In MMC driver, two variables: boot_config and part_config are used to
keep eCSD(179) PARTITION_CONFIG. The part_config is not updated when
set new boot_config, which causes the eCSD(179) is overwritten by
any following partition switching, so the new boot_config is lost.
Signed-off-by: Ye.Li <B37916@freescale.com>
(cherry picked from commit e66d21ade29855299ce048c97830a4bb79373761)
- Configure boot partition
Expose the interfaces that used to enable the configurations
of the boot mode of the eMMC cards.
usage how-to and examples:
Enable the boot partition 1 boot enabled.
"echo 8 > /sys/devices/soc0/soc.1/2100000.aips-bus/
219c000.usdhc/mmc_host/mmc2/mmc2\:0001/boot_config"
In order to make sure that the re-read the ext-csd of card
can be completed successfully, add the method to wait for
the finish of the busy state.
- setup boot_info message output
Output bit means of important esd_csd register
Read esd_csd info each time when cat boot_info
becasue user may change config affect esd_csd
value.
- Boot partition access howto:
About the details, please refer to the guidance of
Documentation/mmc/mmc-dev-parts.txt
To enable write access to /dev/mmcblkXbootY, disable the forced
read-only access with:
echo 0 > /sys/block/mmcblkXbootY/force_ro
To re-enable read-only access:
echo 1 > /sys/block/mmcblkXbootY/force_ro
NOTE:
- The definitions of the EXT_CSD_PART_CONFIG and EXT_CSD_BOOT_BUS_WIDTH
+------------------------------------------------------------+
| Bit7 | Bit6 | Bit5 Bit4 Bit3 | Bit2 Bit1 Bit0 |
|------|----------|-----------------------|------------------|
| X | BOOT_ACK | BOOT_PARTITION_ENABLE | PARTITION_ACCESS |
+------------------------------------------------------------+
Bit7: Reserved
Bit6: always set to vaule '1' when boot_part is enabled
Bit[5:3]:
0x0 : Device not boot enabled (default)
0x1 : Boot partition 1 enabled for boot
0x2 : Boot partition 2 enabled for boot
0x7 : User area enabled for boot
Bit[2:0]:
0x0 : No access to boot partition (default)
0x1 : R/W boot partition 1
0x2 : R/W boot partition 2
+--------------------------------------------------------------------+
| Bit7 Bit6 Bit5 | Bit4 Bit3 | Bit2 | Bit1 Bit0 |
|----------------|----------------------------------|----------------|
| X | BOOT_MODE | RESET_BOOT_BUS_WIDTH | BOOT_BUS_WIDTH |
+--------------------------------------------------------------------+
Bit [4:3] : BOOT_MODE (non-volatile)
0x0 : Use single data rate + backward compatible timings in boot
operation (default)
0x1 : Use single data rate + high speed timings in boot operation mode
0x2 : Use dual data rate in boot operation
0x3 : Reserved
Bit [2]: RESET_BOOT_BUS_WIDTH (non-volatile)
0x0 : Reset bus width to x1, single data rate and backward compatible
timings after boot operation (default)
0x1 : Retain boot bus width and boot mode after boot operation
Bit[1:0] : BOOT_BUS_WIDTH (non-volatile)
0x0 : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default)
0x1 : x4 (sdr/ddr) bus width in boot operation mode
0x2 : x8 (sdr/ddr) bus width in boot operation mode
0x3 : Reserved
- example of the boot_info:
boot_info:0x07;
ALT_BOOT_MODE:1 - Supports alternate boot method
DDR_BOOT_MODE:1 - Supports alternate dual data rate during boot
HS_BOOTMODE:1 - Supports high speed timing during boot
boot_size:2048KB
boot_partition:0x48;
BOOT_ACK:1 - Boot acknowledge sent during boot operation
BOOT_PARTITION-ENABLE: 1 - Boot partition 1 enabled
PARTITION_ACCESS:0 - No access to boot partition
boot_bus:0x00
BOOT_MODE:0 - Use single data rate + backward compatible timings
in boot operation
RESET_BOOT_BUS_WIDTH:0 - Reset bus width to x1, single data rate
and backwardcompatible timings after boot operation
BOOT_BUS_WIDTH:0 - x1 (sdr) or x4 (ddr) bus width in boot
operation mode
Signed-off-by: Richard Zhu <r65037@freescale.com>
Separate out I2C functionality into a module. This fixes several small
issues and simplifies the driver initialization.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add support for additional devices and register equivalent family devices
including the bq27010, bq27210, bq27500, bq27510, bq27520, bq27530,
bq27531, bq27541, bq27542, bq27546, bq27545, bq27441, bq27421, and the
bq27641.
