fix bug in phy_init loop that was ignoring BMCR reset bit, akin to smsc95xx's d946092000
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx needs MII_ACCESS_BUSY to be set to correctly trigger mdio I/O. Note smsc75xx is different from smsc95xx in this regard.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the same issue as reported on smsc95xx, where the
usb device is connected with no ethernet cable plugged-in.
Without this patch sysfs reports the cable as present
flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1
while it's not:
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the cwnd reduction is done, ssthresh may be infinite
if TCP enters CWR via ECN or F-RTO. If cwnd is not undone, i.e.,
undo_marker is set, tcp_complete_cwr() falsely set cwnd to the
infinite ssthresh value. The correct operation is to keep cwnd
intact because it has been updated in ECN or F-RTO.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the helper function from filter.c for negative offsets is exported,
it can be used it in the jit to handle negative offsets.
First modify the asm load helper functions to handle:
- know positive offsets
- know negative offsets
- any offset
then the compiler can be modified to explicitly use these helper
when appropriate.
This fixes the case of a negative X register and allows to lift
the restriction that bpf programs with negative offsets can't
be jited.
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jan Seiffert <kaffeemonster@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current checking always succeeded. We have to check the first
character of the string to check that it's empty, thus, skipping
the timeout path.
This fixes the use of the CT target without the timeout option.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Change order of init so netns init is ready
when register ioctl and netlink.
Ver2
Whitespace fixes and __init added.
Reported-by: "Ryan O'Hara" <rohara@redhat.com>
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
ip_vs_create_timeout_table() can return NULL
All functions protocol init_netns is affected of this patch.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Avoid crash when registering shedulers after
the IPVS core initialization for netns fails. Do this by
checking for present core (net->ipvs).
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Eric Dumazet pointed out to me that the drop_monitor protocol has some holes in
its smp protections. Specifically, its possible to replace data->skb while its
being written. This patch corrects that by making data->skb an rcu protected
variable. That will prevent it from being overwritten while a tracepoint is
modifying it.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet pointed out this warning in the drop_monitor protocol to me:
[ 38.352571] BUG: sleeping function called from invalid context at kernel/mutex.c:85
[ 38.352576] in_atomic(): 1, irqs_disabled(): 0, pid: 4415, name: dropwatch
[ 38.352580] Pid: 4415, comm: dropwatch Not tainted 3.4.0-rc2+ #71
[ 38.352582] Call Trace:
[ 38.352592] [<ffffffff8153aaf0>] ? trace_napi_poll_hit+0xd0/0xd0
[ 38.352599] [<ffffffff81063f2a>] __might_sleep+0xca/0xf0
[ 38.352606] [<ffffffff81655b16>] mutex_lock+0x26/0x50
[ 38.352610] [<ffffffff8153aaf0>] ? trace_napi_poll_hit+0xd0/0xd0
[ 38.352616] [<ffffffff810b72d9>] tracepoint_probe_register+0x29/0x90
[ 38.352621] [<ffffffff8153a585>] set_all_monitor_traces+0x105/0x170
[ 38.352625] [<ffffffff8153a8ca>] net_dm_cmd_trace+0x2a/0x40
[ 38.352630] [<ffffffff8154a81a>] genl_rcv_msg+0x21a/0x2b0
[ 38.352636] [<ffffffff810f8029>] ? zone_statistics+0x99/0xc0
[ 38.352640] [<ffffffff8154a600>] ? genl_rcv+0x30/0x30
[ 38.352645] [<ffffffff8154a059>] netlink_rcv_skb+0xa9/0xd0
[ 38.352649] [<ffffffff8154a5f0>] genl_rcv+0x20/0x30
[ 38.352653] [<ffffffff81549a7e>] netlink_unicast+0x1ae/0x1f0
[ 38.352658] [<ffffffff81549d76>] netlink_sendmsg+0x2b6/0x310
[ 38.352663] [<ffffffff8150824f>] sock_sendmsg+0x10f/0x130
[ 38.352668] [<ffffffff8150abe0>] ? move_addr_to_kernel+0x60/0xb0
[ 38.352673] [<ffffffff81515f04>] ? verify_iovec+0x64/0xe0
[ 38.352677] [<ffffffff81509c46>] __sys_sendmsg+0x386/0x390
[ 38.352682] [<ffffffff810ffaf9>] ? handle_mm_fault+0x139/0x210
[ 38.352687] [<ffffffff8165b5bc>] ? do_page_fault+0x1ec/0x4f0
[ 38.352693] [<ffffffff8106ba4d>] ? set_next_entity+0x9d/0xb0
[ 38.352699] [<ffffffff81310b49>] ? tty_ldisc_deref+0x9/0x10
[ 38.352703] [<ffffffff8106d363>] ? pick_next_task_fair+0x63/0x140
[ 38.352708] [<ffffffff8150b8d4>] sys_sendmsg+0x44/0x80
[ 38.352713] [<ffffffff8165f8e2>] system_call_fastpath+0x16/0x1b
It stems from holding a spinlock (trace_state_lock) while attempting to register
or unregister tracepoint hooks, making in_atomic() true in this context, leading
to the warning when the tracepoint calls might_sleep() while its taking a mutex.
