epdc: Turn on regulators unconditionally
Add hack to EPDC driver to unconditionally turn on the regulators
during initialization for Kaifa testing
epdc: Set pir display configuration
First attempt at setting our display configuration, based on info sheet from E-Ink
epdc: Add waveform for our display
epdc: Move waveform to correct folder
epdc: Update EPDC driver to use correct pixels per SDCLK and data bus width
epdc: Update panel timing information based on NXP EPD calculator values
epdc: Update waveform after attempting to fix NXP's waveform converter
epdc: Bring up our panel by default
epdc: Update panel timing values based on independent calculations
epdc: Add 4bit waveform for ES103CS1
epdc: Add support for ES103CS1 display with 4bit waveforms
epdc: Add patch from NXP to use the correct mutex when panning display
epdc: Remove all traces of the 5bit waveforms
epdc: Remove EPDC powerup hack
epdc: update parameters for 85hz
epdc: undo some custom unnecessary changes
epdc: don't do a normal grayscale update just for init
epdc: fix some printing of errors
epdc: use synchronous firmware loading so users know that the EPDC is inited and can do stuff
mxc_epdc_fb: restore powerdown delay after suspend
mxc_epdc_fb: fix inverted conditional leading to endless collisions
mxc_epdc_fb: epdc driver wants pixclock in hz, not ps
mxc_epdc_fb: add support for automatically getting updated temperature from pmic
max17135: Add some extra output for Kaifa
max17135: Make the MAX17135 driver check the PWRGOOD pin
max17135: Set the default pass number for MAX17135 to 2
max17135: specify chip version in devicetree
max17135: print ret when failing to write to device
max17135: use sysfs for programming vcom
max17135: add thermistor regulator to read temperature
max17135: get_voltage parameter
mmc
ENGR00285671 mmc: setup emmc boot partition configure methods
- Configure boot partition
Expose the interfaces that used to enable the configurations
of the boot mode of the eMMC cards.
usage how-to and examples:
Enable the boot partition 1 boot enabled.
"echo 8 > /sys/devices/soc0/soc.1/2100000.aips-bus/
219c000.usdhc/mmc_host/mmc2/mmc2\:0001/boot_config"
In order to make sure that the re-read the ext-csd of card
can be completed successfully, add the method to wait for
the finish of the busy state.
- setup boot_info message output
Output bit means of important esd_csd register
Read esd_csd info each time when cat boot_info
becasue user may change config affect esd_csd
value.
- Boot partition access howto:
About the details, please refer to the guidance of
Documentation/mmc/mmc-dev-parts.txt
To enable write access to /dev/mmcblkXbootY, disable the forced
read-only access with:
echo 0 > /sys/block/mmcblkXbootY/force_ro
To re-enable read-only access:
echo 1 > /sys/block/mmcblkXbootY/force_ro
NOTE:
- The definitions of the EXT_CSD_PART_CONFIG and EXT_CSD_BOOT_BUS_WIDTH
+------------------------------------------------------------+
| Bit7 | Bit6 | Bit5 Bit4 Bit3 | Bit2 Bit1 Bit0 |
|------|----------|-----------------------|------------------|
| X | BOOT_ACK | BOOT_PARTITION_ENABLE | PARTITION_ACCESS |
+------------------------------------------------------------+
Bit7: Reserved
Bit6: always set to vaule '1' when boot_part is enabled
Bit[5:3]:
0x0 : Device not boot enabled (default)
0x1 : Boot partition 1 enabled for boot
0x2 : Boot partition 2 enabled for boot
0x7 : User area enabled for boot
Bit[2:0]:
0x0 : No access to boot partition (default)
0x1 : R/W boot partition 1
0x2 : R/W boot partition 2
+--------------------------------------------------------------------+
| Bit7 Bit6 Bit5 | Bit4 Bit3 | Bit2 | Bit1 Bit0 |
|----------------|----------------------------------|----------------|
| X | BOOT_MODE | RESET_BOOT_BUS_WIDTH | BOOT_BUS_WIDTH |
+--------------------------------------------------------------------+
Bit [4:3] : BOOT_MODE (non-volatile)
0x0 : Use single data rate + backward compatible timings in boot
operation (default)
0x1 : Use single data rate + high speed timings in boot operation mode
0x2 : Use dual data rate in boot operation
0x3 : Reserved
Bit [2]: RESET_BOOT_BUS_WIDTH (non-volatile)
0x0 : Reset bus width to x1, single data rate and backward compatible
timings after boot operation (default)
0x1 : Retain boot bus width and boot mode after boot operation
Bit[1:0] : BOOT_BUS_WIDTH (non-volatile)
0x0 : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default)
0x1 : x4 (sdr/ddr) bus width in boot operation mode
0x2 : x8 (sdr/ddr) bus width in boot operation mode
0x3 : Reserved
- example of the boot_info:
boot_info:0x07;