To facilitate this process the register mapings have been moved to tables
and other small cleanups have been made.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
When initialized as a platform device the initializer must now specify
a device. An empty device name is no longer valid.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Rename functions that are used by multiple devices. New devices
have been added and the function names and driver name are no longer
general enough for the functionality they provide.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: GUAN Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
* tag 'rel_imx_4.1.15_1.2.0_ga': (56 commits)
MLK-12948 ARM: dts: imx7d-sdb: change the hardware reset gpio for mipi dsi
MLK-12946 media: pxp-v4l2: correct the 32 bpp pixel format passed to pxp
mmc: mmc: fix switch timeout issue caused by jiffies precision
mmc: core: fix __mmc_switch timeout caused by preempt
MLK-12934-2 mmc: sdhci-esdhc-imx: do not touch other bit when config DTOCV
MLK-12934-1 mmc: sdhci-esdhc-imx: correct the max timeout count
MLK-12944 fix makefile miss imx7d-12x12-lpddr3-arm2-pcie.dtb
MLK-12935 ARM: imx: switch system counter clock to 32K in suspend
MLK-12902: usdhc: Revert "MLK-11685-5 mmc: sdhci-esdhc-imx: no need busfreq for imx6qdl"
MLK-12899-2 video: mipi_dsi_samsung: add panel 'TFT3P5581' driver.
MLK-12899-1 ARM: dts: imx7d-sdb: add dts support for panel 'TFT3P5581'.
MLK-12901-3 video: mipi_dsi_samsung: alwasy use video mode to transfer data and cmds.
MLK-12901-2 video: mipi_dsi_samsung: add 10msec delay after all the pkt write operation.
MLK-12901-1 video: mipi_dsi_samsung: correct the hardware reset calling position.
MLK_12886-2 video: mxsfb: handle the assert gpio in driver to support deferred probe
MLK-12886-1 ARM: dts: imx7d-sdb: the assert gpio for lcdif should be active low
MLK-12898: ov5640 mipi: Add more delay to wait sensor stable
MLK-12880 arm: dts: imx7d: correct the PAD_GPIO1_IO01 pin ctrl setting
MLK-12876: mipi csi: Remove regulator enable code when driver probe
MLK-12860-4 usb: chipidea: imx: add HSIC support for imx7d
...
[ Upstream commit d7591f0c41 ]
The three variants use same copy&pasted code, condense this into a
helper and use that.
Make sure info.name is 0-terminated.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit ce683e5f9d ]
We're currently asserting that targetoff + targetsize <= nextoff.
Extend it to also check that targetoff is >= sizeof(xt_entry).
Since this is generic code, add an argument pointing to the start of the
match/target, we can then derive the base structure size from the delta.
We also need the e->elems pointer in a followup change to validate matches.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit fc1221b3a1 ]
32bit rulesets have different layout and alignment requirements, so once
more integrity checks get added to xt_check_entry_offsets it will reject
well-formed 32bit rulesets.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 7d35812c32 ]
Currently arp/ip and ip6tables each implement a short helper to check that
the target offset is large enough to hold one xt_entry_target struct and
that t->u.target_size fits within the current rule.
Unfortunately these checks are not sufficient.
To avoid adding new tests to all of ip/ip6/arptables move the current
checks into a helper, then extend this helper in followup patches.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 759c01142a ]
On no-so-small systems, it is possible for a single process to cause an
OOM condition by filling large pipes with data that are never read. A
typical process filling 4000 pipes with 1 MB of data will use 4 GB of
memory. On small systems it may be tricky to set the pipe max size to
prevent this from happening.
This patch makes it possible to enforce a per-user soft limit above
which new pipes will be limited to a single page, effectively limiting
them to 4 kB each, as well as a hard limit above which no new pipes may
be created for this user. This has the effect of protecting the system
against memory abuse without hurting other users, and still allowing
pipes to work correctly though with less data at once.
