The test application controls the OTG pin itself,
not via the usb OTG driver. A change between kern
4.1 and 4.9 causes the regulator to take the
gpio pin even if there are no references to it.
This commit removes the vbus gpio from the
driver, so that the test application works again.
There are two flavours of the device tree today, one
for the main application and one for the testing
application used in the factory. This patch gathers
them both in the same branch, to be able to use the
same kernel for both factory and end user.
Add a default config based on imx6 default config
Update our default config
Update defconfig
Clean out unused stuff from defconfig
Re-add IMX serial to defconfig
Re-enable large files support
Enable PXPv2 in defconfig
Disable auto update mode in EPDC driver
Use correct poweroff driver
defconfig: switch to interactive cpu scheduler, enable cpu idle
defconfig: disable cyttsp debug output
defconfig: enable usb gadget support
defconfig: enable fsl_otp, remove some debug output
defconfig: Enable brcmfmac
defconfig: add reset controller for wifi for powering it up
defconfig: power management, support more USB devices, gpio charger support, CAAM support for RNG
defconfig: enable nbd for vfatbuse, enable reset by syscon, fuck around with spi
defconfig enable f2fs support
defconfig: Disable busfreq
defconfig: re-enable cpu frequency scaling
defconfig: use ethernet gadget by default
[ upstream commit d269176e76 ]
While working on 16338a9b3a ("bpf, arm64: fix out of bounds access in
tail call") I noticed that ppc64 JIT is partially affected as well. While
the bound checking is correctly performed as unsigned comparison, the
register with the index value however, is never truncated into 32 bit
space, so e.g. a index value of 0x100000000ULL with a map of 1 element
would pass with PPC_CMPLW() whereas we later on continue with the full
64 bit register value. Therefore, as we do in interpreter and other JITs
truncate the value to 32 bit initially in order to fix access.
Fixes: ce0761419f ("powerpc/bpf: Implement support for tail calls")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Tested-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ upstream commit 16338a9b3a ]
I recently noticed a crash on arm64 when feeding a bogus index
into BPF tail call helper. The crash would not occur when the
interpreter is used, but only in case of JIT. Output looks as
follows:
[ 347.007486] Unable to handle kernel paging request at virtual address fffb850e96492510
[...]
[ 347.043065] [fffb850e96492510] address between user and kernel address ranges
[ 347.050205] Internal error: Oops: 96000004 [#1] SMP
[...]
[ 347.190829] x13: 0000000000000000 x12: 0000000000000000
[ 347.196128] x11: fffc047ebe782800 x10: ffff808fd7d0fd10
[ 347.201427] x9 : 0000000000000000 x8 : 0000000000000000
[ 347.206726] x7 : 0000000000000000 x6 : 001c991738000000
[ 347.212025] x5 : 0000000000000018 x4 : 000000000000ba5a
[ 347.217325] x3 : 00000000000329c4 x2 : ffff808fd7cf0500
[ 347.222625] x1 : ffff808fd7d0fc00 x0 : ffff808fd7cf0500
[ 347.227926] Process test_verifier (pid: 4548, stack limit = 0x000000007467fa61)
[ 347.235221] Call trace:
[ 347.237656] 0xffff000002f3a4fc
[ 347.240784] bpf_test_run+0x78/0xf8
[ 347.244260] bpf_prog_test_run_skb+0x148/0x230
[ 347.248694] SyS_bpf+0x77c/0x1110
[ 347.251999] el0_svc_naked+0x30/0x34
[ 347.255564] Code: 9100075a d280220a 8b0a002a d37df04b (f86b694b)
[...]
In this case the index used in BPF r3 is the same as in r1
at the time of the call, meaning we fed a pointer as index;
here, it had the value 0xffff808fd7cf0500 which sits in x2.
While I found tail calls to be working in general (also for
hitting the error cases), I noticed the following in the code
emission:
# bpftool p d j i 988
[...]
38: ldr w10, [x1,x10]
3c: cmp w2, w10
40: b.ge 0x000000000000007c <-- signed cmp
44: mov x10, #0x20 // #32
48: cmp x26, x10
4c: b.gt 0x000000000000007c
50: add x26, x26, #0x1
54: mov x10, #0x110 // #272
58: add x10, x1, x10
5c: lsl x11, x2, #3
60: ldr x11, [x10,x11] <-- faulting insn (f86b694b)
64: cbz x11, 0x000000000000007c
[...]
