Modules: HDA Codec driver,HDA generic driver
- Make bound controls global to all patches
- Clean up analog patches (for the upcoming extension to AD1988)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the code for supporting eight cards from the integrated
controller drivers because There Can Be Only One controller of
each type per mainboard.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: HDA Intel driver
This patch is to make the Intel HDA code work for NVIDIA azalia controller.
Modified by Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod G. <vinodg@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Mark the ALC882 'LFE Playback Switch' as an input, like the other
playback switch settings.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Fix a typo (cut & paste) in the alc880_test_mixer structure.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
The ALC260 'Mono Playback Switch' is marked as an output in
patch_realtek.c. It actually does not work unless it is marked as an
input. Go figure... This was tested and confirmed on an HP xw4300.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Intel driver
Disable the auto-correction of DMA position temporarily.
It doesn't work as expected yet...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver,HDA Intel driver,HDA generic driver
Assign audio PCMs first before modem PCMs.
The modem stream is assigned up to device #6, to be consistent over
different models.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Intel driver
Check the validity of the current DMA position when position_fix=0 (auto)
is set. If the DMA position overcomes the threshold, the driver changes
the fix behavior automatically to use POSBUF.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Add the subsystem PCI devid to the list (on top of 2.6.13).
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Intel driver
Fix and clean up for the support of ULI M5461
- set CORB/RIRB sizes explicitly
- add workarounds for ULI on ia32
- max number of streams depends on the chip type now
- increase the size of BDL
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
The insertion of the rate 9600 make a shift in detection of supported
rate, put this rate at the end of the list.
Signed-off-by: Nicolas Graziano <nicolas.graziano@wanadoo.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Intel driver
- removed SNDRV_PCM_INFO_RESUME (the driver cannot do PCM resume at the time)
- fixed chip->pcm_devs initialization
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
CMI8330 driver,ENS1370/1+ driver,FM801 driver,VIA82xx driver,AC97 Codec
ALI5451 driver,CS46xx driver,EMU10K1/EMU10K2 driver,HDA Codec driver
ICE1712 driver,ICE1724 driver
Where appropriate, use the SNDRV_CTL_NAME_IEC958 instead of a literal
string.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
HDA Codec driver
- Fixed the reordering of surround channels.
Originally reported by Nicolas GRAZIANO <nicolas.graziano@wanadoo.fr>.
- Show the selected ssid when debug option is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
- Correct some index variable inversion in patch_cmedia.c
Signed-off-by: Nicolas Graziano <nicolas.graziano@wanadoo.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Adds support for detecting hp insertion/removal and enable/disable of
lineouts based on unsolicited events.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Intel driver
Patch enables unsolicited responses on the HDA controller. Without
the UREN bit set, the controller will not place unsolicited responses
in a RIRB.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,HDA Codec driver
- Added a new '6stack' model for ALC880.
- Fixed the typo in 6stack-digout model name.
- Added description for missing models in ALSA-Configuration.txt.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Adds resume support to the SigmaTel HDA patch. Please apply.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch creates a new kstrdup library function and changes the "local"
implementations in several places to use this function.
Most of the changes come from the sound and net subsystems. The sound part
had already been acknowledged by Takashi Iwai and the net part by David S.
Miller.
I left UML alone for now because I would need more time to read the code
carefully before making changes there.
Signed-off-by: Paulo Marques <pmarques@grupopie.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
HDA Codec driver
Adds SPDIF in/out support to the SigmaTel HDA codecs. Now builds
the input mux control element names from the defcfg regs.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,HDA Codec driver,HDA generic driver,HDA Intel driver
- Fix some invalid configurations, typos in the last patch
- Make init_verbs chainable, so that different configs can share the same
init_verbs
- Reorder and clean up the source codes in patch_realtek.c
- Add the pin default configuration parser, used commonly in cmedia
and realtek patch codes.
- Add 'auto' model to ALC880 for auto-configuration from BIOS
Use this model as default, and 3-stack as fallback
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver,HDA Intel driver
Merged the work of pshou <pshou@realtek.com.tw> for the support of
more models with ALC codecs: ALC880 ASUS, Uniwill, FSC1734, generic 6-stack,
and ALC260 HP. Tests with the real hardwares are appreciated.
