[ Upstream commit d2ee3ff79e ]
The usb_request->zero doesn't apply for isoc. Also, if we prepare a
0-length (ZLP) TRB for the OUT direction, we need to prepare an extra
TRB to pad up to the MPS alignment. Use the same bounce buffer for the
ZLP TRB and the extra pad TRB.
Cc: <stable@vger.kernel.org> # v4.5+
Fixes: d6e5a549cc ("usb: dwc3: simplify ZLP handling")
Fixes: 04c03d10e5 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d187c0454 ]
The SG list may be set up with entry size more than the requested
length. Check the usb_request->length and make sure that we don't setup
the TRBs to send/receive more than requested. This case may occur when
the SG entry is allocated up to a certain minimum size, but the request
length is less than that. It can also occur when the request is reused
for a different request length.
Cc: <stable@vger.kernel.org> # v4.18+
Fixes: a31e63b608 ("usb: dwc3: gadget: Correct handling of scattergather lists")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 20934c0de1 upstream.
The PSZ-HA* family of USB disk drives from Sony can't handle the
REPORT OPCODES command when using the UAS protocol. This patch adds
an appropriate quirks entry.
Reported-and-tested-by: Till Dörges <doerges@pre-sense.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200826143229.GB400430@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4b9d8a582 upstream.
Clang static analysis reports this error
cdc-acm.c:409:3: warning: Use of memory after it is freed
acm_process_notification(acm, (unsigned char *)dr);
There are three problems, the first one is that dr is not reset
The variable dr is set with
if (acm->nb_index)
dr = (struct usb_cdc_notification *)acm->notification_buffer;
But if the notification_buffer is too small it is resized with
if (acm->nb_size) {
kfree(acm->notification_buffer);
acm->nb_size = 0;
}
alloc_size = roundup_pow_of_two(expected_size);
/*
* kmalloc ensures a valid notification_buffer after a
* use of kfree in case the previous allocation was too
* small. Final freeing is done on disconnect.
*/
acm->notification_buffer =
kmalloc(alloc_size, GFP_ATOMIC);
dr should point to the new acm->notification_buffer.
The second problem is any data in the notification_buffer is lost
when the pointer is freed. In the normal case, the current data
is accumulated in the notification_buffer here.
memcpy(&acm->notification_buffer[acm->nb_index],
urb->transfer_buffer, copy_size);
When a resize happens, anything before
notification_buffer[acm->nb_index] is garbage.
The third problem is the acm->nb_index is not reset on a
resizing buffer error.
So switch resizing to using krealloc and reassign dr and
reset nb_index.
Fixes: ea2583529c ("cdc-acm: reassemble fragmented notifications")
Signed-off-by: Tom Rix <trix@redhat.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200801152154.20683-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfd08d06d9 upstream.
Inadvertently the commit b1cd1b65af ("USB: gadget: u_f: add overflow checks
to VLA macros") makes VLA macros to always return 0 due to different scope of
two variables of the same name. Obviously we need to have only one.
Fixes: b1cd1b65af ("USB: gadget: u_f: add overflow checks to VLA macros")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20200826192119.56450-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b74b0a04d upstream.
Some values extracted by ncm_unwrap_ntb() could possibly lead to several
different out of bounds reads of memory. Specifically the values passed
to netdev_alloc_skb_ip_align() need to be checked so that memory is not
overflowed.
Resolve this by applying bounds checking to a number of different
indexes and lengths of the structure parsing logic.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Brooke Basile <brookebasile@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1cd1b65af upstream.
size can potentially hold an overflowed value if its assigned expression
is left unchecked, leading to a smaller than needed allocation when
vla_group_size() is used by callers to allocate memory.
To fix this, add a test for saturation before declaring variables and an
overflow check to (n) * sizeof(type).
If the expression results in overflow, vla_group_size() will return SIZE_MAX.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Brooke Basile <brookebasile@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d41698346 upstream.
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
exynos_ohci_probe(). And when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.
Fixes: 62194244cf ("USB: Add Samsung Exynos OHCI diver")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200826144931.1828-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9aa37788e7 upstream.
This device does not support UAS properly and a similar entry already
exists in drivers/usb/storage/unusual_uas.h. Without this patch,
storage_probe() defers the handling of this device to UAS, which cannot
handle it either.
Tested-by: Brice Goglin <brice.goglin@gmail.com>
Fixes: bc3bdb12bb ("usb-storage: Disable UAS on JMicron SATA enclosure")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Link: https://lore.kernel.org/r/20200825212231.46309-1-tipecaml@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 068834a277 upstream.
The Sound Devices MixPre-D audio card suffers from the same defect
as the Sound Devices USBPre2: an endpoint shared between a normal
audio interface and a vendor-specific interface, in violation of the
USB spec. Since the USB core now treats duplicated endpoints as bugs
and ignores them, the audio endpoint isn't available and the card
can't be used for audio capture.
Along the same lines as commit bdd1b147b8 ("USB: quirks: blacklist
duplicate ep on Sound Devices USBPre2"), this patch adds a quirks
entry saying to ignore ep5in for interface 1, leaving it available for
use with standard audio interface 2.
Reported-and-tested-by: Jean-Christophe Barnoud <jcbarnoud@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Fixes: 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints")
Link: https://lore.kernel.org/r/20200826194624.GA412633@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a469bc9f3 upstream.
PNY Pro Elite USB 3.1 Gen 2 device (SSD) doesn't respond to ATA_12
pass-through command (i.e. it just hangs). If it doesn't support this
command, it should respond properly to the host. Let's just add a quirk
to be able to move forward with other operations.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Link: https://lore.kernel.org/r/2b0585228b003eedcc82db84697b31477df152e0.1597803605.git.thinhn@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1ec7ae6c9 upstream.
Some device drivers call libusb_clear_halt when target ep queue
is not empty. (eg. spice client connected to qemu for usb redir)
Before commit f5249461b5 ("xhci: Clear the host side toggle
manually when endpoint is soft reset"), that works well.
But now, we got the error log:
EP not empty, refuse reset
xhci_endpoint_reset failed and left ep_state's EP_SOFT_CLEAR_TOGGLE
bit still set
So all the subsequent urb sumbits to the ep will fail with the
warn log:
Can't enqueue URB while manually clearing toggle
We need to clear ep_state EP_SOFT_CLEAR_TOGGLE bit after
xhci_endpoint_reset, even if it failed.
Fixes: f5249461b5 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: stable <stable@vger.kernel.org> # v4.17+
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 904df64a5f upstream.
Sometimes re-plugging a USB device during system sleep renders the device
useless:
[ 173.418345] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x14203e2, return 0x10262
...
[ 176.496485] usb 2-4: Waited 2000ms for CONNECT
[ 176.496781] usb usb2-port4: status 0000.0262 after resume, -19
[ 176.497103] usb 2-4: can't resume, status -19
[ 176.497438] usb usb2-port4: logical disconnect
Because PLS equals to XDEV_RESUME, xHCI driver reports U3 to usbcore,
despite of CAS bit is flagged.
So proritize CAS over XDEV_RESUME to let usbcore handle warm-reset for
the port.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0077b1b2c8 upstream.
dci is 0 based and xhci_get_ep_ctx() will do ep index increment to get
the ep context.
[rename dci to ep_index -Mathias]
Cc: stable <stable@vger.kernel.org> # v4.15+
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 531412492c upstream.
lvs_rh_probe() can return some nonnegative value from usb_control_msg()
when it is less than "USB_DT_HUB_NONVAR_SIZE + 2" that is considered as
a failure. Make lvs_rh_probe() return -EINVAL in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200805090643.3432-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07c8434150 ]
If a memory allocation fails within a 'usb_ep_alloc_request()' call, the
already allocated memory must be released.
Fix a mix-up in the code and free the correct requests.
Fixes: c52661d60f ("usb-gadget: Initial merge of target module for UASP + BOT")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b53a19284 ]
The char buffer buf, receives data directly from user space,
so its content might be negative and its elements are left
shifted to form an unsigned integer.
Since left shifting a negative value is undefined behavior, thus
change the char to u8 to elimintate this UB.
Signed-off-by: Changming Liu <charley.ashbringer@gmail.com>
Link: https://lore.kernel.org/r/20200711043018.928-1-charley.ashbringer@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce054039ba ]
Clean up receive processing by dropping the character pointer and
keeping the length argument unchanged throughout the function.
Also make it more apparent that sysrq processing can consume a
characters by adding an explicit continue.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab4cc4ef67 ]
Use an unsigned type for the process-packet buffer argument and give it
a more apt name.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The Mass storage gadget uses another thread (fsg_main_thread) to
disable endpoint after disconnecting with host, if it switches
host as soon as disconnecting the gadget (through sysfs role interface),
the system will hang due to access register during the controller
reset. There is no better way to wait fsg_main_thread to complete
at UDC driver, as a workaround, it adds some delay to wait the
thread has completed. The similar method is used when the cable
is disconnected from the host, and 20ms delay has probed no issue.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
With new platform data introduced, we can use it to pass set_role_post
api and various quirks to dwc3 core driver, and remove the dependency
of dwc3 instance when probe, this can resolve the problem if this
dwc3-imx8mp driver as module load before the dwc3 core driver loaded.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
(cherry picked from commit 1b47d2e3f6090835aedaf04dc538e74f63d130e3)
Since dwc3 glue layer may have its xhci_plat_priv, so pass to xhci plat
driver to handle it.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
(cherry picked from commit 38f26c0e7ddb9190de2e21fc927ca0567b9ceaea)
Considering there are various special handling for different dwc3
based integrations on SoC, introduce platform data to let glue
layer driver to pass those specific hanldings to dwc3 core driver,
like set_role_post and quirk flags for xhci and dwc3.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
(cherry picked from commit 240acf931cd907e17e90cb46172c2ed3092fabae)
Some DRD controllers (eg, dwc3 & cdns3) have PHY management at
their own driver to cover both device and host mode, so add one
priv quirk for such users to skip PHY management from HCD core.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
(cherry picked from commit cc2b8987ac7f255ad4219022a784b3d6ba677c0a)
The if {} condition is duplicated with outer if {} condition.
Reviewed-by: Jun Li <jun.li@nxp.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
(cherry picked from commit d968863bcac6e698cab31ab0f526568ca7047d60)
Some xhci hosts (eg dwc3 and cdns3) do not use OF to create
platform device, they create xhci-plat platform device runtime.
And these platforms may also have quirks, and the quirks could
be supplied by their parent device through platform data.
Reviewed-by: Jun Li <jun.li@nxp.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
(cherry picked from commit b600e087f2f292b30408f25998553e80129a2ed7)
Current tcpm set vbus_charge after set usb data role, it's late for usb
charger detection because the BC charger detection should be done before
usb data role setup to avoid USB enumration is impacted.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
(cherry picked from commit b7baab3f9a9414e60c3f580195a83f7dc9632c10)
To support typec port connects to battery chargers of BC specification,
add the BC charger types and let charger detection module set its type.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
(cherry picked from commit 7801f9a5347345b16fc4039c7b5b612403af0234)
USB role class has 3 state: host, device and none, current dwc3 only
has 2 states: host and device, typec compliance test requires DUT
to stop one specific role USB data when parter removed by set its
to be none, so add none role support by stop current role.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
(cherry picked from commit f6d2550ec1922662c8843e578f36e416ffe36f05)
commit 4387b3dbb0 upstream.
Assign the .throttle and .unthrottle functions to be generic function
in the driver structure to prevent data loss that can otherwise occur
if the host does not enable USB throttling.
Signed-off-by: Brant Merryman <brant.merryman@silabs.com>
Co-developed-by: Phu Luu <phu.luu@silabs.com>
Signed-off-by: Phu Luu <phu.luu@silabs.com>
Link: https://lore.kernel.org/r/57401AF3-9961-461F-95E1-F8AFC2105F5E@silabs.com
[ johan: fix up tags ]
Fixes: 39a66b8d22 ("[PATCH] USB: CP2101 Add support for flow control")
Cc: stable <stable@vger.kernel.org> # 2.6.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7614ff9b7 upstream.