Since we only use the trace_state_lock to prevent trace protocol state races, as
well as hardware stat list updates on an rcu write side, we can just convert the
spinlock to a mutex to avoid this problem.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up a reference to jiffies in tcp_rcv_rtt_measure() that should
instead reference tcp_time_stamp. Since the result of the subtraction
is passed into a function taking u32, this should not change any
behavior (and indeed the generated assembly does not change on
x86_64). However, it seems worth cleaning this up for consistency and
clarity (and perhaps to avoid bugs if this is copied and pasted
somewhere else).
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch sysfs reports the cable as present
flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1
while it's not:
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Tested on my Beagle XM.
v2: added mantainer to the list of recipient
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dl2k driver's rio_ioctl call has a few issues:
- No permissions checking
- Implements SIOCGMIIREG and SIOCGMIIREG using the SIOCDEVPRIVATE numbers
- Has a few ioctls that may have been used for debugging at one point
but have no place in the kernel proper.
This patch removes all but the MII ioctls, renumbers them to use the
standard ones, and adds the proper permission check for SIOCSMIIREG.
We can also get rid of the dl2k-specific struct mii_data in favor of
the generic struct mii_ioctl_data.
Since we have the phyid on hand, we can add the SIOCGMIIPHY ioctl too.
Most of the MII code for the driver could probably be converted to use
the generic MII library but I don't have a device to test the results.
Reported-by: Stephan Mueller <stephan.mueller@atsec.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing spin_lock_init() for frames list lock.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean all the pending fragments and relative timers if 6lowpan link
is going to be deleted.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nescesary mlme callbacks to satisfy "iz list" request from user space.
Due to 6lowpan device doesn't have its own phy, mlme implemented as a pipe
to a real phy to which 6lowpan is attached.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a4910b7444 has broken promiscuous
mode, which is never set. port->promisc just reflects the last setting
of PROMISCUOUS mode to avoid doing an extra hypercall when it's already
set.
However, since it may fail because of hypervisor permissions, we should
still respect the multicast settings and not simply exit after setting
promiscuous mode.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a bug in the mask of regtype parameter for registering a
multicast filter. It was ignoring the scope bit, which was wrongly being
used for all filters. The SCOPE_ALL value adds a filter that allows all
multicast packets and ignores the MAC parameter, just what allmulticast
needs. The normals filters, however, should not use SCOPE_ALL.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure net->ipvs is reset on netns cleanup or failed
initialization. It is needed for IPVS applications to know that
IPVS core is not loaded in netns.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Avoid crash when registering ip_vs_ftp after
the IPVS core initialization for netns fails. Do this by
checking for present core (net->ipvs).
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
When we use netlink to monitor queue information for udp socket,
idiag_rqueue and idiag_wqueue of inet_diag_msg are returned with 0.
Keep consistent with netstat, just return back allocated rmem/wmem size.
Signed-off-by: Shan Wei <davidshan@tencent.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RSS is enabled, interrupt vector 0 does not receive any rx traffic.
The rx producer index fields for vector 0's status block should be
considered reserved in this case. This patch changes the code to
respect these reserved fields, which avoids a kernel panic when these
fields take on non-zero values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes this beauty into a statement that actually has an effect on amd64.