ALT_BOOT_MODE:1 - Supports alternate boot method
DDR_BOOT_MODE:1 - Supports alternate dual data rate during boot
HS_BOOTMODE:1 - Supports high speed timing during boot
boot_size:2048KB
boot_partition:0x48;
BOOT_ACK:1 - Boot acknowledge sent during boot operation
BOOT_PARTITION-ENABLE: 1 - Boot partition 1 enabled
PARTITION_ACCESS:0 - No access to boot partition
boot_bus:0x00
BOOT_MODE:0 - Use single data rate + backward compatible timings
in boot operation
RESET_BOOT_BUS_WIDTH:0 - Reset bus width to x1, single data rate
and backwardcompatible timings after boot operation
BOOT_BUS_WIDTH:0 - x1 (sdr) or x4 (ddr) bus width in boot
operation mode
Signed-off-by: Richard Zhu <r65037@freescale.com>
ENGR00323682 MMC: Fixed boot_config overwritten by switch partition
In MMC driver, two variables: boot_config and part_config are used to
keep eCSD(179) PARTITION_CONFIG. The part_config is not updated when
set new boot_config, which causes the eCSD(179) is overwritten by
any following partition switching, so the new boot_config is lost.
Signed-off-by: Ye.Li <B37916@freescale.com>
(cherry picked from commit e66d21ade29855299ce048c97830a4bb79373761)
Port NXP boot_options patch to new mmc API
Set stricter permissions for boot_config
commit de5bbdd01c upstream.
pci_host_common_probe() is defined when CONFIG_PCI_HOST_COMMON=y;
therefore the function declaration should match that.
drivers/pci/host/pcie-tango.c:300:9: error:
implicit declaration of function 'pci_host_common_probe'
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 975b820b68 ]
In some cases the clock parent would be set NULL when doing re-parent,
it will cause a NULL pointer accessing if clk_set trace event is
enabled.
This patch sets the parent as "none" if the input parameter is NULL.
Fixes: dfc202ead3 (clk: Add tracepoints for hardware operations)
Signed-off-by: Cai Li <cai.li@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5c47220342 ]
Do not allow delta value to be zero since it is used as a divisor.
Fixes: 8af2a218de ("sch_red: Adaptative RED AQM")
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9fa68f6200 upstream.
Currently, almost none of the keyed hash algorithms check whether a key
has been set before proceeding. Some algorithms are okay with this and
will effectively just use a key of all 0's or some other bogus default.
However, others will severely break, as demonstrated using
"hmac(sha3-512-generic)", the unkeyed use of which causes a kernel crash
via a (potentially exploitable) stack buffer overflow.
A while ago, this problem was solved for AF_ALG by pairing each hash
transform with a 'has_key' bool. However, there are still other places
in the kernel where userspace can specify an arbitrary hash algorithm by
name, and the kernel uses it as unkeyed hash without checking whether it
is really unkeyed. Examples of this include:
- KEYCTL_DH_COMPUTE, via the KDF extension
- dm-verity
- dm-crypt, via the ESSIV support
- dm-integrity, via the "internal hash" mode with no key given
- drbd (Distributed Replicated Block Device)
This bug is especially bad for KEYCTL_DH_COMPUTE as that requires no
privileges to call.
Fix the bug for all users by adding a flag CRYPTO_TFM_NEED_KEY to the
->crt_flags of each hash transform that indicates whether the transform
still needs to be keyed or not. Then, make the hash init, import, and
digest functions return -ENOKEY if the key is still needed.
The new flag also replaces the 'has_key' bool which algif_hash was
previously using, thereby simplifying the algif_hash implementation.
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a208fa8f33 upstream.
We need to consistently enforce that keyed hashes cannot be used without
setting the key. To do this we need a reliable way to determine whether
a given hash algorithm is keyed or not. AF_ALG currently does this by
checking for the presence of a ->setkey() method. However, this is
actually slightly broken because the CRC-32 algorithms implement
->setkey() but can also be used without a key. (The CRC-32 "key" is not
actually a cryptographic key but rather represents the initial state.
If not overridden, then a default initial state is used.)
Prepare to fix this by introducing a flag CRYPTO_ALG_OPTIONAL_KEY which
indicates that the algorithm has a ->setkey() method, but it is not
required to be called. Then set it on all the CRC-32 algorithms.
The same also applies to the Adler-32 implementation in Lustre.
Also, the cryptd and mcryptd templates have to pass through the flag
from their underlying algorithm.
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f351574172 upstream.
