Currently vesafb/efifb/... is kicked when hardware driver is registering
framebuffer. To do it hardware must be fully functional, so there's a short
window between start of initialisation and framebuffer registration when
two drivers touch the hardware. Unfortunately sometimes it breaks nouveau
initialisation.
Fix it by kicking firmware driver(s) before we start touching the hardware.
Reported-by: Didier Spaier <didier.spaier@epsm.fr>
Tested-by: Didier Spaier <didier.spaier@epsm.fr>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It removes a hack from nouveau code which had to detect which
region to pass to kick vesafb/efifb.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Recently I've studied my system dmesg and seen this:
<lots of stuff before>
1 [ 0.478416] ACPI: Battery Slot [C1B4] (battery present)
2 [ 0.478648] ACPI: Battery Slot [C1B3] (battery absent)
3 [ 0.906678] [drm] initialized overlay support
4 [ 1.762304] Console: switching to colour frame buffer device 128x48
5 [ 1.765211] fb0: inteldrmfb frame buffer device
6 [ 1.765242] registered panic notifier
7 [ 1.765272] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
8 [ 1.765372] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
<lots of stuff after>
and it was not evident who registered that panic notifier on line 6.
I'd bought it as some low-level stuff needed by kernel itself, but the
time was inappropriate -- too late for such things.
So I had to study sources to see it was drm who was registering
switch-to-fb on panic.
Let's avoid possible confusion and mark this message as going from drm
subsystem.
(I'm a bit unsure whether to use '[drm]:' or 'drm:' -- the rest of the
kernel just uses 'topic:', and even in drm_fb_helper.c we use 'fb%d:'
without [] brackets. Either way is ok with me.)
Signed-off-by: Kirill Smelkov <kirr@landau.phys.spbu.ru>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Userspace need to know the hw crtc id (0, 1, 2, ...) from the drm
crtc id. Bump the minor version so userspace can enable conditionaly
features depend on this.
V2 use num_crtc and avoid DRM_ERROR
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Having hsync both start and end on pixel 1072 ain't gonna work very
well. Matches the X server's list.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-By: Michael Tokarev <mjt@tls.msk.ru>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Reviewed-by: Corbin Simpson <MostAwesomeDude@gmail.com>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Smatch complained that we initialize 6 elements in add_detailed_modes()
but the timings[] array is declared with 5 elements. Adam Jackson
verified that 6 is the correct number of timings.
On Mon, May 10, 2010 at 12:08:24PM -0400, Adam Jackson wrote:
> > > struct std_timing timings[5];
> > > ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
>
> This decl is wrong, should be 6. From the 1.4 spec:
>
> "Six additional Standard Timings may be listed as a display descriptor
> (tag #FAh)."
>
> The 1.3 spec is a little less explicit about it, but does show 6
> standard timing codes in the 0xFA detailed subblock, terminated by 0x0A
> in the 18th byte. I don't have the docs for 1.2 or earlier, but we're
> paranoid enough about not adding broken timings that we should be fine.
This patch is basically a clean up, because timings[] is declared inside
a union and increasing the number of elements here doesn't change the
overall size of the union.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix typos in vga/Kconfig file
and use GPU (upper case) consistently.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
We don't use timing_level any more after: 9cf00977da "drm/edid: Unify
detailed block parsing between base and extension blocks".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes LVDS issues on some laptops; notably laptops with
2048x1536 panels.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously we just set them to dpms off. This should save
additional power.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the memory is not iomem we should not try to
ioremap it. Should fix :
https://bugs.freedesktop.org/show_bug.cgi?id=27822
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previous reset code leaded to computer hard lockup (need to unplug
the power too reboot the computer) on various configuration. This
patch change the reset code to avoid hard lockup. The GPU reset
is failing most of the time but at least user can log in remotely
or properly shutdown the computer.
Two issues were leading to hard lockup :
- Writting to the scratch register lead to hard lockup most likely
because the write back mecanism is in fuzy state after GPU lockup.
- Resetting the GPU memory controller and not reinitializing it
after leaded to hard lockup. We did only reinitialize in case of
successfull reset thus unsuccessfull reset quickly leaded to hard
lockup.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Implements irq support for HDMI audio output. Now the polling timer
is only enabled if irq support isn't available.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rework HDMI audio polling timer, only enable it when
at least one HDMI encoder needs it. Preparation for
replacing it with irq support.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Convert most AGP chipset to use scratch page as default entries.
