RDS iWarp support code has become stale and non testable. As
indicated earlier, am dropping the support for it.
If new iWarp user(s) shows up in future, we can adapat the RDS IB
transprt for the special RDMA READ sink case. iWarp needs an MR
for the RDMA READ sink.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
qed: update series
This patch series tries to improve general configuration by changing
configuration to better suit B0 boards and allow more available
resources to each physical function.
In additition, it contains some small fixes and semantic changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of problems when initializing the chip, the error flows aren't
being properly done. Specifically, it's possible that the chip would be
left in a configuration allowing it [internally] to access the host
memory, causing fatal problems in the device that would require power
cycle to overcome.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current statistics logic is meant for L2, not for all future protocols.
Move this content to the proper designated file.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BB_A0 is a development model that is will not reach actual clients.
In fact, future firmware would simply fail to initialize such chip.
This changes the configuration into B0 instead of A0, and adds a safeguard
against the slim chance someone would actually try this with an A0 adapter
in which case probe would gracefully fail.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver learns the inner bar sized from a register configured by management
firmware, but older versions are not setting this register.
But since we know which values were configured back then, use them instead.
Signed-off-by: Ram Amrani <Ram.Amrani@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls cfg80211_get_station, which may be part of a
module, so we must not enable BATMAN_ADV_BATMAN_V if
BATMAN_ADV=y and CFG80211=m:
net/built-in.o: In function `batadv_v_elp_get_throughput':
(text+0x5c62c): undefined reference to `cfg80211_get_station'
This clarifies the dependency to cover all combinations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c833484e5f ("batman-adv: ELP - compute the metric based on the estimated throughput")
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use managed resource functions devm_kzalloc and pcim_enable_device
to simplify error handling. Subsequently, remove unnecessary
kfree, pci_disable_device and pci_release_regions.
To be compatible with the change, various gotos are replaced with
direct returns and unneeded labels are dropped.
Also, `sc` was only being freed in the probe function and not the
remove function before the change. By using devm_kzalloc this patch
also fixes this memory leak.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
B.A.T.M.A.N. V. Its implementation started quite some years ago,
but due to the big changes being introduced it took a while to be
discussed, designed, worked, re-worked, tested and debugged (well,
we're never done with the latest). The entire operation has
basically been a team work involving all the core contributors
together with other people interested in the project.
The new protocol is divided into two main subcomponents, called
respectively ELP and OGMv2. The former is in charge of
dealing with the neighbour discovery and link quality estimation,
while the latter implements the algorithm that spreads the
metrics around the network and computes optimal paths.
The biggest change introduced with B.A.T.M.A.N. V is the new
metric: the protocol won't rely on packet loss anymore, but it
will use the estimated throughput extracted directly from the
wifi driver (when available) by querying cfg80211.
Batman-adv will also send some unicast probing packets when
an interface is not used for payload traffic to make sure that
such values are current.
The new protocol can be compiled-in or not like other
features we have and when selected will pull in CFG80211 as
dependency for the reason described above.
Thanks to the big work brought up in the past by Marek Lindner,
batman-adv can easily deal several protocol implementations,
therefore compiling in this new version does not exclude the
older.
This means that the user is offered the option to choose
the protocol when creating the mesh interface (default is the
old one to keep backward compatibility).
Along with the protocol there are some sysfs knobs that are
introduced to fine tune some of its behaviours, but users
are recommended to keep the default values unless they know
what they are doing.
