gsm_cleanup_mux() is called in the line discipline close path which
is called at tty_release() time. At this stage the tty is no longer
operational enough to send any frames. Sending close frames is
therefore not possible and waiting for their answers always times
out.
This patch removes sending close messages and waiting for their answers
from the tty_release path.
This patch makes explicit what previously implicitly had been the case
already: We are not able to tell the modem that we are about to close
the multiplexer on our side. This means the modem will stay in
multiplexer mode and re-establishing the multiplexer later fails. The
only way for userspace to work around this is to manually send a close
frame in N_TTY mode after closing the mux.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sccnxp driver doesn't get the correct uart clock rate, if CONFIG_HAVE_CLOCK
is disabled. Correct usage of clk API to make it work with/without it.
Fixes: 90efa75f7a (serial: sccnxp: Using CLK API for getting UART clock)
Suggested-by: Russell King - ARM Linux <linux@armlinux.org.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Historically the N_TTY driver could never fail but this has become broken over
time. Rather than trying to rewrite half the ldisc layer to fix the breakage
introduce a second level of fallback with an N_NULL ldisc which cannot fail,
and thus restore the guarantees required by the ldisc layer.
We still try and fail to N_TTY first. It's much more useful to find yourself
back in your old ldisc (first attempt) or in N_TTY (second attempt), and while
I'm not aware of any code out there that makes those assumptions it's good to
drive(r) defensively.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver calls ioremap() in the probe function but doesn't call
iounmap() in the remove function correspondingly. Do so now.
Follow commit 5c9d6abed9 ("serial: altera_jtaguart: adding iounmap()")
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e61c38d85b ("serial: imx: setup DCEDTE early and ensure DCD and
RI irqs to be off") has a flaw: While UCR3 and UFCR were modified using
read-modify-write before it switched to write register values
independent of the previous state. That's a good idea in principle (and
that's why I did it) but needs more care.
This patch reinstates read-modify-write for UFCR and for UCR3 ensures
that RXDMUXSEL and ADNIMP are set for post imx1.
Fixes: e61c38d85b ("serial: imx: setup DCEDTE early and ensure DCD and RI irqs to be off")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Mika Penttilä <mika.penttila@nextfour.com>
Tested-by: Mika Penttilä <mika.penttila@nextfour.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AUX/mini-UART in the BCM2835 family of procesors is a cut-down
8250 clone. In particular it is lacking support for the following
features: CSTOPB PARENB PARODD CMSPAR CS5 CS6
Add a new capability (UART_CAP_MINI) that exposes the restrictions to
the user of the termios API by turning off the unsupported features in
the request.
N.B. It is almost possible to automatically discover the missing
features by reading back the LCR register, but the CSIZE bits don't
cooperate (contrary to the documentation, both bits are significant,
but CS5 and CS6 are mapped to CS7) and the code is much longer.
See: https://github.com/raspberrypi/linux/issues/1561
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit below changed a function call from
dma_request_slave_channel_compat() to dma_request_slave_channel(), but
forgot to update the printed failure message.
Fixes: 219fb0c143 ("serial: sh-sci: Remove the platform data dma slave rx/tx channel IDs")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly added meson_uart_enable_tx_engine function is only called
from the console setup, not the runtime uart, which has an open-coded
version of the same register access. This produces a harmless warning
when the console code is disabled:
drivers/tty/serial/meson_uart.c:127:13: error: 'meson_uart_enable_tx_engine' defined but not used [-Werror=unused-function]
Let's move the function inside of the #ifdef to avoid the warning.
Fixes: ba50f1df13 ("serial: meson: remove unneeded variable assignment in meson_serial_port_write")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable serdev support by using the new device-registration helpers.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new interface for registering a serdev controller and clients, and
a helper function to deregister serdev devices (or a tty device) that
were previously registered using the new interface.