This help avoiding GPU querying 0 address and trigger computer
fault. With KMS and memory manager we bind/unbind AGP memory
constantly and it seems that some GPU are still doing AGP
traffic even after GPU report being idle with the memory segment.
Tested (radeon GPU KMS + Xorg + compiz + glxgears + quake3) on :
- SIS 1039:0001 & 1039:0003
- Intel 865 8086:2571
Compile tested for other bridges
V2 enable scratch page on uninorth
V3 fix unbound check in uninorth insert memory (Michel Dänzer)
V4 rebase on top of drm-next branch with the lastest intel AGP
changeset (stable should use version V3 of the patch)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a DRM DocBook providing basic information about DRM interfaces, including
TTM, GEM, KMS and vblank infrastructure. Intended to provide information to
new and existing developers about how to perform driver initialization,
implement mode setting and other DRM features.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On my 945 laptop + radeon GPU, I was getting an oops on boot without this
check which seems to have gotten dropped in the rework.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Eric mentioned on irc this patch was bad, so revert it.
This reverts commit fb8b5a39b6.
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-ttm-unmappable:
drm/radeon/kms: enable use of unmappable VRAM V2
drm/ttm: remove io_ field from TTM V6
drm/vmwgfx: add support for new TTM fault callback V5
drm/nouveau/kms: add support for new TTM fault callback V5
drm/radeon/kms: add support for new fault callback V7
drm/ttm: ttm_fault callback to allow driver to handle bo placement V6
drm/ttm: split no_wait argument in 2 GPU or reserve wait
Conflicts:
drivers/gpu/drm/nouveau/nouveau_bo.c
This patch enable the use of unmappable VRAM thanks to
previous TTM infrastructure change.
V2 update after io_mem_reserve/io_mem_free callback balancing
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All TTM driver have been converted to new io_mem_reserve/free
interface which allow driver to choose and return proper io
base, offset to core TTM for ioremapping if necessary. This
patch remove what is now deadcode.
V2 adapt to match with change in first patch of the patchset
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 adjust to minor cleanup
V5 remove the needs ioremap flag
V6 keep the ioremapping facility in TTM
[airlied- squashed driver removals in here also]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add the support for the new fault callback, does change anything
from driver point of view.
Improvement: store the aperture base in a variable so that we don't
call a function to get it on each fault.
Patch hasn't been tested.
V2 don't derefence bo->mem.mm_node as it's not NULL only for
VRAM or GTT
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 callback has to ioremap
V5 ioremap is done by TTM
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add the support for the new fault callback, does change anything
from driver point of view, thought it should allow nouveau to add
support for unmappable VRAM.
Improvement: store the aperture base in a variable so that we don't
call a function to get it on each fault.
Patch hasn't been tested on any hw.
V2 don't derefence bo->mem.mm_node as it's not NULL only for
VRAM or GTT
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 callback has to ioremap
V5 ioremap is done by ttm
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add the support for the new fault callback and also the
infrastructure for supporting unmappable VRAM.
V2 validate BO with no_wait = true
V3 don't derefence bo->mem.mm_node as it's not NULL only for
VRAM or GTT
V4 update to splitted no_wait ttm change
V5 update to new balanced io_mem_reserve/free change
V6 callback is responsible for iomapping memory
V7 move back iomapping to ttm
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On fault the driver is given the opportunity to perform any operation
it sees fit in order to place the buffer into a CPU visible area of
memory. This patch doesn't break TTM users, nouveau, vmwgfx and radeon
should keep working properly. Future patch will take advantage of this
infrastructure and remove the old path from TTM once driver are
converted.
V2 return VM_FAULT_NOPAGE if callback return -EBUSY or -ERESTARTSYS
V3 balance io_mem_reserve and io_mem_free call, fault_reserve_notify
is responsible to perform any necessary task for mapping to succeed
V4 minor cleanup, atomic_t -> bool as member is protected by reserve
mecanism from concurent access
V5 the callback is now responsible for iomapping the bo and providing
a virtual address this simplify TTM and will allow to get rid of
TTM_MEMTYPE_FLAG_NEEDS_IOREMAP
V6 use the bus addr data to decide to ioremap or this isn't needed
but we don't necesarily need to ioremap in the callback but still
allow driver to use static mapping
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Luckily the change is quite a little bit less invasive than I've
feared.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Thanks to the to_intel_bo helper, this change is rather trivial.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just embed it and adjust the pointers, No other changes (that's
for later patches).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just preparation, no functional change.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When drivers embed the core gem object into their own structures,
they'll have to do this. Temporarily this results in an ugly
kfree(gem_obj);
in every gem driver.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This function can be used by drivers who allocate the drm gem object
on their own. No functional change in here, just preparation.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-radeon-evergreen-accel:
drm/radeon: fix cypress firmware typo.
drm/radeon/kms/evergreen: add hpd support
drm/radeon/kms/evergreen: implement irq support
drm/radeon/kms/evergreen: setup and enable the CP
drm/radeon/kms/evergreen: implement gfx init
drm/radeon/kms/evergreen: add soft reset function
drm/radeon/kms/evergreen: add gart support
drm/radeon/kms: add support for evergreen power tables
drm/radeon/kms: update atombios.h power tables for evergreen
* drm-fbdev-cleanup:
drm/fb: remove drm_fb_helper_setcolreg
drm/kms/fb: use slow work mechanism for normal hotplug also.
drm/kms/fb: add polling support for when nothing is connected.
drm/kms/fb: provide a 1024x768 fbcon if no outputs found.
drm/kms/fb: separate fbdev connector list from core drm connectors
drm/kms/fb: move to using fb helper crtc grouping instead of core crtc list
drm/fb: fix fbdev object model + cleanup properly.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/nouveau/nouveau_drv.h
* drm-edid-fixes:
drm/edid: When checking duplicate standard modes, walked the probed list
drm/edid: Fix sync polarity for secondary GTF curve
drm/modes: Fix interlaced mode names
drm/edid: Add secondary GTF curve support
drm/edid: Strengthen the algorithm for standard mode codes
drm/edid: Fix the HDTV hack.
drm/edid: Extend range-based mode addition for EDID 1.4
drm/edid: Add test for monitor reduced blanking support.
drm/edid: Fix preferred mode parse for EDID 1.4
drm/edid: Remove some silly comments
drm/edid: Remove arbitrary EDID extension limit
drm/edid: Add modes for Established Timings III section
drm/edid: Reshuffle mode list construction to closer match the spec
drm/edid: Remove a redundant check
drm/edid: Remove some misleading comments
drm/edid: Fix secondary block fetch.
* drm-ttm-pool:
drm/ttm: using kmalloc/kfree requires including slab.h
drm/ttm: include linux/seq_file.h for seq_printf
drm/ttm: Add sysfs interface to control pool allocator.
drm/ttm: Use set_pages_array_wc instead of set_memory_wc.
arch/x86: Add array variants for setting memory to wc caching.
drm/nouveau: Add ttm page pool debugfs file.
drm/radeon/kms: Add ttm page pool debugfs file.
drm/ttm: Add debugfs output entry to pool allocator.
drm/ttm: add pool wc/uc page allocator V3
* 'anholt/drm-intel-next' of /home/airlied/kernel/drm-next: (48 commits)
agp/intel-gtt: kill previous_size assignments
agp/intel-gtt: kill intel_i830_tlbflush
agp/intel: split out gmch/gtt probe, part 1
agp/intel: kill mutli_gmch_chip
agp/intel: uncoditionally reconfigure driver on resume
agp/intel: split out the GTT support
agp/intel: introduce intel-agp.h header file
drm/i915: Don't touch PORT_HOTPLUG_EN in intel_dp_detect()
drm/i915/pch: Use minimal number of FDI lanes (v2)
drm/i915: Add the support of memory self-refresh on Ironlake
drm/i915: Move Pineview CxSR and watermark code into update_wm hook.
drm/i915: Only save/restore FBC on the platform that supports FBC
drm/i915: Fix the incorrect argument for SDVO SET_TV_format command
drm/i915: Add support of SDVO on Ibexpeak PCH
drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on).
drm/i915: do not read uninitialized ->dev_private
Revert "drm/i915: Use a dmi quirk to skip a broken SDVO TV output."
drm/i915: implement multifunction SDVO device support
drm/i915: remove unused intel_pipe_get_connector()
drm/i915: remove connector object in old output structure
...
The recent anon_vma fixes cause many anonymous pages to end up
in the parent process anon_vma, even when the page is exclusively
owned by the current process.
Adding exclusively owned anonymous pages to the top anon_vma
reduces rmap scanning overhead, especially in workloads with
forking servers.
This patch adds a parameter to __page_set_anon_rmap that can
be used to indicate whether or not the added page is exclusively
owned by the current process.
Pages added through page_add_new_anon_rmap are exclusively
owned by the current process, and can be added to the top
anon_vma.
Pages added through page_add_anon_rmap can be either shared
or exclusively owned, so we do the conservative thing and
add it to the oldest anon_vma.
A next step would be to add the exclusive parameter to
page_add_anon_rmap, to be used from functions where we do
know for sure whether a page is exclusively owned.
Signed-off-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Lightly-tested-by: Borislav Petkov <bp@alien8.de>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
[ Edited to look nicer - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
eCryptfs: Turn lower lookup error messages into debug messages
eCryptfs: Copy lower directory inode times and size on link
ecryptfs: fix use with tmpfs by removing d_drop from ecryptfs_destroy_inode
ecryptfs: fix error code for missing xattrs in lower fs
eCryptfs: Decrypt symlink target for stat size
eCryptfs: Strip metadata in xattr flag in encrypted view
eCryptfs: Clear buffer before reading in metadata xattr
eCryptfs: Rename ecryptfs_crypt_stat.num_header_bytes_at_front
eCryptfs: Fix metadata in xattr feature regression
Vaugue warnings about ENAMETOOLONG errors when looking up an encrypted
file name have caused many users to become concerned about their data.
Since this is a rather harmless condition, I'm moving this warning to
only be printed when the ecryptfs_verbosity module param is 1.
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
The timestamps and size of a lower inode involved in a link() call was
being copied to the upper parent inode. Instead, we should be
copying lower parent inode's timestamps and size to the upper parent
inode. I discovered this bug using the POSIX test suite at Tuxera.
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Since tmpfs has no persistent storage, it pins all its dentries in memory
so they have d_count=1 when other file systems would have d_count=0.
->lookup is only used to create new dentries. If the caller doesn't
instantiate it, it's freed immediately at dput(). ->readdir reads
directly from the dcache and depends on the dentries being hashed.
When an ecryptfs mount is mounted, it associates the lower file and dentry
with the ecryptfs files as they're accessed. When it's umounted and
destroys all the in-memory ecryptfs inodes, it fput's the lower_files and
d_drop's the lower_dentries. Commit 4981e081 added this and a d_delete in
2008 and several months later commit caeeeecf removed the d_delete. I
believe the d_drop() needs to be removed as well.
The d_drop effectively hides any file that has been accessed via ecryptfs
from the underlying tmpfs since it depends on it being hashed for it to
be accessible. I've removed the d_drop on my development node and see no
ill effects with basic testing on both tmpfs and persistent storage.
As a side effect, after ecryptfs d_drops the dentries on tmpfs, tmpfs
BUGs on umount. This is due to the dentries being unhashed.
tmpfs->kill_sb is kill_litter_super which calls d_genocide to drop
the reference pinning the dentry. It skips unhashed and negative dentries,
but shrink_dcache_for_umount_subtree doesn't. Since those dentries
still have an elevated d_count, we get a BUG().
This patch removes the d_drop call and fixes both issues.
This issue was reported at:
https://bugzilla.novell.com/show_bug.cgi?id=567887
Reported-by: Árpád Bíró <biroa@demasz.hu>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Cc: Dustin Kirkland <kirkland@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
If the lower file system driver has extended attributes disabled,
ecryptfs' own access functions return -ENOSYS instead of -EOPNOTSUPP.
This breaks execution of programs in the ecryptfs mount, since the
kernel expects the latter error when checking for security
capabilities in xattrs.
Signed-off-by: Christian Pulvermacher <pulvermacher@gmx.de>
Cc: stable@kernel.org
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Create a getattr handler for eCryptfs symlinks that is capable of
reading the lower target and decrypting its path. Prior to this patch,
a stat's st_size field would represent the strlen of the encrypted path,
while readlink() would return the strlen of the decrypted path. This
could lead to confusion in some userspace applications, since the two
values should be equal.
https://bugs.launchpad.net/bugs/524919
Reported-by: Loïc Minier <loic.minier@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Commit b91ecb00 ("gigaset: include cleanup cleanup") removed an implicit
sched.h inclusion that came in via slab.h, and caused various compile
problems as a result.
This should fix it.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marcin Slusarz