From the indenting, it seems like the READ_NEXT_PAIR() was supposed to
be inside the while loop.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The # flag in %X means print a 0X prefix. Remove the extra 0x prefix.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to add per-vif TX power capability cap per-packet TX power to vif
configured power if the latter is lower than per-rate TX power and mac80211
per-frame power. Use vif TX power if TPC has been disabled for current the
interface
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure the HW with highest TX power among all vif when HW TPC has been
enabled in order to add support to per-vif TX power capability. Use lowest
configured power among all interfaces when TPC is disabled
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HAL_RETRY_LIMIT_*
RESET_DELAY_8185
RT_IBSS_INT_MASKS
RT_AC_INT_MASKS
NUM_OF_*
BT_*,
MAX_{LINES,BYTES}_*,
*_THREE_WIRE
*_QUEUE related
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
kbuild found out that commit 804e27dee4 ("bcma: support bringing up
bus hosted on PCIe Gen 2") broke the build on m68k:
drivers/bcma/driver_pcie2.c: In function 'bcma_core_pcie2_up':
>> drivers/bcma/driver_pcie2.c:196:2: error: implicit declaration of function 'pcie_set_readrq' [-Werror\
=implicit-function-declaration]
err = pcie_set_readrq(dev, pcie2->reqsize);
^
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set The BT/WLAN priority weights correctly and make sure
that MCI_LNA_TAKE is sent only for cards that share
PA/LNA.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Handle MCI_STATE_INIT_GPM_OFFSET separately and do not
overload ar9003_mci_get_next_gpm_offset() with a special
case.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The LNA_TRANS message needs to be sent only for
chips which have shared PA/LNA.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use a subroutine to enable MCI debug statistics
if it is present in the global configuration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch makes sure that the antenna configuration
is used properly when setting AR_MCI_TX_CTRL.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The value programmed in the BTCOEX control register
is different for each chip. This patch adds support
for 2-ANT, 1-ANT solutions based on AR9565.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Several new MCI parameters need to be handled for
new chips, add them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we fail to allocate the sched/gpm buffers when
initializing MCI, we bail out properly. Checking
them in ar9003_mci_reset() is unnecessary, so remove it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* remove support for -9.ucode
* new statitics API
* rate control improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uonl
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-03-01' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* add triggers for firmware dump collection
* remove support for -9.ucode
* new statitics API
* rate control improvements
Bump i40e to 1.2.10 and i40evf to 1.2.4
Change-ID: I48aa64df05fcc8356e7026f3a9e69ecf78d0c785
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case of MFP mode the driver was returning incorrect number of TCs
for partitions that are not enabled for iSCSI. Though the driver does
not configure these TCs in the Tx scheduler for the NIC partitions;
it does use this map to setup the queue mappings.
This patch fixes this and keeps all the NIC partitions to the default
PF TC i.e. TC0.
Change-ID: Iede214c907e7bac1356e999049b9f642759512b3
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow DCBNL operations in MFP mode to allow query of port DCB settings
via all the PFs and register iSCSI APP on iSCSI enabled PF.
Change-ID: I34cc39b4665d0a631847d4079350d3814f02381e
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an extra check to make sure that the indirection table pointer is
valid before dereferencing it.
Change-ID: I698adbf3daff03081d01f489dc95a9f1ad8b12f1
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With changes to default number of queue pairs that the interface comes up with
from 1 per online CPU to 1 per lan_msix, we need to make sure we recalculate
rss_size. We will now recalculate rss_size based on number of queues enabled in
the VSI.
Without this fix if the max_lan_msix < num_online_cpu we will be coming up
with fewer queues but will be populating rss_size based on num_online_cpus.
This will result in packets getting silently dropped because RSS LUT has queues
that are not enabled.
Change-ID: Ifac8796ce1be1758bb0c34f38dbf4a3a76621e76
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since all VSIs don't have the same RSS table size,
have one for each VSI instead of having a single define
for RSS table size
Change-ID: Ic2c7c66e4a389d4b6c8841a707510a9735041f02
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were missing a few packet types for VXLAN offload. This patch fixes
that.
Change-ID: I4b23aa0b08e40ed49d0df6c49a5ed9f2009b44ce
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where the driver is not flushing out the
DCBNL app table for applications that are not present in the local
DCBX application configuration TLVs.
Change-ID: I1f1ee04c81c145071b2ab15657546eb10b81fadb
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For FW < 4.33 DCB should be disabled.