Tested-by: Per Jessen <per@opensuse.org>
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 14e405461e (2.6.39)
("Add __ip_vs_control_{init,cleanup}_sysctl()")
introduced regression due to wrong __net_init for
__ip_vs_control_cleanup_sysctl. This leads to crash when
the ip_vs module is unloaded.
Fix it by changing __net_init to __net_exit for
the function that is already renamed to ip_vs_control_net_cleanup_sysctl.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Based on the original patch from Ying Cai <ycai@google.com>
This change ensures that the itr/itr_setting adjustment logic is used,
even for the default/compiled-in value.
Context:
When we changed the default InterruptThrottleRate value from default
(3 = dynamic mode) to 8000 for example, only adapter->itr_setting
(which controls interrupt coalescing mode) was set to 8000, but
adapter->itr (which controls the value set in NIC register) was not
updated accordingly. So from ethtool, it seemed the interrupt
throttling is enabled at 8000 intr/s, but the NIC actually was
running in dynamic mode which has lower CPU efficiency especially
when throughput is not high.
CC: Ying Cai <ycai@google.com>
CC: David Decotigny <david.decotigny@google.com>
Signed-off-by: Jeff Kirsher <jeffrey.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Following logs where seen on Systems with multiple NICs,
while using MSI interrupts as shown below:
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0d.0: lan0_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: wan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: lan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.warn kernel: 0000:40:0e.0: wan4_0: MSI interrupt
test failed, using legacy interrupt.
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0e.0: wan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0e.0: lan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: wan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: lan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: wan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: lan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0e.0: lan4_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: wan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: lan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
This patch fixes this problem by increasing the msleep from 50 to 100.
Signed-off-by: Prasanna S Panchamukhi <ppanchamukhi@riverbed.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.
Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer devices have 20 (5000 series) or 30 (6000 series)
hardware queues, rather than the 16 that 4965 had. This
was added to the driver a long time ago, but improperly:
the queue registers for the higher queues aren't just
continuations of the registers for the first 16 queues,
they are in other places. Therefore, the hardware would
lock up when trying to activate queue 16 or above and
the device would have to be restarted.
Thanks goes to Emmanuel who identified this and told me
how the queue programming should be done.
Note that we don't use queues 20 and higher today and
doing so needs more work than this.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asix.c USB Ethernet driver avoids ending a tx transfer with a zero-
length packet by appending a four-byte padding to transfers whose length
is a multiple of maxpacket. However, the hard-coded 512 byte maxpacket
length is valid for high-speed USB only; full-speed USB uses 64 byte
packets.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY connect attempts fail if no PHY id is specified in the emac platform
data and another mdio bus has been registered before 'davinci_mdio' bus. In
this case when configuring the interface, there will be an attempt to
connect to already attached PHY on the previously registered mdio bus:
net eth1: PHY already attached
net eth1: could not connect to phy smsc911x-0:01
IP-Config: Failed to open eth1
IP-Config: Device `eth1' not found
Fix this by modifying match_first_device() to match first PHY device
on 'davinci_mdio' bus.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we receive an interrupt too early before we set up ports in the probe
function, there won't be any port ready to handle it.
Only registering the irq after the ports are setup fixes the problem,
and works fine without losing any interrupts.
This causes crashes in some situations:
[c000000f7ff7fd60] d000000008e223f0 .ehea_neq_tasklet+0x78/0x148 [ehea]
[c000000f7ff7fe00] c0000000000b6cac .tasklet_hi_action+0xdc/0x210
[c000000f7ff7fea0] c0000000000b7cc8 .__do_softirq+0x178/0x300
[c000000f7ff7ff90] c000000000022694 .call_do_softirq+0x14/0x24
[c000000f68ee7900] c000000000010e04 .do_softirq+0xec/0x110
[c000000f68ee79a0] c0000000000b789c .irq_exit+0xac/0xe0
[c000000f68ee7a20] c0000000000110bc .do_IRQ+0x114/0x2a8
[c000000f68ee7ae0] c00000000000553c hardware_interrupt_entry+0x18/0x1c
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous blkt defaults for OSA Express 4 cards produced inadequate
performance for streaming workloads. The present patch will apply a
set of more appropriate defaults.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There exist qeth sysfs blkt attributes to change the default blkt
values. But blkt changes are reset during online setting due to a 2nd
invocation of qeth_determine_capabilites(). This patch makes sure
blkt default values are configured during 1st run of
qeth_determine_capabilities() only. Thus blkt changes are kept
during online setting.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Reported-by: Horst Hartmann <horst.hartmann@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make smsc95xx recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1488 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Inspired by same fix on cdc_eem 78fb72f793.
