Adding Microchip 9477 Phy included in KSZ9477 Switch.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support for Cortina PHY drivers. Support only CS4340 for now.
The phys are not compatible with IEEE 802.3 clause 22/45 registers.
Implement proper read_status support. The generic 10G phy driver causes
bus register access errors.
The driver should be described using the "ethernet-phy-id" device tree
compatible.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet drivers will attach/connect to a PHY device before calling
register_netdevice() which is responsible for calling netdev_register_kobject()
which would do the network device's kobject initialization. In such a case,
sysfs_create_link() would return -ENOENT because the network device's kobject
is not ready yet, and we would fail to connect to the PHY device.
In order to keep things simple and symetrical, we just take the success path as
indicative of the ability to access the network device's kobject, and create
the second link if that's the case.
Fixes: 5568363f0c ("net: phy: Create sysfs reciprocal links for attached_dev/phydev")
Reported-by: Woojung Hung <Woojung.Huh@microchip.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net'
restricting a HW workaround alongside cleanups in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring all the page names together, remove the repeats, and make them
uniform.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a common pattern of first reading the currently selected page
and then changing to another page. Add a helper to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
EXT_ADDR_PAGE is the same meaning as MII_MARVELL_PHY_PAGE, i.e. change
page. Replace it will calls to the helpers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace magic numbers for PHY pages with symbolic names.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently no way for a program scanning /sys to know whether a
network device is attached to a particular PHY device, just like the PHY
device is not pointed back to its attached network device.
Create a symbolic link in the network device's namespace named "phydev"
which points to the PHY device and create a symbolic link in the PHY
device's namespace named "attached_dev" that points back to the network
device. These links are set up during phy_attach_direct() and removed
during phy_detach() for symetry.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit af6b6967d6 ("net: phy: export genphy_config_init()") introduced
this EXPORT_SYMBOL and put it after gen10g_soft_reset() instead of
directly after genphy_config_init. Probably this happend when the patch
was applied because http://patchwork.ozlabs.org/patch/339622/ looks ok.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88m1101 has an errata when configuring autoneg. However, it was
being applied to many other Marvell PHYs as well. Limit its scope to
just the 88m1101.
Fixes: 76884679c6 ("phylib: Add support for Marvell 88e1111S and 88e1145")
Reported-by: Daniel Walker <danielwa@cisco.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build errors by making this driver depend on OF_MDIO, like
several other similar drivers do.
drivers/built-in.o: In function `octeon_mdiobus_remove':
mdio-octeon.c:(.text+0x196ee0): undefined reference to `mdiobus_unregister'
mdio-octeon.c:(.text+0x196ee8): undefined reference to `mdiobus_free'
drivers/built-in.o: In function `octeon_mdiobus_probe':
mdio-octeon.c:(.text+0x196f1d): undefined reference to `devm_mdiobus_alloc_size'
mdio-octeon.c:(.text+0x196ffe): undefined reference to `of_mdiobus_register'
mdio-octeon.c:(.text+0x197010): undefined reference to `mdiobus_free'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Makes the code a bit more readable, and solves quite a few checkpatch
warnings of lines longer than 80 characters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break big functions up by using a number of smaller helper
function. Solves some of the over 80 lines warnings, by reducing the
indentation level.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid multiple assignments
Comparisons should place the constant on the right side of the test
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the extra blank lines, add one in where recommended.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use net style comment blocks, and wrap one block with long lines.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit fa8cddaf90 ("net phylib: Remove unnecessary condition check in phy")
removed the only place where the PHY flag PHY_HAS_MAGICANEG was
checked. But it left the flag being set in the drivers. Remove the flag.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch,
- refactors mac access routine
- adds lock to protect mac indirect access
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device node iterators put the previous value of the index variable, so an
explicit put causes a double put.
In particular, of_mdiobus_register can fail before doing anything
interesting, so one could view it as a no-op from the reference count
point of view.