The limit are controlled by two new sysctls : pipe-user-pages-soft, and
pipe-user-pages-hard. Both may be disabled by setting them to zero. The
default soft limit allows the default number of FDs per process (1024)
to create pipes of the default size (64kB), thus reaching a limit of 64MB
before starting to create only smaller pipes. With 256 processes limited
to 1024 FDs each, this results in 1024*64kB + (256*1024 - 1024) * 4kB =
1084 MB of memory allocated for a user. The hard limit is disabled by
default to avoid breaking existing applications that make intensive use
of pipes (eg: for splicing).
Reported-by: socketpair@gmail.com
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Mitigates: CVE-2013-4312 (Linux 2.0+)
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 2ccccf5fb4 ]
When the bottom qdisc decides to, for example, drop some packet,
it calls qdisc_tree_decrease_qlen() to update the queue length
for all its ancestors, we need to update the backlog too to
keep the stats on root qdisc accurate.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 86a7996cc8 ]
Remove nearly duplicated code and prepare for the following patch.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit f719e3754e ]
Jiri Bohac is reporting for a problem where the attempt
to reschedule existing connection to another real server
needs proper redirect for the conntrack used by the IPVS
connection. For example, when IPVS connection is created
to NAT-ed real server we alter the reply direction of
conntrack. If we later decide to select different real
server we can not alter again the conntrack. And if we
expire the old connection, the new connection is left
without conntrack.
So, the only way to redirect both the IPVS connection and
the Netfilter's conntrack is to drop the SYN packet that
hits existing connection, to wait for the next jiffie
to expire the old connection and its conntrack and to rely
on client's retransmission to create new connection as
usually.
Jiri Bohac provided a fix that drops all SYNs on rescheduling,
I extended his patch to do such drops only for connections
that use conntrack. Here is the original report from Jiri Bohac:
Since commit dc7b3eb900 ("ipvs: Fix reuse connection if real server
is dead"), new connections to dead servers are redistributed
immediately to new servers. The old connection is expired using
ip_vs_conn_expire_now() which sets the connection timer to expire
immediately.
However, before the timer callback, ip_vs_conn_expire(), is run
to clean the connection's conntrack entry, the new redistributed
connection may already be established and its conntrack removed
instead.
Fix this by dropping the first packet of the new connection
instead, like we do when the destination server is not available.
The timer will have deleted the old conntrack entry long before
the first packet of the new connection is retransmitted.
Fixes: dc7b3eb900 ("ipvs: Fix reuse connection if real server is dead")
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit fe30937b65 ]
bond_get_stats() can be called from rtnetlink (with RTNL held)
or from /proc/net/dev seq handler (with RCU held)
The logic added in commit 5f0c5f73e5 ("bonding: make global bonding
stats more reliable") kind of assumed only one cpu could run there.
If multiple threads are reading /proc/net/dev, stats can be really
messed up after a while.
A second problem is that some fields are 32bit, so we need to properly
handle the wrap around problem.
Given that RTNL is not always held, we need to use
bond_for_each_slave_rcu().
Fixes: 5f0c5f73e5 ("bonding: make global bonding stats more reliable")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 2793a23aac ]
Netdevice parameter hard_header_len is variously interpreted both as
an upper and lower bound on link layer header length. The field is
used as upper bound when reserving room at allocation, as lower bound
when validating user input in PF_PACKET.
Clarify the definition to be maximum header length. For validation
of untrusted headers, add an optional validate member to header_ops.
Allow bypassing of validation by passing CAP_SYS_RAWIO, for instance
for deliberate testing of corrupt input. In this case, pad trailing
bytes, as some device drivers expect completely initialized headers.
See also http://comments.gmane.org/gmane.linux.network/401064
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 880621c260 ]
Commit 9c7077622d ("packet: make packet_snd fail on len smaller
than l2 header") added validation for the packet size in packet_snd.
This change enforces that every packet needs a header (with at least
hard_header_len bytes) plus a payload with at least one byte. Before
this change the payload was optional.
This fixes PPPoE connections which do not have a "Service" or
"Host-Uniq" configured (which is violating the spec, but is still
widely used in real-world setups). Those are currently failing with the
following message: "pppd: packet size is too short (24 <= 24)"
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 1837b2e2bc ]
The current reserved_tailroom calculation fails to take hlen and tlen into
account.
skb:
[__hlen__|__data____________|__tlen___|__extra__]
^ ^
head skb_end_offset
In this representation, hlen + data + tlen is the size passed to alloc_skb.
