should fix the following issue
[ 3229.815012] [ BUG: lock held when returning to user space! ]
[ 3229.815016] 3.5.0-rc7-wl #28 Tainted: G W O
[ 3229.815017]
------------------------------------------------
[ 3229.815019] wpa_supplicant/5783 is leaving the kernel with locks still held!
[ 3229.815022] 1 lock held by wpa_supplicant/5783:
[ 3229.815023] #0: (reg_mutex){+.+.+.}, at: [<fa65834d>]
reg_last_request_cell_base+0x1d/0x60 [cfg80211]
Cc: Luis Rodriguez <mcgrof@gmail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
on disassoc, ieee80211_set_disassoc() goes out of PS
before indicating BSS_CHANGED_ASSOC (not sure why this
is needed, but some drivers might count on the current
behavior).
However, it does it after sending the disassoc
frame, which results in null-data frame being sent
(in order to go out of ps) after we were already sent
the disassoc, which is invalid.
Fix it by going out of ps before sending the disassoc.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
regulatory_update() just calls wiphy_update_regulatory().
wiphy_update_regulatory() assumes you already have
the reg_mutex held so just move the call within locking
context and kill the superfluous regulatory_update().
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that we have wiphy_regulatory_register() we can
tuck away the core's regulatory_update() call there
and make it static.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it clearer what we're doing. This now makes a bit
more sense given that regardless of the wiphy if the cell
base station hint feature is supported we will be modifying the
way the regulatory core behaves.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cellular base stations can provide hints to cfg80211 about
where they think we are. This can be done for example on
a cell phone. To enable these hints we simply allow them
through as user regulatory hints but we allow userspace
to clasify the hint as either coming directly from the
user or coming from a cellular base station. This option
is only available when you enable
CONFIG_CFG80211_CERTIFICATION_ONUS.
The base station hints themselves will not be processed
by the core unless at least one device on the system
supports this feature.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds CONFIG_CFG80211_CERTIFICATION_ONUS which is to
be used for features / code which require a bit of work on
the system integrator's part to ensure that the system will
still pass 802.11 regulatory certification. This option is
also usable for researchers and experimenters looking to add
code in the kernel without impacting compliant code.
We'd use CONFIG_EXPERT alone but it seems that most standard
Linux distributions are enabling CONFIG_EXPERT already. This
allows us to define 802.11 specific kernel features under a
flag that is intended by design to be disabled by standard
Linux distributions, and only enabled by system integrators
or distributions that have done work to ensure regulatory
certification on the system with the enabled features.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While adding regulatory support to ath6kl I noticed that I easily
got the regulatory code confused. The way to reproduce the bug was:
1. iw reg set FI (in userspace)
2. cfg80211 calls ath6kl_reg_notify(FI)
3. ath6kl sets regdomain in firmware
4. firmware sends regdomain event to notify about the new regdomain (FI)
5. ath6kl calls regulatory_hint(FI)
And this (from FI to FI transition) confuses cfg80211 and after that I
only get "Pending regulatory request, waiting for it to be
processed...." messages and regdomain changes won't work anymore.
The reason why ath6kl calls regulatory_hint() is that firmware can change
the regulatory domain by it's own, for example due to 11d IEs. I could
of course workaround this in ath6kl but I think it's better to handle
the case in cfg80211.
The fix is pretty simple, use a different error code if the regdomain is
same and then just set the request processed so that it doesn't block new
requests.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Let the user configure serveral TX error conection quality monitoring
parameters: % error rate, survey interval, and # of attempted packets.
On exceeding the TX failure rate over the given interval, the driver
will send a CQM notify event with the actual TX failure rate and
packets attempted.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In one of my previous patches I erroneously
used nla_put_u32 for the wdev_id, fix that
to use nla_put_u64.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
info->control.sta and control.vif may only be dereferenced
during the drv_tx call otherwise could lead to use-after-free
bugs.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit "mac80211: unify SW/offload remain-on-channel"
moved the cookie assignment from ieee80211_mgmt_tx()
to ieee80211_start_roc_work(). But the latter is only
called where offchannel is needed. If offchannel isn't
needed/used, a uninitialized cookie value would be returned
to userspace.
This patch sets the cookie value when offchannel isn't used.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Revert commit b78e8ceac2
("cfg80211: track monitor channel") and remove the
set_monitor_enabled() callback.