Provide a function, kmemdup_nul(), that will create a NUL-terminated string
from an unterminated character array where the length is known in advance.
This is better than kstrndup() in situations where we already know the
string length as the strnlen() in kstrndup() is superfluous.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e6e41c311 upstream.
To avoid slab to warn about exceeded size, fail early if queue
occupies more than KMALLOC_MAX_SIZE.
Reported-by: syzbot+e4d4f9ddd4295539735d@syzkaller.appspotmail.com
Fixes: 2e0ab8ca83 ("ptr_ring: array based FIFO for pointers")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ecca8f88da upstream.
Now in sctp_setsockopt_maxseg user_frag or frag_point can be set with
val >= 8 and val <= SCTP_MAX_CHUNK_LEN. But both checks are incorrect.
val >= 8 means frag_point can even be less than SCTP_DEFAULT_MINSEGMENT.
Then in sctp_datamsg_from_user(), when it's value is greater than cookie
echo len and trying to bundle with cookie echo chunk, the first_len will
overflow.
The worse case is when it's value is equal as cookie echo len, first_len
becomes 0, it will go into a dead loop for fragment later on. In Hangbin
syzkaller testing env, oom was even triggered due to consecutive memory
allocation in that loop.
Besides, SCTP_MAX_CHUNK_LEN is the max size of the whole chunk, it should
deduct the data header for frag_point or user_frag check.
This patch does a proper check with SCTP_DEFAULT_MINSEGMENT subtracting
the sctphdr and datahdr, SCTP_MAX_CHUNK_LEN subtracting datahdr when
setting frag_point via sockopt. It also improves sctp_setsockopt_maxseg
codes.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I ran into a 4.9 build warning in randconfig testing, starting with the
KAISER patches:
arch/x86/kernel/ldt.c: In function 'alloc_ldt_struct':
arch/x86/include/asm/pgtable_types.h:208:24: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
#define __PAGE_KERNEL (__PAGE_KERNEL_EXEC | _PAGE_NX)
^
arch/x86/kernel/ldt.c:81:6: note: in expansion of macro '__PAGE_KERNEL'
__PAGE_KERNEL);
^~~~~~~~~~~~~
I originally ran into this last year when the patches were part of linux-next,
and tried to work around it by using the proper 'pteval_t' types consistently,
but that caused additional problems.
This takes a much simpler approach, and makes the argument type of the dummy
helper always 64-bit, which is wide enough for any page table layout and
won't hurt since this call is just an empty stub anyway.
Fixes: 8f0baadf2b ("kaiser: merged update")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fa80c503b upstream.
For architectures providing their own implementation of
array_index_mask_nospec() in asm/barrier.h, attempting to use WARN_ONCE() to
complain about out-of-range parameters using WARN_ON() results in a mess
of mutually-dependent include files.
Rather than unpick the dependencies, simply have the core code in nospec.h
perform the checking for us.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1517840166-15399-1-git-send-email-will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df5d45aa08 upstream.
Create a new function attribute __optimize, which allows to specify an
optimization level on a per-function basis.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f69120ce6c upstream.
Sphinx emits various (26) warnings when building make target 'htmldocs'.
Currently struct definitions contain duplicate documentation, some as
kernel-docs and some as standard c89 comments. We can reduce
duplication while cleaning up the kernel docs.
Move all kernel-docs to right above each struct member. Use the set of
all existing comments (kernel-doc and c89). Add documentation for
missing struct members and function arguments.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a16e772e66 upstream.
Since Poly1305 requires a nonce per invocation, the Linux kernel
implementations of Poly1305 don't use the crypto API's keying mechanism
and instead expect the key and nonce as the first 32 bytes of the data.
But ->setkey() is still defined as a stub returning an error code. This
prevents Poly1305 from being used through AF_ALG and will also break it
completely once we start enforcing that all crypto API users (not just
AF_ALG) call ->setkey() if present.
Fix it by removing crypto_poly1305_setkey(), leaving ->setkey as NULL.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd6ed77ad5 upstream.
Templates that use an shash spawn can use crypto_shash_alg_has_setkey()
to determine whether the underlying algorithm requires a key or not.
But there was no corresponding function for ahash spawns. Add it.
Note that the new function actually has to support both shash and ahash
algorithms, since the ahash API can be used with either.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e343e87d2 upstream.
The map_word_() functions, dating back to linux-2.6.8, try to perform
bitwise operations on a 'map_word' structure. This may have worked
with compilers that were current then (gcc-3.4 or earlier), but end
up being rather inefficient on any version I could try now (gcc-4.4 or
higher). Specifically we hit a problem analyzed in gcc PR81715 where we
fail to reuse the stack space for local variables.