"extra" is the extra space made available in __alloc_skb because of
rounding up by kmalloc. We can reorder the representation like so:
[__hlen__|__data____________|__extra__|__tlen___]
^ ^
head skb_end_offset
The maximum space available for ip headers and payload without
fragmentation is min(mtu, data + extra). Therefore,
reserved_tailroom
= data + extra + tlen - min(mtu, data + extra)
= skb_end_offset - hlen - min(mtu, skb_end_offset - hlen - tlen)
= skb_tailroom - min(mtu, skb_tailroom - tlen) ; after skb_reserve(hlen)
Compare the second line to the current expression:
reserved_tailroom = skb_end_offset - min(mtu, skb_end_offset)
and we can see that hlen and tlen are not taken into account.
The min() in the third line can be expanded into:
if mtu < skb_tailroom - tlen:
reserved_tailroom = skb_tailroom - mtu
else:
reserved_tailroom = tlen
Depending on hlen, tlen, mtu and the number of multicast address records,
the current code may output skbs that have less tailroom than
dev->needed_tailroom or it may output more skbs than needed because not all
space available is used.
Fixes: 4c672e4b ("ipv6: mld: fix add_grhead skb_over_panic for devs with large MTUs")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit b9a1a74381 ]
ARM64 allmodconfig produces a bunch of warnings when building the
samsung ASoC code:
sound/soc/samsung/dmaengine.c: In function 'samsung_asoc_init_dma_data':
sound/soc/samsung/dmaengine.c:53:32: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
playback_data->filter_data = (void *)playback->channel;
sound/soc/samsung/dmaengine.c:60:31: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
capture_data->filter_data = (void *)capture->channel;
We could easily shut up the warning by adding an intermediate cast,
but there is a bigger underlying problem: The use of IORESOURCE_DMA
to pass data from platform code to device drivers is dubious to start
with, as what we really want is a pointer that can be passed into
a filter function.
Note that on s3c64xx, the pl08x DMA data is already a pointer, but
gets cast to resource_size_t so we can pass it as a resource, and it
then gets converted back to a pointer. In contrast, the data we pass
for s3c24xx is an index into a device specific table, and we artificially
convert that into a pointer for the filter function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 7e8b3dfef1 ]
The HOSTPC extension registers found in some EHCI implementations form
a variable-length array, with one element for each port. Therefore
the hostpc field in struct ehci_regs should be declared as a
zero-length array, not a single-element array.
This fixes a problem reported by UBSAN.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Tested-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 3194ed4979 ]
HD-audio driver uses regmap cache bypass feature for reading a raw
value without the cache. But this is racy since both the cached and
the uncached reads may occur concurrently. The former is done via the
normal control API access while the latter comes from the proc file
read.
Even though the regmap itself has the protection against the
concurrent accesses, the flag set/reset is done without the
protection, so it may lead to inconsistent state of bypass flag that
doesn't match with the current read and occasionally result in a
kernel WARNING like:
WARNING: CPU: 3 PID: 2731 at drivers/base/regmap/regcache.c:499 regcache_cache_only+0x78/0x93
One way to work around such a problem is to wrap with a mutex. But in
this case, the solution is simpler: for the uncached read, we just
skip the regmap and directly calls its accessor. The verb execution
there is protected by itself, so basically it's safe to call
individually.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116171
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=eoKr
-----END PGP SIGNATURE-----
Merge tag 'v4.1.26' into 4.1-1.0.x-imx
Linux 4.1.26
* tag 'v4.1.26': (234 commits)
Linux 4.1.26
hpfs: implement the show_options method
affs: fix remount failure when there are no options changed
hpfs: fix remount failure when there are no options changed
Input: pwm-beeper - fix - scheduling while atomic
dma-debug: avoid spinlock recursion when disabling dma-debug
UBI: Fix static volume checks when Fastmap is used
xen/events: Don't move disabled irqs
xen/x86: actually allocate legacy interrupts on PV guests
wait/ptrace: assume __WALL if the child is traced
sunrpc: fix stripping of padded MIC tokens
mmc: sdhci-acpi: Remove MMC_CAP_BUS_WIDTH_TEST for Intel controllers
mmc: longer timeout for long read time quirk
drm/i915: Don't leave old junk in ilk active watermarks on readout
PM / sleep: Handle failures in device_suspend_late() consistently
Input: uinput - handle compat ioctl for UI_SET_PHYS
kvm: arm64: Fix EC field in inject_abt64
ALSA: hda - Fix headphone noise on Dell XPS 13 9360
ALSA: hda - Fix headphone mic input on a few Dell ALC293 machines
cifs: Create dedicated keyring for spnego operations
...