Also Autoneg workaround to avoid Rx stall is still needed for FW < 4.33.
Change-ID: Iff36ad86be2f597e7701096014d6d094332a9a21
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When running in a single TC mode the HW can be configured to enable more
than max RSS qps for the Main VSI. This patch makes it possible to
enable as many as num_online_cpus().
ethtool -L can still be used to reconfigure number of qps
to a smaller value.
Change-ID: I3e2df085276982603d86dfd79477c0ada8d30b8f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we now have functionality to enable and disable PF loopback at
runtime, don't try to do it automatically. Removing this call also gets
rid of a bogus error message when removing the PF module with VFs
enabled.
Change-ID: Ic38652d8a3b9498d96113bfaa5ea7bad050862e9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds default case to handle unmatched switch calls.
Change-ID: Icd203570a1dc5322c1038f68b98a83195e8ad28c
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Include the FW build number in the formatted FW version string. In order
to fit within ethtool's 32 character limit, the etrack's unused high order
bits are trimmed as is the leading 0 for the NVM version. This leaves
us with 2 character left for if/when the etrack id goes to 5 hex chars
and the NVM major number goes to 2 chars.
Change-ID: Icb004c4b9b14a2f54dd200b467fcc1d7b9297308
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If DCB is not enabled priority tagging is not needed
so skip over that section.
Change-ID: Ia3f3fa07945b421259a9ca38329d6d1cbd6c6bcc
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a few silly typos in the code and checkpatch warnings in support of
general code cleanliness.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The introduction of ndo_features_check allows drivers to report their
offload capabilities per-skb. Implement this in fm10k to take advantage
of this new functionality.
Reported-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The FM10000 host interface can only support up to 184 bytes when
performing tunnel offloads. Because of this, a check was added to
prevent the driver from attempting to feed a header to the hardware too
big for it to parse. Make this check a little more robust by calculating
the inner L4 header length based on whether it is TCP or UDP.
Cc: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If an over-MTU UDP datagram is sent through a SOCK_RAW socket to a
UFO-capable device, ip_ufo_append_data() sets skb->ip_summed to
CHECKSUM_PARTIAL unconditionally as all GSO code assumes transport layer
checksum is to be computed on segmentation. However, in this case,
skb->csum_start and skb->csum_offset are never set as raw socket
transmit path bypasses udp_send_skb() where they are usually set. As a
result, driver may access invalid memory when trying to calculate the
checksum and store the result (as observed in virtio_net driver).
Moreover, the very idea of modifying the userspace provided UDP header
is IMHO against raw socket semantics (I wasn't able to find a document
clearly stating this or the opposite, though). And while allowing
CHECKSUM_NONE in the UFO case would be more efficient, it would be a bit
too intrusive change just to handle a corner case like this. Therefore
disallowing UFO for packets from SOCK_DGRAM seems to be the best option.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
Fixes for sh_eth #4 v2
I'm continuing review and testing of Ethernet support on the R-Car H2
chip, with help from a colleague. This series fixes a few more issues.
These are not tested on any of the other supported chips.
v2: Add note that the revert is not a pure revert.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
My previous fix to clear padding of short frames used skb->len as the
DMA length, assuming that skb_padto() extended skb->len to include the
padding. That isn't the case; we need to use skb_put_padto() instead.
(This wasn't immediately obvious because software padding isn't
actually needed on the R-Car H2. We could make it conditional on
which chip is being driven, but it's probably not worth the effort.)
Reported-by: "Violeta Menéndez González" <violeta.menendez@codethink.co.uk>
Fixes: 612a17a54b50 ("sh_eth: Fix padding of short frames on TX")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit fd9af07c34.
The hardware manual states that the frame error and multicast bits are
copied to bits 9:0 of RD0, not bits 25:16. I've tested that this is
true for RFS1 (CRC error), RFS3 (frame too short), RFS4 (frame too
long) and RFS8 (multicast).
Also adjust a comment to agree with this.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of RX ring underrun (RDE), we attempt to reset the software
descriptor pointers (dirty_rx and cur_rx) to match where the hardware
will read the next descriptor from, as that might not be the first
dirty descriptor. This relies on reading RDFAR, but that register
doesn't exist on all supported chips - specifically, not on the R-Car
chips. This will result in unpredictable behaviour on those chips
after an RDE.
