rlek
ARM: at91/dt: define at91sam9rl clocks
ARM: at91: prepare common clk transition for sam9rl SoCs
ARM: at91: prepare sam9 dt boards transition to common clk
ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
ARM: at91: Add at91sam9rl DT SoC support
ARM: at91: prepare at91sam9rl DT transition
ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
...
Pull ARM changes from Russell King:
- Perf updates from Will Deacon:
- Support for Qualcomm Krait processors (run perf on your phone!)
- Support for Cortex-A12 (run perf stat on your FPGA!)
- Support for perf_sample_event_took, allowing us to automatically decrease
the sample rate if we can't handle the PMU interrupts quickly enough
(run perf record on your FPGA!).
- Basic uprobes support from David Long:
This patch series adds basic uprobes support to ARM. It is based on
patches developed earlier by Rabin Vincent. That approach of adding
hooks into the kprobes instruction parsing code was not well received.
This approach separates the ARM instruction parsing code in kprobes out
into a separate set of functions which can be used by both kprobes and
uprobes. Both kprobes and uprobes then provide their own semantic action
tables to process the results of the parsing.
- ARMv7M (microcontroller) updates from Uwe Kleine-König
- OMAP DMA updates (recently added Vinod's Ack even though they've been
sitting in linux-next for a few months) to reduce the reliance of
omap-dma on the code in arch/arm.
- SA11x0 changes from Dmitry Eremin-Solenikov and Alexander Shiyan
- Support for Cortex-A12 CPU
- Align support for ARMv6 with ARMv7 so they can cooperate better in a
single zImage.
- Addition of first AT_HWCAP2 feature bits for ARMv8 crypto support.
- Removal of IRQ_DISABLED from various ARM files
- Improved efficiency of virt_to_page() for single zImage
- Patch from Ulf Hansson to permit runtime PM callbacks to be available for
AMBA devices for suspend/resume as well.
- Finally kill asm/system.h on ARM.
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (89 commits)
dmaengine: omap-dma: more consolidation of CCR register setup
dmaengine: omap-dma: move IRQ handling to omap-dma
dmaengine: omap-dma: move register read/writes into omap-dma.c
ARM: omap: dma: get rid of 'p' allocation and clean up
ARM: omap: move dma channel allocation into plat-omap code
ARM: omap: dma: get rid of errata global
ARM: omap: clean up DMA register accesses
ARM: omap: remove almost-const variables
ARM: omap: remove references to disable_irq_lch
dmaengine: omap-dma: cleanup errata 3.3 handling
dmaengine: omap-dma: provide register read/write functions
dmaengine: omap-dma: use cached CCR value when enabling DMA
dmaengine: omap-dma: move barrier to omap_dma_start_desc()
dmaengine: omap-dma: move clnk_ctrl setting to preparation functions
dmaengine: omap-dma: improve efficiency loading C.SA/C.EI/C.FI registers
dmaengine: omap-dma: consolidate clearing channel status register
dmaengine: omap-dma: move CCR buffering disable errata out of the fast path
dmaengine: omap-dma: provide register definitions
dmaengine: omap-dma: consolidate setup of CCR
dmaengine: omap-dma: consolidate setup of CSDP
...
Pull exynos media updates from Mauro Carvalho Chehab:
"These are the remaining patches I have for the merge windows. It
basically adds a new sensor and adds the needed DT bits for it to
work"
* 'topic/exynos' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] s5p-fimc: Remove reference to outdated macro
[media] s5p-jpeg: Fix broken indentation in jpeg-regs.h
[media] exynos4-is: Add the FIMC-IS ISP capture DMA driver
[media] exynos4-is: Add support for asynchronous subdevices registration
[media] exynos4-is: Add clock provider for the SCLK_CAM clock outputs
[media] exynos4-is: Use external s5k6a3 sensor driver
[media] V4L: s5c73m3: Add device tree support
[media] V4L: Add driver for s5k6a3 image sensor
[media] Documentation: devicetree: Update Samsung FIMC DT binding
[media] Documentation: dt: Add binding documentation for S5C73M3 camera
[media] Documentation: dt: Add binding documentation for S5K6A3 image sensor
Merge window -fixes pull request as usual. Well, I did sneak in Jani's
drm_i915_private_t typedef removal, need to have fun with a big sed job
too ;-)
Otherwise:
- hdmi interlaced fixes (Jesse&Ville)
- pipe error/underrun/crc tracking fixes, regression in late 3.14-rc (but
not cc: stable since only really relevant for igt runs)
- large cursor wm fixes (Chris)
- fix gpu turbo boost/throttle again, was getting stuck due to vlv rps
patches (Chris+Imre)
- fix runtime pm fallout (Paulo)
- bios framebuffer inherit fix (Chris)
- a few smaller things
* tag 'drm-intel-fixes-2014-04-04' of git://anongit.freedesktop.org/drm-intel: (196 commits)
Skip intel_crt_init for Dell XPS 8700
drm/i915: vlv: fix RPS interrupt mask setting
Revert "drm/i915/vlv: fixup DDR freq detection per Punit spec"
drm/i915: move power domain init earlier during system resume
drm/i915: Fix the computation of required fb size for pipe
drm/i915: don't get/put runtime PM at the debugfs forcewake file
drm/i915: fix WARNs when reading DDI state while suspended
drm/i915: don't read cursor registers on powered down pipes
drm/i915: get runtime PM at i915_display_info
drm/i915: don't read pp_ctrl_reg if we're suspended
drm/i915: get runtime PM at i915_reg_read_ioctl
drm/i915: don't schedule force_wake_timer at gen6_read
drm/i915: vlv: reserve the GT power context only once during driver init
drm/i915: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/overlay: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/ringbuffer: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/display: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/irq: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/gem: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/dma: prefer struct drm_i915_private to drm_i915_private_t
...