Meaning, the tests passed because commit ddb55992b0 ("arm64:
bpf: implement bpf_tail_call() helper") was using signed compares
instead of unsigned which as a result had the test wrongly passing.
Change this but also the tail call count test both into unsigned
and cap the index as u32. Latter we did as well in 90caccdd8c
("bpf: fix bpf_tail_call() x64 JIT") and is needed in addition here,
too. Tested on HiSilicon Hi1616.
Result after patch:
# bpftool p d j i 268
[...]
38: ldr w10, [x1,x10]
3c: add w2, w2, #0x0
40: cmp w2, w10
44: b.cs 0x0000000000000080
48: mov x10, #0x20 // #32
4c: cmp x26, x10
50: b.hi 0x0000000000000080
54: add x26, x26, #0x1
58: mov x10, #0x110 // #272
5c: add x10, x1, x10
60: lsl x11, x2, #3
64: ldr x11, [x10,x11]
68: cbz x11, 0x0000000000000080
[...]
Fixes: ddb55992b0 ("arm64: bpf: implement bpf_tail_call() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ upstream commit a493a87f38 ]
Implement a retpoline [0] for the BPF tail call JIT'ing that converts
the indirect jump via jmp %rax that is used to make the long jump into
another JITed BPF image. Since this is subject to speculative execution,
we need to control the transient instruction sequence here as well
when CONFIG_RETPOLINE is set, and direct it into a pause + lfence loop.
The latter aligns also with what gcc / clang emits (e.g. [1]).
JIT dump after patch:
# bpftool p d x i 1
0: (18) r2 = map[id:1]
2: (b7) r3 = 0
3: (85) call bpf_tail_call#12
4: (b7) r0 = 2
5: (95) exit
With CONFIG_RETPOLINE:
# bpftool p d j i 1
[...]
33: cmp %edx,0x24(%rsi)
36: jbe 0x0000000000000072 |*
38: mov 0x24(%rbp),%eax
3e: cmp $0x20,%eax
41: ja 0x0000000000000072 |
43: add $0x1,%eax
46: mov %eax,0x24(%rbp)
4c: mov 0x90(%rsi,%rdx,8),%rax
54: test %rax,%rax
57: je 0x0000000000000072 |
59: mov 0x28(%rax),%rax
5d: add $0x25,%rax
61: callq 0x000000000000006d |+
66: pause |
68: lfence |
6b: jmp 0x0000000000000066 |
6d: mov %rax,(%rsp) |
71: retq |
72: mov $0x2,%eax
[...]
* relative fall-through jumps in error case
+ retpoline for indirect jump
Without CONFIG_RETPOLINE:
# bpftool p d j i 1
[...]
33: cmp %edx,0x24(%rsi)
36: jbe 0x0000000000000063 |*
38: mov 0x24(%rbp),%eax
3e: cmp $0x20,%eax
41: ja 0x0000000000000063 |
43: add $0x1,%eax
46: mov %eax,0x24(%rbp)
4c: mov 0x90(%rsi,%rdx,8),%rax
54: test %rax,%rax
57: je 0x0000000000000063 |
59: mov 0x28(%rax),%rax
5d: add $0x25,%rax
61: jmpq *%rax |-
63: mov $0x2,%eax
[...]
* relative fall-through jumps in error case
- plain indirect jump as before
[0] https://support.google.com/faqs/answer/7625886
[1] a31e654fa1
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The backport of upstream commit 45d55e7bac ("x86/apic/vector: Fix off by
one in error path") missed to fixup the legacy interrupt data which is not
longer available upstream.
Handle legacy irq data correctly by clearing the legacy storage to prevent
use after free.
Fixes: 7fd133539289 ("x86/apic/vector: Fix off by one in error path") - 4.4.y
Fixes: c557481a94 ("x86/apic/vector: Fix off by one in error path") - 4.9.y
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18bf3c3ea8 upstream.
Flush indirect branches when switching into a process that marked itself
non dumpable. This protects high value processes like gpg better,
without having too high performance overhead.
If done naïvely, we could switch to a kernel idle thread and then back
to the original process, such as:
process A -> idle -> process A
In such scenario, we do not have to do IBPB here even though the process
is non-dumpable, as we are switching back to the same process after a
hiatus.
