Manifest is fetched with control protocol now and so we don't need space
for it in hotplug data.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Control protocol is ready to be used for fetching manifest. Lets do it.
This changes few things:
- Creates/initializes bundle/connection for control protocol initially
and skips doing the same later.
- Manifest is parsed at link-up now, instead of hotplug which was the
case earlier. This is because we need device_id (provided during
link-up) for registering bundle.
- Manifest is fetched using control protocol.
So the sequence of events is:
Event Previously Now
----- ---------- ---
Interface Hotplug create intf create intf
parse mfst
Interface Link Up init bundles create control conn
get mfst size
get mfst
parse mfst
init bundles
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add control protocol driver that is responsible for handling operations
on control CPort. The AP also needs to support incoming requests on its
control port. Features not implemented yet are marked as TODO for now.
NOTE: This also fixes cport-bundle-id to 0 and cport-id to 2 for control
protocol.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
A connection and a bundle will be created for interfaces at the very
beginning for control protocol's functioning. And so the list of bundles
and connections for a interface will be non-empty by the time manifest
is parsed.
Currently we are firing a WARN when these lists are found to be
non-empty. Lets fix that to contain single bundle and connection for
control protocol.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Extend sdio implementation, as it for now it was basically stubs.
This implementation is compile tested only since there is no fw or
simulation support yet.
Next step is to add sdio support to gbsim and test it with success
using the mmc_test facility.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add MMC to the list of options that shall be enable.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Greg reported sparse picked up the following warning:
/home/gregkh/ara/greybus/uart.c:105:34: warning: cast to restricted __le16
This is due to the control variable in gb_uart_serial_state_request which
needs to be declared __le16 not __u16.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reported-by: Greg Kroah-Hartman <gregkh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
ES2 give us more endpoints. Use them to map one cport to two endpoints
(in and out). Because there is more cports than endpoints, we still
need to mux other cports traffic on 2 endpoints.
Firmware currently assumes these endpoints are 2 and 3.
By default, all cports are muxed.
To map one cport to 2 endpoints, use map_cport_to_ep().
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
ES2 support 16 endpoints. Update es2.c to allocate endpoints, urbs
and buffers for these new endpoints.
Currently, they are not yet used and es2.c is working in legacy mode
(only original endpoints are used).
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Instead of keep cport buffers, urbs and endpoints in es1_ap_dev,
move them in two dedicated struct (es1_cport_in and es1_cport_out),
in order to ease the migration to es2 (increase the number of endpoint).
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
We now limit the maximum value for both host and module CPort ids,
and we know they can always be represented in a single byte.
Make use of this by using only one of the two pad bytes for encoding
the CPort id in a message header.
(Note that we have never used a CPort higher than 255. Encoding
such a small CPort id in little endian 2-byte format has the same
result as what is done here.)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
For ES1 and ES2, we use pad bytes in an operation message header to
encode the CPort ID used for transferring the message. The pad
bytes should otherwise be zero, and we ensure this as the message
is passed to or from the upper layer.
If host-side CPort ID 0 is used, we have no way of knowing whether
the CPort field has been "packed" into the header.
To allow detection of this, reserve host CPort id 0. Update
cport_id_valid() to treat 0 as invalid.
(CPort ID 0 is reserved by one of the UniPro standards. We'll
assume for now that we never use it for Greybus.)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
We limit the number of host-side CPorts to a fixed maximum (which
is less than the 4096 that UniPro allows). This patch imposes a
similar limit on the CPort IDs defined by modules (signaling an
error if one too large is found in a manifest).
It seems reasonable to use the same value for both limits. Change
the name of the constant that defines the host limit and use it for
both. Update cport_id_valid() to enforce the maximum.
(Ultimately we should impose a limit like this; this change is being
made in preparation for supporting multiple connections over a
single CPort.)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
For the ES1 and ES2 host interfaces we encode the CPort ID over
which the message should be sent within the message itself. The
CPort ID is recorded in unused pad bytes found in the operation
message header in order to avoid introducing misaligned messages.
This patch defines some helper routines to abstract this activity.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Define a public predicate that defines whether a CPort ID is valid.
Use it in the message_send() routine, and make the message reported
more accurately reflect the error. Also use it to check whether the
CPort ID in a received message is valid; if it is not, just drop the
message.
Get rid of local variable "buffer" in message_send(); it adds no
value.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Currently, if an error occurs creating a bundle, we simply
return an error without cleaning up any of the bundles that
had already been successfully set up.
Add code to destroy bundles that have been created in the event
an error occurs. Add a check to ensure the interface's list of
bundles was empty before parsing for bundles begins.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Currently gb_bundle_destroy() takes an interface as an argument,
and really doesn't do what a function by that name should do.
What it now does is delete all bundles associated with a given
interface. What it should do is destroy a single bundle.
