[ Upstream commit 0e254963b6 ]
Most register accesses in the altera driver honor port->regshift by
using altera_uart_writel(). There are a few accesses however that were
missed when the driver was converted to use port->regshift and some
others were added later in commit 4d9d7d896d ("serial: altera_uart:
add earlycon support").
Fixes: 2780ad42f5 ("tty: serial: altera_uart: Use port->regshift to store bus shift")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e9fe53910 ]
Currently, data in RX FIFO is read based on UART_LSR register state even
if RDI and RLSI interrupts are disabled in UART_IER register.
This is because when IRQ handler is called due to TX FIFO empty event,
RX FIFO is serviced based on UART_LSR register status instead of
UART_IIR status. This defeats the purpose of disabling UART RX
FIFO interrupts during throttling(see, omap_8250_throttle()) as IRQ
handler continues to drain UART RX FIFO resulting in overflow of buffer
at tty layer.
Fix this by making sure that driver drains UART RX FIFO only when
UART_IIR_RDI is set along with UART_LSR_BI or UART_LSR_DR bits.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f9f5786987 ]
The arc_uart_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_ARC_NR_PORTS), so this can even be triggered using a
legitimate DTB.
Fixes: ea28fd56fc ("serial/arc-uart: switch to devicetree based probing")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ffab87fdec ]
The lpuart_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: c9e2e946fb ("tty: serial: add Freescale lpuart driver support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5673444821 ]
The imx_ports[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: ff05967a07 ("serial/imx: add of_alias_get_id() reference back")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd345a31bf ]
The auart_port[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: 1ea6607d4c ("serial: mxs-auart: Allow device tree probing")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 49ee23b718 ]
The s3c24xx_serial_ports[] array is indexed using a value derived from
the "serialN" alias in DT, or from an incrementing probe index, which
may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_SAMSUNG_UARTS), so this can even be triggered using
a legitimate DTB or legitimate board code.
Fixes: 13a9f6c64f ("serial: samsung: Consider DT alias when probing ports")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 090fa4b0dc ]
The sci_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_SH_SCI_NR_UARTS), so this can even be triggered using a
legitimate DTB.
Fixes: 97ed9790c5 ("serial: sh-sci: Remove unused platform data capabilities field")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e7d75e18d0 ]
The cdns_uart_port[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: 928e926349 ("tty: xuartps: Initialize ports according to aliases")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 67300abdbe ]
Currently an out of range dev->nr is detected by just reporting the
issue and later on an out-of-bounds read on array card occurs because
of this. Fix this by checking the upper range of dev->nr with the size
of array card (removes the hard coded size), move this check earlier
and also exit with the error -ENOSYS to avoid the later out-of-bounds
array read.
Detected by CoverityScan, CID#711191 ("Out-of-bounds-read")
Fixes: commit 02b20b0b4c ("V4L/DVB (12730): Add conexant cx25821 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: %ld -> %zd]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 65243386f4 ]
The vivid driver has two custom controls that change the behavior of RDS.
Depending on the control setting the V4L2_CAP_READWRITE capability is toggled.
However, after an earlier commit the capability was no longer set correctly.
This is now fixed.
Fixes: 9765a32cd8 ("vivid: set device_caps in video_device")
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d13a0139d7 ]
Fixes vb2_vmalloc_get_userptr() to ioremap correct area.
Since the current code does ioremap the page address, if the offset > 0,
it does not do ioremap the last page and results in kernel panic.
This fixes to pass the size + offset to ioremap so that ioremap
can map correct area. Also, this uses __pfn_to_phys() to get the physical
address of given PFN.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reported-by: Takao Orito <orito.takao@socionext.com>
Reported-by: Fumihiro ATSUMI <atsumi@infinitegra.co.jp>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9f564184e6 ]
The ADV748x handles interlaced media using V4L2_FIELD_ALTERNATE field
types. The correct specification for the height on the mbus is the
image height, in this instance, the field height.
The AFE component already correctly adjusts the height on the mbus, but
the HDMI component got left behind.
Adjust the mbus height to correctly describe the image height of the
fields when processing interlaced video for HDMI pipelines.
Fixes: 3e89586a64 ("media: i2c: adv748x: add adv748x driver")
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e3e4cb5e2 ]
Make sure we don't accept more inputs than the hardware can handle. This
is a temporary fix to avoid display stall, we need to instead allocate
the BRU or BRS to display pipelines dynamically based on the number of
planes they each use.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 94448e21cf ]
Both lgdt33606a_release and lgdt3306a_remove kfree state, but _release is
called first, then _remove operates on states members before kfree'ing it.
