When setting sync EIC as IRQ_TYPE_EDGE_BOTH type, we missed to set the
SPRD_EIC_SYNC_INTMODE register to 0, which means detecting edge signals.
Thus this patch fixes the issue.
Fixes: 25518e024e ("gpio: Add Spreadtrum EIC driver support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The NXP PCA6416, documented at [1], is a variant of the PCA GPIO
expander with 16 GPIOs, and supporting an interrupt.
[1] https://www.nxp.com/docs/en/data-sheet/PCA6416A.pdf
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When adding support for the pcal6416, the of_device_id table was left out,
add the proper entry.
Fixes: aac1e3c968 ("gpio: pca953x: add support for pcal6416 type")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit b764a5863f ("gpio: omap: Remove custom PM calls and use cpu_pm
instead") moved interrupt using GPIO banks to idle with cpu_pm in order
to drop the use of pm_runtime_irq_safe() in a later patch. The GPIO
banks with no interrupts claimed are still being idled based on PM
runtime calls. However this caused a regression for am437x suspend for
rtc+ddr idle mode where the device cannot enter idle state as reported
by Keerthy <j-keerthy@ti.com>.
To fix the issue, we must not fail the pm_runtime callbacks. For GPIO
interrupts, we already have irq_chip_pm_get increment the PM runtime
use count as pointed out by Grygorii Strashko <grygorii.strashko@ti.com>.
So all we need to do is remove the conditional handling in the
runtime_suspend and resume functions and let the CPU PM notifier idle
the GPIO banks.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes: b764a5863f ("gpio: omap: Remove custom PM calls and use cpu_pm instead")
Reported-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[tony@atomide.com: updated patch description, dropped runtime count changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO block can enter idle independently of the CPU power management
calls via smart-idle. When the GPIO block enters idle, level detection
stops working due to clocks being shut off, and an alternative form of
edge detection is used. However, this needs the edge detection
registers set to mark the appropriate edges.
Arrange to configure the edge detection enables along with the level
detection to ensure that any transition to active interrupt state that
occurs while the block is idle is detected as a wake-up event.
Since we enable the edge detection when configuring the IRQ, both
omap2_gpio_enable_level_quirk() nor omap2_gpio_disable_level_quirk()
become redundant, which also means OMAP_GPIO_QUIRK_IDLE_REMOVE_TRIGGER
can be removed. This can be now done without regressions as patch
"gpio: gpio-omap: fix level interrupt idling" allows level interrupts
to idle on omap4 without a workaround.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[tony@atomide.com: update description for the fix dependency]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- batch of improvements for the vf610 driver which shrink the code and
make use of resource managed helpers
- support for a new variant of pca953x
- make gpio-mockup buildable on systems without IOMEM
- make gpio-74x164 more flexible by using generic device properties
plus minor improvements
- new driver for Mellanox BlueField
- fixes for wakeup GPIOs in gpio-omap
- use devm_platform_ioremap_resource() in gpio-mxc
- a couple improvements of kernel docs for ACPI code
- don't WARN() in gpiod_put() on optional GPIOs
-----BEGIN PGP SIGNATURE-----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=mSS+
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.2-updates-for-linus-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio: updates for v5.2 (part 1)
- batch of improvements for the vf610 driver which shrink the code and
make use of resource managed helpers
- support for a new variant of pca953x
- make gpio-mockup buildable on systems without IOMEM
- make gpio-74x164 more flexible by using generic device properties
plus minor improvements
- new driver for Mellanox BlueField
- fixes for wakeup GPIOs in gpio-omap
- use devm_platform_ioremap_resource() in gpio-mxc
- a couple improvements of kernel docs for ACPI code
- don't WARN() in gpiod_put() on optional GPIOs
If a device is part of the wake-up path, it should indicate this by
setting its power.wakeup_path field. This allows the genpd core code to
keep the device enabled during system suspend when needed.
As regulators powering devices are not handled by genpd, the driver
handles these itself, and thus must skip regulator control when the
device is part of the wake-up path.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
EXPORT_SYMBOL_GPL() needs a semicolon at the end, also
explicitly include <linux/export.h> as well.
Fixes: 64ebde5b0f ("gpiolib: export devprop_gpiochip_set_names()")
Acked-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The direction inversion semantics are now handled by simply
using the registers for in/out available, no need to keep
track of inversion semantics exmplicitly anymore.
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
During my regression testing I noticed the cadence GPIO driver
fails on the latest gpio for-next tree.
