clk_get() return value should be checked with IS_ERR().
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch complements ed919b0 "mmc: sdio: fix runtime PM anomalies by
introducing MMC_CAP_POWER_OFF_CARD" by declaring MMC_CAP_POWER_OFF_CARD
on the ZOOM's wl1271 mmc slot.
This is required in order not to break runtime PM support for the wl1271
sdio driver.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wakeup-on-timer code does not have/need debugfs dependency. Move
the function out of debugfs ifdef.
Fixes compile error when CONFIG_DEBUG_FS is disabled but PM debug is
enabled.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The console semaphore must be held while the OMAP UART devices are
disabled, lest a console write cause an ARM abort (and a kernel crash)
when the underlying console device is inaccessible. These crashes
only occur when the console is on one of the OMAP internal serial
ports.
While this problem has been latent in the PM idle loop for some time,
the crash was not triggerable with an unmodified kernel until commit
6f251e9db1 ("OMAP: UART: omap_device
conversions, remove implicit 8520 assumptions"). After this patch, a
console write often occurs after the console UART has been disabled in
the idle loop, crashing the system. Several users have encountered
this bug:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg38396.htmlhttp://www.mail-archive.com/linux-omap@vger.kernel.org/msg36602.html
The same commit also introduced new code that disabled the UARTs
during init, in omap_serial_init_port(). The kernel will also crash
in this code when earlyconsole and extra debugging is enabled:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg36411.html
The minimal fix for the -rc series is to hold the console semaphore
while the OMAP UARTs are disabled. This is a somewhat overbroad fix,
since the console may not be located on an OMAP UART, as is the case
with the GPMC UART on Zoom3. While it is technically possible to
determine which devices the console or earlyconsole is actually
running on, it is not a trivial problem to solve, and the code to do
so is not really appropriate for the -rc series.
The right long-term fix is to ensure that no code outside of the OMAP
serial driver can disable an OMAP UART. As I understand it, code to
implement this is under development by TI.
This patch is a collaboration between Paul Walmsley <paul@pwsan.com>
and Tony Lindgren <tony@atomide.com>. Thanks to Ming Lei
<tom.leiming@gmail.com> and Pramod <pramod.gurav@ti.com> for their
feedback on earlier versions of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Pramod <pramod.gurav@ti.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Add additional check to omap_uart_resume_idle() so that only
enabled (specifically, idle-enabled) UARTs are allowed to resume.
This matches the existing check in prepare idle.
Without this patch, the system will hang if a board is
configured to register only some uarts instead of all of
them and PM is enabled.
Cc: Govindraj R. <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7c63984b86 (ARM: do not define VMALLOC_END relative to PAGE_OFFSET)
changed VMALLOC_END to be an explicit value. Before this, it was
relative to PAGE_OFFSET and therefore converted to unsigned long
as PAGE_OFFSET is an unsigned long. This introduced the following
build warning. Fix this by changing the explicit defines of
VMALLOC_END to be unsigned long.
CC arch/arm/mm/init.o
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:606: warning: format '%08lx' expects type 'long unsigned int', but argument 12 has type 'unsigned int'
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Uwe Kleine-K <u.kleine-koenig@pengutronix.dee>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes the following error:
>regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
>twl_reg twl_reg.6: can't register VMMC1, -22
>twl_reg: probe of twl_reg.6 failed with error -22
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (215 commits)
ARM: memblock: setup lowmem mappings using memblock
ARM: memblock: move meminfo into find_limits directly
ARM: memblock: convert free_highpages() to use memblock
ARM: move freeing of highmem pages out of mem_init()
ARM: memblock: convert memory detail printing to use memblock
ARM: memblock: use memblock to free memory into arm_bootmem_init()
ARM: memblock: use memblock when initializing memory allocators
ARM: ensure membank array is always sorted
ARM: 6466/1: implement flush_icache_all for the rest of the CPUs
ARM: 6464/2: fix spinlock recursion in adjust_pte()
ARM: fix memblock breakage
ARM: 6465/1: Fix data abort accessing proc_info from __lookup_processor_type
ARM: 6460/1: ixp2000: fix type of ixp2000_timer_interrupt
ARM: 6449/1: Fix for compiler warning of uninitialized variable.
ARM: 6445/1: fixup TCM memory types
ARM: imx: Add wake functionality to GPIO
ARM: mx5: Add gpio-keys to mx51 babbage board
ARM: imx: Add gpio-keys to plat-mxc
mx31_3ds: Fix spi registration
mx31_3ds: Fix the logic for detecting the debug board
...
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030. This functionality was introduced in mfd tree on
track to kernel.org
Sync pandaboard to the same and make mmc work.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adding card detect callback function and card detect configuration
function for MMC1 Controller on OMAP4.
