This is a combination of commits 919d46e37e04 (ENGR00265935 net: fec:
add pm_qos to avoid cpu enter to wait mode) and 8a12c90c9974
(ENGR00313685-14 net: fec: check workaround for FEC_QUIRK_BUG_WAITMODE)
from imx_3.10.y branch. It's added for imx_3.14.y branch to work around
imx6qdl issue ERR006687 (ENET: Only the ENET wake-up interrupt request
can wake the system from Wait mode).
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
(cherry-pick and merge from commit: 4f406fae257cc7945a0e3a425213440bb12ba345)
[ Upstream commit 8ac1ee6f4d ]
Clang warns that the address of a pointer will always evaluated as true
in a boolean context:
drivers/net/ethernet/mellanox/mlx4/eq.c:243:11: warning: address of
array 'eq->affinity_mask' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!eq->affinity_mask || cpumask_empty(eq->affinity_mask))
~~~~~^~~~~~~~~~~~~
1 warning generated.
Use cpumask_available, introduced in commit f7e30f01a9 ("cpumask: Add
helper cpumask_available()"), which does the proper checking and avoids
this warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/86
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2fe397a395 ]
EtherAVB hardware requires 0 to be written to status register bits in
order to clear them, however, care must be taken not to:
1. Clear other bits, by writing zero to them
2. Write one to reserved bits
This patch corrects the ravb driver with respect to the second point above.
This is done by defining reserved bit masks for the affected registers and,
after auditing the code, ensure all sites that may write a one to a
reserved bit use are suitably masked.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 08e39982ef ]
On the Netgear WNDAP620, the emac ethernet isn't receiving nor
xmitting any frames from/to the RTL8363SB (identifies itself
as a RTL8367RB).
This is caused by the emac hardware not knowing the forced link
parameters for speed, duplex, pause, etc.
This begs the question, how this was working on the original
driver code, when it was necessary to set the phy_address and
phy_map to 0xffffffff. But I guess without access to the old
PPC405/440/460 hardware, it's not possible to know.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eb4ed8e2d7 ]
Create a new configuration for the sama5d3-macb new compatibility string.
This configuration disables scatter-gather because we experienced lock down
of the macb interface of this particular SoC under very high load.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit edf2ef7242 ]
Synopsys DWC Ethernet MAC can be configured to have 1..32, 64, or
128 unicast filter entries. (Table 7-8 MAC Address Registers from
databook) Fix dwmac1000_validate_ucast_entries() to accept values
between 1 and 32 in addition.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ff58e2df62 ]
When FW floods the driver with control messages try to exit the cmsg
processing loop every now and then to avoid soft lockups. Cmsg
processing is generally very lightweight so 512 seems like a reasonable
budget, which should not be exceeded under normal conditions.
Fixes: 77ece8d5f1 ("nfp: add control vNIC datapath")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0f3b914c9c ]
RX queue config for bonding master could be different from its slave
device(s). With the commit 6a9e461f6f ("bonding: pass link-local
packets to bonding master also."), the packet is reinjected into stack
with skb->dev as bonding master. This potentially triggers the
message:
"bondX received packet on queue Y, but number of RX queues is Z"
whenever the queue that packet is received on is higher than the
numrxqueues on bonding master (Y > Z).
Fixes: 6a9e461f6f ("bonding: pass link-local packets to bonding master also.")
Reported-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6a9e461f6f ]
Commit b89f04c61e ("bonding: deliver link-local packets with
skb->dev set to link that packets arrived on") changed the behavior
of how link-local-multicast packets are processed. The change in
the behavior broke some legacy use cases where these packets are
expected to arrive on bonding master device also.
This patch passes the packet to the stack with the link it arrived
on as well as passes to the bonding-master device to preserve the
legacy use case.
Fixes: b89f04c61e ("bonding: deliver link-local packets with skb->dev set to link that packets arrived on")
Reported-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 11aa5800ed ]
The code that deals with eswitch vport bw guarantee was going beyond the
eswitch vport array limit, fix that. This was pointed out by the kernel
address sanitizer (KASAN).
The error from KASAN log:
[2018-09-15 15:04:45] BUG: KASAN: slab-out-of-bounds in
mlx5_eswitch_set_vport_rate+0x8c1/0xae0 [mlx5_core]
Fixes: c9497c9890 ("net/mlx5: Add support for setting VF min rate")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d26ed6b0e5 ]
This patch fixes skb_shared area, which will be corrupted
upon reception of 4K jumbo packets.
Originally build_skb usage purpose was to reuse page for skb to eliminate
needs of extra fragments. But that logic does not take into account that
skb_shared_info should be reserved at the end of skb data area.
In case packet data consumes all the page (4K), skb_shinfo location
overflows the page. As a consequence, __build_skb zeroed shinfo data above
the allocated page, corrupting next page.
The issue is rarely seen in real life because jumbo are normally larger
than 4K and that causes another code path to trigger.
But it 100% reproducible with simple scapy packet, like:
sendp(IP(dst="192.168.100.3") / TCP(dport=443) \
/ Raw(RandString(size=(4096-40))), iface="enp1s0")
Fixes: 018423e90b ("net: ethernet: aquantia: Add ring support code")
Reported-by: Friedemann Gerold <f.gerold@b-c-s.de>
Reported-by: Michael Rauch <michael@rauch.be>
Signed-off-by: Friedemann Gerold <f.gerold@b-c-s.de>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cee2648762 ]
In flow steering, if asked to, the hardware matches on the first ethertype
which is not vlan. It's possible to set a rule as follows, which is meant
to match on untagged packet, but will match on a vlan packet:
tc filter add dev eth0 parent ffff: protocol ip flower ...
To avoid this for packets with single tag, we set vlan masks to tell
hardware to check the tags for every matched packet.
Fixes: 095b6cfd69 ('net/mlx5e: Add TC vlan match parsing')
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bf3b452b7a ]
The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.
Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.
Fixes: d9338023fb ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0431100b3d ]
Currently we are always setting the tail address of descriptor list to
the end of the pre-allocated list.
According to databook this is not correct. Tail address should point to
the last available descriptor + 1, which means we have to update the
tail address everytime we call the xmit function.
This should make no impact in older versions of MAC but in newer
versions there are some DMA features which allows the IP to fetch
descriptors in advance and in a non sequential order so its critical
that we set the tail address correctly.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: f748be531d ("stmmac: support new GMAC4")
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f7617705b ]
Added support for Gemalto's Cinterion ALASxx WWAN interfaces
by adding QMI_FIXED_INTF with Cinterion's VID and PID.
Signed-off-by: Giacinto Cifelli <gciofono@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c333fa0c4f ]
In regular NIC transmission flow, driver always configures MAC using
Tx queue zero descriptor as a part of MAC learning flow.
But with multi Tx queue supported NIC, regular transmission can occur on
any non-zero Tx queue and from that context it uses
Tx queue zero descriptor to configure MAC, at the same time TX queue
zero could be used by another CPU for regular transmission
which could lead to Tx queue zero descriptor corruption and cause FW
abort.
This patch fixes this in such a way that driver always configures
learned MAC address from the same Tx queue which is used for
regular transmission.
Fixes: 7e2cf4feba ("qlcnic: change driver hardware interface mechanism")
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 45ec318578 ]
The AON_PM_L2 is normally used to trigger and identify the source of a
wake-up event. Since the RX_SYS clock is no longer turned off, we also
have an interrupt being sent to the SYSTEMPORT INTRL_2_0 controller, and
that interrupt remains active up until the magic packet detector is
disabled which happens much later during the driver resumption.
The race happens if we have a CPU that is entering the SYSTEMPORT
INTRL2_0 handler during resume, and another CPU has managed to clear the
wake-up interrupt during bcm_sysport_resume_from_wol(). In that case, we
have the first CPU stuck in the interrupt handler with an interrupt
cause that has been cleared under its feet, and so we keep returning
IRQ_NONE and we never make any progress.
This was not a problem before because we would always turn off the
RX_SYS clock during WoL, so the SYSTEMPORT INTRL2_0 would also be turned
off as well, thus not latching the interrupt.
The fix is to make sure we do not enable either the MPD or
BRCM_TAG_MATCH interrupts since those are redundant with what the
AON_PM_L2 interrupt controller already processes and they would cause
such a race to occur.
Fixes: bb9051a2b2 ("net: systemport: Add support for WAKE_FILTER")
Fixes: 83e82f4c70 ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 774268f3e5 ]
When no Tx IRQ is available, the txq_done() routine (called from
tx_done()) shouldn't be called from the polling function, as in such
case it is already called in the Tx path thanks to an hrtimer. This
mostly occurred when using PPv2.1, as the engine then do not have Tx
IRQs.
Fixes: edc660fa09 ("net: mvpp2: replace TX coalescing interrupts with hrtimer")
Reported-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 35f3625c21 ]
When offloading the L3 and L4 csum computation on TX, we need to extract
the l3_proto from the ethtype, independently of the presence of a vlan
tag.
The actual driver uses skb->protocol as-is, resulting in packets with
the wrong L4 checksum being sent when there's a vlan tag in the packet
header and checksum offloading is enabled.
This commit makes use of vlan_protocol_get() to get the correct ethtype
regardless the presence of a vlan tag.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e9361efa7 ]
If SMMU is on, there is more likely that skb_shinfo(skb)->frags[i]
can not send by a single BD. when this happen, the
hns_nic_net_xmit_hw function map the whole data in a frags using
skb_frag_dma_map, but unmap each BD' data individually when tx is
done, which causes problem when SMMU is on.
This patch fixes this problem by ummapping the whole data in a
frags when tx is done.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 54baca0963 ]
There is no reason to open code what the switch setup function does, in
fact, because we just issued a switch reset, we would make all the
register get their default values, including for instance, having unused
port be enabled again and wasting power and leading to an inappropriate
switch core clock being selected.
Fixes: 8cfa94984c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a2bf74f4e1 ]
When the driver probe fails, all the resources that were allocated prior
to the failure must be freed. However, hwrm dma response memory is not
getting freed.
This patch fixes the problem described above.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 73f21c653f ]
The current netpoll implementation in the bnxt_en driver has problems
that may miss TX completion events. bnxt_poll_work() in effect is
only handling at most 1 TX packet before exiting. In addition,
there may be in flight TX completions that ->poll() may miss even
after we fix bnxt_poll_work() to handle all visible TX completions.
netpoll may not call ->poll() again and HW may not generate IRQ
because the driver does not ARM the IRQ when the budget (0 for netpoll)
is reached.
