The test application controls the OTG pin itself,
not via the usb OTG driver. A change between kern
4.1 and 4.9 causes the regulator to take the
gpio pin even if there are no references to it.
This commit removes the vbus gpio from the
driver, so that the test application works again.
There are two flavours of the device tree today, one
for the main application and one for the testing
application used in the factory. This patch gathers
them both in the same branch, to be able to use the
same kernel for both factory and end user.
Add a default config based on imx6 default config
Update our default config
Update defconfig
Clean out unused stuff from defconfig
Re-add IMX serial to defconfig
Re-enable large files support
Enable PXPv2 in defconfig
Disable auto update mode in EPDC driver
Use correct poweroff driver
defconfig: switch to interactive cpu scheduler, enable cpu idle
defconfig: disable cyttsp debug output
defconfig: enable usb gadget support
defconfig: enable fsl_otp, remove some debug output
defconfig: Enable brcmfmac
defconfig: add reset controller for wifi for powering it up
defconfig: power management, support more USB devices, gpio charger support, CAAM support for RNG
defconfig: enable nbd for vfatbuse, enable reset by syscon, fuck around with spi
defconfig enable f2fs support
defconfig: Disable busfreq
defconfig: re-enable cpu frequency scaling
defconfig: use ethernet gadget by default
commit bcdde302b8 upstream
- Expose all invalidation types to the L1
- Reject invvpid instruction, if L1 passed zero vpid value to single
context invalidations
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Tested-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[jwang: port to 4.4]
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63f3ac4813 upstream
- Remove VMX_EPT_EXTENT_INDIVIDUAL_ADDR, since there is no such type of
EPT invalidation
- Add missing VPID types names
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Tested-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[jwang: port to 4.4]
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a6e7c3981 upstream.
qemu-system-x86-8600 [004] d..1 7205.687530: kvm_entry: vcpu 2
qemu-system-x86-8600 [004] .... 7205.687532: kvm_exit: reason EXCEPTION_NMI rip 0xffffffffa921297d info ffffeb2c0e44e018 80000b0e
qemu-system-x86-8600 [004] .... 7205.687532: kvm_page_fault: address ffffeb2c0e44e018 error_code 0
qemu-system-x86-8600 [004] .... 7205.687620: kvm_try_async_get_page: gva = 0xffffeb2c0e44e018, gfn = 0x427e4e
qemu-system-x86-8600 [004] .N.. 7205.687628: kvm_async_pf_not_present: token 0x8b002 gva 0xffffeb2c0e44e018
kworker/4:2-7814 [004] .... 7205.687655: kvm_async_pf_completed: gva 0xffffeb2c0e44e018 address 0x7fcc30c4e000
qemu-system-x86-8600 [004] .... 7205.687703: kvm_async_pf_ready: token 0x8b002 gva 0xffffeb2c0e44e018
qemu-system-x86-8600 [004] d..1 7205.687711: kvm_entry: vcpu 2
After running some memory intensive workload in guest, I catch the kworker
which completes the GUP too quickly, and queues an "Page Ready" #PF exception
after the "Page not Present" exception before the next vmentry as the above
trace which will result in #DF injected to guest.
This patch fixes it by clearing the queue for "Page not Present" if "Page Ready"
occurs before the next vmentry since the GUP has already got the required page
and shadow page table has already been fixed by "Page Ready" handler.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Fixes: 7c90705bf2 ("KVM: Inject asynchronous page fault into a PV guest if page is swapped out.")
[Changed indentation and added clearing of injected. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[port from upstream v4.14-rc1, Don't assign to kvm_queued_exception::injected or
x86_exception::async_page_fault]
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dac6ca243c upstream.
With CONFIG_DEBUG_PREEMPT enabled, I get:
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1
caller is debug_smp_processor_id
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.12.0-rc2+ #2
Call Trace:
dump_stack
check_preemption_disabled
debug_smp_processor_id
save_microcode_in_initrd_amd
? microcode_init
save_microcode_in_initrd
...
because, well, it says it above, we're using smp_processor_id() in
preemptible code.
But passing the CPU number is not really needed. It is only used to
determine whether we're on the BSP, and, if so, to save the microcode
patch for early loading.
