commit 9d2ee0a60b upstream.
On brcmnand controller v6.x and v7.x, the #WP pin is controlled through
the NAND_WP bit in CS_SELECT register.
The driver currently assumes that toggling the #WP pin is
instantaneously enabling/disabling write-protection, but it actually
takes some time to propagate the new state to the internal NAND chip
logic. This behavior is sometime causing data corruptions when an
erase/program operation is executed before write-protection has really
been disabled.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2de3ec4f1d upstream.
The BSC data buffers to send and receive data are each of size 32 bytes
or 8 bytes 'xfersz' depending on SoC. The problem observed for all the
combined message transfer was if length of data transfer was a multiple
of 'xfersz' a repeated START was being transmitted by BSC driver. Fixed
this by appropriately setting START/STOP conditions for such transfers.
Fixes: dd1aa2524b ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77c0d0cd10 upstream.
Our code was assigning number of channels to the index variable by
default. If firmware reported channel we didn't predict this would
result in using that initial index value and writing out of array. This
never happened so far (we got a complete list of supported channels) but
it means possible memory corruption so we should handle it anyway.
This patch simply detects unexpected channel and ignores it.
As we don't try to create new entry now, it's also safe to drop hw_value
and center_freq assignment. For known channels we have these set anyway.
I decided to fix this issue by assigning NULL or a target channel to the
channel variable. This was one of possible ways, I prefefred this one as
it also avoids using channel[index] over and over.
Fixes: 58de92d2f9 ("brcmfmac: use static superset of channels for wiphy bands")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b0ff9a007 upstream.
hns_roce_v1_cq_set_ci() calls roce_set_bit() on an uninitialized field,
which will then change only a few of its bits, causing a warning with
the latest gcc:
infiniband/hw/hns/hns_roce_hw_v1.c: In function 'hns_roce_v1_cq_set_ci':
infiniband/hw/hns/hns_roce_hw_v1.c:1854:23: error: 'doorbell[1]' is used uninitialized in this function [-Werror=uninitialized]
roce_set_bit(doorbell[1], ROCEE_DB_OTHERS_H_ROCEE_DB_OTH_HW_SYNS_S, 1);
The code is actually correct since we always set all bits of the
port_vlan field, but gcc correctly points out that the first
access does contain uninitialized data.
This initializes the field to zero first before setting the
individual bits.
Fixes: 9a4435375c ("IB/hns: Add driver files for hns RoCE driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c51f4ae84 upstream.
Arnd Bergmann reported a (false positive) objtool warning:
drivers/infiniband/sw/rxe/rxe_resp.o: warning: objtool: rxe_responder()+0xfe: sibling call from callable instruction with changed frame pointer
The issue is in find_switch_table(). It tries to find a switch
statement's jump table by walking backwards from an indirect jump
instruction, looking for a relocation to the .rodata section. In this
case it stopped walking prematurely: the first .rodata relocation it
encountered was for a variable (resp_state_name) instead of a jump
table, so it just assumed there wasn't a jump table.
The fix is to ignore any .rodata relocation which refers to an ELF
object symbol. This works because the jump tables are anonymous and
have no symbols associated with them.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 3732710ff6 ("objtool: Improve rare switch jump table pattern detection")
Link: http://lkml.kernel.org/r/20170302225723.3ndbsnl4hkqbne7a@treble
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67bcc2c5f1 upstream.
Currently we add the virtual cpufreq device unconditionally even when
the SCPI DVFS clock provider node is disabled. This will cause cpufreq
driver to throw errors when it gets initailised on boot/modprobe and
also when the CPUs are hot-plugged back in.
This patch fixes the issue by adding the virtual cpufreq device only if
the SCPI DVFS clock provider is available and registered.
Fixes: 9490f01e24 ("clk: scpi: add support for cpufreq virtual device")
Reported-by: Michał Zegan <webczat_200@poczta.onet.pl>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Michał Zegan <webczat_200@poczta.onet.pl>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a69261e447 upstream.
The "goto err_armclk;" error path already does a clk_put(s3c_freq->hclk);
so this is a double free.
Fixes: 34ee550752 ([CPUFREQ] Add S3C2416/S3C2450 cpufreq driver)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84a21dbdef upstream.
Pass-through devices to VM guest can get updated IRQ affinity
information via irq_set_affinity() when not running in guest mode.
Currently, AMD IOMMU driver in GA mode ignores the updated information
if the pass-through device is setup to use vAPIC regardless of guest_mode.
This could cause invalid interrupt remapping.
Also, the guest_mode bit should be set and cleared only when
SVM updates posted-interrupt interrupt remapping information.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Joerg Roedel <jroedel@suse.de>
Fixes: d98de49a53 ('iommu/amd: Enable vAPIC interrupt remapping mode by default')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73dbd4a423 upstream.
In function amd_iommu_bind_pasid(), the control flow jumps
to label out_free when pasid_state->mm and mm is NULL. And
mmput(mm) is called. In function mmput(mm), mm is
referenced without validation. This will result in a NULL
dereference bug. This patch fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Fixes: f0aac63b87 ('iommu/amd: Don't hold a reference to mm_struct')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 938f1bbe35 upstream.
Even if a host controller's CPU-side MMIO windows into PCI I/O space do
happen to leak into PCI memory space such that it might treat them as
peer addresses, trying to reserve the corresponding I/O space addresses
doesn't do anything to help solve that problem. Stop doing a silly thing.
Fixes: fade1ec055 ("iommu/dma: Avoid PCI host bridge windows")
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 797a8b4d76 upstream.
We wouldn't normally expect ops->attach_dev() to fail, but on IOMMUs
with limited hardware resources, or generally misconfigured systems,
it is certainly possible. We report failure correctly from the external
iommu_attach_device() interface, but do not do so in iommu_group_add()
when attaching to the default domain. The result of failure there is
that the device, group and domain all get left in a broken,
part-configured state which leads to weird errors and misbehaviour down
the line when IOMMU API calls sort-of-but-don't-quite work.
Check the return value of __iommu_attach_device() on the default domain,
and refactor the error handling paths to cope with its failure and clean
up correctly in such cases.
Fixes: e39cb8a3aa ("iommu: Make sure a device is always attached to a domain")
Reported-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7116e115a upstream.
dma_pte_free_level() recurses down the IOMMU page tables and frees
directory pages that are entirely contained in the given PFN range.
Unfortunately, it incorrectly calculates the starting address covered
by the PTE under consideration, which can lead to it clearing an entry
that is still in use.
This occurs if we have a scatterlist with an entry that has a length
greater than 1026 MB and is aligned to 2 MB for both the IOMMU and
physical addresses. For example, if __domain_mapping() is asked to map a
two-entry scatterlist with 2 MB and 1028 MB segments to PFN 0xffff80000,
it will ask if dma_pte_free_pagetable() is asked to PFNs from
0xffff80200 to 0xffffc05ff, it will also incorrectly clear the PFNs from
0xffff80000 to 0xffff801ff because of this issue. The current code will
set level_pfn to 0xffff80200, and 0xffff80200-0xffffc01ff fits inside
the range being cleared. Properly setting the level_pfn for the current
level under consideration catches that this PTE is outside of the range
being cleared.
This patch also changes the value passed into dma_pte_free_level() when
it recurses. This only affects the first PTE of the range being cleared,
and is handled by the existing code that ensures we start our cursor no
lower than start_pfn.
This was found when using dma_map_sg() to map large chunks of contiguous
memory, which immediatedly led to faults on the first access of the
erroneously-deleted mappings.
Fixes: 3269ee0bd6 ("intel-iommu: Fix leaks in pagetable freeing")
Reviewed-by: Benjamin Serebrin <serebrin@google.com>
Signed-off-by: David Dillow <dillow@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33496c3c3d upstream.
Configfs is the interface for ocfs2-tools to set configure to kernel and
$configfs_dir/cluster/$clustername/heartbeat/dead_threshold is the one
used to configure heartbeat dead threshold. Kernel has a default value
of it but user can set O2CB_HEARTBEAT_THRESHOLD in /etc/sysconfig/o2cb
to override it.
Commit 45b997737a ("ocfs2/cluster: use per-attribute show and store
methods") changed heartbeat dead threshold name while ocfs2-tools did
not, so ocfs2-tools won't set this configurable and the default value is
always used. So revert it.
Fixes: 45b997737a ("ocfs2/cluster: use per-attribute show and store methods")
Link: http://lkml.kernel.org/r/1490665245-15374-1-git-send-email-junxiao.bi@oracle.com
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Acked-by: Joseph Qi <jiangqi903@gmail.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbd68d8e84 upstream.
flush_tlb_page() passes a bogus range to flush_tlb_others() and
expects the latter to fix it up. native_flush_tlb_others() has the
fixup but Xen's version doesn't. Move the fixup to
flush_tlb_others().
AFAICS the only real effect is that, without this fix, Xen would
flush everything instead of just the one page on remote vCPUs in
when flush_tlb_page() was called.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Nadav Amit <namit@vmware.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: e7b52ffd45 ("x86/flush_tlb: try flush_tlb_single one by one in flush_tlb_range")
Link: http://lkml.kernel.org/r/10ed0e4dfea64daef10b87fb85df1746999b4dba.1492844372.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ed386ec09 upstream.
When this function fails it just sends a SIGSEGV signal to
user-space using force_sig(). This signal is missing
essential information about the cause, e.g. the trap_nr or
an error code.
Fix this by propagating the error to the only caller of
mpx_handle_bd_fault(), do_bounds(), which sends the correct
SIGSEGV signal to the process.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: fe3d197f84 ('x86, mpx: On-demand kernel allocation of bounds tables')
Link: http://lkml.kernel.org/r/1491488362-27198-1-git-send-email-joro@8bytes.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8eabf42ae5 upstream.
Kernel text KASLR is separated into physical address and virtual
address randomization. And for virtual address randomization, we
only randomiza to get an offset between 16M and KERNEL_IMAGE_SIZE.
So the initial value of 'virt_addr' should be LOAD_PHYSICAL_ADDR,
but not the original kernel loading address 'output'.
The bug will cause kernel boot failure if kernel is loaded at a different
position than the address, 16M, which is decided at compiled time.
Kexec/kdump is such practical case.
To fix it, just assign LOAD_PHYSICAL_ADDR to virt_addr as initial
value.
Tested-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Baoquan He <bhe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 8391c73 ("x86/KASLR: Randomize virtual address separately")
Link: http://lkml.kernel.org/r/1498567146-11990-3-git-send-email-bhe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e25ebfe56 upstream.
The pmd containing memblock_limit is cleared by prepare_page_table()
which creates the opportunity for early_alloc() to allocate unmapped
memory if memblock_limit is not pmd aligned causing a boot-time hang.
Commit 965278dcb8 ("ARM: 8356/1: mm: handle non-pmd-aligned end of RAM")
attempted to resolve this problem, but there is a path through the
adjust_lowmem_bounds() routine where if all memory regions start and
end on pmd-aligned addresses the memblock_limit will be set to
arm_lowmem_limit.
Since arm_lowmem_limit can be affected by the vmalloc early parameter,
the value of arm_lowmem_limit may not be pmd-aligned. This commit
corrects this oversight such that memblock_limit is always rounded
down to pmd-alignment.
Fixes: 965278dcb8 ("ARM: 8356/1: mm: handle non-pmd-aligned end of RAM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb7cf772d8 upstream.
The BAD_MADT_GICC_ENTRY() macro checks if a GICC MADT entry passes
muster from an ACPI specification standpoint. Current macro detects the
MADT GICC entry length through ACPI firmware version (it changed from 76
to 80 bytes in the transition from ACPI 5.1 to ACPI 6.0 specification)
but always uses (erroneously) the ACPICA (latest) struct (ie struct
acpi_madt_generic_interrupt - that is 80-bytes long) length to check if
the current GICC entry memory record exceeds the MADT table end in
memory as defined by the MADT table header itself, which may result in
false negatives depending on the ACPI firmware version and how the MADT
entries are laid out in memory (ie on ACPI 5.1 firmware MADT GICC
entries are 76 bytes long, so by adding 80 to a GICC entry start address
in memory the resulting address may well be past the actual MADT end,
triggering a false negative).
Fix the BAD_MADT_GICC_ENTRY() macro by reshuffling the condition checks
and update them to always use the firmware version specific MADT GICC
entry length in order to carry out boundary checks.
Fixes: b6cfb27737 ("ACPI / ARM64: add BAD_MADT_GICC_ENTRY() macro")
Reported-by: Julien Grall <julien.grall@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Julien Grall <julien.grall@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Al Stone <ahs3@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06e1a5cc57 upstream.
The manufacturing information is stored in the EEPROM. This chip
is an AT24C64 not not (nor has it ever been) 24C02. This patch will
correctly address the EEPROM to read the entire contents and not just
256 bytes (of 0xff).
Fixes: 5e3447a29a ("ARM: dts: LogicPD Torpedo: Add AT24 EEPROM Support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04abaf07f6 upstream.
Starting from commit 5de85b9d57 ("PM / runtime: Re-init runtime PM
states at probe error and driver unbind") pm_runtime core now changes
device runtime_status back to after RPM_SUSPENDED after a probe defer.
Certain OMAP devices make use of "ti,no-idle-on-init" flag which causes
omap_device_enable to be called during the BUS_NOTIFY_ADD_DEVICE event
during probe, along with pm_runtime_set_active.
This call to pm_runtime_set_active typically will prevent a call to
pm_runtime_get in a driver probe function from re-enabling the
omap_device. However, in the case of a probe defer that happens before
the driver probe function is able to run, such as a missing pinctrl
states defer, pm_runtime_reinit will set the device as RPM_SUSPENDED and
then once driver probe is actually able to run, pm_runtime_get will see
the device as suspended and call through to the omap_device layer,
attempting to enable the already enabled omap_device and causing errors
like this:
omap-gpmc 50000000.gpmc: omap_device: omap_device_enable() called from
invalid state 1
omap-gpmc 50000000.gpmc: use pm_runtime_put_sync_suspend() in driver?
We can avoid this error by making sure the pm_runtime status of a device
matches the omap_device state before a probe attempt. By extending the
omap_device bus notifier to act on the BUS_NOTIFY_BIND_DRIVER event we
can check if a device is enabled in omap_device but with a pm_runtime
status of RPM_SUSPENDED and once again mark the device as RPM_ACTIVE to
avoid a second incorrect call to omap_device_enable.
Fixes: 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind")
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6308f1787f upstream.
When we check for additional DT properties in the current node we
use the device_node passed in with the configuration data, this
will not point to the correct DT node, use the one passed in
for this purpose.
Fixes: d2a2e729a6 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Reported-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c47f7c316 upstream.
The three load switches are called SWA1, SWB1, and SWB2. The
node names describing properties for these are expected to be
the same, but due to a typo they are not. Fix this here.
Fixes: d2a2e729a6 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Reported-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8324147f38 upstream.
Make sure to release the device-node reference taken in
of_register_spi_device() on errors and when deregistering the device.
Fixes: 284b018973 ("spi: Add OF binding support for SPI busses")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88b0aa544a upstream.
Back before commit 1dccb598df ("arm64: simplify dma_get_ops"), for
arm64, devices for which dma_ops were not explicitly set were automatically
configured to use swiotlb_dma_ops, since this was hard-coded as the
global "dma_ops" in arm64_dma_init().
Now that global "dma_ops" has been removed, all devices much have their
dma_ops explicitly set by a call to arch_setup_dma_ops(), otherwise the
device is assigned dummy_dma_ops, and thus calls to map_sg for such a
device will fail (return 0).
Mediatek SPI uses DMA but does not use a dma channel. Support for this
was added by commit c37f45b5f1 ("spi: support spi without dma channel
to use can_dma()"), which uses the master_spi dev to DMA map buffers.
The master_spi device is not a platform device, rather it is created
in spi_alloc_device(), and therefore its dma_ops are never set.
Therefore, when the mediatek SPI driver when it does DMA (for large SPI
transactions > 32 bytes), SPI will use spi_map_buf()->dma_map_sg() to
map the buffer for use in DMA. But dma_map_sg()->dma_map_sg_attrs() returns
0, because ops->map_sg is dummy_dma_ops->__dummy_map_sg, and hence
spi_map_buf() returns -ENOMEM (-12).
Fix this by using the real spi_master's parent device which should be a
real physical device with DMA properties.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Fixes: c37f45b5f1 ("spi: support spi without dma channel to use can_dma()")
Cc: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e5f32f7a4 upstream.
If we crossed a sample window while in NO_HZ we will add LOAD_FREQ to
the pending sample window time on exit, setting the next update not
one window into the future, but two.
This situation on exiting NO_HZ is described by:
this_rq->calc_load_update < jiffies < calc_load_update
In this scenario, what we should be doing is:
this_rq->calc_load_update = calc_load_update [ next window ]
But what we actually do is:
this_rq->calc_load_update = calc_load_update + LOAD_FREQ [ next+1 window ]
This has the effect of delaying load average updates for potentially
up to ~9seconds.
This can result in huge spikes in the load average values due to
per-cpu uninterruptible task counts being out of sync when accumulated
across all CPUs.
It's safe to update the per-cpu active count if we wake between sample
windows because any load that we left in 'calc_load_idle' will have
been zero'd when the idle load was folded in calc_global_load().
This issue is easy to reproduce before,
commit 9d89c257df ("sched/fair: Rewrite runnable load and utilization average tracking")
just by forking short-lived process pipelines built from ps(1) and
grep(1) in a loop. I'm unable to reproduce the spikes after that
commit, but the bug still seems to be present from code review.
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Fixes: commit 5167e8d ("sched/nohz: Rewrite and fix load-avg computation -- again")
Link: http://lkml.kernel.org/r/20170217120731.11868-2-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29e09229d9 upstream.
inet_sk(skb->sk) is illegal in case skb is attached to request socket.
Fixes: ca6fb06518 ("tcp: attach SYNACK messages to request sockets instead of listener")
Reported by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e3d0c2c70 upstream.
There are some missing error codes here so we accidentally return NULL
instead of an error pointer. It results in a NULL pointer dereference.
Fixes: df71837d50 ("[LSM-IPSec]: Security association restriction.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e747f64336 upstream.
The default error code in pfkey_msg2xfrm_state() is -ENOBUFS. We
added a new call to security_xfrm_state_alloc() which sets "err" to zero
so there several places where we can return ERR_PTR(0) if kmalloc()
fails. The caller is expecting error pointers so it leads to a NULL
dereference.
Fixes: df71837d50 ("[LSM-IPSec]: Security association restriction.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b3eb54106 upstream.
When CONFIG_XFRM_SUB_POLICY=y, xfrm_dst stores a copy of the flowi for
that dst. Unfortunately, the code that allocates and fills this copy
doesn't care about what type of flowi (flowi, flowi4, flowi6) gets
passed. In multiple code paths (from raw_sendmsg, from TCP when
replying to a FIN, in vxlan, geneve, and gre), the flowi that gets
passed to xfrm is actually an on-stack flowi4, so we end up reading
stuff from the stack past the end of the flowi4 struct.
Since xfrm_dst->origin isn't used anywhere following commit
ca116922af ("xfrm: Eliminate "fl" and "pol" args to
xfrm_bundle_ok()."), just get rid of it. xfrm_dst->partner isn't used
either, so get rid of that too.
Fixes: 9d6ec93801 ("ipv4: Use flowi4 in public route lookup interfaces.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 029c54b095 upstream.
Existing code that uses vmalloc_to_page() may assume that any address
for which is_vmalloc_addr() returns true may be passed into
vmalloc_to_page() to retrieve the associated struct page.
This is not un unreasonable assumption to make, but on architectures
that have CONFIG_HAVE_ARCH_HUGE_VMAP=y, it no longer holds, and we need
to ensure that vmalloc_to_page() does not go off into the weeds trying
to dereference huge PUDs or PMDs as table entries.
Given that vmalloc() and vmap() themselves never create huge mappings or
deal with compound pages at all, there is no correct answer in this
case, so return NULL instead, and issue a warning.
When reading /proc/kcore on arm64, you will hit an oops as soon as you
hit the huge mappings used for the various segments that make up the
mapping of vmlinux. With this patch applied, you will no longer hit the
oops, but the kcore contents willl be incorrect (these regions will be
zeroed out)
We are fixing this for kcore specifically, so it avoids vread() for
those regions. At least one other problematic user exists, i.e.,
/dev/kmem, but that is currently broken on arm64 for other reasons.
Link: http://lkml.kernel.org/r/20170609082226.26152-1-ard.biesheuvel@linaro.org
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: zhong jiang <zhongjiang@huawei.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ardb: non-trivial backport to v4.9]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0e9a709560 ]
This fix addresses two problems in the way the DSCP field is formulated
on the encapsulating header of IPv6 tunnels.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195661
1) The IPv6 tunneling code was manipulating the DSCP field of the
encapsulating packet using the 32b flowlabel. Since the flowlabel is
only the lower 20b it was incorrect to assume that the upper 12b
containing the DSCP and ECN fields would remain intact when formulating
the encapsulating header. This fix handles the 'inherit' and
'fixed-value' DSCP cases explicitly using the extant dsfield u8 variable.
2) The use of INET_ECN_encapsulate(0, dsfield) in ip6_tnl_xmit was
incorrect and resulted in the DSCP value always being set to 0.
Commit 90427ef5d2 ("ipv6: fix flow labels when the traffic class
is non-0") caused the regression by masking out the flowlabel
which exposed the incorrect handling of the DSCP portion of the
flowlabel in ip6_tunnel and ip6_gre.
Fixes: 90427ef5d2 ("ipv6: fix flow labels when the traffic class is non-0")
Signed-off-by: Peter Dawson <peter.a.dawson@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 912964eacb ]
Commit 6f29a13061 ("sctp: sctp_addr_id2transport should verify the
addr before looking up assoc") invoked sctp_verify_addr to verify the
addr.
But it didn't check af variable beforehand, once users pass an address
with family = 0 through sockopt, sctp_get_af_specific will return NULL
and NULL pointer dereference will be caused by af->sockaddr_len.
This patch is to fix it by returning NULL if af variable is NULL.
Fixes: 6f29a13061 ("sctp: sctp_addr_id2transport should verify the addr before looking up assoc")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9577b174cd ]
When running SRIOV, warnings for SRQ LIMIT events flood the Hypervisor's
message log when (correct, normally operating) apps use SRQ LIMIT events
as a trigger to post WQEs to SRQs.
Add more information to the existing debug printout for SRQ_LIMIT, and
output the warning messages only for the SRQ CATAS ERROR event.
Fixes: acba2420f9 ("mlx4_core: Add wrapper functions and comm channel and slave event support to EQs")
Fixes: e0debf9cb5 ("mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 613f050d68 ]
Fix to probe on gcc generated functions on modules. Since
probing on a module is based on its symbol name, it should
be adjusted on actual symbols.
E.g. without this fix, perf probe shows probe definition
on non-exist symbol as below.
$ perf probe -m build-x86_64/net/netfilter/nf_nat.ko -F in_range*
in_range.isra.12
$ perf probe -m build-x86_64/net/netfilter/nf_nat.ko -D in_range
p:probe/in_range nf_nat:in_range+0
With this fix, perf probe correctly shows a probe on
gcc-generated symbol.
$ perf probe -m build-x86_64/net/netfilter/nf_nat.ko -D in_range
p:probe/in_range nf_nat:in_range.isra.12+0
This also fixes same problem on online module as below.
$ perf probe -m i915 -D assert_plane
p:probe/assert_plane i915:assert_plane.constprop.134+0
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/148411450673.9978.14905987549651656075.stgit@devbox
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 57d5f64d83 ]
Until now, we allocate memory always with GFP_ATOMIC flag.
When the system is under memory pressure and a user tries to send,
the send fails due to low memory. However, the user application
can wait for free memory if we allocate it using GFP_KERNEL flag.
In this commit, we use allocate memory with GFP_KERNEL for all user
allocation.
Reported-by: Rune Torgersen <runet@innovsys.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 34c55cf2fc ]
Currently dp83867 driver returns error if phy interface type
PHY_INTERFACE_MODE_RGMII_RXID is used to set the rx only internal
delay. Similarly issue happens for PHY_INTERFACE_MODE_RGMII_TXID.
Fix this by checking also the interface type if a particular delay
value is missing in the phy dt bindings. Also update the DT document
accordingly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d2d4edbebe ]
Fix to show correct locations for events on modules by relocating given
address instead of retrying after failure.
This happens when the module text size is big enough, bigger than
sh_addr, because the original code retries with given address + sh_addr
if it failed to find CU DIE at the given address.
Any address smaller than sh_addr always fails and it retries with the
correct address, but addresses bigger than sh_addr will get a CU DIE
which is on the given address (not adjusted by sh_addr).
In my environment(x86-64), the sh_addr of ".text" section is 0x10030.
Since i915 is a huge kernel module, we can see this issue as below.
$ grep "[Tt] .*\[i915\]" /proc/kallsyms | sort | head -n1
ffffffffc0270000 t i915_switcheroo_can_switch [i915]
ffffffffc0270000 + 0x10030 = ffffffffc0280030, so we'll check
symbols cross this boundary.
$ grep "[Tt] .*\[i915\]" /proc/kallsyms | grep -B1 ^ffffffffc028\
| head -n 2
ffffffffc027ff80 t haswell_init_clock_gating [i915]
ffffffffc0280110 t valleyview_init_clock_gating [i915]
So setup probes on both function and see what happen.
$ sudo ./perf probe -m i915 -a haswell_init_clock_gating \
-a valleyview_init_clock_gating
Added new events:
probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)
You can now use it in all perf tools, such as:
perf record -e probe:valleyview_init_clock_gating -aR sleep 1
$ sudo ./perf probe -l
probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
probe:valleyview_init_clock_gating (on i915_vga_set_decode:4@gpu/drm/i915/i915_drv.c in i915)
As you can see, haswell_init_clock_gating is correctly shown,
but valleyview_init_clock_gating is not.
With this patch, both events are shown correctly.
$ sudo ./perf probe -l
probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
Committer notes:
In my case:
# perf probe -m i915 -a haswell_init_clock_gating -a valleyview_init_clock_gating
Added new events:
probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)
You can now use it in all perf tools, such as:
perf record -e probe:valleyview_init_clock_gating -aR sleep 1
# perf probe -l
probe:haswell_init_clock_gating (on i915_getparam+432@gpu/drm/i915/i915_drv.c in i915)
probe:valleyview_init_clock_gating (on __i915_printk+240@gpu/drm/i915/i915_drv.c in i915)
#
# readelf -SW /lib/modules/4.9.0+/build/vmlinux | egrep -w '.text|Name'
[Nr] Name Type Address Off Size ES Flg Lk Inf Al
[ 1] .text PROGBITS ffffffff81000000 200000 822fd3 00 AX 0 0 4096
#
So both are b0rked, now with the fix:
# perf probe -m i915 -a haswell_init_clock_gating -a valleyview_init_clock_gating
Added new events:
probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)
You can now use it in all perf tools, such as:
perf record -e probe:valleyview_init_clock_gating -aR sleep 1
# perf probe -l
probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
#
Both looks correct.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/148411436777.9978.1440275861947194930.stgit@devbox
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3439352916 ]
During interface opening MAC address stored in netdev->dev_addr is
programmed in the HW with exception of BE3 VFs where the initial
MAC is programmed by parent PF. This is OK when MAC address is not
changed when an interfaces is down. In this case the requested MAC is
stored to netdev->dev_addr and later is stored into HW during opening.
But this is not done for all BE3 VFs so the NIC HW does not know
anything about this change and all traffic is filtered.
This is the case of bonding if fail_over_mac == 0 where the MACs of
the slaves are changed while they are down.
The be2net behavior is too restrictive because if a BE3 VF has
the FILTMGMT privilege then it is able to modify its MAC without
any restriction.
To solve the described problem the driver should take care about these
privileged BE3 VFs so the MAC is programmed during opening. And by
contrast unpriviled BE3 VFs should not be allowed to change its MAC
in any case.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d928ae590 ]
BE3 VFs without FILTMGMT privilege are not allowed to modify its MAC,
VLAN table and UC/MC lists. So don't try to delete MAC on such VFs.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fe68d8bfe5 ]
Return value from be_mcc_notify_wait() contains a base completion status
together with an additional status. The base_status() macro need to be
used to access base status.
Fixes: e3a7ae2 be2net: Changing MAC Address of a VF was broken
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ca02954ada ]
USBTrdTim must be programmed to 0x5 when phy has a UTMI+ 16-bit wide
interface or 0x9 when it has a 8-bit wide interface.
GUSBCFG reset value (Value After Reset: 0x1400) sets USBTrdTim to 0x5.
In case of 8-bit UTMI+, without clearing GUSBCFG.USBTRDTIM mask, USBTrdTim
results in 0xD (0x5 | 0x9).
That's why we need to clear GUSBCFG.USBTRDTIM mask before setting USBTrdTim
value, to ensure USBTrdTim is correctly set in case of 8-bit UTMI+.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e991c24d68 ]
We have quite a lot of code that depends on the order of the
__ctl_load inline assemby and subsequent memory accesses, like
e.g. disabling lowcore protection and the writing to lowcore.
Since the __ctl_load macro does not have memory barrier semantics, nor
any other dependencies the compiler is, theoretically, free to shuffle
code around. Or in other words: storing to lowcore could happen before
lowcore protection is disabled.
In order to avoid this class of potential bugs simply add a full
memory barrier to the __ctl_load macro.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 602d9858f0 ]
Some drivers do depend on page mappings to be page aligned.
Swiotlb already enforces such alignment for mappings greater than page,
extend that to page-sized mappings as well.
Without this fix, nvme hits BUG() in nvme_setup_prps(), because that routine
assumes page-aligned mappings.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d22c75d4c ]
If the last section of a core file ends with an unmapped or zero page,
the size of the file does not correspond with the last dump_skip() call.
gdb complains that the file is truncated and can be confusing to users.
After all of the vma sections are written, make sure that the file size
is no smaller than the current file position.
This problem can be demonstrated with gdb's bigcore testcase on the
sparc architecture.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 18e7a45af9 ]
As Peter suggested [1] rejecting non sampling PEBS events,
because they dont make any sense and could cause bugs
in the NMI handler [2].
[1] http://lkml.kernel.org/r/20170103094059.GC3093@worktop
[2] http://lkml.kernel.org/r/1482931866-6018-3-git-send-email-jolsa@kernel.org
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vince@deater.net>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/20170103142454.GA26251@krava
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63cae12bce ]
There is problem with installing an event in a task that is 'stuck' on
an offline CPU.
Blocked tasks are not dis-assosciated from offlined CPUs, after all, a
blocked task doesn't run and doesn't require a CPU etc.. Only on
wakeup do we ammend the situation and place the task on a available
CPU.
If we hit such a task with perf_install_in_context() we'll loop until
either that task wakes up or the CPU comes back online, if the task
waking depends on the event being installed, we're stuck.
While looking into this issue, I also spotted another problem, if we
hit a task with perf_install_in_context() that is in the middle of
being migrated, that is we observe the old CPU before sending the IPI,
but run the IPI (on the old CPU) while the task is already running on
the new CPU, things also go sideways.
Rework things to rely on task_curr() -- outside of rq->lock -- which
is rather tricky. Imagine the following scenario where we're trying to
install the first event into our task 't':
CPU0 CPU1 CPU2
(current == t)
t->perf_event_ctxp[] = ctx;
smp_mb();
cpu = task_cpu(t);
switch(t, n);
migrate(t, 2);
switch(p, t);
ctx = t->perf_event_ctxp[]; // must not be NULL
smp_function_call(cpu, ..);
generic_exec_single()
func();
spin_lock(ctx->lock);
if (task_curr(t)) // false
add_event_to_ctx();
spin_unlock(ctx->lock);
perf_event_context_sched_in();
spin_lock(ctx->lock);
// sees event
So its CPU0's store of t->perf_event_ctxp[] that must not go 'missing'.
Because if CPU2's load of that variable were to observe NULL, it would
not try to schedule the ctx and we'd have a task running without its
counter, which would be 'bad'.
As long as we observe !NULL, we'll acquire ctx->lock. If we acquire it
first and not see the event yet, then CPU0 must observe task_curr()
and retry. If the install happens first, then we must see the event on
sched-in and all is well.
I think we can translate the first part (until the 'must not be NULL')
of the scenario to a litmus test like:
C C-peterz
{
}
P0(int *x, int *y)
{
int r1;
WRITE_ONCE(*x, 1);
smp_mb();
r1 = READ_ONCE(*y);
}
P1(int *y, int *z)
{
WRITE_ONCE(*y, 1);
smp_store_release(z, 1);
}
P2(int *x, int *z)
{
int r1;
int r2;
r1 = smp_load_acquire(z);
smp_mb();
r2 = READ_ONCE(*x);
}
exists
(0:r1=0 /\ 2:r1=1 /\ 2:r2=0)
Where:
x is perf_event_ctxp[],
y is our tasks's CPU, and
z is our task being placed on the rq of CPU2.
The P0 smp_mb() is the one added by this patch, ordering the store to
perf_event_ctxp[] from find_get_context() and the load of task_cpu()
in task_function_call().
The smp_store_release/smp_load_acquire model the RCpc locking of the
rq->lock and the smp_mb() of P2 is the context switch switching from
whatever CPU2 was running to our task 't'.
This litmus test evaluates into:
Test C-peterz Allowed
States 7
0:r1=0; 2:r1=0; 2:r2=0;
0:r1=0; 2:r1=0; 2:r2=1;
0:r1=0; 2:r1=1; 2:r2=1;
0:r1=1; 2:r1=0; 2:r2=0;
0:r1=1; 2:r1=0; 2:r2=1;
0:r1=1; 2:r1=1; 2:r2=0;
0:r1=1; 2:r1=1; 2:r2=1;
No
Witnesses
Positive: 0 Negative: 7
Condition exists (0:r1=0 /\ 2:r1=1 /\ 2:r2=0)
Observation C-peterz Never 0 7
Hash=e427f41d9146b2a5445101d3e2fcaa34
And the strong and weak model agree.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Will Deacon <will.deacon@arm.com>
Cc: jeremy.linton@arm.com
Link: http://lkml.kernel.org/r/20161209135900.GU3174@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