Once every driver currently using the tty_port_register_device() helpers
have been vetted and converted to use the new serdev registration
interface (at least for deregistration), we can move serdev registration
to the current helpers and get rid of the serdev-specific functions.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with commit 6fe729c4bd ("serdev: Add serdev_device_write
subroutine") the function serdev_device_write_buf cannot be used in
atomic context anymore (mutex_lock is sleeping). So restore the old
behavior.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 6fe729c4bd ("serdev: Add serdev_device_write subroutine")
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With serdev we might end up with serial ports that have no cdev exported
to userspace, as they are used as the bus interface to other devices. In
that case serial_match_port() won't be able to find a matching tty_dev.
Skip the irq wakeup enabling in that case, as serdev will make sure to
keep the port active, as long as there are devices depending on it.
Fixes: 8ee3fde047 (tty_port: register tty ports with serdev bus)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_insert_flip_string_fixed_flag() is racy against itself when called
from the ioctl(TCXONC, TCION/TCIOFF) path [1] and the flush_to_ldisc()
workqueue path [2].
The problem is that port->buf.tail->used is modified without consistent
locking; the ioctl path takes tty->atomic_write_lock, whereas the workqueue
path takes ldata->output_lock.
We cannot simply take ldata->output_lock, since that is specific to the
N_TTY line discipline.
It might seem natural to try to take port->buf.lock inside
tty_insert_flip_string_fixed_flag() and friends (where port->buf is
actually used/modified), but this creates problems for flush_to_ldisc()
which takes it before grabbing tty->ldisc_sem, o_tty->termios_rwsem,
and ldata->output_lock.
Therefore, the simplest solution for now seems to be to take
tty->atomic_write_lock inside tty_port_default_receive_buf(). This lock
is also used in the write path [3] with a consistent ordering.
[1]: Call Trace:
tty_insert_flip_string_fixed_flag
pty_write
tty_send_xchar // down_read(&o_tty->termios_rwsem)
// mutex_lock(&tty->atomic_write_lock)
n_tty_ioctl_helper
n_tty_ioctl
tty_ioctl // down_read(&tty->ldisc_sem)
do_vfs_ioctl
SyS_ioctl
[2]: Workqueue: events_unbound flush_to_ldisc
Call Trace:
tty_insert_flip_string_fixed_flag
pty_write
tty_put_char
__process_echoes
commit_echoes // mutex_lock(&ldata->output_lock)
n_tty_receive_buf_common
n_tty_receive_buf2
tty_ldisc_receive_buf // down_read(&o_tty->termios_rwsem)
tty_port_default_receive_buf // down_read(&tty->ldisc_sem)
flush_to_ldisc // mutex_lock(&port->buf.lock)
process_one_work
[3]: Call Trace:
tty_insert_flip_string_fixed_flag
pty_write
n_tty_write // mutex_lock(&ldata->output_lock)
// down_read(&tty->termios_rwsem)
do_tty_write (inline) // mutex_lock(&tty->atomic_write_lock)
tty_write // down_read(&tty->ldisc_sem)
__vfs_write
vfs_write
SyS_write
The bug can result in about a dozen different crashes depending on what
exactly gets corrupted when port->buf.tail->used points outside the
buffer.
The patch passes my LOCKDEP/PROVE_LOCKING testing but more testing is
always welcome.
Found using syzkaller.
Cc: <stable@vger.kernel.org>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Straighten out the initcall error handling to avoid deregistering a
never-registered tty driver (something which would lead to a
NULL-pointer dereference) in the most unlikely event that driver
registration fails (e.g. we've run out of major numbers).
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to deregister the SPI driver before releasing the tty driver
to avoid use-after-free in the SPI remove callback where the tty
devices are deregistered.
Fixes: 72d4724ea5 ("serial: ifx6x60: Add modem power off function in the platform reboot process")
Cc: stable <stable@vger.kernel.org> # 3.8
Cc: Jun Chen <jun.d.chen@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver does ioremap(port->mapbase, ALTERA_JTAGUART_SIZE),
but there is no any iounmap().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After migrating 8250_exar to MSI in 172c33cb61, we can get stuck
without further interrupts because of the special wake-up event these
chips send. They are only cleared by reading INT0. As we fail to do so
during startup and shutdown, we can leave the interrupt line asserted,
which is fatal with edge-triggered MSIs.