Due to the tracking happening in NETDEV_PRE_UP, it had
introduced bugs because the monitor interface callback
would be called before the device was started. It looks
like there's no way to fix this, and using NETDEV_PRE_UP
is broken anyway (since there's no NETDEV_UP_FAIL), so
remove all that code, track interfaces in NETDEV_UP and
also stop tracking the monitor channel in cfg80211.
This mostly reverts to before the tracking, except that
we keep the interface count tracking so that setting the
monitor channel can be rejected properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This essentially reverts commit 2e165b8184 but
introduces the get_channel operation with a new
wireless_dev argument so that you can retrieve
the channel per interface. This is necessary as
even though we can track all interface channels
(except monitor) we can't track the channel type
used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 870d37fc22.
This code doesn't work as cfg80211 will call
set_monitor_enabled at the wrong time and it
doesn't seem to be possible to fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
roc is destroyed then roc->started is referenced. Keep a local cache.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It may be desirable to use WoWLAN without triggers to
keep the connection alive to the AP while suspended.
Allow this use by enabling WoWLAN without triggers if
no triggers were requested.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Without this change, running AP + station on the same wiphy
does not work since the commit "cfg80211: add channel checking
for iface combinations". The stopped AP prevents the client
from connecting to an AP on a different channel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[line-break commit message to < 72 chars]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the virtual monitor interface is requested
by the driver, it should also be iterated over
when the driver wants to iterate all active
interfaces.
To allow that protect it with the iflist_mtx.
Change-Id: I58ac5de2f4ce93d12c5a98ecd2859f60158d5d69
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To call cfg80211_get_chan_state() we need to lock
the wdev, so we need to lock the wdev_iter mutex
in cfg80211_can_use_iftype_chan(). This needs to
use nested locking for lockdep.
Also, cfg80211_get_chan_state() doesn't actually
use the rdev, so remove that completely including
the lock assertion that isn't needed.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sample_idx is set to a value other than -1 it activates
the IEEE80211_TX_CTL_RATE_CTRL_PROBE flag which disables
frame aggregation. To allow frame aggregation during fixed
rate it is necessary to set max_tp_rate, max_tp_rate2 and
max_prob_rate instead of sample_idx.
Signed-off-by: Sylvain Roger Rieunier <sylvain.roger.rieunier@gmail.com>
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When drop_unencrypted is enabled and MFP is disabled,
non-robust management frames for not-yet associated STA are dropped.
This isn't visible as many management frames sent from the kernel
have TX_INTFL_DONT_ENCRYPT set and management frames injected
from a monitor vif have TX_CTL_INJECTED so aren't dropped.
But management frames sent from userspace via NL80211_CMD_FRAME
do not have this flag set, so are dropped.
This patch make it always accept non-robust management frames.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "no key" case in key selection that decides
whether to drop the frame or not is impossible
to understand, restructure the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[cavallar@lri.fr: removed blank line and restructured action frame clause]
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Some drivers (iwlegacy, iwlwifi and rt2x00) today use the
bss_conf.last_tsf value. By itself though that value is
completely worthless since it may be ancient. What really
is needed is synchronisation between some device time and
the TSF.
To clarify this, rename bss_conf.last_tsf to sync_tsf and
add sync_device_ts which is obtained from rx_status which
gets a new field device_timestamp for this purpose. This
is intentionally not using the mactime field since that
is used for other things and in IBSS is expected to sync
with the IBSS's TSF which isn't necessarily true for the
device timestamp.
Also, since we have the information and it's useful even
before the connection has been established, give all the
timing details to the driver before authenticating.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We waste a lot of space in this struct because it uses
int values where smaller ones would be sufficient. The
upcoming A-MPDU information needs some space, optimize
the struct now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Scan receive is rather inefficient when there are
multiple virtual interfaces. We iterate all of the
virtual interfaces and then notify cfg80211 about
each beacon many times.
Redesign scan RX to happen before everything else.
Then we can also get rid of IEEE80211_RX_IN_SCAN
since we don't have to accept frames into the RX
handlers for scanning or scheduled scanning any
more. Overall, this simplifies the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of tracking whether or not we're in a
scheduled scan, track the virtual interface
(sdata) in an RCU-protected pointer to make it
usable from RX to check the MAC address.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Making the scan_sdata pointer usable with RCU makes
it possible to dereference it in the RX path to see
if a received frame actually matches the interface
that is scanning. This is just preparations, making
the pointer __rcu.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function building probe-request IEs does not validate the band is
supported before dereferencing it. This can result in a panic when
all bands are traversed, as done during sched-scan start.