CP210x hardware disables auto-RTS but leaves auto-CTS when in hardware
flow control mode and UART on cp210x hardware is disabled. When
re-opening the port, if auto-CTS is enabled on the cp210x, then auto-RTS
must be re-enabled in the driver.
Signed-off-by: Brant Merryman <brant.merryman@silabs.com>
Co-developed-by: Phu Luu <phu.luu@silabs.com>
Signed-off-by: Phu Luu <phu.luu@silabs.com>
Link: https://lore.kernel.org/r/ECCF8E73-91F3-4080-BE17-1714BC8818FB@silabs.com
[ johan: fix up tags and problem description ]
Fixes: 39a66b8d22 ("[PATCH] USB: CP2101 Add support for flow control")
Cc: stable <stable@vger.kernel.org> # 2.6.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a9cf871518 ]
As per UAC2 spec (ch. 4.7.2), wTotalLength of AC Interface
Header Descriptor "includes the combined length of this
descriptor header and all Clock Source, Unit and Terminal
descriptors."
Thus add its size to its wTotalLength.
Also after recent changes wTotalLength is calculated
dynamically, update static definition of uac2_ac_header_descriptor
accordingly
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33a06f1300 ]
When gadget registration fails, one should not call usb_del_gadget_udc().
Ensure this by setting gadget->udc to NULL. Also in case of a failure
there is no need to disable low-level hardware, so return immiedetly
instead of jumping to error_init label.
This fixes the following kernel NULL ptr dereference on gadget failure
(can be easily triggered with g_mass_storage without any module
parameters):
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter besl=1
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter g_np_tx_fifo_size=1024
dwc2 12480000.hsotg: EPs: 16, dedicated fifos, 7808 entries in SPRAM
Mass Storage Function, version: 2009/09/11
LUN: removable file: (no medium)
no file given for LUN0
g_mass_storage 12480000.hsotg: failed to start g_mass_storage: -22
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000104
pgd = (ptrval)
[00000104] *pgd=00000000
Internal error: Oops: 805 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.8.0-rc5 #3133
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
PC is at usb_del_gadget_udc+0x38/0xc4
LR is at __mutex_lock+0x31c/0xb18
...
Process kworker/0:1 (pid: 12, stack limit = 0x(ptrval))
Stack: (0xef121db0 to 0xef122000)
...
[<c076bf3c>] (usb_del_gadget_udc) from [<c0726bec>] (dwc2_hsotg_remove+0x10/0x20)
[<c0726bec>] (dwc2_hsotg_remove) from [<c0711208>] (dwc2_driver_probe+0x57c/0x69c)
[<c0711208>] (dwc2_driver_probe) from [<c06247c0>] (platform_drv_probe+0x6c/0xa4)
[<c06247c0>] (platform_drv_probe) from [<c0621df4>] (really_probe+0x200/0x48c)
[<c0621df4>] (really_probe) from [<c06221e8>] (driver_probe_device+0x78/0x1fc)
[<c06221e8>] (driver_probe_device) from [<c061fcd4>] (bus_for_each_drv+0x74/0xb8)
[<c061fcd4>] (bus_for_each_drv) from [<c0621b54>] (__device_attach+0xd4/0x16c)
[<c0621b54>] (__device_attach) from [<c0620c98>] (bus_probe_device+0x88/0x90)
[<c0620c98>] (bus_probe_device) from [<c06211b0>] (deferred_probe_work_func+0x3c/0xd0)
[<c06211b0>] (deferred_probe_work_func) from [<c0149280>] (process_one_work+0x234/0x7dc)
[<c0149280>] (process_one_work) from [<c014986c>] (worker_thread+0x44/0x51c)
[<c014986c>] (worker_thread) from [<c0150b1c>] (kthread+0x158/0x1a0)
[<c0150b1c>] (kthread) from [<c0100114>] (ret_from_fork+0x14/0x20)
Exception stack(0xef121fb0 to 0xef121ff8)
...
---[ end trace 9724c2fc7cc9c982 ]---
While fixing this also fix the double call to dwc2_lowlevel_hw_disable()
if dr_mode is set to USB_DR_MODE_PERIPHERAL. In such case low-level
hardware is already disabled before calling usb_add_gadget_udc(). That
function correctly preserves low-level hardware state, there is no need
for the second unconditional dwc2_lowlevel_hw_disable() call.
Fixes: 207324a321 ("usb: dwc2: Postponed gadget registration to the udc class driver")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1b6bed3b5 ]
The function quirks_param_set() takes as argument a const char* pointer
to the new value of the usbcore.quirks parameter. It then casts this
pointer to a non-const char* pointer and passes it to the strsep()
function, which overwrites the value.
Fix this by creating a copy of the value using kstrdup() and letting
that copy be written to by strsep().
Fixes: 027bd6cafd ("usb: core: Add "quirks" parameter for usbcore")
Signed-off-by: Kars Mulder <kerneldev@karsmulder.nl>
Link: https://lore.kernel.org/r/5ee2-5f048a00-21-618c5c00@230659773
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de37458f8c ]
The set-led command is eight bytes long and starts with a command byte
followed by six bytes of RGB data and ends with a byte encoding a
frequency (see iuu_led() and iuu_rgbf_fill_buffer()).
The led activity helpers had a few long-standing bugs which corrupted
the command packets by inserting a second command byte and thereby
offsetting the RGB data and dropping the frequency in non-xmas mode.
In xmas mode, a related off-by-one error left the frequency field
uninitialised.
Fixes: 60a8fc0171 ("USB: add iuu_phoenix driver")
Reported-by: George Spelvin <lkml@sdf.org>
Link: https://lore.kernel.org/r/20200716085056.31471-1-johan@kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fc453d7de ]
GISB bus error kernel panics have been observed during S2 transition
tests on the 7271t platform. The errors are a result of the BDC
interrupt handler trying to access BDC register space after the
system's suspend callbacks have completed.
Adding a suspend hook to the BDC driver that halts the controller before
S2 entry thus preventing unwanted access to the BDC register space during
this transition.
Signed-off-by: Danesh Petigara <danesh.petigara@broadcom.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a95bdfd220 ]
Multiple connects/disconnects can cause a crash on the second
disconnect. The driver had a problem where it would try to send
endpoint commands after it was disconnected which is not allowed
by the hardware. The fix is to only allow the endpoint commands
when the endpoint is connected. This will also fix issues that
showed up when using configfs to create gadgets.
Signed-off-by: Sasi Kumar <sasi.kumar@broadcom.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2468c877da ]
Driver does not release memory for device on error handling paths in
net2280_probe() when gadget_release() is not registered yet.
The patch fixes the bug like in other similar drivers.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1e51e99ed ]
If not clear u3port's dual mode when disable device, the IP
will fail to enter sleep mode when suspend.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-10-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Adding runtime PM control at .set_suspend API, then the controller
driver could align PHY's power status with its runtime PM status.
Power domain needs driver's runtime callback to call its runtime
callback and turn on/off power domain according. So, the runtime
pm callback is a must for power domain supported devices.
With this support added, the subsystem (USB PHY in it) with power
domain supported could enter low power mode, and save the power
accordingly.
Cc: Ranjani Vaidyanathan <ranjani.vaidyanathan@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Per dwc3 databook, if GCTL.SOFITPSYNC is enabled, The DWC_usb3 uses
ref_clk for ITP counter when all the 2.0 ports are suspended.
For this usage, GUCTL.REFCLKPER needs to update to be nano seconds
the period of ref_clk; and GFLADJ.GFLADJ_REFCLK_FLADJ needs to update
to be the frame length adjustment to be applied when SOF/ITP counter is
running on the ref_clk, the value is derived as follows:
FLADJ_REF_CLK_FLADJ=
((125000/ref_clk_period_integer)-(125000/ref_clk_period)) * ref_clk_period where
- the ref_clk_period_integer is the integer value of the ref_clk period
got by truncating the decimal (fractional) value that is programmed in
the GUCTL.REF_CLK_PERIOD field.
- the ref_clk_period is the ref_clk period including the fractional
value.
For imx8mp case, the ref_clk is 24M, so ref_clk_period_integer is 41,
and fladj is 2032.
Review-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Since we leave dwc3 core clocks handled by dwc3 core driver, so
only handle the hsio clock, with this change, we have some follow
up changes on clocks handling:
1. 32KHz suspend clk is not required to handle by SW, because it's
always on, so just put it in dwc3 core node to map the real clks
meaning(bus/ref/suspend), not handle it in this glue layer driver,
this means it will be "off" from SW point view.
2. In host mode, dwc3 core clocks are not off while runtime suspend,
so it's better keep the hsio clock on as well, considering this
and easy handling, we keep the hsio clocks on while runtime pm, only
gate it off while system pm.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
commit ec37198acc upstream.
I've confirmed that the ASMedia ASM1142 has the same problem as the
ASM2142/ASM3142, in that it too reports that it supports 64-bit DMA
addresses when in fact it does not. As with the ASM2142/ASM3142, this
can cause problems on systems where the upper bits matter, and adding
the XHCI_NO_64BIT_SUPPORT quirk completely fixes the issue.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200728042408.180529-3-cyrozap@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1841cb255d upstream.
Not all ASMedia host controllers have a device ID that matches its part
number. #define some of these IDs to make it clearer at a glance which
chips require what quirks.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Link: https://lore.kernel.org/r/20200728042408.180529-2-cyrozap@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17a8271658 upstream.
In previous patches that added support for new iowarrior devices, the
handling of the report size was not done correct.
Fix that up and update the copyright date for the driver
Reworked from an original patch written by Christoph Jung.
Fixes: bab5417f5f ("USB: misc: iowarrior: add support for the 100 device")
Fixes: 5f6f8da2d7 ("USB: misc: iowarrior: add support for the 28 and 28L devices")
Fixes: 461d8deb26 ("USB: misc: iowarrior: add support for 2 OEMed devices")
Cc: stable <stable@kernel.org>
Reported-by: Christoph Jung <jung@codemercs.com>
Link: https://lore.kernel.org/r/20200726094939.1268978-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2a4309c1a upstream.
When running qmi-firmware-update on the Sierra Wireless EM7305 in a Toshiba
laptop, it changed product ID to 0x9062 when entering QDL mode:
usb 2-4: new high-speed USB device number 78 using xhci_hcd
usb 2-4: New USB device found, idVendor=1199, idProduct=9062, bcdDevice= 0.00
usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-4: Product: EM7305
usb 2-4: Manufacturer: Sierra Wireless, Incorporated
The upgrade could complete after running
# echo 1199 9062 > /sys/bus/usb-serial/drivers/qcserial/new_id
qcserial 2-4:1.0: Qualcomm USB modem converter detected
usb 2-4: Qualcomm USB modem converter now attached to ttyUSB0
Signed-off-by: Erik Ekman <erik@kryo.se>
Link: https://lore.kernel.org/r/20200717185118.3640219-1-erik@kryo.se
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the controller is in low power mode, it needs to skip pullup
operation since it is meaningless, meanwhile, it is not allowed
from current design, show warning message for it.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
- Delete the duplicated EP_CMD_ERDY and EP_CMD_REQ_CMPL setting
- Prepare the next setup before setting EP_CMD_ERDY and EP_CMD_REQ_CMPL,
it could avoid a bug that DMA hang at EP0 OUT for DEV_VER_NXP_V1
- Delete the duplicated cdns3_set_hw_configuration calling at
cdns3_req_ep0_set_configuration, the composite.c will handle
this request, and call .ep0_queue back, and at .ep_queue it will
call cdns3_set_hw_configuration.
