While PCI card faces EEH errors, reset (usually hot reset) is
expected to recover from the EEH errors. After EEH core finishes
the reset, the driver callback (be_eeh_reset) is called and wait
the firmware to complete POST successfully. The original code would
return with error once detecting failure during POST stage. That
seems not enough.
The patch forces the driver (be_eeh_reset) to wait the firmware
completes POST until timeout, instead of returning error upon
detection POST failure immediately. Also, it would improve the
reliability of the EEH funtionality of the driver.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Acked-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should reset nf settings bond to the skb as ipip/ipgre do.
If not, the conntrack/nat info bond to the origin packet may continually
redirect the packet to vxlan interface causing a routing loop.
this is the scenario:
VETP VXLAN Gateway
/----\ /---------------\
| | | |
| vx+--+vx --NAT-> eth0+--> Internet
| | | |
\----/ \---------------/
when there are any packet coming from internet to the vetp, there will be lots
of garbage packets coming out the gateway's vxlan interface, but none actually
sent to the physical interface, because they are redirected back to the vxlan
interface in the postrouting chain of NAT rule, and dmesg complains:
Mar 1 21:52:53 debian kernel: [ 8802.997699] Dead loop on virtual device vxlan0, fix it urgently!
Mar 1 21:52:54 debian kernel: [ 8804.004907] Dead loop on virtual device vxlan0, fix it urgently!
Mar 1 21:52:55 debian kernel: [ 8805.012189] Dead loop on virtual device vxlan0, fix it urgently!
Mar 1 21:52:56 debian kernel: [ 8806.020593] Dead loop on virtual device vxlan0, fix it urgently!
the patch should fix the problem
Signed-off-by: Zang MingJie <zealot0630@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
===================
This series contains fixes to e1000e and igb.
The e1000e fix resolves an issue at 1000Mbps link speed, where one of the
MAC's internal clocks can be stopped for up to 4us when entering K1 (a
power mode of the MAC-PHY interconnect). If the MAC is waiting for
completion indications for 2 DMA write requests into Host memory
(e.g. descriptor writeback or Rx packet writing) and the
indications occur while the clock is stopped, both indications will be
missed by the MAC causing the MAC to wait for the completion indications
and be unable to generate further DMA write requests. This results in an
apparent hardware hang. The patch works-around the issue by disabling
the de-assertion of the clock request when 1000Mbps link is acquired (K1
must be disabled while doing this).
The igb fix to drop BUILD_BUG_ON check from igb_build_rx_buffer resolves
a build error on s390 devices. The igb driver was throwing a build error
due to the fact that a frame built using build_skb would be larger than 2K.
Since this is not likely to change at any point in the future we are better
off just dropping the check since we already had a check in
igb_set_rx_buffer_len that will just disable the usage of build_skb anyway.
The igb fix for i210 link setup changes the setup copper link function
to use a switch statement, so that the appropriate setup link function
is called for the given PHY types.
Lastly, the igb fix for a lockdep issue in igb_get_i2c_client resolves
the issue by re-factoring the initialization and usage of the i2c_client.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a few powerpc bits & fixes for rc1. A couple of str*cpy
fixes, some fixes in handling the FSCR register on Power8 (controls
the enabling of processor features), a 32-bit build fix and a couple
more nits."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Set DSCR bit in FSCR setup
powerpc: Add DSCR FSCR register bit definition
powerpc: Fix setting FSCR for HV=0 and on secondary CPUs
powerpc: Wireup the kcmp syscall to sys_ni
powerpc: Remove unused BITOP_LE_SWIZZLE macro
powerpc: Avoid link stack corruption in MMU on syscall entry path
drivers/tty/hvc: Use strlcpy instead of strncpy
powerpc/pseries/hvcserver: Fix strncpy buffer limit in location code
powerpc: Fix compile of sha1-powerpc-asm.S on 32-bit
into scatterlists. Jens has a check queued for this, so it shouldn't happen
again.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=OHfs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio hwrng fix from Rusty Russell:
"Nasty side-effect of vmalloc'ing modules: their static vars cannot be
put into scatterlists. Jens has a check queued for this, so it
shouldn't happen again.
We could fix this in virtio_rng, but it's actually far easier to just
do it in the core"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
hw_random: make buffer usable in scatterlist.
Pull networking fixes from David Miller:
"A moderately sized pile of fixes, some specifically for merge window
introduced regressions although others are for longer standing items
and have been queued up for -stable.
I'm kind of tired of all the RDS protocol bugs over the years, to be
honest, it's way out of proportion to the number of people who
actually use it.
1) Fix missing range initialization in netfilter IPSET, from Jozsef
Kadlecsik.
2) ieee80211_local->tim_lock needs to use BH disabling, from Johannes
Berg.
3) Fix DMA syncing in SFC driver, from Ben Hutchings.
4) Fix regression in BOND device MAC address setting, from Jiri
Pirko.
5) Missing usb_free_urb in ISDN Hisax driver, from Marina Makienko.
6) Fix UDP checksumming in bnx2x driver for 57710 and 57711 chips,
fix from Dmitry Kravkov.
7) Missing cfgspace_lock initialization in BCMA driver.
8) Validate parameter size for SCTP assoc stats getsockopt(), from
Guenter Roeck.
9) Fix SCTP association hangs, from Lee A Roberts.
10) Fix jumbo frame handling in r8169, from Francois Romieu.
11) Fix phy_device memory leak, from Petr Malat.
12) Omit trailing FCS from frames received in BGMAC driver, from Hauke
Mehrtens.
13) Missing socket refcount release in L2TP, from Guillaume Nault.
14) sctp_endpoint_init should respect passed in gfp_t, rather than use
GFP_KERNEL unconditionally. From Dan Carpenter.
15) Add AISX AX88179 USB driver, from Freddy Xin.
16) Remove MAINTAINERS entries for drivers deleted during the merge
window, from Cesar Eduardo Barros.
17) RDS protocol can try to allocate huge amounts of memory, check
that the user's request length makes sense, from Cong Wang.
18) SCTP should use the provided KMALLOC_MAX_SIZE instead of it's own,
bogus, definition. From Cong Wang.
19) Fix deadlocks in FEC driver by moving TX reclaim into NAPI poll,
from Frank Li. Also, fix a build error introduced in the merge
window.
20) Fix bogus purging of default routes in ipv6, from Lorenzo Colitti.
21) Don't double count RTT measurements when we leave the TCP receive
fast path, from Neal Cardwell."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tcp: fix double-counted receiver RTT when leaving receiver fast path
CAIF: fix sparse warning for caif_usb
rds: simplify a warning message
net: fec: fix build error in no MXC platform
net: ipv6: Don't purge default router if accept_ra=2
net: fec: put tx to napi poll function to fix dead lock
sctp: use KMALLOC_MAX_SIZE instead of its own MAX_KMALLOC_SIZE
rds: limit the size allocated by rds_message_alloc()
MAINTAINERS: remove eexpress
MAINTAINERS: remove drivers/net/wan/cycx*
MAINTAINERS: remove 3c505
caif_dev: fix sparse warnings for caif_flow_cb
ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver
sctp: use the passed in gfp flags instead GFP_KERNEL
ipv[4|6]: correct dropwatch false positive in local_deliver_finish
l2tp: Restore socket refcount when sendmsg succeeds
net/phy: micrel: Disable asymmetric pause for KSZ9021
bgmac: omit the fcs
phy: Fix phy_device_free memory leak
bnx2x: Fix KR2 work-around condition
...
This branch contains a few bug fixes that I missed the first time around
and updates to the gpio_desc series included in the first pull request.
This tag has been retagged to drop the 2 head commits because the one of
them caused a build failure.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rX0+
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull second round of GPIO changes from Grant Likely:
"This branch contains a few bug fixes that I missed the first time
around and updates to the gpio_desc series included in the first pull
request. This tag has been retagged to drop the 2 head commits
because the one of them caused a build failure."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio/gpio-ich: fix ichx_gpio_check_available() return what callers expect
gpiolib: move comment to right function
gpiolib: use const parameters when possible
gpiolib: check descriptors validity before use
mostly little bugfixes.
Only "feature" is a new RAID10 layout which slightly
improves the number of sets of devices that can concurrently
fail, without data loss.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIVAwUAUTPm+znsnt1WYoG5AQLLsw/+PMqr8roC4twgxTWV1NRbU8NtOcRi9Rj9
uvBS63uYAaLdi/D3UBKFYczmNCu9knuXbcp9SgFDxH7LlthQsWN/GYnif06pPo3w
9Agu5M8c062TJEG1vrnX6FhPO6pNgrWFr3h+CKkTiD3179i9DoQpP8LXQToeyMtI
YRMQf/zCkxYtDvWAP0iwsEWtw8cf+q9I/uGPhQ1L+DnZapXYdbtnqWBRz9q6mrDt
orcGrP41aZHvnOHUaTbwmaorCKkf/Ys4SMaGenrSFpnpQMypt7VgNuwHC59LxvJT
5eiFG/26zIsv7Wk0jv/TvFP5qzUPo0/PFkd5ug0ArvbVRiXS2cMJDwQvMdO1toxD
i5Bb+P9DptadvoWhOTgIpxnG77yRH45wJvyJOk+ZfS1/IO87nCRa3d0yiNOU5e2/
o0VdXPZRr72sdKKTK6kQuYfwCPb+Z2Pz6Q8BJdk6GxlmTXyP6sKhIgwUX86534fE
LrOxfK8qV+GetVu3X02RoX2CyJJRQHXyXmbHuSzXuo/JiOYtDigAydwNZChvf+tf
OoMY9K8vgNbhnGsUG6la7XPvZ+6dZMjdnxp2HB99Ml5A3PWZd75i5T6IHHxIQFbD
C3z9PWTWP+hK4k15DEyjlELtsE9WduGTXG4kUcf328xJ/7lj4VIImVugdCz+1B6z
+HlI6BiLwzY=
=YdVD
-----END PGP SIGNATURE-----
Merge tag 'md-3.9' of git://neil.brown.name/md
Pull md updates from NeilBrown:
"Mostly little bugfixes.
Only "feature" is a new RAID10 layout which slightly improves the
number of sets of devices that can concurrently fail, without data
loss."
* tag 'md-3.9' of git://neil.brown.name/md:
md: expedite metadata update when switching read-auto -> active
md: remove CONFIG_MULTICORE_RAID456
md/raid1,raid10: fix deadlock with freeze_array()
md/raid0: improve error message when converting RAID4-with-spares to RAID0
md: raid0: fix error return from create_stripe_zones.
md: fix two bugs when attempting to resize RAID0 array.
DM RAID: Add support for MD's RAID10 "far" and "offset" algorithms
MD RAID10: Improve redundancy for 'far' and 'offset' algorithms (part 2)
MD RAID10: Improve redundancy for 'far' and 'offset' algorithms (part 1)
MD RAID10: Minor non-functional code changes
md: raid1,10: Handle REQ_WRITE_SAME flag in write bios
md: protect against crash upon fsync on ro array
1) Some little fixes for the ad5064 dac driver.
2) A build warning 'fix' for a false positive in st_sensors
3) A couple of missing dependencies on IIO_BUFFER.
So nothing major and these mostly showed the advantages of the randconfig
builds various people have performed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=hA1D
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.9a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
"First round of iio fixes post the 3.9 merge window.
1) Some little fixes for the ad5064 dac driver.
2) A build warning 'fix' for a false positive in st_sensors
3) A couple of missing dependencies on IIO_BUFFER.
So nothing major and these mostly showed the advantages of the randconfig
builds various people have performed."
From the docs:
"IIR can queue up to two interrupt events. When the IIR is cleared,
it will set itself again after one clock if a second event was
stored."
"Only the rising edge of the PCH Display interrupt will cause the
North Display IIR (DEIIR) PCH Display Interrupt even bit to be set,
so all PCH Display Interrupts, including back to back interrupts,
must be cleared before a new PCH Display interrupt can cause DEIIR
to be set".
The current code works fine because we don't get many interrupts, but
if we enable the PCH FIFO underrun interrupts we'll start getting so
many interrupts that at some point new PCH interrupts won't cause
DEIIR to be set.
The initial implementation I tried was to turn the code that checks
SDEIIR into a loop, but we can still get interrupts even after the
loop is done (and before the irq handler finishes), so we have to
either disable the interrupts or mask them. In the end I concluded
that just disabling the PCH interrupts is enough, you don't even need
the loop, so this is what this patch implements. I've tested it and it
passes the 2 "PCH FIFO underrun interrupt storms" I can reproduce:
the "ironlake_crtc_disable" case and the "wrong watermarks" case.
