For the minnowboard to work the values found in EMGD are required.
This might break Oaktrail but without hardware to test with I cannot
really tell (and do not really care).
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This turned out to be tricky. Writing to SDVOB on the primary vdc also
writes to SDVOB on the aux vdc, but reading it back on the primary vdc
always fails. Basically we never read from the primary vdc since we
will end up trashing the aux vdc.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Since we can have SDVO on Pipe B we better check the output type instead
of pipe number for Oaktrail HDMI.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
On SDVO pipes (always Pipe B on mrst) we have to sequentially write the
aux vdc. We might be able to skip programming the primary vdc in
some/most places but we don't care about that now.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
We start off by adding SDVO limits and converting all limits to the
generic gma_limit_t stuct. Then we separate clock calculations for
LVDS and SDVO. This will be cleaned up later but keep it simple for now.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Bit a bit -fixes pull request in the merge window than usual dua to two
feauture-y things:
- Display CRCs are now enabled on all platforms, including the odd DP case
on gm45/vlv. Since this is a testing-only feature it should ever hurt,
but I figured it'll help with regression-testing -fixes. So I left it
in and didn't postpone it to 3.14.
- Display power well refactoring from Imre. Would have caused major pain
conflict with the bdw stage 1 patches if I'd postpone this to -next.
It's only an relatively small interface rework, so shouldn't cause pain.
It's also been in my tree since almost 3 weeks already.
That accounts for about two thirds of the pull, otherwise just bugfixes:
- vlv backlight fix from Jesse/Jani
- vlv vblank timestamp fix from Jesse
- improved edp detection through vbt from Ville (fixes a vlv issue)
- eDP vdd fix from Paulo
- fixes for dvo lvds on i830M
- a few smaller things all over
Note: This contains a backmerge of v3.12. Since the -internal branch
always applied on top of -nightly I need that unified base to merge bdw
patches. So you'll get a conflict with radeon connector props when pulling
this (and nouveau/master will also conflict a bit when Ben doesn't
rebase). The backmerge itself only had conflicts in drm/i915.
There's also a tiny conflict between Jani's backlight fix and your sysfs
lifetime fix in drm-next.
* tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel: (940 commits)
drm/i915/vlv: use per-pipe backlight controls v2
drm/i915: make backlight functions take a connector
drm/i915: move opregion asle request handling to a work queue
drm/i915/vlv: use PIPE_START_VBLANK interrupts on VLV
drm/i915: Make intel_dp_is_edp() less specific
drm/i915: Give names to the VBT child device type bits
drm/i915/vlv: enable HDA display audio for Valleyview2
drm/i915/dvo: call ->mode_set callback only when the port is running
drm/i915: avoid unclaimed registers when capturing the error state
drm/i915: Enable DP port CRC for the "auto" source on g4x/vlv
drm/i915: scramble reset support for DP port CRC on vlv
drm/i915: scramble reset support for DP port CRC on g4x
drm/i916: add "auto" pipe CRC source
...
Conflicts:
MAINTAINERS
drivers/gpu/drm/i915/intel_panel.c
drivers/gpu/drm/nouveau/core/subdev/mc/base.c
drivers/gpu/drm/radeon/atombios_encoders.c
drivers/gpu/drm/radeon/radeon_connectors.c
Let's be a bit more consistent with our error values.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I want to merge in the new Broadwell support as a late hw enabling
pull request. But since the internal branch was based upon our
drm-intel-nightly integration branch I need to resolve all the
oustanding conflicts in drm/i915 with a backmerge to make the 60+
patches apply properly.
We'll propably have some fun because Linus will come up with a
slightly different merge solution.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_crt.c
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_drv.h
All rather simple adjacent lines changed or partial backports from
-next to -fixes, with the exception of the thaw code in i915_dma.c.
That one needed a bit of shuffling to restore the intent.
Oh and the massive header file reordering in intel_drv.h is a bit
trouble. But not much.
v2: Also don't forget the fixup for the silent conflict that results
in compile fail ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- CRC support from Damien and He Shuang. Long term this should allow us to
test an awful lot modesetting corner cases automatically. So for me as
the maintainer this is really big.
- HDMI audio fix from Jani.
- VLV dpll computation code refactoring from Ville.
- Fixups for the gpu booster from last time around (Chris).
- Some cleanups in the context code from Ben.
- More watermark work from Ville (we'll be getting there ...).
- vblank timestamp improvements from Ville.