Make this pointer reset conditional and assume that it isn't needed on
the R-Car chips. This fix also assumes that RDFAR is never exposed at
offset 0 in the memory map - this is currently true, and a subsequent
commit will fix the ambiguity between offset 0 and no-offset in the
register offset maps.
Fixes: 79fba9f517 ("net: sh_eth: fix the rxdesc pointer when rx ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When submitting a DMA descriptor, the active bit must be written last.
When reading a completed DMA descriptor, the active bit must be read
first.
Add memory barriers to ensure that this ordering is maintained.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix a translation problem in of_get_named_gpiod_flags()
- Fix a long standing container_of() mistake in the TPS65912
driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5nhV
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Two GPIO fixes:
- Fix a translation problem in of_get_named_gpiod_flags()
- Fix a long standing container_of() mistake in the TPS65912 driver"
* tag 'gpio-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tps65912: fix wrong container_of arguments
gpiolib: of: allow of_gpiochip_find_and_xlate to find more than one chip per node
Pull thermal management fixes from Eduardo Valentin:
"Specifics:
- Several fixes in tmon tool.
- Fixes in intel int340x for _ART and _TRT tables.
- Add id for Avoton SoC into powerclamp driver.
- Fixes in RCAR thermal driver to remove race conditions and fix fail
path
- Fixes in TI thermal driver: removal of unnecessary code and build
fix if !CONFIG_PM_SLEEP
- Cleanups in exynos thermal driver
- Add stubs for include/linux/thermal.h. Now drivers using thermal
calls but that also work without CONFIG_THERMAL will be able to
compile for systems that don't care about thermal.
Note: I am sending this pull on Rui's behalf while he fixes issues in
his Linux box"
* 'fixes-for-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: int340x_thermal: Ignore missing _ART, _TRT tables
thermal/intel_powerclamp: add id for Avoton SoC
tools/thermal: tmon: silence 'set but not used' warnings
tools/thermal: tmon: use pkg-config to determine library dependencies
tools/thermal: tmon: support cross-compiling
tools/thermal: tmon: add .gitignore
tools/thermal: tmon: fixup tui windowing calculations
tools/thermal: tmon: tui: don't hard-code dialog window size assumptions
tools/thermal: tmon: add min/max macros
tools/thermal: tmon: add --target-temp parameter
thermal: exynos: Clean-up code to use oneline entry for exynos compatible table
thermal: rcar: Make error and remove paths symmetrical with init
thermal: rcar: Fix race condition between init and interrupt
thermal: Introduce dummy functions when thermal is not defined
ti-soc-thermal: Delete an unnecessary check before the function call "cpufreq_cooling_unregister"
thermal: ti-soc-thermal: bandgap: Fix build warning if !CONFIG_PM_SLEEP
- fix a read-balance problem that was reported 2 years ago, but
that I never noticed the report :-(
- fix for rare RAID6 problem causing incorrect bitmap updates when
two devices fail.
- add __ATTR_PREALLOC annotation now that it is possible.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CaGN
-----END PGP SIGNATURE-----
Merge tag 'md/4.0-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Three md fixes:
- fix a read-balance problem that was reported 2 years ago, but that
I never noticed the report :-(
- fix for rare RAID6 problem causing incorrect bitmap updates when
two devices fail.
- add __ATTR_PREALLOC annotation now that it is possible"
* tag 'md/4.0-fixes' of git://neil.brown.name/md:
md: mark some attributes as pre-alloc
raid5: check faulty flag for array status during recovery.
md/raid1: fix read balance when a drive is write-mostly.
This is just a single patch to fix the KSTK_EIP() and KSTK_ESP() macros
for metag which have always been erronously returning the PC and stack
pointer of the task's kernel context rather than from its user context
saved at entry from userland into the kernel, which affects the contents
of /proc/<pid>/maps and /proc/<pid>/stat.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1+sf
-----END PGP SIGNATURE-----
Merge tag 'metag-fixes-v4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull arch/metag fix from James Hogan:
"This is just a single patch to fix the KSTK_EIP() and KSTK_ESP()
macros for metag which have always been erronously returning the PC
and stack pointer of the task's kernel context rather than from its
user context saved at entry from userland into the kernel, which
affects the contents of /proc/<pid>/maps and /proc/<pid>/stat"
* tag 'metag-fixes-v4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: Fix KSTK_EIP() and KSTK_ESP() macros
