When taking the core idle state lock, grab it immediately like a regular
lock, rather than adding more tests in there. Holding the lock keeps it
stable, so there is no need to do it whole holding the reservation.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In preparation for adding more bits to the core idle state word, move
the lock bit up, and unlock by flipping the lock bit rather than masking
off all but the thread bits.
Add branch hints for atomic operations while we're here.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ISA specifies power save wakeup due to a machine check exception can
cause a machine check interrupt (rather than the usual system reset
interrupt).
The machine check handler copes with this by doing low level machine
check recovery without restoring full state from idle, then queues up a
machine check event for logging, then directly executes the same idle
instruction it woke from. This minimises the work done before recovery
is performed.
The problem is that it requires machine specific instructions and
knowledge of the book3s idle code. Currently it only has code to handle
POWER8 idle, so POWER9 crashes when trying to execute the P8 idle
instructions which don't exist in ISAv3.0B.
cpu 0x0: Vector: e40 (Emulation Assist) at [c0000000008f3810]
pc: c000000000008380: machine_check_handle_early+0x130/0x2f0
lr: c00000000053a098: stop_loop+0x68/0xd0
sp: c0000000008f3a90
msr: 9000000000081001
current = 0xc0000000008a1080
paca = 0xc00000000ffd0000 softe: 0 irq_happened: 0x01
pid = 0, comm = swapper/0
Instead of going to sleep after recovery, do the usual idle wakeup and
state restoration by calling into the normal idle wakeup path. This
reuses the normal idle wakeup paths.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Mahesh J Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reduces the number of nops for POWER8.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The POWER8 idle code has a neat trick of programming the power on engine
to restore a low bit into HSPRG0, so idle wakeup code can test and see
if it has been programmed this way and therefore lost all state. Restore
time can be reduced if winkle has not been reached.
However this messes with our r13 PACA pointer, and requires HSPRG0 to be
written to. It also optimizes the slowest and most uncommon case at the
expense of another SPR write in the common nap state wakeup.
Remove this complexity and assume winkle sleeps always require a state
restore. This speedup could be made entirely contained within the winkle
idle code by counting per-core winkles and setting a thread bitmap when
all have gone to winkle.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No functional change.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The system reset idle handler system_reset_idle_common is relocated, so
relocation is not required to branch to kvm_start_guest. The superfluous
relocation does not result in incorrect code, but it does not compile
outside of exception-64s.S (with fixed section definitions).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add powerpc support for mmap_rnd_bits and mmap_rnd_compat_bits, which are two
sysctls that allow a user to configure the number of bits of randomness used for
ASLR.
Because of the way the Kconfig for ARCH_MMAP_RND_BITS is defined, we have to
construct at least the MIN value in Kconfig, vs in a header which would be more
natural. Given that we just go ahead and do it all in Kconfig.
At least according to the code (the documentation makes no mention of it), the
value is defined as the number of bits of randomisation *of the page*, not the
address. This makes some sense, with larger page sizes more of the low bits are
forced to zero, which would reduce the randomisation if we didn't take the
PAGE_SIZE into account. However it does mean the min/max values have to change
depending on the PAGE_SIZE in order to actually limit the amount of address
space consumed by the randomisation.
The result of that is that we have to define the default values based on both
32-bit vs 64-bit, but also the configured PAGE_SIZE. Furthermore now that we
have 128TB address space support on Book3S, we also have to take that into
account.
Finally we can wire up the value in arch_mmap_rnd().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
The default implementation of ioremap_cache() is aliased to ioremap().
On powerpc ioremap() creates cache-inhibited mappings by default which
is almost certainly not what you wanted.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Hypervisor Virtualization and Directed Hypervisor Doorbell interrupt handlers
use the macro EXC_VIRT_OOL_MASKABLE_HV for their relocation-on handlers, which
calls MASKABLE_RELON_EXCEPTION_HV_OOL, which uses the *real mode* interrupt
prolog. This means we needlessly rfid from virtual mode to virtual mode.
For POWER8 it only affects doorbell IPIs. Context switch microbenchmark between
threads with snooze disabled (which causes IPI) gets about 3% faster, about 370
cycles. Should be more important on POWER9 with global doorbells and HVI for
host interrupts.
Use the RELON variant instead to reduce overhead.
Fixes: 1707dd1613 ("powerpc: Save CFAR before branching in interrupt entry paths")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fold some more detail into the change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Dan Carpenter noticed that the code in __xive_native_disable_queue() has a for
loop with an unconditional break in the middle, which doesn't make a lot of
sense.
What the code's supposed to do is loop as long as OPAL says it's busy, if we get
any other return code, either success or failure, then we should break the loop.