Move the looping logic out of gb_bundle_destroy() and into its
caller, gb_interface_destroy(). Pass each bundle in an interface to
gb_bundle_destroy(), which will do what's required to destroy a
single bundle (including removing it from its interface's bundle
list under protection of the lock).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Rearrange gb_bundle_find() so it follows the pattern used by
gb_connection_find().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Currently, if an error occurs creating a connection, we simply
return an error without cleaning up any of the connections that
had already been successfully set up.
Add code to destroy connections that have been created in the event
an error occurs. Add a check to ensure the bundle's list of
connections was empty before parsing for CPorts begins.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
I did this recently for the endo id allocation code.
It's clearer now that the allocation of a CPort ID to use for
the AP side of a connection is not very complicated, and it
happens in a pretty controlled environment. The functions that
abstract getting and releasing those ids don't really add that
much value.
This patch removes gb_connection_hd_cport_id_alloc() and
gb_connection_hd_cport_id_free(), and just open-codes their
activity in the few places they are called.
It is obvious now that the CPort ID allocation isn't done in
atomic context, so we can change the ida_simple_get() call to
use GFP_KERNEL.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Although a connection records its protocol id when it gets
created, its protocol handler doesn't actually get assigned
until gb_connection_bind_protocol() is called.
In gb_connection_create() there are some error paths in
which a reference to the connection's protocol is released
before the protocol handler has been associated with the
connection.
Get rid of those calls.
As a result, we will never pass a null protocol pointer to
gb_protocol_put(). Add a precautionary warning in that
function in the event that ever occurs.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
When an error occurs in the device_add() call for a connection, the
device reference is dropped as required. Because that's the device's
only reference, that will also lead to gb_connection_release() being
called, which frees the connection structure.
Right now we're then making an extra request to free the connection,
which is wrong. Fix that.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
There is lack of unregister and free the tty driver.
This patch fixes it.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
__init does not belong in a .h file, as it does not do anything there,
so remove all instances of it.
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
WARNING: /home/viresh/work/repos/ara/greybus/greybus.o(.init.text+0xb8):
Section mismatch in reference from the function init_module() to the
function .exit.text:gb_endo_exit()
The function __init init_module() references
a function __exit gb_endo_exit().
Fix it by removing __exit from endo_exit().
Fixes: cf64356c5151 ("endo: define endo_init() and endo_exit()")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Check at connection creation time for an attempt to create a
connection with an interface CPort ID that's the same as one that's
already been created.
Define a new helper function to look for such a duplicate. The
check for a duplicate is only performed at initialization time,
and CPorts are initialized serially for each bundle, so there's
no need to acquire the list lock for this search.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Check at bundle creation time to ensure we're not creating a bundle
with an id that's the same as one that's already been created.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Rework the the code that parses the manifest for bundles so it only
touches each manifest descriptor once. (Previously the list was
scanned from the beginning repeatedly until all bundles were found.)
Shorten the name of the descriptor variable, to avoid line wrap.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Rework the the code that parses the manifest for CPorts associated
with a bundle so it only touches each manifest descriptor once.
(Previously the list was scanned from the beginning repeatedly
until all bundle CPorts were found.) Shorten the name of the
descriptor variable, to avoid line wrap.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
An initialized bundle structure contains a pointer to its
interface. Because of this there's no need to provide
the interface pointer to gb_manifest_parse_cports(). This
also precludes the possibility of passing a bad interface
pointer.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This patch incorporates some very small cleanups to "manifest.c":
- Rearrange code a bit in gb_manifest_parse() that ensures a
manifest is big enough to hold a header. If the manifest is
exactly the size of a header, the error reported will now be
"...must have 1 interface..." rather than "short manifest".
- Fix the function comment for gb_manifest_parse_cports().
- Use "an interface," not "a interface," and don't capitalize.
- Delete some braces when getting interface product string.
- A few other minor changes to comments and white space.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Recently code was added (back) to assign a unique id to each
endo, so satisfy uniqueness requirements of the Linux device
subsystem. An ID allocator is used to manage the space of IDs.
Now that we have gb_endo_init(), we can initialize the map there,
and fully hide the ID map within "endo.c".
The original functions gb_endo_id_alloc() and gb_endo_id_free()
provided a nice abstract interface, but the direct ID allocation
calls are quite simple, so just call them directly.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Define init and exit functions to do one-time setup and teardown
of endo-related functionality. Currently they're place holders;
the next patch will populate them.
Note that we now call gb_operation_exit() from gb_init(), so
we can no longer mark that function with __exit.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The top-level functions gb_init() and gb_exit() are tagged with
__init and __exit, respectively. These functions call a few
other functions that are similarly used only at initialization
and termination time. So mark those functions accordingly.
