Rather than having each platform class provide a mach/smp.h header for
smp_cross_call(), arrange for them to register the function with the
core ARM SMP code instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It shows up on the console despite using "silent" in the bootargs, and
it's really just noise in the boot log since PM init is always called.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: jhnikula@gmail.com
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
The achievable power modes of the power domains in cpuidle
depends on the system wide 'enable_off_mode' knob in debugfs.
Upon changing enable_off_mode, do not change the C-states
'valid' field but instead dynamically restrict the power modes
when entering idle.
The C-states 'valid' field is just used to enable/disable some
C-states at init and shall not be changed later on.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
- fix single and multi-lines comments format
- removed the omap3_idle_bm_check function and replaced the test
in omap3_enter_idle_bm by the equivalent code
- re-organize omap3_enter_idle_bm code path, assign local variables
only when needed
- reword some comments
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The current implementation defines an internal structure and a
C-states array. Using those structures is redundant to the
structs used by the cpuidle framework.
This patch provides a clean-up of the internal struct, removes the
internal C-states array, stores the data using the existing cpuidle
per C-state struct and registers the mach specific data to cpuidle
C-state driver_data (accessed using cpuidle_[gs]et_statedata).
Also removes unused macros, fields and code and compacts the repeating
code using an inline helper function.
The result is more compact and more readable code as well as
reduced data RAM usage.
Also retain C1 as the only always valid C-state and system safe state.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
- sleep_latency and wake_latency are not used, replace them by
exit_latency which is used by cpuidle. exit_latency simply is
the sum of sleep_latency and wake_latency,
- replace threshold by target_residency,
- changed the OMAP3 specific cpuidle code accordingly,
- changed the OMAP3 board code accordingly.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The cpuidle states settings can be overriden by some board-
specific settings, by calling omap3_pm_init_cpuidle.
Remove the 3430SDP specific states settings registration
since the figures are identical to the default ones (in cpuidle34xx.c).
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Powerdown the internal UTMI PHY when USB is not enabled. This will
allow the OMAP core domain to transition to retention and offmode.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
omap4430_phy_init() function can be called with no device pointer,
to powerdown the PHY during board init when USB is disabled.
Fix the function accordingly.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Powerdown the internal PHY during board init for OMAP44xx.
So that when musb is disabled core transition to retention/off
is not blocked.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
* power-domains:
PM: Fix build issue in clock_ops.c for CONFIG_PM_RUNTIME unset
PM: Revert "driver core: platform_bus: allow runtime override of dev_pm_ops"
OMAP1 / PM: Use generic clock manipulation routines for runtime PM
PM / Runtime: Generic clock manipulation rountines for runtime PM (v6)
PM / Runtime: Add subsystem data field to struct dev_pm_info
OMAP2+ / PM: move runtime PM implementation to use device power domains
PM / Platform: Use generic runtime PM callbacks directly
shmobile: Use power domains for platform runtime PM
PM: Export platform bus type's default PM callbacks
PM: Make power domain callbacks take precedence over subsystem ones
Add IGEP3 machine support to board-igep0020
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
to allow easy addition of IGEP3
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IGEP2 and IGEP3 boards are very similar and can be merged into one file.
Start refactoring with changing igep2 to igep where applicable.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use generic irq chip for omap2 & 3.
Note that this patch also leaves out the spurious IRQ warning
for omap3.
This warning should no longer be needed as the interrupt handlers
for various devices have implemented the necessayr read-back of
the posted write.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The debug l3_ick/rate is not displaying the actual rate of the clock in
hardware. This is because, the core dpll set_rate function doesn't update the
clk.rate. After fixing, the l3_ick/rate is displaying proper values.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Wamsley <paul@pwsan.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
use gpio_request_<one|array>() instead of multiple gpiolib calls,
remove unneeded variables, etc.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, omap_display_init() maintains arrays for hwmod name(oh_name) and the
correspnding platform_device name(dev_name) needed by omap_device_build().
A variable oh_count keeps a track of the number of devices to build from oh_name
based on what omap revision it is.
Clean this up by maintaining an array of omap_dss_hwmod_data struct which is
defined for each omap revision as suggested by Tomi Valkeinen. Assign the
corresponding omap_dss_hwmod_data array struct to the pointer curr_dss_hwmod in
omap_display_init().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move some of the configurable HDMI PLL parameters to dssdev.clock struct.
Cleanup the function hdmi_compute_pll() by using the parameters defined in the
board file and do some cosmetic modifications.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/panel-generic-dpi.h is an include for
the OMAP DSS panel driver for generic DPI displays. A more logical place
for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Most boards use exactly the same configuration for musb initialization.
Create a default that can be shared amount different boards.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
and reduce amount of copy/paste
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
CC: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introduce omap_pmic_init that registers i2c bus and PMIC device on that
bus and add omap2/3/4 wrappers for common cases.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add common-board-devices.c that will contain the code for peripheral
devices initializatoin shared between multiple boards.
Start small with touchscreen initialization.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
cat of debugfs entry for vp_volt provides voltage. The additional pr_notice
is just spam on console and provides no additional information.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
pm44xx.c is built only when CONFIG_PM is setup,
remove redundant CONFIG_PM check.
This also fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=25022
Reported-by: Martin Etti <ettl.martin@gmx.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If the probe fails, the node should be deleted from sr_list.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We are releasing the memory region, but never actually request it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
sr_late_init() will take care of freeing the resources.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Removing extra lines, spaces and unneeded parenthesis.
Collapsing an if statement to detect the type of error.
l3_smx:
- Fixing the message printed on error.
So now: looks like:
"No Error Error seen..." "No Error seen..."
"In-Band Error Error seen..." "In-Band Error seen..."
Other messages are self explanatory, no "Error" added to them.
(E.g.: "Address Hole seen...")
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
l3_smx:
- Add missing free_irq and remove an empty goto label.
l3_noc:
- If kzalloc fails driver shouldn't continue with a NULL pointer.
- Add missing free_irq and remove empty goto labels.
- Safe to assume that if we reached the end point of execution
without errors, then return value is 0, so replacing instead
another goto.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In commit 7538e3db6e (PM: add support
for device power domains) a better way for handling platform-specific
power hooks was introduced.
Rather than using the platform_bus dev_pm_ops overrides
(platform_bus_set_pm_ops()), this patch moves the OMAP runtime PM
implementation over to using device power domains.
Since OMAP is the only user of platform_bus_set_pm_ops(), that
interface can be removed (and will be in a forthcoming patch.)
[rjw: Rebased on top of a previous change modifying the handling of
power domains by the PM core so that power domain callbacks take
precendence over subsystem-level PM callbacks.]
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Blindly setting 1.2V in the initial structure may not even match the
default voltages stored in the voltage table which are supported for
the domain. For example, OMAP3430 core domain does not use 1.2V and
ends up generating a warning on the first transition.
Further, since omap2_set_init_voltage is called as part of the pm
framework's initialization sequence to configure the voltage required
for the current OPP, the call does(and has to) setup the system
voltage(curr_volt as a result) using the right mechanisms appropriate
for the system at that point of time. This also overrides
initialization we are currently doing in voltage.c making it
redundant. So, remove the wrong and redundant initialization.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 has two different Devices IVA and DSP. DSP is bound
with IVA for DVFS. The registration of IVA dev in API
'omap2_init_processor_devices' was missing. Init dev for
'iva_dev' is added.
This also fixes the following error seen during boot as
omap2_set_init_voltage can now find the iva device
omap2_set_init_voltage: Invalid parameters!
omap2_set_init_voltage: Unable to put vdd_iva to its init voltage
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
So that omap_vram_set_sdram_vram() is called before
omap_vram_reserve_sdram_memblock().
