commit 0c5aae5927 upstream.
The serdev tty-port controller driver should reset the tty-port client
operations also on deregistration to avoid a NULL-pointer dereference in
case the port is later re-registered as a normal tty device.
Note that this can only happen with tty drivers such as 8250 which have
statically allocated port structures that can end up being reused and
where a later registration would not register a serdev controller (e.g.
due to registration errors or if the devicetree has been changed in
between).
Specifically, this can be an issue for any statically defined ports that
would be registered by 8250 core when an 8250 driver is being unbound.
Fixes: bed35c6dfa ("serdev: add a tty port controller driver")
Cc: stable <stable@vger.kernel.org> # 4.11
Reported-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200210145730.22762-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 679aac5ead upstream.
RX cancel command fails when BT is switched on and off multiple times.
To handle this, poll for the cancel bit in SE_GENI_S_IRQ_STATUS register
instead of SE_GENI_S_CMD_CTRL_REG.
As per the HPG update, handle the RX last bit after cancel command
and flush out the RX FIFO buffer.
Signed-off-by: satya priya <skakit@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1581415982-8793-1-git-send-email-skakit@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04b5bfe3dc upstream.
In atmel_shutdown() we call atmel_stop_rx() and atmel_stop_tx() functions.
Prevent the rx restart that is implemented in RS485 or ISO7816 modes when
calling atmel_stop_tx() by using the atomic information tasklet_shutdown
that is already in place for this purpose.
Fixes: 98f2082c3a ("tty/serial: atmel: enforce tasklet init and termination sequences")
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210152053.8289-1-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7febbcbc48 upstream.
The commit 54e53b2e80
("tty: serial: 8250: pass IRQ shared flag to UART ports")
nicely explained the problem:
---8<---8<---
On some systems IRQ lines between multiple UARTs might be shared. If so, the
irqflags have to be configured accordingly. The reason is: The 8250 port startup
code performs IRQ tests *before* the IRQ handler for that particular port is
registered. This is performed in serial8250_do_startup(). This function checks
whether IRQF_SHARED is configured and only then disables the IRQ line while
testing.
This test is performed upon each open() of the UART device. Imagine two UARTs
share the same IRQ line: On is already opened and the IRQ is active. When the
second UART is opened, the IRQ line has to be disabled while performing IRQ
tests. Otherwise an IRQ might handler might be invoked, but the IRQ itself
cannot be handled, because the corresponding handler isn't registered,
yet. That's because the 8250 code uses a chain-handler and invokes the
corresponding port's IRQ handling routines himself.
Unfortunately this IRQF_SHARED flag isn't configured for UARTs probed via device
tree even if the IRQs are shared. This way, the actual and shared IRQ line isn't
disabled while performing tests and the kernel correctly detects a spurious
IRQ. So, adding this flag to the DT probe solves the issue.
Note: The UPF_SHARE_IRQ flag is configured unconditionally. Therefore, the
IRQF_SHARED flag can be set unconditionally as well.
Example stack trace by performing `echo 1 > /dev/ttyS2` on a non-patched system:
|irq 85: nobody cared (try booting with the "irqpoll" option)
| [...]
|handlers:
|[<ffff0000080fc628>] irq_default_primary_handler threaded [<ffff00000855fbb8>] serial8250_interrupt
|Disabling IRQ #85
---8<---8<---
But unfortunately didn't fix the root cause. Let's try again here by moving
IRQ flag assignment from serial_link_irq_chain() to serial8250_do_startup().
This should fix the similar issue reported for 8250_pnp case.
Since this change we don't need to have custom solutions in 8250_aspeed_vuart
and 8250_of drivers, thus, drop them.
Fixes: 1c2f04937b ("serial: 8250: add IRQ trigger support")
Reported-by: Li RongQing <lirongqing@baidu.com>
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20200211135559.85960-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21b5ee59ef upstream.
Commit
aaf248848d ("perf/x86/msr: Add AMD IRPERF (Instructions Retired)
performance counter")
added support for access to the free-running counter via 'perf -e
msr/irperf/', but when exercised, it always returns a 0 count:
BEFORE:
$ perf stat -e instructions,msr/irperf/ true
Performance counter stats for 'true':
624,833 instructions
0 msr/irperf/
Simply set its enable bit - HWCR bit 30 - to make it start counting.
Enablement is restricted to all machines advertising IRPERF capability,
except those susceptible to an erratum that makes the IRPERF return
bad values.
That erratum occurs in Family 17h models 00-1fh [1], but not in F17h
models 20h and above [2].
