[ Upstream commit 3cad8f9115 ]
Currently, proc_cmd is used to dispatch command to 'pg_ctrl', 'pg_thread',
'pg_set'. proc_cmd is designed to check command result with grep the
"Result:", but this might fail since this string is only shown in
'pg_thread' and 'pg_set'.
This commit fixes this logic by grep-ing the "Result:" string only when
the command is not for 'pg_ctrl'.
For clarity of an execution flow, 'errexit' flag has been set.
To cleanup pktgen on exit, trap has been added for EXIT signal.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bee447e224 ]
The DDC/CI protocol involves sending a multi-byte request to the
display via I2C, which is typically followed by a multi-byte
response. The internal I2C controller only allows single byte
reads/writes or reads of 8 sequential bytes, hence DDC/CI is not
supported when the internal I2C controller is used. The I2C
transfers complete without errors, however the data in the response
is garbage. Abort transfers to/from slave address 0x37 (DDC) with
-EOPNOTSUPP, to make it evident that the communication is failing.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sean Paul <sean@poorly.run>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002124354.v2.1.I709dfec496f5f0b44a7b61dcd4937924da8d8382@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e84a18a25 ]
When probed after the HDMI notifier, calling cec_notifier_cec_adap_register()
calls the enable() adapter callback, but the HW is not yet set up.
Moving cec_notifier_cec_adap_register() right before cec_register_adapter()
fixes the following crash:
Ignoring spurious kernel translation fault at virtual address 0000000000000008
[...]
Hardware name: Khadas VIM (DT)
[...]
pc : __do_kernel_fault+0xdc/0x120
lr : __do_kernel_fault+0xdc/0x120
[...]
Call trace:
__do_kernel_fault+0xdc/0x120
do_page_fault+0x180/0x458
do_translation_fault+0x64/0x70
do_mem_abort+0x3c/0x98
el1_da+0x20/0x94
meson_ao_cec_adap_enable+0x30/0x218 [ao_cec]
__cec_s_phys_addr+0x184/0x270
cec_s_phys_addr+0x44/0x60
cec_notifier_cec_adap_register+0x68/0x90
meson_ao_cec_probe+0xb0/0x288 [ao_cec]
[...]
el0_svc_compat+0x8/0x10
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 20958f9d5c ("media: meson/ao-cec: use cec_notifier_cec_adap_(un)register")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b211f9c5a ]
The CEC_MSG_GIVE_DECK_STATUS and CEC_MSG_GIVE_TUNER_DEVICE_STATUS commands
both have a status_req argument: ON, OFF, ONCE. If ON or ONCE, then the
follower will reply with a STATUS message. Either once or whenever the
status changes (status_req == ON).
If status_req == OFF, then it will stop sending continuous status updates,
but the follower will *not* send a STATUS message in that case.
This means that if status_req == OFF, then msg->reply should be 0 as well
since no reply is expected in that case.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 649cd16c43 ]
If usb_set_interface() failed, iface->cur_altsetting will
not be assigned and it will be used in flexcop_usb_transfer_init()
It may lead a NULL pointer dereference.
Check usb_set_interface() return value in flexcop_usb_init()
and return failed to avoid using this NULL pointer.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit daebf24a8e ]
Currently the Linux Kernel Memory Model gives an incorrect response
for the following litmus test:
C plain-WWC
{}
P0(int *x)
{
WRITE_ONCE(*x, 2);
}
P1(int *x, int *y)
{
int r1;
int r2;
int r3;
r1 = READ_ONCE(*x);
if (r1 == 2) {
smp_rmb();
r2 = *x;
}
smp_rmb();
r3 = READ_ONCE(*x);
WRITE_ONCE(*y, r3 - 1);
}
P2(int *x, int *y)
{
int r4;
r4 = READ_ONCE(*y);
if (r4 > 0)
WRITE_ONCE(*x, 1);
}
exists (x=2 /\ 1:r2=2 /\ 2:r4=1)
The memory model says that the plain read of *x in P1 races with the
WRITE_ONCE(*x) in P2.