Note that, because gb_ap_exit() and gb_debugfs_cleanup()
are called by gb_init() in error paths, these functions
cannot be declared with the __exit attribute.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
There's no need to include anything other than "greybus.h" in
"connection.c". Same thing in "core.c" and "manifest.c" and
"svc.c". Some files need headers included, but most come along
with "greybus.h".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The sample count placed in Greybus I2S audio messages should be
reset every time a new audio stream is set up. However, the
current code does not do the reset so make it so it does.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The firmware is having a hard time with 4k buffers and memory
allocation, so decrease the size on the host side to 2k. Also move away
from using PAGE_SIZE to denote 4k as that's not the case on all
architectures, and someone, someday, might get a rude surprise.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The unregister_chrdev_region() does twice here.
The chrdev region was unregistered
inside tty_unregister_driver().
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
There is a sparse warning. The endo id map is also
used in endo.c. Should define in endo.h
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Normally, its a good practice to free resources in the reverse order in
which they are allocated, so that all the dependencies can be sorted out
properly.
This is true while creating/destroying devices as well. For example
consider this scenario (I faced a crash with control protocol due to
this). For a new module, we will first create a bundle+connection for
the control cport and then create other bundles/connections after
parsing manifest.
And while destroying interface on module hot unplug, we are removing the
devices in the order they are added. And so the bundle/connection for
the control cport are destroyed first. But, control cport was still
required while destroying other bundles/connections.
To solve this problem, lets destroy the resources in the reverse order
in which they are added.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Provide a little more information in two pr_err() calls.
Also enclose a reported condition in parentheses, to match
the style used everywhere else in the file.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Rename greybus_deregister() to be greybus_deregister_driver(), so
its name mirrors the greybus_register_driver() function it matches.
Define greybus_deregister() to be a trivial macro.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
In gb_uart_request_recv(), the receive data size is in little-endian
format. Do the proper byte swapping of that value before using it.
Found by "make check".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Give gb_connection_hd_find() static scope; it's never used
outside "connection.c".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The SVC protocol driver should have been defined as a basic
Greybus protocol driver, not a GP Bridge protocol driver.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Prefix module-id with endo-id to uniquely identify it for the entire
kernel.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Currently we name the endo device as "endo". And it shows up with the
same name in sysfs directory: /sys/bus/greybus/devices/.
But each device in kernel should be represented by a unique id in
kernel, and "endo" isn't unique.
Lets generate unique ids for endo devices. The ida mechanism for
allocating ids may be overkill but it works.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This isn't unique just for the bundle but the complete interface. Its
wrong to call it bundle_cport_id. Lets name it intf_cport_id to make
things clear.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
'buffer' isn't used in this function, remove it.
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Use defines for the data format command.
Tidy up naming of gb_tty variables.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
gb_uart_request_recv job in life is to process unsolicited greybus
mesages from the UART.
Hook the incoming UART data and pass to the TTY layer.
Line-state changes still TBD.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Make kmalloc for the send buffer a one time alloc based on the MTU for
a given greybus link.
The write_room for an gb_operation_sync then will be the size of the
buffer we use for a single operation.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
gb_operation_sync returns 0 on success but the calling function
expects the number of bytes written on success or a negative errno
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
For each new UART connection we need to do a tty_port_init else
we'll crash when trying to access the tty mutex later on.
Base the TTY major/minor numbers on non-zero values.
Supply an empty operations structure for the newly regitered port.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Arbitrary number 255 is both not aligned and probably too big.
Move the UART count down to 16 which is still large but, more realistic.
8 may be too few for future testing setups, 16 should accomodate any.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Update tabs and naming of structures to match the naming used in the greybus
specification more closely.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
gbsim depends on the structures and defines in greybus_protocols.h
generally in order to simulate firmware. Move UART defines into this
header to facilitate.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
If alloc minor is error, gb_tty should free.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Because of the missing '\n', this is how the output of reading endo
sysfs files looks:
root# cat /sys/bus/greybus/devices/endo/id
0x4755root#
Fix it by including \n to the end of the printed string.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add Greybus GPIO IRQ-type defines rather than rely on the current
Linux implementation.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
With the Endo "id" attribute in place, there's no need to encode
the ID of an Endo in its sysfs path. So get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This commit:
7e761e2 endo: rework some attributes
added a new "endo_id" attribute, located under a new "Endo"
directory in sysfs. The resulting path looks like:
Documentation/sysfs/endo-TYPE/Endo/endo_id
There's no need to have a separate "Endo" subdirectory to contain
Endo-specific attributes.
That commit also added "svc_" to some other paths related to the
SVC, like:
Documentation/sysfs/endo-TYPE/SVC/svc_version
The additional "svc_" is redundant.
This patch retouches those paths a bit, mainly to remove some
redundancy. It also makes the pathname components all lower case.
As a result, the above two paths now look like:
Documentation/sysfs/endo-TYPE/id
Documentation/sysfs/endo-TYPE/svc/version
All other Endo sysfs files are updated similarly.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Impose a few editorial conventions on the Greybus-related sysfs
files under "Documentation".