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If an error occurs in the L3 on any other initiator than MPU,
the interrupt goes unhandled given that the 'base' register
was calculated with the initialized err_source value (which
coincidentally points to MPU) and not with the actual source
of the error.
Removed parenthesis that are not needed for the touched lines.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes broken build when using binutils 2.21.
Signed-off-by: Oskar Andero <oskar.andero@sonyericsson.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO module expects the debounce clocks to be enabled during reset. It doesn't
reset properly and timeouts are seen, if this clock isn't enabled during
reset. Add the HWMOD_CONTROL_OPT_CLKS_IN_RESET flags to the GPIO HWMODs, with
which the debounce clocks are enabled during reset.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
As per OMAP3 erratum (i671), ROM code adds extra latencies while
restoring CM_AUTOIDLE_PLL register, if AUTO_PERIPH_DPLL is equal to 1.
This patch stores 0's in scratchpad content area corresponding to
AUTO_PERIPH_DPLL, to prevent ROM code to try to lock per DPLL, since
it won't respect proper programing scheme.
This register is then stored in prcm context. The saving and restore
is now done by kernel side.
Here follow the erratum description
DESCRIPTION
After OFF mode transition, among many restorations, the ROM Code restores the
CM_AUTOIDLE_PLL register, and after that, it tries to relock the PER DPLL.
In case the restoration data stored in scratchpad memory contains a field
CM_AUTOIDLE_PLL.AUTO_PERIPH_DPLL = 1, then the way the ROM Code restores and
locks the PER DPLL does not respect the PER DPLL programming scheme.
In that case, the DPLL might not lock. Meanwhile, when trying to lock the PER
DPLL, the ROM Code does not hang. Only extra latencies are introduced at
wake-up.
WORKAROUND
When saving the context-restore structure in scratchpad memory, in order to
respect the PER DPLL programming scheme, it is advised to store 0 in the
CM_AUTOIDLE_PLL.AUTO_PERIPH_DPLL field of the saved structure.
After wake-up, the application should store in CM_AUTOIDLE_PLL register the
right desired value.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The saving of CCR.CM_AUTOIDLE_PLL is done in scratchpad area.
However, in current code, the saving is done for CM_AUTOIDLE2_PLL
(offset 0x34) instead of CM_AUTOIDLE_PLL (offset 0x30).
This patch changes the code to save the correct register.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DSS driver has used fck and ick clocks on OMAP2/3 to get DSS HW up and
running, and also to get the pixel clock's source clock rate from the
fck.
On OMAP4 the clock data is set up in a different way, as there's no ick,
dss_fck points to a fake clock which just affects DSS's MODULEMODE, and
dss_dss_clk if the DSS_FCK.
>From DSS driver's point of view the dss_fck sounds like an ick, and
dss_dss_clk is the fck. While this is not entirely correct from HW point
of view, especially for the ick, configuring the clock aliases that way
makes DSS "just work" with OMAP4's clock setup.
In the (hopefully near) future DSS driver will be reworked to use
pm_runtime support which should clean up the clock code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Convert boards that use SMSC911x to use gpmc-smsc911x.
Also allocate struct platform_device dynamically.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: folded in a fix from Igor Grindberg]
Signed-off-by: Tony Lindgren <tony@atomide.com>
SMSC911x devices attached to OMAP GPMC always use low level irqs.
Setting the appropriate flag in the irq resourse strucure allows using
.flags field in the omap_smsc911x_platform_data for driver specific
flags
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The isp1704 usb tranceiver is used for charging and can be
disabled when not in use. Provide the powering routine to
the driver via platform data.
Also changed the indent of ".name" variable in rx51_charger_device
definition to use tabs same way as the new ".dev" variable indent.
Put this in the same patch since the indent fix is only needed
when there are multiple members in the struct definition.
Loosely based on earlier patches from Heikki Krogerus in
Nokia N900 maemo kernel.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Acked-By: Heikki Krogerus <heikki.krogerus@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
OMAP2420, 2430 and 3xxx were using the OMAP4 end address
that unfortunately is not located at the same base address.
Moreover the OMAP4 size was set to 256 instead of 4096.
Change all .pa_end to set them to .pa_start + 0xfff
Cc: "G, Manjunath Kondaiah" <manjugk@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Reported-by: Michael Fillinger <m-fillinger@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Header files in arch/arm/*/include/mach included from
arch/arm/include/asm/*.h are there to provide necessary definitions for
either the rest of the kernel or the ARM specific parts. They shouldn't
be polluted with *any* platform private stuff which is not absolutely
necessary to satisfy the rest of the kernel.
Hence move the OMAP specific SMP boot functions to different header
instead of keeping them in 'plat/smp.h' which gets included indirectly
by linux/smp.h
The patch is outcome of the discussion in below thread:
http://www.spinics.net/lists/arm-kernel/msg120363.html
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (442 commits)
[media] videobuf2-dma-contig: make cookie() return a pointer to dma_addr_t
[media] sh_mobile_ceu_camera: Do not call vb2's mem_ops directly
[media] V4L: soc-camera: explicitly require V4L2_BUF_TYPE_VIDEO_CAPTURE
[media] v4l: soc-camera: Store negotiated buffer settings
[media] rc: interim support for 32-bit NEC-ish scancodes
[media] mceusb: topseed 0x0011 needs gen3 init for tx to work
[media] lirc_zilog: error out if buffer read bytes != chunk size
[media] lirc: silence some compile warnings
[media] hdpvr: use same polling interval as other OS
[media] ir-kbd-i2c: pass device code w/key in hauppauge case
[media] rc/keymaps: Remove the obsolete rc-rc5-tv keymap
[media] remove the old RC_MAP_HAUPPAUGE_NEW RC map
[media] rc/keymaps: Rename Hauppauge table as rc-hauppauge
[media] rc-rc5-hauppauge-new: Fix Hauppauge Grey mapping
[media] rc-rc5-hauppauge-new: Add support for the old Black RC
[media] rc-rc5-hauppauge-new: Add the old control to the table
[media] rc-winfast: Fix the keycode tables
[media] a800: Fix a few wrong IR key assignments
[media] opera1: Use multimedia keys instead of an app-specific mapping
[media] dw2102: Use multimedia keys instead of an app-specific mapping
...
Fix up trivial conflicts (remove/modify and some real conflicts) in:
arch/arm/mach-omap2/devices.c
drivers/staging/Kconfig
drivers/staging/Makefile
drivers/staging/dabusb/dabusb.c
drivers/staging/dabusb/dabusb.h
drivers/staging/easycap/easycap_ioctl.c
drivers/staging/usbvideo/usbvideo.c
drivers/staging/usbvideo/vicam.c
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (35 commits)
ARM: Update (and cut down) mach-types
ARM: 6771/1: vexpress: add support for multiple core tiles
ARM: 6797/1: hw_breakpoint: Fix newlines in WARNings
ARM: 6751/1: vexpress: select applicable errata workarounds in Kconfig
ARM: 6753/1: omap4: Enable ARM local timers with OMAP4430 es1.0 exception
ARM: 6759/1: smp: Select local timers vs broadcast timer support runtime
ARM: pgtable: add pud-level code
ARM: 6673/1: LPAE: use phys_addr_t instead of unsigned long for start of membanks
ARM: Use long long format when printing meminfo physical addresses
ARM: integrator: add Integrator/CP sched_clock support
ARM: realview/vexpress: consolidate SMP bringup code
ARM: realview/vexpress: consolidate localtimer support
ARM: integrator/versatile: consolidate FPGA IRQ handling code
ARM: rationalize versatile family Kconfig/Makefile
ARM: realview: remove old AMBA device DMA definitions
ARM: versatile: remove old AMBA device DMA definitions
ARM: vexpress: use new init_early for clock tree and sched_clock init
ARM: realview: use new init_early for clock tree and sched_clock init
ARM: versatile: use new init_early for clock tree and sched_clock init
ARM: integrator: use new init_early for clock tree init
...