The problem is that we have a write W and a read R related by neither
fre or rfe, but rather W ->coe W' ->rfe R, where W' is an intermediate
write (the WRITE_ONCE() in P0). In this situation there is no
particular ordering between W and R, so either a wr-vis link from W to
R or an rw-xbstar link from R to W would prove that the accesses
aren't concurrent.
But the LKMM only looks for a wr-vis link, which is equivalent to
assuming that W must execute before R. This is not necessarily true
on non-multicopy-atomic systems, as the WWC pattern demonstrates.
This patch changes the LKMM to accept either a wr-vis or a reverse
rw-xbstar link as a proof of non-concurrency.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Andrea Parri <parri.andrea@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 472b39c3d1 ]
Inside function max8907_regulator_probe(), variable val could
be uninitialized if regmap_read() fails. However, val is used
later in the if statement to decide the content written to
"pmic", which is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Link: https://lore.kernel.org/r/20191003175813.16415-1-yzhai003@ucr.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaecce12f5 ]
When unloading omap3-rom-rng, we'll get the following:
WARNING: CPU: 0 PID: 100 at drivers/clk/clk.c:948 clk_core_disable
This is because the clock may be already disabled by omap3_rom_rng_idle().
Let's fix the issue by checking for rng_idle on exit.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes: 1c6b7c2108 ("hwrng: OMAP3 ROM Random Number Generator support")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2eb2d198bd ]
The next version of Clang will start policing compiler command line
options, and will reject combinations of -march and -mfpu that it
thinks are incompatible.
This results in errors like
clang-10: warning: ignoring extension 'crypto' because the 'armv7-a'
architecture does not support it [-Winvalid-command-line-argument]
/tmp/aegis128-neon-inner-5ee428.s: Assembler messages:
/tmp/aegis128-neon-inner-5ee428.s:73: Error: selected
processor does not support `aese.8 q2,q14' in ARM mode
when buiding the SIMD aegis128 code for 32-bit ARM, given that the
'armv7-a' -march argument is considered to be compatible with the
ARM crypto extensions. Instead, we should use armv8-a, which does
allow the crypto extensions to be enabled.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39abcc8484 ]
When R-Car Gen3 USB 2.0 is in Gadget mode, if host is detached an interrupt
will be generated and Suspended state bit is set in interrupt status
register. Interrupt handler will call driver->suspend(composite_suspend)
if suspended state bit is set. composite_suspend will call
ffs_func_suspend which will post FUNCTIONFS_SUSPEND and will be consumed
by user space application via /dev/ep0.
To be able to detect host detach, extend the DVSQ_MASK to cover the
Suspended bit of the DVSQ[2:0] bitfield from the Interrupt Status
Register 0 (INTSTS0) register and perform appropriate action in the
DVST interrupt handler (usbhsg_irq_dev_state).
Without this commit, disconnection of the phone from R-Car-H3 ES2.0
Salvator-X CN9 port is not recognized and reverse role switch does
not happen. If phone is connected again it does not enumerate.
With this commit, disconnection will be recognized and reverse role
switch will happen by a user space application. If phone is connected
again it will enumerate properly and will become visible in the output
of 'lsusb'.
Signed-off-by: Veeraiyan Chidambaram <veeraiyan.chidambaram@in.bosch.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1568207756-22325-3-git-send-email-external.veeraiyan.c@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f5bb7ff8b ]
8822C is a 2x2 11ac chip, and then NSS must be less or equal to 2. However,
current nss of hw cap is 3, likes
hw cap: hci=0x0f, bw=0x07, ptcl=0x03, ant_num=7, nss=3
This commit adds constraint to make sure NSS <= rf_path_num, and result
looks like
hw cap: hci=0x0f, bw=0x07, ptcl=0x03, ant_num=7, nss=2
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8dbebb2bd0 ]
Failure to suspend (venus_suspend_3xx) happens when the system
is fresh booted and loading venus driver. This happens once and
after reload the venus driver modules the problem disrepair.
Fix the failure by skipping the check for WFI and IDLE bits if
PC_READY is on in control status register.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ad0cdf9e2 ]
[Why]
A lot of the time, the backlight characteristic curve maps min backlight
to a non-zero value.
But there are cases where we want the curve to intersect at 0.
In this scenario even if OS never asks to set 0% backlight, the ABM
reduction can result in backlight being lowered close to 0.