Add the required reading of INT0 to startup and shutdown. Also account
for the fact that a pending wake-up interrupt means we have to return 1
from exar_handle_irq. Drop the unneeded reading of INT1..3 along with
this - those never reset anything.
An alternative approach would have been disabling the wake-up interrupt.
Unfortunately, this feature (REGB[17] = 1) is not available on the
XR17D15X.
Fixes: 172c33cb61 ("serial: exar: Enable MSI support")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UARTn_FRAME_PARITY_ODD is 0x0300
UARTn_FRAME_PARITY_EVEN is 0x0200
So if the UART is configured for EVEN parity, it would be reported as ODD.
Fix it by correctly testing if the 2 bits are set.
Fixes: 3afbd89c96 ("serial/efm32: add new driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port client data must be set when registering the serdev controller
or client deregistration will fail (and the serdev devices are left
registered and allocated) if the port was never opened in between.
Make sure to clear the port client data on any probe errors to avoid a
use-after-free when the client is later deregistered unconditionally
(e.g. in a tty-port deregistration helper).
Also move port client operation initialisation to registration. Note
that the client ops must be restored on failed probe.
Fixes: bed35c6dfa ("serdev: add a tty port controller driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8ee3fde047.
The new serdev bus hooked into the tty layer in
tty_port_register_device() by registering a serdev controller instead of
a tty device whenever a serdev client is present, and by deregistering
the controller in the tty-port destructor. This is broken in several
ways:
Firstly, it leads to a NULL-pointer dereference whenever a tty driver
later deregisters its devices as no corresponding character device will
exist.
Secondly, far from every tty driver uses tty-port refcounting (e.g.
serial core) so the serdev devices might never be deregistered or
deallocated.
Thirdly, deregistering at tty-port destruction is too late as the
underlying device and structures may be long gone by then. A port is not
released before an open tty device is closed, something which a
registered serdev client can prevent from ever happening. A driver
callback while the device is gone typically also leads to crashes.
Many tty drivers even keep their ports around until the driver is
unloaded (e.g. serial core), something which even if a late callback
never happens, leads to leaks if a device is unbound from its driver and
is later rebound.
The right solution here is to add a new tty_port_unregister_device()
helper and to never call tty_device_unregister() whenever the port has
been claimed by serdev, but since this requires modifying just about
every tty driver (and multiple subsystems) it will need to be done
incrementally.
Reverting the offending patch is the first step in fixing the broken
lifetime assumptions. A follow-up patch will add a new pair of
tty-device registration helpers, which a vetted tty driver can use to
support serdev (initially serial core). When every tty driver uses the
serdev helpers (at least for deregistration), we can add serdev
registration to tty_port_register_device() again.
Note that this also fixes another issue with serdev, which currently
allocates and registers a serdev controller for every tty device
registered using tty_port_device_register() only to immediately
deregister and deallocate it when the corresponding OF node or serdev
child node is missing. This should be addressed before enabling serdev
for hot-pluggable buses.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fa01e2ca9f ("serial: 8250: Integrate Fintek into 8250_base")
modified the probing logic for PNP0501 devices, to remove a collision
between the generic 16550A driver and the Fintek driver, which reused
the same ACPI _HID.
The Fintek device probe is now incorporated into the common 8250 probe
path, and gets called for all discovered 16550A compatible devices,
including ones that are MMIO mapped rather than IO mapped. However,
the Fintek driver assumes the port base is a I/O address, and proceeds
to probe some arbitrary offsets above it.
This is generally a wrong thing to do, but on ARM systems (having no
native port I/O), this may result in faulting accesses of completely
unrelated MMIO regions in the PCI I/O space. Given that this is at
serial probe time, this results in hard to diagnose crashes at boot.