This can be seen immediately in the stack consumption for
cfi_staa_erase_varsize() and other functions that (with CONFIG_KASAN)
can be up to 2200 bytes. Changing the inline functions into macros brings
this down to 1280 bytes. Without KASAN, the same problem exists, but
the stack consumption is lower to start with, my patch shrinks it from
920 to 496 bytes on with arm-linux-gnueabi-gcc-5.4, and saves around
1KB in .text size for cfi_cmdset_0020.c, as it avoids copying map_word
structures for each call to one of these helpers.
With the latest gcc-8 snapshot, the problem is fixed in upstream gcc,
but nobody uses that yet, so we should still work around it in mainline
kernels and probably backport the workaround to stable kernels as well.
We had a couple of other functions that suffered from the same gcc bug,
and all of those had a simpler workaround involving dummy variables
in the inline function. Unfortunately that did not work here, the
macro hack was the best I could come up with.
It would also be helpful to have someone to a little performance testing
on the patch, to see how much it helps in terms of CPU utilitzation.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 66f793099a)
There's no point in building init code with retpolines, since it runs before
any potentially hostile userspace does. And before the retpoline is actually
ALTERNATIVEd into place, for much of it.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: karahmed@amazon.de
Cc: peterz@infradead.org
Cc: bp@alien8.de
Link: https://lkml.kernel.org/r/1517484441-1420-2-git-send-email-dwmw@amazon.co.uk
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit f380420330)
array_index_nospec() is proposed as a generic mechanism to mitigate
against Spectre-variant-1 attacks, i.e. an attack that bypasses boundary
checks via speculative execution. The array_index_nospec()
implementation is expected to be safe for current generation CPUs across
multiple architectures (ARM, x86).
Based on an original implementation by Linus Torvalds, tweaked to remove
speculative flows by Alexei Starovoitov, and tweaked again by Linus to
introduce an x86 assembly implementation for the mask generation.
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Co-developed-by: Alexei Starovoitov <ast@kernel.org>
Suggested-by: Cyril Novikov <cnovikov@lynx.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: kernel-hardening@lists.openwall.com
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: gregkh@linuxfoundation.org
Cc: torvalds@linux-foundation.org
Cc: alan@linux.intel.com
Link: https://lkml.kernel.org/r/151727414229.33451.18411580953862676575.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit caf7501a1b)
There's a risk that a kernel which has full retpoline mitigations becomes
vulnerable when a module gets loaded that hasn't been compiled with the
right compiler or the right option.
To enable detection of that mismatch at module load time, add a module info
string "retpoline" at build time when the module was compiled with
retpoline support. This only covers compiled C source, but assembler source
or prebuilt object files are not checked.
If a retpoline enabled kernel detects a non retpoline protected module at
load time, print a warning and report it in the sysfs vulnerability file.
[ tglx: Massaged changelog ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: gregkh@linuxfoundation.org
Cc: torvalds@linux-foundation.org
Cc: jeyu@kernel.org
Cc: arjan@linux.intel.com
Link: https://lkml.kernel.org/r/20180125235028.31211-1-andi@firstfloor.org
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b027e2298b upstream.
There can be a race, if receive_buf call comes before
tty initialization completes in n_tty_open and tty->disc_data
may be NULL.
CPU0 CPU1
---- ----
000|n_tty_receive_buf_common() n_tty_open()
-001|n_tty_receive_buf2() tty_ldisc_open.isra.3()
-002|tty_ldisc_receive_buf(inline) tty_ldisc_setup()
Using ldisc semaphore lock in tty_init_dev till disc_data
initializes completely.
Signed-off-by: Gaurav Kohli <gkohli@codeaurora.org>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1410a90ae4 upstream.
HW can implement UMR wqe re-transmission in various ways.
Thus, add HCA cap to distinguish the needed fence for UMR to make
sure that the wqe wouldn't fail on mkey checks.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Acked-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Cc: Marta Rybczynska <mrybczyn@kalray.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ upstream commit be95a845cc ]
In addition to commit b2157399cc ("bpf: prevent out-of-bounds
speculation") also change the layout of struct bpf_map such that
false sharing of fast-path members like max_entries is avoided
when the maps reference counter is altered. Therefore enforce
them to be placed into separate cachelines.