- CONFIG_FB=n support, including drm core changes to make the fbdev
helpers optional.
- DP link training improvements (Jani).
- mmio vtable from Ben, prep work for future hw.
* tag 'drm-intel-next-2013-10-18' of git://people.freedesktop.org/~danvet/drm-intel: (132 commits)
drm/i915/dp: don't mention eDP bpp clamping if it doesn't affect bpp
drm/i915: remove dead code in ironlake_crtc_mode_set
drm/i915: crc support for hsw
drm/i915: fix CRC debugfs setup
drm/i915: wait one vblank when disabling CRCs
drm/i915: use ->get_vblank_counter for the crc frame counter
drm/i915: wire up CRC interrupt for ilk/snb
drm/i915: add CRC #defines for ilk/snb
drm/i915: extract display_pipe_crc_update
drm/i915: don't Oops in debugfs for I915_FBDEV=n
drm/i915: set HDMI pixel clock in audio configuration
drm/i915: pass mode to ELD write vfuncs
cpufreq: Add dummy cpufreq_cpu_get/put for CONFIG_CPU_FREQ=n
drm/i915: check gem bo size when creating framebuffers
drm/i915: Use unsigned long for obj->user_pin_count
drm/i915: prevent tiling changes on framebuffer backing storage
drm/i915: grab dev->struct_mutex around framebuffer_init
drm/i915: vlv: fix VGA hotplug after modeset
drm: add support for additional stereo 3D modes
drm/i915: preserve dispaly init order on ByT
...
So drm was abusing device lifetimes, by having embedded device structures
in the minor and connector it meant that the lifetime of the internal drm
objects (drm_minor and drm_connector) were tied to the lifetime of the device
files in sysfs, so if something kept those files opened the current code
would kfree the objects and things would go downhill from there.
Now in reality there is no need for these lifetimes to be so intertwined,
especailly with hotplugging of devices where we wish to remove the sysfs
and userspace facing pieces before we can unwind the internal objects due
to open userspace files or mmaps, so split the objects out so the struct
device is no longer embedded and do what fbdev does and just allocate
and remove the sysfs inodes separately.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Following files contains code that is common to all intel mid
soc's. So renamed them as below.
mrst/mrst.c -> intel-mid/intel-mid.c
mrst/vrtc.c -> intel-mid/intel_mid_vrtc.c
mrst/early_printk_mrst.c -> intel-mid/intel_mid_vrtc.c
pci/mrst.c -> pci/intel_mid_pci.c
Also, renamed the corresponding header files and made changes
to the driver files that included these header files.
To ensure that there are no functional changes, I have compared
the objdump of renamed files before and after rename and found
that the only difference is file name change.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: http://lkml.kernel.org/r/1382049336-21316-4-git-send-email-david.a.cohen@linux.intel.com
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
For drivers which might want to disable fbdev legacy support.
Select the new option in all drivers for now, so this shouldn't result
in any change. Drivers need some work anyway to make fbdev support
optional (if they have it implemented, that is), so the recommended
way to expose this is by adding per-driver options. At least as long
as most drivers don't support disabling the fbdev support.
v2: Update for new drm drivers msm and rcar-du. Note that Rob's msm
driver can already take advantage of this, which allows us to build
msm without any fbdev depencies in the kernel!
v3: Move the MODULE_* stuff from the fbdev helper file to
drm_crtc_helper.c.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 8b9ba7a3 'drm/gma500: use gem get/put page helpers' was missing a
line, which resulted in garbled screen.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Guillaume CLÉMENT <gclement@baobob.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We can get the PCI vendor and device IDs via dev->pdev. So we can drop
the duplicated information.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_vblank_init() is too ugly. Make it a bit easier on the eye by
collecting all the per-crtc vblank counters, timestamps etc. to
a structure and just allocate an array of those.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
vblank_disable_allowed is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All drivers embed gem-objects into their own buffer objects. There is no
reason to keep drm_gem_object_alloc(), gem->driver_private and
->gem_init_object() anymore.
New drivers are highly encouraged to do the same. There is no benefit in
allocating gem-objects separately.
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
Here's some gma500 unifying and cleanups for drm-next. There is more stuff in
the pipe for 3.12 but I'd like to get these out of the way first.