AFTER (on a family 17h model 31h machine):
$ perf stat -e instructions,msr/irperf/ true
Performance counter stats for 'true':
621,690 instructions
622,490 msr/irperf/
[1] Revision Guide for AMD Family 17h Models 00h-0Fh Processors
[2] Revision Guide for AMD Family 17h Models 30h-3Fh Processors
The revision guides are available from the bugzilla Link below.
[ bp: Massage commit message. ]
Fixes: aaf248848d ("perf/x86/msr: Add AMD IRPERF (Instructions Retired) performance counter")
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206537
Link: http://lkml.kernel.org/r/20200214201805.13830-1-kim.phillips@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51dede9c05 upstream.
Accessing the MCA thresholding controls in sysfs concurrently with CPU
hotplug can lead to a couple of KASAN-reported issues:
BUG: KASAN: use-after-free in sysfs_file_ops+0x155/0x180
Read of size 8 at addr ffff888367578940 by task grep/4019
and
BUG: KASAN: use-after-free in show_error_count+0x15c/0x180
Read of size 2 at addr ffff888368a05514 by task grep/4454
for example. Both result from the fact that the threshold block
creation/teardown code frees the descriptor memory itself instead of
defining proper ->release function and leaving it to the driver core to
take care of that, after all sysfs accesses have completed.
Do that and get rid of the custom freeing code, fixing the above UAFs in
the process.
[ bp: write commit message. ]
Fixes: 9526866439 ("[PATCH] x86_64: mce_amd support for family 0x10 processors")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200214082801.13836-1-bp@alien8.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e5cf31fbe upstream.
threshold_create_bank() creates a bank descriptor per MCA error
thresholding counter which can be controlled over sysfs. It publishes
the pointer to that bank in a per-CPU variable and then goes on to
create additional thresholding blocks if the bank has such.
However, that creation of additional blocks in
allocate_threshold_blocks() can fail, leading to a use-after-free
through the per-CPU pointer.
Therefore, publish that pointer only after all blocks have been setup
successfully.
Fixes: 019f34fccf ("x86, MCE, AMD: Move shared bank to node descriptor")
Reported-by: Saar Amar <Saar.Amar@microsoft.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200128140846.phctkvx5btiexvbx@kili.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff5ac61ee8 upstream.
The IMA arch code attempts to inspect the "SetupMode" EFI variable
by populating a variable called efi_SetupMode_name with the string
"SecureBoot" and passing that to the EFI GetVariable service, which
obviously does not yield the expected result.
Given that the string is only referenced a single time, let's get
rid of the intermediate variable, and pass the correct string as
an immediate argument. While at it, do the same for "SecureBoot".
Fixes: 399574c64e ("x86/ima: retry detecting secure boot mode")
Fixes: 980ef4d22a ("x86/ima: check EFI SetupMode too")
Cc: Matthew Garrett <mjg59@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: stable@vger.kernel.org # v5.3
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0022c0ef2 upstream.
Add brackets around the evaluation of the 'addr' parameter to the
untagged_addr() macro so that the cast to 'u64' applies to the result
of the expression.
Cc: <stable@vger.kernel.org>
Fixes: 597399d0cb ("arm64: tags: Preserve tags for addresses translated via TTBR1")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50a175dd18 upstream.
With HW assistance all page tables must be 4k aligned, the 8xx drops
the last 12 bits during the walk.
Redefine HUGEPD_SHIFT_MASK to mask last 12 bits out. HUGEPD_SHIFT_MASK
is used to for alignment of page table cache.
Fixes: 22569b881d ("powerpc/8xx: Enable 8M hugepage support with HW assistance")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/778b1a248c4c7ca79640eeff7740044da6a220a0.1581264115.git.christophe.leroy@c-s.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2b67ef90b upstream.
Commit 55c8fc3f49 ("powerpc/8xx: reintroduce 16K pages with HW
assistance") redefined pte_t as a struct of 4 pte_basic_t, because
in 16K pages mode there are four identical entries in the
page table. But the size of hugepage tables is calculated based
of the size of (void *). Therefore, we end up with page tables
of size 1k instead of 4k for 512k pages.
As 512k hugepage tables are the same size as standard page tables,
ie 4k, use the standard page tables instead of PGT_CACHE tables.
Fixes: 3fb69c6a1a ("powerpc/8xx: Enable 512k hugepage support with HW assistance")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/90ec56a2315be602494619ed0223bba3b0b8d619.1580997007.git.christophe.leroy@c-s.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2464cc4c34 upstream.