pahole dump after change:
struct bpf_map {
const struct bpf_map_ops * ops; /* 0 8 */
struct bpf_map * inner_map_meta; /* 8 8 */
void * security; /* 16 8 */
enum bpf_map_type map_type; /* 24 4 */
u32 key_size; /* 28 4 */
u32 value_size; /* 32 4 */
u32 max_entries; /* 36 4 */
u32 map_flags; /* 40 4 */
u32 pages; /* 44 4 */
u32 id; /* 48 4 */
int numa_node; /* 52 4 */
bool unpriv_array; /* 56 1 */
/* XXX 7 bytes hole, try to pack */
/* --- cacheline 1 boundary (64 bytes) --- */
struct user_struct * user; /* 64 8 */
atomic_t refcnt; /* 72 4 */
atomic_t usercnt; /* 76 4 */
struct work_struct work; /* 80 32 */
char name[16]; /* 112 16 */
/* --- cacheline 2 boundary (128 bytes) --- */
/* size: 128, cachelines: 2, members: 17 */
/* sum members: 121, holes: 1, sum holes: 7 */
};
Now all entries in the first cacheline are read only throughout
the life time of the map, set up once during map creation. Overall
struct size and number of cachelines doesn't change from the
reordering. struct bpf_map is usually first member and embedded
in map structs in specific map implementations, so also avoid those
members to sit at the end where it could potentially share the
cacheline with first map values e.g. in the array since remote
CPUs could trigger map updates just as well for those (easily
dirtying members like max_entries intentionally as well) while
having subsequent values in cache.
Quoting from Google's Project Zero blog [1]:
Additionally, at least on the Intel machine on which this was
tested, bouncing modified cache lines between cores is slow,
apparently because the MESI protocol is used for cache coherence
[8]. Changing the reference counter of an eBPF array on one
physical CPU core causes the cache line containing the reference
counter to be bounced over to that CPU core, making reads of the
reference counter on all other CPU cores slow until the changed
reference counter has been written back to memory. Because the
length and the reference counter of an eBPF array are stored in
the same cache line, this also means that changing the reference
counter on one physical CPU core causes reads of the eBPF array's
length to be slow on other physical CPU cores (intentional false
sharing).
While this doesn't 'control' the out-of-bounds speculation through
masking the index as in commit b2157399cc, triggering a manipulation
of the map's reference counter is really trivial, so lets not allow
to easily affect max_entries from it.
Splitting to separate cachelines also generally makes sense from
a performance perspective anyway in that fast-path won't have a
cache miss if the map gets pinned, reused in other progs, etc out
of control path, thus also avoids unintentional false sharing.
[1] https://googleprojectzero.blogspot.ch/2018/01/reading-privileged-memory-with-side.html
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd9ff4de01 ]
Map all lookup neigh keys to INADDR_ANY for loopback/point-to-point devices
to avoid making an entry for every remote ip the device needs to talk to.
This used the be the old behavior but became broken in a263b30936
(ipv4: Make neigh lookups directly in output packet path) and later removed
in 0bb4087cbe (ipv4: Fix neigh lookup keying over loopback/point-to-point
devices) because it was broken.
Signed-off-by: Jim Westfall <jwestfall@surrealistic.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4ee806d511 ]
When a tcp socket is closed, if it detects that its net namespace is
exiting, close immediately and do not wait for FIN sequence.
For normal sockets, a reference is taken to their net namespace, so it will
never exit while the socket is open. However, kernel sockets do not take a
reference to their net namespace, so it may begin exiting while the kernel
socket is still open. In this case if the kernel socket is a tcp socket,
it will stay open trying to complete its close sequence. The sock's dst(s)
hold a reference to their interface, which are all transferred to the
namespace's loopback interface when the real interfaces are taken down.
When the namespace tries to take down its loopback interface, it hangs
waiting for all references to the loopback interface to release, which
results in messages like:
unregister_netdevice: waiting for lo to become free. Usage count = 1
These messages continue until the socket finally times out and closes.
Since the net namespace cleanup holds the net_mutex while calling its
registered pernet callbacks, any new net namespace initialization is
blocked until the current net namespace finishes exiting.
After this change, the tcp socket notices the exiting net namespace, and
closes immediately, releasing its dst(s) and their reference to the
loopback interface, which lets the net namespace continue exiting.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1711407
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=97811
Signed-off-by: Dan Streetman <ddstreet@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e9191ffb65 ]
Commit 513674b5a2 ("net: reevalulate autoflowlabel setting after
sysctl setting") removed the initialisation of
ipv6_pinfo::autoflowlabel and added a second flag to indicate
whether this field or the net namespace default should be used.
The getsockopt() handling for this case was not updated, so it
currently returns 0 for all sockets for which IPV6_AUTOFLOWLABEL is
not explicitly enabled. Fix it to return the effective value, whether
that has been set at the socket or net namespace level.
Fixes: 513674b5a2 ("net: reevalulate autoflowlabel setting after sysctl ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e04072685 upstream.
[resend due to me forgetting to cc: linux-api the first time around I
posted these back on Feb 23]
From: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason these values are not in the uapi header file, so any
libc has to define it themselves. To prevent them from needing to do
this, just have the kernel provide the correct values.