The last patch is about advertising our own patchwork platform
(thanks to Sven Eckelmann for having set that up!) in the
MAINTAINERS file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJW1AvOAAoJENpFlCjNi1MRKxsP/1BR8Wh3MrtNhX7MMe7PnZEQ
p00kArkjtnZCbBVFbG3JduqYaOPnGyzCLgBgF3DnOxx8gAGUEu6fu4AQNNr9jiUM
4lPnPbe5NuvjzQW27fJDZMuy4Y1FLaJ5DeoYjDH48/YDNS38nzlPPtNwg0pJA2TG
C22dM6CX9kzxiy5RETmjgIjK2fgIybudWtCv7BGZxNyiqMaq+bYD+ZJJ6/wbj/FV
uKbWB28puJZ3U3qTJ6ygbhAq8moeubp/nbZeh2RGkhpmnS7LKgdLWyPxJLAEza7Z
jbdhyAE2xDYaU2xxVdOH9GecSYeUlQ+mrBdEblo2cfKMgShwZBrNjQxCaJIHN3G9
ta44yUpjGFl6/HIQnzfNZD4bTRNnb/DeRTG5qWxdrGAbxZESsMPf1Ph/hZ+KvSZ5
7eSZPmVGRYl8hJaLc25bG8pCOLQRsx/54hXNqYRqmImiPQi4IRvKUQkEDXBpHrT+
EwChfIQvCJSzZQAljrhYP/ytg/CiZxNKgW1u8cJRlHRs3jbBxJUJ67gvf2yWdQdj
Luc76uLA1++8QLqhny6AtLeRrr7mYDFnJuNjkwbqWFSyBK6r/lKS1L3ereTfeVIM
5VWMuEDlbWuPscufDJ6WDgWwTqypybjvYbnDlQV7xHap7OegyS/ukQVz2W5lXvS1
gGERfC8WeW1JnFb5TSAY
=qd6p
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
batman-adv 20160229
this is our (hopefully) latest batch of patches intended for net-next.
With this patchset we finally introduce B.A.T.M.A.N. V: the latest
version of our routing protocol.
Technical documentation describing the protocol in more detail can
be found in our wiki[1][2][3][4].
For what concerns this pull request, you can find the high level
description right below.
[1] https://www.open-mesh.org/projects/batman-adv/wiki/BATMAN_V
[2] https://www.open-mesh.org/projects/batman-adv/wiki/OGMv2
[3] https://www.open-mesh.org/projects/batman-adv/wiki/ELP
[4] https://www.open-mesh.org/projects/batman-adv/wiki/BATMAN_V_Tests
...
With this patchset we finally introduce our new routing protocol:
B.A.T.M.A.N. V. Its implementation started quite some years ago,
but due to the big changes being introduced it took a while to be
discussed, designed, worked, re-worked, tested and debugged (well,
we're never done with the latest). The entire operation has
basically been a team work involving all the core contributors
together with other people interested in the project.
The new protocol is divided into two main subcomponents, called
respectively ELP and OGMv2. The former is in charge of
dealing with the neighbour discovery and link quality estimation,
while the latter implements the algorithm that spreads the
metrics around the network and computes optimal paths.
The biggest change introduced with B.A.T.M.A.N. V is the new
metric: the protocol won't rely on packet loss anymore, but it
will use the estimated throughput extracted directly from the
wifi driver (when available) by querying cfg80211.
Batman-adv will also send some unicast probing packets when
an interface is not used for payload traffic to make sure that
such values are current.
The new protocol can be compiled-in or not like other
features we have and when selected will pull in CFG80211 as
dependency for the reason described above.
Thanks to the big work brought up in the past by Marek Lindner,
batman-adv can easily deal several protocol implementations,
therefore compiling in this new version does not exclude the
older.
This means that the user is offered the option to choose
the protocol when creating the mesh interface (default is the
old one to keep backward compatibility).
Along with the protocol there are some sysfs knobs that are
introduced to fine tune some of its behaviours, but users
are recommended to keep the default values unless they know
what they are doing.
The last patch is about advertising our own patchwork platform
(thanks to Sven Eckelmann for having set that up!) in the
MAINTAINERS file.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since offset is zero, it's not necessary to use set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] net/sched/sch_mqprio.o
net/sched/sch_mqprio.c: In function ?mqprio_init?:
net/sched/sch_mqprio.c:145: error: unknown field ?tc? specified in initializer
net/sched/sch_mqprio.c:145: warning: missing braces around initializer
net/sched/sch_mqprio.c:145: warning: (near initialization for ?tc.<anonymous>?)
make[2]: *** [net/sched/sch_mqprio.o] Error 1
make[1]: *** [net/sched] Error 2
make: *** [net] Error 2
Several people reported this, surround the unnamed union
member initialization with braces to fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
of_mdiobus_register() declares the 'paddr' variable to hold the result of
the of_get_property() but only uses it once after that while the function
can be called directly from the *if* statement. Remove that variable and
switch to calling of_find_property() instead since we don't care about
the "reg" property's value anyway...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
qed: Attention support patch series
Until now we've only enabled attention generation for the sake of
management firmware indications [required for link notifications].