This particularly can cause problems in some LED drivers, and in
general just looks like backlight is completely off.
[How]
Add default cap to disallow backlight from dropping below 1%
even after ABM reduction is applied.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c588146378 ]
The "path" buf is supposed to contain path + printf msg up to 24 bytes.
It will be cut anyway, but compiler generates truncation warns like:
"
samples/bpf/../../tools/testing/selftests/bpf/cgroup_helpers.c: In
function ‘setup_cgroup_environment’:
samples/bpf/../../tools/testing/selftests/bpf/cgroup_helpers.c:52:34:
warning: ‘/cgroup.controllers’ directive output may be truncated
writing 19 bytes into a region of size between 1 and 4097
[-Wformat-truncation=]
snprintf(path, sizeof(path), "%s/cgroup.controllers", cgroup_path);
^~~~~~~~~~~~~~~~~~~
samples/bpf/../../tools/testing/selftests/bpf/cgroup_helpers.c:52:2:
note: ‘snprintf’ output between 20 and 4116 bytes into a destination
of size 4097
snprintf(path, sizeof(path), "%s/cgroup.controllers", cgroup_path);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
samples/bpf/../../tools/testing/selftests/bpf/cgroup_helpers.c:72:34:
warning: ‘/cgroup.subtree_control’ directive output may be truncated
writing 23 bytes into a region of size between 1 and 4097
[-Wformat-truncation=]
snprintf(path, sizeof(path), "%s/cgroup.subtree_control",
^~~~~~~~~~~~~~~~~~~~~~~
cgroup_path);
samples/bpf/../../tools/testing/selftests/bpf/cgroup_helpers.c:72:2:
note: ‘snprintf’ output between 24 and 4120 bytes into a destination
of size 4097
snprintf(path, sizeof(path), "%s/cgroup.subtree_control",
cgroup_path);
"
In order to avoid warns, lets decrease buf size for cgroup workdir on
24 bytes with assumption to include also "/cgroup.subtree_control" to
the address. The cut will never happen anyway.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20191002120404.26962-3-ivan.khoronzhuk@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 068ad870bb ]
Changes to function "smu_suspend" in amdgpu_smu.c is a workaround.
We should get real information about if baco is enabled or not, while we
always consider APU SMU feature as enabled in current code.
I know APU do not support baco mode for GPU reset, so I use
"adev->flags" to skip function "smu_feature_is_enabled".
Signed-off-by: chen gong <curry.gong@amd.com>
Reviewed-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6b44ce192 ]
The new __must_check annotation on __copy_from_user() successfully
identified some code that has lacked the check since at least
linux-2.1.73:
arch/x86/math-emu/reg_ld_str.c:88:2: error: ignoring return value of \
function declared with 'warn_unused_result' attribute [-Werror,-Wunused-result]
__copy_from_user(sti_ptr, s, 10);
^~~~~~~~~~~~~~~~ ~~~~~~~~~~~~~~
arch/x86/math-emu/reg_ld_str.c:1129:2: error: ignoring return value of \
function declared with 'warn_unused_result' attribute [-Werror,-Wunused-result]
__copy_from_user(register_base + offset, s, other);
^~~~~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/x86/math-emu/reg_ld_str.c:1131:3: error: ignoring return value of \
function declared with 'warn_unused_result' attribute [-Werror,-Wunused-result]
__copy_from_user(register_base, s + other, offset);
^~~~~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In addition, the get_user()/put_user() helpers do not enforce a return
value check, but actually still require one. These have been missing for
even longer.
Change the internal wrappers around get_user()/put_user() to force
a signal and add a corresponding wrapper around __copy_from_user()
to check all such cases.
[ bp: Break long lines. ]
Fixes: 257e458057e5 ("Import 2.1.73")
Fixes: 9dd819a151 ("uaccess: add missing __must_check attributes")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Bill Metzenthen <billm@melbpc.org.au>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191001142344.1274185-1-arnd@arndb.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81de29d842 ]
alloc_workqueue is not checked for errors and as a result,
a potential NULL dereference could occur.
v2 (Felix Kuehling):
* Fix compile error (kfifo_free instead of fifo_free)
* Return proper error code
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ac6269968 ]
The LCD timing definitions between Linux DRM vs Allwinner are different,
below diagram shows this clear differences.
