[ Upstream commit 05669b6317 ]
Non-incrementing writes can fail if register + length crosses page
border. However for non-incrementing writes we should not check for page
border crossing. Fix this by passing additional flag to _regmap_raw_write
and passing length to _regmap_select_page basing on the flag.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: cdf6b11daa ("regmap: Add regmap_noinc_write API")
Link: https://lore.kernel.org/r/20200917153405.3139200-2-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4003324856 ]
Non-incrementing reads can fail if register + length crosses page
border. However for non-incrementing reads we should not check for page
border crossing. Fix this by passing additional flag to _regmap_raw_read
and passing length to _regmap_select_page basing on the flag.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 74fe7b551f ("regmap: Add regmap_noinc_read API")
Link: https://lore.kernel.org/r/20200917153405.3139200-1-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Ot99
-----END PGP SIGNATURE-----
Merge tag 'v5.4.67' into 5.4-2.2.x-imx
This is the 5.4.67 stable release
This updates the kernel present in the NXP release imx_5.4.47_2.2.0 to the
latest patchset available from stable korg.
Base stable kernel version present in the NXP BSP release is v5.4.47.
Following conflicts were recorded and resolved:
- arch/arm/mach-imx/pm-imx6.c
NXP version has a different PM vectoring scheme, where the IRAM bottom
half (8k) is used to store IRAM code and pm_info. Keep this version to
be compatible with NXP PM implementation.
- arch/arm64/boot/dts/freescale/imx8mm-evk.dts
- arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
NXP patches kept to provide proper LDO setup:
imx8mm-evk.dts: 975d8ab07267ded741c4c5d7500e524c85ab40d3
imx8mn-ddr4-evk.dts: e8e35fd0e759965809f3dca5979a908a09286198
- drivers/crypto/caam/caamalg.c
Keep NXP version, as it already covers the functionality for the
upstream patch [d6bbd4eea2]
- drivers/gpu/drm/imx/dw_hdmi-imx.c
- drivers/gpu/drm/imx/imx-ldb.c
- drivers/gpu/drm/imx/ipuv3/ipuv3-crtc.c
Port changes from upstream commit [1a27987101], which extends
component lifetime by moving drm structures allocation/free from
bind() to probe().
- drivers/gpu/drm/imx/imx-ldb.c
Merge patch [1752ab50e8] from upstream to disable both LVDS channels
when Enoder is disabled
- drivers/mmc/host/sdhci-esdhc-imx.c
Fix merge fuzz produced by [6534c897fd].
- drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c
Commit d1a00c9bb1 from upstream solves the issue with improper error
reporting when qdisc type support is absent. Upstream version is merged
into NXP implementation.
- drivers/net/ethernet/freescale/enetc/enetc.c
Commit [ce06fcb6a6] from upstream merged,
base NXP version kept
- drivers/net/ethernet/freescale/enetc/enetc_pf.c
Commit [e8b86b4d87] from upstream solves
the kernel panic in case if probing fails. NXP has a clean-up logic
implemented different, where the MDIO remove would be invoked in any
failure case. Keep the NXP logic in place.
- drivers/thermal/imx_thermal.c
Upstream patch [9025a5589c] adds missing
of_node_put call, NXP version has been adapted to accommodate this patch
into the code.
- drivers/usb/cdns3/ep0.c
Manual merge of commit [be8df02707] from
upstream to protect cdns3_check_new_setup
- drivers/xen/swiotlb-xen.c
Port upstream commit cca58a1669 to NXP tree, manual hunk was
resolved during merge.
- sound/soc/fsl/fsl_esai.c
Commit [53057bd4ac] upstream addresses the problem of endless isr in
case if exception interrupt is enabled and tasklet is scheduled. Since
NXP implementation has tasklet removed with commit [2bbe95fe6c],
upstream fix does not match the main implementation, hence we keep the
NXP version here.
- sound/soc/fsl/fsl_sai.c
Apply patch [b8ae2bf5cc] from upstream, which uses FIFO watermark
mask macro.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
[ Upstream commit e84861fec3 ]
This function is used by dev_get_regmap() to retrieve a regmap for the
specified device. If the device has more than one regmap, the name parameter
can be used to specify one.
The code here uses a pointer comparison to check for equal strings. This
however will probably always fail, as the regmap->name is allocated via
kstrdup_const() from the regmap's config->name.
Fix this by using strcmp() instead.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200703103315.267996-1-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53d860952c ]
The assembly and disassembly of data to be sent to or received from
a device invoke functions regmap_format_XX() and regmap_parse_XX()
that extract or insert data items from or into a buffer, using
assignments. In some cases the functions are called with a buffer
pointer with an odd address. On architectures with strict alignment
requirements this can result in a kernel crash. The assignments
have been replaced by functions that take alignment into account.
Signed-off-by: Jens Thoms Toerring <jt@toerring.de>
Link: https://lore.kernel.org/r/20200531095300.GA27570@toerring.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95b2c3ec4c ]
When a register patch is registered the reg_sequence is copied but the
memory allocated is never freed. Add a kfree in regmap_exit to clean it
up.