In Blaze and Panda, 32KHz clock - CLK32KG to WLAN is supplied
from Phoenix TWL6030.
Add CLK32KG platform data to blaze and omap4panda board file.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Make sure the kernel can be compiled with both OMAP2 and OMAP3 camera
support linked in, and give public symbols proper omap2/omap3 prefixes.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The omap3isp platform device requires platform data. Instead of
registering the device in omap2_init_devices(), export an
omap3_init_camera() function to fill the device structure with the
platform data pointer and register the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new/changed base address definitions and resources for
OMAP3630 ISP.
The OMAP3430 CSI2PHY block is same as the OMAP3630 CSIPHY2
block. But the later name is chosen as it gives more symmetry
to the names.
Signed-off-by: Tuukka Toivonen <tuukkat76@gmail.com>
Signed-off-by: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit db97eb7dfe
(omap: gpmc: enable irq mode in gpmc) enabled interrupts for
GPMC (General Purpose Memory Controller). However, looks like
this patch only works on omap3. Fix the issues to avoid warnings
on omap4 during the boot.
GPMC: number of chip select is 8, CS0 to CS7. One less IRQ
allocated throws below warning at boot:
[ 0.429290] Trying to install type control for IRQ409
[ 0.429290] Trying to set irq flags for IRQ409
Resolve following warning messages in boot when irq chip is not set:
[ 0.429229] Trying to install interrupt handler for IRQ402
[ 0.429229] Trying to install interrupt handler for IRQ403
[ 0.429229] Trying to install interrupt handler for IRQ404
[ 0.429260] Trying to install interrupt handler for IRQ405
[ 0.429260] Trying to install interrupt handler for IRQ406
[ 0.429260] Trying to install interrupt handler for IRQ407
[ 0.429290] Trying to install interrupt handler for IRQ408
Resolve following warning in OMAP4:
[ 0.429290] gpmc: irq-20 could not claim: err -22
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: combined patches into one, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
the pandaboard does not use the VUSIM or VAUX1 power regulators on the TWL6030
and are left floating. if the VUSIM and VAUX1 power regulators are initilized,
noise on the unloaded regulators generates an overcurrent interrupt causing the
system to power down. this patch removes the initialization of the unused power
regulators of VUSIM and VAUX1.
Signed-off-by: David Anders <x0132446@ti.com>
Acked-by: Andy Green <andy.green@linaro.org>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The handler function may be called from the point it is registered.
Since the handler inspects IRQ numbers, we must set them up before
registration.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the return value for the successful case.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding DVI support to OMAP4 PandaBoard.
PandaBoard uses TFP410 DVI Framer chip
http://focus.ti.com/lit/ds/symlink/tfp410.pdf
The TFP410 gets its power enable and display data over GPIO lines muxed
in from OMAP4430. PandaBoard supports other LCD displays through
expansion
connectors, following board rework. This will disable the DVI interface.
However, the existing mux settings remain the same
PandaBoard additionally supports display over HDMI interface. It is
mutually exclusive to display over DVI. Hence the mux settings need to
be
configured seperately, as and when HDMI is enabled
Also, I2C3 bus used for reading EDID data from DVI Monitors is
registered here. Since the design is similar to BeagleBoard, the code
for the same is taken from the kernel.org commit e3333f48dd
(omap: Adding beagle i2c eeprom driver to read EDID)
Reviewed-by: Manjunath G Kondaiah <manjugk@ti.com>
Reviewed-by: Anand Gadiyar <gadiyar@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
[tomi.valkeinen@ti.com: fixed conflicts with HDMI]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (91 commits)
ARM: 6806/1: irq: introduce entry and exit functions for chained handlers
ARM: 6781/1: Thumb-2: Work around buggy Thumb-2 short branch relocations in gas
ARM: 6747/1: P2V: Thumb2 support
ARM: 6798/1: aout-core: zero thread debug registers in a.out core dump
ARM: 6796/1: Footbridge: Fix I/O mappings for NOMMU mode
ARM: 6784/1: errata: no automatic Store Buffer drain on Cortex-A9
ARM: 6772/1: errata: possible fault MMU translations following an ASID switch
ARM: 6776/1: mach-ux500: activate fix for errata 753970
ARM: 6794/1: SPEAr: Append UL to device address macros.
ARM: 6793/1: SPEAr: Remove unused *_SIZE macros from spear*.h files
ARM: 6792/1: SPEAr: Replace SIZE macro's with SZ_4K macros
ARM: 6791/1: SPEAr3xx: Declare device structures after shirq code
ARM: 6790/1: SPEAr: Clock Framework: Rename usbd clock and align apb_clk entry
ARM: 6789/1: SPEAr3xx: Rename sdio to sdhci
ARM: 6788/1: SPEAr: Include mach/hardware.h instead of mach/spear.h
ARM: 6787/1: SPEAr: Reorder #includes in .h & .c files.
ARM: 6681/1: SPEAr: add debugfs support to clk API
ARM: 6703/1: SPEAr: update clk API support
ARM: 6679/1: SPEAr: make clk API functions more generic
ARM: 6737/1: SPEAr: formalized timer support
...
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (172 commits)
USB: Add support for SuperSpeed isoc endpoints
xhci: Clean up cycle bit math used during stalls.
xhci: Fix cycle bit calculation during stall handling.
xhci: Update internal dequeue pointers after stalls.
USB: Disable auto-suspend for USB 3.0 hubs.
USB: Remove bogus USB_PORT_STAT_SUPER_SPEED symbol.
xhci: Return canceled URBs immediately when host is halted.
xhci: Fixes for suspend/resume of shared HCDs.
xhci: Fix re-init on power loss after resume.
xhci: Make roothub functions deal with device removal.
xhci: Limit roothub ports to 15 USB3 & 31 USB2 ports.
xhci: Return a USB 3.0 hub descriptor for USB3 roothub.
xhci: Register second xHCI roothub.
xhci: Change xhci_find_slot_id_by_port() API.
xhci: Refactor bus suspend state into a struct.
xhci: Index with a port array instead of PORTSC addresses.
USB: Set usb_hcd->state and flags for shared roothubs.
usb: Make core allocate resources per PCI-device.
usb: Store bus type in usb_hcd, not in driver flags.
usb: Change usb_hcd->bandwidth_mutex to a pointer.
...
Adding board file structure for display which adds the display
structure with HDMI as the default driver when the display init
is called.
HDMI GPIO configurations are also done in this file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adding board file structure for display which adds the display
structure with HDMI as the default driver when the display init
is called.
HDMI GPIO configurations are also done in this file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The wl1271's irq line is completely controlled by the 1271 device, and
the host does not not need to pull it up.
While there's no functional effect, letting the host pull this line up is
just redundant, and wastes power.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adapts the register offsets used to read the CPU DIE ID registers
when run on 44XX so they match what is in the OMAP4430 Reference Manual
page 269
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove duplicate mux modes to make the binary smaller:
text data bss dec hex filename
9378 24472 0 33850 843a mux44xx.o
9378 19104 0 28482 6f42 mux44xx.o
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add macro for defining static pins in the board file.
We can now start implementing pin multiplexing in the platform init
code for devices that call omap_hwmod_mux_init. Currently that is
only implemented for serial.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently OMAP_DEVICE_PAD_IDLE flag is used to mux pins
dynamically. This can be simplified by using the enabled
state variable of each pad. This also fixes the issue of
the static pads not getting muxed after idling and
disable/enable state transitions.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This avoids going through the list unnecessarily when
idling devices for runtime PM.