Active Front Sync Back
Region Porch Porch
<-----------------------><----------------><--------------><-------------->
//////////////////////|
////////////////////// |
////////////////////// |.................. ................
________________
<----- [hv]display ----->
<------------- [hv]sync_start ------------>
<--------------------- [hv]sync_end ---------------------->
<-------------------------------- [hv]total ------------------------------>
<----- lcd_[xy] --------> <- lcd_[hv]spw ->
<---------- lcd_[hv]bp --------->
<-------------------------------- lcd_[hv]t ------------------------------>
The DSI driver misinterpreted the hbp term from the BSP code to refer
only to the backporch, when in fact it was backporch + sync. Thus the
driver incorrectly used the horizontal front porch plus sync in its
calculation of the DRQ set bit value, when it should not have included
the sync timing.
Including additional sync timings leads to flip_done timed out as:
WARNING: CPU: 0 PID: 31 at drivers/gpu/drm/drm_atomic_helper.c:1429 drm_atomic_helper_wait_for_vblanks.part.1+0x298/0x2a0
[CRTC:46:crtc-0] vblank wait timed out
Modules linked in:
CPU: 0 PID: 31 Comm: kworker/0:1 Not tainted 5.1.0-next-20190514-00026-g01f0c75b902d-dirty #13
Hardware name: Allwinner sun8i Family
Workqueue: events deferred_probe_work_func
[<c010ed54>] (unwind_backtrace) from [<c010b76c>] (show_stack+0x10/0x14)
[<c010b76c>] (show_stack) from [<c0688c70>] (dump_stack+0x84/0x98)
[<c0688c70>] (dump_stack) from [<c011d9e4>] (__warn+0xfc/0x114)
[<c011d9e4>] (__warn) from [<c011da40>] (warn_slowpath_fmt+0x44/0x68)
[<c011da40>] (warn_slowpath_fmt) from [<c040cd50>] (drm_atomic_helper_wait_for_vblanks.part.1+0x298/0x2a0)
[<c040cd50>] (drm_atomic_helper_wait_for_vblanks.part.1) from [<c040e694>] (drm_atomic_helper_commit_tail_rpm+0x5c/0x6c)
[<c040e694>] (drm_atomic_helper_commit_tail_rpm) from [<c040e4dc>] (commit_tail+0x40/0x6c)
[<c040e4dc>] (commit_tail) from [<c040e5cc>] (drm_atomic_helper_commit+0xbc/0x128)
[<c040e5cc>] (drm_atomic_helper_commit) from [<c0411b64>] (restore_fbdev_mode_atomic+0x1cc/0x1dc)
[<c0411b64>] (restore_fbdev_mode_atomic) from [<c04156f8>] (drm_fb_helper_restore_fbdev_mode_unlocked+0x54/0xa0)
[<c04156f8>] (drm_fb_helper_restore_fbdev_mode_unlocked) from [<c0415774>] (drm_fb_helper_set_par+0x30/0x54)
[<c0415774>] (drm_fb_helper_set_par) from [<c03ad450>] (fbcon_init+0x560/0x5ac)
[<c03ad450>] (fbcon_init) from [<c03eb8a0>] (visual_init+0xbc/0x104)
[<c03eb8a0>] (visual_init) from [<c03ed1b8>] (do_bind_con_driver+0x1b0/0x390)
[<c03ed1b8>] (do_bind_con_driver) from [<c03ed780>] (do_take_over_console+0x13c/0x1c4)
[<c03ed780>] (do_take_over_console) from [<c03ad800>] (do_fbcon_takeover+0x74/0xcc)
[<c03ad800>] (do_fbcon_takeover) from [<c013c9c8>] (notifier_call_chain+0x44/0x84)
[<c013c9c8>] (notifier_call_chain) from [<c013cd20>] (__blocking_notifier_call_chain+0x48/0x60)
[<c013cd20>] (__blocking_notifier_call_chain) from [<c013cd50>] (blocking_notifier_call_chain+0x18/0x20)
[<c013cd50>] (blocking_notifier_call_chain) from [<c03a6e44>] (register_framebuffer+0x1e0/0x2f8)
[<c03a6e44>] (register_framebuffer) from [<c04153c0>] (__drm_fb_helper_initial_config_and_unlock+0x2fc/0x50c)
[<c04153c0>] (__drm_fb_helper_initial_config_and_unlock) from [<c04158c8>] (drm_fbdev_client_hotplug+0xe8/0x1b8)