Fixes: 22f0d90a34 ("regmap: Support register patch sets")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200617152129.19655-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2e31aab08b upstream.
When checking if a register block is writable we must ensure that the
block does not start with or contain a non incrementing register.
Fixes: 8b9f9d4dc5 ("regmap: verify if register is writeable before writing operations")
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://lore.kernel.org/r/20200118205625.14532-1-ben.whitten@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 9b947a13e7.
The commit 9b947a13e7 does not consider power and
clock when expose the regmap into debugsfs. This may bring some problem for some
case. E.g., For reset registers (not real GPR, but csi bridge register) for
MIPI DSI, MIPI CSI and LCDIF on i.mx8mm, they only can be accessed after the
disp_root clock and dispmix power has been turned on, otherwise the system may
be stuck.
on i.mx8mm evk, the command to reproduce (with default dtb, no display/capture
running):
cat /sys/kernel/debug/regmap/dummy-display-gpr@32e28000/registers
This patch reverted previous commit to avoid the exposure.
Signed-off-by: Robby Cai <robby.cai@nxp.com>
Reviewed-by: Fancy Fang <chen.fang@nxp.com>
On buses like SlimBus and SoundWire which does not support
gather_writes yet in regmap, A bulk write on paged register
would be silently ignored after programming page.
This is because local variable 'ret' value in regmap_raw_write_impl()
gets reset to 0 once page register is written successfully and the
code below checks for 'ret' value to be -ENOTSUPP before linearising
the write buffer to send to bus->write().
Fix this by resetting the 'ret' value to -ENOTSUPP in cases where
gather_writes() is not supported or single register write is
not possible.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There were a few files in the regmap code that did not have SPDX
identifiers on them, so fix that up. At the same time, remove the "free
form" text that specified the license of the file, as that is impossible
for any tool to properly parse.
Also, as Mark loves // comment markers, convert all of the headers to be
the same to make things look consistent :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap provides a couple of ways to validate the register range used.
a) maxim allowed register, b) writable/readable register tables,
c) callback function that can be provided by the driver to validate
a register. regmap framework should verify if registers
are writeable before every write operation. However this doesn't
seems to happen in every situation.
The method `_regmap_raw_write_impl` is only using the `writeable_reg`
callback to verify if register is writeable, ignoring the other two.
This can lead to undefined behaviour since this allows to write to
registers that could be declared un-writeable by using any other
option.
Change `_regmap_raw_write_impl` to use the `regmap_writeable` method
to verify if registers are writable before the write operation.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the checking of the LOG_DEVICE into a function to reduce the
number of #ifdefs and ensure more of the code gets compiled/checked,
and make it easier to change this for internal debugging purposes
(such as checking >1 device).
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap API had a noinc_read function added for instances where devices
supported returning data from an internal FIFO in a single read.
This commit adds the noinc_write variant to allow writing to a non
incrementing register, this is used in devices such as the sx1301 for
loading firmware.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap API usually assumes that bulk read operations will read a
range of registers but some I2C/SPI devices have certain registers for
which a such a read operation will return data from an internal FIFO
instead. Add an explicit API to support bulk read without range semantics.
Some linux drivers use regmap_bulk_read or regmap_raw_read for such
registers, for example mpu6050 or bmi150 from IIO. This only happens to
work because when caching is disabled a single regmap read op will map
to a single bus read op (as desired). This breaks if caching is enabled and
reg+1 happens to be a cacheable register.
Without regmap support refactoring a driver to enable regmap caching
requires separate I2C and SPI paths. This is exactly what regmap is
supposed to help avoid.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The handling for the first two cases in regmap_bulk_write is
essentially identical. The first case is just a better implementation of
the second, supporting 8 byte registers and doing the locking manually to
avoid bouncing the lock for each register. Drop some redundant code by
removing the second of these cases and allowing both situations to be
handled by the same code.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Raw writes may need to be split into small chunks if max_raw_write is
set. Tidy up the code implementing this, the new code is slightly
clearer, slightly shorter and slightly more efficient.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently regmap_bulk_write will split a write into chunks before
calling regmap_raw_write if max_raw_write is set. It is more logical
for this handling to be inside regmap_raw_write itself, as this
removes the need to keep re-implementing the chunking code, which
would be the same for all users of regmap_raw_write.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the case were the bulk transaction is split up into smaller chunks
data is passed directly to regmap_raw_write. However regmap_bulk_write
uses data in host endian and regmap_raw_write expects data in device
endian. As such if the host and device differ in endian the wrong data
will be written to the device. Correct this issue using a similar
approach to the single raw write case below it, duplicate the data
into a new buffer and use parse_inplace to format the data correctly.