Based on an earlier patch by sricharan <r.sricharan@ti.com>.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch adds the new power management trace points for
the OMAP architecture.
The trace points are for:
- default idle handler. Since the cpuidle framework is
instrumented in the generic way there is no need to
add trace points in the OMAP specific cpuidle handler;
- SoC clocks changes (enable, disable, set_rate),
- power domain states: the desired target state and -if different-
the actually hit state.
Because of the generic nature of the changes, OMAP3 and OMAP4 are supported.
Tested on OMAP3 with suspend/resume, cpuidle, basic DVFS.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This Patch adds OPP enteries for IVA in OMAP4 OPP Table
Tested on OMAP4430 SDP Board.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Almost all OMAP4 boards support OPP 800 MHz and OPP 1 GHz.
Enable them in OPP Table. For small minority of boards which use
OMAP4430-800 MHz device OPP 1GHz is not supported,
OPP 1GHz should be disabled from board file.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Since all voltage data is now centralized in oppxxx_data.c, we can replace
the values in the opp table with the macros used for voltage values.
This will avoid opp table and voltage layer having conflicting values.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds support for the standard push buttons available on
Overo expansion boards.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds support for the standard LEDs on the Overo COM and expansion boards
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The ads7846 driver now requires a regulator. This patch adds the
necessary regulator to the overo board file. Without it, the
following error occurs (and the touchscreen will not function):
ads7846 spi1.0: unable to get regulator: -19
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds DSS2 support for DVI, S-video, the 480x272 Samsung
LTE430WQ-F0C panel, and the 320x240 LG.Philips LB035Q02 panel.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Provide a function in pdata to allow dss submodules to check if a given
clock is available on a platform as an optional clock.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
(based on implementation from Senthil)
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, the core DSS platform device requests for an irq line for OMAP2 and
OMAP3. Make DISPC and DSI platform devices request for a shared IRQ line.
On OMAP3, the logical OR of DSI and DISPC interrupt lines goes to the MPU. There
is a register DSS_IRQSTATUS which tells if the interrupt came from DISPC or DSI.
On OMAP2, there is no DSI, only DISPC interrupts goto the MPU. There is no
DSS_IRQSTATUS register.
Hence, it makes more sense to have separate irq handlers corresponding to the
DSS sub modules instead of having a common handler.
Since on OMAP3 the logical OR of the lines goes to MPU, the irq line is shared
among the IRQ handlers.
The hwmod irq info has been removed for DSS to DISPC and DSI for OMAP2 and OMAP3
hwmod databases. The Probes of DISPC and DSI now request for irq handlers.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS code uses ick as one of the clocks in clk_get/clk_put. OMAP4 clock database
doesn't have ick for DSS, so adding ick as dummy clock.
This is needed for backward compatibility with OMAP2/3.
Once pm_runtime* APIs get introduced in DSS, this will be revisited.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, clock database has <dev, clock-name> tuples for DSS2. Because of
this, the clock names are different across different OMAP platforms.
This patch aligns the DSS2 clock names and roles across OMAP 2420, 2430, 3xxx,
44xx platforms in the clock databases, hwmod databases for opt-clocks, and DSS
clock handling.
This ensures that clk_get/put/enable/disable APIs in DSS can use uniform role
names.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for DSI is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.
Also, vdds_dsi regulator handling is copied to dsi.c, since vdds_dsi regulator is
needed by dpi_init() too. Board files are updated accordingly to add 2 instances of
vdds_dsi regulator.
DSI platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for VENC is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.
Also, venc_vdda_dac reading is moved to venc.c.
VENC platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All clock management is moved to dss platform driver. clk_get/put APIs use
dss device instead of core platform device.
Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So the device name is changed from omapdss to omapdss_dss in 2420, 2430,
3xxx clock database files. Now the core driver "omapdss" only takes care
of panel registration with the custom bus.
core driver also uses the clk_enable() / clk_disable() APIs exposed by DSS for
clock management.
DSS driver would do clock management of clocks needed by DISPC, RFBI, DSI, VENC
TODO: The clock content would be adapted to omap_hwmod in a seperate series.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Looks up the hwmod database for each of the given DSS HW IP and builds
omap_device which inturn does the platform device register for each of DSS HW IP
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HW superwised smart idle for wdtimer in OMAP3 prevents
CORE power domain idle transitions. Disable it by swithing
to SW supervised transitions.
This could be a hardware bug in the OMAP3 wdtimer2 block.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
This is a first pass at reorganizing mach-omap2/voltage.c:
- Separate almost all of the data from the code of mach-omap2/voltage.c.
The code remains in mach-omap2/voltage.c. The data goes into one
of several places, depending on what type of data it is:
- Silicon process/validation data: mach-omap2/opp*_data.c
- VC (Voltage Controller) data: mach-omap2/vc*_data.c
- VP (Voltage Processor) data: mach-omap2/vp*_data.c
- Voltage domain data: mach-omap2/voltagedomains*_data.c
The ultimate goal is for all this data to be autogenerated, the same
way we autogenerate the rest of our data.
- Separate VC and VP common data from VDD-specific VC and VP data.
- Separate common voltage.c code from SoC-specific code; reuse common code.
- Reorganize structures to avoid unnecessary memory loss due to unpacked
fields.
There is much left to be done. VC code and VP code should be separated out
into vc*.c and vp*.c files. Many fields in the existing structures are
superfluous, and should be removed. Some code in voltage.c seems to be
duplicated; that code should be moved into functions of its own. Proper
voltage domain code should be created, as was done with the powerdomain
and clockdomains, and powerdomains should reference voltagedomains.
Thanks to Shweta Gulati <shweta.gulati@ti.com> for comments. Thanks
to Rajendra Nayak <rnayak@ti.com> for finding and fixing some bugs
that prevented OMAP4 from booting:
https://patchwork.kernel.org/patch/587311/
His patch has been folded into this one to avoid breaking OMAP4
between patches. Thanks also to Kevin Hilman <khilman@ti.com> for
finding and fixing a compile problem when !CONFIG_PM:
http://www.spinics.net/lists/arm-kernel/msg118067.html
His patch has also been folded into this one to avoid breaking
!CONFIG_PM builds.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Shweta Gulati <shweta.gulati@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
On the newer ARM processors like CortexA8, CortexA9, the caches can be
speculatively loaded while they are getting flushed.
Clear the SCTLR C bit to prevent further data cache allocation as
part of cache clean routine
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The current code saves few un-necessary registers which are read-only or
write-only, unused CP15 registers.
Remove them and keep only necessary CP15 registers part of
low power context save/restore.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
When L1 cache is suppose to be lost, it needs to be cleaned before
entrering to the low power mode.
While at this, also fix few comments and remove un-necessary
clean_l2 lable.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add necessary barriers after enabling MMU. Also use the sane way to
load pc and jump to it instead of executing ldma first up.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On ARMv7 dsb, dmb instructions are supported and can be used directly
instead of their cp15 equivalnet. Also remove the opcodes for smc
and use the available instruction directly in OMAP3 low power asm code
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
There should be no reason to call h4_init_flash this
early. It causes problems as things are not yet initialized.
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a new clockdomain flag, CLKDM_NO_AUTODEPS, which, when marked on a
clockdomain, will prevent "autodeps" from being associated with the
clockdomain. ("Autodeps" are sleep dependencies and wakeup
dependencies from/to processor modules that are automatically added to
a clockdomain when it is in hardware-supervised idle mode. They are
deprecated -- a relic from the old CDP trees -- but are still in use
for OMAP3.)
Also, prevent the hwmod code from adding or removing initiator
dependencies for clockdomains with this flag set.
This patch should allow others to test which clockdomains actually
still need autodeps.
Thanks to Kevin Hilman <khilman@ti.com> for noting that the original
version should also modify the hwmod code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Create a new API that forms a wrapper to _set_module_autoidle()
to modify the AUTOIDLE bit.
