When XIP_KERNEL is enabled, the virt to phys address translation for RAM
is not the same as the virt to phys address translation for .text.
The only way to know where physical RAM is located is to use
PLAT_PHYS_OFFSET.
The MACRO will be useful for other places where there is a similar problem.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We can still override these settings via mach/memory.h, but let's provide
sensible defaults so that SPARSEMEM is available in the multiplatform
kernels.
Two platforms currently use SECTION_SIZE_BITS < 28, but are expected to
work with 28 (albeit slightly less efficiently if not all banks are
populated):
- mach-rpc: uses 26 bits. Based on mach/hardware.h it looks like this
platform puts RAM at 0x1000_0000 - 0x1fff_ffff, and I/O below
0x1000_0000.
- mach-sa1100: uses 27 bits. mach/memory.h indicates that RAM occupies
the entire range of 0xc000_0000 - 0xdfff_ffff.
But Arnd says in that rpc and sa1100 will never have to use the
default since they cannot be part of a multiplatform kernel, and that
is unlikely to change.
Several platforms need MAX_PHYSMEM_BITS >= 36 so we'll pick that as the
minimum. Anything higher and we'll fail the SECTIONS_WIDTH + NODES_WIDTH +
ZONES_WIDTH test in <linux/mm.h>.
Some analysis from Russell King at
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-October/298957.html:
I think this is fine in as far as it goes - this means we end up with
256 entries in the mem_section array which means it occupies one page,
which I think is acceptable overhead.
The other thing to be aware of here is the obvious:
#if (MAX_ORDER - 1 + PAGE_SHIFT) > SECTION_SIZE_BITS
#error Allocator MAX_ORDER exceeds SECTION_SIZE
#endif
Which means that with 28 bits of section, that's a maximum allocator
order of 16. We appear to allow FORCE_MAX_ZONEORDER to be set up to
64 in the case of shmobile, which doesn't seem like a sensible upper
limit - and certainly isn't when sparsemem is enabled.
Given this, I think that FORCE_MAX_ZONEORDER's help, and the
dependencies probably could do with some improvement to make the
issues more transparent.
[gregory.0xf0: added notes from Arnd and Russell]
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many callers either use NULL or const strings for the third argument of
clk_register_clkdev. For those that do not and use a non-const string,
this is a risk for format strings being accidentally processed (for
example in device names). As this interface is already used as if it
weren't a format string (prints nothing when NULL), and there are zero
users of the format strings, remove the format string interface to make
sure format strings will not leak into the clkdev.
$ git grep '\bclk_register_clkdev\b' | grep % | wc -l
0
Unfortunately, all the internals expect a va_list even though they treat
a NULL format string as special. To deal with this, we must pass either
(..., "%s", string) or (..., NULL) so that a the va_list will be created
correctly (passing the name as an argument, not as a format string).
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These two targets were introduced by commit 13d5fadf45 ("[ARM]
Make 'i' and 'zi' targets work") to short-circuit the dependencies
for 'install' and 'zinstall'.
After that, commit 19514fc665 ('arm, kbuild: make "make install"
not depend on vmlinux') eventually made "(z)install" equivalent to
"(z)i".
It is true that 'i' and 'zi' might be still useful as shorthands
but the original intention had been already lost.
They do not even show up in "make ARCH=arm help", so I hope this
deletion does not have much impact.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
"PHONY += FORCE" is already cared by scripts/Makefile.build,
which this file is included from.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARMv8 introduces system registers for the Generic Interrupt Controllers
CPU and virtual interfaces. When GICv3 is implemented, EL2 needs to
allow the kernel to use those registers, by changing the value of
ICC_HSRE.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When rodata is large enough that it crosses a section boundary after the
kernel text, mark the rest NX. This is as close to full NX of rodata as
we can get without splitting page tables or doing section alignment via
CONFIG_DEBUG_ALIGN_RODATA.
When the config is:
CONFIG_DEBUG_RODATA=y
# CONFIG_DEBUG_ALIGN_RODATA is not set
Before:
---[ Kernel Mapping ]---
0x80000000-0x80100000 1M RW NX SHD
0x80100000-0x80a00000 9M ro x SHD
0x80a00000-0xa0000000 502M RW NX SHD
After:
---[ Kernel Mapping ]---
0x80000000-0x80100000 1M RW NX SHD
0x80100000-0x80700000 6M ro x SHD
0x80700000-0x80a00000 3M ro NX SHD
0x80a00000-0xa0000000 502M RW NX SHD
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For an XIP build, _etext does not represent the end of the
binary image that needs to stay mapped into the MODULES_VADDR area.