In other words, here's how to reproduce the problem fixed by this
patch:
1 - Enable PCH FIFO underrun interrupts (SERR_INT on SNB+)
2 - Boot the machine
3 - While booting we'll get tons of PCH FIFO underrun interrupts
4 - Plug a new monitor
5 - Run xrandr, notice it won't detect the new monitor
6 - Read SDEIIR and notice it's not 0 while DEIIR is 0
Q: Can't we just clear DEIIR before SDEIIR?
A: It doesn't work. SDEIIR has to be completely cleared (including the
interrupts stored on its back queue) before it can flip DEIIR's bit to
1 again, and even while you're clearing it you'll be getting more and
more interrupts.
Q: Why does it work by just disabling+enabling the south interrupts?
A: Because when we re-enable them, if there's something on the SDEIIR
register (maybe an interrupt stored on the queue), the re-enabling
will make DEIIR's bit flip to 1, and since we'll already have
interrupts enabled we'll get another interrupt, then run our irq
handler again to process the "back" interrupts.
v2: Even bigger commit message, added code comments.
Note that this fixes missed dp aux irqs which have been reported for
3.9-rc1. This regression has been introduced by switching to
irq-driven dp aux transactions with
commit 9ee32fea5f
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat Dec 1 13:53:48 2012 +0100
drm/i915: irq-drive the dp aux communication
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18588.html
References: https://lkml.org/lkml/2013/2/26/769
Tested-by: Imre Deak <imre.deak@intel.com>
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Pimp commit message with references for the dp aux irq
timeout regression this fixes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the following sparse warning:
drivers/usb/musb/omap2430.c:54:33: warning: symbol '_glue' was not \
declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 80ab72e1 (usb: musb: omap2430: fix the readiness check
in omap_musb_mailbox) made the check incorrect, as we will lose the
glue/link status during the normal built-in probe order (twl4030_usb is
probed after musb omap2430, but before musb core is ready).
As a result, if you boot with USB cable on and load g_ether, the
connection does not work as the code thinks the cable is off and the
phy gets powered down immediately. This is a major regression in 3.9-rc1.
So the proper check should be: exit if _glue is NULL, but if it's
initialized we memorize the status, and then check if the musb core
is ready.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When running 100 randconfig iterations, I found
the following warning:
drivers/usb/musb/musb_core.c: In function ‘musb_init_controller’:
drivers/usb/musb/musb_core.c:1981:1: warning: label ‘fail5’ defined \
but not used [-Wunused-label]
this patch fixes it by removing the unnecessary
ifdef CONFIG_SYSFS.
Signed-off-by: Felipe Balbi <balbi@ti.com>
those are quite unnecessary, the only thing
we need to be careful about is USB_OTG_UTILS
which get properly selected by PHY drivers.
For now, MUSB will select only USB_OTG_UTILS
until we add stubs for the cases when PHY
layer isn't enabled.
Signed-off-by: Felipe Balbi <balbi@ti.com>
A few trivial fixes for composite driver:
Warning(include/linux/usb/composite.h:165): No description found for parameter
'fs_descriptors'
Warning(include/linux/usb/composite.h:165): Excess struct/union/enum/typedef
member 'descriptors' description in 'usb_function'
Warning(include/linux/usb/composite.h:321): No description found for parameter
'gadget_driver'
Warning(drivers/usb/gadget/composite.c:1777): Excess function parameter 'bind'
description in 'usb_composite_probe'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes a lockdep warning in igb_get_i2c_client by
refactoring the initialization and usage of the i2c_client
completely. There is no on the fly allocation of the single
client needed today.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need it to restore the ilk rc6 context, since the gpu wait no
requires interrupts. But in general having interrupts around should
help in code sanity, since more and more stuff is interrupt driven.
This regression has been introduced in
commit 3e9605018a
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Nov 27 16:22:54 2012 +0000
drm/i915: Rearrange code to only have a single method for waiting upon the ring
Like in the driver load code we need to make sure that hotplug
interrupts don't cause havoc with our modeset state, hence block them
with the existing infrastructure. Again we ignore races where we might
loose hotplug interrupts ...
Note that the driver load part of the regression has already been
fixed in
commit 52d7ecedac
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat Dec 1 21:03:22 2012 +0100
drm/i915: reorder setup sequence to have irqs for output setup
v2: Add a note to the commit message about which patch fixed the
driver load part of the regression. Stable kernels need to backport
both patches.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=54691
Cc: stable@vger.kernel.org (for 3.8 only, plese backport
52d7ecedac first)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reported-and-Tested-by: Ilya Tumaykin <itumaykin@gmail.com>
Reviewed-by: Chris wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch changes the setup copper link function to use a switch
statement for the PHY id's available for the given PHY types. It
also adds a case for the I210 PHY id, so the appropriate setup link
function is called for it.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On s390 the igb driver was throwing a build error due to the fact that a frame
built using build_skb would be larger than 2K. Since this is not likely to
change at any point in the future we are better off just dropping the check
since we already had a check in igb_set_rx_buffer_len that will just disable
the usage of build_skb anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This increases GEN6_RC6p_THRESHOLD from 100000 to 150000. For some
reason this avoids the gen6_gt_check_fifodbg.isra warnings and
associated GPU lockups, which makes my ivy bridge machine stable.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At 1000Mbps link speed, one of the MAC's internal clocks can be stopped for
up to 4us when entering K1 (a power mode of the MAC-PHY interconnect). If
the MAC is waiting for completion indications for 2 DMA write requests into
Host memory (e.g. descriptor writeback or Rx packet writing) and the
indications occur while the clock is stopped, both indications will be
missed by the MAC causing the MAC to wait for the completion indications
and be unable to generate further DMA write requests. This results in an
apparent hardware hang.
Work-around the issue by disabling the de-assertion of the clock request
when 1000Mbps link is acquired (K1 must be disabled while doing this).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
when strlen pi->location_code is larger than HVCS_CLC_LENGTH + 1,
original implementation can not let hvcsd->p_location_code NUL terminated.
so need fix it (also can simplify the code)
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove duplicate smp_twd clocks as these clocks are accessed using
DT now.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
In b1cffebf (ARM: GIC: remove direct use of gic_raise_softirq)
gic_raise_softirq() was moved inside arch/arm/common/gic.c but in the
process it reverted by mistake a change to that function made by
384a290 (ARM: gic: use a private mapping for CPU target interfaces).
This breaks multicluster systems on ARM.
This patch fixes the typo.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch (as1661) fixes a rather obscure bug in ehci-hcd. In a
couple of places, the driver compares the DMA address stored in a QH's
overlay region with the address of a particular qTD, in order to see
whether that qTD is the one currently being processed by the hardware.
(If it is then the status in the QH's overlay region is more
up-to-date than the status in the qTD, and if it isn't then the
overlay's value needs to be adjusted when the QH is added back to the
active schedule.)
However, DMA address in the overlay region isn't always valid. It
sometimes will contain a stale value, which may happen by coincidence
to be equal to a qTD's DMA address. Instead of checking the DMA
address, we should check whether the overlay region is active and
valid. The patch tests the ACTIVE bit in the overlay, and clears this
bit when the overlay becomes invalid (which happens when the
currently-executing URB is unlinked).
This is the second part of a fix for the regression reported at:
https://bugs.launchpad.net/bugs/1088733
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Reported-and-tested-by: Stephen Thirlwall <sdt@dr.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1660) works around a hardware problem present in some
(if not all) Intel EHCI controllers. After a QH has been unlinked
from the async schedule and the corresponding IAA interrupt has
occurred, the controller is not supposed access the QH and its qTDs.
There certainly shouldn't be any more DMA writes to those structures.
Nevertheless, Intel's controllers have been observed to perform a
final writeback to the QH's overlay region and to the most recent qTD.
For more information and a test program to determine whether this
problem is present in a particular controller, see
http://marc.info/?l=linux-usb&m=135492071812265&w=2http://marc.info/?l=linux-usb&m=136182570800963&w=2
This patch works around the problem by always waiting for two IAA
cycles when unlinking an async QH. The extra IAA delay gives the
controller time to perform its final writeback.
Surprisingly enough, the effects of this silicon bug have gone
undetected until quite recently. More through luck than anything
else, it hasn't caused any apparent problems. However, it does
interact badly with the path that follows this one, so it needs to be
addressed.
This is the first part of a fix for the regression reported at:
https://bugs.launchpad.net/bugs/1088733
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Stephen Thirlwall <sdt@dr.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
virtio_rng feeds the randomness buffer handed by the core directly
into the scatterlist, since commit bb347d9807.
However, if CONFIG_HW_RANDOM=m, the static buffer isn't a linear address
(at least on most archs). We could fix this in virtio_rng, but it's actually
far easier to just do it in the core as virtio_rng would have to allocate
a buffer every time (it doesn't know how much the core will want to read).
Reported-by: Aurelien Jarno <aurelien@aurel32.net>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Commit 16559ae4 (kgdb: remove #include <linux/serial_8250.h> from kgdb.h)
had a side effect of breaking omap1_defconfig build as some headers
were included indirectly:
arch/arm/mach-omap1/board-h2.c:249: error: ‘INT_KEYBOARD’ undeclared here (not in a function)
...
This worked earlier as linux/serial_8250.h included linux/serial_core.h,
via linux/serial_8250.h from linux/kgdb.h. Fix this by including the
necessary headers directly.
Signed-off-by: Tony Lindgren <tony@atomide.com>
build error cause by
Commit ff43da86c6
("NET: FEC: dynamtic check DMA desc buff type")
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_nextdesc’:
drivers/net/ethernet/freescale/fec.c:215:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_prevdesc’:
drivers/net/ethernet/freescale/fec.c:224:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_start_xmit’:
drivers/net/ethernet/freescale/fec.c:286:37: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:287:13: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:324:7: error: dereferencing pointer to incomplete type etc....
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6133705494 introduced a circular lock dependency because
posix_cpu_timers_exit() is called by release_task(), which is holding
a writer lock on tasklist_lock, and this can cause a deadlock since
kill_fasync() gets called with nonblocking_pool.lock taken.
There's no reason why kill_fasync() needs to be taken while the random
pool is locked, so move it out to fix this locking dependency.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reported-by: Russ Dill <Russ.Dill@gmail.com>
Cc: stable@kernel.org
On G45 some low res modes (800x600 and 1024x768) produce a blank
screen when the display plane is enabled with with cursor plane
off.
Experiments showed that this issue occurred when the following
conditions were met:
a. a previous mode had the cursor plane enabled (Xserver).
b. this mode or the previous one was using self refresh. (Thus
the problem was only seen with low res modes).
The screens lit up as soon as the cursor plane got enabled.
Therefore the blank screen occurred only in console mode, not
when running an Xserver.
It also seemed to be necessary to disable self refresh while briefly
enabling the cursor plane.
Signed-off-by: Egbert Eich <eich@suse.com>
Bugzilla: https://bugs.freedesktop.org/attachment.cgi?bugid=61457
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: drop spurious whitespace change.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After PCI and USB have stopped using the .find_bridge() callback in
struct acpi_bus_type, the only remaining user of it is SATA, but SATA
only pretends to be a user, because it points that callback to a stub
always returning -ENODEV.
For this reason, drop the SATA's dummy .find_bridge() callback and
remove .find_bridge(), which is not used any more, from struct
acpi_bus_type entirely.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
USB uses the .find_bridge() callback from struct acpi_bus_type
incorrectly, because as a result of the way it is used by USB every
device in the system that doesn't have a bus type or parent is
passed to usb_acpi_find_device() for inspection.
What USB actually needs, though, is to call usb_acpi_find_device()
for USB ports that don't have a bus type defined, but have
usb_port_device_type as their device type, as well as for USB
devices.
To fix that replace the struct bus_type pointer in struct
acpi_bus_type used for matching devices to specific subsystems
with a .match() callback to be used for this purpose and update
the users of struct acpi_bus_type, including USB, accordingly.
Define the .match() callback routine for USB, usb_acpi_bus_match(),
in such a way that it will cover both USB devices and USB ports
and remove the now redundant .find_bridge() callback pointer from
usb_acpi_bus.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
pr->id is u32 which never < 0, so remove the redundant pr->id < 0
check from acpi_processor_add().
