ARM: perf: Set ARMv7 SDER SUNIDEN bit
ARMv7 counters other than the CPU cycle counter only work if the Secure Debug Enable Register (SDER) SUNIDEN bit is set. Since access to the SDER is only possible in secure state, it will only be done if the device tree property "secure-reg-access" is set. Without this: Performance counter stats for 'sleep 1': 14606094 cycles # 0.000 GHz 0 instructions # 0.00 insns per cycle After applying: Performance counter stats for 'sleep 1': 5843809 cycles 2566484 instructions # 0.44 insns per cycle 1.020144000 seconds time elapsed Some platforms (eg i.MX53) may also need additional platform specific setup. Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com> Signed-off-by: Pooya Keshavarzi <Pooya.Keshavarzi@de.bosch.com> Signed-off-by: George G. Davis <george_davis@mentor.com> [will: add warning if property is found on arm64] Signed-off-by: Will Deacon <will.deacon@arm.com>
This commit is contained in:
parent
92e963f50f
commit
8d1a0ae724
|
@ -46,6 +46,16 @@ Optional properties:
|
|||
- qcom,no-pc-write : Indicates that this PMU doesn't support the 0xc and 0xd
|
||||
events.
|
||||
|
||||
- secure-reg-access : Indicates that the ARMv7 Secure Debug Enable Register
|
||||
(SDER) is accessible. This will cause the driver to do
|
||||
any setup required that is only possible in ARMv7 secure
|
||||
state. If not present the ARMv7 SDER will not be touched,
|
||||
which means the PMU may fail to operate unless external
|
||||
code (bootloader or security monitor) has performed the
|
||||
appropriate initialisation. Note that this property is
|
||||
not valid for non-ARMv7 CPUs or ARMv7 CPUs booting Linux
|
||||
in Non-secure state.
|
||||
|
||||
Example:
|
||||
|
||||
pmu {
|
||||
|
|
|
@ -712,6 +712,11 @@ static const struct attribute_group *armv7_pmuv2_attr_groups[] = {
|
|||
#define ARMV7_EXCLUDE_USER (1 << 30)
|
||||
#define ARMV7_INCLUDE_HYP (1 << 27)
|
||||
|
||||
/*
|
||||
* Secure debug enable reg
|
||||
*/
|
||||
#define ARMV7_SDER_SUNIDEN BIT(1) /* Permit non-invasive debug */
|
||||
|
||||
static inline u32 armv7_pmnc_read(void)
|
||||
{
|
||||
u32 val;
|
||||
|
@ -1094,7 +1099,13 @@ static int armv7pmu_set_event_filter(struct hw_perf_event *event,
|
|||
static void armv7pmu_reset(void *info)
|
||||
{
|
||||
struct arm_pmu *cpu_pmu = (struct arm_pmu *)info;
|
||||
u32 idx, nb_cnt = cpu_pmu->num_events;
|
||||
u32 idx, nb_cnt = cpu_pmu->num_events, val;
|
||||
|
||||
if (cpu_pmu->secure_access) {
|
||||
asm volatile("mrc p15, 0, %0, c1, c1, 1" : "=r" (val));
|
||||
val |= ARMV7_SDER_SUNIDEN;
|
||||
asm volatile("mcr p15, 0, %0, c1, c1, 1" : : "r" (val));
|
||||
}
|
||||
|
||||
/* The counter and interrupt enable registers are unknown at reset. */
|
||||
for (idx = ARMV7_IDX_CYCLE_COUNTER; idx < nb_cnt; ++idx) {
|
||||
|
|
|
@ -889,6 +889,15 @@ int arm_pmu_device_probe(struct platform_device *pdev,
|
|||
if (node && (of_id = of_match_node(of_table, pdev->dev.of_node))) {
|
||||
init_fn = of_id->data;
|
||||
|
||||
pmu->secure_access = of_property_read_bool(pdev->dev.of_node,
|
||||
"secure-reg-access");
|
||||
|
||||
/* arm64 systems boot only as non-secure */
|
||||
if (IS_ENABLED(CONFIG_ARM64) && pmu->secure_access) {
|
||||
pr_warn("ignoring \"secure-reg-access\" property for arm64\n");
|
||||
pmu->secure_access = false;
|
||||
}
|
||||
|
||||
ret = of_pmu_irq_cfg(pmu);
|
||||
if (!ret)
|
||||
ret = init_fn(pmu);
|
||||
|
|
|
@ -104,6 +104,7 @@ struct arm_pmu {
|
|||
atomic_t active_events;
|
||||
struct mutex reserve_mutex;
|
||||
u64 max_period;
|
||||
bool secure_access; /* 32-bit ARM only */
|
||||
struct platform_device *plat_device;
|
||||
struct pmu_hw_events __percpu *hw_events;
|
||||
struct notifier_block hotplug_nb;
|
||||
|
|
Loading…
Reference in a new issue