[<c04158c8>] (drm_fbdev_client_hotplug) from [<c0415a20>] (drm_fbdev_generic_setup+0x88/0x118)
[<c0415a20>] (drm_fbdev_generic_setup) from [<c043f060>] (sun4i_drv_bind+0x128/0x160)
[<c043f060>] (sun4i_drv_bind) from [<c044b598>] (try_to_bring_up_master+0x164/0x1a0)
[<c044b598>] (try_to_bring_up_master) from [<c044b668>] (__component_add+0x94/0x140)
[<c044b668>] (__component_add) from [<c0445e1c>] (sun6i_dsi_probe+0x144/0x234)
[<c0445e1c>] (sun6i_dsi_probe) from [<c0452ef4>] (platform_drv_probe+0x48/0x9c)
[<c0452ef4>] (platform_drv_probe) from [<c04512cc>] (really_probe+0x1dc/0x2c8)
[<c04512cc>] (really_probe) from [<c0451518>] (driver_probe_device+0x60/0x160)
[<c0451518>] (driver_probe_device) from [<c044f7a4>] (bus_for_each_drv+0x74/0xb8)
[<c044f7a4>] (bus_for_each_drv) from [<c045107c>] (__device_attach+0xd0/0x13c)
[<c045107c>] (__device_attach) from [<c0450474>] (bus_probe_device+0x84/0x8c)
[<c0450474>] (bus_probe_device) from [<c0450900>] (deferred_probe_work_func+0x64/0x90)
[<c0450900>] (deferred_probe_work_func) from [<c0135970>] (process_one_work+0x204/0x420)
[<c0135970>] (process_one_work) from [<c013690c>] (worker_thread+0x274/0x5a0)
[<c013690c>] (worker_thread) from [<c013b3d8>] (kthread+0x11c/0x14c)
[<c013b3d8>] (kthread) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
Exception stack(0xde539fb0 to 0xde539ff8)
9fa0: 00000000 00000000 00000000 00000000
9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9fe0: 00000000 00000000 00000000 00000000 00000013 00000000
---[ end trace b57eb1e5c64c6b8b ]---
random: fast init done
[drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:46:crtc-0] flip_done timed out
[drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CONNECTOR:48:DSI-1] flip_done timed out
[drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [PLANE:30:plane-0] flip_done timed out
With the terms(as described in above diagram) fixed, the panel
displays correctly without any timeouts.
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003064527.15128-2-jagan@amarulasolutions.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be4c60b563 ]
When populating the pinctrl mapping table entries for a device, the
'dev_name' field for each entry is initialised to point directly at the
string returned by 'dev_name()' for the device and subsequently used by
'create_pinctrl()' when looking up the mappings for the device being
probed.
This is unreliable in the presence of calls to 'dev_set_name()', which may
reallocate the device name string leaving the pinctrl mappings with a
dangling reference. This then leads to a use-after-free every time the
name is dereferenced by a device probe:
| BUG: KASAN: invalid-access in strcmp+0x20/0x64
| Read of size 1 at addr 13ffffc153494b00 by task modprobe/590
| Pointer tag: [13], memory tag: [fe]
|
| Call trace:
| __kasan_report+0x16c/0x1dc
| kasan_report+0x10/0x18
| check_memory_region
| __hwasan_load1_noabort+0x4c/0x54
| strcmp+0x20/0x64
| create_pinctrl+0x18c/0x7f4
| pinctrl_get+0x90/0x114
| devm_pinctrl_get+0x44/0x98
| pinctrl_bind_pins+0x5c/0x450
| really_probe+0x1c8/0x9a4
| driver_probe_device+0x120/0x1d8
Follow the example of sysfs, and duplicate the device name string before
stashing it away in the pinctrl mapping entries.