[rjw: Changelog]
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
kfree() on a NULL pointer is a no-op, so remove a redundant NULL
pointer check in map_mat_entry().
[rjw: Changelog]
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Got this dmesg log on an Acer Aspire 725.
[ 0.256351] ACPI: (supports S0ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130117/hwxface-568)
[ 0.256373] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130117/hwxface-568)
[ 0.256391] S3 S4 S5)
Avoid this interleaving error messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Device PM QoS sysfs attributes, if present during device removal,
are removed from within device_pm_remove(), which is too late,
since dpm_sysfs_remove() has already removed the whole attribute
group they belonged to. However, moving the removal of those
attributes to dpm_sysfs_remove() alone is not sufficient, because
in theory they still can be re-added right after being removed by it
(the device's driver is still bound to it at that point).
For this reason, move the entire desctruction of device PM QoS
constraints to dpm_sysfs_remove() and make it prevent any new
constraints from being added after it has run. Also, move the
initialization of the power.qos field in struct device to
device_pm_init_common() and drop the no longer needed
dev_pm_qos_constraints_init().
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The current device PM QoS code assumes that certain functions will
never be called in parallel with each other (for example, it is
assumed that dev_pm_qos_expose_flags() won't be called in parallel
with dev_pm_qos_hide_flags() for the same device and analogously
for the latency limit), which may be overly optimistic. Moreover,
dev_pm_qos_expose_flags() and dev_pm_qos_expose_latency_limit()
leak memory in error code paths (req needs to be freed on errors)
and __dev_pm_qos_drop_user_request() forgets to free the request.
To fix the above issues put more things under the device PM QoS
mutex to make them mutually exclusive and add the missing freeing
of memory.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As uninitialized array members will be initialized to zero, we can
avoid using a for loop by setting a value to it.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-By: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix a typo in a comment in cpufreq_governor.h.
[rjw: Changelog]
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This flow happens when we get a failed single Tx response
on an AMPDU queue. In this case, the frame won't be sent
any more. So we need to move the window on the recipient
side. This is done by a BAR.
Now if we are in the following case: 10, 12 and 13 are ACKed
and 11 isn't.
10 11 12 13.
V X V V
Then, 11 will be sent 16 times as an MPDU (as oppsed to
A-MPDU). If this failed, we are entering the flow described
above. So we need to send a BAR with ssn = 12.
But in this case, the scheduler will tell us to free frames
up to 13 (included).
So, it is perfectly possible to get a failed single Tx
response on an AMPDU queue that makes the scheduler's ssn
jump by more than 1 single packet.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the rssi more accurate by taking in count per-chain AGC
values. Without this, the RSSI reports inaccurate values.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the device is being restarted, all the Rx / Tx Block
Ack sessions are been wiped out by the driver. So ignore
the requests from mac80211 that stops Tx agg while
reconfiguring the device.
Note that stopping a non-existing Rx BA session is harmless,
so just honor mac80211's request.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fix removes the override of calibration request values sent
to the FW.
Due to that, the sending of default values to now implemented
calibrations is removed.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The phy_cfg is given from the TLV value and does not have to be
built by us.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We must set the valid TX antennas number in the ucode before
sending the phy_cfg_cmd and request for calibrations.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This situation is clearly an error situation and the only
way to recover is to restart the driver / fw.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should return here with an error code instead of continuing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Smatch complains that "len" could be larger than the sizeof(value)
so we could be copying garbage here. I have changed this to match
how things are done in composite_setup().
The call tree looks like:
composite_setup()
--> f_audio_setup()
--> audio_get_intf_req()
composite_setup() expects the return value to be set to
sizeof(value).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We added a warning to flush_to_ldisc to report cases when it is called
with a NULL tty. It was for debugging purposes and it lead to a
patchset from Peter Hurley. The patchset however did not make it to
3.9, so disable the warning now to not disturb people.
We can re-add it when the series is in and we are hunting for another
bugs.
Reported-by: David Miller <davem@davemloft.net>
Cc: stable <stable@vger.kernel.org> # 3.8
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In patch "5d3c28b usb: otg: add device tree support to otg library"
devm_usb_get_phy_by_phandle() was added. It uses try_module_get() to lock the
phy driver in memory. The corresponding module_put() is missing in that patch.
This patch adds try_module_get() to usb_get_phy() and usb_get_phy_dev().
Further the missing module_put() is added to usb_put_phy().
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently it is possible to have:
USB_MUSB_OMAP2PLUS=m
TWL4030_USB=y
which would result compile time error due to missing symbols.
With this change USB_MUSB_OMAP2PLUS and TWL4030_USB will be in sync.
Reported-by: Vincent Stehle <v-stehle@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whenever ->udc_start() gets called, gadget driver
has already being bound to the udc controller, which
means that gadget->dev had to be already initialized
and added to driver model.
This patch fixes imx_udc mistake.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whenever ->udc_start() gets called, gadget driver
has already being bound to the udc controller, which
means that gadget->dev had to be already initialized
and added to driver model.
This patch fixes pxa25x mistake.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whenever ->udc_start() gets called, gadget driver
has already being bound to the udc controller, which
means that gadget->dev had to be already initialized
and added to driver model.
This patch fixes s3c2410 mistake.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The current ordering in makefile makes gadget
drivers be loaded before usb functions which
causes usb_get_function_instance() to fail when
gadget modules are statically linked to the
kernel binary.
Changed the ordering here so that USB functions
are loaded before gadget drivers.
Note that this is only a temporary solution and
a more robust fix is needed in the long run.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whenever ->udc_start() gets called, gadget driver
has already being bound to the udc controller, which
means that gadget->dev had to be already initialized
and added to driver model.
This patch fixes pxa27x mistake.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
the params variables on dwc3_gadget_conndone_interrupt()
is only memset() to zero but never used in
that function, so we can safely drop the variable
and memset() call.
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 3921426 (usb: dwc3: core: move
event buffer allocation out of
dwc3_core_init()) introduced a memory leak
of the coherent memory we use as event
buffers on dwc3 driver.
If the driver is compiled as a dynamically
loadable module and use constantly loads
and unloads the driver, we will continue
to leak the coherent memory allocated during
->probe() because dwc3_free_event_buffers()
is never called during ->remove().
Cc: <stable@vger.kernel.org> # v3.7 v3.8
Signed-off-by: Felipe Balbi <balbi@ti.com>
Not having power is a pretty serious error so check that we are able to
enable the supply and error out if we can't.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org #3.8+; 3.0+ will need manual backport
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We read the chip ID from the chip, use it to determine if the chip ID provided
to the driver is correct, and report it if wrong. We should also use the
correct chip ID to select supported functionality.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.2+
Acked-by: Jean Delvare <khali@linux-fr.org>
Peak attributes were not initialized and cleared correctly.
Also, temp2_max is only supported on page 0 and thus does not need to be
an array.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.2+
Acked-by: Jean Delvare <khali@linux-fr.org>
Modify the request_module to prefix the file system type with "fs-"
and add aliases to all of the filesystems that can be built as modules
to match.
A common practice is to build all of the kernel code and leave code
that is not commonly needed as modules, with the result that many
users are exposed to any bug anywhere in the kernel.
Looking for filesystems with a fs- prefix limits the pool of possible
modules that can be loaded by mount to just filesystems trivially
making things safer with no real cost.
Using aliases means user space can control the policy of which
filesystem modules are auto-loaded by editing /etc/modprobe.d/*.conf
with blacklist and alias directives. Allowing simple, safe,
well understood work-arounds to known problematic software.
This also addresses a rare but unfortunate problem where the filesystem
name is not the same as it's module name and module auto-loading
would not work. While writing this patch I saw a handful of such
cases. The most significant being autofs that lives in the module
autofs4.
This is relevant to user namespaces because we can reach the request
module in get_fs_type() without having any special permissions, and
people get uncomfortable when a user specified string (in this case
the filesystem type) goes all of the way to request_module.
After having looked at this issue I don't think there is any
particular reason to perform any filtering or permission checks beyond
making it clear in the module request that we want a filesystem
module. The common pattern in the kernel is to call request_module()
without regards to the users permissions. In general all a filesystem
module does once loaded is call register_filesystem() and go to sleep.
Which means there is not much attack surface exposed by loading a
filesytem module unless the filesystem is mounted. In a user
namespace filesystems are not mounted unless .fs_flags = FS_USERNS_MOUNT,
which most filesystems do not set today.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Reported-by: Kees Cook <keescook@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Fixes issue where i2c subdev never gets destroyed due to its subobjects
holding references. This will mean the i2c subdev refcount goes
negative during its destruction, but this isn't an issue in practice.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes script-based modesetting on some LVDS panels.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- Update the Xen ACPI memory and CPU hotplug locking mechanism.
- Fix PAT issues wherein various applications would not start
- Fix handling of multiple MSI as AHCI now does it.
- Fix ARM compile failures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRMM+8AAoJEFjIrFwIi8fJnGsIANU/lVS5EwV6ZMP9GiVtbm68
sBn0MoDIkN2ID16gcrQdfvzgtTQHsptL2fOl756veTHN2AIpIFYShKZpbgR9VM+c
MpD68ltakkfjoVeb7F7yPbDvcSftKRW5VAq1SeFMc2gOOmiqAWQGgBC+3Cd04zFk
SqzDs1RLUHypwBOFlZKa1ex/ShuYfzRb9x+J6zqGO+OpjhlMobyag8rhSlgehlfP
6gS1IzmcH8a6SgBKZk/+YC+i+QLgPOyxiK6zcxa2rfc6iUwodpqBpKP1N+CS4lnu
FIKOIIzzCwCEAq94wVV0GJwHyw7nsqjG8syfRyOPmauLrpOI70xrV+lYFMVVRA0=
=HwzV
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
- Update the Xen ACPI memory and CPU hotplug locking mechanism.
- Fix PAT issues wherein various applications would not start
- Fix handling of multiple MSI as AHCI now does it.
- Fix ARM compile failures.
* tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus: fix compile failure on ARM with Xen enabled
xen/pci: We don't do multiple MSI's.
xen/pat: Disable PAT using pat_enabled value.
xen/acpi: xen cpu hotplug minor updates
xen/acpi: xen memory hotplug minor updates
Pull more VFS bits from Al Viro:
"Unfortunately, it looks like xattr series will have to wait until the
next cycle ;-/
This pile contains 9p cleanups and fixes (races in v9fs_fid_add()
etc), fixup for nommu breakage in shmem.c, several cleanups and a bit
more file_inode() work"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
constify path_get/path_put and fs_struct.c stuff
fix nommu breakage in shmem.c
cache the value of file_inode() in struct file
9p: if v9fs_fid_lookup() gets to asking server, it'd better have hashed dentry
9p: make sure ->lookup() adds fid to the right dentry
9p: untangle ->lookup() a bit
9p: double iput() in ->lookup() if d_materialise_unique() fails
9p: v9fs_fid_add() can't fail now
v9fs: get rid of v9fs_dentry
9p: turn fid->dlist into hlist
9p: don't bother with private lock in ->d_fsdata; dentry->d_lock will do just fine
more file_inode() open-coded instances
selinux: opened file can't have NULL or negative ->f_path.dentry
(In the meantime, the hlist traversal macros have changed, so this
required a semantic conflict fixup for the newly hlistified fid->dlist)
Pull second set of s390 patches from Martin Schwidefsky:
"The main part of this merge are Heikos uaccess patches. Together with
commit 0988496433 ("mm: do not grow the stack vma just because of an
overrun on preceding vma") the user string access is hopefully fixed
for good.
In addition some bug fixes and two cleanup patches."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/module: fix compile warning
qdio: remove unused parameters
s390/uaccess: fix kernel ds access for page table walk
s390/uaccess: fix strncpy_from_user string length check
input: disable i8042 PC Keyboard controller for s390
s390/dis: Fix invalid array size
s390/uaccess: remove pointless access_ok() checks
s390/uaccess: fix strncpy_from_user/strnlen_user zero maxlen case
s390/uaccess: shorten strncpy_from_user/strnlen_user
s390/dasd: fix unresponsive device after all channel paths were lost
s390/mm: ignore change bit for vmemmap
s390/page table dumper: add support for change-recording override bit
Pull second round of PARISC updates from Helge Deller:
"The most important fix in this branch is the switch of io_setup,
io_getevents and io_submit syscalls to use the available compat
syscalls when running 32bit userspace on 64bit kernel. Other than
that it's mostly removal of compile warnings."