Reported-by: Elliott Hughes <enh@google.com>
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c73322d098 upstream.
Patch series "mm: kswapd spinning on unreclaimable nodes - fixes and
cleanups".
Jia reported a scenario in which the kswapd of a node indefinitely spins
at 100% CPU usage. We have seen similar cases at Facebook.
The kernel's current method of judging its ability to reclaim a node (or
whether to back off and sleep) is based on the amount of scanned pages
in proportion to the amount of reclaimable pages. In Jia's and our
scenarios, there are no reclaimable pages in the node, however, and the
condition for backing off is never met. Kswapd busyloops in an attempt
to restore the watermarks while having nothing to work with.
This series reworks the definition of an unreclaimable node based not on
scanning but on whether kswapd is able to actually reclaim pages in
MAX_RECLAIM_RETRIES (16) consecutive runs. This is the same criteria
the page allocator uses for giving up on direct reclaim and invoking the
OOM killer. If it cannot free any pages, kswapd will go to sleep and
leave further attempts to direct reclaim invocations, which will either
make progress and re-enable kswapd, or invoke the OOM killer.
Patch #1 fixes the immediate problem Jia reported, the remainder are
smaller fixlets, cleanups, and overall phasing out of the old method.
Patch #6 is the odd one out. It's a nice cleanup to get_scan_count(),
and directly related to #5, but in itself not relevant to the series.
If the whole series is too ambitious for 4.11, I would consider the
first three patches fixes, the rest cleanups.
This patch (of 9):
Jia He reports a problem with kswapd spinning at 100% CPU when
requesting more hugepages than memory available in the system:
$ echo 4000 >/proc/sys/vm/nr_hugepages
top - 13:42:59 up 3:37, 1 user, load average: 1.09, 1.03, 1.01
Tasks: 1 total, 1 running, 0 sleeping, 0 stopped, 0 zombie
%Cpu(s): 0.0 us, 12.5 sy, 0.0 ni, 85.5 id, 2.0 wa, 0.0 hi, 0.0 si, 0.0 st
KiB Mem: 31371520 total, 30915136 used, 456384 free, 320 buffers
KiB Swap: 6284224 total, 115712 used, 6168512 free. 48192 cached Mem
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
76 root 20 0 0 0 0 R 100.0 0.000 217:17.29 kswapd3
At that time, there are no reclaimable pages left in the node, but as
kswapd fails to restore the high watermarks it refuses to go to sleep.
Kswapd needs to back away from nodes that fail to balance. Up until
commit 1d82de618d ("mm, vmscan: make kswapd reclaim in terms of
nodes") kswapd had such a mechanism. It considered zones whose
theoretically reclaimable pages it had reclaimed six times over as
unreclaimable and backed away from them. This guard was erroneously
removed as the patch changed the definition of a balanced node.
However, simply restoring this code wouldn't help in the case reported
here: there *are* no reclaimable pages that could be scanned until the
threshold is met. Kswapd would stay awake anyway.
Introduce a new and much simpler way of backing off. If kswapd runs
through MAX_RECLAIM_RETRIES (16) cycles without reclaiming a single
page, make it back off from the node. This is the same number of shots
direct reclaim takes before declaring OOM. Kswapd will go to sleep on
that node until a direct reclaimer manages to reclaim some pages, thus
proving the node reclaimable again.
[hannes@cmpxchg.org: check kswapd failure against the cumulative nr_reclaimed count]
Link: http://lkml.kernel.org/r/20170306162410.GB2090@cmpxchg.org
[shakeelb@google.com: fix condition for throttle_direct_reclaim]
Link: http://lkml.kernel.org/r/20170314183228.20152-1-shakeelb@google.com
Link: http://lkml.kernel.org/r/20170228214007.5621-2-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Reported-by: Jia He <hejianet@gmail.com>
Tested-by: Jia He <hejianet@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5132ede0fe upstream.
This reverts commit 6cfb521ac0.
Turns out distros do not want to make retpoline as part of their "ABI",
so this patch should not have been merged. Sorry Andi, this was my
fault, I suggested it when your original patch was the "correct" way of
doing this instead.
Reported-by: Jiri Kosina <jikos@kernel.org>
Fixes: 6cfb521ac0 ("module: Add retpoline tag to VERMAGIC")
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: rusty@rustcorp.com.au
Cc: arjan.van.de.ven@intel.com
Cc: jeyu@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fac5148257 upstream.
With CONFIG_OF enabled on x86, we get the following error on boot:
"
Failed to find cpu0 device node
Unable to detect cache hierarchy from DT for CPU 0
"
and the cacheinfo fails to get populated in the corresponding sysfs
entries. This is because cache_setup_of_node looks for of_node for
setting up the shared cpu_map without checking that it's already
populated in the architecture specific callback.