- Capitalize "Endo" (except in path names)
- Capitalize "ID" (except in path names)
- Use "..." to indicate unspecified path components (because
".." means something else).
- Add the "0x" prior to the "XXXX" representing the Endo ID.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Update the files documenting Greybus-related sysfs files under
Documentation/ to reflect the addition of the two recently-added
Endo attributes.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This is not a kernel module. It should not use
the module license macro.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
I neglected to update the "#ifndef/#define" when I renamed
"greybus_protocols.h". Fix that.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Update the remaining operation types now that the ack operation is gone
to avoid leaving a hole in the type definitions.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change to gb_gpbridge_protocol_driver for
making the consitent with other drivers.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
data of hotplug request should exchange to native
CPU format before assignment.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The current interrupt implementation uses the simple irq-flow handler,
which means that the interrupt subsystem makes no irq-chip callbacks
when handling an interrupt. Specifically, no end-of-interrupt message is
sent when the threaded handler has run. This means that we may currently
re-enable an interrupt before it has been serviced (i.e. the irq-event
operation may complete before the threaded handler has run).
The simple flow handler also silently drops a second interrupt arriving
while a handler is running. This means that we may lose a second edge
interrupt with the current firmware.
Switch to a new one-shot interrupt protocol, where the primary handler
(firmware) always masks and acks an interrupt before sending an event to
the AP. The AP is responsible for unmasking the interrupt when it has
been handled. By having the firmware ack an edge interrupt before
sending the event, a second edge interrupt will no longer get lost.
This one-shot protocol can be implemented in the kernel by using the
level irq-flow handler, one-shot interrupts with threaded handlers and
bus-lock synchronisation for slow buses. Note that the same flow handler
is used for both edge and level interrupts.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The irq-chip callbacks are made in atomic context where we must not do
any synchronous greybus operations.
Fix the current gpio-interrupt implementation by using the bus-lock
functionality provided by the irq subsystem.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Rename irq mask and unmask functions to match the callback names.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Use irq_find_mapping directly rather than go through the legacy gpio
interface.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Use generic_handle_irq_desc rather than call a hardcoded irq-flow
handler directly.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Remove unused irq-ack operation, which has never been called and does
not make sense for message-signalled interrupts over slow buses.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Fix debugfs output by removing the unimplemented, custom dbg_show
callback. The default implementation is perfectly sufficient.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add support for incoming, unidirectional operations where the sender of
a request does not care about a response.
Unidirectional operations have an operation id of 0.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This patch adds support for the Greybus SVC protocol. We may want
to rearrange protocol numbers at some point, since this is a pretty
fundamental protocol.
Note: It has only been compile tested; no SVC CPorts have yet been
defined, so this code is not yet exercised.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The Greybus audio source files included no copyright statements.
Add them.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Currently, the data structure representing an Endo is set up at the
time a host device gets created. This is too early.
Once the control infrastructure is in place, there's no sense in
setting up the Endo utnil after we have heard from the SVC via a
probe operation on our control CPort. And even then, there's
no real point until we've successfully authenticated with the SVC,
which will be indicated by the arrival of the Control protocol
"connected" operation request notifying us that our SVC CPort
is operational.
In addition to this logical argument, we also can't actually
receive any messages on the Control CPort until the host device
is set up and ready to receive messages. At the point we're
currently setting up the Endo data structure, that has not yet
been done.
Define a new exported function greybus_endo_setup(), which will
be used (for now) as the entry point for setting up the Endo
data structure. Arrange to call it in the host USB driver
probe method, *after* we are set up for handling messages.
Note: Once the control protocol has been implemented, this function
may no longer need to be exported.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The AP resides in a particular position on an Endo, which is
identified by an interface ID. (For now we'll assume the AP uses
just one interface.) Record the this AP interface ID when creating
an Endo. Add a sysfs attribute to display it as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The SVC is not the same as the Endo. There are some attributes
(such as the Endo ID) that are independent of attributes of
the SVC (like its version).
The current "Endo attributes" are really SVC attributes.
Rename a few functions and variables to reflect that.
Add a new attribute group for Endo-specific attributes, and
populate it with the Endo ID.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The maximum interface id on an Endo is the result of a non-trivial
calculation. It'll be needed for an upcoming patch, so create a
macro to compute it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The file "gpbridge.h" is now used as a single place to define
all protocol message structures. These protocols are not
necessarily related to the GP bridge, so the name of the
file is misleading.