This API is intended to be used by drivers that requires direct
manipulation of the AUTOIDLE bits in SYSCONFIG register.
McBSP driver requires autoidle bit to be enabled/disabled while
using sidetone feature.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: restrict the hwmod states that the autoidle bit can be changed
in; changed function name; dropped "int" from "unsigned int long"]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some boards can't tolerate IP blocks being reset when they are initialized.
Michael Büsch cites a case with the Nokia N810:
http://www.spinics.net/lists/linux-omap/msg47277.html
To allow such boards to continue working normally, allow board file
maintainers to mark IP blocks to prevent them from being reset upon
init. This is done via a hwmod function, omap_hwmod_no_setup_reset().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Michael Buesch <mb@bu3sch.de>
On OMAP2 and OMAP3 the reset ctrl shift doesn't match the
status bit, as it does on OMAP4, when handling the reset lines.
This patch adds a new member in the reset info structure, so now it
can be added as part of hwmod data, and checked accordingly for
OMAP2 or 3; otherwise, there could be cases when the shift masks
doesn't match both of the registers, and a successful reset might
throw an error message or vice versa.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
[paul@pwsan.com: added a warning if st_shift used on OMAP4; renamed 'r'
variable; improved some documentation]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
_init_clock always returns 0 and does
not propogate the error (in case of failure)
back to the caller, causing _init_clocks to
fail silently.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some of the omap2, omap3 peripherals support software reset. This
can be done through the softreset bit in sysconfig register.
The reset status can be checked through resetdone bit of
sysstatus register. syss_has_reset_status is added to the hwmod
database of peripherals which have resetdone bit in sysstatus register.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Reviewed-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Autoidle is a single bit, TIOCP_CFG[0], setting on OMAP1/2/3/4 platforms.
In _set_module_autoidle() I am seeing 0x3 value where the mask is computed.
This should be 0x1.
v2:
(1) Modified the subject.
(2) Modified the description with further specific information.
Baseline:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
Tested Info:
Boot tested on OMAP 1/2/3/4.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Master ports from interconnect are generating some annoying circular
references that become tricky to handle if we have to dynamically
remove some IP on some variant platforms.
Since they are not used for the moment, and since we can still build
that relation using the reverse relation (slave port from the IP
toward master port of the interconnect), let remove them for the
moment like it is done on OMAP4.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Sanjeev Premi <premi@ti.com>
Commit d344272671 ("OMAP3: PM: Adding
smartreflex hwmod data") added data that claims that the L4 CORE has
two slave interfaces that originate from the SmartReflex modules,
omap3_l4_core__sr1 and omap3_l4_core__sr2. But as those two data
structure records show, it's L4 CORE that has a master port towards
SR1 and SR2.
Move the incorrect data from slaves list to master list.
Based on a path by Paul Walmsley <paul@pwsan.com>
https://patchwork.kernel.org/patch/623171/
That is based on a patch by Benoît Cousson <b-cousson@ti.com>:
https://patchwork.kernel.org/patch/590561/
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Cc: Sanjeev Premi <premi@ti.com>
Cc: Thara Gopinath <thara@ti.com>
if building kernels without OMAP2 support, we
will see a warning such as:
arch/arm/mach-omap2/io.c: In function 'omap2_init_common_infrastructure':
arch/arm/mach-omap2/io.c:389:3: warning: statement with no effect
arch/arm/mach-omap2/io.c:391:3: warning: statement with no effect
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
omap_sr_probe() creates the smartreflex debug directory and its
underlying nvalue debug directory. These directories are removed in
omap_sr_remove().
Basic smartreflex functionality tested on OMAP3630 Zoom3 & OMAP4430 SDP
Signed-off-by: Anand S Sawant <sawant@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* Build unconditionally as ARM for correct interoperation with
OMAP firmware.
* Fix an out-of-range ADR when building for ARM.
* Remove deprecated PC-relative stores.
* Add the required ENDPROC() directive for each ENTRY().
* .align before data words.
* Handle non-interworking return from v7_flush_dcache_all.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* Build unconditionally as ARM for correct interoperation with
OMAP firmware.
* Remove deprecated PC-relative stores
* Add the required ENDPROC() directive for each ENTRY().
* .align before data words
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For various reasons, Linux now only officially supports being built
with tools which are new enough to understand the SMC instruction.
Replacing the hand-encoded instructions when the mnemonic also
allows for correct assembly in Thumb-2 (otherwise, the result is
random data in the middle of the code).
The Makefile already ensures that this file is built with a high
enough gcc -march= flag (armv7-a).
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Code marked with ENTRY() also needs a matching ENDPROC() directive,
in order to ensure that the type and instruction set of the
symbol are correctly annotated.
ENDPROC() tags the affected symbol as a function symbol, which will
ensure that link-time fixups don't accidentally switch to the
wrong instruction set.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For CONFIG_THUMB2_KERNEL, the existing definition of do_wfi() will
insert invalid code into the instruction stream.
Any assembler which can assemble Thumb-2 is guaranteed to accept
the "wfi" mnemonic, so for the Thumb-2 case, just use the mnemonic.
The ARM case is left as-is.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
IVA device is not present in many OMAP3 variants.
This patch ensures that initialization is tied to
the presence of IVA on the device.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Voltage control on TWL can be done using VMODE/I2C1/I2C_SR.
Since almost all platforms use I2C_SR on omap3, omap3_twl_init by
default expects that OMAP's I2C_SR is plugged in to TWL's I2C
and calls omap3_twl_set_sr_bit. On platforms where I2C_SR is not connected,
the board files are expected to call omap3_twl_set_sr_bit(false) to
ensure that I2C_SR path is not set for voltage control and prevent
the default behavior of omap3_twl_init.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add a description field to each idle C-state. This helps to give
better data with PowerTop and one don't have to refer to the code
to link what Cx means from system point of view while analysing
PowerTop data.
No functional change.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the custom restore_control_register() and use the exported
set_cr() instead to set the system control register(SCTRL) value.
No functional change.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The OMAP2 and OMAP3 PM code clears clockdomain wakeup and sleep
dependencies. This is unnecessary after commit
6f7f63cc9a ("OMAP clockdomain:
initialize clockdomain registers when the clockdomain layer starts")
which clears these dependencies during clockdomain init.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Now that omap_hwmod + omap_device is used for OMAP UART device and
driver code, we no longer need the UART physical addresses in
omap_globals.
Note that the #defines for the base addresses are still left in
<plat/serial.h> since they are used by DEBUG_LL and uncompress code.
Build tested for OMAP1 (omap1_defconfig) and OMAP2+ (omap2plus_defconfig)
Signed-off-by: Kevin Hilman <khilman@ti.com>
kzalloc() may fail, if so return -ENOMEM. Also Walter Harms suggested
to use kasprintf() instead of kzalloc+strcpy+strcat.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMP3630 silicon can enable higher frequencies only depending on the board
characteristics meeting the recommended standards, and has to be selectively
toggled.
Beagle XM uses 3730 variant and the board design allows enabling 800MHz and
1GHz OPPs. However, We need Smart reflex class 1.5 and ABB to enable 1GHz
safely. For the moment, we tweak the default table to allow for 800Mhz OPP
usage.
Reported-by: Koen Kooi <koen@beagleboard.org>
Tested-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
omap3 and omap4 opp_init should be made non-static to allow
for platform specific opp table tweaking. making these static
conflicts with the definition in pm.h(global) as well.
we include pm.h as well to ensure that there are no such prototype
conflicts with actual implementation in the future.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In case in user has a OMAP3630 < ES1.2 the kernel should warn the user
about the ERRATUM, but using pr_warn instead of WARN_ON is already
enough, as there is nothing else the user can do besides changing the
board.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@canonical.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
According to the hwmod interface data, the DSS submodule "VENC" uses a
clock, "dss_54m_fck"/"dss_tv_fck", which the PRCM cannot autoidle. By
default, the hwmod code assumes that interface clocks can be autoidled
by the PRCM. When the interface clock can't be autoidled by the PRCM,
those interfaces must be marked with the OCPIF_SWSUP_IDLE flag.