[ We don't absolutely need to do it on the BSP but we do that
customarily there. ]
Instead, convert that function parameter to a boolean which denotes
whether the patch should be saved or not, thereby avoiding the use of
smp_processor_id() in preemptible code.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170528200414.31305-1-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[arnd: rebased to 4.9, after running into warning:
arch/x86/kernel/cpu/microcode/amd.c:881:30: self-comparison always evaluates to true]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12f043ff2b upstream.
With 4 levels of 16KB pages, we get this warning about the fact that we are
copying a whole page into an array that is declared as having only two pointers
for the top level of the page table:
arch/arm64/mm/mmu.c: In function 'paging_init':
arch/arm64/mm/mmu.c:528:2: error: 'memcpy' writing 16384 bytes into a region of size 16 overflows the destination [-Werror=stringop-overflow=]
This is harmless since we actually reserve a whole page in the definition of the
array that comes from, and just the extern declaration is short. The pgdir
is initialized to zero either way, so copying the actual entries here seems
like the best solution.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
[slightly adapted to apply on 4.9]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 900a9020af upstream.
The sunxi clk driver causes a link error when the reset controller
subsystem is disabled:
drivers/clk/built-in.o: In function `sun4i_ve_clk_setup':
:(.init.text+0xd040): undefined reference to `reset_controller_register'
drivers/clk/built-in.o: In function `sun4i_a10_display_init':
:(.init.text+0xe5e0): undefined reference to `reset_controller_register'
drivers/clk/built-in.o: In function `sunxi_usb_clk_setup':
:(.init.text+0x10074): undefined reference to `reset_controller_register'
We already force it to be enabled on arm32 and some other arm64 platforms,
but not on arm64/sunxi. This adds the respective Kconfig statements to
also select it here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[arnd: manually rebased to 4.9]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e42eef4ba3 upstream.
The rework of the posted interrupt handling broke building without
support for the local APIC:
ERROR: "boot_cpu_physical_apicid" [arch/x86/kvm/kvm-intel.ko] undefined!
That configuration is probably not particularly useful anyway, so
we can avoid the randconfig failures by adding a Kconfig dependency.
Fixes: 8b306e2f3c ("KVM: VMX: avoid double list add with VT-d posted interrupts")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ba5b5ea7d upstream.
GCC complains about unused variable 'vma' in mark_screen_rdonly() if THP is
disabled:
arch/x86/kernel/vm86_32.c: In function ‘mark_screen_rdonly’:
arch/x86/kernel/vm86_32.c:180:26: warning: unused variable ‘vma’
[-Wunused-variable]
struct vm_area_struct *vma = find_vma(mm, 0xA0000);
That's silly. pmd_trans_huge() resolves to 0 when THP is disabled, so the
whole block should be eliminated.
Moving the variable declaration outside the if() block shuts GCC up.
Reported-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Tested-by: Borislav Petkov <bp@suse.de>
Cc: Carlos O'Donell <carlos@redhat.com>
Link: http://lkml.kernel.org/r/20170213125228.63645-1-kirill.shutemov@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d689c64d18 upstream.
The IOSF_MBI option requires PCI support, without it we get a harmless
Kconfig warning when it gets selected by PUNIT_ATOM_DEBUG:
warning: (X86_INTEL_LPSS && SND_SST_IPC_ACPI && MMC_SDHCI_ACPI && PUNIT_ATOM_DEBUG) selects IOSF_MBI which has unmet direct dependencies (PCI)
This adds another dependency to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170719125310.2487451-8-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d460131dd5 upstream.
Every kernel build on x86 will result in some output:
Setup is 13084 bytes (padded to 13312 bytes).
System is 4833 kB
CRC 6d35fa35
Kernel: arch/x86/boot/bzImage is ready (#2)
This shuts it up, so that 'make -s' is truely silent as long as
everything works. Building without '-s' should produce unchanged
output.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170719125310.2487451-6-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75e2f0a6b1 upstream.