Years ago, data came before text in the memory map. However,
now that the order is text/init/data, an XIP_KERNEL needs to map
up to the data location in order to keep from cutting off
parts of the kernel that are needed.
We only map up to the beginning of data because data has already been
copied, so there's no reason to keep it around anymore.
A new symbol is created to make it clear what it is we are referring
to.
This fixes the bug where you might lose the end of your kernel area
after page table setup is complete.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit b9b32bf70f ("ARM: use linker magic for vectors and vector stubs")
updated the linker script to emit the .vectors and .stubs sections into a
VMA range that is zero based and disjoint from the normal static kernel
region. The reason for that was that this way, the sections can be placed
exactly 4 KB apart, while the payload of the .vectors section is only 32
bytes.
Since the symbols that are part of the .stubs section are emitted into the
kallsyms table, they appear with zero based addresses as well, e.g.,
00001004 t vector_rst
00001020 t vector_irq
000010a0 t vector_dabt
00001120 t vector_pabt
000011a0 t vector_und
00001220 t vector_addrexcptn
00001240 t vector_fiq
00001240 T vector_fiq_offset
As this confuses perf when it accesses the kallsyms tables, commit
7122c3e915 ("scripts/link-vmlinux.sh: only filter kernel symbols for
arm") implemented a somewhat ugly special case for ARM, where the value
of CONFIG_PAGE_OFFSET is passed to scripts/kallsyms, and symbols whose
addresses are below it are filtered out. Note that this special case only
applies to CONFIG_XIP_KERNEL=n, not because the issue the patch addresses
exists only in that case, but because finding a limit below which to apply
the filtering is not entirely straightforward.
Since the .vectors and .stubs sections contain position independent code
that is never executed in place, we can emit it at its most likely runtime
VMA (for more recent CPUs), which is 0xffff0000 for the vector table and
0xffff1000 for the stubs. Not only does this fix the perf issue with
kallsyms, allowing us to drop the special case in scripts/kallsyms
entirely, it also gives debuggers a more realistic view of the address
space, and setting breakpoints or single stepping through code in the
vector table or the stubs is more likely to work as expected on CPUs that
use a high vector address. E.g.,
00001240 A vector_fiq_offset
...
c0c35000 T __init_begin
c0c35000 T __vectors_start
c0c35020 T __stubs_start
c0c35020 T __vectors_end
c0c352e0 T _sinittext
c0c352e0 T __stubs_end
...
ffff1004 t vector_rst
ffff1020 t vector_irq
ffff10a0 t vector_dabt
ffff1120 t vector_pabt
ffff11a0 t vector_und
ffff1220 t vector_addrexcptn
ffff1240 T vector_fiq
(Note that vector_fiq_offset is now an absolute symbol, which kallsyms
already ignores by default)
The LMA footprint is identical with or without this change, only the VMAs
are different:
Before:
Idx Name Size VMA LMA File off Algn
...
14 .notes 00000024 c0c34020 c0c34020 00a34020 2**2
CONTENTS, ALLOC, LOAD, READONLY, CODE
15 .vectors 00000020 00000000 c0c35000 00a40000 2**1
CONTENTS, ALLOC, LOAD, READONLY, CODE
16 .stubs 000002c0 00001000 c0c35020 00a41000 2**5
CONTENTS, ALLOC, LOAD, READONLY, CODE
17 .init.text 0006b1b8 c0c352e0 c0c352e0 00a452e0 2**5
CONTENTS, ALLOC, LOAD, READONLY, CODE
...
After:
Idx Name Size VMA LMA File off Algn
...
14 .notes 00000024 c0c34020 c0c34020 00a34020 2**2
CONTENTS, ALLOC, LOAD, READONLY, CODE
15 .vectors 00000020 ffff0000 c0c35000 00a40000 2**1
CONTENTS, ALLOC, LOAD, READONLY, CODE
16 .stubs 000002c0 ffff1000 c0c35020 00a41000 2**5
CONTENTS, ALLOC, LOAD, READONLY, CODE
17 .init.text 0006b1b8 c0c352e0 c0c352e0 00a452e0 2**5
CONTENTS, ALLOC, LOAD, READONLY, CODE
...
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit b9b32bf70f ("ARM: use linker magic for vectors and vector stubs")
introduced new global definitions of __vectors_start and __stubs_start,
and changed the existing ones to have internal linkage only. However, these
symbols are still visible to kallsyms, and due to the way the .vectors and
.stubs sections are emitted at the base of the VMA space, these duplicate
definitions have conflicting values.