To avoid the redundant IBPB, which is expensive, we track the last mm
user context ID. The cost is to have an extra u64 mm context id to track
the last mm we were using before switching to the init_mm used by idle.
Avoiding the extra IBPB is probably worth the extra memory for this
common scenario.
For those cases where tlb_defer_switch_to_init_mm() returns true (non
PCID), lazy tlb will defer switch to init_mm, so we will not be changing
the mm for the process A -> idle -> process A switch. So IBPB will be
skipped for this case.
Thanks to the reviewers and Andy Lutomirski for the suggestion of
using ctx_id which got rid of the problem of mm pointer recycling.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: ak@linux.intel.com
Cc: karahmed@amazon.de
Cc: arjan@linux.intel.com
Cc: torvalds@linux-foundation.org
Cc: linux@dominikbrodowski.net
Cc: peterz@infradead.org
Cc: bp@alien8.de
Cc: luto@kernel.org
Cc: pbonzini@redhat.com
Link: https://lkml.kernel.org/r/1517263487-3708-1-git-send-email-dwmw@amazon.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f39681ed0f upstream.
This adds two new variables to mmu_context_t: ctx_id and tlb_gen.
ctx_id uniquely identifies the mm_struct and will never be reused.
For a given mm_struct (and hence ctx_id), tlb_gen is a monotonic
count of the number of times that a TLB flush has been requested.
The pair (ctx_id, tlb_gen) can be used as an identifier for TLB
flush actions and will be used in subsequent patches to reliably
determine whether all needed TLB flushes have occurred on a given
CPU.
This patch is split out for ease of review. By itself, it has no
real effect other than creating and updating the new variables.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Nadav Amit <nadav.amit@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/413a91c24dab3ed0caa5f4e4d017d87b0857f920.1498751203.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74402055a2 upstream.
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at time.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: 687c276761 ("ARM: dts: Add minimal support for LogicPD Torpedo
DM3730 devkit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84c7efd607 upstream.
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at times.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD DM3730
SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 946fbbc13d upstream.
vmx_vcpu_run() and svm_vcpu_run() are large functions, and giving
branch hints to the compiler can actually make a substantial cycle
difference by keeping the fast path contiguous in memory.
With this optimization, the retpoline-guest/retpoline-host case is
about 50 cycles faster.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: KarimAllah Ahmed <karahmed@amazon.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20180222154318.20361-3-pbonzini@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ecb586bd29 upstream.
Having a paravirt indirect call in the IBRS restore path is not a
good idea, since we are trying to protect from speculative execution
of bogus indirect branch targets. It is also slower, so use
native_wrmsrl() on the vmentry path too.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: KarimAllah Ahmed <karahmed@amazon.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: d28b387fb7
Link: http://lkml.kernel.org/r/20180222154318.20361-2-pbonzini@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67870eb120 upstream.
In banked-sr.c, we use a top-level '__asm__(".arch_extension virt")'
statement to allow compilation of a multi-CPU kernel for ARMv6
and older ARMv7-A that don't normally support access to the banked
registers.
This is considered to be a programming error by the gcc developers
and will no longer work in gcc-8, where we now get a build error:
/tmp/cc4Qy7GR.s:34: Error: Banked registers are not available with this architecture. -- `mrs r3,SP_usr'
/tmp/cc4Qy7GR.s:41: Error: Banked registers are not available with this architecture. -- `mrs r3,ELR_hyp'
/tmp/cc4Qy7GR.s:55: Error: Banked registers are not available with this architecture. -- `mrs r3,SP_svc'
/tmp/cc4Qy7GR.s:62: Error: Banked registers are not available with this architecture. -- `mrs r3,LR_svc'
/tmp/cc4Qy7GR.s:69: Error: Banked registers are not available with this architecture. -- `mrs r3,SPSR_svc'
/tmp/cc4Qy7GR.s:76: Error: Banked registers are not available with this architecture. -- `mrs r3,SP_abt'
Passign the '-march-armv7ve' flag to gcc works, and is ok here, because
we know the functions won't ever be called on pre-ARMv7VE machines.
Unfortunately, older compiler versions (4.8 and earlier) do not understand
that flag, so we still need to keep the asm around.