So add the missing check.
Fixes: 243e25112d ("powerpc/xive: Native exploitation of the XIVE interrupt controller")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Power9 DD1 does not implement SAO. Although it's not widely used, its presence
or absence is visible to user space via arch_validate_prot() so it's moderately
important that we get the value right.
Fixes: 7dccfbc325 ("powerpc/book3s: Add a cpu table entry for different POWER9 revs")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Power9 does not implement the icswx instruction. This CPU feature is not visible
to userspace and is only used in the CONFIG_PPC_ICSWX code, which is generally
not enabled, and can only be triggered by other code using icswx, which should
not happen on Power9 systems in the first place. So impact should be minimal.
Fixes: c3ab300ea5 ("powerpc: Add POWER9 cputable entry")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Patch add "mem_access" event to sysfs. This as-is not a raw event
supported by Power8 pmu. Instead, it is formed based on
raw event encoding specificed in isa207-common.h.
Primary PMU event used here is PM_MRK_INST_CMPL.
This event tracks only the completed marked instructions.
Random sampling mode (MMCRA[SM]) with Random Instruction
Sampling (RIS) is enabled to mark type of instructions.
With Random sampling in RLS mode with PM_MRK_INST_CMPL event,
the LDST /DATA_SRC fields in SIER identifies the memory
hierarchy level (eg: L1, L2 etc) statisfied a data-cache
miss for a marked instruction.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Patch to export SIER bits to userspace via
perf_mem_data_src and perf_sample_data struct.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Patch to export SIER bits to userspace via
perf_mem_data_src and perf_sample_data struct.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Threshold feature when used with MMCRA [Threshold Event Counter Event],
MMCRA[Threshold Start event] and MMCRA[Threshold End event] will update
MMCRA[Threashold Event Counter Exponent] and MMCRA[Threshold Event
Counter Multiplier] with the corresponding threshold event count values.
Patch to export MMCRA[TECX/TECM] to userspace in 'weight' field of
struct perf_sample_data.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The LDST field and DATA_SRC in SIER identifies the memory hierarchy level
(eg: L1, L2 etc), from which a data-cache miss for a marked instruction
was satisfied. Use the 'perf_mem_data_src' object to export this
hierarchy level to user space.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
perf_mem_data_src is a union that is initialized in the kernel via the ->val
field and accessed by userspace via the mem_xxx bitfields. For this to work
correctly on big endian platforms, we need a big-endian definition for the
bitfields.
Currently on a big endian system, if a user requests PERF_SAMPLE_DATA_SRC (perf
report -d), they will get the default value from perf_sample_data_init(), which
is PERF_MEM_NA. The value for PERF_MEM_NA is constructed using shifts:
/* TLB access */
#define PERF_MEM_TLB_NA 0x01 /* not available */
...
#define PERF_MEM_TLB_SHIFT 26
#define PERF_MEM_S(a, s) \
(((__u64)PERF_MEM_##a##_##s) << PERF_MEM_##a##_SHIFT)
#define PERF_MEM_NA (PERF_MEM_S(OP, NA) |\
PERF_MEM_S(LVL, NA) |\
PERF_MEM_S(SNOOP, NA) |\
PERF_MEM_S(LOCK, NA) |\
PERF_MEM_S(TLB, NA))
Which works out as:
((0x01 << 0) | (0x01 << 5) | (0x01 << 19) | (0x01 << 24) | (0x01 << 26))
Which means the PERF_MEM_NA value comes out of the kernel as 0x5080021
in CPU endian.
But then in the perf tool, the code uses the bitfields to inspect the value, and
currently the bitfields are defined using little endian ordering.
So eg. in perf_mem__tlb_scnprintf() we see:
data_src->val = 0x5080021
op = 0x0
lvl = 0x0
snoop = 0x0
lock = 0x0
dtlb = 0x0
rsvd = 0x5080021
Because of the way the perf tool code is written this is still displayed to the
user as "N/A", so there is no bug visible at the UI level.
Currently there are no big endian architectures which export a meaningful
value (ie. other than PERF_MEM_NA), so the extent of the bug on big endian
platforms is that the PERF_MEM_NA value is exported incorrectly as described
above. Subsequent patches will add support on big endian powerpc for populating
the data source value.
This patch does a minimal fix of adding big endian definition of the bitfields
to match the values that are already exported by the kernel on big endian. And
it makes no change on little endian.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The CMA pages migration code does not support compound pages at
the moment so it performs few tests before proceeding to actual page
migration.