This series enables [almost] all the attention sources of the HW,
currently for the sake of logging information relating to issues
experienced by HW. In future, infrastructure laid here would also be used
for the sake of the recovery process.
The first patch in the series is a semantic alignemnt of the code.
The later 3 patches incremently create said infrastructure and enrich
the logged information.
Notice #3 contains quite a bit of structures [consisting of ~1K lines]
that will eventually be removed and incorporated in the binary fw file.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch utilizes the attention infrastructure to log additional
information that relates only to specific HW blocks.
For some of those HW blocks, it also stops automatically disabling the
attention generation as the attention is considered benign and thus
should only be logged; No fear of it flooding the system.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each HW block contains common information about attention reasons,
raising a bit for each one of the different sub-reasons that caused it
to raise an attention.
This patch extends the infrastructure by allowing logging of the various
reasons causing the HW blocks to generate an attention.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW is capable of generating attentnions for a multitude of reasons,
but current driver is enabling attention generation only for management
firmware [required for link notifications].
This patch enables almost all of the possible reasons for HW attentions,
logging the HW block generating the attention and preventing further
attentions from that source [to prevent possible attention flood].
It also lays the infrastructure for additional exploration of the various
attentions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 52bd2d62ce ("net: better skb->sender_cpu and skb->napi_id cohabitation")
skb_sender_cpu_clear() becomes empty and can be removed.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5 driver updates
This series includes some bug fixes and updates for the mlx5 core
and ethernet driver.
From Gal, two fixes that protects the update CQ moderation flows
when it is not allowed.
From Moshe, two fixes for the core and ethernet driver in
non-cached(NC) and write combining(WC) buffers mappings,
which prevents the driver from double memory mappings.
From Or, reduce the firmware command completion timeout.
From Tariq, several small trivial fixes.
Changes from v0:
- "Fix global UAR mapping" commit messages updated to explain ARCH_HAS_IOREMAP_WC usage.
- rebased to commit 8d3f2806f8 'Merge branch ethtool-ksettings'
Changes from v1:
- Removed ARCH_HAS_IOREMAP_WC config flag from "Fix global UAR mapping" commit, as it was not accurate to use it.
- Squashed "Fix global UAR mapping" and "net/mlx5: Avoid double mapping of io mapped memory"
- Added more info for "Fix global UAR mapping" in commit message
Changes from v2:
- None. resubmission per Dave's request due to two parallel submissions to mlx5 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid double mapping of io mapped memory, Device page may be
mapped to non-cached(NC) or to write-combining(WC).
The code before this fix tries to map it both to WC and NC
contrary to what stated in Intel's software developer manual.
Here we remove the global WC mapping of all UARS
"dev->priv.bf_mapping", since UAR mapping should be decided
per UAR (e.g we want different mappings for EQs, CQs vs QPs).
Caller will now have to choose whether to map via
write-combining API or not.
mlx5e SQs will choose write-combining in order to perform
BlueFlame writes.
Fixes: 88a85f99e5 ('TX latency optimization to save DMA reads')
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Reviewed-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The command timeout is terribly long, whole two hours. Make it 60s so if
things do go wrong, the user gets feedback in relatively short time, so
they can take corrective actions and/or investigate using tools and such.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling mlx5e_set_coalesce while the interface is down will result in
modifying CQs that don't exist.
Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CQ moderation is not supported by the device, print a warning on
netdevice load, and return error when trying to modify/query cq
moderation via ethtool.
Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By its role, there is no need to set all the other parameters
for the drop RQ.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For data cache locality considerations, we moved the nop and
csum_offload_inner within sq_stats struct as they are more
commonly accessed in xmit path.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of the pair (channel, tc), we now use a single number that
goes over all tx queues of a TC, for all TCs.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More proper to declare carrier state UP only after the channels
are ready for traffic.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need to flush the irq handler to make sure it does not
queue a work into the global work queue after we start to flush it.
So using synchronize_irq() is more appropriate than a spin lock.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f1705ec197 allows IPv6 addresses to be retained on a link down.
The address can have a cached host route which can point to the wrong
FIB table if the L3 enslavement is changed (e.g., route can point to local
table instead of VRF table if device is added to an L3 domain).
On link up check the table of the cached host route against the FIB
table associated with the device and correct if needed.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deepa Dinamani says:
====================
Convert network timestamps to be y2038 safe
Introduction:
The series is aimed at transitioning network timestamps to being
y2038 safe.
All patches can be reviewed and merged independently.
Socket timestamps and ioctl calls will be handled separately.
Thanks to Arnd Bergmann for discussing solution options with me.
Solution:
Data type struct timespec is not y2038 safe.
Replace timespec with struct timespec64 which is y2038 safe.
Changes v1 -> v2:
Move and rename inet_current_time() as discussed
Squash patches 1 and 2
Reword commit text for patch 2/3
Carry over review tags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP probe log timestamps use struct timespec which is
not y2038 safe.
Use struct timespec64 which is 2038 safe instead.
Use monotonic time instead of real time as only time
differences are logged.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-sctp@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP probe log timestamps use struct timespec which is
not y2038 safe. Even though timespec might be good enough here
as it is used to represent delta time, the plan is to get rid
of all uses of timespec in the kernel.
Replace with struct timespec64 which is y2038 safe.
Prints still use unsigned long format and type.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICMP timestamp messages and IP source route options require
timestamps to be in milliseconds modulo 24 hours from
midnight UT format.
Add inet_current_timestamp() function to support this. The function
returns the required timestamp in network byte order.
Timestamp calculation is also changed to call ktime_get_real_ts64()
which uses struct timespec64. struct timespec64 is y2038 safe.
Previously it called getnstimeofday() which uses struct timespec.
struct timespec is not y2038 safe.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal Hadi Salim says:
====================
net_sched: Add support for IFE action
As agreed at netconf in Seville, here's the patch finally (1 year
was just too long to wait for an ethertype. Now we are just going
have the user configure one).
Described in netdev01 paper:
"Distributing Linux Traffic Control Classifier-Action Subsystem"
Authors: Jamal Hadi Salim and Damascene M. Joachimpillai
The original motivation and deployment of this work was to horizontally
scale packet processing at scope of a chasis or rack. This means one
could take a tc policy and split it across machines connected over
L2. The paper refers to this as "pipeline stage indexing". Other
use cases which evolved out of the original intent include but are
not limited to carrying OAM information, carrying exception handling
metadata, carrying programmed authentication and authorization information,
encapsulating programmed compliance information, service IDs etc.
Read the referenced paper for more details.
The architecture allows for incremental updates for new metadatum support
to cover different use cases.
This patch set includes support for basic skb metadatum.
Followup patches will have more examples of metadata and other features.
v4 changes:
Integrate more feedback from Cong
v3 changes:
Integrate with the new namespace changes
Remove skbhash and queue mapping metadata (but keep their claim for ids)
Integrate feedback from Cong
Integrate feedback from Daniel
v2 changes:
Remove module option for an upper bound of metadata
Integrate feedback from Cong
Integrate feedback from Daniel
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Example usage:
Set the skb priority using skbedit then allow it to be encoded
sudo tc qdisc add dev $ETH root handle 1: prio
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action skbedit prio 17 \
action ife encode \
allow prio \
dst 02:15:15:15:15:15
Note: You dont need the skbedit action if you are already encoding the
skb priority earlier. A zero skb priority will not be sent
Alternative hard code static priority of decimal 33 (unlike skbedit)
then mark of 0x12 every time the filter matches
sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action ife encode \
type 0xDEAD \
use prio 33 \
use mark 0x12 \
dst 02:15:15:15:15:15
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Example usage:
Set the skb using skbedit then allow it to be encoded
sudo tc qdisc add dev $ETH root handle 1: prio
sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action skbedit mark 17 \
action ife encode \
allow mark \
dst 02:15:15:15:15:15
Note: You dont need the skbedit action if you are already encoding the
skb mark earlier. A zero skb mark, when seen, will not be encoded.