Generated by: scripts/coccinelle/iterators/device_node_continue.cocci
CC: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The API convention makes it that a given MDIO bus reset should be able
to access PHY devices in its reset() callback and perform additional
MDIO accesses in order to bring the bus and PHYs in a working state.
Commit 69226896ad ("mdio_bus: Issue GPIO RESET to PHYs.") broke that
contract by first calling bus->reset() and then release all PHYs from
reset using their shared GPIO line, so restore the expected
functionality here.
Fixes: 69226896ad ("mdio_bus: Issue GPIO RESET to PHYs.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential unnecessary refcount decrement on error path of
put_device(&pb->mii_bus->dev), as it is possible to avoid the
of_mdio_find_bus() call if mux_bus is specified by the calling function.
The same put_device() is not called in the error path if the
devm_kzalloc of pb fails. This caused the variable used in the
put_device() to be changed, as the pb pointer was obviously not set up.
There is an unnecessary of_node_get() on child_bus_node if the
of_mdiobus_register() is successful, as the
for_each_available_child_of_node() automatically increments this.
Thus the refcount on this node will always be +1 more than it should be.
There is no of_node_put() on child_bus_node if the of_mdiobus_register()
call fails.
Finally, it is lacking devm_kfree() of pb in the error path. While this
might not be technically necessary, it was present in other parts of the
function. So, I am adding it where necessary to make it uniform.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: f20e6657a8 ("mdio: mux: Enhanced MDIO mux framework for integrated multiplexers")
Fixes: 0ca2997d14 ("netdev/of/phy: Add MDIO bus multiplexer support.")
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error is encountered in mdio_mux_init(), the error path will call
mdiobus_free(). Since mdiobus_register() has been called prior to
mdio_mux_init(), the bus->state will not be MDIOBUS_UNREGISTERED. This
causes a BUG_ON() in mdiobus_free(). To correct this issue, add an
error path for mdio_mux_init() which calls mdiobus_unregister() prior to
mdiobus_free().
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: 98bc865a1e ("net: mdio-mux: Add MDIO mux driver for iProc SoCs")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows users to enable/disable internal TX and/or RX
clock delay for BCM5481x series PHYs so as to satisfy RGMII timing
specifications.
On a particular platform, whether TX and/or RX clock delay is required
depends on how PHY connected to the MAC IP. This requirement can be
specified through "phy-mode" property in the platform device tree.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 99f81afc13.
It was papering over the real problem, which is fixed by commit
f555f34fdc ("net: phy: fix auto-negotiation stall due to unavailable
interrupt")
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet link on an interrupt driven PHY was not coming up if the Ethernet
cable was plugged before the Ethernet interface was brought up.
The patch trigger PHY state machine to update link state if PHY was requested to
do auto-negotiation and auto-negotiation complete flag already set.
During power-up cycle the PHY do auto-negotiation, generate interrupt and set
auto-negotiation complete flag. Interrupt is handled by PHY state machine but
doesn't update link state because PHY is in PHY_READY state. After some time
MAC bring up, start and request PHY to do auto-negotiation. If there are no new
settings to advertise genphy_config_aneg() doesn't start PHY auto-negotiation.
PHY continue to stay in auto-negotiation complete state and doesn't fire
interrupt. At the same time PHY state machine expect that PHY started
auto-negotiation and is waiting for interrupt from PHY and it won't get it.
Fixes: 321beec504 ("net: phy: Use interrupts when available in NOLINK state")
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Cc: stable <stable@vger.kernel.org> # v4.9+
Tested-by: Roger Quadros <rogerq@ti.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boards [1] leave the PHYs at an invalid state
during system power-up or reset thus causing unreliability
issues with the PHY which manifests as PHY not being detected
or link not functional. To fix this, these PHYs need to be RESET
via a GPIO connected to the PHY's RESET pin.
Some boards have a single GPIO controlling the PHY RESET pin of all
PHYs on the bus whereas some others have separate GPIOs controlling
individual PHY RESETs.
In both cases, the RESET de-assertion cannot be done in the PHY driver
as the PHY will not probe till its reset is de-asserted.
So do the RESET de-assertion in the MDIO bus driver.