We fix it by handling all TX completions and to always ARM the IRQ
when we exit ->poll() with 0 budget.
Also, the logic to ACK the completion ring in case it is almost filled
with TX completions need to be adjusted to take care of the 0 budget
case, as discussed with Eric Dumazet <edumazet@google.com>
Reported-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Song Liu <songliubraving@fb.com>
Tested-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ef0f58ed7 upstream.
The skb may be freed in tx completion context before
trace_ath10k_wmi_cmd is called. This can be easily captured when
KASAN(Kernel Address Sanitizer) is enabled. The fix is to move
trace_ath10k_wmi_cmd before the send operation. As the ret has no
meaning in trace_ath10k_wmi_cmd then, so remove this parameter too.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 780e83c259 upstream.
Both len and off are frontend specified values, so we need to make
sure there's no overflow when adding the two for the bounds check. We
also want to avoid undefined behavior and hence use off to index into
->hash.mapping[] only after bounds checking. This at the same time
allows to take care of not applying off twice for the bounds checking
against vif->num_queues.
It is also insufficient to bounds check copy_op.len, as this is len
truncated to 16 bits.
This is XSA-270 / CVE-2018-15471.
Reported-by: Felix Wilhelm <fwilhelm@google.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Tested-by: Paul Durrant <paul.durrant@citrix.com>
Cc: stable@vger.kernel.org [4.7 onwards]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4233cfe6ec upstream.
The NIC driver should only enable interrupts when napi_complete_done()
returns true. This patch adds the check for ixgbe.
Cc: stable@vger.kernel.org # 4.10+
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ad5690199 ]
After system suspend, sometimes the r8169 doesn't work when ethernet
cable gets pluggued.
This issue happens because rtl_reset_work() doesn't get called from
rtl8169_runtime_resume(), after system suspend.
In rtl_task(), RTL_FLAG_TASK_* only gets cleared if this condition is
met:
if (!netif_running(dev) ||
!test_bit(RTL_FLAG_TASK_ENABLED, tp->wk.flags))
...
If RTL_FLAG_TASK_ENABLED was cleared during system suspend while
RTL_FLAG_TASK_RESET_PENDING was set, the next rtl_schedule_task() won't
schedule task as the flag is still there.
So in addition to clearing RTL_FLAG_TASK_ENABLED, also clears other
flags.
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 28abf4e9c9 ]
Add READ_ONCE calls where necessary (for example when iterating
over a memory field that gets updated by the hardware).
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ef5b0771d2 ]
The buffer length field in the ena rx descriptor is 16 bit, and the
current driver passes a full page in each ena rx descriptor.
When PAGE_SIZE equals 64kB or more, the buffer length field becomes
zero.
To solve this issue, limit the ena Rx descriptor to use 16kB even
when allocating 64kB kernel pages. This change would not impact ena
device functionality, as 16kB is still larger than maximum MTU.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 16fe10cf92 ]
The kernel module may sleep with holding a spinlock.
The function call paths (from bottom to top) in Linux-4.16 are:
[FUNC] usleep_range
drivers/net/ethernet/cadence/macb_main.c, 648:
usleep_range in macb_halt_tx
drivers/net/ethernet/cadence/macb_main.c, 730:
macb_halt_tx in macb_tx_error_task
drivers/net/ethernet/cadence/macb_main.c, 721:
_raw_spin_lock_irqsave in macb_tx_error_task
To fix this bug, usleep_range() is replaced with udelay().
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 455c4401fe ]
If there are packets in hardware when changing the speed
or duplex, it may cause hardware hang up.
This patch adds netif_carrier_off before change speed and
duplex in ethtool_ops.set_link_ksettings, and adds
netif_carrier_on after complete the change.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 31fabbee8f ]
If there are packets in hardware when changing the speed
or duplex, it may cause hardware hang up.
This patch adds the code for waiting chip to clean the all
pkts(TX & RX) in chip when the driver uses the function named
"adjust link".
This patch cleans the pkts as follows:
1) close rx of chip, close tx of protocol stack.
2) wait rcb, ppe, mac to clean.
3) adjust link
4) open rx of chip, open tx of protocol stack.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d7c863a2f6 ]
The mac80211_hwsim driver intends to say that it supports up to four
STBC receive streams, but instead it ends up saying something undefined.
The IEEE80211_VHT_CAP_RXSTBC_X macros aren't independent bits that can
be ORed together, but values. In this case, _4 is the appropriate one
to use.
Signed-off-by: Danek Duvall <duvall@comfychair.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 484004339d ]
Syzbot continues to try to create mac80211_hwsim radios, and
manages to pass parameters that are later checked with WARN_ON
in cfg80211 - catch another one in hwsim directly.
Reported-by: syzbot+2a12f11c306afe871c1f@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee400a3f1b ]
In 'e1000_set_ringparam()', the tx_ring and rx_ring are updated with new value
and the old tx/rx rings are freed only when the device is up. There are resource
leaks on old tx/rx rings when the device is not up. This bug is reported by COD,
a tool for testing kernel module binaries I am building.
This patch fixes the bug by always calling 'kfree()' on old tx/rx rings in
'e1000_set_ringparam()'.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cf1acec008 ]
When the device is not up, the call to 'e1000_up()' from the error handling path
of 'e1000_set_ringparam()' causes a kernel oops with a null-pointer
dereference. The null-pointer dereference is triggered in function
'e1000_alloc_rx_buffers()' at line 'buffer_info = &rx_ring->buffer_info[i]'.
This bug was reported by COD, a tool for testing kernel module binaries I am
building. This bug was also detected by KFI from Dr. Kai Cong.
This patch fixes the bug by checking on 'netif_running()' before calling
'e1000_up()' in 'e1000_set_ringparam()'.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b1ccd4c0ab ]
skb->truesize is not meant to be tracking amount of used bytes in a skb,
but amount of reserved/consumed bytes in memory.
For instance, if we use a single byte in last page fragment, we have to
account the full size of the fragment.
So skb_add_rx_frag needs to calculate the length of the entire buffer into
turesize.
Fixes: 9cbe9fd521 ("net: hns: optimize XGE capability by reducing cpu usage")
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3ed614dce3 ]
When enable the config item "CONFIG_ARM64_64K_PAGES", the size of PAGE_SIZE
is 65536(64K). But the type of length and page_offset are u16, they will
overflow. So change them to u32.
Fixes: 6fe6611ff2 ("net: add Hisilicon Network Subsystem hnae framework support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b310974e04 ]
Keep sending mailbox commands to the MFW when it is not responsive ends up
with a redundant amount of timeout expiries.
This patch prints the MCP status on the first command which is not
responded, and blocks the following commands.
Since the (un)load request commands might be not responded due to other
PFs, the patch also adds the option to skip the blocking upon a failure.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eaa50fc59e ]
The MFW manages an internal lock to prevent concurrent hardware
(de)initialization of different PFs.
This, together with the busy-waiting for the MFW's responses for commands,
might lead to a deadlock during concurrent load or unload of PFs.
This patch adds the option to sleep within the busy-waiting, and uses it
for the (un)load requests (which are not sent from an interrupt context) to
prevent the possible deadlock.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 76271809f4 ]
Successive iterations of halting and resuming the management chip (MCP)
might fail, since currently the driver doesn't wait for these operations to
actually take place.
This patch prevents the driver from moving forward before the operations
are reflected in the state register.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f00d25f315 ]
The MFW might be reset and re-update its shared memory.
Upon the detection of such a reset the driver rereads this memory, but it
has to wait till the data is valid.
This patch adds the missing wait for a data ready indication.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4ec7cece87 ]
Otherwise we can get:
WARNING: CPU: 0 PID: 55 at drivers/net/wireless/ti/wlcore/io.h:84
I've only seen this few times with the runtime PM patches enabled
so this one is probably not needed before that. This seems to
work currently based on the current PM implementation timer. Let's
apply this separately though in case others are hitting this issue.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c9a61469fc ]
The last value in the log_table wraps around to a negative value
since s16 has a value range of -32768 to 32767. This is not what
the table intends to represent. Use the closest positive value
32767.
This fixes a warning seen with clang:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_qmath.c:216:2: warning:
implicit conversion from 'int' to 's16' (aka 'short') changes
value from 32768
to -32768 [-Wconstant-conversion]
32768
^~~~~
1 warning generated.
Fixes: 4c0bfeaae9 ("brcmsmac: fix array out-of-bounds access in qm_log10")
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ae636fb155 ]
This is a static checker fix, not something I have tested. The issue
is that on the second iteration through the loop, we jump forward by
le32_to_cpu(auth_req->length) bytes. The problem is that if the length
is more than "buflen" then we end up with a negative "buflen". A
negative buflen is type promoted to a high positive value and the loop
continues but it's accessing beyond the end of the buffer.
I believe the "auth_req->length" comes from the firmware and if the
firmware is malicious or buggy, you're already toasted so the impact of
this bug is probably not very severe.
Fixes: 030645aceb ("rndis_wlan: handle 802.11 indications from device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f04950f32 ]
When running iperf on ath10k SDIO, TX can stop working:
iperf -c 192.168.1.1 -i 1 -t 20 -w 10K
[ 3] 0.0- 1.0 sec 2.00 MBytes 16.8 Mbits/sec
[ 3] 1.0- 2.0 sec 3.12 MBytes 26.2 Mbits/sec
[ 3] 2.0- 3.0 sec 3.25 MBytes 27.3 Mbits/sec
[ 3] 3.0- 4.0 sec 655 KBytes 5.36 Mbits/sec
[ 3] 4.0- 5.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 5.0- 6.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 6.0- 7.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 7.0- 8.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 8.0- 9.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 9.0-10.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 0.0-10.3 sec 9.01 MBytes 7.32 Mbits/sec
There are frames in the ieee80211_txq and there are frames that have
been removed from from this queue, but haven't yet been sent on the wire
(num_pending_tx).
When num_pending_tx reaches max_num_pending_tx, we will stop the queues
by calling ieee80211_stop_queues().
As frames that have previously been sent for transmission
(num_pending_tx) are completed, we will decrease num_pending_tx and wake
the queues by calling ieee80211_wake_queue(). ieee80211_wake_queue()
does not call wake_tx_queue, so we might still have frames in the
queue at this point.