Backporting to stable kernels (4.6+) is needed to allow those to be built
with future compilers as well.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=84129
Fixes: 33280b4cd1 ("ARM: KVM: Add banked registers save/restore")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8aa36a8dcd upstream.
The MACH_ARMADA_375 and MACH_ARMADA_38X boards select ARM_ERRATA_753970,
but it was renamed to PL310_ERRATA_753970 by commit fa0ce4035d ("ARM:
7162/1: errata: tidy up Kconfig options for PL310 errata workarounds").
Fix the selects to use the new name.
Discovered with the
https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py
script.
Fixes: fa0ce4035d ("ARM: 7162/1: errata: tidy up Kconfig options for
PL310 errata workarounds"
cc: stable@vger.kernel.org
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 028091f82e upstream.
When the Intel Edison module is powered with 3.3V, the reboot command makes
the module stuck. If the module is powered at a greater voltage, like 4.4V
(as the Edison Mini Breakout board does), reboot works OK.
The official Intel Edison BSP sends the IPCMSG_COLD_RESET message to the
SCU by default. The IPCMSG_COLD_BOOT which is used by the upstream kernel
is only sent when explicitely selected on the kernel command line.
Use IPCMSG_COLD_RESET unconditionally which makes reboot work independent
of the power supply voltage.
[ tglx: Massaged changelog ]
Fixes: bda7b072de ("x86/platform/intel-mid: Implement power off sequence")
Signed-off-by: Sebastian Panceac <sebastian@resin.io>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1519810849-15131-1-git-send-email-sebastian@resin.io
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0adb24e03a upstream.
The change to flush_kernel_vmap_range() wasn't sufficient to avoid the
SMP stalls. The problem is some drivers call these routines with
interrupts disabled. Interrupts need to be enabled for flush_tlb_all()
and flush_cache_all() to work. This version adds checks to ensure
interrupts are not disabled before calling routines that need IPI
interrupts. When interrupts are disabled, we now drop into slower code.
The attached change fixes the ordering of cache and TLB flushes in
several cases. When we flush the cache using the existing PTE/TLB
entries, we need to flush the TLB after doing the cache flush. We don't
need to do this when we flush the entire instruction and data caches as
these flushes don't use the existing TLB entries. The same is true for
tmpalias region flushes.
The flush_kernel_vmap_range() and invalidate_kernel_vmap_range()
routines have been updated.
Secondly, we added a new purge_kernel_dcache_range_asm() routine to
pacache.S and use it in invalidate_kernel_vmap_range(). Nominally,
purges are faster than flushes as the cache lines don't have to be
written back to memory.
Hopefully, this is sufficient to resolve the remaining problems due to
cache speculation. So far, testing indicates that this is the case. I
did work up a patch using tmpalias flushes, but there is a performance
hit because we need the physical address for each page, and we also need
to sequence access to the tmpalias flush code. This increases the
probability of stalls.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebabcf17bc upstream.
GCC7 is a bit too eager to generate suboptimal __multi3 calls (128bit
multiply with 128bit result) for MIPS64r6 builds, even in code which
doesn't explicitly use 128bit types, such as the following:
unsigned long func(unsigned long a, unsigned long b)
{
return a > (~0UL) / b;
}
Which GCC rearanges to:
return (unsigned __int128)a * (unsigned __int128)b > 0xffffffffffffffff;
Therefore implement __multi3, but only for MIPS64r6 with GCC7 as under
normal circumstances we wouldn't expect any calls to __multi3 to be
generated from kernel code.
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: James Hogan <jhogan@kernel.org>
Tested-by: Waldemar Brodkorb <wbx@openadk.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maciej W. Rozycki <macro@mips.com>
Cc: Matthew Fortune <matthew.fortune@mips.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17890/
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 45ee9d5e97 ("KVM: arm/arm64: Check pagesize when allocating a
hugepage at Stage 2") lost the check for PMD_SIZE during the backport
to 4.9.
Fix this by correcting the condition to detect hugepages during stage
2 allocation.
Fixes: 45ee9d5e97 ("KVM: arm/arm64: Check pagesize when allocating a hugepage at Stage 2")
Reported-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 195e2addbc ]
The 'sh_eth' driver's probe() method would fail on the SolutionEngine7710
board and crash on SolutionEngine7712 board as the platform code is
hopelessly behind the driver's platform data -- it passes the PHY address
instead of 'struct sh_eth_plat_data *'; pass the latter to the driver in
order to fix the bug...