Fixes: adaac45975 ("regmap: Introduce max_raw_read/write for regmap_bulk_read/write")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This registers regmaps with debugfs even when they do not have an
associated device. For example, this is common for syscon regmaps.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Bulk reads may potentially read a lot of registers and regmap_read will
take and release the regmap lock for each register. Avoid bouncing
the lock so frequently by holding the lock locally and calling
_regmap_read instead. This also has the nice side-effect that all the
reads will be done atomically so no other threads can sneak a write in
during the regmap_bulk_read.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Raw reads may need to be split into small chunks if max_raw_read is
set. Tidy up the code implementing this, the new code is slightly
clearer, slightly shorter and slightly more efficient.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently regmap_bulk_read will split a read into chunks before
calling regmap_raw_read if max_raw_read is set. It is more logical for
this handling to be inside regmap_raw_read itself, as this removes the
need to keep re-implementing the chunking code, which would be the
same for all users of regmap_raw_read.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a helper function exists for calculating register offsets lets use
that rather than open coding with the reg_stride.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A bulk read can be implemented either through regmap_raw_read, or
by reading each register individually using regmap_read. Both
regmap_read and regmap_bulk_read should return values in native
endian. In the individual case the current implementation calls
format_val to put the data into the output array, which can cause
endian issues. The regmap_read will have already converted the data
into native endian, if the hosts endian differs from the device then
format_val will switch the endian back again.
Rather than using format_val simply use the code that is called if
there is no format_val function. This code supports all cases except
24-bit but there don't appear to be any users of regmap_bulk_read for
24-bit. Additionally, it would have to be a big endian host for the
old code to actually function correctly anyway.
Fixes: 15b8d2c41f ("regmap: Fix regmap_bulk_read in BE mode")
Reported-by: David Rhodes <david.rhodes@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The cache pointer points to the actual memory used by the cache, as the
comparison here is looking for the type of the cache it should check
against cache_type.
Fixes: 1ea975cf1e ("regmap: Add a function to check if a regmap register is cached")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current implementation is broken for regmaps that have a reg_stride,
since it doesn't take the stride into account. Correct this by using the
helper function to calculate the register offset.
Fixes: f01ee60fff ("regmap: implement register striding")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We're supposed to be checking that "val_len" is not too large but
instead we check if it is smaller than the max.
The only function affected would be regmap_i2c_smbus_i2c_write() in
drivers/base/regmap/regmap-i2c.c. Strangely that function has its own
limit check which returns an error if (count >= I2C_SMBUS_BLOCK_MAX) so
it doesn't look like it has ever been able to do anything except return
an error.
Fixes: c335931ed9 ("regmap: Add raw_write/read checks for max_raw_write/read sizes")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
All zero read and write masks in the regmap config are used to signal no
special mask is needed and the bus defaults are used. In some devices
all zero read/write masks are the special mask and bus defaults should
not be used. To signal this a new variable is added.
For example SPI often sets bit 7 in address to signal to the device a
read is requested. On TI AFE44xx parts with SPI interfaces no bit
needs to be set as registers are either read or write only and the
operation can be determined from the address only. For this case both
masks must be zero to not effect the address.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the hwlock id 0 is valid for hardware spinlock core, but now id 0
is treated as one invalid value for regmap. Thus we should add one extra
flag for regmap config to indicate if a hardware spinlock should be used,
then id 0 can be valid for regmap to request.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The map->work_buf is a buffer preallocated in __regmap_init() with size
allowing it to store all 3 parts of a buffer - reg, pad and val. While
reg and val parts are always properly setup before each transaction, the
pad part is left at its default value (zeros). Until it is overwritten,
that is.
_regmap_bus_read(), when calling _regmap_raw_read() uses beginning of
work_buf as a place to store data read. Usually that is fine but if
val_bits > reg_bits && pad_bits > 0, padding area of work_buf() may get
overwritten. Since padding is not zeroed before each transaction,
garbage will be used on next calls.
This patch moves the val pointer used for _regmap_raw_read() to point
to a part of work_buf intended for storing value read.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we just copy over the pointer passed to regmap_init() in
the regmap config struct. To be on the safe side: duplicate the string
with kstrdup_const() so that if an unaware user passes an address to
a stack-allocated buffer, we won't crash.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
The recently added support for disabling the regmap internal locking left
debugfs enabled for devices with the locking disabled. This is a problem
since debugfs allows userspace to do things like initiate reads from the
hardware which will use the scratch buffers protected by the regmap locking
so could cause data corruption.
For safety address this by just disabling debugfs for these devices. That
is overly conservative since some of the debugfs files just read internal
data structures but it's much simpler to implmement and less likely to
lead to problems with tooling that works with debugfs.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Minor naming convention tweak.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have a use case in the at24 EEPROM driver (recently converted to
using regmap instead of raw i2c/smbus calls) where we read from/write
to the regmap in a loop, while protecting the entire loop with
a mutex.
Currently this implicitly makes us use two mutexes - one in the driver
and one in regmap. While browsing the code for similar use cases I
noticed a significant number of places where locking *seems* redundant.
Allow users to completely disable any locking mechanisms in regmap
config.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hwspinlock was changed to a bool by commit d048236dfd
("hwspinlock: Change hwspinlock to a bool"), so we do not need
the REGMAP_HWSPINLOCK config to select hwspinlock or not.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the warning of label 'err_map' defined but not used.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Andrey Zhizhikin