When building the kernel with "make EXTRA_CFLAGS=...", this overrides
the "PARANOID" preprocessor macro defined in arch/x86/math-emu/Makefile,
and we run into a build warning:
arch/x86/math-emu/reg_compare.c: In function ‘compare_i_st_st’:
arch/x86/math-emu/reg_compare.c:254:6: error: ‘f’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This fixes the implementation to work correctly even without the PARANOID
flag, and also fixes the Makefile to not use the EXTRA_CFLAGS variable
but instead use the ccflags-y variable in the Makefile that is meant
for this purpose.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Bill Metzenthen <billm@melbpc.org.au>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170719125310.2487451-3-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f13d52cb3f upstream.
This mirrors commit e9c38ceba8 ("ARM: 8455/1: define __BUG as
asm(BUG_INSTR) without CONFIG_BUG") to make the behavior of
arm64 consistent with arm and x86, and avoids lots of warnings in
randconfig builds, such as:
kernel/seccomp.c: In function '__seccomp_filter':
kernel/seccomp.c:666:1: error: no return statement in function returning non-void [-Werror=return-type]
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4b2ac63b0 upstream.
... and get rid of the annoying:
arch/x86/kernel/cpu/mcheck/mce-inject.c:97:13: warning: ‘mce_irq_ipi’ defined but not used [-Wunused-function]
when doing randconfig builds.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Yazen Ghannam <Yazen.Ghannam@amd.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170123183514.13356-2-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11d8b05855 upstream.
The intialization function checks for various failure scenarios, but
unfortunately the compiler gets a little confused about the possible
combinations, leading to a false-positive build warning when
-Wmaybe-uninitialized is set:
arch/x86/events/core.c: In function ‘init_hw_perf_events’:
arch/x86/events/core.c:264:3: warning: ‘reg_fail’ may be used uninitialized in this function [-Wmaybe-uninitialized]
arch/x86/events/core.c:264:3: warning: ‘val_fail’ may be used uninitialized in this function [-Wmaybe-uninitialized]
pr_err(FW_BUG "the BIOS has corrupted hw-PMU resources (MSR %x is %Lx)\n",
We can't actually run into this case, so this shuts up the warning
by initializing the variables to a known-invalid state.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170719125310.2487451-2-arnd@arndb.de
Link: https://patchwork.kernel.org/patch/9392595/
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdcb1aefc5 upstream.
The fallback RFI flush is used when firmware does not provide a way
to flush the cache. It's a "displacement flush" that evicts useful
data by displacing it with an uninteresting buffer.
The flush has to take care to work with implementation specific cache
replacment policies, so the recipe has been in flux. The initial
slow but conservative approach is to touch all lines of a congruence
class, with dependencies between each load. It has since been
determined that a linear pattern of loads without dependencies is
sufficient, and is significantly faster.
Measuring the speed of a null syscall with RFI fallback flush enabled
gives the relative improvement:
P8 - 1.83x
P9 - 1.75x
The flush also becomes simpler and more adaptable to different cache
geometries.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Backport to 4.9]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 222f20f140 upstream.
This commit does simple conversions of rfi/rfid to the new macros that
include the expected destination context. By simple we mean cases
where there is a single well known destination context, and it's
simply a matter of substituting the instruction for the appropriate
macro.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Backport to 4.9, use RFI_TO_KERNEL in idle_book3s.S]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The back port of commit c7305645eb ("powerpc/64s: Convert
slb_miss_common to use RFI_TO_USER/KERNEL") missed a hunk needed to
restore cr6.
Fixes: 48cc95d4e4 ("powerpc/64s: Convert slb_miss_common to use RFI_TO_USER/KERNEL")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d60ce384d ]
If something calls ioremap() with an address not aligned to PAGE_SIZE, the
returned address might be not aligned as well. This led to a probe
registered on exactly the returned address, but the entire page was armed
for mmiotracing.
On calling iounmap() the address passed to unregister_kmmio_probe() was
PAGE_SIZE aligned by the caller leading to a complete freeze of the
machine.
We should always page align addresses while (un)registerung mappings,
because the mmiotracer works on top of pages, not mappings. We still keep
track of the probes based on their real addresses and lengths though,
because the mmiotrace still needs to know what are mapped memory regions.
Also move the call to mmiotrace_iounmap() prior page aligning the address,
so that all probes are unregistered properly, otherwise the kernel ends up
failing memory allocations randomly after disabling the mmiotracer.