I think the reason is this patch:
commit 96cd559817f2 ("Merge branch 'devel' into for-next")
Here is a part of the test log:
Loopback 8 -> 24
TESTING: gpio: 488: output direction PASSED
TESTING: gpio: 504: input direction PASSED
TESTING: gpio: 488: 0 PASSED
TESTING: gpio: 488 -> 504: 0 PASSED
TESTING: gpio: 488: 1 FAILED
TESTING: gpio: 488 -> 504: 1 FAILED
TESTING: gpio: 488: 0 PASSED
TESTING: gpio: 488 -> 504: 0 PASSED
It looks like the issue is that gc->bgpio_dir has changed its meaning.
It used to be set to the register value (so it was being inverted).
Now it's always set to 1 for output and 0 for input.
However the bgpio_get_set functions were not updated.
So they invert the bit again, which means a wrong register
is being accessed.
This patch fixes that by removing the unnecessary inversion.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio_set_config function creates a pinconf configuration for a given
pinc_config_param.
However, it always uses an arg of 0, which might not be a valid argument
for a given param. A good example of that would be the bias parameters,
where 0 means that the pull up or down resistor is null, and the pin is
directly connected to VCC/GND.
The framework uses in some other places the value 1 as a default argument
to enable the pull resistor, so let's use the same one here.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
clang warns about a tentative array definition in the gpio-omap driver:
drivers/gpio/gpio-omap.c:1282:34: error: tentative array definition assumed to have one element [-Werror]
static const struct of_device_id omap_gpio_match[];
It's best to just reorder the entire file to avoid forward declarations,
which lets us use the regular declaration. To do this, the unnecessary
CONFIG_OF check must also be removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Align the Kconfig formatting with the vast majority of the Kconfig
files, to make it a bit easier / more pleasant to read ;-)
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_free_hogs() was always called from gpiochip_remove(), not
of_gpiochip_remove(). It is now also called from the failure patch in
gpiochip_add_data_with_key().
Fixes: f625d46017 ("gpio: add GPIO hogging mechanism")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It turns out that one specific hardware has two direction
registers: one to set a GPIO line as input and another one
to set a GPIO line as output. So in theory a line can be
configured as input and output at the same time.
Make the MMIO GPIO helper deal with this: store both
registers in the state container, use both in the generic
code if present. Synchronize the input register to the
output register when we register a GPIO chip, with the
output settings taking precedence.
Keep the helper variable to detect inverted direction
semantics (only direction in register) but augment the
code to be more straight-forward for the generic case
when setting the registers.
Fix some flunky with unreadable direction registers at
the same time as we're touching this code.
Cc: David Woods <dwoods@mellanox.com>
Cc: Shravan Kumar Ramani <sramani@mellanox.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of debug and optional GPIO requested, the gpiod_put() is not aware of
and will WARN, which is not the case.
Make gpiod_put() NULL-aware to keep silent for optional GPIOs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
acpi_dev_get_first_match_name() is deprecated and going to be removed
because it leaks a reference.
Convert the driver to use acpi_dev_get_first_match_dev() instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch does the following bunch of changes:
- append () to the functions for reference
- convert gpiochip(s) -> GPIO chip(s)
- add a note about returned error code type [acpi_find_gpio()]
- move long summary to a description [acpi_gpio_count()]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- fix for a potential NULL-pointer dereference in the aspeed driver
- revert of the commit using the new gpio_set_config() when setting
debaunce and transitory state config as it caused a regression in
the aspeed driver
- two fixes for gpio-mockup for debugfs problems introduced in the
last merge window
-----BEGIN PGP SIGNATURE-----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=vIKK
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-rc3-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into fixes
gpio fixes for v5.1-rc3
- fix for a potential NULL-pointer dereference in the aspeed driver
- revert of the commit using the new gpio_set_config() when setting
debaunce and transitory state config as it caused a regression in
the aspeed driver
- two fixes for gpio-mockup for debugfs problems introduced in the
last merge window
Calling read() for a single byte read will return 2 currently. Use
simple_read_from_buffer() which correctly handles all sizes.
Fixes: 2a9e27408e ("gpio: mockup: rework debugfs interface")
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
If the call to of_gpiochip_scan_gpios() in of_gpiochip_add() fails, no
error handling is performed. This lead to the need of callers to call
of_gpiochip_remove() on failure, which causes "BAD of_node_put() on ..."
if the failure happened before the call to of_node_get().
Fix this by adding proper error handling.
Note that calling gpiochip_remove_pin_ranges() multiple times causes no
harm: subsequent calls are a no-op.