Otherwise, the "interface clock" will always have a non-zero use
count, and the device won't enter idle. This problem was observed on
N8x0.
Fix the immediate problem by marking the VENC interface with the
OCPIF_SWSUP_IDLE flag. But it's not clear that
"dss_54m_fck"/"dss_tv_fck" is really the correct interface clock for
VENC. It may be that the VENC interface should use a
hardware-autoidling interface clock. This is the situation on OMAP4,
which uses "l3_div_ck" as the VENC interface clock, which can be
autoidled by the PRCM. Clarification from TI is needed.
Problem found and patch tested on N8x0 by Tony Lindgren
<tony@atomide.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Senthilvadivu Guruswamy <svadivu@ti.com>
Cc: Sumit Semwal <sumit.semwal@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The driver provides the information regarding the ocp errors
that gets logged in the interconnect. The error information
gives the detail regarding the target that was attempted
to be accessed and its corresponding address.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
The l3 interconnect device is build with all the data required
to handle the error logging. The data is extracted from the
hwmod data base.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: sricharan <r.sricharan@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Add the address spaces, irqs of the l3 interconnect to the
hwmod data. The hwmod change is aligned with Benoit Cousson.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: sricharan <r.sricharan@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
The driver provides the information regarding the ocp errors
that gets logged in the interconnect.The error info provides
the details regarding the master or the target that
generated the error, type of error and the corresponding address.
The stack dump is also provided.
Signed-off-by: sricharan <r.sricharan@ti.com>
[r.sricharan@ti.com: Enhacements, major cleanup and made it functional]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[santosh.shilimkar@ti.com: Driver design changes as per OMAP4 version]
Signed-off-by: Felipe Balbi <balbi@ti.com>
[balbi@ti.com: Initial version of the driver]
Acked-by: Benoit Cousson <b-cousson@ti.com>
The l3 interconnect device is build with all the data required
to handle the error logging. The data is extracted from the
hwmod database.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Add the address spaces, irqs of the l3 interconnect to the
hwmod data. The hwmod changes are aligned with Benoit Cousson.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Populate the l2x0 set_debug function pointer with OMAP secure call
and enable the PL310 Errata 727915
This patch has dependency on the earlier patch
ARM: l2x0: Errata fix for flush by Way operation can cause data
corruption
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The i2c_board_info entry supporting AIC23 codec was added into
the i2c2 bus.
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a clockdomain to the GPTIMER7 interface and 2430 HSMMC2 functional
clocks - both were previously missing them.
Also, the 2430 mmchs1_fck is in core_l3_clkdm, but should be in
core_l4_clkdm; fix this.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch fixes these warnings when building kernel for OMAP3EVM
only.
CC arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.o
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:95: warning:
'dsp_24xx_wkdeps' defined but not used
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:119: warning:
'mpu_24xx_wkdeps' defined but not used
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:147: warning:
'core_24xx_wkdeps' defined but not used
The problem should be noticed when building for other OMAP3
platforms (only) as well.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
After commit 81b34fbecb ("OMAP2 clock:
split OMAP2420, OMAP2430 clock data into their own files"), it's
possible to remove dsp_irate_ick from the OMAP2420 and OMAP2430 clock
files. It was originally only needed due to a 2420/2430 clock tree difference,
and now that the data is in separate files, it's superfluous.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the DPLL rate tolerance code that is called during rate
rounding. As far as I know, this code is never used, since it's been
more important for callers of the DPLL round_rate()/set_rate()
functions to obtain an exact rate than it is to save a relatively
small amount of power.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The parent of the interface clocks for GPTIMER1, MPU_WDT,
SYNCTIMER_32K, SCM, WDT1, and the ICR (2430 only) were all listed as
being l4_ck. This isn't accurate; these modules exist inside the WKUP
domain, and the interface clock to these modules runs at the SYS_CLK
rate rather than the CORE L4 rate.
So, create a new clock "wu_l4_ick", similar to the OMAP3
"wkup_l4_ick", that serves as the parent for these clocks.
Also, these clocks were listed as existing inside core_l4_clkdm;
wkup_clkdm is probably more accurate.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP2420/2430 external 32-kHz low-frequency oscillator is a 32768
Hz oscillator, not a 32,000 Hz oscillator[1][2]. Fix this in the clock
tree.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
1. OMAP2420/22 Multimedia Processor Data Manual, Version P [SWPS019P],
section 5.1.4 "External 32-kHz CMOS Clock" (note that it refers to
a "32.768-kHz" clock; this presumably should be "32.768-KHz")
2. OMAP2430 Multimedia Processor ES2.1 Data Manual, Version V [SWPS023V],
section 5.1.4 "External 32-kHz CMOS Clock" (note that it refers to
a "32.768-kHz" clock; this presumably should be "32.768-KHz")
Several clocks are listed as having the core L4 clock as their parent,
when they are actually derived from the L3 clock. Fix these.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
At this point in time, there's no reason for this header file to be in
plat-omap/include/plat/voltage.h. It should not be included by device
drivers, and the code that uses it is currently all under mach-omap2/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There's no reason for this header file to be in
plat-omap/include/plat/smartreflex.h. The hardware devices are in
OMAP2+ SoCs only. Leaving this header file in plat-omap causes
problems due to cross-dependencies with other header files that should
live in mach-omap2/.
Thanks to Benoît Cousson <b-cousson@ti.com> for suggesting the removal
of the smartreflex.h include from the OMAP3xxx hwmod data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
These CM_AUTOIDLE bits are now set by the clock code via the common PM
code in mach-omap2/pm.c.
N.B.: The pm24xx.c code that this patch removes didn't ensure that the
CM_AUTOIDLE bits were set for several 2430-only modules, such as
GPIO5, MDM_INTC, MMCHS1/2, the modem oscillator clock, and USBHS.
Similarly, the pm34xx.c code that this patch removes didn't ensure
that the CM_AUTOIDLE bits were set for USIM and the AM3517 UART4.
Those cases should now be handled.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
OMAP2430 and OMAP3xxx have modem autoidle bits that are actually
attached to clocks with CM_FCLKEN bits; add the code and data to
handle these.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Add sdrc_ick to the OMAP2420 clock data so the clock code can control
the CM_AUTOIDLE bit associated with this clock.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Add interface clock type code with autoidle enable/disable support.
The clkops structures created in this file will be used for all
OMAP2/3 interface clocks with autoidle support. They will enable the
clock framework to control interface clock autoidle directly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Place some comments in the OMAP oscillator clock control code to note that
its autoidle mode should eventually be controlled via the new OMAP clockfw
autoidle control interface.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
OMAP2xxx devices have two on-chip APLLs. These APLLs can
automatically enter idle when not in use. Connect the APLL autoidle
code to the clock code, so that the clock framework can handle this
process. As part of this patch, remove the code in mach-omap2/pm24xx.c
that previously handled APLL autoidle control.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Add the necessary code and data to allow the clock framework to enable
and disable the OMAP2 DPLL autoidle state. This is so the direct
register access can be moved out of the mach-omap2/pm24xx.c code, and other
code that needs to control this (e.g., CPUIdle) can do so via an API.