Alternative hard code static mark of 0x12 every time the filter matches
sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 \
u32 match ip protocol 1 0xff flowid 1:2 \
action ife encode \
type 0xDEAD \
use mark 0x12 \
dst 02:15:15:15:15:15
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action allows for a sending side to encapsulate arbitrary metadata
which is decapsulated by the receiving end.
The sender runs in encoding mode and the receiver in decode mode.
Both sender and receiver must specify the same ethertype.
At some point we hope to have a registered ethertype and we'll
then provide a default so the user doesnt have to specify it.
For now we enforce the user specify it.
Lets show example usage where we encode icmp from a sender towards
a receiver with an skbmark of 17; both sender and receiver use
ethertype of 0xdead to interop.
YYYY: Lets start with Receiver-side policy config:
xxx: add an ingress qdisc
sudo tc qdisc add dev $ETH ingress
xxx: any packets with ethertype 0xdead will be subjected to ife decoding
xxx: we then restart the classification so we can match on icmp at prio 3
sudo $TC filter add dev $ETH parent ffff: prio 2 protocol 0xdead \
u32 match u32 0 0 flowid 1:1 \
action ife decode reclassify
xxx: on restarting the classification from above if it was an icmp
xxx: packet, then match it here and continue to the next rule at prio 4
xxx: which will match based on skb mark of 17
sudo tc filter add dev $ETH parent ffff: prio 3 protocol ip \
u32 match ip protocol 1 0xff flowid 1:1 \
action continue
xxx: match on skbmark of 0x11 (decimal 17) and accept
sudo tc filter add dev $ETH parent ffff: prio 4 protocol ip \
handle 0x11 fw flowid 1:1 \
action ok
xxx: Lets show the decoding policy
sudo tc -s filter ls dev $ETH parent ffff: protocol 0xdead
xxx:
filter pref 2 u32
filter pref 2 u32 fh 800: ht divisor 1
filter pref 2 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:1 (rule hit 0 success 0)
match 00000000/00000000 at 0 (success 0 )
action order 1: ife decode action reclassify
index 1 ref 1 bind 1 installed 14 sec used 14 sec
type: 0x0
Metadata: allow mark allow hash allow prio allow qmap
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
xxx:
Observe that above lists all metadatum it can decode. Typically these
submodules will already be compiled into a monolithic kernel or
loaded as modules
YYYY: Lets show the sender side now ..
xxx: Add an egress qdisc on the sender netdev
sudo tc qdisc add dev $ETH root handle 1: prio
xxx:
xxx: Match all icmp packets to 192.168.122.237/24, then
xxx: tag the packet with skb mark of decimal 17, then
xxx: Encode it with:
xxx: ethertype 0xdead
xxx: add skb->mark to whitelist of metadatum to send
xxx: rewrite target dst MAC address to 02:15:15:15:15:15
xxx:
sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 u32 \
match ip dst 192.168.122.237/24 \
match ip protocol 1 0xff \
flowid 1:2 \
action skbedit mark 17 \
action ife encode \
type 0xDEAD \
allow mark \
dst 02:15:15:15:15:15
xxx: Lets show the encoding policy
sudo tc -s filter ls dev $ETH parent 1: protocol ip
xxx:
filter pref 10 u32
filter pref 10 u32 fh 800: ht divisor 1
filter pref 10 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:2 (rule hit 0 success 0)
match c0a87aed/ffffffff at 16 (success 0 )
match 00010000/00ff0000 at 8 (success 0 )
action order 1: skbedit mark 17
index 6 ref 1 bind 1
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
action order 2: ife encode action pipe
index 3 ref 1 bind 1
dst MAC: 02:15:15:15:15:15 type: 0xDEAD
Metadata: allow mark
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
xxx:
test by sending ping from sender to destination
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov says:
====================
bridge: mcast: add support for temp router port
This set adds support for temporary router port which doesn't depend only
on the incoming queries. It can be refreshed by setting multicast_router to
the same value (3). The first two patches are minor changes that prepare
the code for the third which adds this new type of router port.