(This patch is porting from upstream with some tiny changes)
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The other thread may access other endpoints when the cdns3_check_new_setup
is handling, add spinlock to protect it.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200623030918.8409-4-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should use the correct direction value from register, not depends
on previous software setting. It fixed the EP number wrong issue at
trace when the TRBERR interrupt occurs for EP0IN.
When the EP0IN IOC has finished, software prepares the setup packet
request, the expected direction is OUT, but at that time, the TRBERR
for EP0IN may occur since it is DMULT mode, the DMA does not stop
until TRBERR has met.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200623030918.8409-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbb0897e80 upstream.
The ASM2142/ASM3142 (same PCI IDs) does not support full 64-bit DMA
addresses, which can cause silent memory corruption or IOMMU errors on
platforms that use the upper bits. Add the XHCI_NO_64BIT_SUPPORT quirk
to fix this issue.
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200717112734.328432-1-cyrozap@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ce1a24dd9 upstream.
The wMaxPacketSize field of endpoint descriptor may be zero
as default value in alternate interface, and they are not
actually selected when start stream, so skip them when try to
allocate bandwidth.
Cc: stable <stable@vger.kernel.org>
Fixes: 0cbd4b34cd ("xhci: mediatek: support MTK xHCI host controller")
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1594360672-2076-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 65b7cf48c2 ]
It is found by sparse.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f81d45c79 ]
It is found by sparse.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8f8529e2c ]
gr_ep_init() does not assign the allocated request anywhere if allocation
of memory for the buffer fails. This is a memory leak fixed by the given
patch.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e25d1e8532 ]
This patch adds the necessary PCI ID for Intel Jasper Lake
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3f595a811 ]
This patch adds the necessary PCI ID for TGP-H devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5d0136f8e7 upstream.
Add PID for CH340 that's found on some ESP8266 dev boards made by
LilyGO. The specific device that contains such serial converter can be
seen here: https://github.com/LilyGO/LILYGO-T-OI.
Apparently, it's a regular CH340, but I've confirmed with others that
also bought this board that the PID found on this device (0x7522)
differs from other devices with the "same" converter (0x7523).
Simply adding its PID to the driver and rebuilding it made it work
as expected.
Signed-off-by: Igor Moura <imphilippini@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c45d04c50 upstream.
This is a UPB (Universal Powerline Bus) PIM (Powerline Interface Module)
which allows for controlling multiple UPB compatible devices from Linux
using the standard serial interface.
Based on vendor application source code there are two different models
of USB based PIM devices in addition to a number of RS232 based PIM's.
The vendor UPB application source contains the following USB ID's:
#define USB_PCS_VENDOR_ID 0x04b4
#define USB_PCS_PIM_PRODUCT_ID 0x5500
#define USB_SAI_VENDOR_ID 0x17dd
#define USB_SAI_PIM_PRODUCT_ID 0x5500
The first set of ID's correspond to the PIM variant sold by Powerline
Control Systems while the second corresponds to the Simply Automated
Incorporated PIM. As the product ID for both of these match the default
cypress HID->COM RS232 product ID it assumed that they both use an
internal variant of this HID->COM RS232 converter hardware. However
as the vendor ID for the Simply Automated variant is different we need
to also add it to the cypress_M8 driver so that it is properly
detected.
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Link: https://lore.kernel.org/r/20200616220403.1807003-1-james.hilliard1@gmail.com
Cc: stable@vger.kernel.org
[ johan: amend VID define entry ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7b931bee7 upstream.
The driver would happily overwrite its write buffer with user data in
256 byte increments due to a removed buffer-space sanity check.
Fixes: 5fcf62b0f1 ("tty: iuu_phoenix: fix locking.")
Cc: stable <stable@vger.kernel.org> # 2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8778eb0927 upstream.
Add a missing spinlock protection for play_queue, because
the play_queue may be destroyed when the "playback_work"
work func and "f_audio_out_ep_complete" callback func
operate this paly_queue at the same time.
Fixes: c6994e6f06 ("USB: gadget: add USB Audio Gadget driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Zhang Qiang <qiang.zhang@windriver.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 876d4e1e82 upstream.
If wakeup event occurred by extcon event, it needs to call
ci_irq again since the first ci_irq calling at extcon notifier
only wakes up controller, but do noop for event handling,
it causes the extcon use case can't work well from low power mode.
Cc: <stable@vger.kernel.org>
Fixes: 3ecb3e09b0 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Reported-by: Philippe Schenker <philippe.schenker@toradex.com>
Tested-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200707060601.31907-2-peter.chen@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fdf228cdf upstream.
To avoid lot of interrupts from dwc2 core, which can be asserted in
specific conditions need to disable interrupts on HW level instead of
disable IRQs on Kernel level, because of IRQ can be shared between
drivers.
Cc: stable@vger.kernel.org
Fixes: a40a00318c ("usb: dwc2: add shutdown callback to platform variant")
Tested-by: Frank Mori Hess <fmh6jj@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Frank Mori Hess <fmh6jj@gmail.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 211f083473 upstream.
clang static analysis flags this error
c67x00-sched.c:489:55: warning: Use of memory after it is freed [unix.Malloc]
usb_hcd_giveback_urb(c67x00_hcd_to_hcd(c67x00), urb, urbp->status);
^~~~~~~~~~~~
Problem happens in this block of code
c67x00_release_urb(c67x00, urb);
usb_hcd_unlink_urb_from_ep(c67x00_hcd_to_hcd(c67x00), urb);
spin_unlock(&c67x00->lock);
usb_hcd_giveback_urb(c67x00_hcd_to_hcd(c67x00), urb, urbp->status);
In the call to c67x00_release_urb has this freeing of urbp
urbp = urb->hcpriv;
urb->hcpriv = NULL;
list_del(&urbp->hep_node);
kfree(urbp);
And so urbp is freed before usb_hcd_giveback_urb uses it as its 3rd
parameter.
Since all is required is the status, pass the status directly as is
done in c64x00_urb_dequeue
Fixes: e9b29ffc51 ("USB: add Cypress c67x00 OTG controller HCD driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200708131243.24336-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 30517ffeb3 ]
Fixed commit moved the assignment of 'req', but did not update a
reference in the DBG() call. Use the argument as it was renamed.
Fixes: 5fb694f96e ("usb: gadget: udc: atmel: fix possible oops when unloading module")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 57a1cd87ef.
Eugeniu Rosca writes:
On Thu, Jul 09, 2020 at 09:00:23AM +0200, Eugeniu Rosca wrote:
>After integrating v4.14.186 commit 5410d158ca2a50 ("usb/ehci-platform:
>Set PM runtime as active on resume") into downstream v4.14.x, we started
>to consistently experience below panic [1] on every second s2ram of
>R-Car H3 Salvator-X Renesas reference board.
>
>After some investigations, we concluded the following:
> - the issue does not exist in vanilla v5.8-rc4+
> - [bisecting shows that] the panic on v4.14.186 is caused by the lack
> of v5.6-rc1 commit 987351e1ea ("phy: core: Add consumer device
> link support"). Getting evidence for that is easy. Reverting
> 987351e1ea in vanilla leads to a similar backtrace [2].
>
>Questions:
> - Backporting 987351e1ea ("phy: core: Add consumer device
> link support") to v4.14.187 looks challenging enough, so probably not
> worth it. Anybody to contradict this?
> - Assuming no plans to backport the missing mainline commit to v4.14.x,
> should the following three v4.14.186 commits be reverted on v4.14.x?
> * baef809ea497a4 ("usb/ohci-platform: Fix a warning when hibernating")
> * 9f33eff4958885 ("usb/xhci-plat: Set PM runtime as active on resume")
> * 5410d158ca2a50 ("usb/ehci-platform: Set PM runtime as active on resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 335d720bb4.
Eugeniu Rosca writes:
On Thu, Jul 09, 2020 at 09:00:23AM +0200, Eugeniu Rosca wrote:
>After integrating v4.14.186 commit 5410d158ca2a50 ("usb/ehci-platform:
>Set PM runtime as active on resume") into downstream v4.14.x, we started
>to consistently experience below panic [1] on every second s2ram of
>R-Car H3 Salvator-X Renesas reference board.
>
>After some investigations, we concluded the following:
> - the issue does not exist in vanilla v5.8-rc4+
> - [bisecting shows that] the panic on v4.14.186 is caused by the lack
> of v5.6-rc1 commit 987351e1ea ("phy: core: Add consumer device
> link support"). Getting evidence for that is easy. Reverting
> 987351e1ea in vanilla leads to a similar backtrace [2].
>
>Questions:
> - Backporting 987351e1ea ("phy: core: Add consumer device
> link support") to v4.14.187 looks challenging enough, so probably not
> worth it. Anybody to contradict this?
> - Assuming no plans to backport the missing mainline commit to v4.14.x,
> should the following three v4.14.186 commits be reverted on v4.14.x?
> * baef809ea497a4 ("usb/ohci-platform: Fix a warning when hibernating")
> * 9f33eff4958885 ("usb/xhci-plat: Set PM runtime as active on resume")
> * 5410d158ca2a50 ("usb/ehci-platform: Set PM runtime as active on resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit fbf719e5da.
Eugeniu Rosca writes:
On Thu, Jul 09, 2020 at 09:00:23AM +0200, Eugeniu Rosca wrote:
>After integrating v4.14.186 commit 5410d158ca2a50 ("usb/ehci-platform:
>Set PM runtime as active on resume") into downstream v4.14.x, we started
>to consistently experience below panic [1] on every second s2ram of
>R-Car H3 Salvator-X Renesas reference board.
>
>After some investigations, we concluded the following:
> - the issue does not exist in vanilla v5.8-rc4+
> - [bisecting shows that] the panic on v4.14.186 is caused by the lack
> of v5.6-rc1 commit 987351e1ea ("phy: core: Add consumer device
> link support"). Getting evidence for that is easy. Reverting
> 987351e1ea in vanilla leads to a similar backtrace [2].
>
>Questions:
> - Backporting 987351e1ea ("phy: core: Add consumer device
> link support") to v4.14.187 looks challenging enough, so probably not
> worth it. Anybody to contradict this?
> - Assuming no plans to backport the missing mainline commit to v4.14.x,
> should the following three v4.14.186 commits be reverted on v4.14.x?
> * baef809ea497a4 ("usb/ohci-platform: Fix a warning when hibernating")
> * 9f33eff4958885 ("usb/xhci-plat: Set PM runtime as active on resume")
> * 5410d158ca2a50 ("usb/ehci-platform: Set PM runtime as active on resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2655971ad4 ]
dwc3_pci_resume_work() calls pm_runtime_get_sync() that increments
the reference counter. In case of failure, decrement the reference
before returning.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Indicate the controller has stream capability, it is useful for UAS
device.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
[ Upstream commit ea0efd687b ]
This driver assumed that dmaengine_tx_status() could return
the residue even if the transfer was completed. However,
this was not correct usage [1] and this caused to break getting
the residue after the commit 24461d9792 ("dmaengine:
virt-dma: Fix access after free in vchan_complete()") actually.
So, this is possible to get wrong received size if the usb
controller gets a short packet. For example, g_zero driver
causes "bad OUT byte" errors.
The usb-dmac driver will support the callback_result, so this
driver can use it to get residue correctly. Note that even if
the usb-dmac driver has not supported the callback_result yet,
this patch doesn't cause any side-effects.
[1]
https://lore.kernel.org/dmaengine/20200616165550.GP2324254@vkoul-mobl/
Reported-by: Hien Dang <hien.dang.eb@renesas.com>
Fixes: 24461d9792 ("dmaengine: virt-dma: Fix access after free in vchan_complete()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1592482277-19563-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e55f3c37cb ]
If this is in "transceiver" mode the the ->qwork isn't required and is
a NULL pointer. This can lead to a NULL dereference when we call
destroy_workqueue(udc->qwork).