In order to indicate that the shared cpu_map is already populated, this
patch introduces a boolean `cpu_map_populated` in struct cpu_cacheinfo
that can be used by the generic code to skip cache_shared_cpu_map_setup.
This patch also sets that boolean for x86.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cfb521ac0 upstream.
Add a marker for retpoline to the module VERMAGIC. This catches the case
when a non RETPOLINE compiled module gets loaded into a retpoline kernel,
making it insecure.
It doesn't handle the case when retpoline has been runtime disabled. Even
in this case the match of the retcompile status will be enforced. This
implies that even with retpoline run time disabled all modules loaded need
to be recompiled.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: David Woodhouse <dwmw@amazon.co.uk>
Cc: rusty@rustcorp.com.au
Cc: arjan.van.de.ven@intel.com
Cc: jeyu@kernel.org
Cc: torvalds@linux-foundation.org
Link: https://lkml.kernel.org/r/20180116205228.4890-1-andi@firstfloor.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 745dfa0d8e upstream.
The ioctl SET_FORCE_LOW_DMA has never worked since the initial git
check-in, and the respective setting is nowadays handled correctly. So
disable it entirely.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e390f9a968 upstream.
The '__unreachable' and '__func_stack_frame_non_standard' sections are
only used at compile time. They're discarded for vmlinux but they
should also be discarded for modules.
Since this is a recurring pattern, prefix the section names with
".discard.". It's a nice convention and vmlinux.lds.h already discards
such sections.
Also remove the 'a' (allocatable) flag from the __unreachable section
since it doesn't make sense for a discarded section.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Jessica Yu <jeyu@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: d1091c7fa3 ("objtool: Improve detection of BUG() and other dead ends")
Link: http://lkml.kernel.org/r/20170301180444.lhd53c5tibc4ns77@treble
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[dwmw2: Remove the unreachable part in backporting since it's not here yet]
Signed-off-by: David Woodhouse <dwmw@amazon.co.ku>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87590ce6e3 upstream.
As the meltdown/spectre problem affects several CPU architectures, it makes
sense to have common way to express whether a system is affected by a
particular vulnerability or not. If affected the way to express the
mitigation should be common as well.
Create /sys/devices/system/cpu/vulnerabilities folder and files for
meltdown, spectre_v1 and spectre_v2.
Allow architectures to override the show function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lkml.kernel.org/r/20180107214913.096657732@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2157399cc upstream.
Under speculation, CPUs may mis-predict branches in bounds checks. Thus,
memory accesses under a bounds check may be speculated even if the
bounds check fails, providing a primitive for building a side channel.
To avoid leaking kernel data round up array-based maps and mask the index
after bounds check, so speculated load with out of bounds index will load
either valid value from the array or zero from the padded area.
Unconditionally mask index for all array types even when max_entries
are not rounded to power of 2 for root user.
When map is created by unpriv user generate a sequence of bpf insns
that includes AND operation to make sure that JITed code includes
the same 'index & index_mask' operation.
If prog_array map is created by unpriv user replace
bpf_tail_call(ctx, map, index);
with
if (index >= max_entries) {
index &= map->index_mask;
bpf_tail_call(ctx, map, index);
}
(along with roundup to power 2) to prevent out-of-bounds speculation.
There is secondary redundant 'if (index >= max_entries)' in the interpreter
and in all JITs, but they can be optimized later if necessary.
Other array-like maps (cpumap, devmap, sockmap, perf_event_array, cgroup_array)
cannot be used by unpriv, so no changes there.
That fixes bpf side of "Variant 1: bounds check bypass (CVE-2017-5753)" on
all architectures with and without JIT.
v2->v3:
Daniel noticed that attack potentially can be crafted via syscall commands
without loading the program, so add masking to those paths as well.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Slaby <jslaby@suse.cz>
[ Backported to 4.9 - gregkh ]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c21a48055 upstream.
This patch fixes bug where early se_cmd exceptions that occur
before backend execution can result in use-after-free if/when
a subsequent ABORT_TASK occurs for the same tag.
Since an early se_cmd exception will have had se_cmd added to
se_session->sess_cmd_list via target_get_sess_cmd(), it will
not have CMD_T_COMPLETE set by the usual target_complete_cmd()
backend completion path.
This causes a subsequent ABORT_TASK + __target_check_io_state()
to signal ABORT_TASK should proceed. As core_tmr_abort_task()
executes, it will bring the outstanding se_cmd->cmd_kref count
down to zero releasing se_cmd, after se_cmd has already been
queued with error status into fabric driver response path code.