$ nm -n vmlinux |grep -E __vectors|__stubs
00000000 t __vectors_start
00001000 t __stubs_start
c0e77000 T __vectors_start
c0e77020 T __stubs_start
This is completely harmless by itself, since the wrong values are local
symbols that cannot be referenced by other object files directly. However,
since these symbols are also listed in the kallsyms symbol table in some
cases (i.e., CONFIG_KALLSYMS_ALL=y and CONFIG_XIP_KERNEL=y), having these
conflicting values can be confusing. So either remove them, or make them
strictly local.
Acked-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When building an XIP kernel, the linker script needs to be much different
than a conventional kernel's script. Over time, it's been difficult to
maintain both XIP and non-XIP layouts in one linker script. Therefore,
this patch separates the two procedures into two completely different
files.
The new linker script is essentially a straight copy of the current script
with all the non-CONFIG_XIP_KERNEL portions removed.
Additionally, all CONFIG_XIP_KERNEL portions have been removed from the
existing linker script...never to return again.
It should be noted that this does not fix any current XIP issues, but
rather is the first move in fixing them properly with subsequent patches.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM64 PSCI kernel interfaces that initialize idle states and implement
the suspend API to enter them are generic and can be shared with the
ARM architecture.
To achieve that goal, this patch moves ARM64 PSCI idle management
code to drivers/firmware, so that the interface to initialize and
enter idle states can actually be shared by ARM and ARM64 arches
back-ends.
The ARM generic CPUidle implementation also requires the definition of
a cpuidle_ops section entry for the kernel to initialize the CPUidle
operations at boot based on the enable-method (ie ARM64 has the
statically initialized cpu_ops counterparts for that purpose); therefore
this patch also adds the required section entry on CONFIG_ARM for PSCI so
that the kernel can initialize the PSCI CPUidle back-end when PSCI is
the probed enable-method.
On ARM64 this patch provides no functional change.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> [arch/arm64]
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The code enabled by the ARM_CPU_SUSPEND config option is used by
kernel subsystems for purposes that go beyond system suspend so its
config entry should be augmented to take more default options into
account and avoid forcing its selection to prevent dependencies
override.
To achieve this goal, this patch reworks the ARM_CPU_SUSPEND config
entry and updates its default config value (by adding the BL_SWITCHER
option to it) and its dependencies (ARCH_SUSPEND_POSSIBLE), so that the
symbol is still selected by default by the subsystems requiring it and
at the same time enforcing the dependencies correctly.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
DMA allocations might be subject to certain requirements specific to the
hardware using the buffers, such as availability of kernel mapping (for
contents fix-ups in the driver). The only entity that knows them is the
driver, so it must share this knowledge with vb2-dc.
This patch extends the alloc_ctx initialization interface to let the
driver specify DMA attrs, which are then stored inside the allocation
context and will be used for all allocations with that context.
As a side effect, all dma_*_coherent() calls are turned into
dma_*_attrs() calls, because the attributes need to be carried over
through all DMA operations.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we know that TLB efficiency will not be an issue when memory is
accessed then it's not terribly important to allocate big chunks of
memory. The whole point of allocating the big chunks was that it would
make TLB usage efficient.
As Marek Szyprowski indicated:
Please note that mapping memory with larger pages significantly
improves performance, especially when IOMMU has a little TLB
cache. This can be easily observed when multimedia devices do
processing of RGB data with 90/270 degree rotation
Image rotation is distinctly an operation that needs to bounce around
through memory, so it makes sense that TLB efficiency is important
there.
Video decoding, on the other hand, is a fairly sequential operation.
During video decoding it's not expected that we'll be jumping all over
memory. Decoding video is also pretty heavy and the TLB misses aren't a
huge deal. Presumably most HW video acceleration users of dma-mapping
will not care about huge pages and will set DMA_ATTR_ALLOC_SINGLE_PAGES.
Allocating big chunks of memory is quite expensive, especially if we're
doing it repeadly and memory is full. In one (out of tree) usage model
it is common that arm_iommu_alloc_attrs() is called 16 times in a row,
each one trying to allocate 4 MB of memory. This is called whenever the
system encounters a new video, which could easily happen while the
memory system is stressed out. In fact, on certain social media
websites that auto-play video and have infinite scrolling, it's quite
common to see not just one of these 16x4MB allocations but 2 or 3 right
after another. Asking the system even to do a small amount of extra
work to give us big chunks in this case is just not a good use of time.
Allocating big chunks of memory is also expensive indirectly. Even if
we ask the system not to do ANY extra work to allocate _our_ memory,
we're still potentially eating up all big chunks in the system.