Fixes: 3517c31a8e ("usb: gadget: mv_udc: use devm_xxx for probe")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 03894573f2 upstream.
USB_DEVICE(0x0424, 0x274e) can send data before cdc_acm is ready,
causing garbage chars on the TTY causing stray input to the shell
and/or login prompt.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200605105418.22263-1-joakim.tjernlund@infinera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0c472a6da upstream.
Just return if xHCI is quirked to disable LPM. We can save some time
from reading registers and doing spinlocks.
Add stable tag as we want this patch together with the next one,
"Poll for U0 after disabling USB2 LPM" which fixes a suspend issue
for some USB2 LPM devices
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a73d9d9cfc upstream.
Unable to complete the enumeration of a USB TV Tuner device.
Per XHCI spec (4.6.5), the EP state field of the input context shall
be cleared for a set address command. In the special case of an FS
device that has "MaxPacketSize0 = 8", the Linux XHCI driver does
not do this before evaluating the context. With an XHCI controller
that checks the EP state field for parameter context error this
causes a problem in cases such as the device getting reset again
after enumeration.
When that field is cleared, the problem does not occur.
This was found and fixed by Sasi Kumar.
Cc: stable@vger.kernel.org
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dceea67058 upstream.
EP_STATE_MASK should be 0x7 instead of 0xf
xhci spec 6.2.3 shows that the EP state field in the endpoint context data
structure consist of bits [2:0].
The old value included a bit from the next field which fortunately is a
RsvdZ region. So hopefully this hasn't caused too much harm
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2587a029fa upstream.
The other thread may access other endpoints when the cdns3_check_new_setup
is handling, add spinlock to protect it.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b51e1cf64f upstream.
The 'tmode' is ctrl->wIndex, changing it as the real test
mode value for register assignment.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba3a80fe0f upstream.
It should use the correct direction value from register, not depends
on previous software setting. It fixed the EP number wrong issue at
trace when the TRBERR interrupt occurs for EP0IN.
When the EP0IN IOC has finished, software prepares the setup packet
request, the expected direction is OUT, but at that time, the TRBERR
for EP0IN may occur since it is DMULT mode, the DMA does not stop
until TRBERR has met.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 302c570bf3 upstream.
John reported screaming irq caused by rt1711h when system boot[1],
this is because irq request is done before tcpci_register_port(),
so the chip->tcpci has not been setup, irq handler is entered but
can't do anything, this patch is to address this by moving the irq
request after tcpci_register_port().
[1] https://lore.kernel.org/linux-usb/20200530040157.31038-1-john.stultz@linaro.org
Fixes: ce08eaeb63 ("staging: typec: rt1711h typec chip driver")
Cc: stable <stable@vger.kernel.org> # v4.18+
Cc: John Stultz <john.stultz@linaro.org>
Reported-and-tested-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20200604112118.38062-1-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44ed240d62 upstream.
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
exynos_ehci_probe(). And when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.
Fixes: 1bcc5aa87f ("USB: Add initial S5P EHCI driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20200602114708.28620-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3d71abd13 upstream.
USB2 devices with LPM enabled may interrupt the system suspend:
[ 932.510475] usb 1-7: usb suspend, wakeup 0
[ 932.510549] hub 1-0:1.0: hub_suspend
[ 932.510581] usb usb1: bus suspend, wakeup 0
[ 932.510590] xhci_hcd 0000:00:14.0: port 9 not suspended
[ 932.510593] xhci_hcd 0000:00:14.0: port 8 not suspended
..
[ 932.520323] xhci_hcd 0000:00:14.0: Port change event, 1-7, id 7, portsc: 0x400e03
..
[ 932.591405] PM: pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 returns -16
[ 932.591414] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -16
[ 932.591418] PM: Device 0000:00:14.0 failed to suspend async: error -16
During system suspend, USB core will let HC suspends the device if it
doesn't have remote wakeup enabled and doesn't have any children.
However, from the log above we can see that the usb 1-7 doesn't get bus
suspended due to not in U0. After a while the port finished U2 -> U0
transition, interrupts the suspend process.
The observation is that after disabling LPM, port doesn't transit to U0
immediately and can linger in U2. xHCI spec 4.23.5.2 states that the
maximum exit latency for USB2 LPM should be BESL + 10us. The BESL for
the affected device is advertised as 400us, which is still not enough
based on my testing result.
So let's use the maximum permitted latency, 10000, to poll for U0
status to solve the issue.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a24d5072e8 upstream.
When runtime suspend was enabled, runtime suspend might happen
when xhci is removing hcd. This might cause kernel panic when hcd
has been freed but runtime pm suspend related handle need to
reference it.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ddcb71a3e upstream.
A Synopsys USB2.0 core used in Huawei Kunpeng920 SoC has a bug which
might cause the host controller not issuing ping.
Bug description:
After indicating an Interrupt on Async Advance, the software uses the
doorbell mechanism to delete the Next Link queue head of the last
executed queue head. At this time, the host controller still references
the removed queue head(the queue head is NULL). NULL reference causes
the host controller to lose the USB device.
Solution:
After deleting the Next Link queue head, when has_synopsys_hc_bug set
to 1，the software can write one of the valid queue head addresses to
the ASYNCLISTADDR register to allow the host controller to get
the valid queue head. in order to solve that problem, this patch set
the flag for Huawei Kunpeng920
There are detailed instructions and solutions in this patch:
commit 2f7ac6c199 ("USB: ehci: add workaround for Synopsys HC bug")
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1591588019-44284-1-git-send-email-liulongfang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d8021923e upstream.
The Logitech C922, just like other Logitech webcams,
needs the USB_QUIRK_DELAY_INIT or it will randomly
not respond after device connection
Signed-off-by: Tomasz Meresiński <tomasz@meresinski.eu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200603203347.7792-1-tomasz@meresinski.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 207324a321 upstream.
During dwc2 driver probe, after gadget registration to the udc class
driver, if exist any builtin function driver it immediately bound to
dwc2 and after init host side (dwc2_hcd_init()) stucked in host mode.
Patch postpone gadget registration after host side initialization done.
Fixes: 117777b2c3 ("usb: dwc2: Move gadget probe function into platform code")
Reported-by: kbuild test robot <lkp@intel.com>
Tested-by: Marek Vasut <marex@denx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/f21cb38fecc72a230b86155d94c7e60c9cb66f58.1591690938.git.hminas@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07c112fb09 upstream.
This driver misses calling iounmap() in remove to undo the ioremap()
called in probe.
Add the missed call to fix it.
Fixes: f54aab6ebc ("usb: ohci-sm501 driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200610024844.3628408-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cc7eac1e4a ]
Since EHCI/OHCI controllers on R-Car Gen3 SoCs are possible to
be getting stuck very rarely after a full/low usb device was
disconnected. To detect/recover from such a situation, the controllers
require a special way which poll the EHCI PORTSC register and changes
the OHCI functional state.
So, this patch adds a polling timer into the ehci-platform driver,
and if the ehci driver detects the issue by the EHCI PORTSC register,
the ehci driver removes a companion device (= the OHCI controller)
to change the OHCI functional state to USB Reset once. And then,
the ehci driver adds the companion device again.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1580114262-25029-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d363120aa ]
This patch adds new config_ep_by_speed_and_alt function which
extends the config_ep_by_speed about alt parameter.
This additional parameter allows to find proper usb_ss_ep_comp_descriptor.
Problem has appeared during testing f_tcm (BOT/UAS) driver function.
f_tcm function for SS use array of headers for both BOT/UAS alternate
setting:
static struct usb_descriptor_header *uasp_ss_function_desc[] = {
(struct usb_descriptor_header *) &bot_intf_desc,
(struct usb_descriptor_header *) &uasp_ss_bi_desc,
(struct usb_descriptor_header *) &bot_bi_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_ss_bo_desc,
(struct usb_descriptor_header *) &bot_bo_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_intf_desc,
(struct usb_descriptor_header *) &uasp_ss_bi_desc,
(struct usb_descriptor_header *) &uasp_bi_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_bi_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_bo_desc,
(struct usb_descriptor_header *) &uasp_bo_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_bo_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_status_desc,
(struct usb_descriptor_header *) &uasp_status_in_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_status_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_cmd_desc,
(struct usb_descriptor_header *) &uasp_cmd_comp_desc,
(struct usb_descriptor_header *) &uasp_cmd_pipe_desc,
NULL,
};
The first 5 descriptors are associated with BOT alternate setting,
and others are associated with UAS.
During handling UAS alternate setting f_tcm driver invokes
config_ep_by_speed and this function sets incorrect companion endpoint
descriptor in usb_ep object.
Instead setting ep->comp_desc to uasp_bi_ep_comp_desc function in this
case set ep->comp_desc to uasp_ss_bi_desc.
This is due to the fact that it searches endpoint based on endpoint
address:
for_each_ep_desc(speed_desc, d_spd) {
chosen_desc = (struct usb_endpoint_descriptor *)*d_spd;
if (chosen_desc->bEndpoitAddress == _ep->address)
goto ep_found;
}
And in result it uses the descriptor from BOT alternate setting
instead UAS.
Finally, it causes that controller driver during enabling endpoints
detect that just enabled endpoint for bot.
Signed-off-by: Jayshri Pawar <jpawar@cadence.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44734a5941 ]
m66592_free_request() is called under label "err_add_udc"
and "clean_up", and m66592->ep0_req is not set to NULL after
first free, leading to a double-free. Fix this issue by
setting m66592->ep0_req to NULL after the first free.
Fixes: 0f91349b89 ("usb: gadget: convert all users to the new udc infrastructure")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eafa800416 ]
Currently pointer ep is being dereferenced before it is null checked
leading to a null pointer dereference issue. Fix this by only assigning
pointer udc once ep is known to be not null. Also remove a debug
message that requires a valid udc which may not be possible at that
point.
Addresses-Coverity: ("Dereference before null check")
Fixes: 24a28e4283 ("USB: gadget driver for LPC32xx")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a0fbcf7c3 ]
Clang warns:
drivers/usb/gadget/udc/s3c2410_udc.c:255:11: warning: comparison of
address of 'ep->queue' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (&ep->queue == NULL)
~~~~^~~~~ ~~~~
1 warning generated.
It is not wrong, queue is not a pointer so if ep is not NULL, the
address of queue cannot be NULL. No other driver does a check like this
and this check has been around since the driver was first introduced,
presumably with no issues so it does not seem like this check should be
something else. Just remove it.
Commit afe956c577 ("kbuild: Enable -Wtautological-compare") exposed
this but it is not the root cause of the warning.
Fixes: 3fc154b6b8 ("USB Gadget driver for Samsung s3c2410 ARM SoC")
Link: https://github.com/ClangBuiltLinux/linux/issues/1004
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c935deace ]
When the remote wakeup interrupt is triggered, lx_state is resumed from L2
to L0 state. But when the gadget resume is called, lx_state is still L2.
This prevents the resume callback to queue any request. Any attempt
to queue a request from resume callback will result in:
- "submit request only in active state" debug message to be issued
- dwc2_hsotg_ep_queue() returns -EAGAIN
Call the gadget resume routine after the core is in L0 state.
Fixes: f81f46e1f5 ("usb: dwc2: implement hibernation during bus suspend/resume")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d49292025f ]
The function ehci_mxc_drv_probe() does not perform sufficient error
checking after executing platform_get_irq(), thus fix it.