After a treclaim, we expect to be in non-transactional state. If we
don't clear the current thread's MSR[TS] before we get preempted, then
tm_recheckpoint_new_task() will recheckpoint and we get rescheduled in
suspended transaction state.
When handling a signal caught in transactional state,
handle_rt_signal64() calls get_tm_stackpointer() that treclaims the
transaction using tm_reclaim_current() but without clearing the
thread's MSR[TS]. This can cause the TM Bad Thing exception below if
later we pagefault and get preempted trying to access the user's
sigframe, using __put_user(). Afterwards, when we are rescheduled back
into do_page_fault() (but now in suspended state since the thread's
MSR[TS] was not cleared), upon executing 'rfid' after completion of
the page fault handling, the exception is raised because a transition
from suspended to non-transactional state is invalid.
Unexpected TM Bad Thing exception at c00000000000de44 (msr 0x8000000302a03031) tm_scratch=800000010280b033
Oops: Unrecoverable exception, sig: 6 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
CPU: 25 PID: 15547 Comm: a.out Not tainted 5.4.0-rc2 #32
NIP: c00000000000de44 LR: c000000000034728 CTR: 0000000000000000
REGS: c00000003fe7bd70 TRAP: 0700 Not tainted (5.4.0-rc2)
MSR: 8000000302a03031 <SF,VEC,VSX,FP,ME,IR,DR,LE,TM[SE]> CR: 44000884 XER: 00000000
CFAR: c00000000000dda4 IRQMASK: 0
PACATMSCRATCH: 800000010280b033
GPR00: c000000000034728 c000000f65a17c80 c000000001662800 00007fffacf3fd78
GPR04: 0000000000001000 0000000000001000 0000000000000000 c000000f611f8af0
GPR08: 0000000000000000 0000000078006001 0000000000000000 000c000000000000
GPR12: c000000f611f84b0 c00000003ffcb200 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 c000000f611f8140
GPR24: 0000000000000000 00007fffacf3fd68 c000000f65a17d90 c000000f611f7800
GPR28: c000000f65a17e90 c000000f65a17e90 c000000001685e18 00007fffacf3f000
NIP [c00000000000de44] fast_exception_return+0xf4/0x1b0
LR [c000000000034728] handle_rt_signal64+0x78/0xc50
Call Trace:
[c000000f65a17c80] [c000000000034710] handle_rt_signal64+0x60/0xc50 (unreliable)
[c000000f65a17d30] [c000000000023640] do_notify_resume+0x330/0x460
[c000000f65a17e20] [c00000000000dcc4] ret_from_except_lite+0x70/0x74
Instruction dump:
7c4ff120 e8410170 7c5a03a6 38400000 f8410060 e8010070 e8410080 e8610088
60000000 60000000 e8810090 e8210078 <4c000024> 48000000 e8610178 88ed0989
---[ end trace 93094aa44b442f87 ]---
The simplified sequence of events that triggers the above exception is:
... # userspace in NON-TRANSACTIONAL state
tbegin # userspace in TRANSACTIONAL state
signal delivery # kernelspace in SUSPENDED state
handle_rt_signal64()
get_tm_stackpointer()
treclaim # kernelspace in NON-TRANSACTIONAL state
__put_user()
page fault happens. We will never get back here because of the TM Bad Thing exception.
page fault handling kicks in and we voluntarily preempt ourselves
do_page_fault()
__schedule()
__switch_to(other_task)
our task is rescheduled and we recheckpoint because the thread's MSR[TS] was not cleared
__switch_to(our_task)
switch_to_tm()
tm_recheckpoint_new_task()
trechkpt # kernelspace in SUSPENDED state
The page fault handling resumes, but now we are in suspended transaction state
do_page_fault() completes
rfid <----- trying to get back where the page fault happened (we were non-transactional back then)
TM Bad Thing # illegal transition from suspended to non-transactional
This patch fixes that issue by clearing the current thread's MSR[TS]
just after treclaim in get_tm_stackpointer() so that we stay in
non-transactional state in case we are preempted. In order to make
treclaim and clearing the thread's MSR[TS] atomic from a preemption
perspective when CONFIG_PREEMPT is set, preempt_disable/enable() is
used. It's also necessary to save the previous value of the thread's
MSR before get_tm_stackpointer() is called so that it can be exposed
to the signal handler later in setup_tm_sigcontexts() to inform the
userspace MSR at the moment of the signal delivery.
Found with tm-signal-context-force-tm kernel selftest.