Presumably there are other users in the system that aren't quite as
flexible and that actually need these big chunks. By eating all the big
chunks we're causing extra work for the rest of the system. We also may
start making other memory allocations fail. While the system may be
robust to such failures (as is the case with dwc2 USB trying to allocate
buffers for Ethernet data and with WiFi trying to allocate buffers for
WiFi data), it is yet another big performance hit.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the DMA_ATTR_ALLOC_SINGLE_PAGES attribute to the
DMA-mapping subsystem.
This attribute can be used as a hint to the DMA-mapping subsystem that
it's likely not worth it to try to allocate large pages behind the
scenes. Large pages are likely to make an IOMMU TLB work more
efficiently but may not be worth it. See the Documentation contained in
this patch for more details about this attribute and when to use it.
Note that the name of the hint (DMA_ATTR_ALLOC_SINGLE_PAGES) is loosely
based on the name MADV_NOHUGEPAGE. Just as there is MADV_NOHUGEPAGE
vs. MADV_HUGEPAGE we could also add an "opposite" attribute to
DMA_ATTR_ALLOC_SINGLE_PAGES. Without having the "opposite" attribute
the lack of DMA_ATTR_ALLOC_SINGLE_PAGES means "use your best judgement
about whether to use small pages or large pages".
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The __iommu_alloc_buffer() is expected to be called to allocate pretty
sizeable buffers. Upon simple tests of video I saw it trying to
allocate 4,194,304 bytes. The function tries to allocate large chunks
in order to optimize IOMMU TLB usage.
The current function is very, very slow.
One problem is the way it keeps trying and trying to allocate big
chunks. Imagine a very fragmented memory that has 4M free but no
contiguous pages at all. Further imagine allocating 4M (1024 pages).
We'll do the following memory allocations:
- For page 1:
- Try to allocate order 10 (no retry)
- Try to allocate order 9 (no retry)
- ...
- Try to allocate order 0 (with retry, but not needed)
- For page 2:
- Try to allocate order 9 (no retry)
- Try to allocate order 8 (no retry)
- ...
- Try to allocate order 0 (with retry, but not needed)
- ...
- ...
Total number of calls to alloc() calls for this case is:
sum(int(math.log(i, 2)) + 1 for i in range(1, 1025))
=> 9228
The above is obviously worse case, but given how slow alloc can be we
really want to try to avoid even somewhat bad cases. I timed the old
code with a device under memory pressure and it wasn't hard to see it
take more than 120 seconds to allocate 4 megs of memory! (NOTE: testing
was done on kernel 3.14, so possibly mainline would behave
differently).
A second problem is that allocating big chunks under memory pressure
when we don't need them is just not a great idea anyway unless we really
need them. We can make due pretty well with smaller chunks so it's
probably wise to leave bigger chunks for other users once memory
pressure is on.
Let's adjust the allocation like this:
1. If a big chunk fails, stop trying to hard and bump down to lower
order allocations.
2. Don't try useless orders. The whole point of big chunks is to
optimize the TLB and it can really only make use of 2M, 1M, 64K and
4K sizes.
We'll still tend to eat up a bunch of big chunks, but that might be the
right answer for some users. A future patch could possibly add a new
DMA_ATTR that would let the caller decide that TLB optimization isn't
important and that we should use smaller chunks. Presumably this would
be a sane strategy for some callers.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The tmp variable is used twice: first to pose as a register containing
a value of zero, and then to provide a temporary register that initially
is zero and get added some value. But somehow gcc decides to split those
two usages in different registers.
Example code:
u64 div64const1000(u64 x)
{
u32 y = 1000;
do_div(x, y);
return x;
}
Result:
div64const1000:
push {r4, r5, r6, r7, lr}
mov lr, #0
mov r6, r0
mov r7, r1
adr r5, .L8
ldrd r4, [r5]
mov r1, lr
umull r2, r3, r4, r6
cmn r2, r4
adcs r3, r3, r5
adc r2, lr, #0
umlal r3, r2, r5, r6
umlal r3, r1, r4, r7
mov r3, #0
adds r2, r1, r2
adc r3, r3, #0
umlal r2, r3, r5, r7
lsr r0, r2, #9
lsr r1, r3, #9
orr r0, r0, r3, lsl #23
pop {r4, r5, r6, r7, pc}
.align 3
.L8:
.word -1924145349
.word -2095944041
Full kernel build size:
text data bss dec hex filename
13663814 1553940 351368 15569122 ed90e2 vmlinux
Here the two instances of 'tmp' are assigned to r1 and lr.
To avoid that, let's mark the first 'tmp' usage in __arch_xprod_64()
with a "+r" constraint even if the register is not written to, so to
create a dependency for the second usage with the effect of enforcing
a single temporary register throughout.