* 'gma500-next' of git://github.com/patjak/drm-gma500: (35 commits)
drm/gma500/cdv: Add and hook up chip op for disabling sr
drm/gma500/cdv: Add and hook up chip op for watermarks
drm/gma500: Rename psb_intel_encoder to gma_encoder
drm/gma500: Rename psb_intel_connector to gma_connector
drm/gma500: Rename psb_intel_crtc to gma_crtc
drm/gma500/cdv: Convert to generic set_config()
drm/gma500/psb: Convert to generic set_config()
drm/gma500: Add generic set_config() function
drm/gma500/cdv: Convert to generic save/restore
drm/gma500/psb: Convert to generic save/restore
drm/gma500: Add generic crtc save/restore funcs
drm/gma500: Convert to generic encoder funcs
drm/gma500: Add generic encoder functions
drm/gma500/psb: Convert to generic cursor funcs
drm/gma500/cdv: Convert to generic cursor funcs
drm/gma500: Add generic cursor functions
drm/gma500/psb: Convert to generic crtc->destroy
drm/gma500/mdfld: Use identical generic crtc funcs
drm/gma500/oak: Use identical generic crtc funcs
drm/gma500/psb: Convert to gma_crtc_dpms()
...
Some Poulsbo cards seem to incorrectly report SDVO_CMD_STATUS_TARGET_NOT_SPECIFIED instead of SDVO_CMD_STATUS_PENDING, which causes the display to be turned off.
Signed-off-by: Guillaume Clement <gclement@baobob.org>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The gma500 driver somehow set the DRIVER_IRQ_VBL flag, but since
there's no code at all to check for this we can kill it. The other two
are completely unused.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
So I've stumbled over drm_fasync and wondered what it does. Digging
that up is quite a story.
First I've had to read up on what this does and ended up being rather
bewildered why peopled loved signals so much back in the days that
they've created SIGIO just for that ...
Then I wondered how this ever works, and what that strange "No-op."
comment right above it should mean. After all calling the core fasync
helper is pretty obviously not a noop. After reading through the
kernels FASYNC implementation I've noticed that signals are only sent
out to the processes attached with FASYNC by calling kill_fasync.
No merged drm driver has ever done that.
After more digging I've found out that the only driver that ever used
this is the so called GAMMA driver. I've frankly never heard of such a
gpu brand ever before. Now FASYNC seems to not have been the only bad
thing with that driver, since Dave Airlie removed it from the drm
driver with prejudice:
commit 1430163b4bbf7b00367ea1066c1c5fe85dbeefed
Author: Dave Airlie <airlied@linux.ie>
Date: Sun Aug 29 12:04:35 2004 +0000
Drop GAMMA DRM from a great height ...
Long story short, the drm fasync support seems to be doing absolutely
nothing. And the only user of it was never merged into the upstream
kernel. And we don't need any fops->fasync callback since the fcntl
implementation in the kernel already implements the noop case
correctly.
So stop this particular cargo-cult and rip it all out.
v2: Kill drm_fasync assignments in rcar (newly added) and imx drivers
(somehow I've missed that one in staging). Also drop the reference in
the drm DocBook. ARM compile-fail reported by Rob Clark.
v3: Move the removal of dev->buf_asnyc assignment in drm_setup to this
patch here.
v4: Actually git add ... tsk.
Cc: Dave Airlie <airlied@linux.ie>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Clark <robdclark@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a callback hook to the chip ops struct to allow chips to have their
specific self-refresh function. Currently only used by cdv.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Add a callback hook to the chip ops struct to allow chips to have their
specific fifo watermark update function. Currently only cdv actually
tries to set wms based on crtc configuration but if/when the other chips
needs it we can attach a callback for them as well.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Because, there is no reason for it not to be const.
v1: original
v2: fix compile break in vmwgfx, and couple related cleanups suggested
by Ville Syrjälä
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All the gem based kms drivers really want the same function to
destroy a dumb framebuffer backing storage object.
So give it to them and roll it out in all drivers.
This still leaves the option open for kms drivers which don't use GEM
for backing storage, but it does decently simplify matters for gem
drivers.
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Cc: Ben Skeggs <skeggsb@gmail.com>
Reviwed-by: Rob Clark <robdclark@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the new vma manager instead of the old hashtable. Also convert all
drivers to use the new convenience helpers. This drops all the
(map_list.hash.key << PAGE_SHIFT) non-sense.
