imx: mx6ul_14x14_evk add basic board support
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
supports sd for usdhc2, but can do hardware rework to make usdhc2 support
emmc.
Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-07-20 05:28:35 -06:00
|
|
|
/*
|
|
|
|
* Copyright (C) 2015 Freescale Semiconductor, Inc.
|
|
|
|
*
|
|
|
|
* Configuration settings for the Freescale i.MX6UL 14x14 EVK board.
|
|
|
|
*
|
|
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
|
|
*/
|
|
|
|
#ifndef __MX6UL_14X14_EVK_CONFIG_H
|
|
|
|
#define __MX6UL_14X14_EVK_CONFIG_H
|
|
|
|
|
|
|
|
|
|
|
|
#include <asm/arch/imx-regs.h>
|
|
|
|
#include <linux/sizes.h>
|
|
|
|
#include "mx6_common.h"
|
|
|
|
#include <asm/imx-common/gpio.h>
|
|
|
|
|
imx: mx6ul: support mx6ul 9x9 evk board
This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
supports 512MB DDR3
3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.
This patch add the following:
1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
2. Introduce a macro is_mx6ul_9x9_evk using
CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
mx6ul_14x14_evk. And we have no way to dymaically checking this chip
is 9x9 or 14x14.
3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
POWER related configurations also effect for mx6ul_14x14_evk. But
power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
configurations.
5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
according to board_rev and board_name.
6. Add TARGET_MX6UL_9X9_EVK Kconfig entry
Boot Log:
U-Boot SPL 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53)
reading u-boot.img
reading u-boot.img
U-Boot 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 41C
Reset cause: POR
Board: MX6UL 9x9 EVK
I2C: ready
DRAM: 256 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: FEC1
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-06 01:02:34 -06:00
|
|
|
#define is_mx6ul_9x9_evk() CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK)
|
|
|
|
|
imx: mx6ul_14x14_evk add basic board support
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
supports sd for usdhc2, but can do hardware rework to make usdhc2 support
emmc.
Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-07-20 05:28:35 -06:00
|
|
|
/* SPL options */
|
|
|
|
#define CONFIG_SPL_LIBCOMMON_SUPPORT
|
|
|
|
#define CONFIG_SPL_MMC_SUPPORT
|
|
|
|
#include "imx6_spl.h"
|
|
|
|
|
imx: mx6ul: support mx6ul 9x9 evk board
This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
supports 512MB DDR3
3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.
This patch add the following:
1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
2. Introduce a macro is_mx6ul_9x9_evk using
CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
mx6ul_14x14_evk. And we have no way to dymaically checking this chip
is 9x9 or 14x14.
3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
POWER related configurations also effect for mx6ul_14x14_evk. But
power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
configurations.
5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
according to board_rev and board_name.
6. Add TARGET_MX6UL_9X9_EVK Kconfig entry
Boot Log:
U-Boot SPL 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53)
reading u-boot.img
reading u-boot.img
U-Boot 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 41C
Reset cause: POR
Board: MX6UL 9x9 EVK
I2C: ready
DRAM: 256 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: FEC1
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-06 01:02:34 -06:00
|
|
|
#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
|
|
|
|
|
imx: mx6ul_14x14_evk add basic board support
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
supports sd for usdhc2, but can do hardware rework to make usdhc2 support
emmc.
Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-07-20 05:28:35 -06:00
|
|
|
#define CONFIG_DISPLAY_CPUINFO
|
|
|
|
#define CONFIG_DISPLAY_BOARDINFO
|
|
|
|
|
|
|
|
/* Size of malloc() pool */
|
|
|
|
#define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M)
|
|
|
|
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F
|
|
|
|
#define CONFIG_BOARD_LATE_INIT
|
|
|
|
|
|
|
|
#define CONFIG_MXC_UART
|
|
|
|
#define CONFIG_MXC_UART_BASE UART1_BASE
|
|
|
|
|
|
|
|
/* MMC Configs */
|
|
|
|
#ifdef CONFIG_FSL_USDHC
|
|
|
|
#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
|
|
|
|
|
|
|
|
/* NAND pin conflicts with usdhc2 */
|
|
|
|
#ifdef CONFIG_NAND_MXS
|
|
|
|
#define CONFIG_SYS_FSL_USDHC_NUM 1
|
|
|
|
#else
|
|
|
|
#define CONFIG_SYS_FSL_USDHC_NUM 2
|
|
|
|
#endif
|
|
|
|
|
|
|
|
#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
|
|
|
|
#endif
|
|
|
|
|
|
|
|
/* I2C configs */
|
|
|
|
#define CONFIG_CMD_I2C
|
|
|
|
#ifdef CONFIG_CMD_I2C
|
|
|
|
#define CONFIG_SYS_I2C
|
|
|
|
#define CONFIG_SYS_I2C_MXC
|
2015-09-21 14:43:38 -06:00
|
|
|
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
|
|
|
|
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
|
imx: mx6ul_14x14_evk add basic board support
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
supports sd for usdhc2, but can do hardware rework to make usdhc2 support
emmc.
Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-07-20 05:28:35 -06:00
|
|
|
#define CONFIG_SYS_I2C_SPEED 100000
|
|
|
|
|
imx: mx6ul: support mx6ul 9x9 evk board
This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
supports 512MB DDR3
3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.
This patch add the following:
1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
2. Introduce a macro is_mx6ul_9x9_evk using
CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
mx6ul_14x14_evk. And we have no way to dymaically checking this chip
is 9x9 or 14x14.
3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
POWER related configurations also effect for mx6ul_14x14_evk. But
power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
configurations.
5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
according to board_rev and board_name.
6. Add TARGET_MX6UL_9X9_EVK Kconfig entry
Boot Log:
U-Boot SPL 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53)
reading u-boot.img
reading u-boot.img
U-Boot 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 41C
Reset cause: POR
Board: MX6UL 9x9 EVK
I2C: ready
DRAM: 256 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: FEC1
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-06 01:02:34 -06:00
|
|
|
/* PMIC only for 9X9 EVK */
|
|
|
|
#define CONFIG_POWER
|
|
|
|
#define CONFIG_POWER_I2C
|
|
|
|
#define CONFIG_POWER_PFUZE3000
|
|
|
|
#define CONFIG_POWER_PFUZE3000_I2C_ADDR 0x08
|
|
|
|
#endif
|
imx: mx6ul_14x14_evk add basic board support
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
supports sd for usdhc2, but can do hardware rework to make usdhc2 support
emmc.
Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-07-20 05:28:35 -06:00
|
|
|
|
|
|
|
#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
|
|
|
|
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
|
|
"script=boot.scr\0" \
|
|
|
|
"image=zImage\0" \
|
|
|
|
"console=ttymxc0\0" \
|
|
|
|
"fdt_high=0xffffffff\0" \
|
|
|
|
"initrd_high=0xffffffff\0" \
|
imx: mx6ul: support mx6ul 9x9 evk board
This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
supports 512MB DDR3
3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.
This patch add the following:
1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
2. Introduce a macro is_mx6ul_9x9_evk using
CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
mx6ul_14x14_evk. And we have no way to dymaically checking this chip
is 9x9 or 14x14.
3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
POWER related configurations also effect for mx6ul_14x14_evk. But
power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
configurations.
5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
according to board_rev and board_name.
6. Add TARGET_MX6UL_9X9_EVK Kconfig entry
Boot Log:
U-Boot SPL 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53)
reading u-boot.img
reading u-boot.img
U-Boot 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 41C
Reset cause: POR
Board: MX6UL 9x9 EVK
I2C: ready
DRAM: 256 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: FEC1
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-06 01:02:34 -06:00
|
|
|
"fdt_file=undefined\0" \
|
imx: mx6ul_14x14_evk add basic board support
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
supports sd for usdhc2, but can do hardware rework to make usdhc2 support
emmc.
Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-07-20 05:28:35 -06:00
|
|
|
"fdt_addr=0x83000000\0" \
|
|
|
|
"boot_fdt=try\0" \
|
|
|
|
"ip_dyn=yes\0" \
|
2015-10-29 01:54:48 -06:00
|
|
|
"videomode=video=ctfb:x:480,y:272,depth:24,pclk:108695,le:8,ri:4,up:2,lo:4,hs:41,vs:10,sync:0,vmode:0\0" \
|
imx: mx6ul_14x14_evk add basic board support
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
supports sd for usdhc2, but can do hardware rework to make usdhc2 support
emmc.
Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-07-20 05:28:35 -06:00
|
|
|
"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
|
|
|
|
"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
|
|
|
|
"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
|
|
|
|
"mmcautodetect=yes\0" \
|
|
|
|
"mmcargs=setenv bootargs console=${console},${baudrate} " \
|
|
|
|
"root=${mmcroot}\0" \
|
|
|
|
"loadbootscript=" \
|
|
|
|
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
|
|
|
|
"bootscript=echo Running bootscript from mmc ...; " \
|
|
|
|
"source\0" \
|
|
|
|
"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
|
|
|
|
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
|
|
|
|
"mmcboot=echo Booting from mmc ...; " \
|
|
|
|
"run mmcargs; " \
|
|
|
|
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
|
|
|
|
"if run loadfdt; then " \
|
|
|
|
"bootz ${loadaddr} - ${fdt_addr}; " \
|
|
|
|
"else " \
|
|
|
|
"if test ${boot_fdt} = try; then " \
|
|
|
|
"bootz; " \
|
|
|
|
"else " \
|
|
|
|
"echo WARN: Cannot load the DT; " \
|
|
|
|
"fi; " \
|
|
|
|
"fi; " \
|
|
|
|
"else " \
|
|
|
|
"bootz; " \
|
|
|
|
"fi;\0" \
|
|
|
|
"netargs=setenv bootargs console=${console},${baudrate} " \
|
|
|
|
"root=/dev/nfs " \
|
|
|
|
"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
|
|
|
|
"netboot=echo Booting from net ...; " \
|
|
|
|
"run netargs; " \
|
|
|
|
"if test ${ip_dyn} = yes; then " \
|
|
|
|
"setenv get_cmd dhcp; " \
|
|
|
|
"else " \
|
|
|
|
"setenv get_cmd tftp; " \
|
|
|
|
"fi; " \
|
|
|
|
"${get_cmd} ${image}; " \
|
|
|
|
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
|
|
|
|
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
|
|
|
|
"bootz ${loadaddr} - ${fdt_addr}; " \
|
|
|
|
"else " \
|
|
|
|
"if test ${boot_fdt} = try; then " \
|
|
|
|
"bootz; " \
|
|
|
|
"else " \
|
|
|
|
"echo WARN: Cannot load the DT; " \
|
|
|
|
"fi; " \
|
|
|
|
"fi; " \
|
|
|
|
"else " \
|
|
|
|
"bootz; " \
|
imx: mx6ul: support mx6ul 9x9 evk board
This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
supports 512MB DDR3
3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.
This patch add the following:
1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
2. Introduce a macro is_mx6ul_9x9_evk using
CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
mx6ul_14x14_evk. And we have no way to dymaically checking this chip
is 9x9 or 14x14.
3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
POWER related configurations also effect for mx6ul_14x14_evk. But
power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
configurations.
5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
according to board_rev and board_name.
6. Add TARGET_MX6UL_9X9_EVK Kconfig entry
Boot Log:
U-Boot SPL 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53)
reading u-boot.img
reading u-boot.img
U-Boot 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 41C
Reset cause: POR
Board: MX6UL 9x9 EVK
I2C: ready
DRAM: 256 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: FEC1
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-06 01:02:34 -06:00
|
|
|
"fi;\0" \
|
|
|
|
"findfdt="\
|
|
|
|
"if test $fdt_file = undefined; then " \
|
|
|
|
"if test $board_name = EVK && test $board_rev = 9X9; then " \
|
|
|
|
"setenv fdt_file imx6ul-9x9-evk.dtb; fi; " \
|
|
|
|
"if test $board_name = EVK && test $board_rev = 14X14; then " \
|
|
|
|
"setenv fdt_file imx6ul-14x14-evk.dtb; fi; " \
|
|
|
|
"if test $fdt_file = undefined; then " \
|
|
|
|
"echo WARNING: Could not determine dtb to use; fi; " \
|
|
|
|
"fi;\0" \
|
imx: mx6ul_14x14_evk add basic board support
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
supports sd for usdhc2, but can do hardware rework to make usdhc2 support
emmc.
Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-07-20 05:28:35 -06:00
|
|
|
|
|
|
|
#define CONFIG_BOOTCOMMAND \
|
imx: mx6ul: support mx6ul 9x9 evk board
This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
supports 512MB DDR3
3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.
This patch add the following:
1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
2. Introduce a macro is_mx6ul_9x9_evk using
CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
mx6ul_14x14_evk. And we have no way to dymaically checking this chip
is 9x9 or 14x14.
3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
POWER related configurations also effect for mx6ul_14x14_evk. But
power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
configurations.
5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
according to board_rev and board_name.
6. Add TARGET_MX6UL_9X9_EVK Kconfig entry
Boot Log:
U-Boot SPL 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53)
reading u-boot.img
reading u-boot.img
U-Boot 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 41C
Reset cause: POR
Board: MX6UL 9x9 EVK
I2C: ready
DRAM: 256 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: FEC1
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-06 01:02:34 -06:00
|
|
|
"run findfdt;" \
|
imx: mx6ul_14x14_evk add basic board support
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
supports sd for usdhc2, but can do hardware rework to make usdhc2 support
emmc.
Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-07-20 05:28:35 -06:00
|
|
|
"mmc dev ${mmcdev};" \
|
|
|
|
"mmc dev ${mmcdev}; if mmc rescan; then " \
|
|
|
|
"if run loadbootscript; then " \
|
|
|
|
"run bootscript; " \
|
|
|
|
"else " \
|
|
|
|
"if run loadimage; then " \
|
|
|
|
"run mmcboot; " \
|
|
|
|
"else run netboot; " \
|
|
|
|
"fi; " \
|
|
|
|
"fi; " \
|
|
|
|
"else run netboot; fi"
|
|
|
|
|
|
|
|
/* Miscellaneous configurable options */
|
|
|
|
#define CONFIG_CMD_MEMTEST
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x80000000
|
2016-01-04 23:03:36 -07:00
|
|
|
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x8000000)
|
imx: mx6ul_14x14_evk add basic board support
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
supports sd for usdhc2, but can do hardware rework to make usdhc2 support
emmc.
Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-07-20 05:28:35 -06:00
|
|
|
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
|
|
|
|
#define CONFIG_SYS_HZ 1000
|
|
|
|
|
|
|
|
#define CONFIG_CMDLINE_EDITING
|
|
|
|
#define CONFIG_STACKSIZE SZ_128K
|
|
|
|
|
|
|
|
/* Physical Memory Map */
|
|
|
|
#define CONFIG_NR_DRAM_BANKS 1
|
|
|
|
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
|
|
|
|
|
|
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
|
|
|
|
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
|
|
|
|
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
|
|
|
|
|
|
|
|
#define CONFIG_SYS_INIT_SP_OFFSET \
|
|
|
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
|
|
#define CONFIG_SYS_INIT_SP_ADDR \
|
|
|
|
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
|
|
|
|
|
|
|
|
/* FLASH and environment organization */
|
|
|
|
#define CONFIG_SYS_NO_FLASH
|
|
|
|
|
|
|
|
#define CONFIG_ENV_SIZE SZ_8K
|
|
|
|
#define CONFIG_ENV_IS_IN_MMC
|
|
|
|
#define CONFIG_ENV_OFFSET (8 * SZ_64K)
|
|
|
|
#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 */
|
|
|
|
#define CONFIG_SYS_MMC_ENV_PART 0 /* user area */
|
|
|
|
#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC2 */
|
|
|
|
|
|
|
|
#define CONFIG_CMD_BOOTZ
|
|
|
|
#define CONFIG_CMD_BMODE
|
|
|
|
|
|
|
|
#ifndef CONFIG_SYS_DCACHE_OFF
|
|
|
|
#define CONFIG_CMD_CACHE
|
|
|
|
#endif
|
|
|
|
|
2016-02-17 12:32:14 -07:00
|
|
|
#define CONFIG_FSL_QSPI
|
imx: mx6ul_14x14_evk add basic board support
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
supports sd for usdhc2, but can do hardware rework to make usdhc2 support
emmc.
Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-07-20 05:28:35 -06:00
|
|
|
#ifdef CONFIG_FSL_QSPI
|
|
|
|
#define CONFIG_CMD_SF
|
|
|
|
#define CONFIG_SPI_FLASH
|
|
|
|
#define CONFIG_SPI_FLASH_BAR
|
|
|
|
#define CONFIG_SF_DEFAULT_BUS 0
|
|
|
|
#define CONFIG_SF_DEFAULT_CS 0
|
|
|
|
#define CONFIG_SF_DEFAULT_SPEED 40000000
|
|
|
|
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
|
2016-01-19 00:13:52 -07:00
|
|
|
#define CONFIG_SPI_FLASH_STMICRO
|
imx: mx6ul_14x14_evk add basic board support
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
supports sd for usdhc2, but can do hardware rework to make usdhc2 support
emmc.
Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-07-20 05:28:35 -06:00
|
|
|
#define FSL_QSPI_FLASH_NUM 1
|
|
|
|
#define FSL_QSPI_FLASH_SIZE SZ_32M
|
|
|
|
#endif
|
|
|
|
|
|
|
|
/* USB Configs */
|
|
|
|
#define CONFIG_CMD_USB
|
|
|
|
#ifdef CONFIG_CMD_USB
|
|
|
|
#define CONFIG_USB_EHCI
|
|
|
|
#define CONFIG_USB_EHCI_MX6
|
|
|
|
#define CONFIG_USB_STORAGE
|
|
|
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
|
|
|
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
|
|
|
|
#define CONFIG_MXC_USB_FLAGS 0
|
|
|
|
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
|
|
|
|
#endif
|
|
|
|
|
2015-08-12 03:46:52 -06:00
|
|
|
#ifdef CONFIG_CMD_NET
|
|
|
|
#define CONFIG_FEC_MXC
|
|
|
|
#define CONFIG_MII
|
|
|
|
#define CONFIG_FEC_ENET_DEV 1
|
|
|
|
|
|
|
|
#if (CONFIG_FEC_ENET_DEV == 0)
|
|
|
|
#define IMX_FEC_BASE ENET_BASE_ADDR
|
|
|
|
#define CONFIG_FEC_MXC_PHYADDR 0x2
|
|
|
|
#define CONFIG_FEC_XCV_TYPE RMII
|
|
|
|
#elif (CONFIG_FEC_ENET_DEV == 1)
|
|
|
|
#define IMX_FEC_BASE ENET2_BASE_ADDR
|
|
|
|
#define CONFIG_FEC_MXC_PHYADDR 0x1
|
|
|
|
#define CONFIG_FEC_XCV_TYPE RMII
|
|
|
|
#endif
|
|
|
|
#define CONFIG_ETHPRIME "FEC"
|
|
|
|
|
|
|
|
#define CONFIG_PHYLIB
|
|
|
|
#define CONFIG_PHY_MICREL
|
|
|
|
#endif
|
|
|
|
|
2015-09-02 12:54:13 -06:00
|
|
|
#define CONFIG_IMX_THERMAL
|
imx: mx6ul_14x14_evk add basic board support
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
supports sd for usdhc2, but can do hardware rework to make usdhc2 support
emmc.
Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-07-20 05:28:35 -06:00
|
|
|
|
2016-01-03 21:19:14 -07:00
|
|
|
#ifndef CONFIG_SPL_BUILD
|
2015-10-29 01:54:48 -06:00
|
|
|
#define CONFIG_VIDEO
|
|
|
|
#ifdef CONFIG_VIDEO
|
|
|
|
#define CONFIG_CFB_CONSOLE
|
|
|
|
#define CONFIG_VIDEO_MXS
|
|
|
|
#define CONFIG_VIDEO_LOGO
|
|
|
|
#define CONFIG_VIDEO_SW_CURSOR
|
|
|
|
#define CONFIG_VGA_AS_SINGLE_DEVICE
|
|
|
|
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
|
|
|
|
#define CONFIG_SPLASH_SCREEN
|
|
|
|
#define CONFIG_SPLASH_SCREEN_ALIGN
|
|
|
|
#define CONFIG_CMD_BMP
|
|
|
|
#define CONFIG_BMP_16BPP
|
|
|
|
#define CONFIG_VIDEO_BMP_RLE8
|
|
|
|
#define CONFIG_VIDEO_BMP_LOGO
|
|
|
|
#define MXS_LCDIF_BASE MX6UL_LCDIF1_BASE_ADDR
|
|
|
|
#endif
|
2016-01-03 21:19:14 -07:00
|
|
|
#endif
|
2015-10-29 01:54:48 -06:00
|
|
|
|
imx: mx6ul_14x14_evk add basic board support
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
supports sd for usdhc2, but can do hardware rework to make usdhc2 support
emmc.
Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-07-20 05:28:35 -06:00
|
|
|
#endif
|