- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
The 'mtd_writev' interface calls the function assigned
to the '_write' field of a given mtd device if that is
not NULL. The block2mtd driver sets the '_writev' field
to the 'mtd_writev' function itself and thus causes a
endless loop.
This is caused by 1dbebd3256
(mtd: harmonize mtd_writev usage).
Remove the assignment from the block2mtd driver to fix the
issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@kernel.org [3.3+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Corner case reads do not work, and return false data and
ECC. This case is typically seen in a ubifs usage, with a
read of type:
- docg3 docg3: doc_read_oob(from=14882415, mode=1,
data=(c30eca40:12), oob=( (null):0))
This results in the following reads:
- docg3 docg3: doc_read_data_area(buf= (null), len=111)
- docg3 docg3: doc_read_data_area(buf=c30eca40, len=12)
- docg3 docg3: doc_read_data_area(buf= (null), len=389)
- docg3 docg3: doc_read_data_area(buf= (null), len=0)
- docg3 docg3: doc_read_data_area(buf= (null), len=16)
If we suppose that the pages content is :
- bytes 0 .. 111 : 0x0a
- bytes 112 .. 255 : 0x0f
Then the returned bytes will be :
- 111 times 0x0a (correct)
- 0x0a 2 times and 0x0f 10 times (incorrect, should be
0x0a,0x0f)
- 0x0f 389 times (correct)
- nothing
- correct OOB
The reason seams that the first 111 bytes read ends between
the 2 docg3 planes, and that the first following read (in
the 12 bytes sequence, read of 16 bit word) returns the byte
of the rightmost plane duplicated in high and lower byte of
the word.
Fix this behaviour by ensuring that if the previous read
ended up in-between the 2 planes, there will be a first 1
byte read to get back to the beginning of leftmost plane.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Winbond W25Q80BW is a 8Mbit serial flash memory device.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add the id and sector mappings for mx25l2005a flash chips.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The drivers' _read() method, absent an error, returns a non-negative integer
indicating the maximum number of bit errors that were corrected in any one
region comprising an ecc step. MTD returns -EUCLEAN if this is >=
bitflip_threshold, 0 otherwise. If bitflip_threshold is zero, the comparison is
not made since these devices lack ECC and always return zero in the non-error
case (thanks Brian)¹. Note that this is a subtle change to the driver
interface.
This and the preceding patches in this set were tested with ubi on top of the
nandsim and docg4 devices, running the ubi test io_basic from mtd-utils.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-March/040468.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
page_read() never returns NULL, so we can remove the NULL check here.
Signed-off-by: Ryosuke Saito <raitosyo@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
clk_{un}prepare is mandatory for platforms using common clock framework. Since
this driver is used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Merge with latest Linus' tree, as I have incoming patches
that fix code that is newer than current HEAD of for-next.
Conflicts:
drivers/net/ethernet/realtek/r8169.c
Artem's cleanup of the MTD API continues apace.
Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst others.
More work on DiskOnChip G3, new driver for DiskOnChip G4.
Clean up debug/warning printks in JFFS2 to use pr_<level>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk92K6UACgkQdwG7hYl686NrMACfWQJRWasR78MWKfkT2vWZwTFJ
X5AAoKiSYO2pfo5gWJGOAahNC1zUqMX0
=i3Vb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6
Pull MTD changes from David Woodhouse:
- Artem's cleanup of the MTD API continues apace.
- Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst
others.
- More work on DiskOnChip G3, new driver for DiskOnChip G4.
- Clean up debug/warning printks in JFFS2 to use pr_<level>.
Fix up various trivial conflicts, largely due to changes in calling
conventions for things like dmaengine_prep_slave_sg() (new inline
wrapper to hide new parameter, clashing with rewrite of previously last
parameter that used to be an 'append' flag, and is now a bitmap of
'unsigned long flags').
(Also some header file fallout - like so many merges this merge window -
and silly conflicts with sparse fixes)
* tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits)
mtd: docg3 add protection against concurrency
mtd: docg3 refactor cascade floors structure
mtd: docg3 increase write/erase timeout
mtd: docg3 fix inbound calculations
mtd: nand: gpmi: fix function annotations
mtd: phram: fix section mismatch for phram_setup
mtd: unify initialization of erase_info->fail_addr
mtd: support ONFI multi lun NAND
mtd: sm_ftl: fix typo in major number.
mtd: add device-tree support to spear_smi
mtd: spear_smi: Remove default partition information from driver
mtd: Add device-tree support to fsmc_nand
mtd: fix section mismatch for doc_probe_device
mtd: nand/fsmc: Remove sparse warnings and errors
mtd: nand/fsmc: Add DMA support
mtd: nand/fsmc: Access the NAND device word by word whenever possible
mtd: nand/fsmc: Use dev_err to report error scenario
mtd: nand/fsmc: Use devm routines
mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform
mtd: fsmc_nand: add pm callbacks to support hibernation
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
As docg3 is intolerant against reentrancy, especially
because of its weird register access (ie. a register read is
performed by a first register write), each access to the
docg3 IO space must be locked.
Lock the IO space with a mutex, shared by all chips on the
same cascade, as they all share the same IO space.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Group floors into a common cascade structure. This will provide a common
structure to store common data to all cascaded docg3 chips, like IO
addressing, locking protection.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After several tries with ubifs, it appears empirically that constructor
provided figures for erase/write timeouts are underestimated. A timeout
of 100ms seems to work with a 5 years worn chip, and no timeouts occur
anymore.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The last erase block was not accessible, as the out of bound
check was incorrectly rejecting the last block.
The read/write/erase offset checks were forbidding the usage of the
last block, because of the calculation which was considering the
byte after the last instead of the last byte.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
phram_setup() is only called from init_phram() which is in .init.text,
so it must be in the same section to avoid a section mismatch warning.
Signed-off-by: Ryosuke Saito <raitosyo@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support to configure the SPEAr SMI driver via
device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Additionally, after failing in mtd_device_parse_register(), the driver
unmap/free code is now executed.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
doc_probe_device() is only called from docg3_probe() which is in .init.text,
so it must be in the same section to avoid a section mismatch warning.
Signed-off-by: Ryosuke Saito <raitosyo@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch is based on Ville Herva's similar patch to block2mtd.
Trying to pass a parameter through the kernel command line when built-in would
crash the kernel, as phram_setup() was called so early that kmalloc() was not
functional yet.
This patch only saves the parameter string at the early boot stage, and parses
it later when init_phram() is called. The same happens in both module and
built-in cases.
With this patch, I can boot with a statically-compiled phram, and mount a
ext2 root fs from physical RAM, without the need for a initrd.
This has been tested in built-in and module cases, with and without a
parameter string.
Artem: amended comments a bit
Signed-off-by: Hervé Fache <h-fache@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Flash device drivers initialize 'ecc_strength' in struct mtd_info, which is the
maximum number of bit errors that can be corrected in one writesize region.
Drivers using the nand interface intitialize 'strength' in struct nand_ecc_ctrl,
which is the maximum number of bit errors that can be corrected in one ecc step.
Nand infrastructure code translates this to 'ecc_strength'.
Also for nand drivers, the nand infrastructure code sets ecc.strength for ecc
modes NAND_ECC_SOFT, NAND_ECC_SOFT_BCH, and NAND_ECC_NONE. It is set in the
driver for all other modes.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The read function was so far requiring the reads to be aligned on page
boundaries, and be page length multiples in size. Relieve these
constraints to ease the userspace ubifs programs runs, which read ubifs
headers of 64 bytes.
Artem: squashed a later fix from Robert Jarzmik into this patch.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The first 3 arguments of 'mtd_device_parse_register()' are pointers,
but many callers pass '0' instead of 'NULL'. Fix this globally. Thanks
to coccinelle for making it easy to do with the following semantic patch:
@@
expression mtd, types, parser_data, parts, nr_parts;
@@
(
-mtd_device_parse_register(mtd, 0, parser_data, parts, nr_parts)
+mtd_device_parse_register(mtd, NULL, parser_data, parts, nr_parts)
|
-mtd_device_parse_register(mtd, types, 0, parts, nr_parts)
+mtd_device_parse_register(mtd, types, NULL, parts, nr_parts)
|
-mtd_device_parse_register(mtd, types, parser_data, 0, nr_parts)
+mtd_device_parse_register(mtd, types, parser_data, NULL, nr_parts)
)
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Change the name of the mtd so that it is simpler, and is easier to
cope with by mtdparts.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In many places in drivers we verify for the zero length, but this is very
inconsistent across drivers. This is obviously the right thing to do, though.
This patch moves the check to the MTD API functions instead and removes a lot
of duplication.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some MTD drivers return -EINVAL if the 'phys' parameter is not NULL, trying to
convey that they cannot return the physical address. However, this is not very
logical because they still can return the virtual address ('virt'). But some
drivers (lpddr) just ignore the 'phys' parameter instead, which is a more
logical thing to do.
Let's harmonize this and:
1. Always initialize 'virt' and 'phys' to 'NULL' in 'mtd_point()'.
2. Do not return an error if the physical address cannot be found.
So as a result, all drivers will set 'phys' to 'NULL' if it is not supported.
None of the 'mtd_point()' users use 'phys' anyway, so this should not break
anything. I guess we could also just delete this parameter later.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This header is tiny and contains only pmc551-private stuff, so it should
not live in 'include/linux' - let's just merge it with pmc551.c.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The MTD API function now zero the 'retlen' parameter before calling
the driver's method — do not do this again in drivers. This removes
duplicated '*retlen = 0' assignent from the following methods:
'mtd_point()'
'mtd_read()'
'mtd_write()'
'mtd_writev()'
'mtd_panic_write()'
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Many drivers check whether the partition is R/O and return -EROFS if yes.
Let's stop having duplicated checks and move them to the API functions
instead.
And again a bit of noise - deleted few too sparse newlines, sorry.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We already verify that offset and length are within the MTD device size
in the MTD API functions. Let's remove the duplicated checks in drivers.
This patch only affects the following API's:
'mtd_erase()'
'mtd_point()'
'mtd_unpoint()'
'mtd_get_unmapped_area()'
'mtd_read()'
'mtd_write()'
'mtd_panic_write()'
'mtd_lock()'
'mtd_unlock()'
'mtd_is_locked()'
'mtd_block_isbad()'
'mtd_block_markbad()'
This patch adds a bit of noise by removing too sparse empty lines, but this is
not too bad.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The 'mtd_unpoint()' API function should be able to return an error code because
it may fail if you specify incorrect offset. This patch changes this MTD API
function and amends all the drivers correspondingly.
Also return '-EOPNOTSUPP' from 'mtd_unpoint()' when the '->unpoint()' method is
undefined. We do not really need this currently, but this just makes
sense to be consistent with 'mtd_point()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set writebufsize to the flash page size because it is the maximum amount of
data it writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set writebufsize to the flash page size because it is the maximum amount of
data it writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set writebufsize to 4 because this drivers writes at max 4 bytes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@kernel.org [3.2+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
However, we forgot to set this parameter for block2mtd. Set it to PAGE_SIZE
because this is actually the amount of data we write at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Joern Engel <joern@lazybastard.org>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Using UBI on m25p80 can give messages like:
UBI error: io_init: bad write buffer size 0 for 1 min. I/O unit
We need to initialize writebufsize; I think "page_size" is the correct
"bufsize", although I'm not sure. Comments?
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch renames all MTD functions by adding a "_" prefix:
mtd->erase -> mtd->_erase
mtd->read_oob -> mtd->_read_oob
...
The reason is that we are re-working the MTD API and from now on it is
an error to use MTD function pointers directly - we have a corresponding
API call for every pointer. By adding a leading "_" we achieve the following:
1. Make sure we convert every direct pointer users
2. A leading "_" suggests that this interface is internal and it becomes
less likely that people will use them directly
3. Make sure all the out-of-tree modules stop compiling and the owners
spot the big API change and amend them.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch converts the drivers in drivers/mtd/* to use the
module_spi_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Driver must cleanup all held resources during remove. It wasn't
releasing requested memory region.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
SPEAr platforms (spear3xx/spear6xx/spear13xx) provide SMI (Serial Memory
Interface) controller to access serial NOR flash. SMI provides a simple
interface for SPI/serial NOR flashes and has certain inbuilt commands
and features to support these flashes easily. It also makes it possible
to map an address range in order to directly access (read/write) the SNOR
over address bus. This patch intends to provide serial nor driver support
for spear platforms which are accessed through SMI.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since "length" is a u32, the error handling below didn't work when
fixup_pmc551() returns -ENODEV.
if ((length = fixup_pmc551(PCI_Device)) <= 0)
This patch changes both the type of "length" and the return type of
fixup_pmc551() to int.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
CONFIG_GENERIC_IO is just enough for the basic MTD stuff.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAk8Mq/MACgkQdwG7hYl686PeFACfZCgbdDWD9A/JL+i1RMfExVu6
Pi0An3Hmc3PTCp0yQ21KtcKhpF9CAMEu
=NfuL
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.3' of git://git.infradead.org/mtd-2.6
MTD pull for 3.3
* tag 'for-linus-3.3' of git://git.infradead.org/mtd-2.6: (113 commits)
mtd: Fix dependency for MTD_DOC200x
mtd: do not use mtd->block_markbad directly
logfs: do not use 'mtd->block_isbad' directly
mtd: introduce mtd_can_have_bb helper
mtd: do not use mtd->suspend and mtd->resume directly
mtd: do not use mtd->lock, unlock and is_locked directly
mtd: do not use mtd->sync directly
mtd: harmonize mtd_writev usage
mtd: do not use mtd->lock_user_prot_reg directly
mtd: mtd->write_user_prot_reg directly
mtd: do not use mtd->read_*_prot_reg directly
mtd: do not use mtd->get_*_prot_info directly
mtd: do not use mtd->read_oob directly
mtd: mtdoops: do not use mtd->panic_write directly
romfs: do not use mtd->get_unmapped_area directly
mtd: do not use mtd->get_unmapped_area directly
mtd: do use mtd->point directly
mtd: introduce mtd_has_oob helper
mtd: mtdcore: export symbols cleanup
mtd: clean-up the default_mtd_writev function
...
Fix up trivial edit/remove conflict in drivers/staging/spectra/lld_mtd.c
This patch makes the 'mtd_writev()' function more usable and logical. We first
teach it to fall-back to the 'default_mtd_writev()' function if the MTD driver
does not define its own '->writev()' method. Then we make block2mtd and JFFS2
just 'mtd_writev()' instead of 'default_mtd_writev()' function. This means we
can now stop exporting 'default_mtd_writev()' and instead, export
'mtd_writev()'. This is much cleaner and more logical, as well as allows us to
get read of another direct 'mtd->writev' access in JFFS2.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix the following gcc warning:
drivers/mtd/devices/sst25l.c: In function ‘sst25l_probe’:
drivers/mtd/devices/sst25l.c:381:11: warning: unused variable ‘i’ [-Wunused-variable]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The 'struct mtd_info' object is allocated with 'kzalloc()', so it
contains only zeroes - no need to initialize various fields to 0 or
NULL.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Instead of calling 'kmalloc()' and them 'memeset(0)', use 'kzalloc()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As the MTD api has no use for the number of erase cycles
each block has endured, remove the function which calculated
that value.
If one day MTD api finds it usefull for wear levelling
algorithms to have this information, the function should be
put back in place.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch takes into account checkpatch, sparse and ECC
comments.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If doc_probe_device() returned an ERR_PTR, then we accidentally saved
that to docg3_floors[floor] = mtd; which gets derefenced in the error
handling when we call doc_release_device().
I've reworked the error handling to take care of that and hopefully
make it a little simpler.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As each docg3 chip has 2 protection areas (DPS0 and DPS1),
and because theses areas can prevent user access to the chip
data, add for each floor the sysfs entries which insert the
protection key into the right DPS.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Docg3 chips can work in 3 modes : normal MLC mode, fast
mode and reliable mode. Normally, as docg3 is a MLC chip, it
should be configured to work in normal mode.
In both normal mode, each page is distinct. This
means that writing to page 12 of blocks 14,15 writes only to
that page, and reading from page 12 of blocks 14,15 reads
only from that page.
In reliable and fast modes, pages are coupled by pairs, and
are clones one of each other. This means that the available
capacity of the chip is halved. Pages are coupled in each
block, and page of index 2*n contains the same data as page
2*n+1 of the same block.
In fast mode, the reads occur a bit faster, but are a bit
less reliable that in normal mode.
When reading from page 2*n, the chip reads bytes from both
page 2*n and page 2*n+1, makes a logical and for each byte,
and returns the result. As programming a page means
"clearing bits", even if a bit was not cleared on one page
because the flash is worn out, the other page has the bit
cleared, and the result of the "AND" gives a correct result.
When writing to page 2*n, the chip writes data to both page
2*n and page 2*n+1.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add functions to powerdown and powerup from suspend, in
order to save power.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Credit for discovering the BCH algorith parameters, and bit
reversing algorithm is to be give to Mike Dunn and Ivan
Djelic.
The BCH correction code relied upon the BCH library, where
all data and ECC is bit-reversed. The BCH library works
correctly when each input byte is bit-reversed, and
accordingly ECC output is also bit-reversed.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Map the developped write and erase functions into the mtd
structure.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add erase capability to the docg3 driver. The erase block is
made of 2 physical blocks, as both share all 64 pages. That
makes an erase block of at least 64 kBytes.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add write capability to the docg3 driver. The writes are
possible on a single page (512 bytes + 16 bytes), even if
that page is split on 2 physical pages on 2 blocks (each on
one plane).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add OOB buffer area to store the OOB data until the actual
page is written, so that it can be completed by hardware ECC
generator.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add the required registers and commands to erase and write
flash pages / blocks.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add OOB layout description for docg3, so that userspace can
use this information to setup the data for write_oob().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for multiple floors, ie. cascaded docg3
chips. There might be 4 docg3 chips cascaded, sharing the
same address space, and providing up to 4 times the storage
capacity of a unique chip.
Each floor will be seen as an independant mtd device.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix the docg3 reads to be able to cope with all possible
data buffer / oob buffer / file mode combinations from
docg3_read_oob().
This especially ensures that raw reads do not use ECC
corrections, and AUTOOOB and PLACEOOB do use ECC
correction.
The approach is to empty docg3_read() and make it a wrapper
to docg3_read_oob(). As docg3_read_oob() handles all the
funny cases (no data buffer but oob buffer, data buffer but
no oob buffer, ...), docg3_read() is just a special use of
docg3_read_oob().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
BCH registers are contiguous, not on every byte. Fix the
register definitions.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The protection areas boundaries were on 16bit registers, not
8bit. This is consistent with block numbers, which can
extend up to 4096 on bigger chips (and is 2048 on the
docg3).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Writeb was incorrectly traced as a 16 bits write, instead of
a 8 bits write. Fix it by tracing the correct width.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Change the NOP debug log verbosity to very verbose to
unburden log analysis.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move invalidate_bdev, block_sync_page into fs/block_dev.c. Export
kill_bdev as well, so brd doesn't have to open code it. Reduce
buffer_head.h requirement accordingly.
Removed a rather large comment from invalidate_bdev, as it looked a bit
obsolete to bother moving. The small comment replacing it says enough.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Depending on whether MTD_DOCPROBE_ADVANCED is set or not,
MTD_DOCPROBE_ADDRESS will default to either 0x0000 or 0. That should
lead to (basically) identical code in docprobe.c. The current two
defaults should be merged.
And, while we're at it, if MTD_DOCPROBE is set MTD_DOCPROBE_ADDRESS will
always be set. (MTD_DOCPROBE_ADDRESS depends on MTD_DOCPROBE and it has
a default value.) So the check whether CONFIG_MTD_DOCPROBE_ADDRESS is
defined is unnecessary and should be dropped.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
On some platforms such as P3060QDS, has multiple spi flashes, but they are
not available at same time, so if their status is 'disabled', which is set
by u-boot, will not be probed.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Add support for DiskOnChip G3 chips. The support is quite
limited yet :
- no flash writes/erases are implemented
- ECC fixes are not implemented
- powerdown is not implemented
- IPL handling is not yet done
On the brighter side, the chip reading does work.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Add support for EON spi flash EN25Q32B, which is not listed in id table,
need to add it in the id table to support the EON flash.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
These modes are not necessarily for OOB only. Particularly, MTD_OOB_RAW
affected operations on in-band page data as well. To clarify these
options and to emphasize that their effect is applied per-operation, we
change the primary prefix to MTD_OPS_.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Start moving away from the MTD_DEBUG_LEVEL messages. The dynamic
debugging feature is a generic kernel feature that provides more
flexibility.
(See Documentation/dynamic-debug-howto.txt)
Also fix some punctuation, indentation, and capitalization that went
along with the affected lines.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
It adds device tree probe support for mtd_dataflash driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Consolidate knowledge about partitions in drivers/mtd/devices/lart.c.
Drop all HAVE_PARTITIONS conditionals. Always use partitioning.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
I no longer work at Bluewater Systems. Update my email address accordingly. I
have deleted my email address from C files rather than change it. This
was suggested by several people, since the commit from my new email
address will cause scripts/get_maintainer.pl to function properly. I
have not added the .mailmap entry as suggested by Joe because I think
it is no longer necessary if I touch all the files which had my name
in them.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Cc: Andre Renaud <andre@bluewatersys.com>
Cc: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: trivial@kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The older add_mtd_device()/add_mtd_partitions() and their removal
counterparts will soon be gone. Replace uses with mtd_device_register()
and mtd_device_unregister().
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the check for
mtd_has_partitions() as we always have partitioning enabled now.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The previous section mismatch fix for this driver wasn't entirely correct.
The sst25l_flash_info array is now used in the devinit probe func, but is
marked as initdata, so building results in the warning:
WARNING: drivers/mtd/devices/sst25l.o(.devinit.text): Section mismatch
in reference from the function sst25l_probe()
to the variable .init.data:sst25l_flash_info
Further, the remove func should be devexit rather than exit to match the
probe func.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Linus Torvalds