Cc: Linus Walleij <linus.walleij@linaro.org>
Reported-by: Elena Petrova <lenaptr@google.com>
Tested-by: Elena Petrova <lenaptr@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20191002124206.22928-1-will@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fef0faa1c ]
[why]
Some ODM-related register settings are inconsistently updated by VBIOS, causing
the state in DC to be invalid, which would then end up crashing in certain
use-cases (such as disable/enable device).
[how]
Check the enabled status of the second pipe when determining the number of
OPTC sources. If the second pipe is disabled, set the number of sources to 1
regardless of other settings (that may not be updated correctly).
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc6df017e5 ]
Offchannel management frames were failing:
[18099.253732] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18102.293686] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18105.333653] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18108.373712] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18111.413687] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e36c0
[18114.453726] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3f00
[18117.493773] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e36c0
[18120.533631] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3f00
This bug appears to have been added between 4.0 (which works for us),
and 4.4, which does not work.
I think this is because the tx-offchannel logic gets in a loop when
ath10k_mac_tx_frm_has_freq(ar) is false, so pkt is never actually
sent to the firmware for transmit.
This patch fixes the problem on 4.9 for me, and now HS20 clients
can work again with my firmware.
Antonio: tested with 10.4-3.5.3-00057 on QCA4019 and QCA9888
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Antonio Quartulli <antonio.quartulli@kaiwoo.ai>
[kvalo@codeaurora.org: improve commit log, remove unneeded parenthesis]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e5705c635 ]
When building cpupower with clang, the following warning appears:
utils/idle_monitor/hsw_ext_idle.c:42:16: warning: initializer overrides
prior initialization of this subobject [-Winitializer-overrides]
.desc = N_("Processor Package C2"),
^~~~~~~~~~~~~~~~~~~~~~
./utils/helpers/helpers.h:25:33: note: expanded from macro 'N_'
#define N_(String) gettext_noop(String)
^~~~~~
./utils/helpers/helpers.h:23:30: note: expanded from macro
'gettext_noop'
#define gettext_noop(String) String
^~~~~~
utils/idle_monitor/hsw_ext_idle.c:41:16: note: previous initialization
is here
.desc = N_("Processor Package C9"),
^~~~~~~~~~~~~~~~~~~~~~
./utils/helpers/helpers.h:25:33: note: expanded from macro 'N_'
#define N_(String) gettext_noop(String)
^~~~~~
./utils/helpers/helpers.h:23:30: note: expanded from macro
'gettext_noop'
#define gettext_noop(String) String
^~~~~~
1 warning generated.
This appears to be a copy and paste or merge mistake because the name
and id fields both have PC9 in them, not PC2. Remove the second
assignment to fix the warning.
Fixes: 7ee767b69b ("cpupower: Add Haswell family 0x45 specific idle monitor to show PC8,9,10 states")
Link: https://github.com/ClangBuiltLinux/linux/issues/718
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1463b371af ]
The driver stores crop rectangle settings supposed to be in line with
hardware state in a device private structure. Since the driver initial
submission, crop rectangle width and height settings are not updated
correctly when rectangle offset settings are applied on hardware. If
an error occurs while the device is updated, the stored settings my no
longer reflect hardware state and consecutive calls to .get_selection()
as well as .get/set_fmt() may return incorrect information. That in
turn may affect ability of a bridge device to use correct DMA transfer
settings if such incorrect informamtion on active frame format returned
by .get/set_fmt() is used.
Assuming a failed update of the device means its actual settings haven't
changed, update crop rectangle width and height settings stored in the
device private structure correctly while the rectangle offset is
successfully applied on hardware so the stored values always reflect
actual hardware state to the extent possible.
Fixes: 2f6e240479 ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3143b459de ]
The driver stores frame format settings supposed to be in line with
hardware state in a device private structure. Since the driver initial
submission, those settings are updated before they are actually applied
on hardware. If an error occurs on device update, the stored settings
my not reflect hardware state anymore and consecutive calls to
.get_fmt() may return incorrect information. That in turn may affect
ability of a bridge device to use correct DMA transfer settings if such
incorrect informmation on active frame format returned by .get_fmt() is
used.
Assuming a failed device update means its state hasn't changed, update
frame format related settings stored in the device private structure
only after they are successfully applied so the stored values always
reflect hardware state as closely as possible.