Card detect configuration function does initial configuration of the
MMC Control & PullUp-PullDown registers of Phoenix.
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030.
Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect,
the suspend/resume initialization which was done in omap_hsmmc_gpio_init
previously is moved to the probe thus making it generic for both OMAP3 &
OMAP4.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This merges the staging-next tree to Linus's tree and resolves
some conflicts that were present due to changes in other trees that were
affected by files here.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.infradead.org/battery-2.6:
power_supply: Makefile cleanup
bq27x00_battery: Add missing kfree(di->bus) in bq27x00_battery_remove()
power_supply: Introduce maximum current property
power_supply: Add types for USB chargers
ds2782_battery: Fix units
power_supply: Add driver for TWL4030/TPS65950 BCI charger
bq20z75: Add support for more power supply properties
wm831x_power: Add missing kfree(wm831x_power) in wm831x_power_remove()
jz4740-battery: Add missing kfree(jz_battery) in jz_battery_remove()
ds2760_battery: Add missing kfree(di) in ds2760_battery_remove()
olpc_battery: Fix endian neutral breakage for s16 values
ds2760_battery: Fix W1 and W1_SLAVE_DS2760 dependency
pcf50633-charger: Add missing sysfs_remove_group()
power_supply: Add driver for TI BQ20Z75 gas gauge IC
wm831x_power: Remove duplicate chg mask
omap: rx51: Add support for USB chargers
power_supply: Add isp1704 charger detection driver
The machine_kexec() calls outer_disable which can crash on OMAP4
becasue of trustzone restrictions.
This patch overrides the default l2x0_disable with a OMAP4
specific implementation taking care of trustzone
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (50 commits)
davinci: fix remaining board support after io_pgoffst removal
davinci: mityomapl138: make file local data static
arm/davinci: remove duplicated include
davinci: Initial support for Omapl138-Hawkboard
davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom
davinci: add tnetv107x touchscreen platform device
input: add driver for tnetv107x touchscreen controller
davinci: add keypad config for tnetv107x evm board
davinci: add tnetv107x keypad platform device
input: add driver for tnetv107x on-chip keypad controller
net: davinci_emac: cleanup unused cpdma code
net: davinci_emac: switch to new cpdma layer
net: davinci_emac: separate out cpdma code
net: davinci_emac: cleanup unused mdio emac code
omap: cleanup unused davinci mdio arch code
davinci: cleanup mdio arch code and switch to phy_id
net: davinci_emac: switch to new mdio
omap: add mdio platform devices
davinci: add mdio platform devices
net: davinci_emac: separate out davinci mdio
...
Fix up trivial conflict in drivers/input/keyboard/Kconfig (two entries
added next to each other - one from the davinci merge, one from the
input merge)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: Makefile - replace the use of <module>-objs with <module>-y
crypto: hifn_795x - use cancel_delayed_work_sync()
crypto: talitos - sparse check endian fixes
crypto: talitos - fix checkpatch warning
crypto: talitos - fix warning: 'alg' may be used uninitialized in this function
crypto: cryptd - Adding the AEAD interface type support to cryptd
crypto: n2_crypto - Niagara2 driver needs to depend upon CRYPTO_DES
crypto: Kconfig - update broken web addresses
crypto: omap-sham - Adjust DMA parameters
crypto: fips - FIPS requires algorithm self-tests
crypto: omap-aes - OMAP2/3 AES hw accelerator driver
crypto: updates to enable omap aes
padata: add missing __percpu markup in include/linux/padata.h
MAINTAINERS: Add maintainer entries for padata/pcrypt
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
Commit ab69bcd66f (arm: remove
machine_desc.io_pg_offst and .phys_io) could not update
the new boards in the omap tree. This causes the build of
omap2plus_defconfig to fail. Fix this.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Eric Miao <eric.miao at canonical.com>
[tony@atomide.com: updated description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP24xx, UART2 WKEN and WKST registers are in PM_WKEN2_CORE and
PM_WKST2_CORE respecitvely. Fix the OMAP2 register init to use the
correct registers on OMAP24xx.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM35x has musb interface (version 1.8) and uses CPPI41 DMA engine.
It has USB phy built inside the IP itself.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
The omap2plus_defconfig doesn't boot up when built with CONFIG_PM
disabled on the latest linux-omap master. Below are the observations
1. OMAP3 reboots in the middle of boot
--------------------------------------------------
[ 0.000000] Calibrating delay loop... 494.72 BogoMIPS (lpj=1933312)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Security Framework initialized
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] Brought up 1 CPUs
[ 0.000000] SMP: Total of 1 processors activated (494.72 BogoMIPS).