This can lead to random oops/GPF/etc on USB disconnect.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a398e04363 ]
While experimenting with older compiler versions, I ran
into a warning that no longer shows up on gcc-4.8 or newer:
drivers/media/platform/s3c-camif/camif-capture.c: In function '__camif_subdev_try_format':
drivers/media/platform/s3c-camif/camif-capture.c:1265:25: error: array subscript is below array bounds
This is an off-by-one bug, leading to an access before the start of the
array, while newer compilers silently assume this undefined behavior
cannot happen and leave the loop at index 0 if no other entry matches.
As Sylvester explains, we actually need to ensure that the
value is within the range, so this reworks the loop to be
easier to parse correctly, and an additional check to fall
back on the first format value for any unexpected input.
I found an existing gcc bug for it and added a reduced version
of the function there.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=69249#c3
Fixes: babde1c243 ("[media] V4L: Add driver for S3C24XX/S3C64XX SoC series camera interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ceade1d97 ]
Currently clk_freq is ignored entirely, because the cx235840 driver
configures the xtal at the chip defaults. This is an issue if a
board is produced with a non-default frequency crystal. If clk_freq
is not zero the cx25840 will attempt to use the setting provided,
or fall back to defaults otherwise.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 779c79d4b8 ]
Hauppauge produced a revision of ImpactVCBe using an 888,
with a 25MHz crystal, instead of using the default third
overtone 50Mhz crystal. This overrides that frequency so
that the cx25840 is properly configured. Without the proper
crystal setup the cx25840 cannot load the firmware or
decode video.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 06fe932307 ]
The device node obtained with of_graph_get_next_endpoint() should be
released by calling of_node_put(). But it was not released when
v4l2_fwnode_endpoint_parse() failed.
This change moves the of_node_put() call before the error check and
fixes the issue.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3dd6b560dc ]
As pointed by Dan, possible values for bits[3:0] of te Line Mode Registers
can range from 0x0 to 0xf, but the check logic allow values ranging
from 0x0 to 0xe.
As static arrays are initialized with zero, using a value without
an explicit initializer at the array won't cause any harm.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a145f64c61 ]
Returning -EINVAL when an ioctl is not implemented is a very
bad idea, as it is hard to distinguish from other error
contitions that an ioctl could lead. Replace it by its
right error code: -ENOTTY.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a8321e7887 ]
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
In this patch an erroneous P value for 74176002 output frequency is also
corrected.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ac051eeab ]
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ab0447845c ]
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cdb68fbd4e ]
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7e4db0c283 ]
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 179db533c0 ]
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4bf59902b5 ]
The MMC sample and drv clock for rockchip platforms are derived from
the bus clock output to the MMC/SDIO card. So it should never happens
that the clk rate is zero given it should inherits the clock rate from
its parent. If something goes wrong and makes the clock rate to be zero,
the calculation would be wrong but may still make the mmc tuning process
work luckily. However it makes people harder to debug when the following
data transfer is unstable.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c35b518f9b ]
Turns out latest upstream U-Boot does not configure/enable pll_u which
leaves it at some default rate of 500 kHz:
root@apalis-t30:~# cat /sys/kernel/debug/clk/clk_summary | grep pll_u
pll_u 3 3 0 500000 0
Of course this won't quite work leading to the following messages:
[ 6.559593] usb 2-1: new full-speed USB device number 2 using tegra-
ehci
[ 11.759173] usb 2-1: device descriptor read/64, error -110
[ 27.119453] usb 2-1: device descriptor read/64, error -110
[ 27.389217] usb 2-1: new full-speed USB device number 3 using tegra-
ehci
[ 32.559454] usb 2-1: device descriptor read/64, error -110
[ 47.929777] usb 2-1: device descriptor read/64, error -110
[ 48.049658] usb usb2-port1: attempt power cycle
[ 48.759475] usb 2-1: new full-speed USB device number 4 using tegra-
ehci
[ 59.349457] usb 2-1: device not accepting address 4, error -110
[ 59.509449] usb 2-1: new full-speed USB device number 5 using tegra-
ehci
[ 70.069457] usb 2-1: device not accepting address 5, error -110
[ 70.079721] usb usb2-port1: unable to enumerate USB device
Fix this by actually allowing the rate also being set from within
the Linux kernel.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df934cbcbf ]
The symbol is in the __initconst section but not marked init, which
caused a warning when building with LTO.
