According to the DP 1.1 spec, the sink must power
up within 1ms. Noticed while reviewing Thierry's
drm/dp patches.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As per the DP1.2 spec. Noticed while reviewing
Thierry's drm/dp patches. Also bump native aux
retries to 7 for consistency.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is the preferred flushing method on CIK.
Note, this only works on the PFP so the engine bit must be
set.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
i915 doesn't need this kludge for most platforms. Although we do
appear to need something similar on certain platforms, but we can
be more accurate when we apply the adjustment since we know exactly
why the scanline counter doesn't always quite match the vblank
status.
Also the current code doesn't handle interlaced modes correctly,
and we already deal with interlaced modes in i915 code.
So let's just move the current code to radeon_get_crtc_scanoutpos()
since that's why it was added. For i915 we'll add a more finely
targeted variant.
v2: Fix vpos vs. *vpos bug (Mario)
Reviewed-by: mario.kleiner.de@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Preparation for moving the early vblank IRQ logic into
radeon_get_crtc_scanoutpos().
v2: Fix radeon_drv.c compile warning (Mario)
Reviewed-by: mario.kleiner.de@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
crtc_clock is now supposed to be the actual pixel clock corresponding to
the other crtc_ timing values. Populate crtc_clock appropriately in
radeon_atom_get_tv_timings().
This was the only obvious place where we frob with the crtc_ timigns
directly instead of calling drm_mode_set_crtcinfo() which would also
update crtc_clock.
Reviewed-by: mario.kleiner.de@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Rather than using crtc->hwmode, just pass the relevant mode to
drm_calc_vbltimestamp_from_scanoutpos(). This removes the last hwmode
usage from core drm.
Reviewed-by: mario.kleiner.de@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
drm-intel-next-2014-01-10:
- final bits for runtime D3 on Haswell from Paul (now enabled fully)
- parse the backlight modulation freq information in the VBT from Jani
(but not yet used)
- more watermark improvements from Ville for ilk-ivb and bdw
- bugfixes for fastboot from Jesse
- watermark fix for i830M (but not yet everything)
- vlv vga hotplug w/a (Imre)
- piles of other small improvements, cleanups and fixes all over
Note that the pull request includes a backmerge of the last drm-fixes
pulled into Linus' tree - things where getting a bit too messy. So the
shortlog also contains a bunch of patches from Linus tree. Please yell if
you want me to frob it for you a bit.
* 'drm-intel-next' of git://people.freedesktop.org/~danvet/drm-intel: (609 commits)
drm/i915/bdw: make sure south port interrupts are enabled properly v2
drm/i915: Include more information in disabled hotplug interrupt warning
drm/i915: Only complain about a rogue hotplug IRQ after disabling
drm/i915: Only WARN about a stuck hotplug irq ONCE
drm/i915: s/hotplugt_status_gen4/hotplug_status_g4x/
* acpi-cleanup: (22 commits)
ACPI / tables: Return proper error codes from acpi_table_parse() and fix comment.
ACPI / tables: Check if id is NULL in acpi_table_parse()
ACPI / proc: Include appropriate header file in proc.c
ACPI / EC: Remove unused functions and add prototype declaration in internal.h
ACPI / dock: Include appropriate header file in dock.c
ACPI / PCI: Include appropriate header file in pci_link.c
ACPI / PCI: Include appropriate header file in pci_slot.c
ACPI / EC: Mark the function acpi_ec_add_debugfs() as static in ec_sys.c
ACPI / NVS: Include appropriate header file in nvs.c
ACPI / OSL: Mark the function acpi_table_checksum() as static
ACPI / processor: initialize a variable to silence compiler warning
ACPI / processor: use ACPI_COMPANION() to get ACPI device
ACPI: correct minor typos
ACPI / sleep: Drop redundant acpi_disabled check
ACPI / dock: Drop redundant acpi_disabled check
ACPI / table: Replace '1' with specific error return values
ACPI: remove trailing whitespace
ACPI / IBFT: Fix incorrect <acpi/acpi.h> inclusion in iSCSI boot firmware module
ACPI / i915: Fix incorrect <acpi/acpi.h> inclusions via <linux/acpi_io.h>
SFI / ACPI: Fix warnings reported during builds with W=1
...
Conflicts:
drivers/acpi/nvs.c
drivers/hwmon/asus_atk0110.c
If you feed the tool a suitable bogus register map you can break it
in arbitary (code executing) ways. While this isn't a particularly
exciting or probable attack vector we still ought to fix it.