Fixes: 71557a37ad ("[netdrvr] sh_eth: Add SH7619 support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 506e8a9126 ]
dtc warns about two 'clocks' properties that have an extraneous '1'
at the end:
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a:clocks[1])
Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2190000/sgtl5000@a
arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2190000/sgtl5000@a:clocks[1])
The clocks that get referenced here are fixed-rate, so they do not
take any argument, and dtc interprets the next cell as a phandle, which
is invalid.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ca26cffa4e ]
Up to f5caf621ee ("x86/asm: Fix inline asm call constraints for Clang")
we were able to use x86 headers to build to the 'bpf' clang target, as
done by the BPF code in tools/perf/.
With that commit, we ended up with following failure for 'perf test LLVM', this
is because "clang ... -target bpf ..." fails since 4.0 does not have bpf inline
asm support and 6.0 does not recognize the register 'esp', fix it by guarding
that part with an #ifndef __BPF__, that is defined by clang when building to
the "bpf" target.
# perf test -v LLVM
37: LLVM search and compile :
37.1: Basic BPF llvm compile :
--- start ---
test child forked, pid 25526
Kernel build dir is set to /lib/modules/4.14.0+/build
set env: KBUILD_DIR=/lib/modules/4.14.0+/build
unset env: KBUILD_OPTS
include option is set to -nostdinc -isystem /usr/lib/gcc/x86_64-redhat-linux/7/include -I/home/acme/git/linux/arch/x86/include -I./arch/x86/include/generated -I/home/acme/git/linux/include -I./include -I/home/acme/git/linux/arch/x86/include/uapi -I./arch/x86/include/generated/uapi -I/home/acme/git/linux/include/uapi -I./include/generated/uapi -include /home/acme/git/linux/include/linux/kconfig.h
set env: NR_CPUS=4
set env: LINUX_VERSION_CODE=0x40e00
set env: CLANG_EXEC=/usr/local/bin/clang
set env: CLANG_OPTIONS=-xc
set env: KERNEL_INC_OPTIONS= -nostdinc -isystem /usr/lib/gcc/x86_64-redhat-linux/7/include -I/home/acme/git/linux/arch/x86/include -I./arch/x86/include/generated -I/home/acme/git/linux/include -I./include -I/home/acme/git/linux/arch/x86/include/uapi -I./arch/x86/include/generated/uapi -I/home/acme/git/linux/include/uapi -I./include/generated/uapi -include /home/acme/git/linux/include/linux/kconfig.h
set env: WORKING_DIR=/lib/modules/4.14.0+/build
set env: CLANG_SOURCE=-
llvm compiling command template: echo '/*
* bpf-script-example.c
* Test basic LLVM building
*/
#ifndef LINUX_VERSION_CODE
# error Need LINUX_VERSION_CODE
# error Example: for 4.2 kernel, put 'clang-opt="-DLINUX_VERSION_CODE=0x40200" into llvm section of ~/.perfconfig'
#endif
#define BPF_ANY 0
#define BPF_MAP_TYPE_ARRAY 2
#define BPF_FUNC_map_lookup_elem 1
#define BPF_FUNC_map_update_elem 2
static void *(*bpf_map_lookup_elem)(void *map, void *key) =
(void *) BPF_FUNC_map_lookup_elem;
static void *(*bpf_map_update_elem)(void *map, void *key, void *value, int flags) =
(void *) BPF_FUNC_map_update_elem;
struct bpf_map_def {
unsigned int type;
unsigned int key_size;
unsigned int value_size;
unsigned int max_entries;
};
#define SEC(NAME) __attribute__((section(NAME), used))
struct bpf_map_def SEC("maps") flip_table = {
.type = BPF_MAP_TYPE_ARRAY,
.key_size = sizeof(int),
.value_size = sizeof(int),
.max_entries = 1,
};
SEC("func=SyS_epoll_wait")
int bpf_func__SyS_epoll_wait(void *ctx)
{
int ind =0;
int *flag = bpf_map_lookup_elem(&flip_table, &ind);
int new_flag;
if (!flag)
return 0;
/* flip flag and store back */
new_flag = !*flag;