One of the tests - PageTransHuge() - has VM_BUG_ON_PAGE(PageTail()) as
it is designed to be called on head pages only. Since we also test for
PageCompound(), and it contains PageTail() and PageHead(), we can
simplify the check by leaving just PageCompound() and therefore avoid
possible VM_BUG_ON_PAGE.
Fixes: 2e5bbb5461 ("KVM: PPC: Book3S HV: Migrate pinned pages out of CMA")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As part of the new large address space support, processes start out life with a
128TB virtual address space. However when calling mmap() a process can pass a
hint address, and if that hint is > 128TB the kernel will use the full 512TB
address space to try and satisfy the mmap() request.
Currently we have a check that the hint is > 128TB and < 512TB (TASK_SIZE),
which was added as an optimisation to avoid updating addr_limit unnecessarily
and also to avoid calling slice_flush_segments() on all CPUs more than
necessary.
However this has the user-visible side effect that an mmap() hint above 512TB
does not search the full address space unless a preceding mmap() used a hint
value > 128TB && < 512TB.
So fix it to treat any hint above 128TB as a hint to search the full address
space, instead of checking the hint against TASK_SIZE, we instead check if the
addr_limit is already == TASK_SIZE.
This also brings the ABI in-line with what is proposed on x86. ie, that a hint
address above 128TB up to and including (2^64)-1 is an indication to search the
full address space.
Fixes: f4ea6dcb08 (powerpc/mm: Enable mappings above 128TB)
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add support for future IBM Coherent Accelerator (CXL) devices
with an IDs of 0x0623 and 0x0628.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The TLB flush for radix first flushes TLB for radix configuration,
then flushes for hash configuration. The second flush is unnecessary
but does not affect correctness.
Fixes: 1a472c9dba ("powerpc/mm/radix: Add tlbflush routines")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We don't init addr_limit correctly for 32 bit applications. So default to using
mm->task_size for boundary condition checking. We use addr_limit to only control
free space search. This makes sure that we do the right thing with 32 bit
applications.
We should consolidate the usage of TASK_SIZE/mm->task_size and
mm->context.addr_limit later.
This partially reverts commit fbfef9027c (powerpc/mm: Switch some
TASK_SIZE checks to use mm_context addr_limit).
Fixes: fbfef9027c ("powerpc/mm: Switch some TASK_SIZE checks to use mm_context addr_limit")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The XIVE enablement patches included a change to set the LPES (Logical
Partitioning Environment Selector) bit (bit # 3) in LPCR (Logical Partitioning
Control Register) on POWER9 hosts. This bit sets external interrupts to guest
delivery mode, which uses SRR0/1. The host's EE interrupt handler is written to
expect HSRR0/1 (for earlier CPUs). This should be fine because XIVE is
configured not to deliver EEs to the host (Hypervisor Virtulization Interrupt is
used instead) so the EE handler should never be executed.
However a bug in interrupt controller code, hardware, or odd configuration of a
simulator could result in the host getting an EE incorrectly. Keeping the EE
delivery mode matching the host EE handler prevents strange crashes due to using
the wrong exception registers.
KVM will configure the LPCR to set LPES prior to running a guest so that EEs are
delivered to the guest using SRR0/1.
Fixes: 08a1e650cc ("powerpc: Fixup LPCR:PECE and HEIC setting on POWER9")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Massage change log to avoid referring to LPES0 which is now renamed LPES]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pseries platform supports Power4 and later CPUs, all of which are
multithreaded and/or multicore.
In practice no one ever builds a SMP=n kernel for these machines. So as
we did for powernv, have the pseries platform imply SMP=y.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The powernv platform supports Power7 and later CPUs, all of which are
multithreaded and multicore.
As such we never build a SMP=n kernel for those machines, other than
possibly for debugging or running in a simulator.
In the debugging case we can get a similar effect by booting with
nr_cpus=1, or there's always the option of building a custom kernel with
SMP hacked out.
For running in simulators the code size reduction from building without
SMP is not particularly important, what matters is the number of
instructions executed. A quick test shows that a SMP=y kernel takes ~6%
more instructions to boot to a shell. Booting with nr_cpus=1 recovers
about half that deficit.
On the flip side, keeping the SMP=n kernel building can be a pain at
times. And although we've mostly kept it building in recent years, no
one is regularly testing that the SMP=n kernel actually boots and works
well on these machines.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Of the 64-bit Book3S platforms, only powermac supports booting on an
actual non-SMP system. The other platforms can be built with SMP
disabled, but it doesn't make a lot of sense given the CPUs they support
are all multicore or multithreaded.
So give platforms the option of forcing SMP=y.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently powerpc's asm/io.h includes linux/io.h, and linux/io.h
includes asm/io.h.
This can cause problems because depending on which is included first the
order of definitions between the two files will change.
The include of linux/io.h was added back in 2008 in commit b41e5fffe8
("[POWERPC] devres: Add devm_ioremap_prot()"). It's not entirely clear
it was needed then, but devm_ioremap_prot() has since been removed
entirely as unused, in dedd24a12f ("powerpc: Remove unused
devm_ioremap_prot()").
So it seems to be unnecessary and can potentially cause problems, so
remove the include of linux/io.h from asm/io.h
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 requires msgsync for receiver-side synchronization, and a DD1
workaround restricts IPIs to core-local.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Drop no longer needed asm feature macro changes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
IPIs are a pretty hot path and we already have the ability to do asm feature
patching, so use it.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Change log detail]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 changes requirements and adds new instructions for
synchronization.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change the doorbell callers to know about their msgsnd addressing,
rather than have them set a per-cpu target data tag at boot that gets
sent to the cause_ipi functions. The data is only used for doorbell IPI
functions, no other IPI types, so it makes sense to keep that detail
local to doorbell.
Have the platform code understand doorbell IPIs, rather than the
interrupt controller code understand them. Platform code can look at
capabilities it has available and decide which to use.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add the bit definition and use it in facility_unavailable_exception() so we can
intelligently report the cause if we take a fault for SCV. This doesn't actually
enable SCV.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Drop whitespace changes to the existing entries, flush out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have a #define for it, so use it.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The new Coherent Accelerator Interface Architecture, level 2, for the
IBM POWER9 brings new content and features:
- POWER9 Service Layer
- Registers
- Radix mode
- Process element entry
- Dedicated-Shared Process Programming Model
- Translation Fault Handling
- CAPP
- Memory Context ID
If a valid mm_struct is found the memory context id is used for each
transaction associated with the process handle. The PSL uses the
context ID to find the corresponding process element.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
[mpe: Fixup comment formatting, unsplit long strings]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Point out the specific Coherent Accelerator Interface Architecture,
level 1, registers.
Code and functions specific to PSL8 (CAIA1) must be framed.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
[mpe: Don't split long strings, it makes them hard to grep for]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rename a few functions, changing the '_psl' suffix to '_psl8', to make
clear that the implementation is psl8 specific.
Those functions will have an equivalent implementation for the psl9 in
a later patch.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The service layer API (in cxl.h) lists some low-level functions whose
implementation is different on PSL8, PSL9 and XSL:
- Init implementation for the adapter and the afu.
- Invalidate TLB/SLB.
- Attach process for dedicated/directed models.
- Handle psl interrupts.
- Debug registers for the adapter and the afu.
- Traces.
Each environment implements its own functions, and the common code uses
them through function pointers, defined in cxl_service_layer_ops.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The mm_struct corresponding to the current task is acquired each time
an interrupt is raised. So to simplify the code, we only get the
mm_struct when attaching an AFU context to the process.
The mm_count reference is increased to ensure that the mm_struct can't
be freed. The mm_struct will be released when the context is detached.
A reference on mm_users is not kept to avoid a circular dependency if
the process mmaps its cxl mmio and forget to unmap before exiting.
The field glpid (pid of the group leader associated with the pid), of
the structure cxl_context, is removed because it's no longer useful.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The two previously fields pid and tid, located in the structure
cxl_irq_info, are only used in the guest environment. To avoid confusion,
it's not necessary to fill the fields in the bare-metal environment.
Pid_tid is now renamed to 'reserved' to avoid undefined behavior on
bare-metal. The PSL Process and Thread Identification Register
(CXL_PSL_PID_TID_An) is only used when attaching a dedicated process
for PSL8 only. This register goes away in CAIA2.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This bit is used to cause a flash image load for programmable
CAIA-compliant implementation. If this bit is set to ‘0’, a power
cycle of the adapter is required to load a programmable CAIA-com-
pliant implementation from flash.
This field will be used by the following patches.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current behaviour of the hash table dump assumes that memory is contiguous
and iterates from the start of memory to (start + size of memory). When memory
isn't physically contiguous, this doesn't work.
If memory exists at 0-5 GB and 6-10 GB then the current approach will check if
entries exist in the hash table from 0GB to 9GB. This patch changes the
behaviour to iterate over any holes up to the end of memory.
Fixes: 1515ab9321 ("powerpc/mm: Dump hash table")
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current page table dumper scans the Linux page tables and coalesces mappings
with adjacent virtual addresses and similar PTE flags. This behaviour is
somewhat broken when you consider the IOREMAP space where entirely unrelated
mappings will appear to be virtually contiguous. This patch modifies the range
coalescing so that only ranges that are both physically and virtually contiguous
are combined. This patch also adds to the dump output the physical address at
the start of each range.