Fixes: 7e8d5cd93f ("USB: Add EHCI support for MX27 and MX31 based boards")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200513132647.5456-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b919e077cc ]
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 7d9e6f5aeb ("usb: host: ohci-sm501: init genalloc for local memory")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200506135625.106910-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d99087c2d ]
If dwc3 fails to issue START_TRANSFER/UPDATE_TRANSFER command, then we
should properly end an active transfer and give back all the started
requests. However if it's for an isoc endpoint, the failure maybe due to
bus-expiry status. In this case, don't give back the requests and wait
for the next retry.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb11ea56f3 ]
DWC3 must not issue CLEAR_STALL command to control endpoints. The
controller automatically clears the STALL when it receives the SETUP
token. Also, when the driver receives ClearFeature(halt_ep), DWC3 must
stop any active transfer from the endpoint and give back all the
requests to the function drivers.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c73bc5219 ]
The threaded interrupt handler may still be called after the
usb_gadget_disconnect is called, it causes the structures used
at interrupt handler was freed before it uses, eg the
usb_request. This issue usually occurs we remove the udc function
during the transfer. Below is the example when doing stress
test for android switch function, the EP0's request is freed
by .unbind (configfs_composite_unbind -> composite_dev_cleanup),
but the threaded handler accesses this request during handling
setup packet request.
In fact, there is no protection between unbind the udc
and udc interrupt handling, so we have to avoid the interrupt
handler is occurred or scheduled during the .unbind flow.
init: Sending signal 9 to service 'adbd' (pid 18077) process group...
android_work: did not send uevent (0 0 000000007bec2039)
libprocessgroup: Successfully killed process cgroup uid 0 pid 18077 in 6ms
init: Service 'adbd' (pid 18077) received signal 9
init: Sending signal 9 to service 'adbd' (pid 18077) process group...
libprocessgroup: Successfully killed process cgroup uid 0 pid 18077 in 0ms
init: processing action (init.svc.adbd=stopped) from (/init.usb.configfs.rc:14)
init: Received control message 'start' for 'adbd' from pid: 399 (/vendor/bin/hw/android.hardware.usb@1.
init: starting service 'adbd'...
read descriptors
read strings
Unable to handle kernel read from unreadable memory at virtual address 000000000000002a
android_work: sent uevent USB_STATE=CONNECTED
Mem abort info:
ESR = 0x96000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=00000000e97f1000
using random self ethernet address
[000000000000002a] pgd=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 232 Comm: irq/68-5b110000 Not tainted 5.4.24-06075-g94a6b52b5815 #92
Hardware name: Freescale i.MX8QXP MEK (DT)
pstate: 00400085 (nzcv daIf +PAN -UAO)
using random host ethernet address
pc : composite_setup+0x5c/0x1730
lr : android_setup+0xc0/0x148
sp : ffff80001349bba0
x29: ffff80001349bba0 x28: ffff00083a50da00
x27: ffff8000124e6000 x26: ffff800010177950
x25: 0000000000000040 x24: ffff000834e18010
x23: 0000000000000000 x22: 0000000000000000
x21: ffff00083a50da00 x20: ffff00082e75ec40
x19: 0000000000000000 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: 0000000000000001
x11: ffff80001180fb58 x10: 0000000000000040
x9 : ffff8000120fc980 x8 : 0000000000000000
x7 : ffff00083f98df50 x6 : 0000000000000100
x5 : 00000307e8978431 x4 : ffff800011386788
x3 : 0000000000000000 x2 : ffff800012342000
x1 : 0000000000000000 x0 : ffff800010c6d3a0
Call trace:
composite_setup+0x5c/0x1730
android_setup+0xc0/0x148
cdns3_ep0_delegate_req+0x64/0x90
cdns3_check_ep0_interrupt_proceed+0x384/0x738
cdns3_device_thread_irq_handler+0x124/0x6e0
cdns3_thread_irq+0x94/0xa0
irq_thread_fn+0x30/0xa0
irq_thread+0x150/0x248
kthread+0xfc/0x128
ret_from_fork+0x10/0x18
Code: 910e8000 f9400693 12001ed7 79400f79 (3940aa61)
---[ end trace c685db37f8773fba ]---
Kernel panic - not syncing: Fatal exception
SMP: stopping secondary CPUs
Kernel Offset: disabled
CPU features: 0x0002,20002008
Memory Limit: none
Rebooting in 5 seconds..
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The default 40ms is the minimum value according to BC 1.2 spec,
it works not well for Type-C port when connected with DCP charger.
Like this ticket described, the DCP charger will be recognized as
SDP. After increasing TVDPSRC_ON value to 240ms, the Type-C port could
work well with DCP charger.
imx8dxl mek, imx7ulp evk and imx8qxp mek are tested.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The TD_SIZE entry is 16 bit at TRB for HS/FS, it fixed the issue
if the request length is 16384 bytes for FS transfer, at this case,
the TD_SIZE is 0 at current code.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The Cadence device doesn't have abilities to send L1 resume by hardware,
so the software needs to send L1 resume at below situations:
- When the software is prepared to transfer
- When the bus is in L1 suspend
If the bus is not in L1 suspend, sending resume by software has no real
effect.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The 'tmode' is ctrl->wIndex, changing it as the real test
mode value for register assignment.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
commit 97fe809934 upstream.
If buffers are iterated over in the error case, the lower limits
for quirky devices must be heeded.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: Jean Rene Dawin <jdawin@math.uni-bielefeld.de>
Fixes: a4e7279cd1 ("cdc-acm: introduce a cool down")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200526124420.22160-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4befc121d upstream.
When copy_from_user() returns an error code, there
is a runtime PM usage counter imbalance.
Fix this by moving copy_from_user() to the beginning
of this function.
Fixes: 7b6c1b4c0e ("usb: musb: fix runtime PM in debugfs")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200525025049.3400-7-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f88a5ac39 upstream.
Commit 17539f2f4f ("usb: musb: fix enumeration after resume") replaced
musb_start() in musb_resume() to not override softconnect bit, but it
doesn't restart the session for host port which was done in musb_start().
The session could be disabled in musb_suspend(), which leads the host
port doesn't stay in host mode.
So let's start the session specifically for host port in musb_resume().
Fixes: 17539f2f4f ("usb: musb: fix enumeration after resume")
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200525025049.3400-3-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c404bf4aa9 upstream.
A subset of CH341 devices does not support all features, namely the
prescaler is limited to a reduced precision and there is no support for
sending a RS232 break condition. This patch adds a detection function
which will be extended to set quirk flags as they're implemented.
The author's affected device has an imprint of "340" on the
turquoise-colored plug, but not all such devices appear to be affected.
Signed-off-by: Michael Hanselmann <public@hansmi.ch>
Link: https://lore.kernel.org/r/1e1ae0da6082bb528a44ef323d4e1d3733d38858.1585697281.git.public@hansmi.ch
[ johan: use long type for quirks; rephrase and use port device for
messages; handle short reads; set quirk flags directly in
helper function ]
Cc: stable <stable@vger.kernel.org> # 5.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 986c1748c8 upstream.
usb_wwan_indat_callback() shouldn't resubmit rx urb if the previous urb
status is a fatal error. Or the usb controller would keep processing the
new urbs then run into interrupt storm, and has no chance to recover.
Fixes: 6c1ee66a0b ("USB-Serial: Fix error handling of usb_wwan")
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3429444abd upstream.
Add support for Dell Wireless 5816e Download Mode (AKA boot & hold mode /
QDL download mode) to drivers/usb/serial/qcserial.c
This is required to update device firmware.
Signed-off-by: Matt Jolly <Kangie@footclan.ninja>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d13cce7579 ]
Fix the following cppcheck warnings:
drivers/usb/gadget/legacy/inode.c:1364:8: style: Redundant initialization for 'value'. The initialized value is overwritten$
value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1331:15: note: value is initialized
int value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1364:8: note: value is overwritten
value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1817:8: style: Redundant initialization for 'value'. The initialized value is overwritten$
value = -EINVAL;
^
drivers/usb/gadget/legacy/inode.c:1787:18: note: value is initialized
ssize_t value = len, length = len;
^
drivers/usb/gadget/legacy/inode.c:1817:8: note: value is overwritten
value = -EINVAL;
^
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f058764d19 ]
A call to 'regulator_get()' is hidden in 'twl6030_usb_ldo_init()'. A
corresponding put must be performed in the error handling path, as
already done in the remove function.
While at it, also move a 'free_irq()' call in the error handling path in
order to be consistent.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 066c095934 ]
Intel Merrifield provides a DR support via PMIC which has its own
extcon driver.
Add a property string to link to that driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac854131d9 ]
The syzbot fuzzer found a race between URB submission to endpoint 0
and device reset. Namely, during the reset we call usb_ep0_reinit()
because the characteristics of ep0 may have changed (if the reset
follows a firmware update, for example). While usb_ep0_reinit() is
running there is a brief period during which the pointers stored in
udev->ep_in[0] and udev->ep_out[0] are set to NULL, and if an URB is
submitted to ep0 during that period, usb_urb_ep_type_check() will
report it as a driver bug. In the absence of those pointers, the
routine thinks that the endpoint doesn't exist. The log message looks
like this:
------------[ cut here ]------------
usb 2-1: BOGUS urb xfer, pipe 2 != type 2
WARNING: CPU: 0 PID: 9241 at drivers/usb/core/urb.c:478
usb_submit_urb+0x1188/0x1460 drivers/usb/core/urb.c:478
Now, although submitting an URB while the device is being reset is a
questionable thing to do, it shouldn't count as a driver bug as severe
as submitting an URB for an endpoint that doesn't exist. Indeed,
endpoint 0 always exists, even while the device is in its unconfigured
state.
To prevent these misleading driver bug reports, this patch updates
usb_disable_endpoint() to avoid clearing the ep_in[] and ep_out[]
pointers when the endpoint being disabled is ep0. There's no danger
of leaving a stale pointer in place, because the usb_host_endpoint
structure being pointed to is stored permanently in udev->ep0; it
doesn't get deallocated until the entire usb_device structure does.
Reported-and-tested-by: syzbot+db339689b2101f6f6071@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2005011558590.903-100000@netrider.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e8f7f9e349 upstream.
If 'usb_otg_descriptor_alloc()' fails, we must return a
negative error code -ENOMEM, not 0.
Fixes: ab6796ae98 ("usb: gadget: cdc2: allocate and init otg descriptor by otg capabilities")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e27d4b30b7 upstream.
If 'usb_otg_descriptor_alloc()' fails, we must return a
negative error code -ENOMEM, not 0.
Fixes: 1156e91dd7 ("usb: gadget: ncm: allocate and init otg descriptor by otg capabilities")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19b94c1f9c upstream.
If 'usb_otg_descriptor_alloc()' fails, we must return an error code, not 0.
Fixes: 56023ce0fd ("usb: gadget: audio: allocate and init otg descriptor by otg capabilities")
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccaef7e6e3 upstream.
'dev' is allocated in 'net2272_probe_init()'. It must be freed in the error
handling path, as already done in the remove function (i.e.
'net2272_plat_remove()')
Fixes: 90fccb529d ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00e21763f2 upstream.
The check for the HWO flag in dwc3_gadget_ep_reclaim_trb_sg()
causes us to break out of the loop before we call
dwc3_gadget_ep_reclaim_completed_trb(), which is what likely
should be clearing the HWO flag.
This can cause odd behavior where we never reclaim all the trbs
in the sg list, so we never call giveback on a usb req, and that
will causes transfer stalls.
This effectively resovles the adb stalls seen on HiKey960
after userland changes started only using AIO in adbd.
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Josh Gao <jmgao@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org #4.20+
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c6f8cb92c upstream.
On platforms with IOMMU enabled, multiple SGs can be coalesced into one
by the IOMMU driver. In that case the SG list processing as part of the
completion of a urb on a bulk endpoint can result into a NULL pointer
dereference with the below stack dump.