This makes it 'const' as was obviously intended.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c80dfd9bf5 ("clk: hisilicon: add CRG driver for Hi3516CV300 SoC")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f9c63e8de ]
It's found that the clock phase output from clk_summary is
wrong compared to the actual phase reading from the register.
cat /sys/kernel/debug/clk/clk_summary | grep sdio_sample
sdio_sample 0 1 0 50000000 0 -22
It exposes an issue that clk core, clk_core_get_phase, always
returns the cached core->phase which should be either updated
by calling clk_set_phase or directly from the first place the
clk was registered.
When registering the clk, the core->phase geting from ->get_phase()
may return negative value indicating error. This is quite common
since the clk's phase may be highly related to its parent chain,
but it was temporarily orphan when registered, since its parent
chains hadn't be ready at that time, so the clk drivers decide to
return error in this case. However, if no clk_set_phase is called or
maybe the ->set_phase() isn't even implemented, the core->phase would
never be updated. This is wrong, and we should try to update it when
all its parent chains are settled down, like the way of updating clock
rate for that. But it's not deserved to complicate the code now and
just update it anyway when calling clk_core_get_phase, which would be
much simple and enough.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4b0556a441 ]
commit c420c1e4db22 ("clk: rockchip: Prevent calculating mmc phase
if clock rate is zero") catches one gremlin again for clk-rk3228.c
that the parent of SDMMC phase clock should be sclk_sdmmc0, but not
sclk_sdmmc. However, the naming of the sdmmc clocks varies in the
manual with the card clock having the 0 while the hclk is named
without appended 0. So standardize one one format to prevent
confusion, as there also is only one (non-sdio) mmc controller on
the soc.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 647d04f8e0 ]
If the RCLK mux clock configuration is specified in DT and no set_sysclk()
callback is used in the sound card driver the sclk_srcrate field will remain
set to 0, leading to an incorrect PSR divider setting.
To fix this the frequency value is retrieved from the CLK_I2S_RCLK_SRC clock,
so the actual RCLK mux selection is taken into account.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bde8b3887a ]
This patch adds the change required to create the TLV data
for dapm widget kcontrols from topology. This also fixes the following
TLV read error shown in amixer while showing the card control contents.
"amixer: Control hw:1 element TLV read error: No such device or address"
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d22c337dc ]
In case of sample rates lower than 44100 currently there is too low MCLK
frequency set for the CODEC. Playback fails with following errors:
$ speaker-test -c2 -t sine -f 1500 -l2 -r 32000
Sine wave rate is 1500.0000Hz
Rate set to 32000Hz (requested 32000Hz)
Buffer size range from 128 to 131072
Period size range from 64 to 65536
Using max buffer size 131072
Periods = 4
Unable to set hw params for playback: Invalid argument
Setting of hwparams failed: Invalid argument
[ 497.883700] max98090 1-0010: Invalid master clock frequency
To fix this the I2S root clock's frequency is increased, depending
on sampling rate.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b1d0db067f ]
The driver does not select all the codec drivers that needs.
Fix it by selecting the analog and HDMI codecs.
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e558f8afa ]
The hcp->chmap_info must not be freed up in the hdmi_codec_remove()
function as it leads to kernel crash due ALSA core's
pcm_chmap_ctl_private_free() is trying to free it up again when the card
destroyed via snd_card_free.
Commit cd6111b262 ("ASoC: hdmi-codec: add channel mapping control")
should not have added the kfree(hcp->chmap_info); to the hdmi_codec_remove
function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 04673e38f5 ]
The driver controls when the hardware sends completions that communicate
consumption of elements from the WQ. This is done by setting a WQEC bit
on a WQE.
The current driver sets it on every Nth WQE posting. However, the driver
isn't clearing the bit if the WQE is reused. Thus, if the queue depth
isn't evenly divisible by N, with enough time, it can be set on every
element, creating a lot of overhead and risking CQ full conditions.
Correct by clearing the bit when not setting it on an Nth element.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 161df4f099 ]
During link bounce testing in a point-to-point topology, the host may
enter a soft lockup on the lpfc_worker thread:
Call Trace:
lpfc_work_done+0x1f3/0x1390 [lpfc]
lpfc_do_work+0x16f/0x180 [lpfc]
kthread+0xc7/0xe0
ret_from_fork+0x3f/0x70
The driver was simultaneously setting a combination of flags that caused
lpfc_do_work()to effectively spin between slow path work and new event
data, causing the lockup.
Ensure in the typical wq completions, that new event data flags are set
if the slow path flag is running. The slow path will eventually
reschedule the wq handling.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2289e9598d ]
The driver ignored checks on whether the link should be kept
administratively down after a link bounce. Correct the checks.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e75fba9c06 ]
This patch fixes the byte order of the SGPIO api and brings it back in
sync with ledmon v0.80 and above.
[mkp: added missing SoB and fixed whitespace]
Signed-off-by: Wilfried Weissmann <wilfried.weissmann@gmx.at>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1875ede02e ]
The SCSI PRE-FETCH (10 or 16) command is present both on hard disks
and some SSDs. It is useful when the address of the next block(s) to
be read is known but it is not following the LBA of the current READ
(so read-ahead won't help). It returns two "good" SCSI Status values.
If the requested blocks have fitted (or will most likely fit (when
the IMMED bit is set)) into the disk's cache, it returns CONDITION
MET. If it didn't (or will not) fit then it returns GOOD status.
The goal of this patch is to stop the SCSI subsystem treating the
CONDITION MET SCSI status as an error. The current state makes the
PRE-FETCH command effectively unusable via pass-throughs.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 89d0c80439 ]
iscsi tcp will first send out data, then calculate and send data
digest. If we don't have BDI_CAP_STABLE_WRITES, the page cache will be
written in spite of the on going writeback. Consequently, wrong digest
will be got and sent to target.
To fix this, set BDI_CAP_STABLE_WRITES when data digest is enabled
in iscsi_tcp .slave_configure callback.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Acked-by: Chris Leech <cleech@redhat.com>
Acked-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20bd1d026a ]
If the read-only flag is true on a SCSI disk, re-reading the partition
table sets the flag back to false.
To observe this bug, you can run:
1. blockdev --setro /dev/sda
2. blockdev --rereadpt /dev/sda
3. blockdev --getro /dev/sda
This commit reads the disk's old state and combines it with the device
disk-reported state rather than unconditionally marking it as RW.
Reported-by: Li Ning <lining916740672@icloud.com>
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 864449eea7 ]
The firmware event workqueue should not be marked as WQ_MEM_RECLAIM
as it's doesn't need to make forward progress under memory pressure.
In the current state it will result in a deadlock if the device had been
forcefully removed.
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1bc5ad3a6a ]
A system crashes when continuously removing/re-adding the storage
controller.
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 00c20cdc79 ]
When aacraid init fails with "AAC0: adapter self-test failed.", shutdown
leads to UBSAN warning and then oops:
[154316.118423] ================================================================================
[154316.118508] UBSAN: Undefined behaviour in drivers/scsi/scsi_lib.c:2328:27
[154316.118566] member access within null pointer of type 'struct Scsi_Host'
[154316.118631] CPU: 2 PID: 14530 Comm: reboot Tainted: G W 4.15.0-dirty #89
[154316.118701] Hardware name: Hewlett Packard HP NetServer/HP System Board, BIOS 4.06.46 PW 06/25/2003
[154316.118774] Call Trace:
[154316.118848] dump_stack+0x48/0x65
[154316.118916] ubsan_epilogue+0xe/0x40
[154316.118976] __ubsan_handle_type_mismatch+0xfb/0x180
[154316.119043] scsi_block_requests+0x20/0x30
[154316.119135] aac_shutdown+0x18/0x40 [aacraid]
[154316.119196] pci_device_shutdown+0x33/0x50
[154316.119269] device_shutdown+0x18a/0x390
[...]
[154316.123435] BUG: unable to handle kernel NULL pointer dereference at 000000f4
[154316.123515] IP: scsi_block_requests+0xa/0x30
This is because aac_shutdown() does
struct Scsi_Host *shost = pci_get_drvdata(dev);
scsi_block_requests(shost);
and that assumes shost has been assigned with pci_set_drvdata().
However, pci_set_drvdata(pdev, shost) is done in aac_probe_one() far
after bailing out with error from calling the init function
((*aac_drivers[index].init)(aac)), and when the init function fails, no
error is returned from aac_probe_one() so PCI layer assumes there is
driver attached, and tries to shut it down later.
Fix it by returning error from aac_probe_one() when card-specific init
function fails.
This fixes reboot on my HP NetRAID-4M with dead battery.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