One of a set of sscanf issues reported by Jackie Chang
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
pci config reset is a low level reset that resets
the entire chip from the bus interface. It can
be more reliable if soft reset fails.
v2: fix rebase
v3: hide behind module parameter
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pci config reset is a low level reset that resets
the entire chip from the bus interface. It can
be more reliable if soft reset fails.
v2: hide behind module parameter
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pci config reset is a low level reset that resets
the entire chip from the bus interface. It can
be more reliable if soft reset fails.
v2: put behind module parameter
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pci config reset is a low level reset that resets
the entire chip from the bus interface. It can
be more reliable if soft reset fails.
There's not much information still available on
r6xx, so r6xx is based on guess-work.
v2: put behind module parameter
v3: add IGP check
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is used to hard reset the asic. If a soft
reset is not able to reset things, a hard reset
can be used.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enabling this parameter enables pci config reset,
aka hard reset, which is a bus level chip reset.
In some cases this works more reliably than a soft
reset. Disabled by default.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes a bug which was causing rejections of valid GPU commands
from userspace.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's never allocated on systems without an ATOMBIOS or COMBIOS ROM.
Should fix an oops I encountered while resetting the GPU after a lockup
on my PowerBook with an RV350.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Move prototype declarations of functions radeon_get_encoder_enum() and
radeon_link_encoder_connector() to header file drm/radeon/radeon_mode.h
because they are used by more than one file.
This eliminates the following warnings in drm/radeon/radeon_encoders.c:
drivers/gpu/drm/radeon/radeon_encoders.c:86:1: warning: no previous prototype for ‘radeon_get_encoder_enum’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_encoders.c:162:1: warning: no previous prototype for ‘radeon_link_encoder_connector’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move prototype declaration of functions radeon_add_atom_connector() and
radeon_add_legacy_connector() to header file drm/radeon/radeon_mode.h
because they are used by more than one file.
This eliminates the following warning in drm/radeon/radeon_connectors.c:
drivers/gpu/drm/radeon/radeon_connectors.c:1588:1: warning: no previous prototype for ‘radeon_add_atom_connector’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_connectors.c:2020:1: warning: no previous prototype for ‘radeon_add_legacy_connector’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
fixes warnings with -Wmissing-prototypes
Based on initial patches from Rashika Kheria.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Rashika Kheria <rashika.kheria@gmail.com>
Noticed by Rashika Kheria and cherry-picked from
her larger patch set.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Rashika Kheria <rashika.kheria@gmail.com>
Noticed by Rashika Kheria and cherry-picked from
her larger patch set.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Rashika Kheria <rashika.kheria@gmail.com>
Noticed by Rashika Kheria and cherry-picked from
her larger patch set.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Rashika Kheria <rashika.kheria@gmail.com>
Include header file drm/radeon/ci_dpm.h in drm/radeon/ci_smc.c because
it uses function declared in the header file.
This eliminates the following warnings in drm/radeon/ci_smc.c:
drivers/gpu/drm/radeon/ci_smc.c:46:5: warning: no previous prototype for ‘ci_copy_bytes_to_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:113:6: warning: no previous prototype for ‘ci_start_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:121:6: warning: no previous prototype for ‘ci_reset_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:129:5: warning: no previous prototype for ‘ci_program_jump_on_start’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:136:6: warning: no previous prototype for ‘ci_stop_smc_clock’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:145:6: warning: no previous prototype for ‘ci_start_smc_clock’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:154:6: warning: no previous prototype for ‘ci_is_smc_running’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:165:14: warning: no previous prototype for ‘ci_send_msg_to_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:186:14: warning: no previous prototype for ‘ci_wait_for_smc_inactive’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:204:5: warning: no previous prototype for ‘ci_load_smc_ucode’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:251:5: warning: no previous prototype for ‘ci_read_smc_sram_dword’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:266:5: warning: no previous prototype for ‘ci_write_smc_sram_dword’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move prototype declaration of function radeon_atom_copy_swap() to header
file drm/radeon/radeon_mode.h because it is used by more than one file.
This eliminates the following warnings in drm/radeon/atombios_dp.c:
drivers/gpu/drm/radeon/atombios_dp.c:53:6: warning: no previous prototype for ‘radeon_atom_copy_swap’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Include header file gpu/drm/radeon/sislands_smc.h in drm/radeon/si_smc.c
because it uses function declared in the header file.
Remove prototype declaration of function si_set_smc_sram_address() from
drm/radeon/sislands_smc.h because the function is used only in one file
where it is declared static already.