bpf_map_update_elem(&flip_table, &ind, &new_flag, BPF_ANY);
return new_flag;
}
char _license[] SEC("license") = "GPL";
int _version SEC("version") = LINUX_VERSION_CODE;
' | $CLANG_EXEC -D__KERNEL__ -D__NR_CPUS__=$NR_CPUS -DLINUX_VERSION_CODE=$LINUX_VERSION_CODE $CLANG_OPTIONS $KERNEL_INC_OPTIONS -Wno-unused-value -Wno-pointer-sign -working-directory $WORKING_DIR -c "$CLANG_SOURCE" -target bpf -O2 -o -
test child finished with 0
---- end ----
LLVM search and compile subtest 0: Ok
37.2: kbuild searching :
--- start ---
test child forked, pid 25950
Kernel build dir is set to /lib/modules/4.14.0+/build
set env: KBUILD_DIR=/lib/modules/4.14.0+/build
unset env: KBUILD_OPTS
include option is set to -nostdinc -isystem /usr/lib/gcc/x86_64-redhat-linux/7/include -I/home/acme/git/linux/arch/x86/include -I./arch/x86/include/generated -I/home/acme/git/linux/include -I./include -I/home/acme/git/linux/arch/x86/include/uapi -I./arch/x86/include/generated/uapi -I/home/acme/git/linux/include/uapi -I./include/generated/uapi -include /home/acme/git/linux/include/linux/kconfig.h
set env: NR_CPUS=4
set env: LINUX_VERSION_CODE=0x40e00
set env: CLANG_EXEC=/usr/local/bin/clang
set env: CLANG_OPTIONS=-xc
set env: KERNEL_INC_OPTIONS= -nostdinc -isystem /usr/lib/gcc/x86_64-redhat-linux/7/include -I/home/acme/git/linux/arch/x86/include -I./arch/x86/include/generated -I/home/acme/git/linux/include -I./include -I/home/acme/git/linux/arch/x86/include/uapi -I./arch/x86/include/generated/uapi -I/home/acme/git/linux/include/uapi -I./include/generated/uapi -include /home/acme/git/linux/include/linux/kconfig.h
set env: WORKING_DIR=/lib/modules/4.14.0+/build
set env: CLANG_SOURCE=-
llvm compiling command template: echo '/*
* bpf-script-test-kbuild.c
* Test include from kernel header
*/
#ifndef LINUX_VERSION_CODE
# error Need LINUX_VERSION_CODE
# error Example: for 4.2 kernel, put 'clang-opt="-DLINUX_VERSION_CODE=0x40200" into llvm section of ~/.perfconfig'
#endif
#define SEC(NAME) __attribute__((section(NAME), used))
#include <uapi/linux/fs.h>
#include <uapi/asm/ptrace.h>
SEC("func=vfs_llseek")
int bpf_func__vfs_llseek(void *ctx)
{
return 0;
}
char _license[] SEC("license") = "GPL";
int _version SEC("version") = LINUX_VERSION_CODE;
' | $CLANG_EXEC -D__KERNEL__ -D__NR_CPUS__=$NR_CPUS -DLINUX_VERSION_CODE=$LINUX_VERSION_CODE $CLANG_OPTIONS $KERNEL_INC_OPTIONS -Wno-unused-value -Wno-pointer-sign -working-directory $WORKING_DIR -c "$CLANG_SOURCE" -target bpf -O2 -o -
In file included from <stdin>:12:
In file included from /home/acme/git/linux/arch/x86/include/uapi/asm/ptrace.h:5:
In file included from /home/acme/git/linux/include/linux/compiler.h:242:
In file included from /home/acme/git/linux/arch/x86/include/asm/barrier.h:5:
In file included from /home/acme/git/linux/arch/x86/include/asm/alternative.h:10:
/home/acme/git/linux/arch/x86/include/asm/asm.h:145:50: error: unknown register name 'esp' in asm
register unsigned long current_stack_pointer asm(_ASM_SP);
^
/home/acme/git/linux/arch/x86/include/asm/asm.h:44:18: note: expanded from macro '_ASM_SP'
#define _ASM_SP __ASM_REG(sp)
^
/home/acme/git/linux/arch/x86/include/asm/asm.h:27:32: note: expanded from macro '__ASM_REG'
#define __ASM_REG(reg) __ASM_SEL_RAW(e##reg, r##reg)
^
/home/acme/git/linux/arch/x86/include/asm/asm.h:18:29: note: expanded from macro '__ASM_SEL_RAW'
# define __ASM_SEL_RAW(a,b) __ASM_FORM_RAW(a)
^
/home/acme/git/linux/arch/x86/include/asm/asm.h:11:32: note: expanded from macro '__ASM_FORM_RAW'
# define __ASM_FORM_RAW(x) #x
^
<scratch space>:4:1: note: expanded from here
"esp"
^
1 error generated.