Rename it "greybus_protocols.h".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Avoid the need for all the source files to include "gpbridge.h"
by just having "greybus.h" include it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Return a pointer-coded error from greybus_create_hd() rather
than NULL in the event an error occurs.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Return a pointer-coded error from gb_endo_create() rather than just
a null pointer in the event an error occurs.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
We are going to want to defer creating the endo until we receive a
probe operation from the SVC, which will supply the endo id. Change
gb_endo_create() so it passes the endo_id value as an argument.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change the name of "struct gb_svc" to be "struct svc_info". The
structure now contains only the SVC's serial number and version (and
are place holders anyway). We will be defining a structure that
represents the SVC for the SVC protocol connection, and I want to
take back that name.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
A recent commit moved the I2S samples per message operation
to the PCM's 'hw_params' callback. However, the 'hw_params'
callback is called numerous times while the samples per
message need only be done once (or seldom). Eliminate the
unnecessary samples per message operations by doing it only
once at Greybus protocol init time.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Currently, the audio driver unconditionally sets the I2S
configuration to have a sample rate of 48KHz, two channels,
16 bits per channel, in little endian order. Make this
more flexible by setting the I2S configuration according to
the arguments passed to the PCM 'hw_params' callback.
To accomplish this, query for the supported I2S configurations
at Greybus protocol init time and save them in the 'snd_dev'
structure. When the 'hw_params' callback is called, compare its
arguments to the table of supported configurations. If there is
a match, set the I2S connection accordingly.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Currently, the audio driver activates & deactivates a predefined
CPort ID but that can vary depending on the manifest data of the
module. Instead, use the TX connection's Bundle CPort ID which
contains the correct CPort ID.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Currently, the I2S TX CPort is configured and activated during
the Greybus audio initialization. Unfortunately, this prevents
the audio driver from ever changing the I2S configuration.
To allow the I2S configuration to change according to ASOC requests,
move the CPort activation & deactivation to the audio-pcm workqueue.
Now, when audio is running but the CPort is not active, it will be
activated. When audio is not running and the CPort is active, it
will be deactivated.
This has the side-effect of sending the first piece of audio data
immediately after activating the CPort which is really how it should
work anyway.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Remove comment about adding start delay since it will
be done when support for A/V synchronization is added.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add the I2C device node for the rt5647 codec.
Eventually, this will be done automatically somewhere
else but for now its done in the audio driver.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The asoc_simple_dai structure does not contain the 'fmt'
member in Linux kernel version v4.1 and later so only
build code that uses it when the kernel version is earlier
than v4.1.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Set the various DAI formats so the bridge on the module
is the master of all clocks and the codec is the slave.
The only DAI protocol currently supported is I2S.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Instead of using the fixed suffix, '6-001b', in the
codec name, generate it from the I2S adapter number
and I2C address of the codec.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The greybus code requires that an operation's response buffer be
the exact size of the response; however, the size of the response to
the GB_I2S_MGMT_TYPE_GET_SUPPORTED_CONFIGURATIONS operation is unknown.
To fix this, an extension to the I2S specification is required.
In the meantime, set the number of configurations returned to 20
because that is how many configurations will be returned (using
"insider knowledge" of the firmware).
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The rt5647 codec on speaker and mediabar modules require that
the following clock edge settings:
ll_wclk_change_edge GB_I2S_MGMT_EDGE_FALLING
ll_wclk_tx_edge GB_I2S_MGMT_EDGE_RISING
ll_wclk_rx_edge GB_I2S_MGMT_EDGE_FALLING
(Those are the setting that work, at least). So make the Greybus
audio driver configure the GPBridge with those settings.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Fix section mismatches introduced by b27227ce93c0 ("greybus: Use
gb_gpbridge_protocol_init()"), which added __exit annotation to
gpbridge-protocol exit functions that are called in the error path of
gpbridge_init, which lives in the init section.
This triggered the following modpost warning:
WARNING: modpost: Found 8 section mismatch(es).
Fixes: 16b33d100bff ("protocol: Add gb_gpbridge_protocol_driver()")
Fixes: b27227ce93c0 ("greybus: Use gb_gpbridge_protocol_init()")
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add helper to retrieve the maximum payload size for operations on a
specific connection.
Note that the helper is not inlined due to how the header files are
currently organised, but it is not expected to be called after a
connection has been initialised either.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Make sure we never end up with a host device with maximum buffer size
smaller than the shortest Greybus message.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Increase the maximum allowed buffer size to the full 16-bit range
supported by the protocol.
Note that host devices will generally use smaller buffers than the
maximum.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Host devices impose buffer-size constraints on Greybus core which are
taken into account when allocating messages.
Make sure to verify these constraints when the host device is allocated,
rather than when the first message is allocated.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Remove a couple of unused function prototypes from the greybus header
file.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Remove unnecessary greybus.h include from header files.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
There are many gpbridge protocol drivers that need gb_protocol_driver()
without the module_init/exit() lines. Lets create one for them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
That's what followed for .h, etc.. Rename for better consistency.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This is what coding guidelines say. Lets do it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Routines should be named this way: gb_<object>_<operation>. Fix all
routines that don't match this.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Routines should be named this way: gb_<object>_<operation>. Fix all
routines that don't match this.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Routines should be named this way: gb_<object>_<operation>. Fix all
routines that don't match this.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Routines should be named this way: gb_<object>_<operation>. Fix all
routines that don't match this.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
In order to facilitate re-use of spi structures, split them out of
independent files and add them into a shared gpbridge.h
This will be a prereq to sharing these headers w/ gbsim.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Spaces were present in place of tab. Fix that.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This is what I get over mainline:
greybus/raw.c: In function 'gb_raw_send':
greybus/raw.c:153:2: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
if (copy_from_user(&request->data[0], data, len)) {
^
greybus/raw.c: In function 'raw_read':
greybus/raw.c:305:2: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
if (copy_to_user(buf, &raw_data->data[0], raw_data->len)) {
^
Fix this by including uaccess.h.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This adds a driver that implements the greybus Raw protocol as
specified.