Fixes: dfbd379ba9 ("gpio: of: Return error if gpio hog configuration failed")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
"spi-cs-high" is going to be specified in child node of an SPI
controller's representing attached SPI device, so change the code to
look for it there, instead of checking parent node.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SPI GPIO device has more than just "cs-gpio" property in its node and
would request those GPIOs as a part of its initialization. To avoid
applying CS-specific quirk to all of them add a check to make sure
that propname is "cs-gpios".
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We are currently assuming all GPIOs are non-wakeup capable GPIOs as we
not configuring the bank->non_wakeup_gpios like we used to earlier with
platform_data.
Let's add omap_gpio_is_off_wakeup_capable() to make the handling clearer
while considering that later patches may want to configure SoC specific
bank->non_wakeup_gpios for the GPIOs in wakeup domain.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The bank->workaround_enabled should be for omap24xx erratum 1.101 but is not
needed any longer as erratum 1.101 handling only needs to happen based on
!bank->loses_context with patch "gpio: omap: Limit errata 1.101 handling to
wkup domain gpios only".
Further Grygorii Strashko <grygorii.strashko@ti.com> points out that we are
now tagging all edge GPIOs as non-wakeup GPIOs and rely on original erratum
1.101 handling for scacnning for edge interrupts that have triggered during
idle.
Also the TI Android kernel tree has an earlier commit "GPIO: OMAP: Always
scan gpios during runtime resume" by Tero Kristo <t-kristo@ti.com> saying:
"This allows the driver to generate interrupts for GPIOs that can't
wakeup but have changed state during runtime suspend. We cannot
depend on the decision based on no need to restore, as the system
state might change and pending events could gather up."
So let's remove bank->workaround_enabled and always scan for triggered edge
interrupts on resume. We do that based on bank->enabled_non_wakeup_gpios.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
We need to only apply errata 1.101 handling to clear non-wakeup edge gpios
for idle to the gpio bank(s) in the wkup domain to prevent spurious wake-up
events.
And we must restore what we did after idle manually as the gpio bank in
wkup domain is not restored otherwise.
Let's keep bank->saved_datain register reading separate, that's not related
to the 1.101 errata and is used separately on restore.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The debugfs read callback must advance ppos or users using read() on
the file descriptor will never get the EOL. This wasn't spotted before
as I was using busybox cat for testing which uses sendfile() internally
and only noticed it now when switched to cat from coreutils.
Fixes: 2a9e27408e ("gpio: mockup: rework debugfs interface")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This patch adds support for the GPIO controller used by Mellanox
BlueField SOCs.
Reviewed-by: David Woods <dwoods@mellanox.com>
Signed-off-by: Shravan Kumar Ramani <sramani@mellanox.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There is no need to include linux/init.h when at the same time
we include linux/module.h.
Remove redundant inclusion.
While here, sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
ACPI-enabled platforms can use this device via unified device
properties API. Convert driver to support this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In case devm_kzalloc, the patch returns ENOMEM to avoid potential
NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This function is needed in mcp23s08. That driver is a special snowflake
because it supports several hardware chips as a single "GPIO chip" under
Linux.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Phil Reid <preid@electromag.com.au>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The testing driver doesn't really depend on HAS_IOMEM. We may want to
build it for testing purposes on architectures not supporting IOMEM,
for example: on user-mode linux. Move it out of the "Memory Mapped GPIO
drivers" section.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The testing module doesn't need GPIO irqchip nor does it depend on
sysfs. Remove unnecessary dependencies from Kconfig.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Current code test wrong value so it does not verify if the written
data is correctly read back. Fix it.
Also make it return -EPERM if read value does not match written bit,
just like it done for adnp_gpio_direction_output().
Fixes: 5e969a401a ("gpio: Add Avionic Design N-bit GPIO expander support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
ida_simple_get may fail and return a negative error number.