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
U-Boot 1.1.4 (Feb 11 2009 - 16:10:23)
OMAP3430-GP rev 2, CPU-OPP2 L3-165MHz
TI 3430SDP 1.0 Version + mDDR (Boot NOR)
DRAM: 128 MB
Flash: 128 MB
NAND:128 MiB
--------------------------------------------------
2. OMAP4 does a kernel PANIC
-------------------------------------
[ 0.000000] Calibrating delay loop... 1195.29 BogoMIPS (lpj=4669440)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Security Framework initialized
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 16 ways, CACHE_ID 0x410000c2, AUX_CTRL 0x0e050000
[ 0.000000] CPU1: Booted secondary processor
[ 0.000000] Brought up 2 CPUs
[ 0.000000] SMP: Total of 2 processors activated (2395.78 BogoMIPS).
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] mux: Could not set signal i2c2_scl.i2c2_scl
[ 0.000000] mux: Could not set signal i2c2_sda.i2c2_sda
[ 0.000000] mux: Could not set signal i2c3_scl.i2c3_scl
[ 0.000000] mux: Could not set signal i2c3_sda.i2c3_sda
[ 0.000000] mux: Could not set signal i2c4_scl.i2c4_scl
[ 0.000000] mux: Could not set signal i2c4_sda.i2c4_sda
-------------------------------------
This is happening because 'omap_serial_init()' is hanging in the boot.
On OMAP3 the watchdog is generating reboot because devices_init doesn't
happens where as on OMAP4 it just hangs without reboot.
The uart clock is not getting enabled after omap_device_idle as part
of omap_serial_init.
The omap_device_idle(will disable the clock) then omap_uart_block_sleep()
should enable clock back disabled during the boot up phase.
But omap_uart_block_sleep() stuffed version is binded only under
CONFIG_PM and other version is just empty. Hence it is not enabling
clock back as expected
This patch adds uart clock enable code to omap_uart_block_sleep() function
built with CONFIG_PM disabled.
Thanks to Charulatha and Govindraj for their help on this debug.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 914bab936fe0388a529079679e2f137aa4ff548d (OMAP: mach-omap2: Fix
incorrect assignment warnings) changed a pointer from 'u32 *' to
'void *' without also fixing up the pointer arithmetic.
Fix the scratchpad offsets so they are byte offsets instead of
word offsets and thus work correctly with a void pointer base.
Special thanks to Jean Pihet for taking the time track down this
problem and propose an initial solution.
Tested with off-idle and off-suspend on 36xx/Zoom3 and 34xx/omap3evm.
Cc: Manjunath Kondaiah G <manjugk@ti.com>
Reported-by: Jean Pihet <jean.pihet@newoldbits.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Jean Pihet <jean.pihet@newoldbits.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP4 PandaBoard has EHCI port1 hooked up to an external
SMSC3320 transciever. GPIO 1 is used to power on the transceiver
and GPIO 62 for reset on the transceiver.
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Avoid possible crash if CONFIG_MMC_OMAP_HS is not set.
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
remove the second hsmmc definition as it is only used on the
expansion header of the PandaBoard and can be mux for other
functions.
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It seems these comments where accidentally added so remove them.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Fix bit clear. Now it clears all other bits than mask bit where it should
clear only it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Reduce the amount of debugging generated by default when unused clocks
are being disabled by the clock code. The previous code would only
generate debug-level messages, but some people who wished to run
production kernels with debug-level messages enabled reported that the
large number of clock disable messages were slowing boot. Now to
enable clock-by-clock disable messages, DEBUG needs to be defined in
mach-omap2/clock.c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tuukka Tikkanen <tuukka.tikkanen@nokia.com>
Cc: Tim Bird <tim.bird@am.sony.com>
Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap. This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.
In response, move the SCM headers into mach-omap2/.
As part of this, remove the direct SCM access from the OMAP UDC
driver. It was clearly broken. The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Split plat-omap/common.c into three pieces:
1. the 32KiHz sync timer and clocksource code, which now lives in
plat-omap/counter_32k.c;
2. the OMAP2+ common code, which has been moved to mach-omap2/common.c;
3. and the remainder of the OMAP-wide common code, which includes the
deprecated ATAGs code and a deprecated video RAM reservation function.
The primary motivation for doing this is to move the OMAP2+-specific parts
into an OMAP2+-specific file, so that build breakage related to the
System Control Module code can be resolved.
Benoît Cousson <b-cousson@ti.com> suggested a new filename and found
some bugs in the counter_32k.c comments - thanks Benoît.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Previously the OMAP McBSP ASoC driver implemented CLKS switching by
using omap_ctrl_{read,write}l() directly. This is against policy; the OMAP
System Control Module functions are not intended to be exported to drivers.
These symbols are no longer exported, so as a result, the OMAP McBSP ASoC
driver does not build as a module.
Resolve the CLKS clock changing portion of this problem by creating a
clock parent changing function that lives in
arch/arm/mach-omap2/mcbsp.c, and modify the ASoC driver to use it.