To address this bug, introduce a CMD_T_PRE_EXECUTE bit that is
set at target_get_sess_cmd() time, and cleared immediately before
backend driver dispatch in target_execute_cmd() once CMD_T_ACTIVE
is set.
Then, check CMD_T_PRE_EXECUTE within __target_check_io_state() to
determine when an early exception has occured, and avoid aborting
this se_cmd since it will have already been queued into fabric
driver response path code.
Reported-by: Donald White <dew@datera.io>
Cc: Donald White <dew@datera.io>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 879626e3a5 ]
Note in the databook - Section 4.4 - EEE :
" The EEE feature is not supported when the MAC is configured to use the
TBI, RTBI, SMII, RMII or SGMII single PHY interface. Even if the MAC
supports multiple PHY interfaces, you should activate the EEE mode only
when the MAC is operating with GMII, MII, or RGMII interface."
Applying this restriction solves a stability issue observed on Amlogic
gxl platforms operating with RMII interface and the internal PHY.
Fixes: 83bf79b6bb ("stmmac: disable at run-time the EEE if not supported")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5133550296 ]
Renesas SH7757 has 2 Fast and 2 Gigabit Ether controllers, while the
'sh_eth' driver can only reset and initialize TSU of the first controller
pair. Shimoda-san tried to solve that adding the 'needs_init' member to the
'struct sh_eth_plat_data', however the platform code still never sets this
flag. I think that we can infer this information from the 'devno' variable
(set to 'platform_device::id') and reset/init the Ether controller pair
only for an even 'devno'; therefore 'sh_eth_plat_data::needs_init' can be
removed...
Fixes: 150647fb2c ("net: sh_eth: change the condition of initialization")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e39d200fa5 upstream.
Reported by syzkaller:
BUG: KASAN: stack-out-of-bounds in write_mmio+0x11e/0x270 [kvm]
Read of size 8 at addr ffff8803259df7f8 by task syz-executor/32298
CPU: 6 PID: 32298 Comm: syz-executor Tainted: G OE 4.15.0-rc2+ #18
Hardware name: LENOVO ThinkCentre M8500t-N000/SHARKBAY, BIOS FBKTC1AUS 02/16/2016
Call Trace:
dump_stack+0xab/0xe1
print_address_description+0x6b/0x290
kasan_report+0x28a/0x370
write_mmio+0x11e/0x270 [kvm]
emulator_read_write_onepage+0x311/0x600 [kvm]
emulator_read_write+0xef/0x240 [kvm]
emulator_fix_hypercall+0x105/0x150 [kvm]
em_hypercall+0x2b/0x80 [kvm]
x86_emulate_insn+0x2b1/0x1640 [kvm]
x86_emulate_instruction+0x39a/0xb90 [kvm]
handle_exception+0x1b4/0x4d0 [kvm_intel]
vcpu_enter_guest+0x15a0/0x2640 [kvm]
kvm_arch_vcpu_ioctl_run+0x549/0x7d0 [kvm]
kvm_vcpu_ioctl+0x479/0x880 [kvm]
do_vfs_ioctl+0x142/0x9a0
SyS_ioctl+0x74/0x80
entry_SYSCALL_64_fastpath+0x23/0x9a
The path of patched vmmcall will patch 3 bytes opcode 0F 01 C1(vmcall)
to the guest memory, however, write_mmio tracepoint always prints 8 bytes
through *(u64 *)val since kvm splits the mmio access into 8 bytes. This
leaks 5 bytes from the kernel stack (CVE-2017-17741). This patch fixes
it by just accessing the bytes which we operate on.
Before patch:
syz-executor-5567 [007] .... 51370.561696: kvm_mmio: mmio write len 3 gpa 0x10 val 0x1ffff10077c1010f
After patch:
syz-executor-13416 [002] .... 51302.299573: kvm_mmio: mmio write len 3 gpa 0x10 val 0xc1010f
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cef0acd4d7 upstream.
Add a flag that indicates that the WEP ICV was stripped from an
RX packet, allowing the device to not transfer that if it's
already checked.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdcf0a423e upstream.
In testing, we found that nfsd threads may call set_groups in parallel
for the same entry cached in auth.unix.gid, racing in the call of
groups_sort, corrupting the groups for that entry and leading to
permission denials for the client.
This patch:
- Make groups_sort globally visible.
- Move the call to groups_sort to the modifiers of group_info
- Remove the call to groups_sort from set_groups
Link: http://lkml.kernel.org/r/20171211151420.18655-1-thiago.becker@gmail.com
Signed-off-by: Thiago Rafael Becker <thiago.becker@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: NeilBrown <neilb@suse.com>
Acked-by: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>