Fixes: 2b0a576d15 ("powerpc: Add new transactional memory state to the signal context")
Cc: stable@vger.kernel.org # v3.9
Signed-off-by: Gustavo Luiz Duarte <gustavold@linux.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200211033831.11165-1-gustavold@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4f194ed9e upstream.
Recovering a dead PHB can currently cause a deadlock as the PCI
rescan/remove lock is taken twice.
This is caused as part of an existing bug in
eeh_handle_special_event(). The pe is processed while traversing the
PHBs even though the pe is unrelated to the loop. This causes the pe
to be, incorrectly, processed more than once.
Untangling this section can move the pe processing out of the loop and
also outside the locked section, correcting both problems.
Fixes: 2e25505147 ("powerpc/eeh: Fix crash when edev->pdev changes")
Cc: stable@vger.kernel.org # 5.4+
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Tested-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/0547e82dbf90ee0729a2979a8cac5c91665c621f.1581051445.git.sbobroff@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4031afb9d upstream.
In ITLB miss handled the line supposed to clear bits 20-23 on the L2
ITLB entry is buggy and does indeed nothing, leading to undefined
value which could allow execution when it shouldn't.
Properly do the clearing with the relevant instruction.
Fixes: 74fabcadfd ("powerpc/8xx: don't use r12/SPRN_SPRG_SCRATCH2 in TLB Miss handlers")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/4f70c2778163affce8508a210f65d140e84524b4.1581272050.git.christophe.leroy@c-s.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dde2bb2da0 upstream.
We need to use the AS attached to the opened FD when dumping counters.
Reported-by: Antonio Caggiano <antonio.caggiano@collabora.com>
Fixes: 7282f7645d ("drm/panfrost: Implement per FD address spaces")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Tested-by: Antonio Caggiano <antonio.caggiano@collabora.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200206141327.446127-1-boris.brezillon@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23954cb078 upstream.
In routine wpa_supplicant_ioctl(), the user-controlled p->length is
checked to be at least the size of struct ieee_param size, but the code
does not detect the case where p->length is greater than the size
of the struct, thus a malicious user could be wasting kernel memory.
Fixes commit 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver").
Reported by: Pietro Oliva <pietroliva@gmail.com>
Cc: Pietro Oliva <pietroliva@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver").
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/r/20200210180235.21691-5-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac33597c0c upstream.
In routine rtw_hostapd_ioctl(), the user-controlled p->length is assumed
to be at least the size of struct ieee_param size, but this assumption is
never checked. This could result in out-of-bounds read/write on kernel
heap in case a p->length less than the size of struct ieee_param is
specified by the user. If p->length is allowed to be greater than the size
of the struct, then a malicious user could be wasting kernel memory.
Fixes commit 554c0a3abf ("0taging: Add rtl8723bs sdio wifi driver").
Reported by: Pietro Oliva <pietroliva@gmail.com>
Cc: Pietro Oliva <pietroliva@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Fixes 554c0a3abf ("0taging: Add rtl8723bs sdio wifi driver").
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/r/20200210180235.21691-3-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ddf8ab8d1 upstream.
In routine wpa_supplicant_ioctl(), the user-controlled p->length is
checked to be at least the size of struct ieee_param size, but the code
does not detect the case where p->length is greater than the size
of the struct, thus a malicious user could be wasting kernel memory.
Fixes commit a2c60d42d9 ("Add files for new driver - part 16").
Reported by: Pietro Oliva <pietroliva@gmail.com>
Cc: Pietro Oliva <pietroliva@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Fixes commit a2c60d42d9 ("Add files for new driver - part 16").
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/r/20200210180235.21691-4-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 499c405b2b upstream.
In routine rtw_hostapd_ioctl(), the user-controlled p->length is assumed
to be at least the size of struct ieee_param size, but this assumption is
never checked. This could result in out-of-bounds read/write on kernel
heap in case a p->length less than the size of struct ieee_param is
specified by the user. If p->length is allowed to be greater than the size
of the struct, then a malicious user could be wasting kernel memory.
Fixes commit a2c60d42d9 ("Add files for new driver - part 16").
Reported by: Pietro Oliva <pietroliva@gmail.com>
Cc: Pietro Oliva <pietroliva@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Fixes: a2c60d42d9 ("staging: r8188eu: Add files for new driver - part 16")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/r/20200210180235.21691-2-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c14335ebb9 upstream.