While the queues were stopped, the socket buffer might have filled up,
and in order for user space to write more, we need to free the frames
in the queue, since they are accounted to the socket. In order to free
them, we first need to transmit them.
This problem cannot be reproduced on low-latency devices, e.g. pci,
since they call ath10k_mac_tx_push_pending() from
ath10k_htt_txrx_compl_task(). ath10k_htt_txrx_compl_task() is not called
on high-latency devices.
Fix the problem by calling ath10k_mac_tx_push_pending(), after
processing rx packets, just like for low-latency devices, also in the
SDIO case. Since we are calling ath10k_mac_tx_push_pending() directly,
we also need to export it.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ab4e6ee578 ]
Since a phy_device is added to the global mdio_bus list during
phy_device_register(), but a phy_device's phy_driver doesn't get
attached until phy_probe(). It's possible of_phy_find_device() in
xgmiitorgmii will return a valid phy with a NULL phy_driver. Leading to
a NULL pointer access during the memcpy().
Fixes this Oops:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.40 #1
Hardware name: Xilinx Zynq Platform
task: ce4c8d00 task.stack: ce4ca000
PC is at memcpy+0x48/0x330
LR is at xgmiitorgmii_probe+0x90/0xe8
pc : [<c074bc68>] lr : [<c0529548>] psr: 20000013
sp : ce4cbb54 ip : 00000000 fp : ce4cbb8c
r10: 00000000 r9 : 00000000 r8 : c0c49178
r7 : 00000000 r6 : cdc14718 r5 : ce762800 r4 : cdc14710
r3 : 00000000 r2 : 00000054 r1 : 00000000 r0 : cdc14718
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 18c5387d Table: 0000404a DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xce4ca210)
...
[<c074bc68>] (memcpy) from [<c0529548>] (xgmiitorgmii_probe+0x90/0xe8)
[<c0529548>] (xgmiitorgmii_probe) from [<c0526a94>] (mdio_probe+0x28/0x34)
[<c0526a94>] (mdio_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbd58>] (__device_attach_driver+0xac/0x10c)
[<c04dbd58>] (__device_attach_driver) from [<c04d96f4>] (bus_for_each_drv+0x84/0xc8)
[<c04d96f4>] (bus_for_each_drv) from [<c04db5bc>] (__device_attach+0xd0/0x134)
[<c04db5bc>] (__device_attach) from [<c04dbdd4>] (device_initial_probe+0x1c/0x20)
[<c04dbdd4>] (device_initial_probe) from [<c04da8fc>] (bus_probe_device+0x98/0xa0)
[<c04da8fc>] (bus_probe_device) from [<c04d8660>] (device_add+0x43c/0x5d0)
[<c04d8660>] (device_add) from [<c0526cb8>] (mdio_device_register+0x34/0x80)
[<c0526cb8>] (mdio_device_register) from [<c0580b48>] (of_mdiobus_register+0x170/0x30c)
[<c0580b48>] (of_mdiobus_register) from [<c05349c4>] (macb_probe+0x710/0xc00)
[<c05349c4>] (macb_probe) from [<c04dd700>] (platform_drv_probe+0x44/0x80)
[<c04dd700>] (platform_drv_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbc58>] (__driver_attach+0x10c/0x118)
[<c04dbc58>] (__driver_attach) from [<c04d9600>] (bus_for_each_dev+0x8c/0xd0)
[<c04d9600>] (bus_for_each_dev) from [<c04db1fc>] (driver_attach+0x2c/0x30)
[<c04db1fc>] (driver_attach) from [<c04daa98>] (bus_add_driver+0x50/0x260)
[<c04daa98>] (bus_add_driver) from [<c04dc440>] (driver_register+0x88/0x108)
[<c04dc440>] (driver_register) from [<c04dd6b4>] (__platform_driver_register+0x50/0x58)
[<c04dd6b4>] (__platform_driver_register) from [<c0b31248>] (macb_driver_init+0x24/0x28)
[<c0b31248>] (macb_driver_init) from [<c010203c>] (do_one_initcall+0x60/0x1a4)
[<c010203c>] (do_one_initcall) from [<c0b00f78>] (kernel_init_freeable+0x15c/0x1f8)
[<c0b00f78>] (kernel_init_freeable) from [<c0763d10>] (kernel_init+0x18/0x124)
[<c0763d10>] (kernel_init) from [<c0112d74>] (ret_from_fork+0x14/0x20)
Code: ba000002 f5d1f03c f5d1f05c f5d1f07c (e8b151f8)
---[ end trace 3e4ec21905820a1f ]---
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 168f75f11f ]
While debugging driver crashes related to a buggy firmware
crashing under load, I noticed that ath10k_htt_rx_ring_free
could be called without being under lock. I'm not sure if this
is the root cause of the crash or not, but it seems prudent to
protect it.
Originally tested on 4.16+ kernel with ath10k-ct 10.4 firmware
running on 9984 NIC.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8d0752d113 ]
We're ignoring the result of the attached phy device's read_status().
Return it so we can detect errors.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8530b4e7b2 ]
Without this, packets larger than 1500 will silently be dropped.
Easily reproduced by sending a ping packet with a size larger
than 1500.
Co-Developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 679e1f07c8 ]
All packets in a bundle should use the same endpoint id as the
first lookahead.
This matches how things are done is ath6kl, however,
this patch can theoretically handle several bundles
in ath10k_sdio_mbox_rx_process_packets().
Without this patch we get lots of errors about invalid endpoint id:
ath10k_sdio mmc2:0001:1: invalid endpoint in look-ahead: 224
ath10k_sdio mmc2:0001:1: failed to get pending recv messages: -12
ath10k_sdio mmc2:0001:1: failed to process pending SDIO interrupts: -12
Co-Developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad4f15dc2c upstream.
Commit 57f230ab04 ("xen/netfront: raise max number of slots in
xennet_get_responses()") raised the max number of allowed slots by one.
This seems to be problematic in some configurations with netback using
a larger MAX_SKB_FRAGS value (e.g. old Linux kernel with MAX_SKB_FRAGS
defined as 18 instead of nowadays 17).
Instead of BUG_ON() in this case just fall back to retransmission.
Fixes: 57f230ab04 ("xen/netfront: raise max number of slots in xennet_get_responses()")
Cc: stable@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 922005c7f5 ]
Recent firmware revisions have added the ability to force
these modems to USB2 mode, hiding their SuperSpeed
capabilities from the host. The driver has been using the
SuperSpeed capability, as shown by the bcdUSB field of the
device descriptor, to detect the need to enable the DTR
quirk. This method fails when the modems are forced to
USB2 mode by the modem firmware.
Fix by unconditionally enabling the DTR quirk for the
affected device IDs.
Reported-by: Fred Veldini <fred.veldini@gmail.com>
Reported-by: Deshu Wen <dwen@sierrawireless.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reported-by: Fred Veldini <fred.veldini@gmail.com>
Reported-by: Deshu Wen <dwen@sierrawireless.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a7f38002fb ]
The operation ~(p100_inb(VG_LAN_CFG_1) & HP100_LINK_UP) returns a value
that is always non-zero and hence the wait for the link to drop always
terminates prematurely. Fix this by using a logical not operator instead
of a bitwise complement. This issue has been in the driver since
pre-2.6.12-rc2.
Detected by CoverityScan, CID#114157 ("Logical vs. bitwise operator")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9824dfae57 ]
Fields ->dev and ->next of struct ipddp_route may be copied to
userspace on the SIOCFINDIPDDPRT ioctl. This is only accessible
to CAP_NET_ADMIN though. Let's manually copy the relevant fields
instead of using memcpy().
BugLink: http://blog.infosectcbr.com.au/2018/09/linux-kernel-infoleaks.html
Cc: Jann Horn <jannh@google.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e7dc08e57 upstream.
When autoneg is off, the .check_for_link callback functions clear the
get_link_status flag and systematically return a "pseudo-error". This means
that the link is not detected as up until the next execution of the
e1000_watchdog_task() 2 seconds later.
Fixes: 19110cfbb3 ("e1000e: Separate signaling for link check/link up")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2710dbf0d upstream.
Alex reported the following race condition:
/* link goes up... interrupt... schedule watchdog */
\ e1000_watchdog_task
\ e1000e_has_link
\ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
\ e1000e_phy_has_link_generic(..., &link)
link = true
/* link goes down... interrupt */
\ e1000_msix_other
hw->mac.get_link_status = true
/* link is up */
mac->get_link_status = false
link_active = true
/* link_active is true, wrongly, and stays so because
* get_link_status is false */
Avoid this problem by making sure that we don't set get_link_status = false
after having checked the link.
It seems this problem has been present since the introduction of e1000e.
Link: https://lkml.org/lkml/2018/1/29/338
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3016e0a0c9 upstream.
This reverts commit 19110cfbb3.
This reverts commit 4110e02eb4.
This reverts commit d3604515c9eda464a92e8e67aae82dfe07fe3c98.
Commit 19110cfbb3 ("e1000e: Separate signaling for link check/link up")
changed what happens to the link status when there is an error which
happens after "get_link_status = false" in the copper check_for_link
callbacks. Previously, such an error would be ignored and the link
considered up. After that commit, any error implies that the link is down.
Revert commit 19110cfbb3 ("e1000e: Separate signaling for link check/link
up") and its followups. After reverting, the race condition described in
the log of commit 19110cfbb3 is reintroduced. It may still be triggered
by LSC events but this should keep the link down in case the link is
electrically unstable, as discussed. The race may no longer be
triggered by RXO events because commit 4aea7a5c5e ("e1000e: Avoid
receiver overrun interrupt bursts") restored reading icr in the Other
handler.
Link: https://lkml.org/lkml/2018/3/1/789
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 116f4a640b upstream.
The 82574 specification update errata 12 states that interrupts may be
missed if ICR is read while INT_ASSERTED is not set. Avoid that problem by
setting all bits related to events that can trigger the Other interrupt in
IMS.
The Other interrupt is raised for such events regardless of whether or not
they are set in IMS. However, only when they are set is the INT_ASSERTED
bit also set in ICR.
By doing this, we ensure that INT_ASSERTED is always set when we read ICR
in e1000_msix_other() and steer clear of the errata. This also ensures that
ICR will automatically be cleared on read, therefore we no longer need to
clear bits explicitly.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 361a954e6a upstream.
Restores the ICS write for Rx/Tx queue interrupts which was present before
commit 16ecba59bc ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1)
but was not restored in commit 4aea7a5c5e
("e1000e: Avoid receiver overrun interrupt bursts", v4.15-rc1).