As part of this patch, remove the pm24xx.c code that formerly wrote
directly to the autoidle bits.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Some drivers wish to know whether the device that they control can
ever lose context, for example, when the device's enclosing
powerdomain loses power. They can use this information to determine
whether it is necessary to save and restore device context, or whether
it can be skipped. Implement the powerdomain portion of this by
adding the function pwrdm_can_ever_lose_context(). This is not for
use directly from driver code, but instead is intended to be called
from driver-subarch integration code (i.e., arch/arm/*omap* code).
Currently, the result from this function should be passed into the
driver code via struct platform_data, but at some point this should
be part of some common or OMAP-specific device code.
While here, update file copyrights.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The bank power state bitfields in the powerdomain data are
encoded incorrectly. These fields are intended to be bitfields,
representing a set of power states that the memory banks support.
However, when only one power state was supported by a given bank,
the field was incorrectly set to the bit shift -- not the mask.
While here, update some file copyrights.
The OMAP4 autogeneration scripts have been updated accordingly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Mark the WKUP powerdomain as being always on -- at least, as long as the
chip has power. This will be used to enable the powerdomain code to
determine whether a given powerdomain is ever able to power off. While
here, update the file copyright.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Most revisions of the OMAP4 Blaze/SDP platform do not have
the EHCI signals routed by default. The pads are routed
for the alternate HSI functionality instead, and explicit
board modifications are needed to route the signals to
the USB PHY on the board.
Also, turning on the PHY connected to the EHCI port causes
a board reboot during bootup due to an unintended short
on the rails - this affects many initial revisions of the
board, and needs a minor board mod to fix (or as a
workaround, one should not attempt to power on the
USB PHY).
Given that these boards need explicit board mods to even
get EHCI working (separate from the accidental short above),
we should not attempt to enable EHCI by default.
So drop the EHCI support from the board files for the
Blaze/SDP platforms.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following commit: 38698be:
OMAP2+: clockevent: set up GPTIMER clockevent hwmod right before timer init
Fixed properly the issue with early init for the timer1
So reverts commit 3b03b58dab that is now
generated a warning at boot time.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap4 interrupt disable bits is different. On rx kfifo full, the mbox rx
interrupts wasn't getting disabled, and this is causing the rcm stress tests
to hang.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Armando Uribe <x0095078@ti.com>
Signed-off-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
twl4030_codec_audio and twl4030_codec_vibra_data has unused field.
In order to remove it, corresponding settings needs to be removed
from board files.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added the KIM (Kernel initialization module for the
Shared Transport driver) device entry in the board file
Only the Blutooth enable GPIO is set for now
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On the OMAP3430LDP board, the ads7846 touchscreen controller
is powered by VAUX1 regulator (supplying 3.0v).
Fix this mapping in the board file, and hence prevent
the ads7846 driver init to fail with the below error..
ads7846 spi1.0: unable to get regulator: -19
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This Patch frees all the dynamically allocated memory
which couldn't have been released in some error hitting cases.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
IVAHD and ABE power domain logic state is populated using directly
value instead of the capability flags.
Fix the same.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: updated to apply at a different point on the tree]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The register naming convention for clock domain control inside
power domain instance is:
OMAPXXXX_<partition>_<power_domain>_<clock_domain>_CDOFFS
Both CPU0 and CPU1 use MPU as clock domain name instead of CPU0
and CPU1.
Change the name to stick to the convention.
The autogen scripts are updated accordingly.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Modifying the device & driver name from "mmci-omap-hs" to
"omap_hsmmc".
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP2420 platform consists of mmc block as in omap1 and not the
hsmmc block as present in omap2430, omap3, omap4 platforms.
Removing all base address macro defines except keeping one for OMAP2420 and
adapting only hsmmc device registration and driver to hwmod framework.
Changes involves:
1) Remove controller reset in devices.c which is taken care of
by hwmod framework.
2) Using omap-device layer to register device and utilizing data from
hwmod data file for base address, dma channel number, Irq_number,
device attribute.
3) Update the driver to use dev_attr to find whether controller
supports dual volt cards
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Reviewed-by: Balaji T K <balajitk@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Moving the definition of mux setting API from devices.c to hsmmc.c
and renaming it from "omap2_mmc_mux" to "omap_hsmmc_mux".
Also calling "omap_hsmmc_mux" from omap2_hsmmc_init.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Chris Ball <cjb@laptop.org
Cc: Tony Lindgren <tony@atomide.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a device attribute to hwmod data of omap2430, omap3, omap4.
Currently the device attribute holds information regarding dual volt MMC card
support by the controller which will be later passed to the host driver via
platform data.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the omap3 hwmod data with the HSMMC info.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the omap2430 hwmod data with the HSMMC info.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MMC controller on the OMAP2420 is different from those
on the OMAP2430, OMAP3 and OMAP4 families - all of the latter
are identical. The one on the OMAP2420 is closer to that
on OMAP1 chips.
Currently, the n8x0 is the only OMAP2420 platform supported
in mainline which registers the MMC controller. Upcoming
changes to register the controllers using hwmod data are
potentially invasive. To reduce the risk, separate out the
2420 controller registration from the common init function
and update its only user. Also seperating out mux settings
for OMAP2420.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The devices of clocks are set to usbhs, so that
only usbhs common driver can invoke these clocks.
The dummy per port clocks are added to omap3
clock data base. This helps to invoke common
clock get APIs for omap3 and omap4.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The prototype and defination of functions usb_ehci_init and
usb_ohci_init are removed. The ehci and ohci devices are
removed since usbhs device contains both ehci and ohci details.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The usbhs intialization is invoked by all omap3 and omap4
variant board files.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A new usbhs platform device is defined;
this device will be the parent device of ehci and
ohci platform devices. the usbhs_init function
is defined which does the usbhs device initialization
and I/O mux of ehci and ohci.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Create the ehci and ohci specific platform data structures.
The port enum values are made common for both ehci and ohci.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We already have both EHCI and OHCI there, so let's
rename to be sure everybody will understand the entire
USB HOST functionality is setup on this file.
Signed-off-by: Felipe Balbi <balbi@ti.com>
add names to EHCI and OHCI resources. That will help us
identify the resource correctly when moving to a setup
where OHCI and EHCI play well together.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Powerdown the internal PHY during board init for OMAP44xx.
So that when musb is disabled core transition to retention/off
is not blocked.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add the context save/restore for the control module register
used for OMAP4430 musb with UTMI embedded PHY interface.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch is again current omap-for-linus branch
Adds platform initialization for working with the WLAN module
attached to the omap3evm.
The patch includes MMC2 initialization, SDIO and control pins
muxing and platform device registration.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Set up the GPTIMER hwmod used for the clockevent source immediately
before it is used. This avoids the need to set up all of the hwmods
until the boot process is further along. (In general, we want to defer
as much as possible until late in the boot process.)
This second version fixes a bug pointed out by Santosh Shilimkar
<santosh.shilimkar@ti.com>, that would cause the kernel to use an
incorrect timer hwmod name if the selected GPTIMER was not 1 or 12 -
thanks Santosh. Also, Tarun Kanti DebBarma <tarun.kanti@ti.com>
pointed out that the original patch did not apply cleanly; this has
now been fixed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Add omap_hwmod_setup_one(), which is intended for use early in boot to
selectively setup the hwmods needed for system clocksources and
clockevents, and any other hwmod that is needed in early boot.
omap_hwmod_setup_all() can then be called later in the boot process.
The point is to minimize the amount of code that needs to be run
early.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Previously, if a hwmod had already been set up, and the code attempted
to set up the hwmod again, an error would be returned. This is not
really useful behavior if we wish to allow the OMAP core code to setup
the hwmods needed for the Linux clocksources and clockevents before
the rest of the hwmods are setup. So, instead of generating errors,
just ignore the attempt to re-setup the hwmod.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Move the code that looks for the MPU initiator hwmod to run during
the individual hwmod _register() function. (Previously, it ran after
all hwmods were registered in the omap_hwmod_late_init() function.)