Commit 83f85b8ec3 postponed the percpu_ref_put(&se_cmd->se_lun->lun_ref)
call from command completion to the time when the final command reference
is dropped. That approach is not compatible with the iSCSI target driver
because the iSCSI target driver keeps the command with the highest stat_sn
after it has completed until the next command is received (see also
iscsit_ack_from_expstatsn()). Fix this regression by reverting commit
83f85b8ec3.
Fixes: 83f85b8ec3 ("scsi: target/core: Inline transport_lun_remove_cmd()")
Cc: Pavel Zakharov <pavel.zakharov@delphix.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210051202.12934-1-bvanassche@acm.org
Reported-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b32196e35b upstream.
Currently the string formatting is mixing up the offset of ret and
len. Re-work the code to use just len, remove ret and use scnprintf
instead of snprintf and len position accumulation where required.
Remove the -ve return check since scnprintf never returns a failure
-ve size. Also break overly long lines to clean up checkpatch
warnings.
Addresses-Coverity: ("Unused value")
Fixes: 1381a5113c ("usb: dwc3: debug: purge usage of strcat")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210095139.328711-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ee858975b upstream.
The current code in dwc3_gadget_ep_reclaim_completed_trb() will
check for IOC/LST bit in the event->status and returns if
IOC/LST bit is set. This logic doesn't work if multiple TRBs
are queued per request and the IOC/LST bit is set on the last
TRB of that request.
Consider an example where a queued request has multiple queued
TRBs and IOC/LST bit is set only for the last TRB. In this case,
the core generates XferComplete/XferInProgress events only for
the last TRB (since IOC/LST are set only for the last TRB). As
per the logic in dwc3_gadget_ep_reclaim_completed_trb()
event->status is checked for IOC/LST bit and returns on the
first TRB. This leaves the remaining TRBs left unhandled.
Similarly, if the gadget function enqueues an unaligned request
with sglist already in it, it should fail the same way, since we
will append another TRB to something that already uses more than
one TRB.
To aviod this, this patch changes the code to check for IOC/LST
bits in TRB->ctrl instead.
At a practical level, this patch resolves USB transfer stalls seen
with adb on dwc3 based HiKey960 after functionfs gadget added
scatter-gather support around v4.20.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Cc: stable <stable@vger.kernel.org>
Tested-by: Tejas Joglekar <tejas.joglekar@synopsys.com>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
[jstultz: forward ported to mainline, reworded commit log, reworked
to only check trb->ctrl as suggested by Felipe]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a0d6f7c0a upstream.
SET/CLEAR_FEATURE for Remote Wakeup allowance not handled correctly.
GET_STATUS handling provided not correct data on DATA Stage.
Issue seen when gadget's dr_mode set to "otg" mode and connected
to MacOS.
Both are fixed and tested using USBCV Ch.9 tests.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Fixes: fa389a6d77 ("usb: dwc2: gadget: Add remote_wakeup_allowed flag")
Tested-by: Jack Mitchell <ml@embed.me.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1208f9e1d7 upstream.
Renesas R-Car H3ULCB + Kingfisher Infotainment Board is either not able
to detect the USB3.0 mass storage devices or is detecting those as
USB2.0 high speed devices.
The explanation given by Renesas is that, due to a HW issue, the XHCI
driver does not wake up after going to sleep on connecting a USB3.0
device.
In order to mitigate that, disable the auto-suspend feature
specifically for SMSC hubs from hub_probe() function, as a quirk.
Renesas Kingfisher Infotainment Board has two USB3.0 ports (CN2) which
are connected via USB5534B 4-port SuperSpeed/Hi-Speed, low-power,
configurable hub controller.
[1] SanDisk USB 3.0 device detected as USB-2.0 before the patch
[ 74.036390] usb 5-1.1: new high-speed USB device number 4 using xhci-hcd
[ 74.061598] usb 5-1.1: New USB device found, idVendor=0781, idProduct=5581, bcdDevice= 1.00
[ 74.069976] usb 5-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 74.077303] usb 5-1.1: Product: Ultra
[ 74.080980] usb 5-1.1: Manufacturer: SanDisk
[ 74.085263] usb 5-1.1: SerialNumber: 4C530001110208116550
[2] SanDisk USB 3.0 device detected as USB-3.0 after the patch
[ 34.565078] usb 6-1.1: new SuperSpeed Gen 1 USB device number 3 using xhci-hcd
[ 34.588719] usb 6-1.1: New USB device found, idVendor=0781, idProduct=5581, bcdDevice= 1.00
[ 34.597098] usb 6-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 34.604430] usb 6-1.1: Product: Ultra
[ 34.608110] usb 6-1.1: Manufacturer: SanDisk
[ 34.612397] usb 6-1.1: SerialNumber: 4C530001110208116550
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1580989763-32291-1-git-send-email-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8099f58f1e upstream.