Tested-by: Lyude <lyude@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Acked-by: Pekka Paalanen <ppaalanen@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: nouveau@lists.freedesktop.org
Link: http://lkml.kernel.org/r/20171127075139.4928-1-kherbst@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d364b038bc ]
Looks like the interrupt property is missing the controller and level
information causing:
Warning (interrupts_property): interrupts size is (4), expected multiple
of 12 in /ocp/elm@48078000
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5aa04b3eb6 ]
When user tries to group imc (In-Memory Collections) event with
normal event, (sometime) kernel crashes with following log:
Faulting instruction address: 0x00000000
[link register ] c00000000010ce88 power_check_constraints+0x128/0x980
...
c00000000010e238 power_pmu_event_init+0x268/0x6f0
c0000000002dc60c perf_try_init_event+0xdc/0x1a0
c0000000002dce88 perf_event_alloc+0x7b8/0xac0
c0000000002e92e0 SyS_perf_event_open+0x530/0xda0
c00000000000b004 system_call+0x38/0xe0
'event_base' field of 'struct hw_perf_event' is used as flags for
normal hw events and used as memory address for imc events. While
grouping these two types of events, collect_events() tries to
interpret imc 'event_base' as a flag, which causes a corruption
resulting in a crash.
Consider only those events which belongs to 'perf_hw_context' in
collect_events().
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Reviewed-By: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 969de0988b ]
Commit be7635e728 ("arch, ftrace: for KASAN put hard/soft IRQ entries
into separate sections") added a new linker section, SOFTIRQENTRY_TEXT,
to the linker scripts for most architectures. It didn't add it to any of
the linker scripts for the m68k architecture. This was not really a problem
because it is only defined if either of CONFIG_FUNCTION_GRAPH_TRACER or
CONFIG_KASAN are enabled - which can never be true for m68k.
However commit 229a718605 ("irq: Make the irqentry text section
unconditional") means that SOFTIRQENTRY_TEXT is now always defined. So on
m68k we now end up with a separate ELF section for .softirqentry.text
instead of it being part of the .text section. On some m68k targets in some
configurations this can also cause a fatal link error:
LD vmlinux
/usr/local/bin/../m68k-uclinux/bin/ld.real: section .softirqentry.text loaded at [0000000010de10c0,0000000010de12dd] overlaps section .rodata loaded at [0000000010de10c0,0000000010e0fd67]
To fix add in the missing SOFTIRQENTRY_TEXT section into the m68k linker
scripts. I noticed that m68k is also missing the IRQENTRY_TEXT section,
so this patch also adds an entry for that too.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ca41e24451 ]
The DMA binding for eDMA needs 2 parameters, not 1.
The second, missing parameter is the tptc to be used for the channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd7594ac32 ]
The pin assignment for the wl127x interrupt was incorrect. I am
not sure how this every worked. This also eliminates a conflict with
the SMC911x ethernet driver and properly moves pinmuxes for the
related gpio to omap3_pmx_wkup from omap3_pmx_core.
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3c18bbf3d1 ]
This patch fixes and issue where the NAND and GPMC based ethernet
controller stopped working. This also updates the GPMC settings
to be consistent with the Logic PD Torpedo development from the
commit listed above.
Fixes: 44e4716499 ("ARM: dts: omap3: Fix NAND device nodes")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cf87634c8b ]
There's been a reproducable USB OHCI/EHCI cpuidle related hang on omap4
for a while that happens after about 20 - 40 minutes on an idle system
with some data feeding device being connected, like a USB GPS device or
a cellular modem.
This issue happens in cpuidle states C2 and C3 and does not happen if
cpuidle is limited to C1 state only. The symptoms are that the whole
system hangs and never wakes up from idle, and if a watchdog is
configured the system reboots after a while.
Turns out that OHCI/EHCI devices on omap4 are trying to use the GIC
interrupt controller directly as a parent instead of the WUGEN. We
need to pass the interrupts through WUGEN to GIC to provide the wakeup
events for the processor.
Let's fix the issue by removing the gic interrupt-parent and use the
default interrupt-parent wakeupgen instead. Note that omap5.dtsi had
this already fixes earlier by commit 7136d457f3 ("ARM: omap: convert
wakeupgen to stacked domains") but we somehow missed omap4 at that
point.