Result:
div64const1000:
push {r4, r5, r6, r7}
movs r3, #0
adr r5, .L8
ldrd r4, [r5]
umull r6, r7, r4, r0
cmn r6, r4
adcs r7, r7, r5
adc r6, r3, #0
umlal r7, r6, r5, r0
umlal r7, r3, r4, r1
mov r7, #0
adds r6, r3, r6
adc r7, r7, #0
umlal r6, r7, r5, r1
lsr r0, r6, #9
lsr r1, r7, #9
orr r0, r0, r7, lsl #23
pop {r4, r5, r6, r7}
bx lr
.align 3
.L8:
.word -1924145349
.word -2095944041
text data bss dec hex filename
13663438 1553940 351368 15568746 ed8f6a vmlinux
This time 'tmp' is assigned to r3 and used throughout. However, by being
assigned to r3, that blocks usage of the r2-r3 double register slot for
64-bit values, forcing more registers to be spilled on the stack. Let's
try to help it by forcing 'tmp' to the caller-saved ip register.
Result:
div64const1000:
stmfd sp!, {r4, r5}
mov ip, #0
adr r5, .L8
ldrd r4, [r5]
umull r2, r3, r4, r0
cmn r2, r4
adcs r3, r3, r5
adc r2, ip, #0
umlal r3, r2, r5, r0
umlal r3, ip, r4, r1
mov r3, #0
adds r2, ip, r2
adc r3, r3, #0
umlal r2, r3, r5, r1
mov r0, r2, lsr #9
mov r1, r3, lsr #9
orr r0, r0, r3, asl #23
ldmfd sp!, {r4, r5}
bx lr
.align 3
.L8:
.word -1924145349
.word -2095944041
text data bss dec hex filename
13662838 1553940 351368 15568146 ed8d12 vmlinux
We could make the code marginally smaller yet by forcing 'tmp' to lr
instead, but that would have a negative inpact on branch prediction for
which "bx lr" is optimal.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The use of CONFIG_DEBUG_RODATA is generally seen as an essential part of
kernel self-protection:
http://www.openwall.com/lists/kernel-hardening/2015/11/30/13
Additionally, its name has grown to mean things beyond just rodata. To
get ARM closer to this, we ought to rearrange the names of the configs
that control how the kernel protects its memory. What was called
CONFIG_ARM_KERNMEM_PERMS is realy doing the work that other architectures
call CONFIG_DEBUG_RODATA.
This redefines CONFIG_DEBUG_RODATA to actually do the bulk of the
ROing (and NXing). In the place of the old CONFIG_DEBUG_RODATA, use
CONFIG_DEBUG_ALIGN_RODATA, since that's what the option does: adds
section alignment for making rodata explicitly NX, as arm does not split
the page tables like arm64 does without _ALIGN_RODATA.
Also adds human readable names to the sections so I could more easily
debug my typos, and makes CONFIG_DEBUG_RODATA default "y" for CPU_V7.
Results in /sys/kernel/debug/kernel_page_tables for each config state:
# CONFIG_DEBUG_RODATA is not set
# CONFIG_DEBUG_ALIGN_RODATA is not set
---[ Kernel Mapping ]---
0x80000000-0x80900000 9M RW x SHD
0x80900000-0xa0000000 503M RW NX SHD
CONFIG_DEBUG_RODATA=y
CONFIG_DEBUG_ALIGN_RODATA=y
---[ Kernel Mapping ]---
0x80000000-0x80100000 1M RW NX SHD
0x80100000-0x80700000 6M ro x SHD
0x80700000-0x80a00000 3M ro NX SHD
0x80a00000-0xa0000000 502M RW NX SHD
CONFIG_DEBUG_RODATA=y
# CONFIG_DEBUG_ALIGN_RODATA is not set
---[ Kernel Mapping ]---
0x80000000-0x80100000 1M RW NX SHD
0x80100000-0x80a00000 9M ro x SHD
0x80a00000-0xa0000000 502M RW NX SHD
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Code run via soft_restart() is run with the MMU disabled, so we need to
pass the identity map physical address rather than the address obtained
from virt_to_phys(). Therefore, replace virt_to_phys() with
virt_to_idmap() for all callers of soft_restart().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make virt_to_idmap() return an unsigned long rather than phys_addr_t.
Returning phys_addr_t here makes no sense, because the definition of
virt_to_idmap() is that it shall return a physical address which maps
identically with the virtual address. Since virtual addresses are
limited to 32-bit, identity mapped physical addresses are as well.
Almost all users already had an implicit narrowing cast to unsigned long
so let's make this official and part of this interface.
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arm: irq: l2c: do not print error in case of missing l2c from dtb
In some architectures the L2 cache controller is integrated in the
processor's block itself and it doesn't use any external cache
controller. This means that an entry in the board's dtb related
to the l2c is not necessary.