* 'fixes-for-3.9-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix redefinition of SET_PERSONALITY
parisc: do not install modules when installing kernel
parisc: fix compile warnings triggered by atomic_sub(sizeof(),v)
parisc: check return value of down_interruptible() in hp_sdc_rtc.c
parisc: avoid unitialized variable warning in pa_memcpy()
parisc: remove unused variable 'compat_val'
parisc: switch to compat_functions of io_setup, io_getevents and io_submit
parisc: select ARCH_WANT_FRAME_POINTERS
This adds core architecture support for Imagination's Meta processor
cores, followed by some later miscellaneous arch/metag cleanups and
fixes which I kept separate to ease review:
- Support for basic Meta 1 (ATP) and Meta 2 (HTP) core architecture
- A few fixes all over, particularly for symbol prefixes
- A few privilege protection fixes
- Several cleanups (setup.c includes, split out a lot of metag_ksyms.c)
- Fix some missing exports
- Convert hugetlb to use vm_unmapped_area()
- Copy device tree to non-init memory
- Provide dma_get_sgtable()
Signed-off-by: James Hogan <james.hogan@imgtec.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=65cR
-----END PGP SIGNATURE-----
Merge tag 'metag-v3.9-rc1-v4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull new ImgTec Meta architecture from James Hogan:
"This adds core architecture support for Imagination's Meta processor
cores, followed by some later miscellaneous arch/metag cleanups and
fixes which I kept separate to ease review:
- Support for basic Meta 1 (ATP) and Meta 2 (HTP) core architecture
- A few fixes all over, particularly for symbol prefixes
- A few privilege protection fixes
- Several cleanups (setup.c includes, split out a lot of
metag_ksyms.c)
- Fix some missing exports
- Convert hugetlb to use vm_unmapped_area()
- Copy device tree to non-init memory
- Provide dma_get_sgtable()"
* tag 'metag-v3.9-rc1-v4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag: (61 commits)
metag: Provide dma_get_sgtable()
metag: prom.h: remove declaration of metag_dt_memblock_reserve()
metag: copy devicetree to non-init memory
metag: cleanup metag_ksyms.c includes
metag: move mm/init.c exports out of metag_ksyms.c
metag: move usercopy.c exports out of metag_ksyms.c
metag: move setup.c exports out of metag_ksyms.c
metag: move kick.c exports out of metag_ksyms.c
metag: move traps.c exports out of metag_ksyms.c
metag: move irq enable out of irqflags.h on SMP
genksyms: fix metag symbol prefix on crc symbols
metag: hugetlb: convert to vm_unmapped_area()
metag: export clear_page and copy_page
metag: export metag_code_cache_flush_all
metag: protect more non-MMU memory regions
metag: make TXPRIVEXT bits explicit
metag: kernel/setup.c: sort includes
perf: Enable building perf tools for Meta
metag: add boot time LNKGET/LNKSET check
metag: add __init to metag_cache_probe()
...
Pull late ARM updates from Russell King:
"Here is the late set of ARM updates for this merge window; in here is:
- The ARM parts of the broadcast timer support, core parts merged
through tglx's tree. This was left over from the previous merge to
allow the dependency on tglx's tree to be resolved.
- A fix to the VFP code which shows up on Raspberry Pi's, as well as
fixing the fallout from a previous commit in this area.
- A number of smaller fixes scattered throughout the ARM tree"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: Fix broken commit 0cc41e4a21 corrupting kernel messages
ARM: fix scheduling while atomic warning in alignment handling code
ARM: VFP: fix emulation of second VFP instruction
ARM: 7656/1: uImage: Error out on build of multiplatform without LOADADDR
ARM: 7640/1: memory: tegra_ahb_enable_smmu() depends on TEGRA_IOMMU_SMMU
ARM: 7654/1: Preserve L_PTE_VALID in pte_modify()
ARM: 7653/2: do not scale loops_per_jiffy when using a constant delay clock
ARM: 7651/1: remove unused smp_timer_broadcast #define
The second digit was off by one, which meant we accidentally treated
GT(n) as GT(n-1). This also meant no support for GT1 at all.
Cc: stable@kernel.org
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Restore crtc->fb to the old framebuffer if queue_flip fails.
While at it, kill the pointless intel_fb temp variable.
v2: Update crtc->fb before queue_flip and restore it back
after a failure.
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Here is one remaining patch for 3.9-rc1. It is for the hyper-v drivers, and
had to wait until some other patches went in through the x86 tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlExO5kACgkQMUfUDdst+ylRogCfcZN5nq3gZ8bUb5CTjQF38m1h
41UAnAoFnIiV3QZhjmaf2x+mN+SEyel7
=EqqO
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc patch from Greg Kroah-Hartman:
"Here is one remaining patch for 3.9-rc1. It is for the hyper-v
drivers, and had to wait until some other patches went in through the
x86 tree."
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: Use the new infrastructure for delivering VMBUS interrupts
Here is one remaining USB patch for 3.9-rc1, it reverts a 3.8 patch that has
caused a lot of regressions for some VIA EHCI controllers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlExO/QACgkQMUfUDdst+yny+wCeO71iPtYEPUCl3uiE3TfzYBfW
kNwAoNJT7mDkFpjJV2TWOYbQCb48pY9r
=jJ6t
-----END PGP SIGNATURE-----
Merge tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patch revert from Greg Kroah-Hartman:
"Here is one remaining USB patch for 3.9-rc1, it reverts a 3.8 patch
that has caused a lot of regressions for some VIA EHCI controllers."
* tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: EHCI: revert "remove ASS/PSS polling timeout"
Pull watchdog updates from Wim Van Sebroeck:
"This contains:
- fixes and improvements
- devicetree bindings
- conversion to watchdog generic framework of the following drivers:
- booke_wdt
- bcm47xx_wdt.c
- at91sam9_wdt
- Removal of old STMP3xxx driver
- Addition of following new drivers:
- new driver for STMP3xxx and i.MX23/28
- Retu watchdog driver"
* git://www.linux-watchdog.org/linux-watchdog: (30 commits)
watchdog: sp805_wdt depends on ARM
watchdog: davinci_wdt: update to devm_* API
watchdog: davinci_wdt: use devm managed clk get
watchdog: at91rm9200: add DT support
watchdog: add timeout-sec property binding
watchdog: at91sam9_wdt: Convert to use the watchdog framework
watchdog: omap_wdt: Add option nowayout
watchdog: core: dt: add support for the timeout-sec dt property
watchdog: bcm47xx_wdt.c: add hard timer
watchdog: bcm47xx_wdt.c: rename wdt_time to timeout
watchdog: bcm47xx_wdt.c: rename ops methods
watchdog: bcm47xx_wdt.c: use platform device
watchdog: bcm47xx_wdt.c: convert to watchdog core api
watchdog: Convert BookE watchdog driver to watchdog infrastructure
watchdog: s3c2410_wdt: Use devm_* functions
watchdog: remove old STMP3xxx driver
watchdog: add new driver for STMP3xxx and i.MX23/28
rtc: stmp3xxx: add wdt-accessor function
watchdog: introduce retu_wdt driver
watchdog: intel_scu_watchdog: fix Kconfig dependency
...
Pull second set of slave-dmaengine updates from Vinod Koul:
"Arnd's patch moves the dw_dmac to use generic DMA binding. I agreed
to merge this late as it will avoid the conflicts between trees.
The second patch from Matt adding a dma_request_slave_channel_compat
API was supposed to be picked up, but somehow never got picked up.
Some patches dependent on this are already in -next :("
* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dw_dmac: move to generic DMA binding
dmaengine: add dma_request_slave_channel_compat()
Pull x86 platform driver updates from Matthew Garrett:
"Mostly relatively small updates, along with some hardware enablement
for Sony hardware and a pile of updates to Google's Chromebook driver"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (49 commits)
ideapad-laptop: Depend on BACKLIGHT_CLASS_DEVICE instead of selecting it
ideapad: depends on backlight subsystem and update comment
Platform: x86: chromeos_laptop - add i915 gmbuses to adapter names
Platform: x86: chromeos_laptop - Add isl light sensor for Pixel
Platform: x86: chromeos_laptop - Add a more general add_i2c_device
Platform: x86: chromeos_laptop - Add Pixel Touchscreen
Platform: x86: chromeos_laptop - Add support for probing devices
Platform: x86: chromeos_laptop - Add Pixel Trackpad
hp-wmi: fix handling of platform device
sony-laptop: leak in error handling sony_nc_lid_resume_setup()
hp-wmi: Add support for SMBus hotkeys
asus-wmi: Fix unused function build warning
acer-wmi: avoid the warning of 'devices' may be used uninitialized
drivers/platform/x86/thinkpad_acpi.c: Handle HKEY event 0x6040
Platform: x86: chromeos_laptop - Add HP Pavilion 14
Platform: x86: chromeos_laptop - Add Taos tsl2583 device
Platform: x86: chromeos_laptop - Add Taos tsl2563 device
Platform: x86: chromeos_laptop - Add Acer C7 trackpad
Platform: x86: chromeos_laptop - Rename setup_lumpy_tp to setup_cyapa_smbus_tp
asus-laptop: always report brightness key events
...
So use msecs_to_jiffies(10) to make the timeout the same as in the
"!has_aux_irq" case.
This patch was initially written by Daniel Vetter and posted on
pastebin a few weeks ago. I'm just bringing it to the mailing list.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Need to initialize the variable wait to false.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a resubmission.
Added kfree() in ax88179_get_eeprom to prevent memory leakage.
Modified "__le16 rxctl" to "u16 rxctl" in "struct ax88179_data" and removed pointless casts.
Removed asix_init and asix_exit functions and added "module_usb_driver(ax88179_178a_driver)".
Fixed endianness issue on big endian systems and verified this driver on iBook G4.
Removed steps that change net->features in ax88179_set_features function.
Added "const" to ethtool_ops structure and fixed the coding style of AX88179_BULKIN_SIZE array.
Fixed the issue that the default MTU is not 1500.
Added ax88179_change_mtu function and enabled the hardware jumbo frame function to support an
MTU higher than 1500.
Fixed indentation and empty line coding style errors.
The _nopm version usb functions were added to access register in suspend and resume functions.
Serveral variables allocted dynamically were removed and replaced by stack variables.
ax88179_get_eeprom were modified from asix_get_eeprom in asix_common.
This patch adds a driver for ASIX's AX88179 family of USB 3.0/2.0
to gigabit ethernet adapters. It's based on the AX88xxx driver but
the usb commands used to access registers for AX88179 are completely different.
This driver had been verified on x86 system with AX88179/AX88178A and
Sitcomm LN-032 USB dongles.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
* misc clean-ups in the MTD command-line partitioning parser (cmdlinepart)
* add flash locking support for STmicro chips serial flash chips, as well as
for CFI command set 2 chips.
* new driver for the ELM error correction HW module found in various TI chips,
enable the OMAP NAND driver to use the ELM HW error correction
* added number of new serial flash IDs
* various fixes and improvements in the gpmi NAND driver
* bcm47xx NAND driver improvements
* make the mtdpart module actually removable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iEYEABECAAYFAlExEs8ACgkQdwG7hYl686Oa+gCgiBNt+I0MiixDeN+MGuE1uw9s
i2wAniD9sR2HDy6y5SkbdXK/aPr8ez/p
=xV1l
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20130301' of git://git.infradead.org/linux-mtd
Pull MTD update from David Woodhouse:
"Fairly unexciting MTD merge for 3.9:
- misc clean-ups in the MTD command-line partitioning parser
(cmdlinepart)
- add flash locking support for STmicro chips serial flash chips, as
well as for CFI command set 2 chips.
- new driver for the ELM error correction HW module found in various
TI chips, enable the OMAP NAND driver to use the ELM HW error
correction
- added number of new serial flash IDs
- various fixes and improvements in the gpmi NAND driver
- bcm47xx NAND driver improvements
- make the mtdpart module actually removable"
* tag 'for-linus-20130301' of git://git.infradead.org/linux-mtd: (45 commits)
mtd: map: BUG() in non handled cases
mtd: bcm47xxnflash: use pr_fmt for module prefix in messages
mtd: davinci_nand: Use managed resources
mtd: mtd_torturetest can cause stack overflows
mtd: physmap_of: Convert device allocation to managed devm_kzalloc()
mtd: at91: atmel_nand: for PMECC, add code to check the ONFI parameter ECC requirement.
mtd: atmel_nand: make pmecc-cap, pmecc-sector-size in dts is optional.
mtd: atmel_nand: avoid to report an error when lookup table offset is 0.
mtd: bcm47xxsflash: adjust names of bus-specific functions
mtd: bcm47xxpart: improve probing of nvram partition
mtd: bcm47xxpart: add support for other erase sizes
mtd: bcm47xxnflash: register this as normal driver
mtd: bcm47xxnflash: fix message
mtd: bcm47xxsflash: register this as normal driver
mtd: bcm47xxsflash: write number of written bytes
mtd: gpmi: add sanity check for the ECC
mtd: gpmi: set the Golois Field bit for mx6q's BCH
mtd: devices: elm: Removes <xx> literals in elm DT node
mtd: gpmi: fix a dereferencing freed memory error
mtd: fix the wrong timeo for panic_nand_wait()
...