This re-raises the queue interrupts in case the txq or rxq bits were set in
ICR and the Other interrupt handler read and cleared ICR before the queue
interrupt was raised.
Fixes: 4aea7a5c5e ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f0ea19722 upstream.
This partially reverts commit 4aea7a5c5e.
We keep the fix for the first part of the problem (1) described in the log
of that commit, that is to read ICR in the other interrupt handler. We
remove the fix for the second part of the problem (2), Other interrupt
throttling.
Bursts of "Other" interrupts may once again occur during rxo (receive
overflow) traffic conditions. This is deemed acceptable in the interest of
avoiding unforeseen fallout from changes that are not strictly necessary.
As discussed, the e1000e driver should be in "maintenance mode".
Link: https://www.spinics.net/lists/netdev/msg480675.html
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 745d0bd3af upstream.
It was reported that emulated e1000e devices in vmware esxi 6.5 Build
7526125 do not link up after commit 4aea7a5c5e ("e1000e: Avoid receiver
overrun interrupt bursts", v4.15-rc1). Some tracing shows that after
e1000e_trigger_lsc() is called, ICR reads out as 0x0 in e1000_msix_other()
on emulated e1000e devices. In comparison, on real e1000e 82574 hardware,
icr=0x80000004 (_INT_ASSERTED | _LSC) in the same situation.
Some experimentation showed that this flaw in vmware e1000e emulation can
be worked around by not setting Other in EIAC. This is how it was before
16ecba59bc ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1).
Fixes: 4aea7a5c5e ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ac13d6d8ea ]
When configuring SLI_PKTn_OUTPUT_CONTROL, VF driver was assuming that IPTR
mode was disabled by reset, which was not true. Since DPDK driver had
set IPTR mode previously, the VF driver (which uses buf-ptr-only mode) was
not properly handling DROQ packets (i.e. it saw zero-length packets).
This represented an invalid hardware configuration which the driver could
not handle.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8edfe2e992 upstream.
Commit 822fb18a82 ("xen-netfront: wait xenbus state change when load
module manually") added a new wait queue to wait on for a state change
when the module is loaded manually. Unfortunately there is no wakeup
anywhere to stop that waiting.
Instead of introducing a new wait queue rename the existing
module_unload_q to module_wq and use it for both purposes (loading and
unloading).
As any state change of the backend might be intended to stop waiting
do the wake_up_all() in any case when netback_changed() is called.
Fixes: 822fb18a82 ("xen-netfront: wait xenbus state change when load module manually")
Cc: <stable@vger.kernel.org> #4.18
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2d408c0d45 ]
Commit f599c64fdf ("xen-netfront: Fix race between device setup and
open") changed the initialization order: xennet_create_queues() now
happens before we do register_netdev() so using netdev->name in
xennet_init_queue() is incorrect, we end up with the following in
/proc/interrupts:
60: 139 0 xen-dyn -event eth%d-q0-tx
61: 265 0 xen-dyn -event eth%d-q0-rx
62: 234 0 xen-dyn -event eth%d-q1-tx
63: 1 0 xen-dyn -event eth%d-q1-rx
and this looks ugly. Actually, using early netdev name (even when it's
already set) is also not ideal: nowadays we tend to rename eth devices
and queue name may end up not corresponding to the netdev name.
Use nodename from xenbus device for queue naming: this can't change in VM's
lifetime. Now /proc/interrupts looks like
62: 202 0 xen-dyn -event device/vif/0-q0-tx
63: 317 0 xen-dyn -event device/vif/0-q0-rx
64: 262 0 xen-dyn -event device/vif/0-q1-tx
65: 17 0 xen-dyn -event device/vif/0-q1-rx
Fixes: f599c64fdf ("xen-netfront: Fix race between device setup and open")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07300f774f ]
After device is stopped we reset the rings by moving all free buffers
to positions [0, cnt - 2], and clear the position cnt - 1 in the ring.
We then proceed to clear the read/write pointers. This means that if
we try to reset the ring again the code will assume that the next to
fill buffer is at position 0 and swap it with cnt - 1. Since we
previously cleared position cnt - 1 it will lead to leaking the first
buffer and leaving ring in a bad state.
This scenario can only happen if FW communication fails, in which case
the ring will never be used again, so the fact it's in a bad state will
not be noticed. Buffer leak is the only problem. Don't try to move
buffers in the ring if the read/write pointers indicate the ring was
never used or have already been reset.
nfp_net_clear_config_and_disable() is now fully idempotent.
Found by code inspection, FW communication failures are very rare,
and reconfiguring a live device is not common either, so it's unlikely
anyone has ever noticed the leak.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fd800f6464 ]
qe_muram_alloc return a unsigned long integer,which should not
compared with zero. check it using IS_ERR_VALUE() to fix this.
Fixes: c19b6d246a ("drivers/net: support hdlc function for QE-UCC")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b24dbfe9ce ]
The dma_mapping_error() returns true or false, but we want
to return -ENOMEM if there was an error.
Fixes: 174fd2597b ("amd-xgbe: Implement split header receive support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b19b46346f upstream.
The recent commit 916c5e1413 ("hv/netvsc: fix handling of fallback
to single queue mode") tried to fix the fallback behavior to a single
queue mode, but it changed the function to return zero incorrectly,
while the function should return an object pointer. Eventually this
leads to a NULL dereference at the callers that expect non-NULL
value.
Fix it by returning the proper net_device object.
Fixes: 916c5e1413 ("hv/netvsc: fix handling of fallback to single queue mode")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Alakesh Haloi <alakeshh@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c88a026e01 ]
The memory allocated for the slow path table flow group input structure
was not freed upon successful return, fix that.
Fixes: 1967ce6ea5 ("net/mlx5: E-Switch, Refactor fast path FDB table creation in switchdev mode")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5df816e7f4 ]
When initializing the device (procedure init_one), the driver
calls mlx5_pci_init to perform pci initialization. As part of this
initialization, mlx5_pci_init creates a debugfs directory.
If this creation fails, init_one aborts, returning failure to
the caller (which is the probe method caller).
The main reason for such a failure to occur is if the debugfs
directory already exists. This can happen if the last time
mlx5_pci_close was called, debugfs_remove (silently) failed due
to the debugfs directory not being empty.
Guarantee that such a debugfs_remove failure will not occur by
instead calling debugfs_remove_recursive in procedure mlx5_pci_close.
Fixes: 59211bd3b6 ("net/mlx5: Split the load/unload flow into hardware and software flows")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47bc94b822 ]
Currently, mlx5_attach_interface does not check for error
after calling intf->attach or intf->add. When these two calls
fails, the client is not initialized and will cause issues such as
kernel panic on invalid address in the teardown path (mlx5_detach_interface)
Fixes: 737a234bb6 ("net/mlx5: Introduce attach/detach to interface API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e65a9e480e ]
With performance optimization the spi transfer and messages of basic
register operations like qcaspi_read_register moved into the private
driver structure. But they weren't protected against mutual access
(e.g. between driver kthread and ethtool). So dumping the QCA7000
registers via ethtool during network traffic could make spi_sync
hang forever, because the completion in spi_message is overwritten.
So revert the optimization completely.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA700")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 76d5581c87 ]
When the mlx5 health mechanism detects a problem while the driver
is in the middle of init_one or remove_one, the driver needs to prevent
the health mechanism from scheduling future work; if future work
is scheduled, there is a problem with use-after-free: the system WQ
tries to run the work item (which has been freed) at the scheduled
future time.
Prevent this by disabling work item scheduling in the health mechanism
when the driver is in the middle of init_one() or remove_one().
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9d7f19dc46 ]
DMA allocated memory is lost in be_cmd_get_profile_config() when we
call it with non-NULL port_res parameter.
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7063efd33b upstream.
After commit b196d88aba ("tun: fix use after free for ptr_ring") we
need clean up tx ring during release(). But unfortunately, it tries to
do the cleanup blindly after socket were destroyed which will lead
another use-after-free. Fix this by doing the cleanup before dropping
the last reference of the socket in __tun_detach().
Backport Note :-
Upstream commit moves the ptr_ring_cleanup call from tun_chr_close to
__tun_detach. Upstream applied that patch after replacing skb_array with
ptr_ring. This patch moves the skb_array_cleanup call from
tun_chr_close to __tun_detach.
Reported-by: Andrei Vagin <avagin@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Fixes: b196d88aba ("tun: fix use after free for ptr_ring")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zubin Mithra <zsm@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b196d88aba upstream.
We used to initialize ptr_ring during TUNSETIFF, this is because its
size depends on the tx_queue_len of netdevice. And we try to clean it
up when socket were detached from netdevice. A race were spotted when
trying to do uninit during a read which will lead a use after free for
pointer ring. Solving this by always initialize a zero size ptr_ring
in open() and do resizing during TUNSETIFF, and then we can safely do
cleanup during close(). With this, there's no need for the workaround
that was introduced by commit 4df0bfc799 ("tun: fix a memory leak
for tfile->tx_array").
Backport Note :-
Comparison with the upstream patch:
[1] A "semantic revert" of the changes made in
4df0bfc799("tun: fix a memory leak for tfile->tx_array").
4df0bfc799 was applied upstream, and then skb array was changed
to use ptr_ring. The upstream patch then removes the changes introduced
by 4df0bfc799. This backport does the same; "revert" the changes
made by 4df0bfc799.
[2] xdp_rxq_info_unreg() being called in relevant locations
As xdp_rxq_info related patches are not present in 4.14, these
changes are not needed in the backport.
[3] An instance of ptr_ring_init needs to be replaced by skb_array_init
Inside tun_attach()
[4] ptr_ring_cleanup needs to be replaced by skb_array_cleanup
Inside tun_chr_close()
Note that the backport for 7063efd33b ("tuntap: fix use after free during release")
needs to be applied on top of this patch.
Reported-by: syzbot+e8b902c3c3fadf0a9dba@syzkaller.appspotmail.com
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Fixes: 1576d98605 ("tun: switch to use skb array for tx")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zubin Mithra <zsm@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8466baf788 ]
It is incorrect to enable TX/RX queues (call by mvneta_port_up()) for
port without link. Indeed MTU change for interface without link causes TX
queues to stuck.