Distinguish between error codes and do not print anything in case
l2x0_of_init() doesn't find any L2C DTB entry and returns -ENODEV.
This patch mutes the following error message:
L2C: failed to init: -19
on boards like odroid-xu4, cortex A7/A15, which don't have
external cache controller.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Instead of looping through all cpus calling set_capacity_scale, we can
initialise cpu_scale per-cpu variables to SCHED_CAPACITY_SCALE with their
definition.
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement an ARM delay timer to be used for udelay() on orion legacy
platforms. This allows us to skip the delay loop calibration at boot.
It also means that udelay() will be unaffected by CPU frequency changes
when cpufreq is enabled on these platforms.
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
A build warning fix, MAINTAINERS cleanup, and a new DMI quirk.
ideapad-laptop:
- Add Lenovo Yoga 700 to no_hw_rfkill dmi list
MAINTAINERS:
- Combine multiple telemetry entries
intel_telemetry_debugfs:
- Fix unused warnings in telemetry debugfs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWpRa0AAoJEKbMaAwKp364T3EIAK09qgxu5q8tfW/kuD2GdPu5
uJgoqf0W5bVVnIiUixlQ1r7aK5SiQtWAc/Flj4yAamqO3YxjPl9Z6jFr4PGMHjCp
wPr6lz9H1KupN8OZd4rgYr3MpGj8SKEFm/7+swfbZvACxaaxippYDjmdYUu5l7JJ
RRfWnxc7E5RLiDhPoxAR4cJ5kJgir1Iv78On8Vt1dDWl23odGBTilGCpCXoEifUZ
6YOKF29VoVxhJBW35Mb3qXMMyYDnQzTpDKKVO8f/UCj63bD2io5YWb+Ur3Tz5YCv
Bn+DWMTIxmLDHRUVRTwHCh9zE3RpsfMcbEsUXt/bm/cbGfWOSo2eQRVBAAIqjA0=
=EAaK
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Emergency travel prevented me from completing my final testing on this
until today. Nothing here that couldn't wait until RC1 fixes, but I
thought it best to get it out sooner rather than later as it does
contain a build warning fix.
Summary:
A build warning fix, MAINTAINERS cleanup, and a new DMI quirk:
ideapad-laptop:
- Add Lenovo Yoga 700 to no_hw_rfkill dmi list
MAINTAINERS:
- Combine multiple telemetry entries
intel_telemetry_debugfs:
- Fix unused warnings in telemetry debugfs"
* tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
MAINTAINERS: Combine multiple telemetry entries
intel_telemetry_debugfs: Fix unused warnings in telemetry debugfs
Pull thermal management updates from Zhang Rui:
"The top merge commit was re-generated yesterday because two topic
branches were dropped from this pull request in the last minute due to
some unaddressed comments. All the other material has been in
linux-next for quite a while.
Specifics:
- Enhance thermal core to handle unexpected device cooling states
after fresh boot and system resume. From Zhang Rui and Chen Yu.
- Several fixes and cleanups on Rockchip and RCAR thermal drivers.
From Caesar Wang and Kuninori Morimoto.
- Add Broxton support for Intel processor thermal reporting device
driver. From Amy Wiles"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: trip_point_temp_store() calls thermal_zone_device_update()
thermal: rcar: rcar_thermal_get_temp() return error if strange temp
thermal: rcar: check irq possibility in rcar_thermal_irq_xxx()
thermal: rcar: check every rcar_thermal_update_temp() return value
thermal: rcar: move rcar_thermal_dt_ids to upside
thermal: rockchip: Support the RK3399 SoCs in thermal driver
thermal: rockchip: Support the RK3228 SoCs in thermal driver
dt-bindings: rockchip-thermal: Support the RK3228/RK3399 SoCs compatible
thermal: rockchip: fix a trivial typo
Thermal: Enable Broxton SoC thermal reporting device
thermal: constify pch_dev_ops structure
Thermal: do thermal zone update after a cooling device registered
Thermal: handle thermal zone device properly during system sleep
Thermal: initialize thermal zone device correctly
-----BEGIN PGP SIGNATURE-----
Comment: GPGTools - http://gpgtools.org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=32IE
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
Pull 9p updates from Eric Van Hensbergen:
"Sorry for the last minute pull request, there's was a change that
didn't get pulled into for-next until two weeks ago and I wanted to
give it some bake time.
Summary:
Rework and error handling fixes, primarily in the fscatch and fd
transports"
* tag 'for-linus-4.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
fs/9p: use fscache mutex rather than spinlock
9p: trans_fd, bail out if recv fcall if missing
9p: trans_fd, read rework to use p9_parse_header
net/9p: Add device name details on error
Pull Ceph updates from Sage Weil:
"The two main changes are aio support in CephFS, and a series that
fixes several issues in the authentication key timeout/renewal code.