<6> Unable to handle kernel NULL pointer dereference at virtual address 0000000c
<6> pgd = c0004000
<6> [0000000c] *pgd=00000000
<6> Internal error: Oops: 5 [#1] PREEMPT SMP ARM
<2> PC is at xhci_queue_bulk_tx+0x454/0x80c
<2> LR is at xhci_queue_bulk_tx+0x44c/0x80c
<2> pc : [<c08907c4>] lr : [<c08907bc>] psr: 000000d3
<2> sp : ca337c80 ip : 00000000 fp : ffffffff
<2> r10: 00000000 r9 : 50037000 r8 : 00004000
<2> r7 : 00000000 r6 : 00004000 r5 : 00000000 r4 : 00000000
<2> r3 : 00000000 r2 : 00000082 r1 : c2c1a200 r0 : 00000000
<2> Flags: nzcv IRQs off FIQs off Mode SVC_32 ISA ARM Segment none
<2> Control: 10c0383d Table: b412c06a DAC: 00000051
<6> Process usb-storage (pid: 5961, stack limit = 0xca336210)
<snip>
<2> [<c08907c4>] (xhci_queue_bulk_tx)
<2> [<c0881b3c>] (xhci_urb_enqueue)
<2> [<c0831068>] (usb_hcd_submit_urb)
<2> [<c08350b4>] (usb_sg_wait)
<2> [<c089f384>] (usb_stor_bulk_transfer_sglist)
<2> [<c089f2c0>] (usb_stor_bulk_srb)
<2> [<c089fe38>] (usb_stor_Bulk_transport)
<2> [<c089f468>] (usb_stor_invoke_transport)
<2> [<c08a11b4>] (usb_stor_control_thread)
<2> [<c014a534>] (kthread)
The above NULL pointer dereference is the result of block_len and the
sent_len set to zero after the first SG of the list when IOMMU driver
is enabled. Because of this the loop of processing the SGs has run
more than num_sgs which resulted in a sg_next on the last SG of the
list which has SG_END set.
Fix this by check for the sg before any attributes of the sg are
accessed.
[modified reason for null pointer dereference in commit message subject -Mathias]
Fixes: f9c589e142 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Cc: stable@vger.kernel.org
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200514110432.25564-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15753588bc upstream.
FuzzUSB (a variant of syzkaller) found an illegal array access
using an incorrect index while binding a gadget with UDC.
Reference: https://www.spinics.net/lists/linux-usb/msg194331.html
This bug occurs when a size variable used for a buffer
is misused to access its strcpy-ed buffer.
Given a buffer along with its size variable (taken from user input),
from which, a new buffer is created using kstrdup().
Due to the original buffer containing 0 value in the middle,
the size of the kstrdup-ed buffer becomes smaller than that of the original.
So accessing the kstrdup-ed buffer with the same size variable
triggers memory access violation.
The fix makes sure no zero value in the buffer,
by comparing the strlen() of the orignal buffer with the size variable,
so that the access to the kstrdup-ed buffer is safe.
BUG: KASAN: slab-out-of-bounds in gadget_dev_desc_UDC_store+0x1ba/0x200
drivers/usb/gadget/configfs.c:266
Read of size 1 at addr ffff88806a55dd7e by task syz-executor.0/17208
CPU: 2 PID: 17208 Comm: syz-executor.0 Not tainted 5.6.8 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xce/0x128 lib/dump_stack.c:118
print_address_description.constprop.4+0x21/0x3c0 mm/kasan/report.c:374
__kasan_report+0x131/0x1b0 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:641
__asan_report_load1_noabort+0x14/0x20 mm/kasan/generic_report.c:132
gadget_dev_desc_UDC_store+0x1ba/0x200 drivers/usb/gadget/configfs.c:266
flush_write_buffer fs/configfs/file.c:251 [inline]
configfs_write_file+0x2f1/0x4c0 fs/configfs/file.c:283
__vfs_write+0x85/0x110 fs/read_write.c:494
vfs_write+0x1cd/0x510 fs/read_write.c:558
ksys_write+0x18a/0x220 fs/read_write.c:611
__do_sys_write fs/read_write.c:623 [inline]
__se_sys_write fs/read_write.c:620 [inline]
__x64_sys_write+0x73/0xb0 fs/read_write.c:620
do_syscall_64+0x9e/0x510 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Kyungtae Kim <kt0755@gmail.com>
Reported-and-tested-by: Kyungtae Kim <kt0755@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200510054326.GA19198@pizza01
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0e710a7de upstream.
In commit 2bef9aed6f ("usb: usbfs: correct kernel->user page attribute
mismatch") we switched from always calling remap_pfn_range() to call
dma_mmap_coherent() to handle issues with systems with non-coherent USB host
controller drivers. Unfortunatly, as syzbot quickly told us, not all the world
is host controllers with DMA support, so we need to check what host controller
we are attempting to talk to before doing this type of allocation.
Thanks to Christoph for the quick idea of how to fix this.
Fixes: 2bef9aed6f ("usb: usbfs: correct kernel->user page attribute mismatch")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+353be47c9ce21b68b7ed@syzkaller.appspotmail.com
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20200514112711.1858252-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bef9aed6f upstream.
On some architectures (e.g. arm64) requests for
IO coherent memory may use non-cachable attributes if
the relevant device isn't cache coherent. If these
pages are then remapped into userspace as cacheable,
they may not be coherent with the non-cacheable mappings.
In particular this happens with libusb, when it attempts
to create zero-copy buffers for use by rtl-sdr
(https://github.com/osmocom/rtl-sdr/). On low end arm
devices with non-coherent USB ports, the application will
be unexpectedly killed, while continuing to work fine on
arm machines with coherent USB controllers.
This bug has been discovered/reported a few times over
the last few years. In the case of rtl-sdr a compile time
option to enable/disable zero copy was implemented to
work around it.
Rather than relaying on application specific workarounds,
dma_mmap_coherent() can be used instead of remap_pfn_range().
The page cache/etc attributes will then be correctly set in
userspace to match the kernel mapping.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200504201348.1183246-1-jeremy.linton@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9b3c610a0 upstream.
We must not process packets shorter than a packet ID
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-and-tested-by: syzbot+d29e9263e13ce0b9f4fd@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91edf63d50 upstream.
Currently we check to make sure there is no error state on the extcon
handle for VBUS when writing to the HS_PHY_GENCONFIG_2 register. When using
the USB role-switch API we still need to write to this register absent an
extcon handle.
This patch makes the appropriate update to ensure the write happens if
role-switching is true.
Fixes: 05559f10ed ("usb: chipidea: add role switch class support")
Cc: stable <stable@vger.kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200507004918.25975-2-peter.chen@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is better to re-init request list for EP0 when the EP0 begins to
uses.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The new usb_gadget_disconnect API includes both calling class
driver's disconnect and calling .pullup at udc driver, so we
could simply your udc driver handling.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
We do not want to handle any interrupts after usb_gadget_disconnect
is called.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Below is the recommendation from Cadence designer:
Using this bit to be sure that PHY clock is keeping up in active
state. It's good to keep Fast Access bit enabled as long as there
is any access to USB register.
It is used to fix the potential ARM core hang when visit controller
register after DEVDS is set.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The threaded interrupt handler may still be called after the
usb_gadget_disconnect is called, it causes the structures used
at interrupt handler was freed before it uses, eg the
usb_request. This issue usually occurs we remove the udc function
during the transfer. Below is the example when doing stress
test for android switch function, the EP0's request is freed
by .unbind (configfs_composite_unbind -> composite_dev_cleanup),
but the threaded handler accesses this request during handling
setup packet request.
In fact, there is no protection between unbind the udc
and udc interrupt handling, so we have to avoid the interrupt
handler is occurred or scheduled during the .unbind flow.
init: Sending signal 9 to service 'adbd' (pid 18077) process group...
android_work: did not send uevent (0 0 000000007bec2039)
libprocessgroup: Successfully killed process cgroup uid 0 pid 18077 in 6ms
init: Service 'adbd' (pid 18077) received signal 9
init: Sending signal 9 to service 'adbd' (pid 18077) process group...
libprocessgroup: Successfully killed process cgroup uid 0 pid 18077 in 0ms
init: processing action (init.svc.adbd=stopped) from (/init.usb.configfs.rc:14)
init: Received control message 'start' for 'adbd' from pid: 399 (/vendor/bin/hw/android.hardware.usb@1.
init: starting service 'adbd'...
read descriptors
read strings
Unable to handle kernel read from unreadable memory at virtual address 000000000000002a
android_work: sent uevent USB_STATE=CONNECTED
Mem abort info:
ESR = 0x96000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=00000000e97f1000
using random self ethernet address
[000000000000002a] pgd=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 232 Comm: irq/68-5b110000 Not tainted 5.4.24-06075-g94a6b52b5815 #92
Hardware name: Freescale i.MX8QXP MEK (DT)
pstate: 00400085 (nzcv daIf +PAN -UAO)
using random host ethernet address
pc : composite_setup+0x5c/0x1730
lr : android_setup+0xc0/0x148
sp : ffff80001349bba0
x29: ffff80001349bba0 x28: ffff00083a50da00
x27: ffff8000124e6000 x26: ffff800010177950
x25: 0000000000000040 x24: ffff000834e18010
x23: 0000000000000000 x22: 0000000000000000
x21: ffff00083a50da00 x20: ffff00082e75ec40
x19: 0000000000000000 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: 0000000000000001
x11: ffff80001180fb58 x10: 0000000000000040
x9 : ffff8000120fc980 x8 : 0000000000000000
x7 : ffff00083f98df50 x6 : 0000000000000100
x5 : 00000307e8978431 x4 : ffff800011386788
x3 : 0000000000000000 x2 : ffff800012342000
x1 : 0000000000000000 x0 : ffff800010c6d3a0
Call trace:
composite_setup+0x5c/0x1730
android_setup+0xc0/0x148
cdns3_ep0_delegate_req+0x64/0x90
cdns3_check_ep0_interrupt_proceed+0x384/0x738
cdns3_device_thread_irq_handler+0x124/0x6e0
cdns3_thread_irq+0x94/0xa0
irq_thread_fn+0x30/0xa0
irq_thread+0x150/0x248
kthread+0xfc/0x128
ret_from_fork+0x10/0x18
Code: 910e8000 f9400693 12001ed7 79400f79 (3940aa61)
---[ end trace c685db37f8773fba ]---
Kernel panic - not syncing: Fatal exception
SMP: stopping secondary CPUs
Kernel Offset: disabled
CPU features: 0x0002,20002008
Memory Limit: none
Rebooting in 5 seconds..
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
[ Upstream commit d94ea53198 ]
Currently the calculation of max packet size limit for IN endpoints is
too restrictive. This prevents a matching of a capable hardware endpoint
during configuration. Below is the minimum recommended HW configuration
to support a particular endpoint setup from the databook:
For OUT endpoints, the databook recommended the minimum RxFIFO size to
be at least 3x MaxPacketSize + 3x setup packets size (8 bytes each) +
clock crossing margin (16 bytes).
For IN endpoints, the databook recommended the minimum TxFIFO size to be
at least 3x MaxPacketSize for endpoints that support burst. If the
endpoint doesn't support burst or when the device is operating in USB
2.0 mode, a minimum TxFIFO size of 2x MaxPacketSize is recommended.
Base on these recommendations, we can calculate the MaxPacketSize limit
of each endpoint. This patch revises the IN endpoint MaxPacketSize limit
and also sets the MaxPacketSize limit for OUT endpoints.