[1] - am572x-idk, am571x-idk, a437x-idk
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both conflict were simple overlapping changes.
In the kaweth case, Eric Dumazet's skb_cow() bug fix overlapped the
conversion of the driver in net-next to use in-netdev stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is prompted by a static checker warning about a potential
use after free. The concern is that netif_rx_ni() can free "skb" and we
call it twice.
When I look at the commit that added this, it looks like some stray
lines were added accidentally. It doesn't make sense to me that we
would recieve the same data two times. I asked the author but never
recieved a response.
I can't test this code, but I'm pretty sure my patch is correct.
Fixes: 4b063258ab ("dp83640: Delay scheduled work.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A function in kernel/bpf/syscall.c which got a bug fix in 'net'
was moved to kernel/bpf/verifier.c in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a copy and paste buglet. We meant to test for ->write_mmd but
we test for ->read_mmd.
Fixes: 1ee6b9bc62 ("net: phy: make phy_(read|write)_mmd() generic MMD accessors")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the command:
ethtool --phy-statistics eth0
will cause system crash with meassage "Unable to handle kernel NULL pointer
dereference at virtual address 00000010" from:
(kszphy_get_stats) from [<c069f1d8>] (ethtool_get_phy_stats+0xd8/0x210)
(ethtool_get_phy_stats) from [<c06a0738>] (dev_ethtool+0x5b8/0x228c)
(dev_ethtool) from [<c06b5484>] (dev_ioctl+0x3fc/0x964)
(dev_ioctl) from [<c0679f7c>] (sock_ioctl+0x170/0x2c0)
(sock_ioctl) from [<c02419d4>] (do_vfs_ioctl+0xa8/0x95c)
(do_vfs_ioctl) from [<c02422c4>] (SyS_ioctl+0x3c/0x64)
(SyS_ioctl) from [<c0107d60>] (ret_fast_syscall+0x0/0x44)
The reason: phy_driver structure for KSZ9031 phy has no .probe() callback
defined. As result, struct phy_device *phydev->priv pointer will not be
initializes (null).
This issue will affect also following phys:
KSZ8795, KSZ886X, KSZ8873MLL, KSZ9031, KSZ9021, KSZ8061, KS8737
Fix it by:
- adding .probe() = kszphy_probe() callback to KSZ9031, KSZ9021
phys. The kszphy_probe() can be re-used as it doesn't do any phy specific
settings.
- removing statistic callbacks from other phys (KSZ8795, KSZ886X,
KSZ8873MLL, KSZ8061, KS8737) as they doesn't have corresponding
statistic counters.
Fixes: 2b2427d064 ("phy: micrel: Add ethtool statistics counters")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the loop in phy_supported_speeds().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylib has some undesirable behaviour when forcing a link mode through
ethtool. phylib uses this code:
idx = phy_find_valid(phy_find_setting(phydev->speed, phydev->duplex),
features);
to find an index in the settings table. phy_find_setting() starts at
index 0, and scans upwards looking for an exact speed and duplex match.
When it doesn't find it, it returns MAX_NUM_SETTINGS - 1, which is
10baseT-Half duplex.
phy_find_valid() then scans from the point (and effectively only checks
one entry) before bailing out, returning MAX_NUM_SETTINGS - 1.
phy_sanitize_settings() then sets ->speed to SPEED_10 and ->duplex to
DUPLEX_HALF whether or not 10baseT-Half is supported or not. This goes
against all the comments against these functions, and 10baseT-Half may
not even be supported by the hardware.
Rework these functions, introducing a new method of scanning the table.
There are two modes of lookup that phylib wants: exact, and inexact.
- in exact mode, we return either an exact match or failure
- in inexact mode, we return an exact match if it exists, a match at
the highest speed that is not greater than the requested speed
(ignoring duplex), or failing that, the lowest supported speed, or
failure.
The biggest difference is that we always check whether the entry is
supported before further consideration, so all unsupported entries are
not considered as candidates.
This results in arguably saner behaviour, better matches the comments,
and is probably what users would expect.
