With commit d8e8fd0ebf ("mtd: rawnand: denali: decouple controller
and NAND chips"), the Denali NAND controller driver migrated to the
new controller/chip representation.
Update DT for it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add the EMAC's OCP reset property on Arria10. The OCP reset bits are
also needed to correctly bring the EMACs out of reset correctly.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Because of register and bits difference for setting PHY modes, PTP reference
clock, and FPGA signalling, the Arria10 SoC needs to use the
"altr,socfpga-stmmac-a10-s10" binding to set the correct modes.
On Arria10, each EMAC has its own register for PHY modes, and they all have
the same offset, thus we can use the 2nd parameter to specify the offsets
for the FPGA signal bits.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add reset property for gpio, i2c, sdmmc, nand, qspi, spi, uart, and
watchdog on base socfpga and socfpga_arria10.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Follow the recent trend for the license description.
This is also in an effort to fully sync the devicetrees with U-Boot.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The address in the SDRAM node was incorrect. Fix this to agree with the
correct address and to match the reg definition block.
Cc: stable@vger.kernel.org
Fixes: 54b4a8f57848b("arm: socfpga: dts: Add Arria10 SDRAM EDAC DTS support")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add the resets property for all the timers on the Cyclone5/Arria5/Arria10
platforms.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The NAND IP needs 3 clocks(nand_x_clk, nand_clk, and nand_ecc_clk). This
patch adds a nand_clk, which is derived from the nand_x_clk, but has a
fixed divider of 4, and the nand_ecc_clk, which is derived from the
nand_x_clk.
Update the NAND node to use the additional clocks.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2: add nand_ecc_clk and update commit message
Remove the unused bus-num node and change num-chipselect
to num-cs to match SPI bindings.
Cc: stable@vger.kernel.org
Fixes: f2d6f8f817 ("ARM: dts: socfpga: Add SPI Master1 for Arria10 SR chip")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The NAND compatible "denali,denal-nand-dt" property has never been used and
is obsolete. Remove it.
Cc: stable@vger.kernel.org
Fixes: f549af06e9b6("ARM: dts: socfpga: Add NAND device tree for Arria10")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The skeleton.dtsi file is now deprecated as noted in commit 9c0da3cc61
("ARM: dts: explicitly mark skeleton.dtsi as deprecated"). The SoCFPGA
device trees already contain the nodes that are defined in skeleton.dtsi
(#address-cells, #size-cells, chosen, aliases, memory).
Including skeleton.dtsi is useless and will produce the following
warning when compiled with W=1:
Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Node eccmgr has a unit name, but do not have a reg property as only the
child nodes do have this property. Likewise the usbphy node do not have
a reg property. This will trigger the following warnings when compiled
with W=1:
Node /soc/eccmgr@ffd08140 has a unit name, but no reg property
Node /soc/usbphy@0 has a unit name, but no reg property
Remove the superfluous unit names.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Most clock nodes in Arria5, Cyclone5 and Arria10 have a reg property but
does not have a unit name. This will trigger several warnings like this
one (when compiled with W=1):
Node /soc/clkmgr@ffd04000/clocks/periph_pll has a reg or ranges
property, but no unit name
Add the corresponding unit name to each node.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add the device tree entries needed to support the EMAC AXI
bus settings on the Arria10 SoCFPGA chip.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add the base FPGA region for DT overlay support in FPGA programming.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Matthew Gerlach <mgerlach@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add the Altera Arria10 SPI Master Node in preparation for
the A10SR MFD node.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Enable the bit(22) shared-override bit for the SoCFPGA family. While at it,
enable the prefetch-data and prefetch-instr settings for the Arria10.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Device tree contents continue to be the largest branches we submit. This
time around, some of the contents worth pointing out is:
- New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large delta due
to indentation changes
- A new Tegra K1 board: Apalis
- A bunch of small updates to many Allwinner platforms; new hardware support,
some cleanup, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C4NU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Device tree contents continue to be the largest branches we submit.
This time around, some of the contents worth pointing out is:
New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large
delta due to indentation changes
- a new Tegra K1 board: Apalis
- a bunch of small updates to many Allwinner platforms; new hardware
support, some cleanup, etc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
...