Reference: Databook 3.30a section 3.2.2 and 3.2.3
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
EP command will use suspend_clk(32K) if the SS PHY is at P3,
this slow clock makes EP command need more time to complete,
1000 times register read is not enough in this case, will
generate timeout like below:
dwc3_gadget_ep_cmd: ep0out: cmd 'Set Endpoint Configuration' [401]
params 00001000 00000500 00000000 --> status: Timed Out
Success case takes about 400us to complete, see below trace
(44.286278 - 44.285897 = 0.000381s):
configfs_acm.sh-822 [000] d..1 44.285896: dwc3_writel:
addr 000000006d59aae1 value 00000401
configfs_acm.sh-822 [000] d..1 44.285897: dwc3_readl:
addr 000000006d59aae1 value 00000401
... ...
configfs_acm.sh-822 [000] d..1 44.286278: dwc3_readl:
addr 000000006d59aae1 value 00000001
configfs_acm.sh-822 [000] d..1 44.286279: dwc3_gadget_ep_cmd:
ep0out: cmd 'Set Endpoint Configuration' [401]
params 00001000 00000500 00000000 --> status: Successful
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Since the typec port data role is separated from power role,
so check the port data capability when setting data role.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/1581666828-2063-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 6ecc632d4b)
commit 12b94da411 upstream.
A DMA transfer can be in progress while vbus is lost due to a cable
disconnect. For endpoints that use DMA, this condition can lead to
peripheral hang. The patch ensures that endpoints are disabled before
the clocks are stopped to prevent this issue.
Fixes: a64ef71ddc ("usb: gadget: atmel_usba_udc: condition clocks to vbus state")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09b04abb70 upstream.
When building with Clang + -Wtautological-pointer-compare:
drivers/usb/gadget/udc/bdc/bdc_ep.c:543:28: warning: comparison of
address of 'req->queue' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (req == NULL || &req->queue == NULL || &req->usb_req == NULL)
~~~~~^~~~~ ~~~~
drivers/usb/gadget/udc/bdc/bdc_ep.c:543:51: warning: comparison of
address of 'req->usb_req' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (req == NULL || &req->queue == NULL || &req->usb_req == NULL)
~~~~~^~~~~~~ ~~~~
2 warnings generated.
As it notes, these statements will always evaluate to false so remove
them.
Fixes: efed421a94 ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC")
Link: https://github.com/ClangBuiltLinux/linux/issues/749
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0550cd20e upstream.
The controller always supports link recovery for device in SS and SSP.
Remove the speed limit check. Also, when the device is in RESUME or
RESET state, it means the controller received the resume/reset request.
The driver must send the link recovery to acknowledge the request. They
are valid states for the driver to send link recovery.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Fixes: ee5cd41c91 ("usb: dwc3: Update speed checks for SuperSpeedPlus")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f97250c21 upstream.
The default control endpoint ep0 can return a STALL indicating the
device does not support the control transfer requests. This is called
a protocol stall and does not halt the endpoint.
xHC behaves a bit different. Its internal endpoint state will always
be halted on any stall, even if the device side of the endpiont is not
halted. So we do need to issue the reset endpoint command to clear the
xHC host intenal endpoint halt state, but should not request the HS hub
to clear the TT buffer unless device side of endpoint is halted.
Clearing the hub TT buffer at protocol stall caused ep0 to become
unresponsive for some FS/LS devices behind HS hubs, and class drivers
failed to set the interface due to timeout:
usb 1-2.1: 1:1: usb_set_interface failed (-110)
Fixes: ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
Cc: <stable@vger.kernel.org> # v5.3
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9fb08d617 upstream.
Suspending the bus and host controller while a port is in a over-current
condition may halt the host.
Also keep the roothub running if over-current is active.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93ceaa808e upstream.
If a class driver cancels its only URB then the endpoint ring buffer will
appear empty to the xhci driver. xHC hardware may still process cached
TRBs, and complete with a STALL, halting the endpoint.
This halted endpoint was not handled correctly by xhci driver as events on
empty rings were all assumed to be spurious events.
xhci driver refused to restart the ring with EP_HALTED flag set, so class
driver was never informed the endpoint halted even if it queued new URBs.
The host side of the endpoint needs to be reset, and dequeue pointer should
be moved in order to clear the cached TRBs and resetart the endpoint.
Small adjustments in finding the new dequeue pointer are needed to support
the case of stall on an empty ring and unknown current TD.
Cc: <stable@vger.kernel.org>
cc: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c2e54fbf1 upstream.
For userspace functions using OS Descriptors, if a function also supplies
Extended Property descriptors currently the counts and lengths stored in
the ms_os_descs_ext_prop_{count,name_len,data_len} variables are not
getting reset to 0 during an unbind or when the epfiles are closed. If
the same function is re-bound and the descriptors are re-written, this
results in those count/length variables to monotonically increase
causing the VLA allocation in _ffs_func_bind() to grow larger and larger
at each bind/unbind cycle and eventually fail to allocate.
Fix this by clearing the ms_os_descs_ext_prop count & lengths to 0 in
ffs_data_reset().
Fixes: f0175ab519 ("usb: gadget: f_fs: OS descriptors support")
Cc: stable@vger.kernel.org
Signed-off-by: Udipto Goswami <ugoswami@codeaurora.org>
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Link: https://lore.kernel.org/r/20200402044521.9312-1-sallenki@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49e0590e3a upstream.
A request may not be completed because not all the TRBs are prepared for
it. This happens when we run out of available TRBs. When some TRBs are
completed, the driver needs to prepare the rest of the TRBs for the
request. The check dwc3_gadget_ep_request_completed() shouldn't be
checking the amount of data received but rather the number of pending
TRBs. Revise this request completion check.
Cc: stable@vger.kernel.org
Fixes: e0c42ce590 ("usb: dwc3: gadget: simplify IOC handling")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6cc6093a7 upstream.
A SCSI error handler and block runtime PM must not allocate
memory with GFP_KERNEL. Furthermore they must not wait for
tasks allocating memory with GFP_KERNEL.
That means that they cannot share a workqueue with arbitrary tasks.
Fix this for UAS using a private workqueue.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: f9dc024a2d ("uas: pre_reset and suspend: Fix a few races")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200415141750.811-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5963dec98d upstream.
Once a device is gone, the internal state does not matter anymore.
There is no need to spam the logs.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 326349f824 ("uas: add dead request list")
Link: https://lore.kernel.org/r/20200415141750.811-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4e7279cd1 upstream.
Immediate submission in case of a babbling device can lead
to a busy loop. Introducing a delayed work.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Jonas Karlsson <jonas.karlsson@actia.se>
Link: https://lore.kernel.org/r/20200415151358.32664-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0afccd7601 upstream.
Suspend increments a counter, then kills the URBs,
then kills the scheduled work. The scheduled work, however,
may reschedule the URBs. Fix this by having the work
check the counter.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Jonas Karlsson <jonas.karlsson@actia.se>
Link: https://lore.kernel.org/r/20200415151358.32664-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94f9c8c3c4 upstream.
Cyril Roelandt reports that his JMicron JMS566 USB-SATA bridge fails
to handle WRITE commands with the FUA bit set, even though it claims
to support FUA. (Oddly enough, a later version of the same bridge,
version 2.03 as opposed to 1.14, doesn't claim to support FUA. Also
oddly, the bridge _does_ support FUA when using the UAS transport
instead of the Bulk-Only transport -- but this device was blacklisted
for uas in commit bc3bdb12bb ("usb-storage: Disable UAS on JMicron
SATA enclosure") for apparently unrelated reasons.)
This patch adds a usb-storage unusual_devs entry with the BROKEN_FUA
flag. This allows the bridge to work properly with usb-storage.
Reported-and-tested-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221613110.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3155f4f408 upstream.
Commit bd0e6c9614 ("usb: hub: try old enumeration scheme first for
high speed devices") changed the way the hub driver enumerates
high-speed devices. Instead of using the "new" enumeration scheme
first and switching to the "old" scheme if that doesn't work, we start
with the "old" scheme. In theory this is better because the "old"
scheme is slightly faster -- it involves resetting the device only
once instead of twice.
However, for a long time Windows used only the "new" scheme. Zeng Tao
said that Windows 8 and later use the "old" scheme for high-speed
devices, but apparently there are some devices that don't like it.
William Bader reports that the Ricoh webcam built into his Sony Vaio
laptop not only doesn't enumerate under the "old" scheme, it gets hung
up so badly that it won't then enumerate under the "new" scheme! Only
a cold reset will fix it.
Therefore we will revert the commit and go back to trying the "new"
scheme first for high-speed devices.
Reported-and-tested-by: William Bader <williambader@hotmail.com>
Ref: https://bugzilla.kernel.org/show_bug.cgi?id=207219
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: bd0e6c9614 ("usb: hub: try old enumeration scheme first for high speed devices")
CC: Zeng Tao <prime.zeng@hisilicon.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221611230.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f952e2629 upstream.
Commit 8099f58f1e ("USB: hub: Don't record a connect-change event
during reset-resume") wasn't very well conceived. The problem it
tried to fix was that if a connect-change event occurred while the
system was asleep (such as a device disconnecting itself from the bus
when it is suspended and then reconnecting when it resumes)
requiring a reset-resume during the system wakeup transition, the hub
port's change_bit entry would remain set afterward. This would cause
the hub driver to believe another connect-change event had occurred
after the reset-resume, which was wrong and would lead the driver to
send unnecessary requests to the device (which could interfere with a
firmware update).
The commit tried to fix this by not setting the change_bit during the
wakeup. But this was the wrong thing to do; it means that when a
device is unplugged while the system is asleep, the hub driver doesn't
realize anything has happened: The change_bit flag which would tell it
to handle the disconnect event is clear.
The commit needs to be reverted and the problem fixed in a different
way. Fortunately an alternative solution was noted in the commit's
Changelog: We can continue to set the change_bit entry in
hub_activate() but then clear it when a reset-resume occurs. That way
the the hub driver will see the change_bit when a device is
disconnected but won't see it when the device is still present.
That's what this patch does.
Reported-and-tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8099f58f1e ("USB: hub: Don't record a connect-change event during reset-resume")
Tested-by: Paul Zimmerman <pauldzim@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221602480.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 056ad39ee9 upstream.
FuzzUSB (a variant of syzkaller) found a free-while-still-in-use bug
in the USB scatter-gather library:
BUG: KASAN: use-after-free in atomic_read
include/asm-generic/atomic-instrumented.h:26 [inline]
BUG: KASAN: use-after-free in usb_hcd_unlink_urb+0x5f/0x170
drivers/usb/core/hcd.c:1607
Read of size 4 at addr ffff888065379610 by task kworker/u4:1/27
CPU: 1 PID: 27 Comm: kworker/u4:1 Not tainted 5.5.11 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.10.2-1ubuntu1 04/01/2014
Workqueue: scsi_tmf_2 scmd_eh_abort_handler
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xce/0x128 lib/dump_stack.c:118
print_address_description.constprop.4+0x21/0x3c0 mm/kasan/report.c:374
__kasan_report+0x153/0x1cb mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:639
check_memory_region_inline mm/kasan/generic.c:185 [inline]
check_memory_region+0x152/0x1b0 mm/kasan/generic.c:192
__kasan_check_read+0x11/0x20 mm/kasan/common.c:95
atomic_read include/asm-generic/atomic-instrumented.h:26 [inline]
usb_hcd_unlink_urb+0x5f/0x170 drivers/usb/core/hcd.c:1607
usb_unlink_urb+0x72/0xb0 drivers/usb/core/urb.c:657
usb_sg_cancel+0x14e/0x290 drivers/usb/core/message.c:602
usb_stor_stop_transport+0x5e/0xa0 drivers/usb/storage/transport.c:937
This bug occurs when cancellation of the S-G transfer races with
transfer completion. When that happens, usb_sg_cancel() may continue
to access the transfer's URBs after usb_sg_wait() has freed them.
The bug is caused by the fact that usb_sg_cancel() does not take any
sort of reference to the transfer, and so there is nothing to prevent
the URBs from being deallocated while the routine is trying to use
them. The fix is to take such a reference by incrementing the
transfer's io->count field while the cancellation is in progres and
decrementing it afterward. The transfer's URBs are not deallocated
until io->complete is triggered, which happens when io->count reaches
zero.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Kyungtae Kim <kt0755@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2003281615140.14837-100000@netrider.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dbdb53d72 upstream.