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP
network unit")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
[gregory.clement: adding Fixes tags and rewording commit log]
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 673bc519c5 ]
The tx completion of multiple mgmt frames can be bundled
in a single event and sent by the firmware to host, if this
capability is not disabled explicitly by the host. If the host
cannot handle the bundled mgmt tx completion, this capability
support needs to be disabled in the wmi init cmd, sent to the firmware.
Add the host capability indication flag in the wmi ready command,
to let firmware know the features supported by the host driver.
This field is ignored if it is not supported by firmware.
Set the host capability indication flag(i.e. host_capab) to zero,
for disabling the support of bundle mgmt tx completion. This will
indicate the firmware to send completion event for every mgmt tx
completion, instead of bundling them together and sending in a single
event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 37a634f60f ]
When receiving a beacon or probe response, we should update the
boottime_ns field which is the timestamp the frame was received at.
(cf mac80211.h)
This fixes a scanning issue with Android since it relies on this
timestamp to determine when the AP has been seen for the last time
(via the nl80211 BSS_LAST_SEEN_BOOTTIME parameter).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f25911158 ]
The QCA4019 hw1.0 firmware 10.4-3.2.1-00050 and 10.4-3.5.3-00053 (and most
likely all other) seem to ignore the WMI_CHAN_FLAG_DFS flag during the
scan. This results in transmission (probe requests) on channels which are
not "available" for transmissions.
Since the firmware is closed source and nothing can be done from our side
to fix the problem in it, the driver has to work around this problem. The
WMI_CHAN_FLAG_PASSIVE seems to be interpreted by the firmware to not
scan actively on a channel unless an AP was detected on it. Simple probe
requests will then be transmitted by the STA on the channel.
ath10k must therefore also use this flag when it queues a radar channel for
scanning. This should reduce the chance of an active scan when the channel
might be "unusable" for transmissions.
Fixes: e8a50f8ba4 ("ath10k: introduce DFS implementation")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 461d8a6bb9 ]
The tx power applied by set_txpower is limited by the CTL (conformance
test limit) entries in the EEPROM. These can change based on the user
configured regulatory domain.
Depending on the EEPROM data this can cause the tx power to become too
limited, if the original regdomain CTLs impose lower limits than the CTLs
of the user configured regdomain.
To fix this issue, set the initial channel limits without any CTL
restrictions and only apply the CTL at run time when setting the channel
and the real tx power.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 36e14a787d ]
Fixes missed indications of end of U-APSD service period to mac80211
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 77fefa93bf ]
Modify the register offsets in the Broadcom iProc mdio mux to start
from the top of the register address space.
Earlier, the base address pointed to the end of the block's register
space. The base address will now point to the start of the mdio's
address space. The offsets have been fixed to match this.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 60081dcc4f ]
For marvell phy m88e1510, bit SUPPORTED_FIBRE of phydev->supported
is default on. Both phy_resume() and phy_suspend() will check the
SUPPORTED_FIBRE bit and write register of fibre page.
Currently in hns3 driver, the SUPPORTED_FIBRE bit will be cleared
after phy_connect_direct() finished. Because phy_resume() is called
in phy_connect_direct(), and phy_suspend() is called when disconnect
phy device, so the operation for fibre page register is not symmetrical.
It will cause phy link issue when reload hns3 driver.
This patch fixes it by disable the SUPPORTED_FIBRE before connecting
phy.
Fixes: 256727da73 ("net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c39d5278e ]
According to the functional specification of hardware, the first
descriptor of response from command 'lookup vlan talbe' is not valid.
Currently, the first descriptor is parsed as normal value, which will
cause an expected error.
This patch fixes this problem by skipping the first descriptor.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e04e7a7bbd ]
This patch fixes the race between netvsc_probe() and
rndis_set_subchannel(), which can cause a deadlock.
These are the related 3 paths which show the deadlock:
path #1:
Workqueue: hv_vmbus_con vmbus_onmessage_work [hv_vmbus]
Call Trace:
schedule
schedule_preempt_disabled
__mutex_lock
__device_attach
bus_probe_device
device_add
vmbus_device_register
vmbus_onoffer
vmbus_onmessage_work
process_one_work
worker_thread
kthread
ret_from_fork
path #2:
schedule
schedule_preempt_disabled
__mutex_lock
netvsc_probe
vmbus_probe
really_probe
__driver_attach
bus_for_each_dev
driver_attach_async
async_run_entry_fn
process_one_work
worker_thread
kthread
ret_from_fork
path #3:
Workqueue: events netvsc_subchan_work [hv_netvsc]
Call Trace:
schedule
rndis_set_subchannel
netvsc_subchan_work
process_one_work
worker_thread
kthread
ret_from_fork
Before path #1 finishes, path #2 can start to run, because just before
the "bus_probe_device(dev);" in device_add() in path #1, there is a line
"object_uevent(&dev->kobj, KOBJ_ADD);", so systemd-udevd can
immediately try to load hv_netvsc and hence path #2 can start to run.
Next, path #2 offloads the subchannal's initialization to a workqueue,
i.e. path #3, so we can end up in a deadlock situation like this:
Path #2 gets the device lock, and is trying to get the rtnl lock;
Path #3 gets the rtnl lock and is waiting for all the subchannel messages
to be processed;
Path #1 is trying to get the device lock, but since #2 is not releasing
the device lock, path #1 has to sleep; since the VMBus messages are
processed one by one, this means the sub-channel messages can't be
procedded, so #3 has to sleep with the rtnl lock held, and finally #2
has to sleep... Now all the 3 paths are sleeping and we hit the deadlock.
With the patch, we can make sure #2 gets both the device lock and the
rtnl lock together, gets its job done, and releases the locks, so #1
and #3 will not be blocked for ever.
Fixes: 8195b1396e ("hv_netvsc: fix deadlock on hotplug")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b93c1b5ac8 ]
Registering another device with same MAC address (such as TAP, VPN or
DPDK KNI) will confuse the VF autobinding logic. Restrict the search
to only run if the device is known to be a PCI attached VF.
Fixes: e8ff40d4bf ("hv_netvsc: improve VF device matching")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 602b74eda8 ]
When a bridge device is removed, the VLANs are flushed from each
configured port. This causes the ports to decrement the reference count
on the associated FIDs (filtering identifier). If the reference count of
a FID is 1 and it has a RIF (router interface), then this RIF is
destroyed.
However, if no port is member in the VLAN for which a RIF exists, then
the RIF will continue to exist after the removal of the bridge. To
reproduce:
# ip link add name br0 type bridge vlan_filtering 1
# ip link set dev swp1 master br0
# ip link add link br0 name br0.10 type vlan id 10
# ip address add 192.0.2.0/24 dev br0.10
# ip link del dev br0
The RIF associated with br0.10 continues to exist.
Fix this by iterating over all the bridge device uppers when it is
destroyed and take care of destroying their RIFs.
Fixes: 99f44bb352 ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ad716b95f ]
To avoid leaking a running timer we need to wait for the
posted reconfigs after netdev is unregistered. In common
case the process of deinitializing the device will perform
synchronous reconfigs which wait for posted requests, but
especially with VXLAN ports being actively added and removed
there can be a race condition leaving a timer running after
adapter structure is freed leading to a crash.
Add an explicit flush after deregistering and for a good
measure a warning to check if timer is running just before
structures are freed.
Fixes: 3d780b926a ("nfp: add async reconfiguration mechanism")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9fd0e09a4e ]
This card identifies itself as:
Ethernet controller [0200]: NCube Device [10ff:8168] (rev 06)
Subsystem: TP-LINK Technologies Co., Ltd. Device [7470:3468]
Adding a new entry to rtl8169_pci_tbl makes the card work.
Link: http://launchpad.net/bugs/1788730
Signed-off-by: Anthony Wong <anthony.wong@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6750c87074 ]
qlge_fix_features() is not supposed to modify hardware or
driver state, rather it is supposed to only fix requested
fetures bits. Currently qlge_fix_features() also goes for
interface down and up unnecessarily if there is not even
any change in features set.
This patch changes/fixes following -
1) Move reload of interface or device re-config from
qlge_fix_features() to qlge_set_features().
2) Reload of interface in qlge_set_features() only if
relevant feature bit (NETIF_F_HW_VLAN_CTAG_RX) is changed.
3) Get rid of qlge_fix_features() since driver is not really
required to fix any features bit.
Signed-off-by: Manish <manish.chopra@cavium.com>
Reviewed-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0da70f8080 ]
macb_reset_hw() is called from macb_close() and indirectly from
macb_open(). macb_reset_hw() zeroes the NCR register, including the MPE
(Management Port Enable) bit.
This will prevent accessing any other PHYs for other Ethernet MACs on
the MDIO bus, which remains registered at macb_reset_hw() time, until
macb_init_hw() is called from macb_open() which sets the MPE bit again.
I.e. currently the MDIO bus has a short disruption at open time and is
disabled at close time until the interface is opened again.
Fix that by only touching the RE and TE bits when enabling and disabling
RX/TX.
v2: Make macb_init_hw() NCR write a single statement.
Fixes: 6c36a70744 ("macb: Use generic PHY layer")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c3c397c1f1 ]
When using the fixed PHY with GENET (e.g. MOCA) the PHY link
status can be determined from the internal link status captured
by the MAC. This allows the PHY state machine to use the correct
link state with the fixed PHY even if MAC link event interrupts
are missed when the net device is opened.
Fixes: 8d88c6ebb3 ("net: bcmgenet: enable MoCA link state change detection")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7444a80929 upstream.
Prior to commit 573185cc7e ("mmc: core: Invoke sdio func driver's PM
callbacks from the sdio bus"), the MMC core used to call into the power
management functions of SDIO clients itself and removed the card if the
return code was non-zero. IOW, the mmc handled errors gracefully and didn't
upchain them to the pm core.
Since this change, the mmc core relies on generic power management
functions which treat all errors as a reason to cancel the suspend
immediately. This causes suspend attempts to fail when the libertas
driver is loaded.
To fix this, power down the card explicitly in if_sdio_suspend() when we
know we're about to lose power and return success. Also set a flag in these
cases, and power up the card again in if_sdio_resume().
Fixes: 573185cc7e ("mmc: core: Invoke sdio func driver's PM callbacks from the sdio bus")
Cc: <stable@vger.kernel.org>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Chris Ball <chris@printf.net>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2aa650d195 upstream.
strncpy might not NUL-terminate the string, if the name equals the buffer size.
Use strlcpy instead.
Signed-off-by: Michael Buesch <m@bues.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d77a89e39 upstream.
strncpy might not NUL-terminate the string, if the name equals the buffer size.