In order to be able to dump its information the mdb router port format
is changed in patch 04 and extended similar to how mdb entries format was
done recently.
The related iproute2 changes will be posted if this is accepted.
v2: set val first and adjust router type later in patch 01, patch 03 was
split in 2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow for more multicast router port information to be dumped such as
timer and type attributes. For that that purpose we need to extend the
MDBA_ROUTER_PORT attribute similar to how it was done for the mdb entries
recently. The new format is thus:
[MDBA_ROUTER_PORT] = { <- nested attribute
u32 ifindex <- router port ifindex for user-space compatibility
[MDBA_ROUTER_PATTR attributes]
}
This way it remains compatible with older users (they'll simply retrieve
the u32 in the beginning) and new users can parse the remaining
attributes. It would also allow to add future extensions to the router
port without breaking compatibility.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a temporary router port which doesn't depend only on the
incoming query. It can be refreshed if set to the same value, which is
a no-op for the rest.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed for the upcoming temporary port router. There's no point
to go through the logic if the value is the same.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using raw values makes it difficult to extend and also understand the
code, give them names and do explicit per-option manipulation in
br_multicast_set_port_router.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: implement VLAN filtering
This patchset fixes hardware bridging for non 802.1Q aware systems.
The mv88e6xxx DSA driver currently depends on CONFIG_VLAN_8021Q and
CONFIG_BRIDGE_VLAN_FILTERING enabled for correct bridging between switch ports.
Patch 1/9 adds support for the VLAN filtering switchdev attribute in DSA.
Patchs 2/9 and 3/9 add helper functions for the following patches.
Patchs 4/9 to 6/9 assign dynamic address databases to VLANs, ports, and
bridge groups (the lowest available FID is cleared and assigned), and thus
restore support for per-port FDB operations.
Patchs 7/9 to 9/9 refine ports isolation and setup 802.1Q on user demand.
With this patchset, ports get correctly bridged and the driver behaves as
expected, with or without 802.1Q support.
With CONFIG_VLAN_8021Q enabled, setting a default PVID to the bridge correctly
propagates the corresponding VLAN, in addition to the hardware bridging:
# echo 42 > /sys/class/net/<bridge>/bridge/default_pvid
But considering CONFIG_BRIDGE_VLAN_FILTERING enabled, the hardware VLAN
filtering is enabled on all bridge members only when the user requests it:
# echo 1 > /sys/class/net/<bridge>/bridge/vlan_filtering
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement port_vlan_filtering in the driver to toggle the related port
802.1Q mode between DISABLED and SECURE, on user request.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ports isolation is correctly configured when joining or leaving
a bridge, there is no need to rely on reserved VLANs to isolate
unbridged ports anymore. Thus remove them, and disable 802.1Q on setup.
This restores the expected behavior of hardware bridging for systems
without 802.1Q or VLAN filtering enabled.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The In Chip Port Based VLAN Table contains bits used to restrict which
output ports this input port can send frames to.
With the VLAN filtering enabled, these tables work in conjunction with
the VLAN Table Unit to allow egressing frames.
In order to remove the current dependency to BRIDGE_VLAN_FILTERING for
basic hardware bridging to work, it is necessary to restore a fine
control of each port's VLANTable, on setup and when a port joins or
leaves a bridge.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Give a new bridge a fresh FDB, assign it to its members, and restore a
fresh FDB to a port leaving a bridge.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restore per-port FDB. Assign them on setup, allow adding and deleting
addresses into them, and dump them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