This fixes a bug that causes the USB3 early console to freeze after
printing a single line on AMD machines because it can't parse the
Transfer TRB properly.
The spec at
https://www.intel.com/content/dam/www/public/us/en/documents/technical-specifications/extensible-host-controler-interface-usb-xhci.pdf
says in section "4.5.1 Device Context Index" that the Context Index,
also known as Endpoint ID according to
section "1.6 Terms and Abbreviations", is normally computed as
`DCI = (Endpoint Number * 2) + Direction`, which matches the current
definitions of XDBC_EPID_OUT and XDBC_EPID_IN.
However, the numbering in a Debug Capability Context data structure is
supposed to be different:
Section "7.6.3.2 Endpoint Contexts and Transfer Rings" explains that a
Debug Capability Context data structure has the endpoints mapped to indices
0 and 1.
Change XDBC_EPID_OUT/XDBC_EPID_IN to the spec-compliant values, add
XDBC_EPID_OUT_INTEL/XDBC_EPID_IN_INTEL with Intel's incorrect values, and
let xdbc_handle_tx_event() handle both.
I have verified that with this patch applied, the USB3 early console works
on both an Intel and an AMD machine.
Fixes: aeb9dd1de9 ("usb/early: Add driver for xhci debug capability")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20200401074619.8024-1-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be34a5854b upstream.
The Corsair K70 RGB RAPIDFIRE needs the USB_QUIRK_DELAY_INIT and
USB_QUIRK_DELAY_CTRL_MSG to function or it will randomly not
respond on boot, just like other Corsair keyboards
Signed-off-by: Jonathan Cox <jonathan@jdcox.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200410212427.2886-1-jonathan@jdcox.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2df7405f79 upstream.
Change a bunch of arguments of wrapper functions which pass signed
integer to an unsigned integer which might cause undefined behaviors
when sign integer overflow.
Signed-off-by: Changming Liu <liu.changm@northeastern.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/BL0PR06MB45482D71EA822D75A0E60A2EE5D50@BL0PR06MB4548.namprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ceca49382a ]
Depending on the current link state the steps to resume the link to U0
varies. The normal case when a port is suspended (U3) we set the link
to U0 and wait for a port event when U3exit completed and port moved to
U0.
If the port is in U1/U2, then no event is issued, just set link to U0
If port is in Resume or Recovery state then the device has already
initiated resume, and this host initiated resume is racing against it.
Port event handler for device initiated resume will set link to U0,
just wait for the port to reach U0 before returning.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0200b9f790 ]
Like U3 case, xHCI spec doesn't specify the upper bound of U0 transition
time. The 20ms is not enough for some devices.
Intead of polling PLS or PLC, we can facilitate the port change event to
know that the link transits to U0 is completed.
While at it, also separate U0 and U3 case to make the code cleaner.
[variable rename to u3exit, and skip completion for usb2 ports -Mathias ]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb002726fa ]
The xHCI spec doesn't specify the upper bound of U3 transition time. For
some devices 20ms is not enough, so we need to make sure the link state
is in U3 before further actions.
I've tried to use U3 Entry Capability by setting U3 Entry Enable in
config register, however the port change event for U3 transition
interrupts the system suspend process.
For now let's use the less ideal method by polling PLS.
[use usleep_range(), and shorten the delay time while polling -Mathias]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9f952e2629 upstream.
Commit 8099f58f1e ("USB: hub: Don't record a connect-change event
during reset-resume") wasn't very well conceived. The problem it
tried to fix was that if a connect-change event occurred while the
system was asleep (such as a device disconnecting itself from the bus
when it is suspended and then reconnecting when it resumes)
requiring a reset-resume during the system wakeup transition, the hub
port's change_bit entry would remain set afterward. This would cause
the hub driver to believe another connect-change event had occurred
after the reset-resume, which was wrong and would lead the driver to
send unnecessary requests to the device (which could interfere with a
firmware update).
The commit tried to fix this by not setting the change_bit during the
wakeup. But this was the wrong thing to do; it means that when a
device is unplugged while the system is asleep, the hub driver doesn't
realize anything has happened: The change_bit flag which would tell it
to handle the disconnect event is clear.
The commit needs to be reverted and the problem fixed in a different
way. Fortunately an alternative solution was noted in the commit's
Changelog: We can continue to set the change_bit entry in
hub_activate() but then clear it when a reset-resume occurs. That way
the the hub driver will see the change_bit when a device is
disconnected but won't see it when the device is still present.
That's what this patch does.
Reported-and-tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8099f58f1e ("USB: hub: Don't record a connect-change event during reset-resume")
Tested-by: Paul Zimmerman <pauldzim@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Flore.kernel.org%2Fr%2FPine.LNX.4.44L0.2004221602480.11262-100000%40iolanthe.rowland.org&data=02%7C01%7Cpeter.chen%40nxp.com%7C0c4a073d13d44cd9bb3a08d7eba40fdd%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C637236962191385194&sdata=gGE2I8VS%2BT2%2BrssNXoPaUKtBIk7WgnVMka7KhiGpWLA%3D&reserved=0
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cdns3_transfer_completed, it uses is_short to judge if current
request is short transfer to calculate req->actual correctly, but
is_short variable may for previous transfer, it causes req->actual
calculation wrong for current transfer. Eg, the previous transfer is
non-short tranfer, and the current one is short transfer, the req->actual
will accumulate the non-transfered TRB's length.
In fact, below condition already stands for short trasnfer for scatter
list:
if (priv_req->num_of_trb > 1 &&
le32_to_cpu(trb->control) & TRB_SMM)
So we could (need) to delete the parameter 'is_short'
Reviewed-by: Jun Li <jun.li@nxp.com>
Reported-by: Faqiang Zhu <faqiang.zhu@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
For each request, it needs to clear transfer_end, otherwise,
the second transfer's actual transfer length will not
report to class driver if the first transfer is short and both
the two transfers are handled in the same threaded irq handler.
Reviewed-by: Jun Li <jun.li@nxp.com>
Reported-by: Faqiang Zhu <faqiang.zhu@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
commit a114c4ca64 upstream.
We track END_TRANSFER command completion. Don't clear transfer
started/ended flag prematurely. Otherwise, we'd run into the problem
with restarting transfer before END_TRANSFER command finishes.
Fixes: 6d8a019614 ("usb: dwc3: gadget: check for Missed Isoc from event status")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e5caf4fa8 upstream.
Different configuration/condition may draw different power. Inform the
controller driver of the change so it can respond properly (e.g.
GET_STATUS request). This fixes an issue with setting MaxPower from
configfs. The composite driver doesn't check this value when setting
self-powered.
Cc: stable@vger.kernel.org
Fixes: 88af8bbe4e ("usb: gadget: the start of the configfs interface")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f63ec55ff9 upstream.
In AIO case, the request is freed up if ep_queue fails.
However, io_data->req still has the reference to this freed
request. In the case of this failure if there is aio_cancel
call on this io_data it will lead to an invalid dequeue
operation and a potential use after free issue.
Fix this by setting the io_data->req to NULL when the request
is freed as part of queue failure.
Fixes: 2e4c7553cd ("usb: gadget: f_fs: add aio support")
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
CC: stable <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200326115620.12571-1-sallenki@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7ba6b09fda ]
In certain circumstances, the XHCI SuperSpeed instance in park mode
can fail to recover, thus on Amlogic G12A/G12B/SM1 SoCs when there is high
load on the single XHCI SuperSpeed instance, the controller can crash like:
xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
xhci-hcd xhci-hcd.0.auto: Host halt failed, -110
xhci-hcd xhci-hcd.0.auto: xHCI host controller not responding, assume dead
xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
hub 2-1.1:1.0: hub_ext_port_status failed (err = -22)
xhci-hcd xhci-hcd.0.auto: HC died; cleaning up
usb 2-1.1-port1: cannot reset (err = -22)
Setting the PARKMODE_DISABLE_SS bit in the DWC3_USB3_GUCTL1 mitigates
the issue. The bit is described as :
"When this bit is set to '1' all SS bus instances in park mode are disabled"
Synopsys explains:
The GUCTL1.PARKMODE_DISABLE_SS is only available in
dwc_usb3 controller running in host mode.
This should not be set for other IPs.
This can be disabled by default based on IP, but I recommend to have a
property to enable this feature for devices that need this.
CC: Dongjin Kim <tobetter@gmail.com>
Cc: Jianxin Pan <jianxin.pan@amlogic.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Reported-by: Tim <elatllat@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72ae194704 ]
Bail out early if the xHC host needs to be reset at resume
but driver can't access xHC PCI registers.
If xhci driver already fails to reset the controller then there
is no point in attempting to free, re-initialize, re-allocate and
re-start the host. If failure to access the host is detected later,
failing the resume, xhci interrupts will be double freed
when remove is called.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2dedea035a upstream.
When skipping TRBs, we need to account for wrapping around the ring
buffer and not modifying some invalid TRBs. Without this fix, dwc3 won't
be able to check for available TRBs.
Cc: stable <stable@vger.kernel.org>
Fixes: 7746a8dfb3 ("usb: dwc3: gadget: extract dwc3_gadget_ep_skip_trbs()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need request high bus for USB data transfer, add it in runtime
PM.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
commit 52974d94a2 upstream.
When handling a PIO bulk transfer with highmem buffer, a temporary
mapping is assigned to urb->transfer_buffer. After the transfer is
complete, an invalid address is left behind in this pointer. This is
not ordinarily a problem since nothing touches that buffer before the
urb is released. However, when usbmon is active, usbmon_urb_complete()
calls (indirectly) mon_bin_get_data() which does access the transfer
buffer if it is set. To prevent an invalid memory access here, reset
urb->transfer_buffer to NULL when finished (musb_host_rx()), or do not
set it at all (musb_host_tx()).
Fixes: 8e8a551654 ("usb: musb: host: Handle highmem in PIO mode")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200316211136.2274-8-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62d65bdd9d upstream.
commit b401f8c4f4 ("USB: cdc-acm: fix rounding error in TIOCSSERIAL")
introduced a regression by changing the order of capability and close
settings change checks. When running with CAP_SYS_ADMIN setting the
close settings to the values already set resulted in -EOPNOTSUPP.
Fix this by changing the check order back to how it was before.
Fixes: b401f8c4f4 ("USB: cdc-acm: fix rounding error in TIOCSSERIAL")
Cc: Anthony Mallet <anthony.mallet@laas.fr>
Cc: stable <stable@vger.kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Matthias Reichl <hias@horus.com>
Link: https://lore.kernel.org/r/20200327150350.3657-1-hias@horus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we use core_inited for handling device mode pm, so we can
use it to better check if we can do run stop now, this is needed
if dwc->dev is runtime suspended before system sleep, after system
resume by usb, we need resume gadget by system resume without
runtime resume happened, see below sequence:
1. dwc3 core runtime suspended
2. system suspend: core suspend
3. system resume: core resume -> pm_runtime_set_active()
Then core runtime resume no chance to be called,
because current condition check:
if (pm_runtime_suspended())
return;
run_stop can't be enabled.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
As we have to clear wakeup irq until system pm resume, to avoid
frequently entering irq handler when usb wakeup system, disable
irq and enable it after wakeup irq is cleared.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
No function change, change dwc to be dwc_imx to keep consistent
for read.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Align the role check condition with threaded irq handler, with
dual role switch it's possible dwc->xhci is the previous host
but current role is device.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
As now we have 3 clocks to handle, it may deserve to use bulk
clk API to handle them, the new added clk is hsio root, this clock
actually belongs to hsiomix, which used to control the power domain
of USB and PCIE, currently we set it to be always on in dts by adding
it to init-on-array of clk node, after PCIE also can handle this clock
in its driver like USB, we can remove that clk from init-on-array.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Thinh Nguyen