Use strlcpy instead.
Signed-off-by: Michael Buesch <m@bues.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit afb41bb039 ]
Current value for a target abort error is 0x010, however, this value
should in fact be 0x002. As it stands, the range of error is 0..7 so
it is currently never being detected. This bug has been in the driver
since the early 2.6.12 days (or before).
Detected by CoverityScan, CID#744290 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cb5c656886 ]
In commit ab123fe071 ("enic: handle mtu change for vf properly")
ASSERT_RTNL() is added to _enic_change_mtu() to prevent it from being
called without rtnl held. enic_probe() calls enic_change_mtu()
without rtnl held. At this point netdev is not registered yet.
Remove call to enic_change_mtu and assign the mtu to netdev->mtu.
Fixes: ab123fe071 ("enic: handle mtu change for vf properly")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ab123fe071 ]
When driver gets notification for mtu change, driver does not handle it for
all RQs. It handles only RQ[0].
Fix is to use enic_change_mtu() interface to change mtu for vf.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee614c8710 ]
Function nfp_flower_repr_get_type_and_port expects an enum nfp_repr_type
return value but, if the repr type is unknown, returns a value of type
enum nfp_flower_cmsg_port_type. This means that if FW encodes the port
ID in a way the driver does not understand instead of dropping the frame
driver may attribute it to a physical port (uplink) provided the port
number is less than physical port count.
Fix this and ensure a net_device of NULL is returned if the repr can not
be determined.
Fixes: 1025351a88 ("nfp: add flower app")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7856e86162 ]
Otherwise interfaces get exposed under /sys/devices/virtual, which
doesn't give udev the context it needs for PCI-based predictable
interface names.
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ae2dcb28c2 ]
Rx hash/filter table configuration uses rss_conf_obj to configure filters
in the hardware. This object is initialized only when the interface is
brought up.
This patch adds driver changes to configure rss params only when the device
is in opened state. In port disabled case, the config will be cached in the
driver structure which will be applied in the successive load path.
Please consider applying it to 'net' branch.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 54e4a0c486 ]
MCAN message ram should only be accessed once clocks are enabled.
Therefore, move the call to parse/init the message ram to after
clocks are enabled.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5c1a23b17 ]
of_iomap() can return NULL so that return needs to be checked and NULL
treated as failure. While at it also take care of the missing
of_node_put() in the error path.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: commit afa17a500a ("net/can: add driver for mscan family & mpc52xx_mscan")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c9ce1fa1c2 ]
Prevent drivers from building on PPC32 if they use isa_bus_to_virt(),
isa_virt_to_bus(), or isa_page_to_bus(), which are not available and
thus cause build errors.
../drivers/net/ethernet/3com/3c515.c: In function 'corkscrew_open':
../drivers/net/ethernet/3com/3c515.c:824:9: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/lance.c: In function 'lance_rx':
../drivers/net/ethernet/amd/lance.c:1203:23: error: implicit declaration of function 'isa_bus_to_virt'; did you mean 'bus_to_virt'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/ni65.c: In function 'ni65_init_lance':
../drivers/net/ethernet/amd/ni65.c:585:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/cirrus/cs89x0.c: In function 'net_open':
../drivers/net/ethernet/cirrus/cs89x0.c:897:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 25c020a909 ]
FW hsi contains 256 approximation buckets which are split in ramrod into
eight u32 values, but driver is using eight 'unsigned long' variables.
This patch fixes the mcast logic by making the API utilize u32.
Fixes: 83aeb933 ("qed*: Trivial modifications")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 58874c7b24 ]
There's a possible race where driver can read link status in mid-transition
and see that virtual-link is up yet speed is 0. Since in this
mid-transition we're guaranteed to see a mailbox from MFW soon, we can
afford to treat this as link down.
Fixes: cc875c2e ("qed: Add link support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4ad95a93a7 ]
Apparently, MFW publishes EEE capabilities even for Fiber-boards that don't
support them, and later since qed internally sets adv_caps it would cause
link-flap avoidance (LFA) to fail when driver would initiate the link.
This in turn delays the link, causing traffic to fail.
Driver has been modified to not to ask MFW for any EEE config if EEE isn't
to be enabled.
Fixes: 645874e5 ("qed: Add support for Energy efficient ethernet.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5097399326 ]
In cases the probing fails the log level of the messages should
be an error.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 711c62dfa6 ]
In case the SPI thread is not running, a simple reset of sync
state won't fix the transmit timeout. We also need to wake up the kernel
thread.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: ed7d42e24e ("net: qca_spi: fix transmit queue timeout handling")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b2bab426dc ]
As long as the synchronization with the QCA7000 isn't finished, we
cannot accept packets from the upper layers. So let the SPI thread
enable the TX queue after sync and avoid unwanted packet drop.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3a9b045506 ]
This driver can spam the kernel log with multiple messages of:
net eth0: eth0: allmulti set
Usually 4 or 8 at a time (probably because of using ConnMan).
This message doesn't seem useful, so let's demote it from dev_info()
to dev_dbg().
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4aac0b4347 ]
octeon_mgmt driver doesn't drop RX frames that are 1-4 bytes bigger than
MTU set for the corresponding interface. The problem is in the
AGL_GMX_RX0/1_FRM_MAX register setting, which should not account for VLAN
tagging.
According to Octeon HW manual:
"For tagged frames, MAX increases by four bytes for each VLAN found up to a
maximum of two VLANs, or MAX + 8 bytes."
OCTEON_FRAME_HEADER_LEN "define" is fine for ring buffer management, but
should not be used for AGL_GMX_RX0/1_FRM_MAX.
The problem could be easily reproduced using "ping" command. If affected
system has default MTU 1500, other host (having MTU >= 1504) can
successfully "ping" the affected system with payload size 1473-1476,
resulting in IP packets of size 1501-1504 accepted by the mgmt driver.
Fixed system still accepts IP packets of 1500 bytes even with VLAN tagging,
because the limits are lifted in HW as expected, for every VLAN tag.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3578a7ecb6 ]
Testing has uncovered a failure case that is not handled properly. In the
event that a login fails and we are not able to recover on the spot, we
return 0 from do_reset, preventing any error recovery code from being
triggered. Additionally, the state is set to "probed" meaning that when we
are able to trigger the error recovery, the driver always comes up in the
probed state. To handle the case properly, we need to return a failure code
here and set the adapter state to the state that we entered the reset in
indicating the state that we would like to come out of the recovery reset
in.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 916c5e1413 ]
The netvsc device may need to fallback to running in single queue
mode if host side only wants to support single queue.
Recent change for handling mtu broke this in setup logic.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 3ffe64f1a6 ("hv_netvsc: split sub-channel setup into async and sync")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5fc853cc01 ]
We accidentally left out the error handling for kstrtoul().
Fixes: a520030e32 ("qlcnic: Implement flash sysfs callback for 83xx adapter")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d14c780c11 ]
This change makes it so that we are much more explicit about the ordering
of updates to the receive address register (RAR) table. Prior to this patch
I believe we may have been updating the table while entries were still
active, or possibly allowing for reordering of things since we weren't
explicitly flushing writes to either the lower or upper portion of the
register prior to accessing the other half.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c58387ab16 ]
Fix bug in the error code path when bnxt_request_irq() returns failure.
bnxt_disable_napi() should not be called in this error path because
NAPI has not been enabled yet.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78f058a4aa ]
The current code returns -ENOMEM and does not bother to set the output
parameters to 0 when no rings are available. Some callers, such as
bnxt_get_channels() will display garbage ring numbers when that happens.
Fix it by always setting the output parameters.
Fixes: 6e6c5a57fb ("bnxt_en: Modify bnxt_get_max_rings() to support shared or non shared rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07f4fde53d ]
If there aren't enough RX rings available, the driver will attempt to
use a single RX ring without the aggregation ring. If that also
fails, the BNXT_FLAG_AGG_RINGS flag is cleared but the other ring
parameters are not set consistently to reflect that. If more RX
rings become available at the next open, the RX rings will be in
an inconsistent state and may crash when freeing the RX rings.
Fix it by restoring the BNXT_FLAG_AGG_RINGS if not enough RX rings are
available to run without aggregation rings.
Fixes: bdbd1eb59c ("bnxt_en: Handle no aggregation ring gracefully.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8f2fbc6c60 ]
The check is valid but it does not warrant to crash the kernel. A
WARN_ON() is good enough here.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a81388ec2 ]
Instead of having the function name hard-coded (it might change and we
forgot to update them in the debug output) we can use __func__ instead
and also shorter the line so we do not need to break it. Also fix an
extra blank line while being here.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20f330452a ]
The check is valid but it does not warrant to crash the kernel. A
WARN_ON() is good enough here.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 05925e52a7 ]
The change fixes sleep in atomic context bug, which is encountered
every time when link settings are changed by ethtool.
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however that helper function is
called in atomic context under a grabbed spinlock, because
phy_start_aneg() is called by phy_ethtool_ksettings_set() and by
replaced phy_ethtool_sset() helpers from phylib.
Now duplex mode setting is enforced in ravb_adjust_link() only, also
now RX/TX is disabled when link is put down or modifications to E-MAC
registers ECMR and GECMR are expected for both cases of checked and
ignored link status pin state from E-MAC interrupt handler.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0973a4dd79 ]
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however the helper function is
called in atomic context.
The bug can be reproduced by running "ethtool -r" command, the bug
is reported if CONFIG_DEBUG_ATOMIC_SLEEP build option is enabled.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5cb3f52a11 ]
The change fixes sleep in atomic context bug, which is encountered
every time when link settings are changed by ethtool.
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however that helper function is
called in atomic context under a grabbed spinlock, because
phy_start_aneg() is called by phy_ethtool_ksettings_set() and by
replaced phy_ethtool_sset() helpers from phylib.
Now duplex mode setting is enforced in sh_eth_adjust_link() only,
also now RX/TX is disabled when link is put down or modifications
to E-MAC registers ECMR and GECMR are expected for both cases of
checked and ignored link status pin state from E-MAC interrupt handler.
For reference the change is a partial rework of commit 1e1b812bbe
("sh_eth: fix handling of no LINK signal").
Fixes: dc19e4e5e0 ("sh: sh_eth: Add support ethtool")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 53a710b504 ]
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however the helper function is
called in atomic context.