Paul Zimmerman reports that his USB Bluetooth adapter sometimes
crashes following system resume, when it receives a
Get-Device-Descriptor request while it is busy doing something else.
Such a request was added by commit a4f55d8b8c ("usb: hub: Check
device descriptor before resusciation"). It gets sent when the hub
driver's work thread checks whether a connect-change event on an
enabled port really indicates a new device has been connected, as
opposed to an old device momentarily disconnecting and then
reconnecting (which can happen with xHCI host controllers, since they
automatically enable connected ports).
The same kind of thing occurs when a port's power session is lost
during system suspend. When the system wakes up it sees a
connect-change event on the port, and if the child device's
persist_enabled flag was set then hub_activate() sets the device's
reset_resume flag as well as the port's bit in hub->change_bits. The
reset-resume code then takes responsibility for checking that the same
device is still attached to the port, and it does this as part of the
device's resume pathway. By the time the hub driver's work thread
starts up again, the device has already been fully reinitialized and
is busy doing its own thing. There's no need for the work thread to
do the same check a second time, and in fact this unnecessary check is
what caused the problem that Paul observed.
Note that performing the unnecessary check is not actually a bug.
Devices are supposed to be able to send descriptors back to the host
even when they are busy doing something else. The underlying cause of
Paul's problem lies in his Bluetooth adapter. Nevertheless, we
shouldn't perform the same check twice in a row -- and as a nice side
benefit, removing the extra check allows the Bluetooth adapter to work
more reliably.
The work thread performs its check when it sees that the port's bit is
set in hub->change_bits. In this situation that bit is interpreted as
though a connect-change event had occurred on the port _after_ the
reset-resume, which is not what actually happened.
One possible fix would be to make the reset-resume code clear the
port's bit in hub->change_bits. But it seems simpler to just avoid
setting the bit during hub_activate() in the first place. That's what
this patch does.
(Proving that the patch is correct when CONFIG_PM is disabled requires
a little thought. In that setting hub_activate() will be called only
for initialization and resets, since there won't be any resumes or
reset-resumes. During initialization and hub resets the hub doesn't
have any child devices, and so this code path never gets executed.)
Reported-and-tested-by: Paul Zimmerman <pauldzim@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://marc.info/?t=157949360700001&r=1&w=2
CC: David Heinzelmann <heinzelmann.david@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001311037460.1577-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b692056db8 upstream.
Currently, the SourceControl will stay in power-down mode after resuming
from suspend. This patch resets the device after suspend to power it up.
Signed-off-by: Richard Dodd <richard.o.dodd@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200212142220.36892-1-richard.o.dodd@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e99862c05 upstream.
When a uas disk is plugged into an external hub, uas_probe()
will be called by the hub thread to do the probe. It will
first create a SCSI host and then do the scan for this host.
During the scan, it will probe the LUN using SCSI INQUERY command
which will be packed in the URB and submitted to uas disk.
There might be a chance that this external hub with uas disk
attached is unplugged during the scan. In this case, uas driver
will fail to submit the URB (due to the NOTATTACHED state of uas
device) and try to put this SCSI command back to request queue
waiting for next chance to run.
In normal case, this cycle will terminate when hub thread gets
disconnection event and calls into uas_disconnect() accordingly.
But in this case, uas_disconnect() will not be called because
hub thread of external hub gets stuck waiting for the completion
of this SCSI command. A deadlock happened.
In this fix, uas will call scsi_scan_host() asynchronously to
avoid the blocking of hub thread.
Signed-off-by: EJ Hsu <ejh@nvidia.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200130092506.102760-1-ejh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73f8bda9b5 upstream.
Add a new device quirk that can be used to blacklist endpoints.
Since commit 3e4f8e21c4 ("USB: core: fix check for duplicate
endpoints") USB core ignores any duplicate endpoints found during
descriptor parsing.
In order to handle devices where the first interfaces with duplicate
endpoints are the ones that should have their endpoints ignored, we need
to add a blacklist.
Tested-by: edes <edes@gmx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200203153830.26394-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc0ffbea57 upstream.
On some situations, the software handles TRB events slower
than adding TRBs, then xhci_handle_event can't return zero
long time, the xHC will consider the event ring is full,
and trigger "Event Ring Full" error, but in fact, the software
has already finished lots of events, just no chance to
update ERDP (event ring dequeue pointer).