This eliminates the following warnings in drm/radeon/si_smc.c:
drivers/gpu/drm/radeon/si_smc.c:46:5: warning: no previous prototype for ‘si_copy_bytes_to_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:112:6: warning: no previous prototype for ‘si_start_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:121:6: warning: no previous prototype for ‘si_reset_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:135:5: warning: no previous prototype for ‘si_program_jump_on_start’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:142:6: warning: no previous prototype for ‘si_stop_smc_clock’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:151:6: warning: no previous prototype for ‘si_start_smc_clock’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:160:6: warning: no previous prototype for ‘si_is_smc_running’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:171:14: warning: no previous prototype for ‘si_send_msg_to_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:192:14: warning: no previous prototype for ‘si_wait_for_smc_inactive’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:210:5: warning: no previous prototype for ‘si_load_smc_ucode’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:269:5: warning: no previous prototype for ‘si_read_smc_sram_dword’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:284:5: warning: no previous prototype for ‘si_write_smc_sram_dword’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add static keyword to the definition of KMS_INVALID_IOCTL(name) in
radeon_kms.c because the functions passed to it as arguments are not
used anywhere else.
This eliminates the following warnings in drm/radeon/radeon_kms.c:
drivers/gpu/drm/radeon/radeon_kms.c:719:1: warning: no previous prototype for ‘radeon_cp_init_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:720:1: warning: no previous prototype for ‘radeon_cp_start_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:721:1: warning: no previous prototype for ‘radeon_cp_stop_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:722:1: warning: no previous prototype for ‘radeon_cp_reset_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:723:1: warning: no previous prototype for ‘radeon_cp_idle_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:724:1: warning: no previous prototype for ‘radeon_cp_resume_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:725:1: warning: no previous prototype for ‘radeon_engine_reset_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:726:1: warning: no previous prototype for ‘radeon_fullscreen_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:727:1: warning: no previous prototype for ‘radeon_cp_swap_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:728:1: warning: no previous rototype for ‘radeon_cp_clear_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:729:1: warning: no previous prototype for ‘radeon_cp_vertex_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:730:1: warning: no previous rototype for ‘radeon_cp_indices_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:731:1: warning: no previous prototype for ‘radeon_cp_texture_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:732:1: warning: no previous prototype for ‘radeon_cp_stipple_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:733:1: warning: no previous prototype for ‘radeon_cp_indirect_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:734:1: warning: no previous prototype for ‘radeon_cp_vertex2_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:735:1: warning: no previous prototype for ‘radeon_cp_cmdbuf_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:736:1: warning: no previous prototype for ‘radeon_cp_getparam_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:737:1: warning: no previous prototype for ‘radeon_cp_flip_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:738:1: warning: no previous prototype for ‘radeon_mem_alloc_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:739:1: warning: no previous prototype for ‘radeon_mem_free_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:740:1: warning: no previous rototype for ‘radeon_mem_init_heap_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:741:1: warning: no previous rototype for ‘radeon_irq_emit_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:742:1: warning: no previous prototype for ‘radeon_irq_wait_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:743:1: warning: no previous rototype for ‘radeon_cp_setparam_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:744:1: warning: no previous prototype for ‘radeon_surface_alloc_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:745:1: warning: no previous prototype for ‘radeon_surface_free_kms’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark function r600_audio_set_dto() as static in drm/radeon/r600_hdmi.c
because it is not used outside this file.
This eliminates the following warning in drm/radeon/r600_hdmi.c:
drivers/gpu/drm/radeon/r600_hdmi.c:253:6: warning: no previous prototype for ‘r600_audio_set_dto’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark function radeon_gem_set_domain() as static in
drm/radeon/radeon_gem.c because it is not used outside this file.
This eliminates the following warning in drm/radeon/radeon_gem.c:
drivers/gpu/drm/radeon/radeon_gem.c:89:5: warning: no previous prototype for ‘radeon_gem_set_domain’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark function radeon_info_ioctl() as static in drm/radeon/radeon_kms.c
because it is not used outside this file.
This eliminates the following warning in drm/radeon/radeon_kms.c:
drivers/gpu/drm/radeon/radeon_kms.c:194:5: warning: no previous prototype for ‘radeon_info_ioctl’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark functions radeon_doorbell_init() and radeon_doorbell_fini() as
static in drm/radeon/radeon_device.c because they are not used outside
this file.
This eliminates the following warning in drm/radeon/radeon_device.c:
drivers/gpu/drm/radeon/radeon_device.c:252:5: warning: no previous prototype for ‘radeon_doorbell_init’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_device.c:281:6: warning: no previous prototype for ‘radeon_doorbell_fini’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark function radeon_bo_clear_va() as static in
drm/radeon/radeon_object.c because it is not used outside this file.
This eliminates the following warning in drm/radeon/radeon_object.c:
drivers/gpu/drm/radeon/radeon_object.c:49:6: warning: no previous prototype for ‘radeon_bo_clear_va’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hw i2c engines are disabled by default as the
current implementation is still experimental. Print
a warning when users enable it so that it's obvious
when the option is enabled.
v2: check for non-0 rather than 1
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
- VGA switcheroo was broken for some users as a result of the ACPI-based
PCI hotplug (ACPIPHP) changes in 3.12, because some previously ignored
hotplug events started to be handled. The fix causes them to be
ignored again.
- There are two more issues related to cpufreq's suspend/resume handling
changes from the 3.12 cycle addressed by Viresh Kumar's fixes.
- intel_pstate triggers a divide error in a timer function if the P-state
information it needs is missing during initialization. This leads to
kernel panics on nested KVM clients and is fixed by failing the
initialization cleanly in those cases.
- PCI initalization code changes during the 3.9 cycle uncovered BIOS
issues related to ACPI wakeup notifications (some BIOSes send them
for devices that aren't supposed to support ACPI wakeup). Work around
them by installing an ACPI wakeup notify handler for all PCI devices
with ACPI support.
- The Calxeda cpuilde driver's probe function is tagged as __init, which
is incorrect and causes a section mismatch to occur during build. Fix
from Andre Przywara removes the __init tag from there.
- During the 3.12 cycle ACPIPHP started to print warnings about missing
_ADR for devices that legitimately don't have it. Fix from Toshi Kani
makes it only print the warnings where they make sense.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=LXh0
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and PM fixes and new device IDs from Rafael Wysocki:
"These commits, except for one, are regression fixes and the remaining
one fixes a divide error leading to a kernel panic. The majority of
the regressions fixed here were introduced during the 3.12 cycle, one
of them is from this cycle and one is older.
Specifics:
- VGA switcheroo was broken for some users as a result of the
ACPI-based PCI hotplug (ACPIPHP) changes in 3.12, because some
previously ignored hotplug events started to be handled. The fix
causes them to be ignored again.
- There are two more issues related to cpufreq's suspend/resume
handling changes from the 3.12 cycle addressed by Viresh Kumar's
fixes.
- intel_pstate triggers a divide error in a timer function if the
P-state information it needs is missing during initialization.
This leads to kernel panics on nested KVM clients and is fixed by
failing the initialization cleanly in those cases.
- PCI initalization code changes during the 3.9 cycle uncovered BIOS
issues related to ACPI wakeup notifications (some BIOSes send them
for devices that aren't supposed to support ACPI wakeup). Work
around them by installing an ACPI wakeup notify handler for all PCI
devices with ACPI support.
- The Calxeda cpuilde driver's probe function is tagged as __init,
which is incorrect and causes a section mismatch to occur during
build. Fix from Andre Przywara removes the __init tag from there.
- During the 3.12 cycle ACPIPHP started to print warnings about
missing _ADR for devices that legitimately don't have it. Fix from
Toshi Kani makes it only print the warnings where they make sense"
* tag 'pm+acpi-3.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
intel_pstate: Fail initialization if P-state information is missing
ARM/cpuidle: remove __init tag from Calxeda cpuidle probe function
PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
cpufreq: preserve user_policy across suspend/resume
cpufreq: Clean up after a failing light-weight initialization
ACPI / PCI / hotplug: Avoid warning when _ADR not present
* acpi-pci-pm:
PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
* acpi-pci-hotplug:
ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
ACPI / PCI / hotplug: Avoid warning when _ADR not present
The changes in the ACPI-based PCI hotplug (ACPIPHP) subsystem made
during the 3.12 development cycle uncovered a problem with VGA
switcheroo that on some systems, when the device-specific method
(ATPX in the radeon case, _DSM in the nouveau case) is used to turn
off the discrete graphics, the BIOS generates ACPI hotplug events for
that device and those events cause ACPIPHP to attempt to remove the
device from the system (they are events for a device that was present
previously and is not present any more, so that's what should be done
according to the spec). Then, the system stops functioning correctly.
Since the hotplug events in question were simply silently ignored
previously, the least intrusive way to address that problem is to
make ACPIPHP ignore them again. For this purpose, introduce a new
ACPI device flag, no_hotplug, and modify ACPIPHP to ignore hotplug
events for PCI devices whose ACPI companions have that flag set.
Next, make the radeon and nouveau switcheroo detection code set the
no_hotplug flag for the discrete graphics' ACPI companion.
Fixes: bbd34fcdd1 (ACPI / hotplug / PCI: Register all devices under the given bridge)
References: https://bugzilla.kernel.org/show_bug.cgi?id=61891
References: https://bugzilla.kernel.org/show_bug.cgi?id=64891
Reported-and-tested-by: Mike Lothian <mike@fireburn.co.uk>
Reported-and-tested-by: <madcatx@atlas.cz>
Reported-and-tested-by: Joaquín Aramendía <samsagax@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Fill in asic family specific versions rather than
using the generic version. This lets us handle asic
specific differences more easily. In this case, we
disable sw swapping of the rtpr writeback value on
r6xx+ since the hw does it for us. Fixes bogus
rptr readback on BE systems.
v2: remove missed cpu_to_le32(), add comments
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable coarse grained clockgating. This works properly now
that smc is initialized earlier than the rlc and cp.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable coarse grained clockgating on CIK dGPUs. This
works properly now that smc is initialized earlier than
the rlc and cp.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need more control over the ordering of dpm init with
respect to the rest of the asic. Specifically, the SMC
has to be initialized before the rlc and cg/pg. The pm
code currently initializes late in the driver, but we need
it to happen much earlier so move pm handling into the asic
specific callbacks.
This makes dpm more reliable and makes clockgating work
properly on CIK parts and should help on SI parts as well.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Right now it's called right after enable, but after
reworking the dpm init order, it will get called later
to accomodate loading the smc early, but enabling
thermal interrupts and block powergating later after
the ring tests are complete.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure interrupts are enabled
before we enable thermal interrupts.
Also, don't powergate uvd, etc. until after
the ring tests.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure interrupts are enabled
before we enable thermal interrupts.
Also, don't powergate uvd until after
the ring tests.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to wait to enable cg and pg until after
ring tests. Also make sure interrupts are enabled
before we enable thermal interrupts.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to wait to enable cg and pg until after
ring tests. Also make sure interrupts are enabled
before we enable thermal interrupts.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Certain features need to be enabled after ring tests
(e.g., powergating, etc.). Add a function pointer
to split out late enable features.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to reorder the driver init sequence to better accomodate
dpm which needs to be loaded earlier in the init sequence. Move
fw init up so that it's available for dpm init.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: add default_llseek
v3: set inode size in the open callback
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not very fast, but makes it possible to access even the
normally inaccessible parts of VRAM from userspace.
v2: use MM_INDEX_HI for >2GB mem access, add default_llseek
v3: set inode size in the open callback
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise we not necessary export the right information.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We don't have the NUM_BANKS parameter, so we have to calculate it
from the other parameters. NUM_BANKS is not constant on CIK.
This fixes 2D tiling for the display engine on CIK.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This will allow userspace to correctly program the PA_SC_RASTER_CONFIG
register, so it can be considered a fix.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Only the render backends of the first shader engine were enabled. The others
were erroneously disabled. Enabling the other render backends improves
performance a lot.
Unigine Sanctuary on Bonaire:
Before: 15 fps
After: 90 fps
Judging from the fan noise, the GPU was also underclocked when the other
render backends were disabled, resulting in horrible performance. The fan is
a lot noisy under load now.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Otherwise the kernel might reject our decoding requests.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The real linux interfaces are soooo much easier on the eyes ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I've killed them a long time ago in drm/i915, let's get rid of this
remnant of shared drm core days for good.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We don't have any userspace interfaces that use HZ as a time unit, so
having our own DRM define is useless.
Remove this remnant from the shared drm core days.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Most place actually want to just check for dev->agp (most do, but a
few don't so this fixes a few potential NULL derefs). The only
exception is the agp init code which should check for the AGP driver
feature flag.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current values seem to be defined in a format that's specific to the
i915, gma500 and radeon drivers. To make this more generally useful, use
the values as defined in the specification.
While at it, prefix the constants with DP_ for improved namespacing.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Spread spectrum seems to cause hangs when dynamic clock
switching is enabled. Disable it for now. This does not
affect performance or the amount of power saved. Tracked
down by Martin Andersson.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69723
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This causes a race condition between drm_dev_unregister()
and pci_driver.shutdown at shutdown or driver unload time.
We need to revisit how to properly support kexec within
the drm.
This reverts commit 846ae41ae9.
Otherwise we end up with a rather strange looking result.
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Tom Stellard <thomas.stellard@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I implemented support for this, but forget to hook
up the callback so the driver can actually use it.
On asics with a dedicated DMA engine, we use the DMA
engine for buffer migration so this is just for testing
purposes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit ec39f64bba (drm/radeon/dpm: Convert
to use devm_hwmon_register_with_groups) converted one usage of
dev_get_drvdata, but there were two more.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=72457
Signed-off-by: Martin Andersson <g02maran@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some RS690 boards with 64MB of sideport memory show up as
having 128MB sideport + 256MB of UMA. In this case,
just skip the sideport memory and use UMA. This fixes
rendering corruption and should improve performance.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=35457
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some boards seem to have garbage in the upper
16 bits of the vram size register. Check for
this and clamp the size properly. Fixes
boards reporting bogus amounts of vram.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This register was incorrect for evergreen and cayman.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
According to documentation, 0x00008A60 should be PA_SU_LINE_STIPPLE_VALUE.
Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is based on a similar patch from Alexandre Demers.
While fixing up some warnings with that patch I saw some
additional cleanups that could be applied. This patch
simplifies the logic for patching the power state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Alexandre Demers <alexandre.f.demers@gmail.com>
Also rename the function to better reflect what it is doing.
agd5f: fix argument size warning
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Simplify the code and fix race condition seen because
attribute files were created after hwmon device registration.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Copy-paste typo. Value should be 0-2, not 0-1.
Noticed-by: Sylvain BERTRAND <sylware@legeek.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
More fixes for radeon. This adds new queries for tiling on CIK, and
fixes a crash in handling acpi atif backlight events on CIK.
Some fixes for radeon for 3.13. Mostly CI stability fixes. I think
I've tracked down the stability problems with dpm on Trinity/Richland,
so I'm going to enable that by default now.
* 'drm-next-3.13' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: hook up backlight functions for CI and KV family.
drm/radeon/cik: Add macrotile mode array query
drm/radeon/cik: Return backend map information to userspace
drm/radeon: enable DPM by default in TN asics
drm/radeon: adjust TN dpm parameters for stability (v2)
drm/radeon: use a single doorbell for cik kms compute
drm/radeon/vm: don't attempt to update ptes if ib allocation fails
drm/radeon: disable CIK CP semaphores for now
drm/radeon: allow semaphore emission to fail
drm/radeon: add semaphore trace point
radeon: workaround pinning failure on low ram gpu
radeon/i2c: do not count reg index in number of i2c byte we are writing.
drm/radeon: cypress_dpm: Fix unused variable warning when CONFIG_ACPI=n
drm: radeon: ni_dpm: Fix unused variable warning when CONFIG_ACPI=n
- ACPI-based device hotplug fixes for issues introduced recently and
a fix for an older error code path bug in the ACPI PCI host bridge
driver.
- Fix for recently broken OMAP cpufreq build from Viresh Kumar.
- Fix for a recent hibernation regression related to s2disk.
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar.
- System suspend error code path fix related to runtime PM and
runtime PM documentation update from Ulf Hansson.
- cpufreq's conservative governor fix from Xiaoguang Chen.
- New processor IDs for intel_idle and turbostat and removal of
an obsolete Kconfig option from Len Brown.
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg.
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu.
- Rework of the ACPI companion representation in struct device and
code cleanup related to that change from Rafael J Wysocki,
Lan Tianyu and Jarkko Nikula.
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices
from Jarkko Nikula.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=QMp+
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
- ACPI-based device hotplug fixes for issues introduced recently and a
fix for an older error code path bug in the ACPI PCI host bridge
driver
- Fix for recently broken OMAP cpufreq build from Viresh Kumar
- Fix for a recent hibernation regression related to s2disk
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar
- System suspend error code path fix related to runtime PM and runtime
PM documentation update from Ulf Hansson
- cpufreq's conservative governor fix from Xiaoguang Chen
- New processor IDs for intel_idle and turbostat and removal of an
obsolete Kconfig option from Len Brown
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu
- Rework of the ACPI companion representation in struct device and code
cleanup related to that change from Rafael J Wysocki, Lan Tianyu and
Jarkko Nikula
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices from
Jarkko Nikula
* tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration
ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed()
ACPI / PCI root: Clear driver_data before failing enumeration
ACPI / hotplug: Fix PCI host bridge hot removal
ACPI / hotplug: Fix acpi_bus_get_device() return value check
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
ACPI / video: clean up DMI table for initial black screen problem
ACPI / EC: Ensure lock is acquired before accessing ec struct members
PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps()
ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac
spi: Use stable dev_name for ACPI enumerated SPI slaves
i2c: Use stable dev_name for ACPI enumerated I2C slaves
ACPI: Provide acpi_dev_name accessor for struct acpi_device device name
ACPI / bind: Use (put|get)_device() on ACPI device objects too
ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro
ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
PM / Runtime: Fix error path for prepare
PM / Runtime: Update documentation around probe|remove|suspend
cpufreq: conservative: set requested_freq to policy max when it is over policy max
...
Fixes crashes when handling atif events due to the lack of a
callback being registered.
Signed-off-by: Samuel Li <samuel.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This is required to properly calculate the tiling parameters
in userspace.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is required to properly calculate the tiling parameters
in userspace.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After adjusting the dpm parameters this seems to be
stable on most TN systems. DPM is important for APUs
since the boot clocks are generally pretty low.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adjust some of the TN dpm settings for stability. Enabling
these features causes hangs and other stability problems
on certain boards.
v2: leave uvd dpm enabled
Bug:
https://bugzilla.kernel.org/show_bug.cgi?id=63101
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
A single doorbell page is plenty for cik kms compute.
Use a single page and manage doorbell allocation by
individual doorbells rather than pages. Identify
doorbells by their index rather than byte offset.
Signed-off-by: Andrew Lewycky <Andrew.Lewycky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If we fail to allocate an indirect buffer (ib) when updating
the ptes, return an error instead of trying to use the ib.
Avoids a null pointer dereference.
Bug:
https://bugzilla.kernel.org/show_bug.cgi?id=58621
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
To workaround bugs and/or certain limits it's sometimes
useful to fall back to waiting on fences.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
GPU with low amount of ram can fails at pinning new framebuffer before
unpinning old one. On such failure, retry with unpinning old one before
pinning new one allowing to work around the issue. This is somewhat
ugly but only affect those old GPU we care about.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Useless to count the register index in number of bytes we are writing.
Fixes a regression with hw i2c enabled.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
With CONFIG_ACPI=n the following build warning is seen:
drivers/gpu/drm/radeon/cypress_dpm.c:302:31: warning: unused variable 'eg_pi' [-Wunused-variable]
Protect eg_pi with CONFIG_ACPI.
Based on patch from: Fabio Estevam <fabio.estevam@freescale.com>
but doesn't mix allocation and code.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With CONFIG_ACPI=n the following build warning is seen:
drivers/gpu/drm/radeon/ni_dpm.c:3448:31: warning: unused variable 'eg_pi' [-Wunused-variable]
Move the definition of eg_pi inside the CONFIG_ACPI 'if' block.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull drm updates from Dave Airlie:
"This is a combo of -next and some -fixes that came in in the
intervening time.
Highlights:
New drivers:
ARM Armada driver for Marvell Armada 510 SOCs
Intel:
Broadwell initial support under a default off switch,
Stereo/3D HDMI mode support
Valleyview improvements
Displayport improvements
Haswell fixes
initial mipi dsi panel support
CRC support for debugging
build with CONFIG_FB=n
Radeon:
enable DPM on a number of GPUs by default
secondary GPU powerdown support
enable HDMI audio by default
Hawaii support
Nouveau:
dynamic pm code infrastructure reworked, does nothing major yet
GK208 modesetting support
MSI fixes, on by default again
PMPEG improvements
pageflipping fixes
GMA500:
minnowboard SDVO support
VMware:
misc fixes
MSM:
prime, plane and rendernodes support
Tegra:
rearchitected to put the drm driver into the drm subsystem.
HDMI and gr2d support for tegra 114 SoC
QXL:
oops fix, and multi-head fixes
DRM core:
sysfs lifetime fixes
client capability ioctl
further cleanups to device midlayer
more vblank timestamp fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (789 commits)
drm/nouveau: do not map evicted vram buffers in nouveau_bo_vma_add
drm/nvc0-/gr: shift wrapping bug in nvc0_grctx_generate_r406800
drm/nouveau/pwr: fix missing mutex unlock in a failure path
drm/nv40/therm: fix slowing down fan when pstate undefined
drm/nv11-: synchronise flips to vblank, unless async flip requested
drm/nvc0-: remove nasty fifo swmthd hack for flip completion method
drm/nv10-: we no longer need to create nvsw object on user channels
drm/nouveau: always queue flips relative to kernel channel activity
drm/nouveau: there is no need to reserve/fence the new fb when flipping
drm/nouveau: when bailing out of a pushbuf ioctl, do not remove previous fence
drm/nouveau: allow nouveau_fence_ref() to be a noop
drm/nvc8/mc: msi rearm is via the nvc0 method
drm/ttm: Fix vma page_prot bit manipulation
drm/vmwgfx: Fix a couple of compile / sparse warnings and errors
drm/vmwgfx: Resource evict fixes
drm/edid: compare actual vrefresh for all modes for quirks
drm: shmob_drm: Convert to clk_prepare/unprepare
drm/nouveau: fix 32-bit build
drm/i915/opregion: fix build error on CONFIG_ACPI=n
Revert "drm/radeon/audio: don't set speaker allocation on DCE4+"
...
Since DEVICE_ACPI_HANDLE() is now literally identical to
ACPI_HANDLE(), replace it with the latter everywhere and drop its
definition from include/acpi.h.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify struct acpi_dev_node to contain a pointer to struct acpi_device
associated with the given device object (that is, its ACPI companion
device) instead of an ACPI handle corresponding to it. Introduce two
new macros for manipulating that pointer in a CONFIG_ACPI-safe way,
ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the
ACPI_HANDLE() macro to take the above changes into account.
Drop the ACPI_HANDLE_SET() macro entirely and rework its users to
use ACPI_COMPANION_SET() instead. For some of them who used to
pass the result of acpi_get_child() directly to ACPI_HANDLE_SET()
introduce a helper routine acpi_preset_companion() doing an
equivalent thing.
The main motivation for doing this is that there are things
represented by struct acpi_device objects that don't have valid
ACPI handles (so called fixed ACPI hardware features, such as
power and sleep buttons) and we would like to create platform
device objects for them and "glue" them to their ACPI companions
in the usual way (which currently is impossible due to the
lack of valid ACPI handles). However, there are more reasons
why it may be useful.
First, struct acpi_device pointers allow of much better type checking
than void pointers which are ACPI handles, so it should be more
difficult to write buggy code using modified struct acpi_dev_node
and the new macros. Second, the change should help to reduce (over
time) the number of places in which the result of ACPI_HANDLE() is
passed to acpi_bus_get_device() in order to obtain a pointer to the
struct acpi_device associated with the given "physical" device,
because now that pointer is returned by ACPI_COMPANION() directly.
Finally, the change should make it easier to write generic code that
will build both for CONFIG_ACPI set and unset without adding explicit
compiler directives to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
This reverts commit 555b1b651a.
Let's try this again for 3.13. It's required for proper
interaction with alsa. Was disabled previously in 3.12
to be on the safe side since it caused problems on older
asics.
In order to have any realistic chance of calculating proper
ACR values, we need to be able to calculate both N and CTS,
not just CTS. We still aim for the ideal N as specified in
the HDMI spec though.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69675
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The values were taken from the HDMI spec, but they assumed
exact x/1.001 clocks. Since we round the clocks, we also need
to calculate different N and CTS values.
Note that the N for 25.2/1.001 MHz at 44.1 kHz audio is out of
spec. Hopefully this mode is rarely used and/or HDMI sinks
tolerate overly large values of N.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69675
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This just updates the firmware loading functions
to look for the appropriate firmware files for
hawaii.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The formula needs to be adjusted since there are 4 RBs
per SH rather than 2 as on previous asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The golden register settings are optimal settings for
certain registers from the hardware team.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The new HDP flush method doesn't seem to work reliably on
sDMA either, so use the old method here too.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To plug the VRAM memory leak (see previous patch for
details) we must unpin the frame buffer when disabling the
CRTC. This warrants the addition of disable function for legacy
CRTC, which puts the CRTC in DPMS-OFF state and unpins the
frame buffer if there is one associated with the CRTC.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When drm_helper_disable_unused_functions calls disable
function of the CRTC, it also sets the crtc->fb pointer
to NULL. This can later (when the mode on that CRTC is setup
again from user space) cause ***_do_set_base functions to
"think" that there is no old buffer and skip the unpinning
code. Consequently, the buffer that has been NULL-ified in
drm_helper_disable_unused_functions will never be unpinned
causing a leak in VRAM.
This patch plugs the leak by unpinning the frame buffer
in crtc_disable function.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The current code writing SADs to the audio registers seems to assume
that there is at most a single SAD per audio format.
However, that is not the case. Especially for PCM it is somewhat common
for sinks to have two SADs, one for 8-channel and one for 2-channel
audio, which may have different supported sample rates (i.e. the sink
supports stereo audio at higher sample rates than multichannel audio).
Because of this, only the 2-channel SAD may be used if it appears before
the 8-channel SAD. Unless other SADs require otherwise, this may cause
the ALSA HDA driver to allow stereo playback only.
Fix the code to pick the PCM SAD with the highest number of channels,
while merging the rate masks of PCM SADs with lower amount of channels
into the additional stereo rate mask byte.
Technically there are even more cases to handle (multiple non-PCM SADs
of the same type, more than two PCM SADs with varying channel counts,
etc), but those have not actually been encountered in the field and
handling them would be non-trivial.
Example affected EDID from Onkyo TX-SR674 specifying 192kHz stereo
support and 96kHz 8-channel support (and other 8-channel compressed
formats):
00ffffffffffff003dcb010000000001
ffff0103800000780a0dc9a057479827
12484c00000001010101010101010101
010101010101011d8018711c1620582c
2500c48e2100009e011d007251d01e20
6e285500c48e2100001e000000fc0054
582d53523637342020202020000000fd
00313d0f2e08000a202020202020019b
02032f724f8504030f0e07069413121e
1d1615012f097f070f1f071707503707
503f07c0834f000066030c00ffff808c
0ad08a20e02d10103e9600c48e210000
18011d80d0721c1620102c2580c48e21
00009e011d00bc52d01e20b8285540c4
8e2100001e8c0ad090204031200c4055
00c48e210000180000000000000000a8
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Andre Heider <a.heider@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