Fixes: 2f6e240479 ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d669fbfca ]
The initial registers sequence is only loaded at probe
time. Afterward only the resolution and format specific
register are modified. Care must be taken to make sure
registers modified by one resolution setting are reverted
back when another resolution is programmed.
This was not done properly for the 720p case.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b188d6ba2 ]
Commit 4f996594ce ("[media] v4l2: make vidioc_s_crop const")
introduced a writable copy of constified user requested crop rectangle
in order to be able to perform hardware alignments on it. Later
on, commit 10d5509c8d ("[media] v4l2: remove g/s_crop from video
ops") replaced s_crop() video operation using that const argument with
set_selection() pad operation which had a corresponding argument not
constified, however the original behavior of the driver was not
restored. Since that time, any hardware alignment applied on a user
requested crop rectangle is not passed back to the user calling
.set_selection() as it should be.
Fix the issue by dropping the copy and replacing all references to it
with references to the crop rectangle embedded in the user argument.
Fixes: 10d5509c8d ("[media] v4l2: remove g/s_crop from video ops")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85c4043f1d ]
In ov2659_s_stream() return value for invoked function should be checked
and propagated.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c404af950d ]
Since commit afd9690c72 ("[media] ov6650: convert to the control
framework"), if an error occurs during initialization of a control
handler, resources possibly allocated to the handler are not freed
before device initialiaton is aborted. Fix it.
Fixes: afd9690c72 ("[media] ov6650: convert to the control framework")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c362f77a24 ]
Currently, if start streaming -> stop streaming -> start streaming
sequence is executed, driver will end job prematurely, if ctx->translen
is higher than 1, because "aborting" flag is still set from previous
stop streaming command.
Fix that by clearing "aborting" flag in start streaming handler.
Fixes: 96d8eab5d0 ("V4L/DVB: [v5,2/2] v4l: Add a mem-to-mem videobuf framework test device")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9cc4cbcdf ]
At the beginning of the probe function, we have a call to
'request_muxed_region(BRA_SMB_BASE_ADDR, 7, "CEC00001")()'
A corresponding 'release_region()' is performed in the remove function but
is lacking in the error handling path.
Add it.
Fixes: b03c2fb97a ("media: add SECO cec driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13aa21cfe9 ]
VIDIOC_S_STD should not return an error if the value is identical
to the current one.
This error was highlighted by the v4l2-compliance test.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3b0ffa1d7 ]
In spi_gpio_probe an SPI master is allocated via spi_alloc_master, but
this controller should be released if devm_add_action_or_reset fails,
otherwise memory leaks. In order to avoid leak spi_contriller_put must
be called in case of failure for devm_add_action_or_reset.
Fixes: 8b797490b4 ("spi: gpio: Make sure spi_master_put() is called in every error path")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Link: https://lore.kernel.org/r/20190930205241.5483-1-navid.emamdoost@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f59769c52c ]
When initially turning a crtc on, drm_reset_vblank_timestamp will
set the vblank timestamp to 0 for any driver that doesn't provide
a ->get_vblank_timestamp() hook.
Unfortunately, the FLIP_COMPLETE event depends on that timestamp,
and the only way to regenerate a valid one is to have vblank
interrupts enabled and have a valid in-ISR call to
drm_crtc_handle_vblank.
Additionally, if the user doesn't request vblanks but _does_ request
FLIP_COMPLETE events, we still don't have a good timestamp: it'll be the
same stamp as the last vblank one.
Work around the issue by always enabling vblanks when the CRTC is on.
Reducing the amount of time that PL0 has to be unmasked would be nice to
fix at a later time.
Changes since v1 [https://patchwork.freedesktop.org/patch/331727/]:
- moved drm_crtc_vblank_put call to the ->atomic_disable() hook
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Ayan kumar halder <ayan.halder@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191001142121.13939-1-mihail.atanassov@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7718cf03c3 ]
In case we don't set the sg_prot_tablesize, the scsi layer assign the
default size (65535 entries). We should limit this size since we should
take into consideration the underlaying device capability. This cap is
considered when calculating the sg_tablesize. Otherwise, for example,
we can get that /sys/block/sdb/queue/max_segments is 128 and
/sys/block/sdb/queue/max_integrity_segments is 65535.