Due to the unfortunate way that McBSP support is implemented in ASoC
and the OMAP tree, this symbol must be exported for use by
sound/soc/omap/omap-mcbsp.c.
Going forward, the McBSP device driver should be moved from
arch/arm/*omap* into drivers/ or sound/soc/* and the CPU DAI driver
should be implemented as a platform_driver as many other ASoC CPU DAI
drivers are. These two steps should resolve many of the layering
problems, which will rapidly reappear during a McBSP hwmod/PM runtime
conversions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The OMAP ASoC McBSP code implemented CLKR and FSR signal muxing via
direct System Control Module writes on OMAP2+. This required the
omap_ctrl_{read,write}l() functions to be exported, which is against
policy: the only code that should call those functions directly is
OMAP core code, not device drivers. omap_ctrl_{read,write}*() are no
longer exported, so the driver no longer builds as a module.
Fix the pinmuxing part of the problem by removing calls to
omap_ctrl_{read,write}l() from the OMAP ASoC McBSP code and
implementing signal muxing functions in arch/arm/mach-omap2/mcbsp.c.
Due to the unfortunate way that McBSP support is implemented in ASoC
and the OMAP tree, these symbols must be exported for use by
sound/soc/omap/omap-mcbsp.c.
Going forward, the McBSP device driver should be moved from
arch/arm/*omap* into drivers/ or sound/soc/*, and the CPU DAI driver
should be implemented as a platform_driver as many other ASoC CPU DAI
drivers are. These two steps should resolve many of the layering
problems, which will rapidly reappear during a McBSP hwmod/PM runtime
conversion.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The OMAP3 clock tree already contains the infrastructure to support
clock framework-based McBSP functional clock source switching. But it
did not contain the clkdev aliases for the McBSP code to refer to the
parent clocks in an SoC integration-neutral way. So, add the clkdev
aliases for the parent clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the MCBSP_CLKS clock and the clksel structures needed to support clock
framework-based source switching for McBSPs 1-5. Also, add clkdev
aliases on the parent clocks for the McBSP source switching code, added
in a subsequent patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the MCBSP_CLKS clock and the clksel structures needed to support clock
framework-based source switching for McBSP 1 and 2. Also, add clkdev
aliases on the parent clocks for the McBSP source switching code, added
in a subsequent patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently, if, for example, CONFIG_ARCH_OMAP2420 is not selected, OMAP2420
board files can still be included in the build. This results in link errors:
arch/arm/mach-omap2/built-in.o: In function `omap_generic_map_io':
.../arch/arm/mach-omap2/board-generic.c:51: undefined reference to `omap2_set_globals_242x'
arch/arm/mach-omap2/built-in.o: In function `omap_h4_init':
.../arch/arm/mach-omap2/board-h4.c:330: undefined reference to `omap2420_mux_init'
arch/arm/mach-omap2/built-in.o: In function `omap_h4_map_io':
.../arch/arm/mach-omap2/board-h4.c:373: undefined reference to `omap2_set_globals_242x'
arch/arm/mach-omap2/built-in.o: In function `omap_apollon_init':
.../arch/arm/mach-omap2/board-apollon.c:325: undefined reference to `omap2420_mux_init'
arch/arm/mach-omap2/built-in.o: In function `omap_apollon_map_io':
.../arch/arm/mach-omap2/board-apollon.c:353: undefined reference to `omap2_set_globals_242x'
make: *** [.tmp_vmlinux1] Error 1
Fix this by making the boards depend on the Kconfig option for the
specific SoC that they use.
Also, while here, fix the mach-omap2/board-generic.c file to remove the
dependency on OMAP2420.
Charulatha Varadarajan <charu@ti.com> caught a typo - thanks Charu.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Charulatha Varadarajan <charu@ti.com>
As is done on OMAP3, check omap_uart_can_sleep() as one of the
pre-conditions for entering the idle loop. Without this check,
entering idle introduces large latencies on active UARTs, and is
especially noticable on serial console.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some modules which have 16bit registers can cause imprecise
aborts if a __raw_readl/writel is used to read/write 32 bits.
Add an additional flag to identify modules which have such
hard requirement, and handle it in the hwmod framework.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Inorder to avoid any assumptions from bootloader, the watchdog
timer module is reset during init. This enables the watchdog
timer.
Therefore, it is required to disable WDT after it is reset
during init. Otherwise the system would reboot as per the default
watchdog timer registers settings.
Later, when the watchdog driver is loaded, the watchdog timer settings
is adjusted as per the default timer_margin set in the driver and the
driver would supports the normal operations supported by OMAP watchdog
timer.
Signed-off-by: Charulatha V <charu@ti.com>
Reported-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Aaro Koskinen