In this commit, we force update ERDP if half of TRBS_PER_SEGMENT
events have handled to avoid "Event Ring Full" error.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1573836603-10871-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf0ee7c60c upstream.
xhci driver assumed that xHC controllers have at most one custom
supported speed table (PSI) for all usb 3.x ports.
Memory was allocated for one PSI table under the xhci hub structure.
Turns out this is not the case, some controllers have a separate
"supported protocol capability" entry with a PSI table for each port.
This means each usb3 roothub port can in theory support different custom
speeds.
To solve this, cache all supported protocol capabilities with their PSI
tables in an array, and add pointers to the xhci port structure so that
every port points to its capability entry in the array.
When creating the SuperSpeedPlus USB Device Capability BOS descriptor
for the xhci USB 3.1 roothub we for now will use only data from the
first USB 3.1 capable protocol capability entry in the array.
This could be improved later, this patch focuses resolving
the memory leak.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Fixes: 47189098f8 ("xhci: parse xhci protocol speed ID list for usb 3.1 usage")
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200211150158.14475-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 024d411e9c upstream.
Intel hosts that need the XHCI_PME_STUCK_QUIRK flag should enable
runtime pm by calling xhci_pme_acpi_rtd3_enable() before
usb_hcd_pci_probe() calls pci_dev_run_wake().
Otherwise usage count for the device won't be decreased, and runtime
suspend is prevented.
usb_hcd_pci_probe() only decreases the usage count if device can
generate run-time wake-up events, i.e. when pci_dev_run_wake()
returns true.
This issue was exposed by pci_dev_run_wake() change in
commit 8feaec33b9 ("PCI / PM: Always check PME wakeup capability for
runtime wakeup support")
and should be backported to kernels with that change
Cc: <stable@vger.kernel.org> # 4.13+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f148b9f402 upstream.
A Full-speed bulk USB audio device (DJ-Tech CTRL) with a invalid Maximum
Packet Size of 4 causes a xHC "Parameter Error" at enumeration.
This is because valid Maximum packet sizes for Full-speed bulk endpoints
are 8, 16, 32 and 64 bytes. Hosts are not required to support other values
than these. See usb 2 specs section 5.8.3 for details.
The device starts working after forcing the maximum packet size to 8.
This is most likely the case with other devices as well, so force the
maximum packet size to a valid range.
Cc: stable@vger.kernel.org
Reported-by: Rene D Obermueller <cmdrrdo@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93134df520 upstream.
bb_pre_ed_rssi is an u8 rx_dm always returns negative signed
values add minus operator to always yield positive.
fixes issue where rx sensitivity is always set to maximum because
the unsigned numbers were always greater then 100.
Fixes: 63b9907f58 ("staging: vt6656: mac80211 conversion: create rx function.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/aceac98c-6e69-3ce1-dfec-2bf27b980221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d67b0290b upstream.
When ashmem file is mmapped, the resulting vma->vm_file points to the
backing shmem file with the generic fops that do not check ashmem
permissions like fops of ashmem do. If an mremap is done on the ashmem
region, then the permission checks will be skipped. Fix that by disallowing
mapping operation on the backing shmem file.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Cc: stable <stable@vger.kernel.org> # 4.4,4.9,4.14,4.18,5.4
Signed-off-by: Todd Kjos <tkjos@google.com>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Link: https://lore.kernel.org/r/20200127235616.48920-1-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 687bff0cd0 upstream.
When pasting a selection to a vt, the task is set as INTERRUPTIBLE while
waiting for a tty to unthrottle. But signals are not handled at all.
Normally, this is not a problem as tty_ldisc_receive_buf receives all
the goods and a user has no reason to interrupt the task.
There are two scenarios where this matters:
1) when the tty is throttled and a signal is sent to the process, it
spins on a CPU until the tty is unthrottled. schedule() does not
really echedule, but returns immediately, of course.
2) when the sel_buffer becomes invalid, KASAN prevents any reads from it
and the loop simply does not proceed and spins forever (causing the
tty to throttle, but the code never sleeps, the same as above). This
sometimes happens as there is a race in the sel_buffer handling code.
So add signal handling to this ioctl (TIOCL_PASTESEL) and return -EINTR
in case a signal is pending.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210081131.23572-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f4ef485be upstream.