This is done so code can late-initialize a few individual hwmods --
for example, for the system timer -- before the entire set of hwmods is
initialized later in boot via omap_hwmod_late_init().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Rename omap_hwmod_init() to omap_hwmod_register(). Rename
omap_hwmod_late_init() to omap_hwmod_setup_all(). Also change all of
the callers to reflect the new names. While here, update some
copyrights.
Suggested by Tony Lindgren <tony@atomide.com>.
N.B. The comment in mach-omap2/serial.c may no longer be correct, given
recent changes in init order.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
There's no longer any reason why we should prevent multiple
calls to omap_hwmod_init(). It is now simply used to register an
array of hwmods.
This should allow a subset of hwmods (e.g., hwmods
handling the system clocksource and clockevents) to be registered
earlier than the remaining mass of hwmods.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Disable autoidle on all clocks during clock framework initialization.
(If CONFIG_PM is set, autoidle is re-enabled for all clocks later in
the boot process.)
The principle behind this patch, and some similar patches, is that the
kernel should start with all power management features disabled.
Later in the boot process, the PM code, if compiled in with CONFIG_PM,
enables or re-enables power management features.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Enable hardware gate control for all dpll MX and X2 postdividers.
This requires the allow_idle/deny_idle functions to be
populated for all clock nodes (mx/x2 post dividers) in
clkops.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4, the dpll post divider outputs (MX outputs)
along with clockout_x2 output provide a way to allow/deny
hardware level autogating.
Allowing autoidle would mean that the hw would autogate
this clock when there is no dependency for it.
Denying idle would mean that this clock output will be
forced to stay enabled.
Add dpll api's to read/allow/deny idle control
for these dpll mx postdividers.
NOTE: The gatectrl bit set to 0 allows gatectrl,
and the bit set to 1 denies gatectrl.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: moved OMAP4-specific DPLL control code to
mach-omap2/dpll44xx.c; added some documentation for CLOCK_CLKOUTX2]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Attempt to enable autoidle for as many clocks as possible in the
OMAP2+-common CONFIG_OMAP_RESET_CLOCKS code. Currently, this only
enables DPLL autoidle for OMAP3/4 DPLLs; but future patches will
enable autoidle for other clocks and the OMAP2 DPLL/APLLs.
In the long run, we should probably get rid of
CONFIG_OMAP_RESET_CLOCKS, and unconditionally run the code that it
selects. Otherwise, the state of the clock tree won't match the
hardware state - this could result in clocks being enabled or disabled
unpredictably.
Based on a patch by Rajendra Nayak <rnayak@ti.com> that did this in
the pm34xx.c/pm44xx.c code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
All OMAP3/4 dpll's support hardware level autogating.
Populate allow_idle/deny_idle function pointers for all
DPLL's in clkops.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DPLL1 on omap3 is very similar to the rest of
the non-core dpll's.
Hence populate clkops_omap3_noncore_dpll_ops
as the clkops for it, instead of the
currently populated clkops_null.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Check if enable/disable operations are supported for a given
clock node before attempting to call them.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Now that wkup and sleep dependencies are supported (in the
form of static deps) for OMAP4, remove all instances of
pr_errs' stating dependencies are still unsupported
on OMAP4.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add OMAP4 platform specific implementation to support clkdm
wkup and sleep dependencies a.k.a static dependencies.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: removed comment about PRM; zero-prefixed STATICDEP
register offset; fixed loop termination condition in
omap4_clkdm_clear_all_wkup_sleep_deps(); thanks to Kevin Hilman for finding
and helping fix this bug]
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add new OMAP4 CM accesor apis to set/clear and read
bitfields (based on mask) from CM registers.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP4 supports static dependencies and dynamic dependencies
between clock domains. Static dependencies imply both
wakeup as well as sleep dependencies.
Generate all clockdomain static dependency sources.
(Dynamic dependency sources are hardwired and
cannot to controlled from software).
The autogen scripts are updated to generate the contents
of this patch.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Define the following architecture specific funtions for omap2/3/4
.clkdm_clk_enable
.clkdm_clk_disable
Convert the platform-independent framework to call these functions.
Also rename the api's by removing the omap2_ preamble.
Hence call omap2_clkdm_k_enable as clkdm_clk_enable and
omap2_clkdm_clk_disable as clkdm_clk_disable.a
Remove unused functions (_enable/_disable_hwsup) and unsed
headers from clockdomain.c file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Define the following architecture specific funtions for omap2/3/4
.clkdm_allow_idle
.clkdm_deny_idle
Convert the platform-independent framework to call these functions.
Also rename the api's by removing the omap2_ preamble.
Hence call omap2_clkdm_allow_idle as clkdm_allow_idle and
omap2_clkdm_deny_idle as clkdm_deny_idle.
Make the _clkdm_add_autodeps and _clkdm_del_autodeps as non-static
so they can be accessed from OMAP2/3 platform specific code.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Define the following architecture specific funtions for omap2/3/4
.clkdm_sleep
.clkdm_wakeup
Convert the platform-independent framework to call these functions.
Also rename the api's by removing the omap2_ preamble.
Hence call omap2_clkdm_wakeup as clkdm_wakeup and
omap2_clkdm_sleep as clkdm_sleep.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: fixed omap3_clkdm_clear_all_sleepdeps() and
omap2_clkdm_clear_all_wkdeps() to test against the correct
loop termination condition; thanks to Kevin Hilman for finding and
helping fix]
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Define the following architecture specific funtions for omap2/3
.clkdm_add_wkdep
.clkdm_del_wkdep
.clkdm_read_wkdep
.clkdm_clear_all_wkdeps
.clkdm_add_sleepdep
.clkdm_del_sleepdep
.clkdm_read_sleepdep
.clkdm_clear_all_sleepdeps
Convert the platform-independent framework to call these functions.
With this also move the clkdm lookups for all wkdep_srcs and
sleepdep_srcs at clkdm_init.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: fixed loop termination conditions in omap*_clkdm_clear_all_*();
thanks to Kevin Hilman for finding and helping fix those bugs; also
avoid re-resolving clockdomains during init; abstracted out clkdm_dep walk]
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Put infrastructure in place, so arch specific func pointers
can be hooked up to the platform-independent part of the
framework.
This is in preparation of splitting the clockdomain framework into
platform-independent part (for all omaps) and platform-specific
parts.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Trivial fix to remove the unused function declaration
from the powerdomain header.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
CPU0 and CPU1 clockdomain is at the offset of 0x18 from the LPRM base.
The header file has set it wrongly to 0x0. Offset 0x0 is for CPUx power
domain control register
Fix the same.
The autogen scripts is fixed thanks to Benoit Cousson
With the old value, the clockdomain code would access the
*_PWRSTCTRL.POWERSTATE field when it thought it was accessing the
*_CLKSTCTRL.CLKTRCTRL field. In the worst case, this could cause
system power management to behave incorrectly.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: added second paragraph to commit message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
init_early hook runs too early for omap3_mux_init(), so the board
won't boot. Moved to init_machine, then it works just fine.
Signed-off-by: Radek Pilar <mrkva@mrkva.eu>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add SI4713 FM transmitter supplies, platform data and setup to RX-51/N900.
It is connected to line output signals of TLV320AIC34 codec A part.
Driver can be either built-in or a module. It can be tuned with v4l2-ctl
from ivtv-utils. Following examples illustrate the use of it:
v4l2-ctl -d /dev/radio0 --set-ctrl=mute=0 (power up)
v4l2-ctl -d /dev/radio0 -f 107900 (tune 107.9 MHz)
v4l2-ctl -d /dev/radio0 --set-ctrl=mute=1 (power down)
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