Meta core internal interrupts (from HWSTATMETA and friends) are vectored
onto the TR1 core trigger for the current thread. This is demultiplexed
in irq-metag.c to individual Linux IRQs for each internal interrupt.
External SoC interrupts (from HWSTATEXT and friends) are vectored onto
the TR2 core trigger for the current thread. This is demultiplexed in
irq-metag-ext.c to individual Linux IRQs for each external SoC interrupt.
The external irqchip has devicetree bindings for configuring the number
of irq banks and the type of masking available.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Dom Cobley <popcornmix@gmail.com>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-doc@vger.kernel.org
Add time keeping code for metag. Meta hardware threads have 2 timers.
The background timer (TXTIMER) is used as a free-running time base, and
the interrupt timer (TXTIMERI) is used for the timer interrupt. Both
counters traditionally count at approximately 1MHz.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
an SSD to be used as a cache in front of a slower device. Cache
tuning is delegated to interchangeable policy modules so these can
be developed independently of the mechanics needed to shuffle the
data around.
Other than that, kcopyd users acquire a throttling parameter, ioctl
buffer usage gets streamlined, more mempool reliance is reduced
and there are a few other bug fixes and tidy-ups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yXuO
-----END PGP SIGNATURE-----
Merge tag 'dm-3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper update from Alasdair G Kergon:
"The main addition here is a long-desired target framework to allow an
SSD to be used as a cache in front of a slower device. Cache tuning
is delegated to interchangeable policy modules so these can be
developed independently of the mechanics needed to shuffle the data
around.
Other than that, kcopyd users acquire a throttling parameter, ioctl
buffer usage gets streamlined, more mempool reliance is reduced and
there are a few other bug fixes and tidy-ups."
* tag 'dm-3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: (30 commits)
dm cache: add cleaner policy
dm cache: add mq policy
dm: add cache target
dm persistent data: add bitset
dm persistent data: add transactional array
dm thin: remove cells from stack
dm bio prison: pass cell memory in
dm persistent data: add btree_walk
dm: add target num_write_bios fn
dm kcopyd: introduce configurable throttling
dm ioctl: allow message to return data
dm ioctl: optimize functions without variable params
dm ioctl: introduce ioctl_flags
dm: merge io_pool and tio_pool
dm: remove unused _rq_bio_info_cache
dm: fix limits initialization when there are no data devices
dm snapshot: add missing module aliases
dm persistent data: set some btree fn parms const
dm: refactor bio cloning
dm: rename bio cloning functions
...
Pull SCSI target patches from Nicholas Bellinger:
"Here are the remaining target-pending patches for v3.9-rc1.
The most important one here is the immediate queue starvation
regression fix for iscsi-target, which addresses a bug that's
effecting v3.5+ kernels under heavy sustained READ only workloads.
Thanks alot to Benjamin Estrabaud for helping to track this down!
Also included is a pSCSI exception bugfix from Asias, along with a
handful of other minor changes. Both bugfixes are CC'ed to stable."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/pscsi: Rename sg_num to nr_vecs in pscsi_get_bio()
target/pscsi: Fix page increment
target/pscsi: Drop unnecessary NULL assignment to bio->bi_next
target: Add __exit annotation for module_exit functions
iscsi-target: Fix immediate queue starvation regression with DATAIN
This is an assorted set of stragglers into the merge window with driver
updates for qla2xxx, megaraid_sas, storvsc and ufs. It also includes pulls of
the uapi tree (all the remaining SCSI pieces) and the fcoe tree (updates to
fcoe and libfc)
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRMHJHAAoJEDeqqVYsXL0M9tAH/2YG3TCfy0RFAejGgLfX9OGH
6eFe71m7Z8nfIEneAnm5BuKjCx3QFRp5UFjJZdFHLP1Qv0TbpKs4FnZyeSGTxLQp
S1fZc5sTWmsb5qYxLaukKopC6sFx+hNI2dvB+rgKcd+nWy1RzG7lGqbS4CRNE76q
UNByqlfqJxn5cfQw7dg2zOUKlGaGL2jSyFf0QFXR2IZzO33PeyBPfKDFeJC6b+oc
XTy9MK9V5u6ne3XimDTU2hP4lPAsZaJtcqsv1Gvv2y+BHalQiPqfL6bZMvN3Zbfq
hfT+i2xnYy85858gxtyIhzHwU14zF7I0HEWiVpddsF9NDK7iNKvK8aWHaTs7qis=
=hvGQ
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is an assorted set of stragglers into the merge window with
driver updates for qla2xxx, megaraid_sas, storvsc and ufs.
It also includes pulls of the uapi tree (all the remaining SCSI
pieces) and the fcoe tree (updates to fcoe and libfc)"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (81 commits)
[SCSI] ufs: Separate PCI code into glue driver
[SCSI] ufs: Segregate PCI Specific Code
[SCSI] scsi: fix lpfc build when wmb() is defined as mb()
[SCSI] storvsc: Handle dynamic resizing of the device
[SCSI] storvsc: Restructure error handling code on command completion
[SCSI] storvsc: avoid usage of WRITE_SAME
[SCSI] aacraid: suppress two GCC warnings
[SCSI] hpsa: check for dma_mapping_error in hpsa_passthru ioctls
[SCSI] hpsa: reorganize error handling in hpsa_passthru_ioctl
[SCSI] hpsa: check for dma_mapping_error in hpsa_map_sg_chain_block
[SCSI] hpsa: Check for dma_mapping_error for all code paths using fill_cmd
[SCSI] hpsa: Check for dma_mapping_error in hpsa_map_one
[SCSI] dc395x: uninitialized variable in device_alloc()
[SCSI] Fix range check in scsi_host_dif_capable()
[SCSI] storvsc: Initialize the sglist
[SCSI] mpt2sas: Add support for OEM specific controller
[SCSI] ipr: Fix oops while resetting an ipr adapter
[SCSI] fnic: Fnic Trace Utility
[SCSI] fnic: New debug flags and debug log messages
[SCSI] fnic: fnic driver may hit BUG_ON on device reset
...
Tim found:
WARNING: at arch/x86/kernel/smpboot.c:324 topology_sane.isra.2+0x6f/0x80()
Hardware name: S2600CP
sched: CPU #1's llc-sibling CPU #0 is not on the same node! [node: 1 != 0]. Ignoring dependency.
smpboot: Booting Node 1, Processors #1
Modules linked in:
Pid: 0, comm: swapper/1 Not tainted 3.9.0-0-generic #1
Call Trace:
set_cpu_sibling_map+0x279/0x449
start_secondary+0x11d/0x1e5
Don Morris reproduced on a HP z620 workstation, and bisected it to
commit e8d1955258 ("acpi, memory-hotplug: parse SRAT before memblock
is ready")
It turns out movable_map has some problems, and it breaks several things
1. numa_init is called several times, NOT just for srat. so those
nodes_clear(numa_nodes_parsed)
memset(&numa_meminfo, 0, sizeof(numa_meminfo))
can not be just removed. Need to consider sequence is: numaq, srat, amd, dummy.
and make fall back path working.
2. simply split acpi_numa_init to early_parse_srat.
a. that early_parse_srat is NOT called for ia64, so you break ia64.
b. for (i = 0; i < MAX_LOCAL_APIC; i++)
set_apicid_to_node(i, NUMA_NO_NODE)
still left in numa_init. So it will just clear result from early_parse_srat.
it should be moved before that....
c. it breaks ACPI_TABLE_OVERIDE...as the acpi table scan is moved
early before override from INITRD is settled.
3. that patch TITLE is total misleading, there is NO x86 in the title,
but it changes critical x86 code. It caused x86 guys did not
pay attention to find the problem early. Those patches really should
be routed via tip/x86/mm.
4. after that commit, following range can not use movable ram:
a. real_mode code.... well..funny, legacy Node0 [0,1M) could be hot-removed?
b. initrd... it will be freed after booting, so it could be on movable...
c. crashkernel for kdump...: looks like we can not put kdump kernel above 4G
anymore.
d. init_mem_mapping: can not put page table high anymore.
e. initmem_init: vmemmap can not be high local node anymore. That is
not good.
If node is hotplugable, the mem related range like page table and
vmemmap could be on the that node without problem and should be on that
node.
We have workaround patch that could fix some problems, but some can not
be fixed.
So just remove that offending commit and related ones including:
f7210e6c4a ("mm/memblock.c: use CONFIG_HAVE_MEMBLOCK_NODE_MAP to
protect movablecore_map in memblock_overlaps_region().")
01a178a94e ("acpi, memory-hotplug: support getting hotplug info from
SRAT")
27168d38fa ("acpi, memory-hotplug: extend movablemem_map ranges to
the end of node")
e8d1955258 ("acpi, memory-hotplug: parse SRAT before memblock is
ready")
fb06bc8e5f ("page_alloc: bootmem limit with movablecore_map")
42f47e27e7 ("page_alloc: make movablemem_map have higher priority")
6981ec3114 ("page_alloc: introduce zone_movable_limit[] to keep
movable limit for nodes")
34b71f1e04 ("page_alloc: add movable_memmap kernel parameter")
4d59a75125 ("x86: get pg_data_t's memory from other node")
Later we should have patches that will make sure kernel put page table
and vmemmap on local node ram instead of push them down to node0. Also
need to find way to put other kernel used ram to local node ram.
Reported-by: Tim Gardner <tim.gardner@canonical.com>
Reported-by: Don Morris <don.morris@hp.com>
Bisected-by: Don Morris <don.morris@hp.com>
Tested-by: Don Morris <don.morris@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanups
Remove kdb ssb command - there is no in kernel disassembler to support it
Remove kdb ll command - Always caused a kernel oops and there were no
bug reports so no one was using this command
Use kernel ARRAY_SIZE macro instead of array computations
Fixes
Stop oops in kdb if user executes kdb_defcmd with args
kdb help command truncated text
ppc64 support for kgdbts
Add missing kconfig option from original kdb port for dealing with
catastrophic kernel crashes such that you can reboot automatically
on continue from kdb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Hwbq
-----END PGP SIGNATURE-----
Merge tag 'for_linux-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB fixes and cleanups from Jason Wessel:
"For a change we removed more code than we added. If people aren't
using it we shouldn't be carrying it. :-)
Cleanups:
- Remove kdb ssb command - there is no in kernel disassembler to
support it
- Remove kdb ll command - Always caused a kernel oops and there were
no bug reports so no one was using this command
- Use kernel ARRAY_SIZE macro instead of array computations
Fixes:
- Stop oops in kdb if user executes kdb_defcmd with args
- kdb help command truncated text
- ppc64 support for kgdbts
- Add missing kconfig option from original kdb port for dealing with
catastrophic kernel crashes such that you can reboot automatically
on continue from kdb"
* tag 'for_linux-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
kdb: Remove unhandled ssb command
kdb: Prevent kernel oops with kdb_defcmd
kdb: Remove the ll command
kdb_main: fix help print
kdb: Fix overlap in buffers with strcpy
Fixed dead ifdef block by adding missing Kconfig option.
kdb: Setup basic kdb state before invoking commands via kgdb
kdb: use ARRAY_SIZE where possible
kgdb/kgdbts: support ppc64
kdb: A fix for kdb command table expansion
Fix:
drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c: In function ‘inv_mpu6050_read_fifo’:
drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c:176:3: error: implicit declaration of
function ‘iio_push_to_buffers’ [-Werror=implicit-function-declaration]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Initialize the register cache to the proper mid-scale value based on the
resolution of the device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The DAC value range check allows values one larger than the maximum value, which
effectively results in setting the DAC value to 0. This patch fixes the issue.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ad5065, ad5045, ad5025 use address '3' for the second channel, so they need
their own channel spec.