This becomes important as ethernet speeds increase, PHYs exist which do
not support the 10Mbit speeds, and half-duplex is likely to become
obsolete - it's already not even an option on 10Gbit and faster links.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
EEE is able to work in any PHY interface mode, there is nothing which
fundamentally restricts it to only a few modes. For example, EEE works
in SGMII mode with the Marvell 88E1512.
Rather than just adding SGMII mode to the list, Florian suggests
removing the list of interface modes entirely:
It actually sounds like we should just kill the check entirely,
it does not appear that any of the interface mode would not
fundamentally be able to support EEE, because the "lowest" mode
we support is MII, and even there it's quite possible to support
EEE.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the EEE advertisment is changed, we should restart autonegotiation
to update the link partner with the new EEE settings. Add this trigger
but only if the advertisment has changed.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently allow userspace to set any EEE advertisments it desires,
whether or not the PHY supports them. For example:
# ethtool --set-eee eth1 advertise 0xffffffff
# ethtool --show-eee eth1
EEE Settings for eth1:
EEE status: disabled
Tx LPI: disabled
Supported EEE link modes: 100baseT/Full
1000baseT/Full
10000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
1000baseKX/Full
10000baseT/Full
10000baseKX4/Full
10000baseKR/Full
Clearly, this is not sane, we should only allow link modes that are
supported to be advertised (as we do elsewhere.) Ensure that we mask
the MDIO_AN_EEE_ADV value with the capabilities retrieved from the
MDIO_PCS_EEE_ABLE register.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio-boardinfo contains code that is helpful for platforms to register
specific MDIO bus devices independent of how CONFIG_MDIO_DEVICE or
CONFIG_PHYLIB will be selected (modular or built-in). In order to make
that possible, let's do the following:
- descend into drivers/net/phy/ unconditionally
- make mdiobus_setup_mdiodev_from_board_info() take a callback argument
which allows us not to expose the internal MDIO board info list and
mutex, yet maintain the logic within the same file
- relocate the code that creates a MDIO device into
drivers/net/phy/mdio_bus.c
- build mdio-boardinfo.o into the kernel as soon as MDIO_DEVICE is
defined (y or m)
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Fixes: 648ea01340 ("net: phy: Allow pre-declaration of MDIO devices")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new configuration symbol: MDIO_DEVICE which allows building
the MDIO devices and bus code, without pulling in the entire Ethernet
PHY library and devices code.
PHYLIB nows select MDIO_DEVICE and the relevant Makefile files are
updated to reflect that.
When MDIO_DEVICE (MDIO bus/device only) is selected, but not PHYLIB, we
have mdio-bus.ko as a loadable module, and it does not have a
module_exit() function because the safety of removing a bus class is
unclear.
When both MDIO_DEVICE and PHYLIB are enabled, we need to assemble
everything into a common loadable module: libphy.ko because of nasty
circular dependencies between phy.c, phy_device.c and mdio_bus.c which
are really tough to untangle.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom MDIO UniMAC driver uses routines provided by of_mdio.c which is
guarded by CONFIG_OF_MDIO.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PHY is halted on stop, then do not set the state to PHY_UP. This
ensures the phy will be restarted later in phy_start when the machine is
started again.
Fixes: 00db8189d9 ("This patch adds a PHY Abstraction Layer to the Linux Kernel, enabling ethernet drivers to remain as ignorant as is reasonable of the connected PHY's design and operation details.")
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Acked-by: Xander Huff <xander.huff@ni.com>
Acked-by: Kyle Roeschley <kyle.roeschley@ni.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can build modular code that uses mdiobus_register_board_info() which would
lead to linking failure since this symbol is not expoerted.
Fixes: 648ea01340 ("net: phy: Allow pre-declaration of MDIO devices")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make mmd_phy_indirect() use the same terminology as the rest of the
code, making clear what each address is - phy address, devad, and
register number.
While here, remove the "inline" from this static function, leaving
it to the compiler to decide whether to inline this function, and
get rid of unnecessary parens.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