ERROR: unable to compile -
Hint: Check error message shown above.
Hint: You can also pre-compile it into .o using:
clang -target bpf -O2 -c -
with proper -I and -D options.
Failed to compile test case: 'kbuild searching'
test child finished with -1
---- end ----
LLVM search and compile subtest 1: FAILED!
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Yonghong Song <yhs@fb.com>
Link: https://lkml.kernel.org/r/20171128175948.GL3298@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 36b0cb84ee ]
An additional 'ip' will be pushed to the stack, for restoring the
DACR later, if CONFIG_CPU_SW_DOMAIN_PAN defined.
However, the fixup still get the err_ptr by add #8*4 to sp, which
results in the fact that the code area pointed by the LR will be
overwritten, or the kernel will crash if CONFIG_DEBUG_RODATA is enabled.
This patch fixes the stack mismatch.
Fixes: a5e090acbf ("ARM: software-based priviledged-no-access support")
Signed-off-by: Lvqiang Huang <Lvqiang.Huang@spreadtrum.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e1eb3fa00 upstream.
At entry userspace may have (maliciously) populated the extra registers
outside the syscall calling convention with arbitrary values that could
be useful in a speculative execution (Spectre style) attack.
Clear these registers to minimize the kernel's attack surface.
Note, this only clears the extra registers and not the unused
registers for syscalls less than 6 arguments, since those registers are
likely to be clobbered well before their values could be put to use
under speculation.
Note, Linus found that the XOR instructions can be executed with
minimized cost if interleaved with the PUSH instructions, and Ingo's
analysis found that R10 and R11 should be included in the register
clearing beyond the typical 'extra' syscall calling convention
registers.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/151787988577.7847.16733592218894189003.stgit@dwillia2-desk3.amr.corp.intel.com
[ Made small improvements to the changelog and the code comments. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85c615eb52 upstream.
GCC-8 shows a warning for the x86 oprofile code that copies per-CPU
data from CPU 0 to all other CPUs, which when building a non-SMP
kernel turns into a memcpy() with identical source and destination
pointers:
arch/x86/oprofile/nmi_int.c: In function 'mux_clone':
arch/x86/oprofile/nmi_int.c:285:2: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
memcpy(per_cpu(cpu_msrs, cpu).multiplex,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
per_cpu(cpu_msrs, 0).multiplex,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(struct op_msr) * model->num_virt_counters);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/x86/oprofile/nmi_int.c: In function 'nmi_setup':
arch/x86/oprofile/nmi_int.c:466:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
arch/x86/oprofile/nmi_int.c:470:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
I have analyzed a number of such warnings now: some are valid and the
GCC warning is welcome. Others turned out to be false-positives, and
GCC was changed to not warn about those any more. This is a corner case
that is a false-positive but the GCC developers feel it's better to keep
warning about it.
In this case, it seems best to work around it by telling GCC
a little more clearly that this code path is never hit with
an IS_ENABLED() configuration check.
Cc:stable as we also want old kernels to build cleanly with GCC-8.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Sebor <msebor@gcc.gnu.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Richter <rric@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: oprofile-list@lists.sf.net
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20180220205826.2008875-1-arnd@arndb.de
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=84095
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ac5a11dc6 upstream.