Warn when this happens and return an empty probe request. Also fix
sched-scan to not waste memory on unsupported bands.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After a new virtual interface is created, reply
to userspace with a message detailing it so it
knows the new wdev identifier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The management frame and remain-on-channel APIs will be
needed in the P2P device abstraction, so move them over
to the new wdev-based APIs. Userspace can still use both
the interface index and wdev identifier for them so it's
backward compatible, but for the P2P Device wdev it will
be able to use the wdev identifier only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few places that iterate the wdev
list and assume wdev->netdev exists, check
there. The rfkill one has to be extended for
each non-netdev type later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since soon there will be virtual interfaces that
don't have a netdev, use the wdev identifier for
the API to retrieve interface data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some nl80211 callbacks will soon need the wdev instead
of the netdev, so add NL80211_FLAG_NEED_WDEV to allow
them to request that. Add NL80211_FLAG_NEED_WDEV_UP as
well which checks the netdev is UP if one exists.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support a P2P device abstraction and
Bluetooth high-speed AMPs, we need to have a way
to identify virtual interfaces that don't have a
netdev associated.
Do this by adding a NL80211_ATTR_WDEV attribute
to identify a wdev which may or may not also be
a netdev.
To simplify things, use a 64-bit value with the
high 32 bits being the wiphy index for this new
wdev identifier in the nl80211 API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This API call was intended to be used by drivers
if they want to optimize key handling by removing
one key when another is added. Remove it since no
driver is using it. If needed, it can always be
added back.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_mlme_notify_scan_completed() iterates all
interfaces and doesn't need to assign anything to
the sdata variable before the loop.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the AC parameters change, drivers might rely
on getting a bss_info_changed notification with
BSS_CHANGED_QOS in addition to the conf_tx call.
Always call the function when userspace updates
are made (in AP/GO modes) and also set the change
flag when updates were made by the AP (in managed
mode.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Quick fix for method being invoked without checking its existence.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Because ieee80211_tx_status in status.c checks if
outgoing BlockAck requests have been acked, it is
necessary to tell the driver that tx feedback for
this sort of frame is important.
Otherwise, the stack will continue to send the same
BlockAck request over and over, which can cause
the receiver to flush or clean its reorder buffer
over and over.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was useful for debugging the queue stop/wake
issues and is pretty small so let's just put it in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Larry (and some others I think) reported that with
single-queue drivers mac80211 crashes when waking
the queues. This happens because we allocate just
a single queue for each virtual interface in case
the driver doesn't have at least 4 queues, but the
code stopping/waking the virtual interface queues
wasn't taking this into account.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the interfaces were removed just before a restart
work was started, open_count will be 0, and most of
the reconfig work will be skipped, including the
resetting of local->in_reconfig to false.
Leaving local->inconfig = true will result in
dropping any incoming packet.
Fix it by always setting local->in_reconfig = false
(even if there are no active interfaces).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the way the default key links are created,
it happens that a link is left dangling:
* both unicast/multicast links are created
* unicast link is destroyed, and the links
are updated
* during this update, adding the multicast
link again fails because it is present,
destroying the debugfs pointer
* removing the multicast link won't work as
the pointer has been destroyed
Fix this by always removing the links and then
re-creating them if needed.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Reported-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
60g band uses different from .11n MCS scheme, so bitrate
should be calculated differently
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Until now, a u16 value was used to represent bitrate value.
With VHT bitrates this becomes too small.
Introduce a new 32-bit bitrate attribute. nl80211 will report
both the new and the old attribute, unless the bitrate doesn't
fit into the old u16 attribute in which case only the new one
will be reported.
User space tools encouraged to prefer the 32-bit attribute, if
available (since it won't be available on older kernels.)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[reword commit message and comments a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal's monitor channel tracking introduce a locking problem
as it locked the rdev lock inside the netdev notifier which
isn't allowed as we might already hold it if we get there by
removing an interface that is up.
Fix this by relying only on the RTNL to protect the interface
counters, the RTNL is always held in these code paths anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers require setup before being able to send
management frames in managed mode, in particular in
multi-channel cases.
Introduce API to allow the drivers to do such setup
while being able to sleep waiting for the setup to
finish in the device. This isn't possible inside the
TX call since that can't sleep.
A future patch may also restructure the TX retry to
wait for the driver to report the frame status, as
suggested by Arik in
http://mid.gmane.org/CA+XVXffKSEL6ZQPQ98x-zO-NL2=TNF1uN==mprRyUmAaRn254g@mail.gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