Note that ad5064_sync_powerdown_mode() also needs to be slightly updated since
it was relying on the fact that chan->address always equaled chan->channel.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pull MIPS updates from Ralf Baechle:
o Add basic support for the Mediatek/Ralink Wireless SoC family.
o The Qualcomm Atheros platform is extended by support for the new
QCA955X SoC series as well as a bunch of patches that get the code
ready for OF support.
o Lantiq and BCM47XX platform have a few improvements and bug fixes.
o MIPS has sent a few patches that get the kernel ready for the
upcoming microMIPS support.
o The rest of the series is made up of small bug fixes and cleanups
that relate to various parts of the MIPS code. The biggy in there is
a whitespace cleanup. After I was sent another set of whitespace
cleanup patches I decided it was the time to clean the whitespace
"issues" for once and and that touches many files below arch/mips/.
Fix up silly conflicts, mostly due to whitespace cleanups.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (105 commits)
MIPS: Quit exporting kernel internel break codes to uapi/asm/break.h
MIPS: remove broken conditional inside vpe loader code
MIPS: SMTC: fix implicit declaration of set_vi_handler
MIPS: early_printk: drop __init annotations
MIPS: Probe for and report hardware virtualization support.
MIPS: ath79: add support for the Qualcomm Atheros AP136-010 board
MIPS: ath79: add USB controller registration code for the QCA955X SoCs
MIPS: ath79: add PCI controller registration code for the QCA955X SoCs
MIPS: ath79: add WMAC registration code for the QCA955X SoCs
MIPS: ath79: register UART for the QCA955X SoCs
MIPS: ath79: add QCA955X specific glue to ath79_device_reset_{set, clear}
MIPS: ath79: add GPIO setup code for the QCA955X SoCs
MIPS: ath79: add IRQ handling code for the QCA955X SoCs
MIPS: ath79: add clock setup code for the QCA955X SoCs
MIPS: ath79: add SoC detection code for the QCA955X SoCs
MIPS: ath79: add early printk support for the QCA955X SoCs
MIPS: ath79: fix WMAC IRQ resource assignment
mips: reserve elfcorehdr
mips: Make sure kernel memory is in iomem
MIPS: ath79: use dynamically allocated USB platform devices
...
We can't look up the address of the entry point of the function simply
via that function symbol for all architectures.
For PPC64 ABI, actually there is a function descriptors structure.
A function descriptor is a three doubleword data structure that contains
the following values:
* The first doubleword contains the address of the entry point of
the function.
* The second doubleword contains the TOC base address for
the function.
* The third doubleword contains the environment pointer for
languages such as Pascal and PL/1.
So we should call a wapperred dereference_function_descriptor() to get
the address of the entry point of the function.
Note this is also safe for other architecture after refer to
"include/asm-generic/sections.h" since:
dereference_function_descriptor(p) always is (p) if without arched definition.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
ichx_gpio_check_available() returns either 0 or -ENXIO depending on whether
the given GPIO is available or not. However, callers of this function treat
the return value as boolean:
...
if (!ichx_gpio_check_available(gpio, nr))
return -ENXIO;
which erroneusly fails when the GPIO is available and not vice versa.
Fix this by making the function return boolean as expected by the callers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This comment applies to gpio_to_chip(), not gpiod_to_chip().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Constify descriptor parameter of gpiod_* functions for those that
should obviously not modify it. This includes value or direction get,
cansleep, and IRQ number query.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some functions dereferenced their GPIO descriptor argument without
checking its validity first, potentially leading to an oops when given
an invalid argument.
This patch also makes gpio_get_value() more resilient when given an
invalid GPIO, returning 0 instead of silently crashing.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
A simple cache policy that writes back all data to the origin.
This is used to decommission a dm cache by emptying it.
Signed-off-by: Heinz Mauelshagen <mauelshagen@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
A cache policy that uses a multiqueue ordered by recent hit
count to select which blocks should be promoted and demoted.
This is meant to be a general purpose policy. It prioritises
reads over writes.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a target that allows a fast device such as an SSD to be used as a
cache for a slower device such as a disk.
A plug-in architecture was chosen so that the decisions about which data
to migrate and when are delegated to interchangeable tunable policy
modules. The first general purpose module we have developed, called
"mq" (multiqueue), follows in the next patch. Other modules are
under development.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Heinz Mauelshagen <mauelshagen@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch takes advantage of the new bio-prison interface where the
memory is now passed in rather than using a mempool in bio-prison.
This allows the map function to avoid performing potentially-blocking
allocations that could lead to deadlocks: We want to avoid the cell
allocation that is done in bio_detain.
(The potential for mempool deadlocks still remains in other functions
that use bio_detain.)
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change the dm_bio_prison interface so that instead of allocating memory
internally, dm_bio_detain is supplied with a pre-allocated cell each
time it is called.
This enables a subsequent patch to move the allocation of the struct
dm_bio_prison_cell outside the thin target's mapping function so it can
no longer block there.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add dm_btree_walk to iterate through the contents of a btree.
This will be used by the dm cache target.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a num_write_bios function to struct target.
If an instance of a target sets this, it will be queried before the
target's mapping function is called on a write bio, and the response
controls the number of copies of the write bio that the target will
receive.
This provides a convenient way for a target to send the same data to
more than one device. The new cache target uses this in writethrough
mode, to send the data both to the cache and the backing device.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch allows the administrator to reduce the rate at which kcopyd
issues I/O.
Each module that uses kcopyd acquires a throttle parameter that can be
set in /sys/module/*/parameters.
We maintain a history of kcopyd usage by each module in the variables
io_period and total_period in struct dm_kcopyd_throttle. The actual
kcopyd activity is calculated as a percentage of time equal to
"(100 * io_period / total_period)". This is compared with the user-defined
throttle percentage threshold and if it is exceeded, we sleep.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch introduces enhanced message support that allows the
device-mapper core to recognise messages that are common to all devices,
and for messages to return data to userspace.
Core messages are processed by the function "message_for_md". If the
device mapper doesn't support the message, it is passed to the target
driver.
If the message returns data, the kernel sets the flag
DM_MESSAGE_OUT_FLAG.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Device-mapper ioctls receive and send data in a buffer supplied
by userspace. The buffer has two parts. The first part contains
a 'struct dm_ioctl' and has a fixed size. The second part depends
on the ioctl and has a variable size.
This patch recognises the specific ioctls that do not use the variable
part of the buffer and skips allocating memory for it.
In particular, when a device is suspended and a resume ioctl is sent,
this now avoid memory allocation completely.
The variable "struct dm_ioctl tmp" is moved from the function
copy_params to its caller ctl_ioctl and renamed to param_kernel.
It is used directly when the ioctl function doesn't need any arguments.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch introduces flags for each ioctl function.
So far, one flag is defined, IOCTL_FLAGS_NO_PARAMS. It is set if the
function processing the ioctl doesn't take or produce any parameters in
the section of the data buffer that has a variable size.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch merges io_pool and tio_pool into io_pool and cleans up
related functions.
Though device-mapper used to have 2 pools of objects for each dm device,
the use of bioset frontbad for per-bio data has shrunk the number of
pools to 1 for both bio-based and request-based device types.
(See c0820cf5 "dm: introduce per_bio_data" and
94818742 "dm: Use bioset's front_pad for dm_rq_clone_bio_info")
So dm no longer has to maintain 2 different pointers.
No functional changes.
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove _rq_bio_info_cache, which is no longer used.
No functional changes.
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm_calculate_queue_limits will first reset the provided limits to
defaults using blk_set_stacking_limits; whereby defeating the purpose of
retaining the original live table's limits -- as was intended via commit
3ae7065616 ("dm: retain table limits when
swapping to new table with no devices").
Fix this improper limits initialization (in the no data devices case) by
avoiding the call to dm_calculate_queue_limits.
[patch header revised by Mike Snitzer]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v3.6+
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add module aliases so that autoloading works correctly if the user
tries to activate "snapshot-origin" or "snapshot-merge" targets.
Reference: https://bugzilla.redhat.com/889973
Reported-by: Chao Yang <chyang@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mark some constant parameters constant in some dm-btree functions.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename functions involved in splitting and cloning bios.
The sequence of functions is now:
(1) __split_and_process* - entry point that selects the processing strategy
(2) __send* - prepare the details for each bio needed and loop through them
(3) __clone_and_map* - creates a clone and maps it
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use 'bio' in the name of variables and functions that deal with
bios rather than 'request' to avoid confusion with the normal
block layer use of 'request'.
No functional changes.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove the no-longer-used struct bio_set argument from clone_bio and split_bvec.
Use tio->ti in __map_bio() instead of passing in ti.
Factor out some code for setting up cloned bios.
Take target_request_nr as a parameter to alloc_tio().
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use block_size_is_power_of_two() rather than checking
sectors_per_block_shift directly. Also introduce local pool variable in
get_bio_block() to eliminate redundant tc->pool dereferences.
No functional change.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use WRITE_FLUSH instead of REQ_FLUSH for submitted requests to make it
consistent with the rest of the kernel. There is no functional change.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If allocation fails, the local var *t is not used any more after kfree.
Don't need to reset it to NULL. Remove the unnecesary NULL set here.
Signed-off-by: Wang Sheng-Hui <shhuiw@gmail.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Support a non-power-of-2 discard granularity in dm-thin, now that the block
layer supports this(via 8dd2cb7e88 "block:
discard granularity might not be power of 2" and
59771079c1 "blk: avoid divide-by-zero with zero
discard granularity").
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Avoid returning a truncated table or status string instead of setting
the DM_BUFFER_FULL_FLAG when the last target of a table fills the
buffer.
When processing a table or status request, the function retrieve_status
calls ti->type->status. If ti->type->status returns non-zero,
retrieve_status assumes that the buffer overflowed and sets
DM_BUFFER_FULL_FLAG.
However, targets don't return non-zero values from their status method
on overflow. Most targets returns always zero.
If a buffer overflow happens in a target that is not the last in the
table, it gets noticed during the next iteration of the loop in
retrieve_status; but if a buffer overflow happens in the last target, it
goes unnoticed and erroneously truncated data is returned.
In the current code, the targets behave in the following way:
* dm-crypt returns -ENOMEM if there is not enough space to store the
key, but it returns 0 on all other overflows.
* dm-thin returns errors from the status method if a disk error happened.
This is incorrect because retrieve_status doesn't check the error
code, it assumes that all non-zero values mean buffer overflow.
* all the other targets always return 0.
This patch changes the ti->type->status function to return void (because
most targets don't use the return code). Overflow is detected in
retrieve_status: if the status method fills up the remaining space
completely, it is assumed that buffer overflow happened.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch fixes a regression introduced in v3.8, which causes oops
like this when dm-multipath is used:
general protection fault: 0000 [#1] SMP
RIP: 0010:[<ffffffff810fe754>] [<ffffffff810fe754>] mempool_free+0x24/0xb0
Call Trace:
<IRQ>
[<ffffffff81187417>] bio_put+0x97/0xc0
[<ffffffffa02247a5>] end_clone_bio+0x35/0x90 [dm_mod]
[<ffffffff81185efd>] bio_endio+0x1d/0x30
[<ffffffff811f03a3>] req_bio_endio.isra.51+0xa3/0xe0
[<ffffffff811f2f68>] blk_update_request+0x118/0x520
[<ffffffff811f3397>] blk_update_bidi_request+0x27/0xa0
[<ffffffff811f343c>] blk_end_bidi_request+0x2c/0x80
[<ffffffff811f34d0>] blk_end_request+0x10/0x20
[<ffffffffa000b32b>] scsi_io_completion+0xfb/0x6c0 [scsi_mod]
[<ffffffffa000107d>] scsi_finish_command+0xbd/0x120 [scsi_mod]
[<ffffffffa000b12f>] scsi_softirq_done+0x13f/0x160 [scsi_mod]
[<ffffffff811f9fd0>] blk_done_softirq+0x80/0xa0
[<ffffffff81044551>] __do_softirq+0xf1/0x250
[<ffffffff8142ee8c>] call_softirq+0x1c/0x30
[<ffffffff8100420d>] do_softirq+0x8d/0xc0
[<ffffffff81044885>] irq_exit+0xd5/0xe0
[<ffffffff8142f3e3>] do_IRQ+0x63/0xe0
[<ffffffff814257af>] common_interrupt+0x6f/0x6f
<EOI>
[<ffffffffa021737c>] srp_queuecommand+0x8c/0xcb0 [ib_srp]
[<ffffffffa0002f18>] scsi_dispatch_cmd+0x148/0x310 [scsi_mod]
[<ffffffffa000a38e>] scsi_request_fn+0x31e/0x520 [scsi_mod]
[<ffffffff811f1e57>] __blk_run_queue+0x37/0x50
[<ffffffff811f1f69>] blk_delay_work+0x29/0x40
[<ffffffff81059003>] process_one_work+0x1c3/0x5c0
[<ffffffff8105b22e>] worker_thread+0x15e/0x440
[<ffffffff8106164b>] kthread+0xdb/0xe0
[<ffffffff8142db9c>] ret_from_fork+0x7c/0xb0
The regression was introduced by the change
c0820cf5 "dm: introduce per_bio_data", where dm started to replace
bioset during table replacement.