The bug can be reproduced by running "ethtool -r" command, the bug
is reported if CONFIG_DEBUG_ATOMIC_SLEEP build option is enabled.
Fixes: dc19e4e5e0 ("sh: sh_eth: Add support ethtool")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d461e3da90 ]
In certain conditions, the device may not be able to link in gigabit mode. This software workaround ensures that the device will not enter the failure state.
Fixes: d0cad87170 ("SMSC75XX USB 2.0 Gigabit Ethernet Devices")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5dc2d3996a ]
After we change the ipvlan mode from l3 to l2, or vice versa, we only
reset IFF_NOARP flag, but don't flush the ARP table cache, which will
cause eth->h_dest to be equal to eth->h_source in ipvlan_xmit_mode_l2().
Then the message will not come out of host.
Here is the reproducer on local host:
ip link set eth1 up
ip addr add 192.168.1.1/24 dev eth1
ip link add link eth1 ipvlan1 type ipvlan mode l3
ip netns add net1
ip link set ipvlan1 netns net1
ip netns exec net1 ip link set ipvlan1 up
ip netns exec net1 ip addr add 192.168.2.1/24 dev ipvlan1
ip route add 192.168.2.0/24 via 192.168.1.2
ping 192.168.2.2 -c 2
ip netns exec net1 ip link set ipvlan1 type ipvlan mode l2
ping 192.168.2.2 -c 2
Add the same configuration on remote host. After we set the mode to l2,
we could find that the src/dst MAC addresses are the same on eth1:
21:26:06.648565 00:b7:13:ad:d3:05 > 00:b7:13:ad:d3:05, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 58356, offset 0, flags [DF], proto ICMP (1), length 84)
192.168.2.1 > 192.168.2.2: ICMP echo request, id 22686, seq 1, length 64
Fix this by calling dev_change_flags(), which will call netdevice notifier
with flag change info.
v2:
a) As pointed out by Wang Cong, check return value for dev_change_flags() when
change dev flags.
b) As suggested by Stefano and Sabrina, move flags setting before l3mdev_ops.
So we don't need to redo ipvlan_{, un}register_nf_hook() again in err path.
Reported-by: Jianlin Shi <jishi@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 595e802e53 ]
The DPAA HW requires that at least 256 bytes from the start of the
first scatter-gather table entry are allocated and accessible. The
hardware reads the maximum size the table can have in one access,
thus requiring that the allocation and mapping to be done for the
maximum size of 256B even if there is a smaller number of entries
in the table.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b95f6fbc8e ]
The FMan hardware parser needs to be configured to remove the
short frame padding from the checksum calculation, otherwise
short UDP and TCP frames are likely to be marked as having a
bad checksum.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 484c016d93 ]
Driver performs the internal reload when it receives tx-timeout event from
the OS. Internal reload might fail in some scenarios e.g., fatal HW issues.
In such cases OS still see the link, which would result in undesirable
functionalities such as re-generation of tx-timeouts.
The patch addresses this issue by indicating the link-down to OS when
tx-timeout is detected, and keeping the link in down state till the
internal reload is successful.
Please consider applying it to 'net' branch.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9191fc2a43 ]
In the case of Station connects to AP with narrower bandwidth at beginning.
And later the AP changes the bandwidth to winder bandwidth, the AP will
beacon with wider bandwidth IE, eg VHT20->VHT40->VHT80 or VHT40->VHT80.
Since the supported BANDWIDTH will be limited by the PHYMODE, so while
Station receives the bandwidth change request, it will also need to
reconfigure the PHYMODE setting to firmware instead of just configuring
the BANDWIDTH info, otherwise it'll trigger a firmware crash with
non-support bandwidth.
The issue was observed in WLAN.RM.4.4.1-00051-QCARMSWP-1, QCA6174 with
below scenario:
AP xxx changed bandwidth, new config is 5200 MHz, width 2 (5190/0 MHz)
disconnect from AP xxx for new auth to yyy
RX ReassocResp from xxx (capab=0x1111 status=0 aid=102)
associated
....
AP xxx changed bandwidth, new config is 5200 MHz, width 2 (5190/0 MHz)
AP xxx changed bandwidth, new config is 5200 MHz, width 3 (5210/0 MHz)
....
firmware register dump:
[00]: 0x05030000 0x000015B3 0x00987291 0x00955B31
[04]: 0x00987291 0x00060730 0x00000004 0x00000001
[08]: 0x004089F0 0x00955A00 0x000A0B00 0x00400000
[12]: 0x00000009 0x00000000 0x00952CD0 0x00952CE6
[16]: 0x00952CC4 0x0098E25F 0x00000000 0x0091080D
[20]: 0x40987291 0x0040E7A8 0x00000000 0x0041EE3C
[24]: 0x809ABF05 0x0040E808 0x00000000 0xC0987291
[28]: 0x809A650C 0x0040E948 0x0041FE40 0x004345C4
[32]: 0x809A5C63 0x0040E988 0x0040E9AC 0x0042D1A8
[36]: 0x8091D252 0x0040E9A8 0x00000002 0x00000001
[40]: 0x809FDA9D 0x0040EA58 0x0043D554 0x0042D554
[44]: 0x809F8B22 0x0040EA78 0x0043D554 0x00000001
[48]: 0x80911210 0x0040EAC8 0x00000010 0x004041D0
[52]: 0x80911154 0x0040EB28 0x00400000 0x00000000
[56]: 0x8091122D 0x0040EB48 0x00000000 0x00400600
Reported-by: Rouven Czerwinski <rouven@czerwinskis.de>
Tested-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2d2595719a ]
sizeof() will return unsigned value so in the error check
negative error code will be always larger than sizeof().
Fixes: a0d8e02c35 ("nfp: add support for reading nffw info")
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a8d70a054a ]
In smartnic env, if the host (PF) driver is not an e-switch manager, we
are not allowed to apply eswitch ports setups such as vlan (VST),
spoof-checks, min/max rate or state.
Make sure we are eswitch manager when coming to issue these callbacks
and err otherwise.
Also fix the definition of ESW_ALLOWED to rely on eswitch_manager
capability and on the vport_group_manger.
Operations on the VF nic vport context, such as setting a mac or reading
the vport counters are allowed to the PF in this scheme.
The modify nic vport guid code was modified to omit checking the
nic_vport_node_guid_modify eswitch capability.
The reason for doing so is that modifying node guid requires vport group
manager capability, and there's no need to check further capabilities.
1. set_vf_vlan - disallowed
2. set_vf_spoofchk - disallowed
3. set_vf_mac - allowed
4. get_vf_config - allowed
5. set_vf_trust - disallowed
6. set_vf_rate - disallowed
7. get_vf_stat - allowed
8. set_vf_link_state - disallowed
Fixes: f942380c12 ('net/mlx5: E-Switch, Vport ingress/egress ACLs rules for spoofchk')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Tested-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ce36338a3 ]
When we are disabling DCB, store "0" in txq->dcb_prio
since that's used for future TX Work Request "OVLAN_IDX"
values. Setting non zero priority upon disabling DCB
would halt the traffic.
Reported-by: AMG Zollner Robert <robert@cloudmedia.eu>
CC: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea0820bb77 ]
Device tree based systems without of_dev_auxdata will have the mdio
device named differently than "davinci_mdio(.0)". In this case use the
device's parent's compatible string for matching
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bc8a2d9bcb ]
The Stratix10 platform has an additional reset line, OCP(Open Core Protocol),
that also needs to get deasserted for the stmmac ethernet controller to work.
Thus we need to update the Kconfig to include ARCH_STRATIX10 in order to build
dwmac-socfpga.
Also, remove the redundant check for the reset controller pointer. The
reset driver already checks for the pointer and returns 0 if the pointer
is NULL.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4e8439aa34 ]
The array bpq_eth_addr is only used to get the size of an
address, whereas the bcast_addr is used to set the broadcast
address. This leads to a warning when using clang:
drivers/net/hamradio/bpqether.c:94:13: warning: variable 'bpq_eth_addr' is not
needed and will not be emitted [-Wunneeded-internal-declaration]
static char bpq_eth_addr[6];
^
Remove both variables and use the common eth_broadcast_addr
to set the broadcast address.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3256d29fc7 ]
lockdep spotted that we are using rfs_h.lock in enic_get_rxnfc() without
initializing. rfs_h.lock is initialized in enic_open(). But ethtool_ops
can be called when interface is down.
Move enic_rfs_flw_tbl_init to enic_probe.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 18 PID: 1189 Comm: ethtool Not tainted 4.17.0-rc7-devel+ #27
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
Call Trace:
dump_stack+0x85/0xc0
register_lock_class+0x550/0x560
? __handle_mm_fault+0xa8b/0x1100
__lock_acquire+0x81/0x670
lock_acquire+0xb9/0x1e0
? enic_get_rxnfc+0x139/0x2b0 [enic]
_raw_spin_lock_bh+0x38/0x80
? enic_get_rxnfc+0x139/0x2b0 [enic]
enic_get_rxnfc+0x139/0x2b0 [enic]
ethtool_get_rxnfc+0x8d/0x1c0
dev_ethtool+0x16c8/0x2400
? __mutex_lock+0x64d/0xa00
? dev_load+0x6a/0x150
dev_ioctl+0x253/0x4b0
sock_do_ioctl+0x9a/0x130
sock_ioctl+0x1af/0x350
do_vfs_ioctl+0x8e/0x670
? syscall_trace_enter+0x1e2/0x380
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x5a/0x170
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ff54d5cd9e ]
Do not advertise DCBX_LLD_MANAGED capability i.e., do not allow
external agent to manage the dcbx/lldp negotiation. MFW acts as lldp agent
for qed* devices, and no other lldp agent is allowed to coexist with mfw.
Also updated a debug print, to not to display the redundant info.
Fixes: a1d8d8a51 ("qed: Add dcbnl support.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3935a70968 ]
Avoid calling a SIMD fastpath handler if it is NULL. The check is needed
to handle an unlikely scenario where unsolicited interrupt is destined to
a PF in INTa mode.
Fixes: fe56b9e6a ("qed: Add module with basic common support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f9de4df90 ]
Memory for packet buffers need to be freed in the error paths as there is
no consumer (e.g., upper layer) for such packets and that memory will never
get freed.
The issue was uncovered when port was attacked with flood of isatap
packets, these are multicast packets hence were directed at all the PFs.
For foce PF, this meant they were routed to the ll2 module which in turn
drops such packets.