Fixes: 8eb07b1870 ("powerpc/mm: Dump linux pagetables")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[mpe: Print the physicall address with 0x like the other addresses]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On Book3s we have two PTE flags used to mark cache-inhibited mappings:
_PAGE_TOLERANT and _PAGE_NON_IDEMPOTENT. Currently the kernel page table dumper
only looks at the generic _PAGE_NO_CACHE which is defined to be _PAGE_TOLERANT.
This patch modifies the dumper so both flags are shown in the dump.
Fixes: 8eb07b1870 ("powerpc/mm: Dump linux pagetables")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently sys_mmap() and sys_mmap2() (32-bit only), are not visible to the
syscall tracing machinery. This means users are not able to see the execution of
mmap() syscalls using the syscall tracer.
Fix that by using SYSCALL_DEFINE6 for sys_mmap() and sys_mmap2() so that the
meta-data associated with these syscalls is visible to the syscall tracer.
A side-effect of this change is that the return type has changed from unsigned
long to long. However this should have no effect, the only code in the kernel
which uses the result of these syscalls is in the syscall return path, which is
written in asm and treats the result as unsigned regardless.
Example output:
cat-3399 [001] .... 196.542410: sys_mmap(addr: 7fff922a0000, len: 20000, prot: 3, flags: 812, fd: 3, offset: 1b0000)
cat-3399 [001] .... 196.542443: sys_mmap -> 0x7fff922a0000
cat-3399 [001] .... 196.542668: sys_munmap(addr: 7fff922c0000, len: 6d2c)
cat-3399 [001] .... 196.542677: sys_munmap -> 0x0
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Massage change log, add detail on return type change]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Recently in commit f6eedbba7a ("powerpc/mm/hash: Increase VA range to 128TB"),
we increased H_PGD_INDEX_SIZE to 15 when we're building with 64K pages. This
makes it larger than RADIX_PGD_INDEX_SIZE (13), which means the logic to
calculate MAX_PGD_INDEX_SIZE in book3s/64/pgtable.h is wrong.
The end result is that the PGD (Page Global Directory, ie top level page table)
of the kernel (aka. swapper_pg_dir), is too small.
This generally doesn't lead to a crash, as we don't use the full range in normal
operation. However if we try to dump the kernel pagetables we can trigger a
crash because we walk off the end of the pgd into other memory and eventually
try to dereference something bogus:
$ cat /sys/kernel/debug/kernel_pagetables
Unable to handle kernel paging request for data at address 0xe8fece0000000000
Faulting instruction address: 0xc000000000072314
cpu 0xc: Vector: 380 (Data SLB Access) at [c0000000daa13890]
pc: c000000000072314: ptdump_show+0x164/0x430
lr: c000000000072550: ptdump_show+0x3a0/0x430
dar: e802cf0000000000
seq_read+0xf8/0x560
full_proxy_read+0x84/0xc0
__vfs_read+0x6c/0x1d0
vfs_read+0xbc/0x1b0
SyS_read+0x6c/0x110
system_call+0x38/0xfc
The root cause is that MAX_PGD_INDEX_SIZE isn't actually computed to be
the max of H_PGD_INDEX_SIZE or RADIX_PGD_INDEX_SIZE. To fix that move
the calculation into asm-offsets.c where we can do it easily using
max().
Fixes: f6eedbba7a ("powerpc/mm/hash: Increase VA range to 128TB")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This merges the arch part of the XIVE support, leaving the final commit
with the KVM specific pieces dangling on the branch for Paul to merge
via the kvm-ppc tree.
POWER9 DD1.0 hardware has a bug where the SPRs of a thread waking up
from stop 0,1,2 with ESL=1 can endup being misplaced in the core. Thus
the HSPRG0 of a thread waking up from can contain the paca pointer of
its sibling.
This patch implements a context recovery framework within threads of a
core, by provisioning space in paca_struct for saving every sibling
threads's paca pointers. Basically, we should be able to arrive at the
right paca pointer from any of the thread's existing paca pointer.
At bootup, during powernv idle-init, we save the paca address of every
CPU in each one its siblings paca_struct in the slot corresponding to
this CPU's index in the core.
On wakeup from a stop, the thread will determine its index in the core
from the TIR register and recover its PACA pointer by indexing into
the correct slot in the provisioned space in the current PACA.
Furthermore, ensure that the NVGPRs are restored from the stack on the
way out by setting the NAPSTATELOST in paca.
[Changelog written with inputs from svaidy@linux.vnet.ibm.com]
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Call it a bug]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin