small cleanups
parent
305e8b80e6
commit
c01f43f4ea
|
@ -20,10 +20,10 @@ Main hardware components in an optical \gls{ground-station}:
|
|||
\begin{itemize}
|
||||
\item Lens. \index{lens}
|
||||
\item Camera. \index{camera}
|
||||
\item Computer. \index{computer}
|
||||
\item \Gls{embedded system} (computer). \index{embedded system}
|
||||
\end{itemize}
|
||||
\end{mdframed}
|
||||
\index{lens}\index{camera}\index{embedded computer}
|
||||
\index{lens}\index{camera}\index{embedded system}
|
||||
|
||||
Other components:
|
||||
\begin{mdframed}[backgroundcolor=blue!10,linecolor=blue!30]
|
||||
|
@ -82,7 +82,7 @@ Lenses being tested:
|
|||
|
||||
\section{Embedded Computer}
|
||||
\label{sec:hardware-computer}
|
||||
\index{hardware}\index{embedded computer}
|
||||
\index{hardware}\index{embedded system}
|
||||
\Glspl{embedded system}, such as \gls{Raspberry Pi}, that can be used.
|
||||
\index{Raspberry Pi}
|
||||
|
||||
|
@ -98,7 +98,7 @@ Lenses being tested:
|
|||
|
||||
\subsection{Comparison}
|
||||
Comparing \glspl{embedded system} for \gls{SatNOGS-Optical}.
|
||||
\index{embedded computer}
|
||||
\index{embedded system}
|
||||
|
||||
\begin{center}
|
||||
\begin{table}[ht]
|
||||
|
|
|
@ -41,7 +41,7 @@ Note: the SatNOGS network is not yet ready for optical data.
|
|||
|
||||
Setup an \gls{embedded system}, such as a \gls{Raspberry Pi} or an Odroid N2,
|
||||
with \gls{Debian} stable (11/Bullseye) or testing (Bookworm).
|
||||
\index{embedded computer}\index{Odroid}\index{Debian}
|
||||
\index{embedded system}\index{Odroid}\index{Debian}
|
||||
|
||||
See each \gls{software repository} for latest documentation.
|
||||
|
||||
|
@ -340,7 +340,7 @@ Software that can be used with \gls{telescope} tracking mounts:
|
|||
\end{description}
|
||||
\end{mdframed}
|
||||
\index{telescope}\index{INDI}\index{KStars}\index{Ekos}\index{Stellarium}
|
||||
\index{INDIGO}\index{sky charts}
|
||||
\index{INDIGO}\index{sky chart}
|
||||
|
||||
Using \gls{INDI} with \gls{KStars} and Ekos on a Sky-Watcher or \gls{Celestron}
|
||||
\gls{telescope} mount is a known working solution.
|
||||
|
@ -618,7 +618,7 @@ An overview of steps:
|
|||
and \texttt{\gls{V4L2}} for the \gls{CCD}, which will work with The Imaging Source
|
||||
camera used in this example. Alternatively, the ZWO ASI could be used with a similar configuration.
|
||||
\item The Ekos configuration should also be set to use the remote \texttt{indiserver}
|
||||
\gls{IP} address of the embedded computer \gls{USB} connected to the Sky-Watcher mount.
|
||||
\gls{IP} address of the embedded system \gls{USB} connected to the Sky-Watcher mount.
|
||||
\item Hit the start button to start Ekos/\gls{INDI}.
|
||||
\item On the screen that pops up, confirm all the tabs are good.
|
||||
\item Check the last configuration tab for the camera, it often
|
||||
|
|
Loading…
Reference in New Issue