For bio-based dm, it is good because clone bios do not exist during the
table replacement.
For request-based dm, however, (not-yet-mapped) clone bios may stay in
request queue and survive during the table replacement.
So freeing the old bioset could cause the oops in bio_put().
Since the size of front_pad may change only with bio-based dm,
it is not necessary to replace bioset for request-based dm.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix kernel-doc warnings in hsi files:
Warning(include/linux/hsi/hsi.h:136): Excess struct/union/enum/typedef member 'e_handler' description in 'hsi_client'
Warning(include/linux/hsi/hsi.h:136): Excess struct/union/enum/typedef member 'pclaimed' description in 'hsi_client'
Warning(include/linux/hsi/hsi.h:136): Excess struct/union/enum/typedef member 'nb' description in 'hsi_client'
Warning(drivers/hsi/hsi.c:434): No description found for parameter 'handler'
Warning(drivers/hsi/hsi.c:434): Excess function parameter 'cb' description in 'hsi_register_port_event'
Don't document "private:" fields with kernel-doc notation.
If you want to leave them fully documented, that's OK, but
then don't mark them as "private:".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Carlos Chinea <carlos.chinea@nokia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adding an include of linux/mm.h resolves this:
drivers/xen/xenbus/xenbus_client.c: In function ‘xenbus_map_ring_valloc_hvm’:
drivers/xen/xenbus/xenbus_client.c:532:66: error: implicit declaration of function ‘page_to_section’ [-Werror=implicit-function-declaration]
CC: stable@vger.kernel.org
Signed-off-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Unwinding code disables all successfully enabled regulators.
Error is logged for every failed regulator.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SP805 driver is only used by the Spear machines, and uses
writel_relaxed, which is not available on all architectures.
The dependency from CONFIG_ARM avoids compilation problems under
randomconfig when CONFIG_ARM_AMBA is enabled for x86 builds.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Update the code to use devm_* API so that driver
core will manage resources.
Signed-off-by: Kumar, Anil <anilkumar.v@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
this patchset add the timeout-sec property to the following drivers:
orion_wdt, pnx4008_wdt, s3c2410_wdt and at91sam9_wdt.
The at91sam9_wdt is tested on evk-pr3,
the other drivers are compile tested only.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
According to Documentation/watchdog/convert_drivers_to_kernel_api.txt,
remove the file_operations struct, miscdevice, and obsolete includes
Since the at91sam watchdog inherent characteristics, add the watchdog
operations: at91wdt_start, at91wdt_stop and at91wdt_ping.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Like other watchdog drivers, this patch adds new option nowayout
which overwrite WATCHDOG_NOWAYOUT.
Signed-off-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add support for watchdog drivers to initialize/set the timeout field
of the watchdog_device structure. The timeout field is initialised
either with the module timeout parameter value (if valid) or with the
timeout-sec dt property (if valid). If both are invalid the initial
value is unchanged.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The more recent devices have a watchdog timer which could be configured
for over 2 hours and not just 2 seconds like the first generation
devices. For those devices do not use the extra software timer, but
directly program the time into the register. This will automatically be
used if the timer supports more than a minute.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Rename wdt_time to timeout to name it like the other watchdog
driver do it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Rename the methods registered to struct watchdog_ops bcm47xx_wdt_ops in
order to add an other struct watchdog_ops using different ops in the
next patch.
Also rename WDT_MAX_TIME to WDT_SOFTTIMER_MAX.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Instead of accessing the function to set the watchdog timer directly,
register a platform driver the platform could register to use this
watchdog driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert the bcm47xx_wdt.c driver to the new watchdog core api.
The nowayout parameter is now added unconditionally to the module.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use devm_* functions to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Now that the new driver is in place, we can remove the old one.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Replace the existing STMP3xxx driver because it has enough drawbacks
that a rewrite is apropriate. The new driver is designed to use the
watchdog framework which makes it a lot smaller and avoids open coding
the watchdog API again. It also uses now an explicitly exported function
from the RTC driver to set up its registers (the old driver silently
reused the hopefully(!) already remapped RTC registers). Also, this
driver is mach independent, while the old one depends on a mach replaced
by another one a year ago. Since the user interface is still the
standard watchdog API, users don't need to adapt.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This RTC also includes a watchdog timer. Provide an accessor function
for setting the watchdog timeout value which will be picked up by a
watchdog driver. Also register the platform_device for the watchdog here
to get the boot-time dependencies right.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Kernel symbol X86_MRST has been removed from the kernel.
INTEL_SCU_WATCHDOG driver can never be compiled due dependence of X86_MRST
which remained in the drivers/watchdog/Kconfig.
Reported-by: Alexander Shiyan <shc_work@mail.ru>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
...so that it's automatically picked up on relevant platforms.
Tested on Kirkwood-based GuruPlug.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The ath79_wdt driver uses a fixed memory address
currently. Although this is working with each
currently supported SoCs, but this may change
in the future. Additionally, the driver includes
platform specific header files in order to be
able to get the memory base of the watchdog
device.
The patch adds a memory resource to the platform
device, and converts the driver to get the base
address of the watchdog device from that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use the managed version of clk_get. This allows to
simplify the probe/remove functions a bit.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In case of SP5100 or SB7x0 chipsets, the sp5100_tco module writes zero to
reserved bits. The module, however, shouldn't depend on specific default
value, and should perform a read-merge-write operation for the reserved
bits.
This patch makes the sp5100_tco module perform a read-merge-write operation
on all the chipset (sp5100, sb7x0, sb8x0 or later).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43176
Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com>
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
In case of SB800 or later chipset and re-programming MMIO address(*),
sp5100_tco module may read incorrect value of reserved bit, because the module
reads a value from an incorrect I/O address. However, this bug doesn't cause
a problem, because when re-programming MMIO address, by chance the module
writes zero (this is BIOS's default value) to the low three bits of register.
* In most cases, PC with SB8x0 or later chipset doesn't need to re-programming
MMIO address, because such PC can enable AcpiMmio and can use 0xfed80b00 for
watchdog register base address.
This patch fixes this bug.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43176
Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com>
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
this module missed a remove callback in the platform ops.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The device IDs are referenced by the driver and potentially
used beyond the init time, as kbuild correctly warns
about. Remove the __initconst annotation.
Without this patch, building at91_dt_defconfig results in:
WARNING: drivers/watchdog/built-in.o(.data+0x28): Section mismatch in reference from the variable at91wdt_driver to the (unknown reference) .init.rodata:(unknown)
The variable at91wdt_driver references
the (unknown reference) __initconst (unknown)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
DA9055_WATCHDOG (introduced in v3.8) needs to select WATCHDOG_CORE so that it will
build cleanly. Fixes these build errors:
da9055_wdt.c:(.text+0xe9bc7): undefined reference to `watchdog_unregister_device'
da9055_wdt.c:(.text+0xe9f4b): undefined reference to `watchdog_register_device'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: stable <stable@vger.kernel.org>
This fixes an inconsistent behavior between list_voltage() and get_voltage()
because current implementation of get_voltage() does not check the case
IS_UNSUP() is true.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Number of voltages for SMPS regulators was off by one.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Ian Lartey <ian@slimlogic.co.uk>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Even in failed case of pm_runtime_get_sync, the usage_count
is incremented. In order to keep the usage_count with correct
value and runtime power management to behave correctly, call
pm_runtime_put(_sync) in such case.
Signed-off-by Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Li Fei <fei.li@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit f59c8f9f (regulator: core: Support bypass mode)
has a short documentation error around the regulator_allow_bypass
parameter 'enable' which is documented as 'allow'.
This generates kernel-doc warning as follows:
./scripts/kernel-doc drivers/regulator/core.c >/dev/null
Warning(drivers/regulator/core.c:2841): No description found for parameter 'enable'
Warning(drivers/regulator/core.c:2841): Excess function parameter 'allow' description in 'regulator_allow_bypass'
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull EDAC fixes and ghes-edac from Mauro Carvalho Chehab:
"For:
- Some fixes at edac drivers (i7core_edac, sb_edac, i3200_edac);
- error injection support for i5100, when EDAC debug is enabled;
- fix edac when it is loaded builtin (early init for the subsystem);
- a "Firmware First" EDAC driver, allowing ghes to report errors via
EDAC (ghes-edac).
With regards to ghes-edac, this fixes a longstanding BZ at Red Hat
that happens with Nehalem and Sandy Bridge CPUs: when both GHES and
i7core_edac or sb_edac are running, the error reports are
unpredictable, as both BIOS and OS race to access the registers. With
ghes-edac, the EDAC core will refuse to register any other concurrent
memory error driver.
This patchset moves the ghes struct definitions to a separate header
file (include/acpi/ghes.h) and adds 3 hooks at apei/ghes.c to
register/unregister and to report errors via ghes-edac. Those changes
were acked by ghes driver maintainer (Huang)."
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: (30 commits)
i5100_edac: convert to use simple_open()
ghes_edac: fix to use list_for_each_entry_safe() when delete list items
ghes_edac: Fix RAS tracing
ghes_edac: Make it compliant with UEFI spec 2.3.1
ghes_edac: Improve driver's printk messages
ghes_edac: Don't credit the same memory dimm twice
ghes_edac: do a better job of filling EDAC DIMM info
ghes_edac: add support for reporting errors via EDAC
ghes_edac: Register at EDAC core the BIOS report
ghes: add the needed hooks for EDAC error report
ghes: move structures/enum to a header file
edac: add support for error type "Info"
edac: add support for raw error reports
edac: reduce stack pressure by using a pre-allocated buffer
edac: lock module owner to avoid error report conflicts
edac: remove proc_name from mci structure
edac: add a new memory layer type
edac: initialize the core earlier
edac: better report error conditions in debug mode
i5100_edac: Remove two checkpatch warnings
...
The new intel_powerclamp thermal cooling device driver was merged in
commit 2af78448ff (Pull thermal management updates from Zhang Rui)
without any data conflicts. But there was a more subtle conflict I
missed: the driver uses MAX_USER_RT_PRIO, but commit 8bd75c77b7
("sched/rt: Move rt specific bits into new header file") had moved that
define from <linux/sched.h> to <linux/sched/rt.h>.
Which caused this build failure:
drivers/thermal/intel_powerclamp.c: In function ‘clamp_thread’:
drivers/thermal/intel_powerclamp.c:360:21: error: ‘MAX_USER_RT_PRIO’ undeclared (first use in this function)
drivers/thermal/intel_powerclamp.c:360:21: note: each undeclared identifier is reported only once for each function it appears in
And because I don't do a full "make allmodconfig" build after each pull,
I didn't notice until too late. So now the fix is here, separately from
the merge commit.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This series contains changes for the Marvell EBU platforms (mvebu,
orion, kirkwood, dove) that were not part of the first set of pull
requests because of dependencies on the MMC tree, and being submitted
a little late.
Notable changes are:
* More devices get moved out of board files into device tree
descriptions. The remaining devices listed in there have patches
that will get sent for 3.10, after which we can remove a lot of the
board files entirely. We are doing the pinctrl and mmc drivers here,
ethernet and PCI still remain.
* SMP support for mvebu is improved with support for the
local interrupt controller.
* The Guruplug board file gets replaced with a DT description.
Unfortunately, the dependency on the MMC tree turned out to be a much
larger problem than expected, when the MMC maintainer rebased the patches
in his tree that all of the patches in this branch are based on, which
caused merge conflicts between the new and old versions of those patches.
To work around the merge conflicts, this branch rebases all patches
on top of the respective MMC patches that did get merged into 3.9.
The patches are all identical to the versions that were part of
linux-next, but have a new commit date.
