This driver should compile on all platforms, activate it under compile
test. The Lantiq specific parts are under ifdef and should be removed
when Lantiq platform supports common clock framework.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver supports the Lantiq SSC SPI controller in master
mode. This controller is found on Intel (former Lantiq) SoCs like
the Danube, Falcon, xRX200, xRX300.
The hardware uses two hardware FIFOs one for received and one for
transferred bytes. When the driver writes data into the transmit FIFO
the complete word is taken from the FIFO into a shift register. The
data from this shift register is then written to the wire. This driver
uses the interrupts signaling the status of the FIFOs and not the shift
register. It is also possible to use the interrupts for the shift
register, but they will send a signal after every word. When using the
interrupts for the shift register we get a signal when the last word is
written into the shift register and not when it is written to the wire.
After all FIFOs are empty the driver busy waits till the hardware is
not busy any more and returns the transfer status.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Falcon spi accesses some ebu functions which are not exported and can
not be accessed when build as module. Make this module bool instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Thomas Langer <thomas.langer@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Broadcom BCM7XXX ARM and MIPS based SoCs share a similar hardware
block for SPI.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If NO_DMA=y:
ERROR: "bad_dma_ops" [drivers/spi/spi-fsl-dspi.ko] undefined!
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Marvell Armada 3700 SoC comprises an SPI Controller. This Controller
supports up to 4 SPI slave devices, with dedicated chip selects,supports
SPI mode 0/1/2 and 3, CPIO or Fifo mode with DMA transfers and different
SPI transfer mode (Single, Dual or Quad).
This commit adds basic driver support for FIFO mode. In this mode,
dedicated registers are used to store the instruction, the address, the
read mode and the data. Write and Read FIFO are used to store the
outcoming or incoming data. The data FIFOs are accessible via DMA or by
the CPU. Only the CPU is supported for now.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MVEBU chips (Armada XP, Armada 370 and others) are supported by this
driver. Mention this in the help text to make more obvious what is
already specified in the dependencies of this symbol.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds lpspi driver to support new i.MX products which use
lpspi instead of ecspi.
The lpspi can continue operating in stop mode when an appropriate
clock is available. It is also designed for low CPU overhead with
DMA offloading of FIFO register accesses.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After having removed all code dependencies we can make fsl-espi
completely independent of fsl-lib now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver only has runtime but no build time dependency with PLAT_SAMSUNG
|| ARCH_EXYNOS so it can be built for testing purposes if the COMPILE_TEST
option is enabled.
This is useful to have more build coverage and make sure that the driver
is not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Master SPI driver for Broadcom settop, iProc SoCs. The driver
is used for devices that use SPI protocol on BRCMSTB, NSP, NS2
SoCs. SoC platform driver call exported porbe(), remove()
and suspend/resume pm_ops implemented in this common driver.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Yendapally Reddy Dhananjaya Reddy
Signed-off-by: Mark Brown <broonie@kernel.org>
"spi_sh_msiof" is used on sh7723 and sh7724 only. As all of the above
select ARCH_SHMOBILE, restrict its driver dependencies from SUPERH to
ARCH_SHMOBILE.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ThunderX SPI driver using the shared part from the Octeon
driver. The main difference of the ThunderX driver is that it
is a PCI device so probing is different. The system clock settings
can be specified in device tree.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The J-Core "spi2" device is a PIO-based SPI master controller. It
differs from "bitbang" devices in that that it's clocked in hardware
rather than via soft clock modulation over gpio, and performs
byte-at-a-time transfers between the cpu and SPI controller.
This driver will be extended to support future versions of the J-Core
SPI controller with DMA transfers when they become available.
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function sg_split will be used by spi-omap2-mcspi to handle a SoC
workaround in the SPI driver. Therefore, select SG_SPLIT so this function
is available to the driver.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Even if DMA support is disabled code using DMA mapping APIs compiles fine,
but fails in linking.