Fixes: 0a7fb11c ("qed: Add Light L2 support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 11ba961c91 ]
It was noticed that NIC always pass all multicast traffic to the host
regardless of IFF_ALLMULTI flag on the interface.
The rule in MC Filter Table in NIC, that is configured to accept any
multicast packets, is turning on if IFF_MULTICAST flag is set on the
interface. It leads to passing all multicast traffic to the host.
This fix changes the condition to turn on that rule by checking
IFF_ALLMULTI flag as it should.
Fixes: b21f502f84 ("net:ethernet:aquantia: Fix for multicast filter handling.")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d472b3a6cf upstream.
skb_shinfo() can change when calling __pskb_pull_tail(): Don't cache
its return value.
Cc: stable@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72c05f32f4 upstream.
ems_usb_probe() allocates memory for dev->tx_msg_buffer, but there
is no its deallocation in ems_usb_disconnect().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f5991f36d ]
Execute mlx5_eswitch_init() only if we have MLX5_ESWITCH_MANAGER
capabilities.
Do the same for mlx5_eswitch_cleanup().
Fixes: a9f7705ffd ("net/mlx5: Unify vport manager capability check")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b7d0f08e91 ]
WoL won't work in PCI-based setups because we are not saving the PCI EP
state before entering suspend state and not allowing D3 wake.
Fix this by using a wrapper around stmmac_{suspend/resume} which
correctly sets the PCI EP state.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 822fb18a82 ]
When loading module manually, after call xenbus_switch_state to initializes
the state of the netfront device, the driver state did not change so fast
that may lead no dev created in latest kernel. This patch adds wait to make
sure xenbus knows the driver is not in closed/unknown state.
Current state:
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
[vm]# modprobe -r xen_netfront
[vm]# modprobe xen_netfront
[vm]# ethtool eth0
Settings for eth0:
Cannot get device settings: No such device
Cannot get wake-on-lan settings: No such device
Cannot get message level: No such device
Cannot get link status: No such device
No data available
With the patch installed.
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
[vm]# modprobe -r xen_netfront
[vm]# modprobe xen_netfront
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
Signed-off-by: Xiao Liang <xiliang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9939a46d90 ]
As for today STMMAC_ALIGN macro (which is used to align DMA stuff)
relies on L1 line length (L1_CACHE_BYTES).
This isn't correct in case of system with several cache levels
which might have L1 cache line length smaller than L2 line. This
can lead to sharing one cache line between DMA buffer and other
data, so we can lose this data while invalidate DMA buffer before
DMA transaction.
Fix that by using SMP_CACHE_BYTES instead of L1_CACHE_BYTES for
aligning.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b0753408aa ]
mdio_mux_iproc_probe() uses platform_set_drvdata() to store md pointer
in device, whereas mdio_mux_iproc_remove() restores md pointer by
dev_get_platdata(&pdev->dev). This leads to wrong resources release.
The patch replaces getter to platform_get_drvdata.
Fixes: 98bc865a1e ("net: mdio-mux: Add MDIO mux driver for iProc SoCs")
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 136f55f660 ]
As long the bh tasklet isn't scheduled once, no packet from the rx path
will be handled. Since the tx path also schedule the same tasklet
this situation only persits until the first packet transmission.
So fix this issue by scheduling the tasklet after link reset.
Link: https://github.com/raspberrypi/linux/issues/2617
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Suggested-by: Floris Bos <bos@je-eigen-domein.nl>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7f3fc7ddf7 ]
If we enable or disable xgbe flow-control by ethtool ,
it does't work.Because the parameter is not properly
assigned,so we need to adjust the assignment order
of the parameters.
Fixes: c1ce2f7736 ("amd-xgbe: Fix flow control setting logic")
Signed-off-by: tangpengpeng <tangpengpeng@higon.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 101f0cd4f2 ]
UBSAN triggers the following undefined behaviour warnings:
[...]
[ 13.236124] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:468:22
[ 13.240043] shift exponent 64 is too large for 64-bit type 'long long unsigned int'
[...]
[ 13.744769] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:373:4
[ 13.748694] shift exponent 64 is too large for 64-bit type 'long long unsigned int'
[...]
When splitting the address to high and low, GENMASK_ULL is used to generate
a bitmask with dma_addr_bits field from io_sq (in ena_com_prepare_tx and
ena_com_add_single_rx_desc).
The problem is that dma_addr_bits is not initialized with a proper value
(besides being cleared in ena_com_create_io_queue).
Assign dma_addr_bits the correct value that is stored in ena_dev when
initializing the SQ.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Gal Pressman <pressmangal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bb2289f90 upstream.
Implement adjust_link function that allows to overwrite default CPU port
setting using fixed-link device tree subnode.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eee1fe6476 upstream.
When a port is brought up/down do not enable/disable only the TXMAC
but the RXMAC as well. This is essential for the CPU port to work.
Fixes: 6b93fb4648 ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79a4ed4f0f upstream.
By default autonegotiation is enabled to configure MAC on all ports.
For the CPU port autonegotiation can not be used so we need to set
some sensible defaults manually.
This patch forces the default setting of the CPU port to 1000Mbps/full
duplex which is the chip maximum capability.
Also correct size of the bit field used to configure link speed.
Fixes: 6b93fb4648 ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4dc93fcf0b ]
On the RAH registers there are semantic differences on the meaning of
the "queue" parameter for traffic steering depending on the controller
model: there is the 82575 meaning, which "queue" means a RX Hardware
Queue, and the i350 meaning, where it is a reception pool.
The previous behaviour was having no effect for i210 based controllers
because the QSEL bit of the RAH register wasn't being set.
This patch separates the condition in discrete cases, so the different
handling is clearer.
Fixes: 83c21335c8 ("igb: improve MAC filter handling")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 38e62046d4 ]
This patch fixes the handling of the check when number of vports
are detected to be more than available TPQs. Current handling causes
an out of bounds access in hclge_map_tqp().
Fixes: 7df7dad633 ("net: hns3: Refactor the mapping of tqp to vport")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dac0490718 ]
Only non-NPAR PFs need to actively check and manage unsupported link
speeds. NPAR functions and VFs do not control the link speed and
should skip the unsupported speed detection logic, to avoid warning
messages from firmware rejecting the unsupported firmware calls.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9c4a121e82 ]
Add support for the BCM43364 chipset via an SDIO interface, as used in
e.g. the Murata 1FX module.
The BCM43364 uses the same firmware as the BCM43430 (which is already
included), the only difference is the omission of Bluetooth.
However, the SDIO_ID for the BCM43364 is 02D0:A9A4, giving it a MODALIAS
of sdio:c00v02D0dA9A4, which doesn't get recognised and hence doesn't
load the brcmfmac module. Adding the 'A9A4' ID in the appropriate place
triggers the brcmfmac driver to load, and then correctly use the
firmware file 'brcmfmac43430-sdio.bin'.
Signed-off-by: Sean Lanigan <sean@lano.id.au>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit daab3349ad ]
We are not releasing the link GPIO descriptor with gpiod_put() which results in
subsequent probing to get -EBUSY when calling fwnode_get_named_gpiod(). Fix this
by doing the release in phylink_destroy().
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c79756cb5f ]
In commit bbc4e7d273 ("i40e: fix race condition with PTP_TX_IN_PROGRESS
bits") we modified the code which handles Tx timestamps so that we would
clear the progress bit as soon as possible.
A later commit 0bc0706b46 ("i40e: check for Tx timestamp timeouts during
watchdog") introduced similar code for detecting and handling cleanup of
a blocked Tx timestamp. This code did not use the same pattern for cleaning
up the skb.
Update this code to wait to free the skb until after the bit lock is
free, by first setting the ptp_tx_skb to NULL and clearing the lock.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c6213eb1ae ]
This fixes klockworks warnings: Pointer 'dev' returned from call to
function 'bus_find_device' at line 179 may be NULL and will be dereferenced
at line 181.
cpsw-phy-sel.c:179: 'dev' is assigned the return value from function 'bus_find_device'.
bus.c:342: 'bus_find_device' explicitly returns a NULL value.
cpsw-phy-sel.c:181: 'dev' is dereferenced by passing argument 1 to function 'dev_get_drvdata'.
device.h:1024: 'dev' is passed to function 'dev_get_drvdata'.
device.h:1026: 'dev' is explicitly dereferenced.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[nsekhar@ti.com: add an error message, fix return path]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6e7d0ba1e5 ]
Set hw->mac.perm_addr in ixgbevf_set_mac() in order to avoid losing the
custom MAC on reset. This can happen in the following case:
>ip link set $vf address $mac
>ethtool -r $vf
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 13562d1f5e ]
This patch fixes the missing initialization of the client list node
in the hnae3_register_client() function.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 30bfce0b63 ]
Correct snr/nr/rssi data index to avoid possible buffer underflow.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 64cf81675a ]
Add support for the four-port variant of the Qualcomm QCA833x switch.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 699e2302c2 ]
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9c790f2d23 ]
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2a3169a54b ]
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 667ddac574 ]
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ea3986ad2 ]
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f183687e3 ]
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ba8df0c52 ]
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 45faf6e096 ]
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 01fb2994a9 ]
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7d0b130cbb ]
RX Buffer Descriptor contains a VALID bit which indicates if the BD
is valid and has some data. This field is set by HNS3 hardware to
intimate the driver of some valid data present in the BD. nd should
be reset by the driver when BD is being used again. In the existing
code this bit was not being (re-)initialized properly and hence was
causing problems.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6e91d48371 ]
the wl pointer can be null In case only wlcore_sdio is probed while
no WiLink module is successfully probed, as in the case of mounting a
wl12xx module while using a device tree file configured with wl18xx
related settings.
In this case the system was crashing in wl1271_suspend() as platform
device data is not set.
Make sure wl the pointer is valid before using it.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b817047ae7 ]
Race condition is observed during rmmod of mwifiex_usb:
1. The rmmod thread will call mwifiex_usb_disconnect(), download
SHUTDOWN command and do wait_event_interruptible_timeout(),
waiting for response.
2. The main thread will handle the response and will do a
wake_up_interruptible(), unblocking rmmod thread.
3. On getting unblocked, rmmod thread will make rx_cmd.urb = NULL in
mwifiex_usb_free().
4. The main thread will try to resubmit rx_cmd.urb in
mwifiex_usb_submit_rx_urb(), which is NULL.
To fix, wait for main thread to complete before calling
mwifiex_usb_free().
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shawn Guo