Merge conflicts:
* in board-nsa310.c, the gpio.h inclusion was removed prematurely and
put back as a bug fix earlier. With this series it is really not needed
any more.
* The patch to add rtc support was already applied by Andrew Morton,
and conflicts with a second copy that was in this series, which adds
a lot of other devices to arch/arm/boot/dts/armada-370-xp.dtsi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7l0+
-----END PGP SIGNATURE-----
Merge tag 'late-mvebu-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC mvebu platform changes from Olof Johansson:
"This series contains changes for the Marvell EBU platforms (mvebu,
orion, kirkwood, dove) that were not part of the first set of pull
requests because of dependencies on the MMC tree, and being submitted
a little late.
Notable changes are:
- More devices get moved out of board files into device tree
descriptions. The remaining devices listed in there have patches
that will get sent for 3.10, after which we can remove a lot of the
board files entirely. We are doing the pinctrl and mmc drivers
here, ethernet and PCI still remain.
- SMP support for mvebu is improved with support for the local
interrupt controller.
- The Guruplug board file gets replaced with a DT description.
Unfortunately, the dependency on the MMC tree turned out to be a much
larger problem than expected, when the MMC maintainer rebased the
patches in his tree that all of the patches in this branch are based
on, which caused merge conflicts between the new and old versions of
those patches.
To work around the merge conflicts, this branch rebases all patches on
top of the respective MMC patches that did get merged into 3.9. The
patches are all identical to the versions that were part of
linux-next, but have a new commit date."
* tag 'late-mvebu-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (90 commits)
arm: mvebu: enable the SD card slot on Armada 370 Reference Design board
ARM: kirkwood: topkick: init mvsdio via DT
ARM: kirkwood: nsa310: convert to pinctrl
ARM: Kirkwood: topkick: Enable i2c bus.
ARM: kirkwood: topkick: convert to pinctrl
ARM: dove: convert serial DT nodes to clocks property
arm: mvebu: Add SPI flash on Armada 370 DB board
arm: mvebu: Add SPI flash on Armada XP-DB board
arm: mvebu: Add SPI flash on Armada XP-GP board
arm: mvebu: Add support for SPI controller in Armada 370/XP
clocksource: update and move armada-370-xp-timer documentation to timer directory
arm: mvebu: update DT to support local timers
ARM: Dove: convert usb host controller to DT
arm: mvebu: Enable USB controllers on Armada 370/XP boards
arm: mvebu: Add support for USB host controllers in Armada 370/XP
arm: mvebu: add button for OpenBlocks AX3-4
ARM: Kirkwood: Convert NS2 to gpio-poweroff.
ARM: Kirkwood: Convert NSA310 I2C to device tree
ARM: Kirkwood: Convert NSA310 to use gpio-poweroff driver
ARM: Kirkwood: Convert NSA310 to DT based regulators.
...
This branch contains changes for OMAP that came in late during the release
staging, close to when the merge window opened.
It contains, among other things:
- OMAP PM fixes and some patches for audio device integration
- OMAP clock fixes related to common clock conversion
- A set of patches cleaning up WFI entry and blocking.
- A set of fixes and IP block support for PM on TI AM33xx SoCs (Beaglebone, etc)
- A set of smaller fixes and cleanups around AM33xx restart and revision
detection, as well as removal of some dead code (CONFIG_32K_TIMER_HZ)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/vBT
-----END PGP SIGNATURE-----
Merge tag 'late-omap' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late OMAP changes from Olof Johansson:
"This branch contains changes for OMAP that came in late during the
release staging, close to when the merge window opened.
It contains, among other things:
- OMAP PM fixes and some patches for audio device integration
- OMAP clock fixes related to common clock conversion
- A set of patches cleaning up WFI entry and blocking.
- A set of fixes and IP block support for PM on TI AM33xx SoCs
(Beaglebone, etc)
- A set of smaller fixes and cleanups around AM33xx restart and
revision detection, as well as removal of some dead code
(CONFIG_32K_TIMER_HZ)"
* tag 'late-omap' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: omap2: include linux/errno.h in hwmod_reset
ARM: OMAP2+: fix some omap_device_build() calls that aren't compiled by default
ARM: OMAP4: hwmod data: Enable AESS hwmod device
ARM: OMAP4: hwmod data: Update AESS data with memory bank area
ARM: OMAP4+: AESS: enable internal auto-gating during initial setup
ASoC: TI AESS: add autogating-enable function, callable from architecture code
ARM: OMAP2+: hwmod: add enable_preprogram hook
ARM: OMAP4: clock data: Add missing clkdm association for dpll_usb
ARM: OMAP2+: PM: Fix the dt return condition in pm_late_init()
ARM: OMAP2: am33xx-hwmod: Fix "register offset NULL check" bug
ARM: OMAP2+: AM33xx: hwmod: add missing HWMOD_NO_IDLEST flags
ARM: OMAP: AM33xx hwmod: Add parent-child relationship for PWM subsystem
ARM: OMAP: AM33xx hwmod: Corrects PWM subsystem HWMOD entries
ARM: DTS: AM33XX: Add nodes for OCMC RAM and WKUP-M3
ARM: OMAP2+: AM33XX: Update the hardreset API
ARM: OMAP2+: AM33XX: hwmod: Update the WKUP-M3 hwmod with reset status bit
ARM: OMAP2+: AM33XX: hwmod: Fixup cpgmac0 hwmod entry
ARM: OMAP2+: AM33XX: hwmod: Update TPTC0 hwmod with the right flags
ARM: OMAP2+: AM33XX: hwmod: Register OCMC RAM hwmod
ARM: OMAP2+: AM33XX: CM/PRM: Use __ASSEMBLER__ macros in header files
...
This branch contains of devicetree changes for the Freescale i.MX platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process since
every line of the file is touched.
On top of that are a handful of the regular changes; enabling more boards
as DT-based instead of legacy board files (mx25pdk), enabling another
driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other platforms
in the future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=72aL
-----END PGP SIGNATURE-----
Merge tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC i.MX DT changes from Olof Johansson:
"This branch contains of devicetree changes for the Freescale i.MX
platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process
since every line of the file is touched.
On top of that are a handful of the regular changes; enabling more
boards as DT-based instead of legacy board files (mx25pdk), enabling
another driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other
platforms in the future."
* tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: dts: add dtsi for imx6q and imx6dl
ARM: dts: rename imx6q.dtsi to imx6qdl.dtsi
ARM: dts: i.MX6: Add regulator delay support
ARM: dts: Add device tree entry for onewire master on i.MX53
ARM: i.MX53: Add clocks for i.mx53 onewire master.
W1: Add device tree support to MXC onewire master.
ARM: imx: enable imx6q-cpufreq support
ARM: dts: Add apf51 basic support
ARM i.MX6: change mxs usbphy clock usage
ARM: dts: imx6q: Remove silicon version from SDMA firmware
ARM i.MX53: dts: add oftree for MBa53 baseboard
ARM i.MX53: add dts for the TQ tqma53 module
ARM: dts: imx53: pinctrl update
ARM i.MX51 babbage: Add keypad support
ARM: dts: imx: Add imx51 KPP entry
ARM: dts: imx25-karo-tx25: Put status entry in the end
ARM: mx25pdk: Add device tree support
ARM: dts: imx: use nodes label in board dts
ARM: dts: add missing imx dtb targets
ARM: boot: dts: Add an entry for imx27-pdk.dtb
...
Pull thermal management updates from Zhang Rui:
"Highlights:
- introduction of Dove thermal sensor driver.
- introduction of Kirkwood thermal sensor driver.
- introduction of intel_powerclamp thermal cooling device driver.
- add interrupt and DT support for rcar thermal driver.
- add thermal emulation support which allows platform thermal driver
to do software/hardware emulation for thermal issues."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (36 commits)
thermal: rcar: remove __devinitconst
thermal: return an error on failure to register thermal class
Thermal: rename thermal governor Kconfig option to avoid generic naming
thermal: exynos: Use the new thermal trend type for quick cooling action.
Thermal: exynos: Add support for temperature falling interrupt.
Thermal: Dove: Add Themal sensor support for Dove.
thermal: Add support for the thermal sensor on Kirkwood SoCs
thermal: rcar: add Device Tree support
thermal: rcar: remove machine_power_off() from rcar_thermal_notify()
thermal: rcar: add interrupt support
thermal: rcar: add read/write functions for common/priv data
thermal: rcar: multi channel support
thermal: rcar: use mutex lock instead of spin lock
thermal: rcar: enable CPCTL to use hardware TSC deciding
thermal: rcar: use parenthesis on macro
Thermal: fix a build warning when CONFIG_THERMAL_EMULATION cleared
Thermal: fix a wrong comment
thermal: sysfs: Add a new sysfs node emul_temp for thermal emulation
PM: intel_powerclamp: off by one in start_power_clamp()
thermal: exynos: Miscellaneous fixes to support falling threshold interrupt
...
Pull Ceph updates from Sage Weil:
"A few groups of patches here. Alex has been hard at work improving
the RBD code, layout groundwork for understanding the new formats and
doing layering. Most of the infrastructure is now in place for the
final bits that will come with the next window.
There are a few changes to the data layout. Jim Schutt's patch fixes
some non-ideal CRUSH behavior, and a set of patches from me updates
the client to speak a newer version of the protocol and implement an
improved hashing strategy across storage nodes (when the server side
supports it too).
A pair of patches from Sam Lang fix the atomicity of open+create
operations. Several patches from Yan, Zheng fix various mds/client
issues that turned up during multi-mds torture tests.
A final set of patches expose file layouts via virtual xattrs, and
allow the policies to be set on directories via xattrs as well
(avoiding the awkward ioctl interface and providing a consistent
interface for both kernel mount and ceph-fuse users)."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (143 commits)
libceph: add support for HASHPSPOOL pool flag
libceph: update osd request/reply encoding
libceph: calculate placement based on the internal data types
ceph: update support for PGID64, PGPOOL3, OSDENC protocol features
ceph: update "ceph_features.h"
libceph: decode into cpu-native ceph_pg type
libceph: rename ceph_pg -> ceph_pg_v1
rbd: pass length, not op for osd completions
rbd: move rbd_osd_trivial_callback()
libceph: use a do..while loop in con_work()
libceph: use a flag to indicate a fault has occurred
libceph: separate non-locked fault handling
libceph: encapsulate connection backoff
libceph: eliminate sparse warnings
ceph: eliminate sparse warnings in fs code
rbd: eliminate sparse warnings
libceph: define connection flag helpers
rbd: normalize dout() calls
rbd: barriers are hard
rbd: ignore zero-length requests
...
Pull block driver bits from Jens Axboe:
"After the block IO core bits are in, please grab the driver updates
from below as well. It contains:
- Fix ancient regression in dac960. Nobody must be using that
anymore...
- Some good fixes from Guo Ghao for loop, fixing both potential
oopses and deadlocks.
- Improve mtip32xx for NUMA systems, by being a bit more clever in
distributing work.
- Add IBM RamSan 70/80 driver. A second round of fixes for that is
pending, that will come in through for-linus during the 3.9 cycle
as per usual.
- A few xen-blk{back,front} fixes from Konrad and Roger.
- Other minor fixes and improvements."
* 'for-3.9/drivers' of git://git.kernel.dk/linux-block:
loopdev: ignore negative offset when calculate loop device size
loopdev: remove an user triggerable oops
loopdev: move common code into loop_figure_size()
loopdev: update block device size in loop_set_status()
loopdev: fix a deadlock
xen-blkback: use balloon pages for persistent grants
xen-blkfront: drop the use of llist_for_each_entry_safe
xen/blkback: Don't trust the handle from the frontend.
xen-blkback: do not leak mode property
block: IBM RamSan 70/80 driver fixes
rsxx: add slab.h include to dma.c
drivers/block/mtip32xx: add missing GENERIC_HARDIRQS dependency
block: remove new __devinit/exit annotations on ramsam driver
block: IBM RamSan 70/80 device driver
drivers/block/mtip32xx/mtip32xx.c:1726:5: sparse: symbol 'mtip_send_trim' was not declared. Should it be static?
drivers/block/mtip32xx/mtip32xx.c:4029:1: sparse: symbol 'mtip_workq_sdbf0' was not declared. Should it be static?
dac960: return success instead of -ENOTTY
mtip32xx: add trim support
mtip32xx: Add workqueue and NUMA support
block: delete super ancient PC-XT driver for 1980's hardware