So let's restrict the Fintek probe to devices that we know are using
port I/O in the first place.
Fixes: fa01e2ca9f ("serial: 8250: Integrate Fintek into 8250_base")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ricardo Ribalda <ricardo.ribalda@gmail.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change interrupt description from driver name to tty name
(e.g. ttyAML0). If multiple serial ports are enabled this
allows to determine which interrupt belongs to which port
in /proc/interrupts.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flag UPF_IOREMAP is used by the 8250 subsystem only, it's not used
by the serial core. Therefore I don't see any benefit in using it
here.
In addition fix the order of calls in meson_uart_release_port.
Unmapping needs to be done first, reversing call order in
meson_uart_request_port.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Member mapsize of struct uart_port is meant to store the resource size.
By using it we can get rid of meson_uart_res_size().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
val is set in both branches of the if clause, therefore the two
removed lines are dead code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to set AML_UART_TX_EN in each call to
meson_serial_port_write. In addition to meson_uart_startup
set this flag in meson_serial_console_setup and
meson_serial_early_console_setup.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stop bit value as to be or'ed, so far this worked only just by chance
because AML_UART_STOP_BIN_1SB is 0.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AVR32 is gone. Now it's time to clean up the driver by removing
leftovers that was used by AVR32 related code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in printk message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the safe default for GPIOs with unknown external wiring.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
18a4208 introduced a change to reduce the RX DMA latency on the first reception
when the serial port was opened for reading. However it was claiming a hardirq
unsafe lock after a hardirq safe lock which is not allowed and causes lockdep
to complain verbosely.
This patch changes the code to always start RX DMA earlier, instead of
relying on the flags used to open the serial port removing the code that
was looking for the serial file flags.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of returning the requested baudrate, we better return the
actual one because it isn't always the same.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_register_driver call binds the driver to a specific device
node through tty_register_driver call. This should typically
happen during device probe call.
In a multiplatform scenario, it is possible that multiple serial
drivers are part of the kernel. Currently the driver registration fails
if multiple serial drivers with overlapping major/minor numbers are
included.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_register_driver call binds the driver to a specific device
node through tty_register_driver call. This should typically
happen during device probe call.
In a multiplatform scenario, it is possible that multiple serial
drivers are part of the kernel. Currently the driver registration fails
if multiple serial drivers with overlapping major/minor numbers are
included.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If DMA is enabled and used, a burst of old data may be seen on the
serial console during "poweroff" or "reboot". uart_flush_buffer()
clears the circular buffer, but sci_port.tx_dma_len is not reset.
This leads to a circular buffer overflow, dumping (UART_XMIT_SIZE -
sci_port.tx_dma_len) bytes.
To fix this, add a .flush_buffer() callback that resets
sci_port.tx_dma_len.
Inspired by commit 31ca2c63fd ("tty/serial: atmel: fix race
condition (TX+DMA)").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change adds a driver for the 16550-based Aspeed virtual UART
device. We use a similar process to the of_serial driver for device
probe, but expose some VUART-specific functions through sysfs too.
The VUART is two UART 'front ends' connected by their FIFO (no actual
serial line in between). One is on the BMC side (management controller)
and one is on the host CPU side.
This driver is for the BMC side. The sysfs files allow the BMC
userspace, which owns the system configuration policy, to specify at
what IO port and interrupt number the host side will appear to the host
on the Host <-> BMC LPC bus. It could be different on a different system
(though most of them use 3f8/4).
OpenPOWER host firmware doesn't like it when the host-side of the
VUART's FIFO is not drained. This driver only disables host TX discard
mode when the port is in use. We set the VUART enabled bit when we bind
to the device, and clear it on unbind.
We don't want to do this on open/release, as the host may be using this
bit to configure serial output modes, which is independent of whether
the devices has been opened by BMC userspace.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probing of THRE irq behaviour assumes the other end will be reading
bytes out of the buffer in order to probe the port at driver init. In
some cases the other end cannot be relied upon to read these bytes, so
provide a flag for them to skip this step.