-------
drivers/built-in.o: In function `ring_desc_ring_free':
spi-pic32-sqi.c:(.text+0x2cfbe0): undefined reference to `bad_dma_ops'
spi-pic32-sqi.c:(.text+0x2cfbe4): undefined reference to `bad_dma_ops'
drivers/built-in.o: In function `pic32_sqi_probe':
spi-pic32-sqi.c:(.text+0x2cfe48): undefined reference to `bad_dma_ops'
spi-pic32-sqi.c:(.text+0x2cfeb0): undefined reference to `bad_dma_ops'
spi-pic32-sqi.c:(.text+0x2cff38): undefined reference to `bad_dma_ops'
--------
Correct dependency by adding 'depends on HAS_DMA' in Kconfig.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The relaxed I/O accessors are available on all architectures now.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no build dependency for this driver, so enable COMPILE_TEST to get
better build coverage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI controller managed by the spi-orion is used on the new ARM64
Marvell Armada 7K/8K SoCs. In order to allow this driver to be built
for this platform, we allow it to be selected for ARCH_MVEBU=y
configurations.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver implements SPI master interface for Quad SPI
controller, specifically for accessing quad SPI flash.
It uses descriptor-based DMA transfer mode and supports
half-duplex communication for single, dual and quad SPI
transactions.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PIC32 SPI driver is capable of performing SPI transfers
using PIO or external DMA engine. GPIO controlled /CS support
is made default in the driver for correct operation of the
controller. This can be enabled by adding "cs-gpios" property
of the SPI node in board dts file.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Vulcan spi controller is compatible with netlogic,xlp832-spi.
- Add depends on ARCH_VULCAN to Kconfig to enable spi controller
driver for Broadcom Vulcan ARM64 SoCs.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ICP DAS LP-8841 contains a DS-1302 RTC. This driver provides an SPI
master which makes the RTC usable. The driver is not supposed to work
with anything else.
The driver uses the standard MicroWire half-duplex transfer timing.
Master output is set on low clock and sensed by the RTC on the rising
edge. Master input is set by the RTC on the trailing edge and is sensed
by the master on low clock.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency of SPI_BCM2835AUX on GPIOLIB if COMPILE_TEST is
enabled.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the AXI SPI Engine controller which is a FPGA
soft-peripheral which is used in some of Analog Devices' reference designs.
The AXI SPI Engine controller is part of the SPI Engine framework[1] and
allows memory mapped access to the SPI Engine control bus. This allows it
to be used as a general purpose software driven SPI controller. The SPI
Engine in addition offers some optional advanced acceleration and
offloading capabilities, which are not part of this patch though and will
be introduced separately.
At the core of the SPI Engine framework is a small sort of co-processor
that accepts a command stream and turns the commands into low-level SPI
transactions. Communication is done through three memory mapped FIFOs in
the register map of the AXI SPI Engine peripheral. One FIFO for the command
stream and one each for transmit and receive data.
The driver translates a spi_message in a command stream and writes it to
the peripheral which executes it asynchronously. This allows it to perform
very precise timings which are required for some SPI slave devices to
achieve maximum performance (e.g. analog-to-digital and digital-to-analog
converters). The execution flow is synchronized to the host system by a
special synchronize instruction which generates a interrupt.
[1] https://wiki.analog.com/resources/fpga/peripherals/spi_engine
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
After removal of legacy PXA DMA code by the commit 6356437e65
("spi: spi-pxa2xx: remove legacy PXA DMA bits") the
CONFIG_SPI_PXA2XX_DMA follows the CONFIG_SPI_PXA2XX and cannot be disabled
alone. Therefore remove this config symbol and dead definitions from the
spi-pxa2xx.h.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
adding the spi-loopback-test module to Kconfig and Makefile
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow the topcliff-pch driver to be built for MIPS platforms, in
preparation for use on the MIPS Boston board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LS1043a and LS2080A in the Layerscape family also support DSPI, make
DSPI selectable for these hardwares.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown