[ Upstream commit 782b6b6984 ]
Use noirq suspend/resume callbacks as other drivers which implement
noirq suspend/resume callbacks (Ex:- PCIe) depend on pinctrl driver to
configure the signals used by their respective devices in the noirq phase.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200604174935.26560-1-vidyas@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds pinctrl register read to flush all the prior pinctrl
writes and then adds barrier for pinctrl register read to complete
during resume to make sure all pinctrl changes are effective.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1565984527-5272-3-git-send-email-skomatineni@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pmx_writel uses writel which inserts write barrier before the
register write.
This patch has fix to replace writel with writel_relaxed followed
by a readback and memory barrier to ensure write operation is
completed for successful pinctrl change.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1565984527-5272-2-git-send-email-skomatineni@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for Tegra pinctrl driver suspend and resume.
During suspend, context of all pinctrl registers are stored and
on resume they are all restored to have all the pinmux and pad
configuration for normal operation.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1564607463-28802-2-git-send-email-skomatineni@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
Core changes:
- Device links can optionally be added between a pin control
producer and its consumers. This will affect how the system
power management is handled: a pin controller will not suspend
before all of its consumers have been suspended. This was
necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense
to make this default in the long run. Right now it is
opt-in per driver.
- Drive strength can be specified in microamps. With decreases
in silicon technology, milliamps isn't granular enough, let's
make it possible to select drive strengths in microamps. Right
now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a
product line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in
addition to muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken
aside and not usable for users. This is used in ACPI systems
to take out some GPIO lines used by the BIOS so that
noone else (neither kernel nor userspace) will play with them
by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board
management controllers for servers) in preparation for the
new Aspeed AST2600 SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=Wdw1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
Some pin groups have park bits for multiple pins in one register.
Support this by turning the parked bit field into a parked bitmask
field. If no parked bits are supported, the bitmask can be 0.
Update the pingroup table on Tegra210, which is the only generation
where this is supported, with the parked bitmask.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rather than reuse the nvidia,tegra30-gpio compatible string
to find the GPIO controller on Tegra30, Tegra114, Tegra124 and
Tegra210, use the most specific compatible string for each
SoC generation for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tegra194 has PCIE L5 rst and clkreq pins which need to be controlled
dynamically at runtime. This driver supports change pinmux for these
pins. Pinmux for rest of the pins is set statically by bootloader and
will not be changed by this driver
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Signed-off-by: Suresh Mangipudi <smangipudi@nvidia.com>
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra194 chip has 32 bit pinctrl registers. Existing register defines in
header are only 16 bit.
Modified common pinctrl-tegra driver to support 32 bit registers of
Tegra 194 and later chips.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No user of tegra_pinctrl_probe can be built as a module, hence
exporting the symbol is not necessary. Drop EXPORT_SYMBOL_GPL.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a bug in regards to deferred probing within the drivers core
that causes GPIO-driver to suspend after its users. The bug appears if
GPIO-driver probe is getting deferred, which happens after introducing
dependency on PINCTRL-driver for the GPIO-driver by defining "gpio-ranges"
property in device-tree. The bug in the drivers core is old (more than 4
years now) and is well known, unfortunately there is no easy fix for it.
The good news is that we can workaround the deferred probe issue by
changing GPIO / PINCTRL drivers registration order and hence by moving
PINCTRL driver registration to the arch_init level and GPIO to the
subsys_init.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra 2 uses a different GPIO controller which uses "tegra20-gpio" as
compatible string.
Make the compatible string the GPIO node is using a SoC specific
property. This prevents the kernel from registering the GPIO range
twice in case the GPIO range is specified in the device tree.
Fixes: 9462510ce3 ("pinctrl: tegra: Only set the gpio range if needed")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Muxing of pins MCLK1/2 determine the muxing of the corresponding clocks.
Make pinctrl driver to provide clock muxes for the CDEV1/2 pingroups, so
that main clk-controller driver could get an actual parent clock for the
CDEV1/2 clocks.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Omit extra messages for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only. All
drivers get similar changes, so they are handled in batch.
We remove module.h from code that isn't doing anything modular at
all; if they have __init sections, then replace it with init.h.
A couple drivers have module_exit() code that is essentially orphaned,
and so we remove that.
Quite a few bool drivers (hence non-modular) are converted over to
to builtin_platform_driver().
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Pritesh Raithatha <praithatha@nvidia.com>
Cc: Ashwini Ghuge <aghuge@nvidia.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 53d2a715c2 ("phy: Add Tegra XUSB pad controller support") added
a new driver for the XUSB pad controller that implements a more flexible
devicetree binding. In order to preserve backwards compatibility the old
driver can be probed if the obsolete bindings are detected.
In order to hide the legacy code, these prototypes were defined in a
header private to the new driver. This has the disadvantage of making
the sparse code checker complain about the missing declarations when
compiling the old driver and suggesting to make the functions static.
Avoid these sparse warnings by adding local prototype declarations into
the compatibility driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New drivers:
- New driver for Oxnas pin control and GPIO. This ARM-based chipset
is used in a few storage (NAS) type devices.
- New driver for the MAX77620/MAX20024 pin controller portions.
- New driver for the Intel Merrifield pin controller.
New subdrivers:
- New subdriver for the Qualcomm MDM9615
- New subdriver for the STM32F746 MCU
- New subdriver for the Broadcom NSP SoC.
Cleanups:
- Demodularization of bool compiled-in drivers.
Apart from this there is just regular incremental improvements to
a lot of drivers, especially Uniphier and PFC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=po0g
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.8 kernel cycle.
Nothing stands out as especially exiting: new drivers, new subdrivers,
lots of cleanups and incremental features.
Business as usual.
New drivers:
- New driver for Oxnas pin control and GPIO. This ARM-based chipset
is used in a few storage (NAS) type devices.
- New driver for the MAX77620/MAX20024 pin controller portions.
- New driver for the Intel Merrifield pin controller.
New subdrivers:
- New subdriver for the Qualcomm MDM9615
- New subdriver for the STM32F746 MCU
- New subdriver for the Broadcom NSP SoC.
Cleanups:
- Demodularization of bool compiled-in drivers.
Apart from this there is just regular incremental improvements to a
lot of drivers, especially Uniphier and PFC"
* tag 'pinctrl-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (131 commits)
pinctrl: fix pincontrol definition for marvell
pinctrl: xway: fix typo
Revert "pinctrl: amd: make it explicitly non-modular"
pinctrl: iproc: Add NSP and Stingray GPIO support
pinctrl: Update iProc GPIO DT bindings
pinctrl: bcm: add OF dependencies
pinctrl: ns2: remove redundant dev_err call in ns2_pinmux_probe()
pinctrl: Add STM32F746 MCU support
pinctrl: intel: Protect set wake flow by spin lock
pinctrl: nsp: remove redundant dev_err call in nsp_pinmux_probe()
pinctrl: uniphier: add Ethernet pin-mux settings
sh-pfc: Use PTR_ERR_OR_ZERO() to simplify the code
pinctrl: ns2: fix return value check in ns2_pinmux_probe()
pinctrl: qcom: update DT bindings with ebi2 groups
pinctrl: qcom: establish proper EBI2 pin groups
pinctrl: imx21: Remove the MODULE_DEVICE_TABLE() macro
Documentation: dt: Add new compatible to STM32 pinctrl driver bindings
includes: dt-bindings: Add STM32F746 pinctrl DT bindings
pinctrl: sunxi: fix nand0 function name for sun8i
pinctrl: uniphier: remove pointless pin-mux settings for PH1-LD11
...
I got below build error:
ERROR: "tegra_xusb_padctl_legacy_probe"
[drivers/phy/tegra/phy-tegra-xusb.ko] undefined!
with below build configuration:
CONFIG_ARCH_TEGRA=y
CONFIG_PINCTRL_TEGRA_XUSB=y
CONFIG_PHY_TEGRA_XUSB=y
The problem is below line in drivers/pinctrl/Makefile
obj-$(CONFIG_PINCTRL_TEGRA) += tegra/
So even CONFIG_PINCTRL_TEGRA_XUSB=y is set, kbuild still does not compile
the code in drivers/pinctrl/tegra folder if !CONFIG_PINCTRL_TEGRA.
phy-tegra-xusb.c does not use any symbol from pinctrl-tegra.c,
so build pinctrl-tegra.c only when CONFIG_PINCTRL_TEGRA is set.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove the use of parked_reg and use parked_bit for to know
whether field is supported or not.
This is fix for the patch
commit 1d18a3f0f0
"pinctrl: tegra: avoid parked_reg and parked_bank
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable drivers
to use it, saving lots of lines of code all over the place.
New drivers:
- New driver for the Broadcom NS2 SoC.
- New subdriver for the PXA25x SoCs.
- New subdriver for the AMLogic Meson GXBB SoC.
Driver improvements:
- The Intel Baytrail driver now properly supports pin control.
- The Nomadik, Rockchip, Broadcom BCM2835 supports the .get_direction() callback in
the GPIO portions.
- Continued development and stabilization of several SH-PFC
SoC subdrivers: r8a7795, r8a7790, r8a7794 etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tlvn
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This kernel cycle was quite calm when it comes to pin control and
there is really just one major change, and that is the introduction of
devm_pinctrl_register() managed resources.
Apart from that linear development, details below.
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable
drivers to use it, saving lots of lines of code all over the place.
New drivers:
- driver for the Broadcom NS2 SoC
- subdriver for the PXA25x SoCs
- subdriver for the AMLogic Meson GXBB SoC
Driver improvements:
- the Intel Baytrail driver now properly supports pin control
- Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction()
callback in the GPIO portions
- continued development and stabilization of several SH-PFC SoC
subdrivers: r8a7795, r8a7790, r8a7794 etc"
* tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits)
Revert "pinctrl: tegra: avoid parked_reg and parked_bank"
pinctrl: meson: Fix eth_tx_en bit index
pinctrl: tegra: avoid parked_reg and parked_bank
pinctrl: tegra: Correctly check the supported configuration
pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC
pinctrl: rockchip: fix pull setting error for rk3399
pinctrl: stm32: Implement .pin_config_dbg_show()
pinctrl: nomadik: hide nmk_gpio_get_mode when unused
pinctrl: ns2: rename pinctrl_utils_dt_free_map
pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable
pinctrl: at91: Make at91_gpio_template const
pinctrl: baytrail: fix some error handling in debugfs
pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC
pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged
pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove()
pinctrl: nomadik: implement .get_direction()
pinctrl: nomadik: use BIT() with offsets consequently
pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range
pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration
pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration
...
NVIDIA's Tegra210 support the park bit to make pinmux configuration
enable/disable. If parked bit is 1 then configuration does not apply
and if it is 0 then pinmux configuration applies. This is to support
to avoid any glitch in pinmux configurations.
The parked bit is part of mux register and mux bank and hence it is
not required to have member for the parked_reg and parked bank very
similar to other bit field of the same register.
Remove the need of the parked register and parked bank and get whether
parked function supported or not by parked_bit.
This is to make the parked bit handling same as other fields of mux
registers.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pincontrol registers of Tegra chips has multiple filed per
registers. There is two type of registers mux and drive. All
configurations belongs to one of these registers.
If any configurations are supported then <config>_bit is set to
bit position of these registers otherwise -1 to not support it.
The member is defined as
s32 <config>_bit:6;
So if config is not supported ifor given SoC then it is set to -1
in soc pinmmux table.
In common driver code, to find out that given config is supported
or not, it is checked as:
s8 bit = <config>_bit;
if (bit > 31) {
/* Not supported config */
}
But in this case, bit is s8 and hence for non supporting it is -1.
Correct the check as:
if (bit < 0) {
/* Not supported config */
}
Fixes: e4c02dced9 ("pinctrl: tegra: use signed bitfields for optional fields")
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a new driver for the XUSB pad controller found on NVIDIA Tegra SoCs.
This hardware block used to be exposed as a pin controller, but it turns
out that this isn't a good fit. The new driver and DT binding much more
accurately describe the hardware and are more flexible in supporting new
SoC generations.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use devm_pinctrl_register() for pin control registration and clean
the error path.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_pinctrl_register() for pin control registration and remove
need of .remove callback.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Parking bits might not be cleared by the bootloader properly (if for
instance it doesn't use the device configured by that pin). Clear
the park bits for all the pins during pinctrl probe.
This is present on T210 platforms but not earlier ones, so for earlier
generations, set parked_reg = -1 to disable.
The park bit is used to prevent glitching when reprogramming pinctrl
registers.
Based on work by:
Shravani Dingari <shravanid@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename pinctrl_utils_dt_free_map to pinctrl_utils_free_map, since
it does not depend on device tree despite the current name. This
will enforce a consistent naming in pinctr-utils.c and will make
it clear it can be called from outside device tree (e.g. from
ACPI handling code).
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra has several pinctrl drivers. Now it is reasonable enough to
move them into drivers/pinctrl/tegra/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Vidya Sagar