The notion of which uart instance is serial0 or serial1
is board specific rather than generic to the chip. This
patch removes the serial aliases from generic chip dtsi
and adds an appropriate alias to the board specific dtsi.
By making the alias for serial0 point to uart1 for the arria10_socdk,
the linux boot command line supports specifying console=ttyS0,115200
for backwards compatibility, and it supports not specifying
the console at all.
Signed-off-by: Matthew Gerlach <mgerlach@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Changes to support IRQ controller implementation including adding
new property irq-controller to eccmgr and adding IRQ property
to children.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add the device tree entries needed to support the Altera On-Chip
RAM EDAC on the Arria10 chip.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add the device tree entries needed to support the Altera L2
cache EDAC on the Arria10 chip.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The PL330 DMA driver will not load on Arria10 without devicetree entries
for clocks and clock_names. This patch adds those entries. It also adds
the ninth interrupt, which is required for error detection.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The CIU clock for the SD/MMC should be the sdmmc_clk and not the
sdmmc_free_clk. Also, add the correct phase shift the sdmmc_clk.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The compatible string "simple-bus" is well defined in ePAPR, while
I see no documentation for the "arm,amba-bus" arnywhere in ePAPR or
Documentation/devicetree/.
DT is also used by other projects than Linux kernel. It is not a
good idea to rely on such an unofficial binding.
This commit
- replaces "arm,amba-bus" with "simple-bus"
- drops "arm,amba-bus" where it is used along with "simple-bus"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the required clock fields for all the I2C nodes. Also add missing clock
fields for UART0 and USB1.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
- Add DTS property "altr,modrst-offset" for reset driver to
use
- Add updated reset defines for the reset driver
- Add reset property for EMACs on Arria10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dKt6
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_for_v4.3_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS updates for v4.3, take 2
- Add DTS property "altr,modrst-offset" for reset driver to
use
- Add updated reset defines for the reset driver
- Add reset property for EMACs on Arria10
* tag 'socfpga_dts_for_v4.3_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: dts: Add resets for EMACs on Arria10
ARM: socfpga: dts: add "altr,modrst-offset" property
dt-bindings: Add reset manager offsets for Arria10
Signed-off-by: Olof Johansson <olof@lixom.net>
The "altr,modrst-offset" property represents the offset into the reset manager
that is the first register to be used by the driver to bring peripherals out
of reset.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
As usual, quite a few device-tree updates in ARM land. There was ome
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wWIc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Kevin Hilman:
"As usual, quite a few device-tree updates in ARM land. There was one
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS
RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill
SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33,
Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (462 commits)
ARM: hisi: revert changes from hisi/hip04-dt branch
ARM: nomadik: set proper compatible for accelerometer
ARM64: juno: add GPIO keys
ARM: at91/dt: sama5d4: fix dma conf for aes, sha and tdes nodes
ARM: dts: Introduce STM32F429 MCU
ARM: socfpga: dts: enable ethernet for Arria10 devkit
ARM: dts: k2l: fix the netcp range size
ARM: dts: k2e: fix the netcp range size
ARM: dts: k2hk: fix the netcp range size
ARM: dts: k2l-evm: Add device bindings for netcp driver
ARM: dts: k2e-evm: Add device bindings for netcp driver
ARM: dts: k2hk-evm: Add device bindings for netcp driver
ARM: BCM5301X: Add DT for Asus RT-AC87U
ARM: BCM5301X: add IRQ numbers for PCIe controller
ARM: BCM5301X: add NAND flash chip description
arm64: dts: Add dts files for Hisilicon Hi6220 SoC
clk: hi6220: Document devicetree bindings for hi6220 clock
arm64: hi6220: Document devicetree bindings for Hisilicon hi6220 SoC
ARM: at91/dt: sama5d4ek: mci0 uses slot 0
ARM: at91/dt: kizbox: fix mismatch LED PWM device
...
Update the arria10 gmac nodes with all the necessary properties for ethernet
to function on the Arria10 devkit.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Dinh Nguyen