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
[ Upstream commit dd5f1b049d ]
The INTID mask is wrong, and is made a signed value, which has
nteresting effects in the KVM emulation. Let's sanitize it.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit ca9eb49aa9 ]
The generic copy_siginfo() is currently defined in
asm-generic/siginfo.h, after including uapi/asm-generic/siginfo.h which
defines the generic struct siginfo. However this makes it awkward for an
architecture to use it if it has to define its own struct siginfo (e.g.
MIPS and potentially IA64), since it means that asm-generic/siginfo.h
can only be included after defining the arch-specific siginfo, which may
be problematic if the arch-specific definition needs definitions from
uapi/asm-generic/siginfo.h.
It is possible to work around this by first including
uapi/asm-generic/siginfo.h to get the constants before defining the
arch-specific siginfo, and include asm-generic/siginfo.h after. However
uapi headers can't be included by other uapi headers, so that first
include has to be in an ifdef __kernel__, with the non __kernel__ case
including the non-UAPI header instead.
Instead of that mess, move the generic copy_siginfo() definition into
linux/signal.h, which allows an arch-specific uapi/asm/siginfo.h to
include asm-generic/siginfo.h and define the arch-specific siginfo, and
for the generic copy_siginfo() to see that arch-specific definition.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Petr Malat <oss@malat.biz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Christopher Ferris <cferris@google.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # 4.0-
Patchwork: https://patchwork.linux-mips.org/patch/12478/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit bb208f144c ]
As described in 'can: m_can: tag current CAN FD controllers as non-ISO'
(6cfda7fbeb) it is possible to define fixed configuration options by
setting the according bit in 'ctrlmode' and clear it in 'ctrlmode_supported'.
This leads to the incovenience that the fixed configuration bits can not be
passed by netlink even when they have the correct values (e.g. non-ISO, FD).
This patch fixes that issue and not only allows fixed set bit values to be set
again but now requires(!) to provide these fixed values at configuration time.
A valid CAN FD configuration consists of a nominal/arbitration bittiming, a
data bittiming and a control mode with CAN_CTRLMODE_FD set - which is now
enforced by a new can_validate() function. This fix additionally removed the
inconsistency that was prohibiting the support of 'CANFD-only' controller
drivers, like the RCar CAN FD.
For this reason a new helper can_set_static_ctrlmode() has been introduced to
provide a proper interface to handle static enabled CAN controller options.
Reported-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Reviewed-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Cc: <stable@vger.kernel.org> # >= 3.18
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 6fb650d43d ]
When a USB driver is bound to an interface (either through probing or
by claiming it) or is unbound from an interface, the USB core always
disables Link Power Management during the transition and then
re-enables it afterward. The reason is because the driver might want
to prevent hub-initiated link power transitions, in which case the HCD
would have to recalculate the various LPM parameters. This
recalculation takes place when LPM is re-enabled and the new
parameters are sent to the device and its parent hub.
However, if the driver does not want to prevent hub-initiated link
power transitions then none of this work is necessary. The parameters
don't need to be recalculated, and LPM doesn't need to be disabled and
re-enabled.
It turns out that disabling and enabling LPM can be time-consuming,
enough so that it interferes with user programs that want to claim and
release interfaces rapidly via usbfs. Since the usbfs kernel driver
doesn't set the disable_hub_initiated_lpm flag, we can speed things up
and get the user programs to work by leaving LPM alone whenever the
flag isn't set.
And while we're improving the way disable_hub_initiated_lpm gets used,
let's also fix its kerneldoc.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Matthew Giassa <matthew@giassa.net>
CC: Mathias Nyman <mathias.nyman@intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 0f40fbbcc3 ]
OpenSSH expects the (non-blocking) read() of pty master to return
EAGAIN only if it has received all of the slave-side output after
it has received SIGCHLD. This used to work on pre-3.12 kernels.