Xtensa memory initialization code frees high memory pages without
checking whether they are in the reserved memory regions or not. That
results in invalid value of totalram_pages and duplicate page usage by
CMA and highmem. It produces a bunch of BUGs at startup looking like
this:
BUG: Bad page state in process swapper pfn:70800
page:be60c000 count:0 mapcount:-127 mapping: (null) index:0x1
flags: 0x80000000()
raw: 80000000 00000000 00000001 ffffff80 00000000 be60c014 be60c014 0000000a
page dumped because: nonzero mapcount
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Tainted: G B 4.16.0-rc1-00015-g7928b2cbe55b-dirty #23
Stack:
bd839d33 00000000 00000018 ba97b64c a106578c bd839d70 be60c000 00000000
a1378054 bd86a000 00000003 ba97b64c a1066166 bd839da0 be60c000 ffe00000
a1066b58 bd839dc0 be504000 00000000 000002f4 bd838000 00000000 0000001e
Call Trace:
[<a1065734>] bad_page+0xac/0xd0
[<a106578c>] free_pages_check_bad+0x34/0x4c
[<a1066166>] __free_pages_ok+0xae/0x14c
[<a1066b58>] __free_pages+0x30/0x64
[<a1365de5>] init_cma_reserved_pageblock+0x35/0x44
[<a13682dc>] cma_init_reserved_areas+0xf4/0x148
[<a10034b8>] do_one_initcall+0x80/0xf8
[<a1361c16>] kernel_init_freeable+0xda/0x13c
[<a125b59d>] kernel_init+0x9/0xd0
[<a1004304>] ret_from_kernel_thread+0xc/0x18
Only free high memory pages that are not reserved.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcdde302b8 upstream
- Expose all invalidation types to the L1
- Reject invvpid instruction, if L1 passed zero vpid value to single
context invalidations
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Tested-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[jwang: port to 4.4]
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63f3ac4813 upstream
- Remove VMX_EPT_EXTENT_INDIVIDUAL_ADDR, since there is no such type of
EPT invalidation
- Add missing VPID types names
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Tested-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[jwang: port to 4.4]
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a6e7c3981 upstream.
qemu-system-x86-8600 [004] d..1 7205.687530: kvm_entry: vcpu 2
qemu-system-x86-8600 [004] .... 7205.687532: kvm_exit: reason EXCEPTION_NMI rip 0xffffffffa921297d info ffffeb2c0e44e018 80000b0e
qemu-system-x86-8600 [004] .... 7205.687532: kvm_page_fault: address ffffeb2c0e44e018 error_code 0
qemu-system-x86-8600 [004] .... 7205.687620: kvm_try_async_get_page: gva = 0xffffeb2c0e44e018, gfn = 0x427e4e
qemu-system-x86-8600 [004] .N.. 7205.687628: kvm_async_pf_not_present: token 0x8b002 gva 0xffffeb2c0e44e018
kworker/4:2-7814 [004] .... 7205.687655: kvm_async_pf_completed: gva 0xffffeb2c0e44e018 address 0x7fcc30c4e000
qemu-system-x86-8600 [004] .... 7205.687703: kvm_async_pf_ready: token 0x8b002 gva 0xffffeb2c0e44e018
qemu-system-x86-8600 [004] d..1 7205.687711: kvm_entry: vcpu 2
After running some memory intensive workload in guest, I catch the kworker
which completes the GUP too quickly, and queues an "Page Ready" #PF exception
after the "Page not Present" exception before the next vmentry as the above
trace which will result in #DF injected to guest.
This patch fixes it by clearing the queue for "Page not Present" if "Page Ready"
occurs before the next vmentry since the GUP has already got the required page
and shadow page table has already been fixed by "Page Ready" handler.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Fixes: 7c90705bf2 ("KVM: Inject asynchronous page fault into a PV guest if page is swapped out.")
[Changed indentation and added clearing of injected. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[port from upstream v4.14-rc1, Don't assign to kvm_queued_exception::injected or
x86_exception::async_page_fault]
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dac6ca243c upstream.
With CONFIG_DEBUG_PREEMPT enabled, I get:
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1
caller is debug_smp_processor_id
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.12.0-rc2+ #2
Call Trace:
dump_stack
check_preemption_disabled
debug_smp_processor_id
save_microcode_in_initrd_amd
? microcode_init
save_microcode_in_initrd
...
because, well, it says it above, we're using smp_processor_id() in
preemptible code.
But passing the CPU number is not really needed. It is only used to
determine whether we're on the BSP, and, if so, to save the microcode
patch for early loading.
[ We don't absolutely need to do it on the BSP but we do that
customarily there. ]
Instead, convert that function parameter to a boolean which denotes
whether the patch should be saved or not, thereby avoiding the use of
smp_processor_id() in preemptible code.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170528200414.31305-1-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[arnd: rebased to 4.9, after running into warning:
arch/x86/kernel/cpu/microcode/amd.c:881:30: self-comparison always evaluates to true]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lars Ivar Miljeteig