Bit 19 was chosen as the flags are a int and the top bits are taken.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UPF_EXAR_EFR is set globally for each port enumerated by the driver.
Thus, no need to repeat this in individual ->setup() hook.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel always writes log messages to console via
serial8250_console_write()->serial8250_console_putchar() which directly
accesses UART_TX register _without_ using DMA.
But, if other processes like systemd using same UART port, then these
writes are handled by a different code flow using 8250_omap driver where
there is provision to use DMA.
It seems that it is possible that both DMA and CPU might simultaneously
put data to UART FIFO and lead to potential loss of data due to FIFO
overflow and weird data corruption. This happens when both kernel
console and userspace tries to write simultaneously to the same UART
port. Therefore, disable DMA on kernel console port to avoid potential
race between CPU and DMA.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
Here is the "big" TTY/Serial patch updates for 4.12-rc1
Not a lot of new things here, the normal number of serial driver updates
and additions, tiny bugs fixed, and some core files split up to make
future changes a bit easier for Nicolas's "tiny-tty" work.
All of these have been in linux-next for a while. There will be a merge
conflict with include/linux/serdev.h coming from the bluetooth tree
merge, which we knew about, as we wanted some of the serdev changes to
go in through that tree. I'll send the expected merge result as a
follow-on message.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iGwEABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWRA9rw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn8OwCXSoCtZMGl25ohu1osCL5G0UEMtgCg2Z9k7hDk
LpQTTN98hHn/VwM47ro=
=X8sk
-----END PGP SIGNATURE-----
Merge tag 'tty-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" TTY/Serial patch updates for 4.12-rc1
Not a lot of new things here, the normal number of serial driver
updates and additions, tiny bugs fixed, and some core files split up
to make future changes a bit easier for Nicolas's "tiny-tty" work.
All of these have been in linux-next for a while"
* tag 'tty-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (62 commits)
serial: small Makefile reordering
tty: split job control support into a file of its own
tty: move baudrate handling code to a file of its own
console: move console_init() out of tty_io.c
serial: 8250_early: Add earlycon support for Palmchip UART
tty: pl011: use "qdf2400_e44" as the earlycon name for QDF2400 E44
vt: make mouse selection of non-ASCII consistent
vt: set mouse selection word-chars to gpm's default
imx-serial: Reduce RX DMA startup latency when opening for reading
serial: omap: suspend device on probe errors
serial: omap: fix runtime-pm handling on unbind
tty: serial: omap: add UPF_BOOT_AUTOCONF flag for DT init
serial: samsung: Remove useless spinlock
serial: samsung: Add missing checks for dma_map_single failure
serial: samsung: Use right device for DMA-mapping calls
serial: imx: setup DCEDTE early and ensure DCD and RI irqs to be off
tty: fix comment typo s/repsonsible/responsible/
tty: amba-pl011: Fix spurious TX interrupts
serial: xuartps: Enable clocks in the pm disable case also
serial: core: Re-use struct uart_port {name} field
...
While examining output from trial builds with -Wformat-security enabled,
many strings were found that should be defined as "const", or as a char
array instead of char pointer. This makes some static analysis easier,
by producing fewer false positives.
As these are all trivial changes, it seemed best to put them all in a
single patch rather than chopping them up per maintainer.
Link: http://lkml.kernel.org/r/20170405214711.GA5711@beast
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Jes Sorensen <jes@trained-monkey.org> [runner.c]
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Antonio Quartulli <a@unstable.cc>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Kejian Yan <yankejian@huawei.com>
Cc: Daode Huang <huangdaode@hisilicon.com>
Cc: Qianqian Xie <xieqianqian@huawei.com>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Christian Gromm <christian.gromm@microchip.com>
Cc: Andrey Shvetsov <andrey.shvetsov@k2l.de>
Cc: Jason Litzinger <jlitzingerdev@gmail.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Fix sparse warnings in drivers/of/.