Link: https://lore.kernel.org/r/1569359027-10987-1-git-send-email-maxg@mellanox.com
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d98ddae85a ]
In a multiradio board with one QCA9984 and one AR9987
after enabling the crashdump with module parameter
coredump_mask=7, below backtrace is seen.
vmalloc: allocation failure: 0 bytes
kworker/u4:0: page allocation failure: order:0, mode:0x80d2
CPU: 0 PID: 6 Comm: kworker/u4:0 Not tainted 3.14.77 #130
Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core]
(unwind_backtrace) from [<c021abf8>] (show_stack+0x10/0x14)
(dump_stack+0x80/0xa0)
(warn_alloc_failed+0xd0/0xfc)
(__vmalloc_node_range+0x1b4/0x1d8)
(__vmalloc_node+0x34/0x40)
(vzalloc+0x24/0x30)
(ath10k_coredump_register+0x6c/0x88 [ath10k_core])
(ath10k_core_register_work+0x350/0xb34 [ath10k_core])
(process_one_work+0x20c/0x32c)
(worker_thread+0x228/0x360)
This is due to ath10k_hw_mem_layout is not defined for AR9987.
For coredump undefined hw ramdump_size is 0.
Check for the ramdump_size before allocation memory.
Tested on: AR9987, QCA9984
FW version: 10.4-3.9.0.2-00044
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7666dfd533 ]
This reverts commit e167d723e1.
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, the SEL_SIMCARD_{0,1} definition was to be deleted. However,
this errata merely fixed an accidental double definition in the Hardware
User's Manual Rev. 1.00. The real definition is still present in later
revisions of the manual (Rev. 1.50 and Rev. 2.00).
Hence revert the commit to recover the definition.
Based on a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190904121658.2617-4-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3672bc7093 ]
This reverts commit e87882eb9b.
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, the SEL_SSI2_{0,1} definition was to be deleted. However,
this errata merely fixed an accidental double definition in the Hardware
User's Manual Rev. 1.00. The real definition is still present in later
revisions of the manual (Rev. 1.50 and Rev. 2.00).
Hence revert the commit to recover the definition.
Based on a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190904121658.2617-3-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7da413a185 ]
alloc_workqueue is not checked for errors and as a result,
a potential NULL dereference could occur.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f93616951 ]
In rtl_usb_probe if allocation for usb_data fails the allocated hw
should be released. In addition the allocated rtlpriv->usb_data should
be released on error handling path.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 228241944a ]
Inside a nested 'else' block at the beginning of this function is a
call that assigns 'psta' to the return value of 'rtw_get_stainfo()'.
If 'rtw_get_stainfo()' returns NULL and the flow of control reaches
the 'else if' where 'psta' is dereferenced, then we will dereference
a NULL pointer.
Fix this by checking if 'psta' is not NULL before reading its
'psta->qos_option' data member.
Addresses-Coverity: ("Dereference null return value")
Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/r/20190926150317.5894-1-connor.kuehl@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca312438cf ]
In rtl8192_tx on error handling path allocated urbs and also skb should
be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Link: https://lore.kernel.org/r/20190920025137.29407-1-navid.emamdoost@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d56276a13c ]
When calculating the HDMI PLL settings for a DMT mode PHY frequency,
use the correct max fractional PLL value for G12A VPU.
With this fix, we can finally setup the 1024x768-60 mode.
Fixes: 202b9808f8 ("drm/meson: Add G12A Video Clock setup")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828132311.23881-1-narmstrong@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f918a728c ]
This change is necessary for spidev devices (e.g. /dev/spidev3.0) working
in the slave mode (like NXP's dspi driver for Vybrid SoC).
When SPI HW works in this mode - the master is responsible for providing
CS and CLK signals. However, when some fault happens - like for example
distortion on SPI lines - the SPI Linux driver needs a chance to recover
from this abnormal situation and prepare itself for next (correct)
transmission.
This change doesn't pose any threat on drivers working in master mode as
spi_slave_abort() function checks if SPI slave mode is supported.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Link: https://lore.kernel.org/r/20190924110547.14770-2-lukma@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20190925091143.15468-2-lukma@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Daniel T. Lee