On top of that are a variety of cleanups and minor bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: remove outdated comment
libceph: kill off ceph_x_ticket_handler::validity
libceph: invalidate AUTH in addition to a service ticket
libceph: fix authorizer invalidation, take 2
libceph: clear messenger auth_retry flag if we fault
libceph: fix ceph_msg_revoke()
libceph: use list_for_each_entry_safe
ceph: use i_size_{read,write} to get/set i_size
ceph: re-send AIO write request when getting -EOLDSNAP error
ceph: Asynchronous IO support
ceph: Avoid to propagate the invalid page point
ceph: fix double page_unlock() in page_mkwrite()
rbd: delete an unnecessary check before rbd_dev_destroy()
libceph: use list_next_entry instead of list_entry_next
ceph: ceph_frag_contains_value can be boolean
ceph: remove unused functions in ceph_frag.h
Pull SMB3 fixes from Steve French:
"A collection of CIFS/SMB3 fixes.
It includes a couple bug fixes, a few for improved debugging of
cifs.ko and some improvements to the way cifs does key generation.
I do have some additional bug fixes I expect in the next week or two
(to address a problem found by xfstest, and some fixes for SMB3.11
dialect, and a couple patches that just came in yesterday that I am
reviewing)"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs_dbg() outputs an uninitialized buffer in cifs_readdir()
cifs: fix race between call_async() and reconnect()
Prepare for encryption support (first part). Add decryption and encryption key generation. Thanks to Metze for helping with this.
cifs: Allow using O_DIRECT with cache=loose
cifs: Make echo interval tunable
cifs: Check uniqueid for SMB2+ and return -ESTALE if necessary
Print IP address of unresponsive server
cifs: Ratelimit kernel log messages
Like the Yoga 900 models the Lenovo Yoga 700 does not have a
hw rfkill switch, and trying to read the hw rfkill switch through the
ideapad module causes it to always reported blocking breaking wifi.
This commit adds the Lenovo Yoga 700 to the no_hw_rfkill dmi list, fixing
the wifi breakage.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1295272
Tested-by: <dinyar.rabady+spam@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch combines all the telemetry file entries in MAINTAINERS via
wildcard.
Signed-off-by: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch fixes compile time warnings when CONFIG_PM_SLEEP
is undefined. In this case sleep related counters are unused.
Signed-off-by: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
If we detect that there is nothing to do just set the flag and do not
check if it was already set before. Races really do not matter. If the
flag is set by any code then the shepherd will start dealing with the
situation and reenable the vmstat workers when necessary again.
Since commit 0eb77e9880 ("vmstat: make vmstat_updater deferrable again
and shut down on idle") quiet_vmstat might update cpu_stat_off and mark
a particular cpu to be handled by vmstat_shepherd. This might trigger a
VM_BUG_ON in vmstat_update because the work item might have been
sleeping during the idle period and see the cpu_stat_off updated after
the wake up. The VM_BUG_ON is therefore misleading and no more
appropriate. Moreover it doesn't really suite any protection from real
bugs because vmstat_shepherd will simply reschedule the vmstat_work
anytime it sees a particular cpu set or vmstat_update would do the same
from the worker context directly. Even when the two would race the
result wouldn't be incorrect as the counters update is fully idempotent.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As most platforms implement the PROM serial interface prom_putchar()
add a simple bridge to allow re-using this code for zboot.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11811/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add dummy.o to the targets list, and fill targets automatically from
$(vmlinuzobjs) to avoid having to maintain two lists.
When building with XZ compression copy ashldi3.c to the build
directory to use a different object file for the kernel and zboot.
Without this the same object file need to be build with different
flags which cause a rebuild at every run.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11810/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove bcm63xx_nvram_get_psi_size() as it now has no users.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11836/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The "dual_image" and "inactive_flag" fields should be merged into a single
"image_sequence" field.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11834/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The extended flash address needs to be subtracted from bcm_tag flash
image offsets. Move this value to the bcm_tag header file.
Renamed define name to consistently use bcm963xx for flash layout
which should be considered a property of the board and not the SoC
(i.e. bcm63xx could theoretically be used on a board without CFE
or any flash).
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11833/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move Broadcom BCM963xx image tag data structure to include/linux/
so that drivers outside of mach-bcm63xx can use it.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11832/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the common definition of the nvram structure from the header file
include/linux/bcm963xx_nvram.h instead of maintaining a separate copy.
