During the transition to sub-devices several years ago non-subdev drivers
had a ' at the end of their driver name to tell them apart from already
converted drivers. This check was a left-over from that time and can be
removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In vb2_buffer_done, it would be better the print the value of 'state'
(current state of buffer) than to print 'vb->state' which is always
VB2_BUF_STATE_ACTIVE.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
An earlier patch temporarily disabled regional motion detection. This patch
adds it back: the 'Motion Detection Enable' control is now a 'Motion Detection Mode'.
And to set/get the regional thresholds two new ioctls were added to get/set those
thresholds.
The BUF_FLAG constants were also updated to prevent clashing with existing buffer
flags.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
FMT_MPEG is for multiplexed streams, not elementary streams. The same is
true for the V4L2_CID_MPEG_VIDEO_ENCODING control.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a consequence the ioctl op has been replaced by unlocked_ioctl.
Since we are now using the core lock the locking scheme has been
simplified as well.
The main reason for converting this driver to vb2 was that the locking
scheme in v4l2.c was hopeless. It was easier to just convert the driver
then to try and salvage a threading and videobuf nightmare.
The videobuf2 framework is far, far superior compared to the old videobuf.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a consequence the ioctl op has been replaced by unlocked_ioctl.
Since we are now using the core lock the locking scheme has been
simplified as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All fields in solo_enc_fh do not belong there since they refer to global
properties. After moving all these fields to solo_enc_dev the solo_dev_fh
struct can be removed completely.
Note that this also kills the 'listener' feature of this driver. This
feature (where multiple filehandles can read the video) is illegal in the
V4L2 API. Do this in userspace: it's much more efficient to copy memory
than it is to DMA to every listener.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All fields in solo_dev_fh do not belong there since they refer to global
properties. After moving all these fields to solo_dev the solo_dev_fh
struct can be removed completely.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- try_fmt should never return -EBUSY.
- invalid pix->field values were not mapped to a valid value.
- the priv field of struct v4l2_pix_format wasn't zeroed.
- the try_fmt error code was not checked in set_fmt.
- enum_framesizes/intervals is valid for both MJPEG and MPEG pixel formats.
- enum_frameintervals didn't check width and height and reported the
wrong range.
- s_parm didn't set readbuffers.
- don't fail on invalid colorspace, just replace with the valid colorspace.
- bytesperline should be 0 for compressed formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note that the MOTION_THRESHOLD functionality has been temporarily reduced:
only the global threshold can be set, not the per-block. This will be
addressed in a later patch: controls are not the proper way to do this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Setup correct bus_info, let the v4l2 core set the version and add device_caps
support.
Also update the module version to 3.0.0 since this is a major upgrade.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Synced to commit e9815ac5503ae60cfbf6ff8037035de8f62e2846 from
branch next in git repository https://github.com/bluecherrydvr/solo6x10.git
Only removed some code under #if LINUX_VERSION_CODE < some-kernel-version,
renamed the driver back to solo6x10 from solo6x10-edge, removed the
unnecessary compat.h header and kept the slab.h includes.
Otherwise the code is identical.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ismael Luceno <ismael.luceno@corp.bluecherry.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
lirc_sir uses the CONFIG_SA1100_BITSY Kconfig macro. But its Kconfig
symbol was removed in v2.4.13. So remove dead code associated with it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Case: In AdLink MPG24 there is bt878 exists (it captures one frame of all video
inputs), Video Signal for it one transmits through tw2804 chip, so we can't
control ADC (shut on/off) on tw2804, as some another can use bttv capture way.
Signed-off-by: Volokh Konstantin <volokh84@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For NUL terminated string, need always set '\0' in the end.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
version.h header inclusion is not necessary as detected by
versioncheck.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using two separate tables to setup the registers for 50 or 60 hz is
better than the non-const table that is filled in at runtime.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The go7007 driver would continue during probe if no firmware could be
loaded. Without firmware the probe() should return an error, so do that.
Also move the registration of devices to the end of the probe() sequence:
once devices appear the full driver functionality should be available.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Include the patch required to add support for the go7007 to saa7134.
To be applied once the driver is moved out of staging.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only thing missing after this to make the Sensoray model 614 board work is
to hook it up to the saa7134 driver, but that will have to wait until this
driver goes out of staging.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
[hans.verkuil@cisco.com: updated to make it merge correctly]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
version.h header inclusion is not necessary as detected by
versioncheck.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update the brighness range depending on the selected input. Useful for
testing control range events.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A patchset applied earlier changed v4l2_tuner struct parameter at
vidioc_s_tuner to const. Do this change at sony_btf_mpx_s_tuner(),
in order to remove this warning:
drivers/media/i2c/sony-btf-mpx.c:335:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/media/i2c/sony-btf-mpx.c:335:2: warning: (near initialization for 'sony_btf_mpx_tuner_ops.s_tuner') [enabled by default]
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This API is now obsolete and can be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This API is no longer used by any driver and so can be removed from the
documentation.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These ioctls are no longer used by any drivers, so remove them.
[mchehab@redhat.com: Fix merge conflict]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These ops are no longer used, so it's time to remove them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's no longer used, so it can now be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Taken from the 0.9.8-5 version of the out-of-tree wis-go7007 driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Taken from the 0.9.8-5 version of the out-of-tree wis-go7007 driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The firmware is always the same, so drop it from the board configs. Also make
the board configs const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Actually it's called "Group of VOP" start code in MPEG4 terminology.
Taken from the 0.9.8-5 version of the out-of-tree wis-go7007 driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
But now as a proper standard MPEG control.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