It preserves the message boundries by only allowing a read to receive
a "full" message, and any write() call also is passed in a single
greybus request.
Totally untested, given that we have no raw firmware or gbsim code yet.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
ida_simple_* has a built-in spinlock, no need to grab another lock when
accessing it.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
All we need is a simple ida, so use that interface instead of the more
"complex" idr one. Bonus is we don't need to fix the locking issue I
forgot about when using an idr, as ida has one built-in.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
It should remove the object from sysfs when loopback
connection init error.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add checks for options that shall be enabled in the kernel config
and for options that shall be disable.
To add options to list append them to CONFIG_OPTIONS_ENABLE or
CONFIG_OPTIONS_DISABLE respectively.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
There's no reason we can't support loopback pings or transfers
initiated by the module. Allow it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add some symbols to indicate what kind of "function" the
loopback thread is supposed to be performing--the type of
traffic it generates over its connection.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Use a symbolic constant to define the maximum time (number of
milliseconds) to delay between initiated operations.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Fix a comment that incorrectly says the delay between messages is
limited to 1024 msec; it actually must be <= 1000 msec.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
If an error occurs starting up the loopback thread, the error code
is not extracted properly. Fix that.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
In gb_loopback_check_attr(), the value of gb->type is checked for
validity. The only valid values are 0, 1, and 2. But the check
allows the value 3. Fix that.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
sparse is rightfully complaining about a lack of converting when
accessing or assigning to little endian fields. Fix them all up to work
properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
This makes some functions and structures static, as warned by sparse, as
they don't need to be global.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
remane protocol define from GREYBUS_PROTOCOL_LED to GREYBUS_PROTOCOL_LIGHTS to
be coherent with the specification.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
We already have code to parse Endo ID, lets use it to create modules at
run time instead of creating them from a static array.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Endo is described by a 16 bit value. Which represents the properties of
modules, interface and ribs on front and back of endo.
This 16 bit value can be used to find all possible pairs of modules and
interfaces and creating modules based on that.
This patch provides helpers to parse 16 bit Endo ID.
(Based on original code written by Alex Elder.)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
In commit 1efb53a220 ("ASoC: simple-card: Remove support for setting
differing DAI formats"), the .fmt field was removed from struct
asoc_simple_dai. Fix this build breakage by not trying to set it.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Acked-by: John Stultz <john.stultz@linaro.org>
sizeof wants %zu when on a 64bit build, so change the dev_err() call to
remove a build warning in the audio.c file.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Introduce INSTALL_MOD_PATH to allow for building and installing of the
greybus modules from a different location.
This lets you build the greybus modules on a PC and then install the
modules to an SD card in the appropriate location relative to the SD such
as /media/sdcard/lib/modules/version and subsequent running of depmod in
the same location. If INSTALL_MOD_PATH isn't specified the default
behaviour of installing and depmoding to /lib/modules/version is
maintained.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
So here's the current greybus audio driver, which I
wanted to send out for more serious review and
consideration for merging.
I've tried to integrate much of the feedback from the
last round and most of the hotplug issues that I've found
have been resolved. I've tested this via gbsim, and the
Android ARA HAL layer seems to work with it.
Mark has also successfully played audio with this driver,
adding a few hacks to get the codec's i2c connection to
probe.
Current issues:
* Hotplug problem - When gbsim is killed, or the module
removed, the greybus driver gets stuck since the android
mediaserver process is holding the audio device open.
Killing the mediaserver allows things to clean up and
allows greybus to accept new gbsim connections. I have
a workaround patch to the soc-core.c logic which converts
the snd_card_free() call to snd_card_free_when_closed()
which allows the greybus connection cleanup to finish.
Remaining todos:
* Probably need to break apart the mgmt_setup function
to integrate better with the constraint logic. I took
a really basic stab at this, but more is probably
needed.
* Figure out how to properly find and tie in the
codec's I2C bus-id to the driver.
This code requires that the kernel support the following
config options, which I've enabled in a separate kernel
patch:
CONFIG_SND_SIMPLE_CARD
CONFIG_SND_SOC_SPDIF
CONFIG_SND_SOC_RT5645
I really can't calim to be the sole author of this, since
many many fixes and tweaks that have been folded in have
come from Mark Greer. His analsysis and debugging is really
what has made this dummy-framework driver evolve into an
actual audio driver. So much credit and thanks to Mark!
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
All protocols use the same value to distinguish between request and
response message types. This is a requirement.
Use GB_MESSAGE_TYPE_RESPONSE rather than GB_OPERATION_TYPE_RESPONSE
for the name of the flag used to distiguish between request and
response messages.
Get rid of the redundant response flag definitions that are
associated with specific protocols.
Describe the symbolic values as "operation types" rather than
"message types" where they are defined. The message type for a
request is the same as the operation type; the message type for a
response is the operation type OR'd with GB_MESSAGE_TYPE_RESPONSE.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Conditionally define a new symbol DRIVER_OWNS_PSY_STRUCT, which is
set in "kernel_ver.h" based on on the kernel version. Use it to
distinguish code used for kernels that differ in whether a power
supply structure is owned by the driver, or by the power supply
core.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
When a battery connection is initialized, a gb_battery structure for
it is allocated in gb_battery_connection_init(). Currently that
function ends by calling init_and_register(); in the event an error
occurs, init_and_register() is responsible for freeing the allocated
gb_battery structure.
Make the code a bit better balanced by having the function that
allocates the structure be responsible for freeing it in case of
error.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Both ES1 and ES2 drivers cannot be loaded due to a driver name conflict.
Give ES2 driver the correct name.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
No need to go past 80 characters for the define_get_version macro, so
fix up the indentation to not do so.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Remove the trailing ';' character from the gb_protocol_driver() macro as
it's not needed and is bad coding style.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
checkpatch reminds us that a blank line should go after a variable
definition, so fix it up here.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
You should always put a space after a ',', so do it for the
KERNEL_VERSION() macro as well. This makes checkpatch.pl happy also.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
When cutting and pasting some of the ATTR macros into kernel_ver.h, I
dropped the tabs. Fix this up and make checkpatch.pl happy.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
The 4.1-rc1 kernel changed the power supply apis such that the
structures are now owned by the power supply core, and not the
individual drivers. This broke the greybus battery driver, so update it
to support both the old and the new apis.
The API changes were such that I can't "hide" them in kernel_ver.h, but
rather the driver itself needs to have ugly #ifdefs in it. I tried to
keep it to a minimum, making a sub-function for initializing the power
supply device that is implemented differently for different kernel
versions.
When this is submitted upstream, or if we ever move our AP development
to 4.1 or greater, the support for older kernels can be removed.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Note that this also makes sure the id-field is naturally aligned in case
we ever were to remove the __packed attribute.
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Explicitly add pad-bytes to manifest descriptors to match their layout
in greybus specification.
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
We carry this information as part of bundle descriptor now and this can
be removed.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
It is not required anymore. Drop it.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
These should come from control protocol instead.
For now, initialize this statically with a FIXME to not forget it later.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The kernfs code guarantees we'll get a NUL-terminated buffer.
Use kstrdup() rather than kzalloc() + memcpy() in state_store()
making it slightly clearer what we're doing. This has the added
benefit of guaranteeing that the stored string has no NUL character
inside it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
A descriptor passed to AP can be bigger than what AP expects, if
manifest's minor version is higher with same major number as the AP. As
it can have some extra data in descriptor.
But, if AP and manifest versions are identical, or if the AP's minor
version is greater than the manifest version, we should at least warn
(if not fail).
Doing this would require some changes to record the manifest version
somewhere reachable by identify_descriptor().
For now, just warn if descriptor is bigger than expected.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
String descriptors are padded towards the end to align them to 4 byte
boundaries. Take that into account while calculating expected size.
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
These structures are already marked as __packed, as these are enclosed
within:
#pragma pack(push, 1)
#pragma pack(pop)
Lets mark them __packed explicitly.
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
There can be three Endo types: mini, medium and large. And that's what
Endo 'type' should refer to.
But we have named the 16 bit number that uniquely represents a valid
endo, as its type. 'id' seems to be a more suitable name to that instead
of 'type'. Lets rename it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
0x0555 isn't a valid endo id, use a real one.
0x4755 should be the Endo id for the (medium) Spiral 2 prototype. Lets
use that.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
These are all GPLv2-only kernel modules, so properly set the correct
MODULE_LICENSE string to make static checkers happy.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
A bundle has a state file, that is managed by the endo userspace
process. This file can be written to and any process that is polling on
the file will be woken up and can read the new value. It's a "cheap"
IPC for programs that are not allowed to do anything other than
read/write to kernel sysfs files.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The code uses 64-bit divisions, which should be avoided, and also
prevents the module from loading on 32-bit systems:
gb_loopback: Unknown symbol __aeabi_uldivmod (err 0)
Fix by using the kernel's 64-bit by 32-bit division implementation
do_div.
Compile tested only. I did not look very closely at the code itself.
Perhaps this could be worked around in some other way, but this silences
the linker warning and allows the module to be loaded.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
It's up to other files to define this if it's not present, not this
file.
Reported-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Replace #define<TAB> with #define<SPACE>.
Also move the #ifdef block to below the initial comment block, like
other .h files are.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
In order to facilitate re-use of the gpio, i2c, pwm and i2s
structures, split them out of independent files and add
them into a shared gpbridge.h
This will be a prereq to sharing these headers w/ gbsim.
Cc: Alex Elder <alex.elder@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@google.com>
CC: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This documents the module slot sysfs files "epm", "power_control", and
"present".
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
This documents the endo device, and the SVC specific files that are
present in the sysfs device tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
The kernel is now on the 4.XX numbering scheme, and it's going to be a
while before we merge this code, so pick a date sometime in the future
to be safe.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
This hooks up the endo, and modules, into the device tree. All modules
for a specific endo are created when the host device is initialized.
When an interface is registered, the correct module for it is found and
that module is used for the sysfs tree. When the interface is removed,
the reference on the module is dropped.
When the host device goes away, the whole endo and modules are removed
at once.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
This adds endo.c and endo.h and provides functions to create an endo and
the initial 0x0555 set of modules.
But, it doesn't hook this logic up into the running code yet, that comes
next.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
This adds the attributes power_control and present to a module. It also
removes the unneeded module_id attribute, as that comes from the name of
the module itself.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Drop the host-driver buffer headroom that was used to transfer the cport
id on ES1 and ES2.
Rather than transferring additional bytes on the wire and having to deal
with buffer-alignment issues (e.g. requiring the headroom to be a
multiple of 8 bytes) simply drop the headroom functionality.
Host drivers are expected set up their transfer descriptors separately
from the data buffers and any intermediate drivers (e.g. for Greybus
over USB) can (ab)use the operation message pad bytes for now.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Fix transfer-buffer alignment of es2 as well.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Fix transfer-buffer alignment of outgoing transfers which are currently
byte aligned.
Some USB host drivers cannot handle byte-aligned buffers and will
allocate temporary buffers, which the data is copied to or from on every
transfer. This affects for example musb (e.g. Beaglebone Black) and
ehci-tegra (e.g. Jetson).
Instead of transferring pad bytes on the wire, let's (ab)use the pad
bytes of the operation message header to transfer the cport id. This
gives us properly aligned buffers and more efficient transfers in both
directions.
By using both pad bytes, we can also remove the arbitrary limitation of
256 cports.
Note that the protocol between the host driver and the UniPro bridge is
not necessarily Greybus. As long as the firmware clears the pad bytes
before forwarding the data, and the host driver does the same before
passing received data up the stack, this should be considered "legal"
use.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add explicit pad bytes to the message header.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Make sure to allocate the message transfer-buffer separately from the
containing message structure to avoid data corruption on systems without
DMA-coherent caches.
The message structure contains state that is updated while the buffer
may be used for DMA, something which could lead to data corruption due
to cache-line sharing on some architectures.
Use the (renamed) message cache for the message structure itself and
allocate the buffer separately.
If the additional allocation is a concern, the message structures
could eventually be allocated as part of the operation structure.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Pass structured greybus messages rather than buffers to the host
drivers.
This will allow us to separate the transfer buffers from the message
structures.
Rename the related functions to reflect the new interface.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Move operation message-header to operation.h so that it can be used
by host drivers.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Remove unused and unnecessary buffer-alignment define that host driver
were supposed to use.
We can handle unaligned incoming buffers just fine by accessing the
operation-message header via a copy in the receive path, rather than
requiring host drivers to make sure the alignment is correct.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The buffer received from our current host driver is 1-byte aligned and
will therefore cause unaligned memory accesses if simply cast to an
operation-message header.
Fix this by making a properly aligned copy of the header in
gb_connection_recv_response before accessing its fields.
Note that this does not affect protocol drivers as the whole buffer is
copied when creating the corresponding request or response before being
forwarded.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Fix two bugs in es2 and do some minor clean up.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The maximum buffer size does not include the headroom, so subtract the
headroom size from the actual buffer size.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
A stack-allocated buffer is not generally DMA-able and must not be used
for USB control transfers.
Note that the memset and extra buffer byte were redundant as no more
than the bytes actually transferred was ever added to the fifo.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Alex suggested to name it class instead of class type.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
A Greybus driver will bind to a bundle, not an interface. Lets follow
this rule in code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
A module can have more than one interfaces and we get hotplug events or
manifests for interfaces, not modules. Details like version, vendor,
product id, etc. can be different for different interfaces within the
same module and so shall be fetched from interface descriptor instead of
module descriptor.
So what we have been doing for module descriptors until now must be done
for interface descriptors. There can only be one interface descriptor in
the manifest. Module descriptor isn't used anymore and probably most of
its fields can be removed now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
An interface can have 1 or more bundles. On link-up event, we must initialize
all the bundles associated with the interface.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