Tested on ARM/Beagle.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: set fake_rtable's dst to NULL to avoid kernel Oops
when bridge is deleted before tap/vif device's delete, kernel may
encounter an oops because of NULL reference to fake_rtable's dst.
Set fake_rtable's dst to NULL before sending packets out can solve
this problem.
v4 reformat, change br_drop_fake_rtable(skb) to {}
v3 enrich commit header
v2 introducing new flag DST_FAKE_RTABLE to dst_entry struct.
[ Use "do { } while (0)" for nop br_drop_fake_rtable()
implementation -DaveM ]
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Peter Huang <peter.huangpeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull build system failure fix from Michal Marek:
"This fixes build failure with newer gcc that adds some internal
symbols that end in "__mod_*_device_table", but are not actually the
tables themselves."
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Fix modpost failures in fedora 17
2 are tagged for -stable, one being for a fairly serious bug
that can corrupt metadata and make it hard to recovery an array.
The other is for a more recent regression since 3.3
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=8UG6
-----END PGP SIGNATURE-----
Merge tag 'md-3.4-fixes' of git://neil.brown.name/md
Pull a few more md bug fixes from NeilBrown:
"2 are tagged for -stable, one being for a fairly serious bug that can
corrupt metadata and make it hard to recovery an array. The other is
for a more recent regression since 3.3"
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
md: fix possible corruption of array metadata on shutdown.
md: don't call ->add_disk unless there is good reason.
DM RAID: Use safe version of rdev_for_each
This includes one short patch fixing the behavior of
the QUECVT flag, which the gfs2 folks are waiting on.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=KDNZ
-----END PGP SIGNATURE-----
Merge tag 'dlm-fixes-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm
Pull dlm fixes from David Teigland:
"This includes one short patch fixing the behavior of the QUECVT flag,
which the gfs2 folks are waiting on."
* tag 'dlm-fixes-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
dlm: fix QUECVT when convert queue is empty
Mel reports a BUG_ON(slot == NULL) in radix_tree_tag_set() on s390
3.0.13: called from __set_page_dirty_nobuffers() when page_remove_rmap()
tries to transfer dirty flag from s390 storage key to struct page and
radix_tree.
That would be because of reclaim's shrink_page_list() calling
add_to_swap() on this page at the same time: first PageSwapCache is set
(causing page_mapping(page) to appear as &swapper_space), then
page->private set, then tree_lock taken, then page inserted into
radix_tree - so there's an interval before taking the lock when the
radix_tree slot is empty.
We could fix this by moving __add_to_swap_cache()'s spin_lock_irq up
before the SetPageSwapCache. But a better fix is simply to do what's
five years overdue: Ken Chen introduced __set_page_dirty_no_writeback()
(if !PageDirty TestSetPageDirty) for tmpfs to skip all the radix_tree
overhead, and swap is just the same - it ignores the radix_tree tag, and
does not participate in dirty page accounting, so should be using
__set_page_dirty_no_writeback() too.
s390 testing now confirms that this does indeed fix the problem.
Reported-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ken Chen <kenchen@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit c744a65c1e
md: don't set md arrays to readonly on shutdown.
removed the possibility of a 'BUG' when data is written to an array
that has just been switched to read-only, but also introduced the
possibility that the array metadata could be corrupted.
If, when md_notify_reboot gets the mddev lock, the array is
in a state where it is assembled but hasn't been started (as can
happen if the personality module is not available, or in other unusual
situations), then incorrect metadata will be written out making it
impossible to re-assemble the array.
So only call __md_stop_writes() if the array has actually been
activated.
This patch is needed for any stable kernel which has had the above
commit applied.
Cc: stable@vger.kernel.org
Reported-by: Christoph Nelles <evilazrael@evilazrael.de>
Signed-off-by: NeilBrown <neilb@suse.de>