Read the version 5 size of nvram data from memory and then call the
new checksum verification function from the header file.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11831/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Broadcom BCM963xx boards have multiple nvram variants across different
SoCs with additional checksum fields added whenever the size of the
nvram was extended.
Add this structure as a header file so that multiple drivers can use it.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11830/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Remove usage of ib_query_device and instead store attributes in
ib_device struct
- Move iopoll out of block and into lib, rename to irqpoll, and use
in several places in the rdma stack as our new completion queue
polling library mechanism. Update the other block drivers that
already used iopoll to use the new mechanism too.
- Replace the per-entry GID table locks with a single GID table lock
- IPoIB multicast cleanup
- Cleanups to the IB MR facility
- Add support for 64bit extended IB counters
- Fix for netlink oops while parsing RDMA nl messages
- RoCEv2 support for the core IB code
- mlx4 RoCEv2 support
- mlx5 RoCEv2 support
- Cross Channel support for mlx5
- Timestamp support for mlx5
- Atomic support for mlx5
- Raw QP support for mlx5
- MAINTAINERS update for mlx4/mlx5
- Misc ocrdma, qib, nes, usNIC, cxgb3, cxgb4, mlx4, mlx5 updates
- Add support for remote invalidate to the iSER driver (pushed through the
RDMA tree due to dependencies, acknowledged by nab)
- Update to NFSoRDMA (pushed through the RDMA tree due to dependencies,
acknowledged by Bruce)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5oO7
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Initial roundup of 4.5 merge window patches
- Remove usage of ib_query_device and instead store attributes in
ib_device struct
- Move iopoll out of block and into lib, rename to irqpoll, and use
in several places in the rdma stack as our new completion queue
polling library mechanism. Update the other block drivers that
already used iopoll to use the new mechanism too.
- Replace the per-entry GID table locks with a single GID table lock
- IPoIB multicast cleanup
- Cleanups to the IB MR facility
- Add support for 64bit extended IB counters
- Fix for netlink oops while parsing RDMA nl messages
- RoCEv2 support for the core IB code
- mlx4 RoCEv2 support
- mlx5 RoCEv2 support
- Cross Channel support for mlx5
- Timestamp support for mlx5
- Atomic support for mlx5
- Raw QP support for mlx5
- MAINTAINERS update for mlx4/mlx5
- Misc ocrdma, qib, nes, usNIC, cxgb3, cxgb4, mlx4, mlx5 updates
- Add support for remote invalidate to the iSER driver (pushed
through the RDMA tree due to dependencies, acknowledged by nab)
- Update to NFSoRDMA (pushed through the RDMA tree due to
dependencies, acknowledged by Bruce)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (169 commits)
IB/mlx5: Unify CQ create flags check
IB/mlx5: Expose Raw Packet QP to user space consumers
{IB, net}/mlx5: Move the modify QP operation table to mlx5_ib
IB/mlx5: Support setting Ethernet priority for Raw Packet QPs
IB/mlx5: Add Raw Packet QP query functionality
IB/mlx5: Add create and destroy functionality for Raw Packet QP
IB/mlx5: Refactor mlx5_ib_qp to accommodate other QP types
IB/mlx5: Allocate a Transport Domain for each ucontext
net/mlx5_core: Warn on unsupported events of QP/RQ/SQ
net/mlx5_core: Add RQ and SQ event handling
net/mlx5_core: Export transport objects
IB/mlx5: Expose CQE version to user-space
IB/mlx5: Add CQE version 1 support to user QPs and SRQs
IB/mlx5: Fix data validation in mlx5_ib_alloc_ucontext
IB/sa: Fix netlink local service GFP crash
IB/srpt: Remove redundant wc array
IB/qib: Improve ipoib UD performance
IB/mlx4: Advertise RoCE v2 support
IB/mlx4: Create and use another QP1 for RoCEv2
IB/mlx4: Enable send of RoCE QP1 packets with IP/UDP headers
...
I've pretty much been maintaining KVM for MIPS for a while now. Lets
make it more official (and make sure I get Cc'd on relevant patches).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11898/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The header arch/mips/kvm/opcode.h defines a few extra opcodes which
aren't in arch/mips/include/uapi/asm/inst.h. There's nothing KVM
specific about them, so lets move them into inst.h where they belong and
delete the header.
Note that mfmcz_op is renamed to mfmc0_op to match the instruction set
manual, and wait_op was already added to inst.h in commit b0a3eae2b9
("MIPS: inst.h: define COP0 wait op"), merged in v3.16-rc1.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11895/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Drop the custom cache operation code definitions used by KVM for
emulating guest CACHE instructions, and switch to use the existing
definitions in <asm/cacheops.h>.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11893/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nicolas Pitre