This fix effectively forces non-blocking read() and poll() to
block for parallel i/o to complete for all ttys. It also unwinds
these changes:
1) f8747d4a46
tty: Fix pty master read() after slave closes
2) 52bce7f8d4
pty, n_tty: Simplify input processing on final close
3) 1a48632ffe
pty: Fix input race when closing
Inspired by analysis and patch from Marc Aurele La France <tsi@tuyoix.net>
Reported-by: Volth <openssh@volth.com>
Reported-by: Marc Aurele La France <tsi@tuyoix.net>
BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=52
BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=2492
Signed-off-by: Brian Bloniarz <brian.bloniarz@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit feb26ac31a ]
The XHCI controller presents two USB buses to the system - one for USB2
and one for USB3. The hub init code (hub_port_init) is reentrant but
only locks one bus per thread, leading to a race condition failure when
two threads attempt to simultaneously initialise a USB2 and USB3 device:
[ 8.034843] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[ 13.183701] usb 3-3: device descriptor read/all, error -110
On a test system this failure occurred on 6% of all boots.
The call traces at the point of failure are:
Call Trace:
[<ffffffff81b9bab7>] schedule+0x37/0x90
[<ffffffff817da7cd>] usb_kill_urb+0x8d/0xd0
[<ffffffff8111e5e0>] ? wake_up_atomic_t+0x30/0x30
[<ffffffff817dafbe>] usb_start_wait_urb+0xbe/0x150
[<ffffffff817db10c>] usb_control_msg+0xbc/0xf0
[<ffffffff817d07de>] hub_port_init+0x51e/0xb70
[<ffffffff817d4697>] hub_event+0x817/0x1570
[<ffffffff810f3e6f>] process_one_work+0x1ff/0x620
[<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620
[<ffffffff810f4684>] worker_thread+0x64/0x4b0
[<ffffffff810f4620>] ? rescuer_thread+0x390/0x390
[<ffffffff810fa7f5>] kthread+0x105/0x120
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
[<ffffffff81ba183f>] ret_from_fork+0x3f/0x70
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
Call Trace:
[<ffffffff817fd36d>] xhci_setup_device+0x53d/0xa40
[<ffffffff817fd87e>] xhci_address_device+0xe/0x10
[<ffffffff817d047f>] hub_port_init+0x1bf/0xb70
[<ffffffff811247ed>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff817d4697>] hub_event+0x817/0x1570
[<ffffffff810f3e6f>] process_one_work+0x1ff/0x620
[<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620
[<ffffffff810f4684>] worker_thread+0x64/0x4b0
[<ffffffff810f4620>] ? rescuer_thread+0x390/0x390
[<ffffffff810fa7f5>] kthread+0x105/0x120
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
[<ffffffff81ba183f>] ret_from_fork+0x3f/0x70
[<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200
Which results from the two call chains:
hub_port_init
usb_get_device_descriptor
usb_get_descriptor
usb_control_msg
usb_internal_control_msg
usb_start_wait_urb
usb_submit_urb / wait_for_completion_timeout / usb_kill_urb
hub_port_init
hub_set_address
xhci_address_device
xhci_setup_device
Mathias Nyman explains the current behaviour violates the XHCI spec:
hub_port_reset() will end up moving the corresponding xhci device slot
to default state.
As hub_port_reset() is called several times in hub_port_init() it
sounds reasonable that we could end up with two threads having their
xhci device slots in default state at the same time, which according to
xhci 4.5.3 specs still is a big no no:
"Note: Software shall not transition more than one Device Slot to the
Default State at a time"
So both threads fail at their next task after this.
One fails to read the descriptor, and the other fails addressing the
device.
Fix this in hub_port_init by locking the USB controller (instead of an
individual bus) to prevent simultaneous initialisation of both buses.
Fixes: 638139eb95 ("usb: hub: allow to process more usb hub events in parallel")
Link: https://lkml.org/lkml/2016/2/8/312
Link: https://lkml.org/lkml/2016/2/4/748
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The pxp require two clocks to enable when it works, and
they are 'ipg' and 'axi' clocks. Besides, the two clocks
share the same CCGR to control clock gating.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
[ Upstream commit 689de1d6ca ]
This is a fairly minimal fixup to the horribly bad behavior of hash_64()
with certain input patterns.
