We cannot restart recovery. Once we begin to recover a node, keep the state
of the recovery intact and follow through, regardless of any other node
deaths that may occur.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
If the previous master of the recovery lock dies, let calc_usage take it
down completely and let the caller completely redo the dlmlock() call.
Otherwise, there will never be an opportunity to re-master the lockres and
recovery wont be able to progress.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Use the existing structure for blocking migrations when ASTs are pending to
achieve the same result. If we can catch the assert before it goes on the
wire, just cancel it and let the migration continue.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Now we never change the owner of a lock resource until unmount or node
death. This will be re-enabled once some issues in the algorithm used have
been resolved.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
In dlmlock_remote(), do not call purge_lockres until the lock resource
actually changes. otherwise, the mastery info on the lockres will go away
underneath the caller.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
When mastering non-recovery lock resources, additional time was frequently
needed to allow the disk heartbeat to catch up with the network timeout. the
recovery lock resource is time critical and avoids this path.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Recovery will spin in dlm_pre_master_reco_lockres if we do not ignore
timed-out network responses from dead nodes.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Change behavior of dlm_restart_lock_mastery() when a node goes down. Dump
all responses that have been collected and start over.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
This is an error on the sending side, so gracefully error out on the
receiving end.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Immediately purge a lockress that the local node is not the master of.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Makes it easier for the recovery process to deal with node death.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Take a reference on lockres structures while they are on the recovery list.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
handle errors during lock assert master by either killing self or other node
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
The check for an empty lvb should check the entire buffer not just the first
byte.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Recovery may have happened and it may now be mastered locally.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
The OCFS2 DLM allocates a number of pages for a hash to lookup locks.
There was a bug where a PAGE_SIZE bigger than the hash size (eg, 64K
pages) would result in zero pages allocated.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
This allows us to have a hash table greater than a single page which greatly
improves dlm performance on some tests.
Signed-off-by: Daniel Phillips <phillips@google.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Gains us a bit of performance on loads which heavily hit the lockres hash.
Patch suggested by Daniel Phillips <phillips@google.com>.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
typo fixes
Clean up 'inline is not at beginning' warnings for usb storage
Storage class should be first
i386: Trivial typo fixes
ixj: make ixj_set_tone_off() static
spelling fixes
fix paniced->panicked typos
Spelling fixes for Documentation/atomic_ops.txt
move acknowledgment for Mark Adler to CREDITS
remove the bouncing email address of David Campbell
The changes in the tty handling contain a bug while accessing
the last byte in the skb. Since special sequence for control of
DTMF and FAX via ttyI* devices handled via this path, these services
do not work anymore.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was spotted by coverity #id 1300. Since the array has only four
elements, we should just use those four.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit c7b2eff059.
Hugh Dickins explains:
"It seems too little tested: "losetup -d /dev/loop0" fails with
EINVAL because nothing sets lo_thread; but even when you patch
loop_thread() to set lo->lo_thread = current, it can't survive
more than a few dozen iterations of the loop below (with a tmpfs
mounted on /tst):
j=0
cp /dev/zero /tst
while :
do
let j=j+1
echo "Doing pass $j"
losetup /dev/loop0 /tst/zero
mkfs -t ext2 -b 1024 /dev/loop0 >/dev/null 2>&1
mount -t ext2 /dev/loop0 /mnt
umount /mnt
losetup -d /dev/loop0
done
it collapses with failed ioctl then BUG_ON(!bio).
I think the original lo_done completion was more subtle and safe
than the kthread conversion has allowed for."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