The codec patch is cleaned up: The preset configuration of codecs are
stored in the table and copied to the spec instance.
Added/fixed comments.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Allow sub_device=0 in board config check. This means that every device
with the given sub vendor ID will match.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Clean up and fix ALC-codec support code.
The last addition of bound volume is fixed now to handle correctly
the bound 'mute switches'. The analog loopback should work better.
The init verbs are fixed together with this change.
The numbers are replaced with macros for better readability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Feed front signals to all surround channels if no data is given
for surround channels.
It seems that CLFE works as expected (only center outputs) even if
connected from the front line - at least on my test system.
If this change causes problems on other system (e.g. only the left
channel is transferred to the center channel), please let me know...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Fixed the handling of amp cache in hda-codec driver.
The confliction of cache values with different indices should be fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Fixed the capture on some ALC880 devices.
The node 0x07 is sometimes invalid as an ADC. Also, the intialization
of ADC nodes are fixed on some models.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Suppressing the error message regarding no AFG.
This is often harmless (e.g. probing a modem codec).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CA0106 driver,HDA Codec driver
This patch makes needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,HDA Intel driver
Added the support of VIA VT8251/VT8237A HD-Audio controllers.
They are (almost) compatible with Intel ICH6/7.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,HDA Intel driver
This patch changes the Intel HD Audio device driver to include
the support of HD Audio device embedded in ATI south bridge
IXP450. Because the design of ATI chipset follows intel HD Audio
specification 1.0, the programming method is the same as that
of intel HD Audio device exception one minor change which requires
to enable snoop for DMA transport. There are 3 changes that have been
made to hda_intel.c file.
1. Added device ID for ATI HD Audio device;
2. Increase maximum CODEC supported to 4;
3. Enable snoop during the driver initialization.
Signed-off-by: Frederick Li <fli@ati.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Added 'test' model for testing/debugging the devices with ALC880 codec.
This model is built only when CONFIG_SND_DEBUG is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,HDA Intel driver
Added position_fix module option to HDA-intel driver for fixing up
the DMA position (possibly hardware-) bugs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Fix and cleanup of CM9880 automatic PIN configuration.
snd_hda_codec_setup_stream() doesn't do anything when NID is 0.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA generic driver,HDA Codec driver
Add initial SigmaTel codec support for 9200 and 922x. Note that
this hda patch relies on the configuration default registers to
be set correctly (normally by BIOS/firmware) in order for it to
set up pin widgets properly. There's a test switch in the patch
so it will work with the SigmaTel reference boards that are usually
plugged into a system that doesn't set the configuration default
registers. It supports 2 channel analog out and line/mic in. I
plan to add >2 channel support and spdif support shortly.
Please apply.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver,HDA generic driver
Fix some vref defines so they are valid for the different bits in
the pin cap and pin control registers. Please apply.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Patch by C.L. Tien <cltien@cmedia.com.tw>:
The patch makes cm9880 to choose multi-channel jacks automatically.
1. I found the current code has basic_init, which already includes
necessary controls for 6-stack initialization, so I don't need
another model.
2. I add a new model 'auto' to let the driver find a. if there are
option real panel/front panel, b. the jacks to be used for multichannel.
Because the jack color are based on MS's channel sequence, so the 'auto'
model will pick the same jacks for multichannel MS uses. I did this to
hope to minimize users questions. These code can also be applied to other
codecs but I don't have any to test.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
The patch_cm9880.c can't play side/C/B channels from front panel jacks.
I fixed it by adding select pin.
Signed-off-by: ChenLi Tien <cltien@cmedia.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA generic driver
During debugging for cm9880 multi-channel playback, I added the * after
the currently selected widget, mixer widget doesn't need this but other
3 widget types need it.
Signed-off-by: ChenLi Tien <cltien@cmedia.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds the Intel ESB2 HD Audio DID to the hda_intel.c audio driver.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