The fix checks its return value; if it fails, go to err_destroy.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The ON Semiconductor CAT9554 is a variant of the PCA953x GPIO expander,
with 8 GPIOs and interrupt functionality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The code already defines "dev" variable to help with that, so make
sure all of the code uses it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Now that the driver's custom remove hook contains only a single
action, replace it by converting the code to use
devm_gpiochip_add_data() to simplify things.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Clk_gpio should be disabled in all error paths in the code that
follws, including the case when either gpiochip_add_data() or
gpiochip_irqchip_add() fail. To simplify things fix this by using
devm_add_action() to disable corresponding clock in case of any erros
as well as driver/device removal.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Clk_port should be disabled in all error paths in the code that
follws, including the case when either gpiochip_add_data() or
gpiochip_irqchip_add() fail. To simplify things fix this by using
devm_add_action_or_reset() to disable corresponding clock in case of
any erros as well as driver/device removal.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Both branches of the if statement do exactly the same thing, just at
different offsets. Simplify the code a bit by moving shared action
code outside of the if statement. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The only difference between two codepaths is register offset
used. Simplify the code a bit by replacing explicit calls with a
single call with a variable offset. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
-----BEGIN PGP SIGNATURE-----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=vf9L
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Use match_string() instead of reimplementing it (Andy Shevchenko)
- Enable SERR# forwarding for all bridges (Bharat Kumar Gogada)
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
- Fix DPC use of uninitialized data (Dongdong Liu)
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more
reliably (Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru
Gagniuc)
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
- Replace Douglas with Tom Joseph as Cadence PCI host/endpoint
maintainer (Lorenzo Pieralisi)
- Add DT support for R-Car RZ/G2E (R8A774C0) (Fabrizio Castro)
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo
Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of
open-coded reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
- Fix mvebu prefetchable BAR regression caused by common bridge
emulation that assumed all bridges had prefetchable windows (Thomas
Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
- Configure MPS settings for VMD root ports (Jon Derrick)
* tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI/LINK: Report degraded links via link bandwidth notification
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
PCI/PME: Fix possible use-after-free on remove
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
...
Core changes:
- The big change this time around is the irqchip handling in
the qualcomm pin controllers, closely coupled with the
gpiochip. This rework, in a classic fall-between-the-chairs
fashion has been sidestepped for too long. The Qualcomm
IRQchips using the SPMI and SSBI transport mechanisms have
been rewritten to use hierarchical irqchip. This creates
the base from which I intend to gradually pull support for
hierarchical irqchips into the gpiolib irqchip helpers to
cut down on duplicate code. We have too many hacks in the
kernel because people have been working around the missing
hierarchical irqchip for years, and once it was there,
noone understood it for a while. We are now slowly adapting
to using it. This is why this pull requests include changes
to MFD, SPMI, IRQchip core and some ARM Device Trees
pertaining to the Qualcomm chip family. Since Qualcomm have
so many chips and such large deployments it is paramount
that this platform gets this right, and now it (hopefully)
does.
- Core support for pull-up and pull-down configuration, also
from the device tree. When a simple GPIO chip support a
"off or on" pull-up or pull-down resistor, we provide a
way to set this up using machine descriptors or device tree.
If more elaborate control of pull up/down (such as
resistance shunt setting) is required, drivers should be
phased over to use pin control. We do not yet provide a
userspace ABI for this pull up-down setting but I suspect
the makers are going to ask for it soon enough. PCA953x
is the first user of this new API.
- The GPIO mockup driver has been revamped after some
discussion improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for
both testing and virtual prototyping, e.g. when you do
not yet have a GPIO expander to play with but really
want to get something to develop code around before
hardware is available. It's neat. The blackbox testing
usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating
flags.
- A new device core helper for devm_platform_ioremap_resource()
is funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped
I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum
driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers.
-----BEGIN PGP SIGNATURE-----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=VoVC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.1 cycle:
Core changes:
- The big change this time around is the irqchip handling in the
qualcomm pin controllers, closely coupled with the gpiochip. This
rework, in a classic fall-between-the-chairs fashion has been
sidestepped for too long.
The Qualcomm IRQchips using the SPMI and SSBI transport mechanisms
have been rewritten to use hierarchical irqchip. This creates the
base from which I intend to gradually pull support for hierarchical
irqchips into the gpiolib irqchip helpers to cut down on duplicate
code.
We have too many hacks in the kernel because people have been
working around the missing hierarchical irqchip for years, and once
it was there, noone understood it for a while. We are now slowly
adapting to using it.
This is why this pull requests include changes to MFD, SPMI,
IRQchip core and some ARM Device Trees pertaining to the Qualcomm
chip family. Since Qualcomm have so many chips and such large
deployments it is paramount that this platform gets this right, and
now it (hopefully) does.
- Core support for pull-up and pull-down configuration, also from the
device tree. When a simple GPIO chip supports an "off or on" pull-up
or pull-down resistor, we provide a way to set this up using
machine descriptors or device tree.
If more elaborate control of pull up/down (such as resistance shunt
setting) is required, drivers should be phased over to use pin
control. We do not yet provide a userspace ABI for this pull
up-down setting but I suspect the makers are going to ask for it
soon enough. PCA953x is the first user of this new API.
- The GPIO mockup driver has been revamped after some discussion
improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for both testing
and virtual prototyping, e.g. when you do not yet have a GPIO
expander to play with but really want to get something to develop
code around before hardware is available. It's neat. The blackbox
testing usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating flags.
- A new device core helper for devm_platform_ioremap_resource() is
funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers"
* tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (110 commits)
gpio: gpio-omap: fix level interrupt idling
gpio: amd-fch: Set proper output level for direction_output
x86: apuv2: remove unused variable
gpio: pca953x: Use PCA_LATCH_INT
platform/x86: fix PCENGINES_APU2 Kconfig warning
gpio: pca953x: Fix dereference of irq data in shutdown
gpio: amd-fch: Fix type error found by sparse
gpio: amd-fch: Drop const from resource
gpio: mxc: add check to return defer probe if clock tree NOT ready
gpio: ftgpio: Register per-instance irqchip
gpio: ixp4xx: Add DT bindings
x86: pcengines apuv2 gpio/leds/keys platform driver
gpio: AMD G-Series PCH gpio driver
drivers: depend on HAS_IOMEM for devm_platform_ioremap_resource()
gpio: tqmx86: Set proper output level for direction_output
gpio: sprd: Change to use SoC compatible string
gpio: sprd: Use SoC compatible string instead of wildcard string
gpio: of: Handle both enable-gpio{,s}
gpio: of: Restrict enable-gpio quirk to regulator-gpio
gpio: davinci: use devm_platform_ioremap_resource()
...
Tony notes that the GPIO module does not idle when level interrupts are
in use, as the wakeup appears to get stuck.
After extensive investigation, it appears that the wakeup will only be
cleared if the interrupt status register is cleared while the interrupt
is enabled. However, we are currently clearing it with the interrupt
disabled for level-based interrupts.
It is acknowledged that this observed behaviour conflicts with a
statement in the TRM:
CAUTION
After servicing the interrupt, the status bit in the interrupt status
register (GPIOi.GPIO_IRQSTATUS_0 or GPIOi.GPIO_IRQSTATUS_1) must be
reset and the interrupt line released (by setting the corresponding
bit of the interrupt status register to 1) before enabling an
interrupt for the GPIO channel in the interrupt-enable register
(GPIOi.GPIO_IRQSTATUS_SET_0 or GPIOi.GPIO_IRQSTATUS_SET_1) to prevent
the occurrence of unexpected interrupts when enabling an interrupt
for the GPIO channel.
However, this does not appear to be a practical problem.
Further, as reported by Grygorii Strashko <grygorii.strashko@ti.com>,
the TI Android kernel tree has an earlier similar patch as "GPIO: OMAP:
Fix the sequence to clear the IRQ status" saying:
if the status is cleared after disabling the IRQ then sWAKEUP will not
be cleared and gates the module transition
When we unmask the level interrupt after the interrupt has been handled,
enable the interrupt and only then clear the interrupt. If the interrupt
is still pending, the hardware will re-assert the interrupt status.
Should the caution note in the TRM prove to be a problem, we could
use a clear-enable-clear sequence instead.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[tony@atomide.com: updated comments based on an earlier TI patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current amd_fch_gpio_direction_output implementation ignores the value
argument, fix it so direction_output will set proper output level.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Enrico Weigelt <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit 0cdf21b34e
("gpio: pca953x: set the PCA_PCAL flag also when matching by DT")
introduces a helper macro which tells that chip supports latched interrupts,
but the macro was never used for ACPI or legacy enumeration.
So, make use of it for legacy and ACPI enumeration.
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We had again a busy development cycle with many new drivers as well as
lots of core improvements / cleanups. Let's go for highlights:
ALSA core:
- PCM locking scheme was refactored for reducing a global rwlock
- PCM suspend is handled in the device type PM ops now; lots of
explicit calls were reduced by this action
- Cleanups about PCM buffer preallocation calls
- Kill NULL device object in memory allocations
- Lots of procfs API cleanups
ASoC core:
- Support for only powering up channels that are actively being used
- Cleanups / fixes of topology API
ASoC drivers:
- MediaTek BTCVSD for a Bluetooth radio chip, which is the first such
driver we've had upstream!
- Quite a few improvements to simplify the generic card drivers,
especially the merge of the SCU cards into the main generic drivers
- Lots of fixes for probing on Intel systems to follow more standard
styles
- A big refresh and cleanup of the Samsung drivers
- New drivers: Asahi Kasei Microdevices AK4497, Cirrus Logic CS4341
and CS35L26, Google ChromeOS embedded controllers, Ingenic JZ4725B,
MediaTek BTCVSD, MT8183 and MT6358, NXP MICFIL, Rockchip RK3328,
Spreadtrum DMA controllers, Qualcomm WCD9335, Xilinx S/PDIF and PCM
formatters
ALSA drivers:
- Improvements of Tegra HD-audio controller driver for supporting new
chips
- HD-audio codec quirks for ALC294 S4 resume, ASUS laptop, Chrome
headset button support and Dell workstations
- Improved DSD support on USB-audio
- Quirk for MOTU MicroBook II USB-audio
- Support for Fireface UCX support and Solid State Logic Duende
Classic/Mini
-----BEGIN PGP SIGNATURE-----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=Vh8O
-----END PGP SIGNATURE-----
Merge tag 'sound-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"We had again a busy development cycle with many new drivers as well as
lots of core improvements / cleanups. Let's go for highlights:
ALSA core:
- PCM locking scheme was refactored for reducing a global rwlock
- PCM suspend is handled in the device type PM ops now; lots of
explicit calls were reduced by this action
- Cleanups about PCM buffer preallocation calls
- Kill NULL device object in memory allocations
- Lots of procfs API cleanups
ASoC core:
- Support for only powering up channels that are actively being used
- Cleanups / fixes of topology API
ASoC drivers:
- MediaTek BTCVSD for a Bluetooth radio chip, which is the first such
driver we've had upstream!
- Quite a few improvements to simplify the generic card drivers,
especially the merge of the SCU cards into the main generic drivers
- Lots of fixes for probing on Intel systems to follow more standard
styles
- A big refresh and cleanup of the Samsung drivers
- New drivers: Asahi Kasei Microdevices AK4497, Cirrus Logic CS4341
and CS35L26, Google ChromeOS embedded controllers, Ingenic JZ4725B,
MediaTek BTCVSD, MT8183 and MT6358, NXP MICFIL, Rockchip RK3328,
Spreadtrum DMA controllers, Qualcomm WCD9335, Xilinx S/PDIF and PCM
formatters
ALSA drivers:
- Improvements of Tegra HD-audio controller driver for supporting new
chips
- HD-audio codec quirks for ALC294 S4 resume, ASUS laptop, Chrome
headset button support and Dell workstations
- Improved DSD support on USB-audio
- Quirk for MOTU MicroBook II USB-audio
- Support for Fireface UCX support and Solid State Logic Duende
Classic/Mini"
* tag 'sound-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (461 commits)
ALSA: usb-audio: Add quirk for MOTU MicroBook II
ASoC: stm32: i2s: skip useless write in slave mode
ASoC: stm32: i2s: fix race condition in irq handler
ASoC: stm32: i2s: remove useless callback
ASoC: stm32: i2s: fix dma configuration
ASoC: stm32: i2s: fix stream count management
ASoC: stm32: i2s: fix 16 bit format support
ASoC: stm32: i2s: fix IRQ clearing
ASoC: qcom: Kconfig: fix dependency for sdm845
ASoC: Intel: Boards: Add Maxim98373 support
ASoC: rsnd: gen: fix SSI9 4/5/6/7 busif related register address
ALSA: firewire-motu: fix construction of PCM frame for capture direction
ALSA: bebob: use more identical mod_alias for Saffire Pro 10 I/O against Liquid Saffire 56
ALSA: hda: Extend i915 component bind timeout
ASoC: wm_adsp: Improve logging messages
ASoC: wm_adsp: Add support for multiple compressed buffers
ASoC: wm_adsp: Refactor compress stream initialisation
ASoC: wm_adsp: Reorder some functions for improved clarity
ASoC: wm_adsp: Factor out stripping padding from ADSP data
ASoC: cs35l36: Fix an IS_ERR() vs NULL checking bug
...
- Update the ACPICA code in the kernel to upstream revision 20190215
including ACPI 6.3 support and more:
* New predefined methods: _NBS, _NCH, _NIC, _NIH, and _NIG (Erik
Schmauss).
* Update of the PCC Identifier structure in PDTT (Erik Schmauss).
* Support for new Generic Affinity Structure subtable in SRAT
(Erik Schmauss).
* New PCC operation region support (Erik Schmauss).
* Support for GICC statistical profiling for MADT (Erik Schmauss).
* New Error Disconnect Recover notification support (Erik Schmauss).
* New PPTT Processor Structure Flags fields support (Erik Schmauss).
* ACPI 6.3 HMAT updates (Erik Schmauss).
* GTDT Revision 3 support (Erik Schmauss).
* Legacy module-level code (MLC) support removal (Erik Schmauss).
* Update/clarification of messages for control method failures
(Bob Moore).
* Warning on creation of a zero-length opregion (Bob Moore).
* acpiexec option to dump extra info for memory leaks (Bob Moore).
* More ACPI error to firmware error conversions (Bob Moore).
* Debugger fix (Bob Moore).
* Copyrights update (Bob Moore).
- Clean up sleep states support code in ACPICA (Christoph Hellwig).
- Rework in_nmi() handling in the APEI code and add suppor for the
ARM Software Delegated Exception Interface (SDEI) to it (James
Morse).
- Fix possible out-of-bounds accesses in BERT-related core (Ross
Lagerwall).
- Fix the APEI code parsing HEST that includes a Deferred Machine
Check subtable (Yazen Ghannam).
- Use DEFINE_DEBUGFS_ATTRIBUTE for APEI-related debugfs files
(YueHaibing).
- Switch the APEI ERST code to the new generic UUID API (Andy
Shevchenko).
- Update the MAINTAINERS entry for APEI (Borislav Petkov).
- Fix and clean up the ACPI EC driver (Rafael Wysocki, Zhang Rui).
- Fix DMI checks handling in the ACPI backlight driver and add the
"Lunch Box" chassis-type check to it (Hans de Goede).
- Add support for using ACPI table overrides included in built-in
initrd images (Shunyong Yang).
- Update ACPI device enumeration to treat the PWM2 device as "always
present" on Lenovo Yoga Book (Yauhen Kharuzhy).
- Fix up the enumeration of device objects with the PRP0001 device
ID (Andy Shevchenko).
- Clean up PPTT parsing error messages (John Garry).
- Clean up debugfs files creation handling (Greg Kroah-Hartman,
Rafael Wysocki).
- Clean up the ACPI DPTF Makefile (Masahiro Yamada).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=r6fU
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These are ACPICA updates including ACPI 6.3 support among other
things, APEI updates including the ARM Software Delegated Exception
Interface (SDEI) support, ACPI EC driver fixes and cleanups and other
assorted improvements.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20190215
including ACPI 6.3 support and more:
* New predefined methods: _NBS, _NCH, _NIC, _NIH, and _NIG (Erik
Schmauss).
* Update of the PCC Identifier structure in PDTT (Erik Schmauss).
* Support for new Generic Affinity Structure subtable in SRAT
(Erik Schmauss).
* New PCC operation region support (Erik Schmauss).
* Support for GICC statistical profiling for MADT (Erik Schmauss).
* New Error Disconnect Recover notification support (Erik
Schmauss).
* New PPTT Processor Structure Flags fields support (Erik
Schmauss).
* ACPI 6.3 HMAT updates (Erik Schmauss).
* GTDT Revision 3 support (Erik Schmauss).
* Legacy module-level code (MLC) support removal (Erik Schmauss).
* Update/clarification of messages for control method failures
(Bob Moore).
* Warning on creation of a zero-length opregion (Bob Moore).
* acpiexec option to dump extra info for memory leaks (Bob Moore).
* More ACPI error to firmware error conversions (Bob Moore).
* Debugger fix (Bob Moore).
* Copyrights update (Bob Moore)
- Clean up sleep states support code in ACPICA (Christoph Hellwig)
- Rework in_nmi() handling in the APEI code and add suppor for the
ARM Software Delegated Exception Interface (SDEI) to it (James
Morse)
- Fix possible out-of-bounds accesses in BERT-related core (Ross
Lagerwall)
- Fix the APEI code parsing HEST that includes a Deferred Machine
Check subtable (Yazen Ghannam)
- Use DEFINE_DEBUGFS_ATTRIBUTE for APEI-related debugfs files
(YueHaibing)
- Switch the APEI ERST code to the new generic UUID API (Andy
Shevchenko)
- Update the MAINTAINERS entry for APEI (Borislav Petkov)
- Fix and clean up the ACPI EC driver (Rafael Wysocki, Zhang Rui)
- Fix DMI checks handling in the ACPI backlight driver and add the
"Lunch Box" chassis-type check to it (Hans de Goede)
- Add support for using ACPI table overrides included in built-in
initrd images (Shunyong Yang)
- Update ACPI device enumeration to treat the PWM2 device as "always
present" on Lenovo Yoga Book (Yauhen Kharuzhy)
- Fix up the enumeration of device objects with the PRP0001 device ID
(Andy Shevchenko)
- Clean up PPTT parsing error messages (John Garry)
- Clean up debugfs files creation handling (Greg Kroah-Hartman,
Rafael Wysocki)
- Clean up the ACPI DPTF Makefile (Masahiro Yamada)"
* tag 'acpi-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (65 commits)
ACPI / bus: Respect PRP0001 when retrieving device match data
ACPICA: Update version to 20190215
ACPI/ACPICA: Trivial: fix spelling mistakes and fix whitespace formatting
ACPICA: ACPI 6.3: add GTDT Revision 3 support
ACPICA: ACPI 6.3: HMAT updates
ACPICA: ACPI 6.3: PPTT add additional fields in Processor Structure Flags
ACPICA: ACPI 6.3: add Error Disconnect Recover Notification value
ACPICA: ACPI 6.3: MADT: add support for statistical profiling in GICC
ACPICA: ACPI 6.3: add PCC operation region support for AML interpreter
efi: cper: Fix possible out-of-bounds access
ACPI: APEI: Fix possible out-of-bounds access to BERT region
ACPICA: ACPI 6.3: SRAT: add Generic Affinity Structure subtable
ACPICA: ACPI 6.3: Add Trigger order to PCC Identifier structure in PDTT
ACPICA: ACPI 6.3: Adding predefined methods _NBS, _NCH, _NIC, _NIH, and _NIG
ACPICA: Update/clarify messages for control method failures
ACPICA: Debugger: Fix possible fault with the "test objects" command
ACPICA: Interpreter: Emit warning for creation of a zero-length op region
ACPICA: Remove legacy module-level code support
ACPI / x86: Make PWM2 device always present at Lenovo Yoga Book
ACPI / video: Extend chassis-type detection with a "Lunch Box" check
..
* acpica:
ACPICA: Update version to 20190215
ACPI/ACPICA: Trivial: fix spelling mistakes and fix whitespace formatting
ACPICA: ACPI 6.3: add GTDT Revision 3 support
ACPICA: ACPI 6.3: HMAT updates
ACPICA: ACPI 6.3: PPTT add additional fields in Processor Structure Flags
ACPICA: ACPI 6.3: add Error Disconnect Recover Notification value
ACPICA: ACPI 6.3: MADT: add support for statistical profiling in GICC
ACPICA: ACPI 6.3: add PCC operation region support for AML interpreter
ACPICA: ACPI 6.3: SRAT: add Generic Affinity Structure subtable
ACPICA: ACPI 6.3: Add Trigger order to PCC Identifier structure in PDTT
ACPICA: ACPI 6.3: Adding predefined methods _NBS, _NCH, _NIC, _NIH, and _NIG
ACPICA: Update/clarify messages for control method failures
ACPICA: Debugger: Fix possible fault with the "test objects" command
ACPICA: Interpreter: Emit warning for creation of a zero-length op region
ACPICA: Remove legacy module-level code support
ACPICA: Get rid of acpi_sleep_dispatch()
ACPICA: Update version to 20190108
ACPICA: All acpica: Update copyrights to 2019
ACPICA: acpiexec: Add option to dump extra info for memory leaks
ACPICA: Convert more ACPI errors to firmware errors
If a PCA953x gpio was used as an interrupt and then released,
the shutdown function was trying to extract the pca953x_chip
pointer directly from the irq_data, but in reality was getting
the gpio_chip structure.
The net effect was that the subsequent writes to the data
structure corrupted data in the gpio_chip structure, which wasn't
immediately obvious until attempting to use the GPIO again in the
future, at which point the kernel panics.
This fix correctly extracts the pca953x_chip structure via the
gpio_chip structure, as is correctly done in the other irq
functions.
Fixes: 0a70fe00ef ("gpio: pca953x: Clear irq trigger type on irq shutdown")
Cc: stable@vger.kernel.org
Signed-off-by: Mark Walton <mark.walton@serialtek.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The build servers and linux-next are complaining like this:
drivers/gpio/gpio-amd-fch.c: In function 'amd_fch_gpio_probe':
drivers/gpio/gpio-amd-fch.c:164:49: warning: passing argument 2 of
'devm_ioremap_resource' discards 'const' qualifier from pointer
target type [-Wdiscarded-qualifiers]
priv->base = devm_ioremap_resource(&pdev->dev, &amd_fch_gpio_iores);
^~~~~~~~~~~~~~~~~~~
In file included from include/linux/platform_device.h:14, from
drivers/gpio/gpio-amd-fch.c:15:
include/linux/device.h:709:15: note: expected 'struct resource *'
but argument is of type 'const struct resource *'
void __iomem *devm_ioremap_resource(struct device *dev,struct resource *res);
^~~~~~~~~~~~~~~~~~~~~
Let's just remove "const" for now.
It is possible that devm_ioremap_resource() should rather
be constified so we can pass const resources as arguments.
But right now I just want to get rid of this build warning.
Fixes: e09d168f13 ("gpio: AMD G-Series PCH gpio driver")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Cc: Enrico Weigelt <info@metux.net>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On i.MX8MQ platform, clock driver uses platform driver
model and it is probed after GPIO driver, so when GPIO
driver fails to get clock, it should check the error type
to decide whether to return defer probe or just ignore
the clock operation.
Fixes: 2808801aab ("gpio: mxc: add clock operation")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