In particular, because the multiplicative value used for the 64-bit hash
was intentionally bit-sparse (so that the multiply could be done with
shifts and adds on architectures without hardware multipliers), some
bits did not get spread out very much. In particular, certain fairly
common bit ranges in the input (roughly bits 12-20: commonly with the
most information in them when you hash things like byte offsets in files
or memory that have block factors that mean that the low bits are often
zero) would not necessarily show up much in the result.
There's a bigger patch-series brewing to fix up things more completely,
but this is the fairly minimal fix for the 64-bit hashing problem. It
simply picks a much better constant multiplier, spreading the bits out a
lot better.
NOTE! For 32-bit architectures, the bad old hash_64() remains the same
for now, since 64-bit multiplies are expensive. The bigger hashing
cleanup will replace the 32-bit case with something better.
The new constants were picked by George Spelvin who wrote that bigger
cleanup series. I just picked out the constants and part of the comment
from that series.
Cc: stable@vger.kernel.org
Cc: George Spelvin <linux@horizon.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit f4c18e6f7b ]
The race condition addressed in commit add05cecef ("mm: soft-offline:
don't free target page in successful page migration") was not closed
completely, because that can happen not only for soft-offline, but also
for hard-offline. Consider that a slab page is about to be freed into
buddy pool, and then an uncorrected memory error hits the page just
after entering __free_one_page(), then VM_BUG_ON_PAGE(page->flags &
PAGE_FLAGS_CHECK_AT_PREP) is triggered, despite the fact that it's not
necessary because the data on the affected page is not consumed.
To solve it, this patch drops __PG_HWPOISON from page flag checks at
allocation/free time. I think it's justified because __PG_HWPOISON
flags is defined to prevent the page from being reused, and setting it
outside the page's alloc-free cycle is a designed behavior (not a bug.)
For recent months, I was annoyed about BUG_ON when soft-offlined page
remains on lru cache list for a while, which is avoided by calling
put_page() instead of putback_lru_page() in page migration's success
path. This means that this patch reverts a major change from commit
add05cecef about the new refcounting rule of soft-offlined pages, so
"reuse window" revives. This will be closed by a subsequent patch.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dean Nelson <dnelson@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Hugh Dickins <hughd@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit e6bd18f57a ]
The drivers/infiniband stack uses write() as a replacement for
bi-directional ioctl(). This is not safe. There are ways to
trigger write calls that result in the return structure that
is normally written to user space being shunted off to user
specified kernel memory instead.
For the immediate repair, detect and deny suspicious accesses to
the write API.
For long term, update the user space libraries and the kernel API
to something that doesn't present the same security vulnerabilities
(likely a structured ioctl() interface).
The impacted uAPI interfaces are generally only available if
hardware from drivers/infiniband is installed in the system.
Reported-by: Jann Horn <jann@thejh.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[ Expanded check to all known write() entry points ]
Cc: stable@vger.kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 3020ca7118 ]
The VSync polarity was negative instead of positive for the 4k CEA formats.
I probably copy-and-pasted these from the DMT 4k format, which does have a
negative VSync polarity.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Martin Bugge <marbugge@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.1 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 3b67262307 ]
The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff
instead of 0x1f) thus reading entire register as buck9's voltage. This
effectively caused regulator core to interpret values as higher voltages
than they were and then to set real voltage much lower than intended.
The buck9 provides power to other regulators, including LDO13
and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower
voltage caused SD card detection errors on Odroid XU3/XU4:
mmc1: card never left busy state
mmc1: error -110 whilst initialising SD card
During driver probe the regulator core was checking whether initial
voltage matches the constraints. With incorrect vsel_mask of 0xff and
default value of 0x50, the core interpreted this as 5 V which is outside
of constraints (3-3.775 V). Then the regulator core was adjusting the
voltage to match the constraints. With incorrect vsel_mask this new
voltage mapped to a vere low voltage in the driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 2531c8cf56 ]
s390 has a constant hugepage size, by setting HPAGE_SHIFT we also change
e.g. the pageblock_order, which should be independent in respect to
hugepage support.
With this patch every architecture is free to define how to check
for hugepage support.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>