Commit a6dbe44275 ("vt: perform safe console erase in the right
order") provided fixes to an earlier commit by gathering all console
scrollback flushing operations in a function of its own. This includes
the invocation of vc_sw->con_switch() as previously done through a
update_screen() call. That commit failed to carry over the
con_is_visible() conditional though, as well as cursor handling, which
caused problems when "\e[3J" was written to a background console.
One could argue for preserving the call to update_screen(). However
this does far more than we need, and it is best to remove scrollback
assumptions from it. Instead let's gather the minimum needed to actually
perform scrollback flushing properly in that one place.
While at it, let's document the vc_sw->con_switch() side effect being
relied upon.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Reported-and-tested-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2001281205560.1655@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e90ca68b0 upstream.
Jordy Zomer reported a KASAN out-of-bounds read in the floppy driver in
wait_til_ready().
Which on the face of it can't happen, since as Willy Tarreau points out,
the function does no particular memory access. Except through the FDCS
macro, which just indexes a static allocation through teh current fdc,
which is always checked against N_FDC.
Except the checking happens after we've already assigned the value.
The floppy driver is a disgrace (a lot of it going back to my original
horrd "design"), and has no real maintainer. Nobody has the hardware,
and nobody really cares. But it still gets used in virtual environment
because it's one of those things that everybody supports.
The whole thing should be re-written, or at least parts of it should be
seriously cleaned up. The 'current fdc' index, which is used by the
FDCS macro, and which is often shadowed by a local 'fdc' variable, is a
prime example of how not to write code.
But because nobody has the hardware or the motivation, let's just fix up
the immediate problem with a nasty band-aid: test the fdc index before
actually assigning it to the static 'fdc' variable.
Reported-by: Jordy Zomer <jordy@simplyhacker.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a702381940 upstream.
This patch is meant to address possible race conditions that can exist
between network configuration and power management. A similar issue was
fixed for igb in commit 9474933caf ("igb: close/suspend race in
netif_device_detach").
In addition it consolidates the code so that the PCI error handling code
will essentially perform the power management freeze on the device prior to
attempting a reset, and will thaw the device afterwards if that is what it
is planning to do. Otherwise when we call close on the interface it should
see it is detached and not attempt to call the logic to down the interface
and free the IRQs again.
From what I can tell the check that was adding the check for __E1000_DOWN
in e1000e_close was added when runtime power management was added. However
it should not be relevant for us as we perform a call to
pm_runtime_get_sync before we call e1000_down/free_irq so it should always
be back up before we call into this anyway.
Reported-by: Morumuri Srivalli <smorumu1@in.ibm.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: David Dai <zdai@linux.vnet.ibm.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bab5417f5f upstream.
Add a new device id for the 100 devie. It has 4 interfaces like the 28
and 28L devices but a larger endpoint so more I/O pins.
Cc: Christoph Jung <jung@codemercs.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200214161148.GA3963518@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f6f8da2d7 upstream.
Add new device ids for the 28 and 28L devices. These have 4 interfaces
instead of 2, but the driver binds the same, so the driver changes are
minimal.
Cc: Christoph Jung <jung@codemercs.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200212040422.2991-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 461d8deb26 upstream.
Add support for two OEM devices that are identical to existing
IO-Warrior devices, except for the USB device id.
Cc: Christoph Jung <jung@codemercs.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200212040422.2991-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03cd45d2e2 upstream.
The driver does not populate .reg_read callback for the non-active NVMem
because the file is supposed to be write-only. However, it turns out
NVMem subsystem does not yet support this and expects that the .reg_read
callback is provided. If user reads the binary attribute it triggers
NULL pointer dereference like this one:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
Call Trace:
bin_attr_nvmem_read+0x64/0x80
kernfs_fop_read+0xa7/0x180
vfs_read+0xbd/0x170
ksys_read+0x5a/0xd0
do_syscall_64+0x43/0x150
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix this in the driver by providing .reg_read callback that always
returns an error.
Reported-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Fixes: e6b245ccd5 ("thunderbolt: Add support for host and device NVM firmware upgrade")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200213095604.1074-1-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd727173e4 upstream.
If we're allocating a logged extent we attempt to insert an extent
record for the file extent directly. We increase
space_info->bytes_reserved, because the extent entry addition will call
btrfs_update_block_group(), which will convert the ->bytes_reserved to
->bytes_used. However if we fail at any point while inserting the
extent entry we will bail and leave space on ->bytes_reserved, which
will trigger a WARN_ON() on umount. Fix this by pinning the space if we
fail to insert, which is what happens in every other failure case that
involves adding the extent entry.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jani Nikula