Fixes: 7136d457f3 ("ARM: omap: convert wakeupgen to stacked domains")
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b6d6af7226 ]
Referring TRM Am335X series:
http://www.ti.com/lit/ug/spruh73p/spruh73p.pdf
The LastPowerStateEntered bitfield is present only for PM_CEFUSE
domain. This is not present in any of the other power domains. Hence
remove the generic am33xx_pwrdm_read_prev_pwrst hook which wrongly
reads the reserved bit fields for all the other power domains.
Reading the reserved bits leads to wrongly interpreting the low
power transitions for various power domains that do not have the
LastPowerStateEntered field. The pm debug counters values are wrong
currently as we are incrementing them based on the reserved bits.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d09220a887 ]
With the CMA changes from Joonsoo Kim <iamjoonsoo.kim@lge.com>, it
was noticed that n900 stopped booting. After investigating it turned
out that n900 save_secure_ram_context does some whacky virtual to
physical address translation for the SRAM data address.
As we now only have minimal parts of omap3 idle code copied to SRAM,
running save_secure_ram_context() in SRAM is not needed. It only gets
called on PM init. And it seems there's no need to ever call this from
SRAM idle code.
So let's just keep save_secure_ram_context() in DDR, and pass it the
physical address of the parameters. We can do everything else in
omap-secure.c like we already do for other secure code.
And since we don't have any documentation, I still have no clue what
the values for 0, 1 and 1 for the parameters might be. If somebody has
figured it out, please do send a patch to add some comments.
Debugged-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acbf76ee05 upstream.
dtc complains about the lack of #coolin-cells properties for the
CPU nodes that are referred to as "cooling-device":
arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@0 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@0:cooling-device[0])
arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@100 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@1:cooling-device[0])
Apparently this property must be '<2>' to match the binding.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
[arnd: backported to 4.15]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a21b4c10c7 upstream.
Without this tag, we get a build warning:
WARNING: modpost: missing MODULE_LICENSE() in arch/arm/common/bL_switcher_dummy_if.o
For completeness, I'm also adding author and description fields.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a208fa8f33 upstream.
We need to consistently enforce that keyed hashes cannot be used without
setting the key. To do this we need a reliable way to determine whether
a given hash algorithm is keyed or not. AF_ALG currently does this by
checking for the presence of a ->setkey() method. However, this is
actually slightly broken because the CRC-32 algorithms implement
->setkey() but can also be used without a key. (The CRC-32 "key" is not
actually a cryptographic key but rather represents the initial state.
If not overridden, then a default initial state is used.)
Prepare to fix this by introducing a flag CRYPTO_ALG_OPTIONAL_KEY which
indicates that the algorithm has a ->setkey() method, but it is not
required to be called. Then set it on all the CRC-32 algorithms.
The same also applies to the Adler-32 implementation in Lustre.
Also, the cryptd and mcryptd templates have to pass through the flag
from their underlying algorithm.
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efdab99281 upstream.
syzkaller reported:
WARNING: CPU: 0 PID: 12927 at arch/x86/kernel/traps.c:780 do_debug+0x222/0x250
CPU: 0 PID: 12927 Comm: syz-executor Tainted: G OE 4.15.0-rc2+ #16
RIP: 0010:do_debug+0x222/0x250
Call Trace:
<#DB>
debug+0x3e/0x70
RIP: 0010:copy_user_enhanced_fast_string+0x10/0x20
</#DB>
_copy_from_user+0x5b/0x90
SyS_timer_create+0x33/0x80
entry_SYSCALL_64_fastpath+0x23/0x9a
The testcase sets a watchpoint (with perf_event_open) on a buffer that is
passed to timer_create() as the struct sigevent argument. In timer_create(),
copy_from_user()'s rep movsb triggers the BP. The testcase also sets
the debug registers for the guest.
However, KVM only restores host debug registers when the host has active
watchpoints, which triggers a race condition when running the testcase with
multiple threads. The guest's DR6.BS bit can escape to the host before
another thread invokes timer_create(), and do_debug() complains.
The fix is to respect do_debug()'s dr6 invariant when leaving KVM.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>