Locking and access-management is exactly the same as before with an
additional lock inside of the vma-manager, which strictly wouldn't be
needed for gem.
v2:
- rebase on drm-next
- init nodes via drm_vma_node_reset() in drm_gem.c
v3:
- fix tegra
v4:
- remove duplicate if (drm_vma_node_has_offset()) checks
- inline now trivial drm_vma_node_offset_addr() calls
v5:
- skip node-reset on gem-init due to kzalloc()
- do not allow mapping gem-objects with offsets (backwards compat)
- remove unneccessary casts
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Use the generic gma functions instead of the medfield functions where
they are identical.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Use the generic gma functions instead of the oaktrail functions where
they are identical.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This takes care of the remaining chips using the old generic code.
We don't check if the pipe number is valid but the old code peeked in
the register map before checking anyways so just ignore it.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
There is a slight difference in how we pick the palette register in the
generic function but we should be ok as long as psb_intel_crtc->pipe and
the register map is sane.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This patch makes psb use the gma_xxx counterparts that are identical. I
took them in one sweep as they should not cause any regressions.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This patch makes cdv use the gma_xxx counterparts that are identical. I
took them in one sweep as they should not cause any regressions.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Add chip specific callbacks for the generic and non-generic clock
calculation code. Also remove as much dupilicated code as possible.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Replace any use of xxx_intel_pipe_has_type() with the generic
gma_pipe_has_type() function. Poulsbo still use it but that will be
removed when we rip out psb_intel_pipe_has_type().
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Add chip specific callbacks for the generic and non-generic clock
calculation code. Also remove as much dupilicated code as possible.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This patch aims to unify the bits and pieces that are common (or similar
enough) for pll clock calculations. Nothing makes use of this code yet
That will come in later patches.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
drm_gem_object_init() and drm_gem_private_object_init() do exactly the
same (except for shmem alloc) so make the first use the latter to reduce
code duplication.
Also drop the return code from drm_gem_private_object_init(). It seems
unlikely that we will extend it any time soon so no reason to keep it
around. This simplifies code paths in drivers, too.
Last but not least, fix gma500 to call drm_gem_object_release() before
freeing objects that were allocated via drm_gem_private_object_init().
That isn't actually necessary for now, but might be in the future.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Patrik writes:
Two fixes for memory leaks split into Cedarview and Poulsbo versions,
and a fix for properly setting the pipe base when using fbdev. It's on
my todo-list to start unifying the chips since they are very similar,
but until then I'd like to split them up in case there are side-effects
on Cedarview that I cannot currently test.
airled: Verified pull from github matches what I expected.
* 'gma500-fixes' of git://github.com/patjak/drm-gma500:
drm/gma500/cdv: Fix cursor gem obj referencing on cdv
drm/gma500/psb: Fix cursor gem obj referencing on psb
drm/gma500/cdv: Unpin framebuffer on crtc disable
drm/gma500/psb: Unpin framebuffer on crtc disable
drm/gma500: Add fb gtt offset to fb base
The internal crtc cursor gem object pointer was never set/updated since
it was required to be set in the first place.
Fixing this will make the pin/unpin count match and prevent cursor
objects from leaking when userspace drops all references to it. Also
make sure we drop the gem obj reference on failure.
This patch only affects Cedarview chips.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
The internal crtc cursor gem object pointer was never set/updated since
it was required to be set in the first place.
Fixing this will make the pin/unpin count match and prevent cursor
objects from leaking when userspace drops all references to it. Also
make sure we drop the gem obj reference on failure.
This patch only affects Poulsbo chips.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
The framebuffer needs to be unpinned in the crtc->disable callback
because of previous pinning in psb_intel_pipe_set_base(). This will fix
a memory leak where the framebuffer was released but not unpinned
properly. This patch only affects Cedarview.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=889511
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=812113
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
The framebuffer needs to be unpinned in the crtc->disable callback
because of previous pinning in psb_intel_pipe_set_base(). This will fix
a memory leak where the framebuffer was released but not unpinned
properly. This patch only affects Poulsbo.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=889511
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=812113
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Old code assumed framebuffer starts at base of stolen memory. Since the
addition of hardware cursors, this might not be true anymore so add the
gtt offset to the calculation.
Reported-by: Holger Schurig <holgerschurig@gmail.com>
Tested-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 3.10.
Wierd bits:
- OMAP drm changes required OMAP dss changes, in drivers/video, so I
took them in here.
- one more fbcon fix for font handover
- VT switch avoidance in pm code
- scatterlist helpers for gpu drivers - have acks from akpm
Highlights:
- qxl kms driver - driver for the spice qxl virtual GPU
Nouveau:
- fermi/kepler VRAM compression
- GK110/nvf0 modesetting support.
Tegra:
- host1x core merged with 2D engine support
i915:
- vt switchless resume
- more valleyview support
- vblank fixes
- modesetting pipe config rework
radeon:
- UVD engine support
- SI chip tiling support
- GPU registers initialisation from golden values.
exynos:
- device tree changes
- fimc block support
Otherwise:
- bunches of fixes all over the place."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (513 commits)
qxl: update to new idr interfaces.
drm/nouveau: fix build with nv50->nvc0
drm/radeon: fix handling of v6 power tables
drm/radeon: clarify family checks in pm table parsing
drm/radeon: consolidate UVD clock programming
drm/radeon: fix UPLL_REF_DIV_MASK definition
radeon: add bo tracking debugfs
drm/radeon: add new richland pci ids
drm/radeon: add some new SI PCI ids
drm/radeon: fix scratch reg handling for UVD fence
drm/radeon: allocate SA bo in the requested domain
drm/radeon: fix possible segfault when parsing pm tables
drm/radeon: fix endian bugs in atom_allocate_fb_scratch()
OMAPDSS: TFP410: return EPROBE_DEFER if the i2c adapter not found
OMAPDSS: VENC: Add error handling for venc_probe_pdata
OMAPDSS: HDMI: Add error handling for hdmi_probe_pdata
OMAPDSS: RFBI: Add error handling for rfbi_probe_pdata
OMAPDSS: DSI: Add error handling for dsi_probe_pdata
OMAPDSS: SDI: Add error handling for sdi_probe_pdata
OMAPDSS: DPI: Add error handling for dpi_probe_pdata
...
Two fixes for gma500. First one from Anisse allows us to handle ASLE irqs even
when BIOS doesn't trigger a pipe event irq. The second one allows dual head
setups to have a big shared framebuffer.
* 'gma500-fixes' of git://github.com/patjak/drm-gma500:
drm/gma500: Increase max resolution for mode setting
drm/gma500: fix backlight hotkeys behaviour on netbooks
By having a higher max resolution we can now set up a virtual
framebuffer that spans several monitors. 4096 should be ok since we're
gen 3 or higher and should be enough for most dual head setups.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Backlight hotkeys weren't working before on certain cedartrail laptops.
The source of this problem is that the hotkeys' ASLE opregion interrupts
were simply ignored. Driver seemed to expect the interrupt to be
associated with a pipe, but it wasn't.
Accepting the ASLE interrupt without an associated pipe event flag fixes
the issue, the backlight code is called when needed, making the
brightness keys work properly.
[patrik: This patch affects irq handling on any netbook with opregion support]
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=833597
Reference: http://lists.freedesktop.org/archives/dri-devel/2012-July/025279.html
Cc: stable@kernel.org
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Patrik writes:
I haven't had much review or testing on other platforms than Poulsbo but
at least the following Cedarview bug has been squashed and no
regressions reported: https://bugs.freedesktop.org/show_bug.cgi?id=58527
* 'gma500-next' of git://github.com/patjak/drm-gma500:
drm/gma500: Add debugging info to psb_gtt_restore()
drm/gma500: Check connector status before restoring sdvo
gma500:fix build failure for 3.9-rc5
drm/gma500: Fix hibernation problems on sdvo encoders
drm/gma500: Add hooks for hibernation
drm/gma500: Activate the gtt rebuild on suspend/resume
drm/gma500: Add support for rebuilding the gtt
drm/gma500: Change fb name so pm-utils doesn't apply quirks
gma500: Make VGA and HDMI connector hotpluggable
drm/gma500: Clean up various defines
drm/gma500: Remove unnecessary function exposure
drm/gma500: Type clock limits directly into array and remove defines
drm/gma500: Calculate clock in one function instead of three identical
drm/gma500: Remove unused i8xx clock limits
gma500: medfield: Fix possible NULL pointer dereference
drivers: gpu: drm: gma500: Replaced calls kzalloc & memcpy with kmemdup
gma500: remove unused drm_psb_no_fb
This patch fixes a bug introduced by:
commit 749387dc8d
Author: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Date: Sun Apr 7 16:35:50 2013 +0200
drm/gma500: Fix hibernation problems on sdvo encoders
The bug is triggered when we do a mode set on a sdvo encoder with all
connectors in the disconnected state. A crtc is considered enabled by
drm even though all of its connectors are disconnected. Work around
this by adding a check in our sdvo restore function.
Also remove the unneeded dpms on. Prepare and Commit will take care of
that.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Last version of this patch is not clear enough and X86 duplicated.
This patch fixes build failure of v3.9-rc5 and rc6.
When config ACPI_VIDEO as m, DRM_GMA500 as y, here comes the failure.
GMA5/600 needs acpi_video just like nouveau.
And some tab type fix by the way.
Failure message:
drivers/built-in.o: In function `psb_driver_load':
kernel-3.9-rc5/drivers/gpu/drm/gma500/psb_drv.c:340: \
undefined reference to `acpi_video_register'
make: *** [vmlinux] Error 1
Signed-off-by: Xiong Zhou <jencce.kernel@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
The state of the SDVO chip is more difficult to save than the LVDS so we do a
full mode set on the crtc to get SDVO operational again. The SDVOB/C register is
also stored just in case we have special bits set in the future.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Currently we do whatever is done during suspend/resume but we might need some
more work for hibernation so keep them in separate functions.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This patch activates the rebuilding of the gtt. Currently we reinitialize the
gtt by inserting the stolen pages again and map the rest to our scratch page.
Then we go about restoring the needed ranges. This is a bit overkill but right
now we don't have that much to restore so better safe than sorry.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
By having 'drm' and 'fb' in the fb screeninfo id, pm-utils will leave us
alone. Otherwise we'll have quirks up to our ears and resume will break.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Both VGA and HDMI connectors are available on my Asus EeePC X101CH.
This patch will cause output to be shown on either when plugged in.
For both, it shows the leftmost 800x600, of the 1024x600 on LVDS.
Signed-off-by: Kero van Gelder <kero@chello.nl>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
i2c_del_adapter() always returns 0. So all checks testing whether it will be
non zero will always evaluate to false and the conditional code is dead code.
This patch updates all callers of i2c_del_mux_adapter() to ignore the return
value and assume that it will always succeed (which it will). In a subsequent
patch the return type of i2c_del_adapter() will be made void.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
psb_intel_crtc_gamma_set() and psb_intel_crtc_destroy() aren't used outside of
psb_intel_display.c right now so no need to expose them.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This makes it easier to read. We do the same for cdv so it becomes more
consistent as well.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
i9xx_clock() and i8xx_clock() did the same calc and psb_intel_clock() just
called i9xx_clock() so just move it all into psb_intel_clock().
The same calculation is duplicated in cdv_intel_display.c as well so maybe we
can share it later on.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
The use of pointer sender should be after the NULL check.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Replaced calls kzalloc followed by memcpy with call to kmemdup.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
commit f9f23a77f07506a32d9dc1d925bf85c0e7507b66(gma500: remove no_fb bits)
remove all the drm_psb_no_fb relations code in gma500 except this line code,
so remove it also.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Pull drm merge from Dave Airlie:
"Highlights:
- TI LCD controller KMS driver
- TI OMAP KMS driver merged from staging
- drop gma500 stub driver
- the fbcon locking fixes
- the vgacon dirty like zebra fix.
- open firmware videomode and hdmi common code helpers
- major locking rework for kms object handling - pageflip/cursor
won't block on polling anymore!
- fbcon helper and prime helper cleanups
- i915: all over the map, haswell power well enhancements, valleyview
macro horrors cleaned up, killing lots of legacy GTT code,
- radeon: CS ioctl unification, deprecated UMS support, gpu reset
rework, VM fixes
- nouveau: reworked thermal code, external dp/tmds encoder support
(anx9805), fences sleep instead of polling,
- exynos: all over the driver fixes."
Lovely conflict in radeon/evergreen_cs.c between commit de0babd60d
("drm/radeon: enforce use of radeon_get_ib_value when reading user cmd")
and the new changes that modified that evergreen_dma_cs_parse()
function.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (508 commits)
drm/tilcdc: only build on arm
drm/i915: Revert hdmi HDP pin checks
drm/tegra: Add list of framebuffers to debugfs
drm/tegra: Fix color expansion
drm/tegra: Split DC_CMD_STATE_CONTROL register write
drm/tegra: Implement page-flipping support
drm/tegra: Implement VBLANK support
drm/tegra: Implement .mode_set_base()
drm/tegra: Add plane support
drm/tegra: Remove bogus tegra_framebuffer structure
drm: Add consistency check for page-flipping
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
gma500: Fix n, m1 and m2 clock limits for sdvo and lvds
...
The values of n, m1 and m2 needs to be subtracted by 2 before writing them to
the FP register. The dot clock calculation already thinks of these values in
register form so we must also specify them as such.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