- Add more overlay unittests.
- Update dtc to v1.4.4-8-g756ffc4f52f6. This adds more checks on dts
files such as unit-address formatting and stricter character sets for
node and property names.
- Add a common DT modalias function.
- Move trivial-devices.txt up and out of i2c dir.
- ARM NVIC interrupt controller binding.
- Vendor prefixes for Sensirion, Dioo, Nordic, ROHM.
- Correct some binding file locations.
-----BEGIN PGP SIGNATURE-----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=ca1M
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- fix sparse warnings in drivers/of/
- add more overlay unittests
- update dtc to v1.4.4-8-g756ffc4f52f6. This adds more checks on dts
files such as unit-address formatting and stricter character sets for
node and property names
- add a common DT modalias function
- move trivial-devices.txt up and out of i2c dir
- ARM NVIC interrupt controller binding
- vendor prefixes for Sensirion, Dioo, Nordic, ROHM
- correct some binding file locations
* tag 'devicetree-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (24 commits)
of: fix sparse warnings in fdt, irq, reserved mem, and resolver code
of: fix sparse warning in of_pci_range_parser_one
of: fix sparse warnings in of_find_next_cache_node
of/unittest: Missing unlocks on error
of: fix uninitialized variable warning for overlay test
of: fix unittest build without CONFIG_OF_OVERLAY
of: Add unit tests for applying overlays
of: per-file dtc compiler flags
fpga: region: add missing DT documentation for config complete timeout
of: Add vendor prefix for ROHM Semiconductor
of: fix "/cpus" reference leak in of_numa_parse_cpu_nodes()
of: Add vendor prefix for Nordic Semiconductor
dt-bindings: arm,nvic: Binding for ARM NVIC interrupt controller on Cortex-M
dtc: update warning settings for new bus and node/property name checks
scripts/dtc: Update to upstream version v1.4.4-8-g756ffc4f52f6
scripts/dtc: automate getting dtc version and log in update script
of: Add function for generating a DT modalias with a newline
of: fix of_device_get_modalias returned length when truncating buffers
Documentation: devicetree: move trivial-devices out of I2C realm
dt-bindings: add vendor prefix for Dioo
..
Tetsuo has reported that sysrq triggered OOM killer will print a
misleading information when no tasks are selected:
sysrq: SysRq : Manual OOM execution
Out of memory: Kill process 4468 ((agetty)) score 0 or sacrifice child
Killed process 4468 ((agetty)) total-vm:43704kB, anon-rss:1760kB, file-rss:0kB, shmem-rss:0kB
sysrq: SysRq : Manual OOM execution
Out of memory: Kill process 4469 (systemd-cgroups) score 0 or sacrifice child
Killed process 4469 (systemd-cgroups) total-vm:10704kB, anon-rss:120kB, file-rss:0kB, shmem-rss:0kB
sysrq: SysRq : Manual OOM execution
sysrq: OOM request ignored because killer is disabled
sysrq: SysRq : Manual OOM execution
sysrq: OOM request ignored because killer is disabled
sysrq: SysRq : Manual OOM execution
sysrq: OOM request ignored because killer is disabled
The real reason is that there are no eligible tasks for the OOM killer
to select but since commit 7c5f64f844 ("mm: oom: deduplicate victim
selection code for memcg and global oom") the semantic of out_of_memory
has changed without updating moom_callback.
This patch updates moom_callback to tell that no task was eligible which
is the case for both oom killer disabled and no eligible tasks. In
order to help distinguish first case from the second add printk to both
oom_killer_{enable,disable}. This information is useful on its own
because it might help debugging potential memory allocation failures.
Fixes: 7c5f64f844 ("mm: oom: deduplicate victim selection code for memcg and global oom")
Link: http://lkml.kernel.org/r/20170404134705.6361-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sascha Hauer